X-Fi XtremeMusic and Inspire T7

'Ello,?I want some advice, on some prodcuts I am thinking of buying. I was thinking of getting the X-Fi XtremeMusic sound card and the Inspire T7900 speaker system, I was wondering can that sound card support the 7. speakers and will it work with Windows Vista. I ahve tried looking on the website but cannot find anything about if the sound card will work with that speaker system or not. Sorry for what is? probably a stupid question but untill I buy these I have never used any speakers that cost mroe than ?20 so am not sure on this.

All X-Fi series and audigy2 zs support 7. speakers. I don't know about the support for vista though, but I'm pretty sure that they will finally support it a few months later if you are patient enough.

Similar Messages

  • X-Fi XtremeMusic and

    Hey all. I have seen some '4. and X-Fi anger/distress' on this forum, but my question is slightly different to that problem. Currently I have Realtek AC97 onboard sound. I have a 4. setup. To run it though, I have to select 5. in Realtek properties or the sub doesn't work (This will do for me, I dont care that it's 5. and I don't have a centre speaker, as long as 4 speakers and sub work I'm happy). The Realtek also switches 'Mic In Port' to 'Subwoofer / Centre' and switches 'Line In' to 'Rear Speakers Out'. The 'Line Out' is set to 'Front Speakers Out'. The thing is I have 2 multimedia/pc type speakers as front, two big HI-FI speakers as rears and then a multimedia/pc sub. The speakers are not connected to each other at all. Each are separate unlike most setups where 4 sats go into a sub or something. I was wanting to know do you think this could work with an X-Fi XtremeMusic with my front 2 PC speakers going into lineout , 2 rear HI-FI speakers into lineout 2 and the sub into lineout 3 or wouldn't this work at all with the X-Fi like it does with my Realtek onboard.
    Cheers for help and suggestions.

    Re: X-Fi XtremeMusic and SPDIF bypass with Windows 7l Hello hwoarang5,
    why do you think that this is disabled in Windows 7 and Vista?
    It worked fine in Windows Vista, too.
    Anyway, I've searched yesterday evening?a little bit more and solved the problem myself. To enable SPDIF bypass you have to do the following:
    . enable Digital Input in the Windows 7 sound settings (it'sis disabled by default and I forgot about it).
    2. change the FlexiJack mode in the audio settings of Creative to "Digital E/A".
    3. now enable the "Recordation with bit adjustment" (don't know how this is called exactly in the English version).
    When there is a PCM (DTS and Dolby is not supported) signal now at the Digital Input you should here something now.
    Hope this helps somebody.
    Best regards
    Andreas

  • X-Fi Xtrememusic and all X-Fi products

    I have been corresponding with CL techs via email and telephone re: the connection of my xbox360 to my X-Fi XtremeMusic soundcard via optical cable to produce 5. DD from my analogue speakers (Creative T7700). After doing ALOT of research, many ppl (CL lab techs, other sound card companies, forum members) have stated that this is NOT possible as the decoder of DD lies within the software and NOT the hardware of the X-fi soundcard. Thus, the X-Fi XtremeMusic CAN NOT DECODE 5. DD from an xbox360 and you would need an external decoder like DDTS-00. HOWEVER, I came across several CL techs by email and this is what they told me:
    Email :
    I understand from your email that you like to know if there is specific driver for X-Fi Xtreme Music sound card. I am sorry for any inconvenience this is causing you. Please let me assist you. For your information there is a built-in decoder on the X-Fi Xtreme Music sound card. Therefore the signal from a game console such as an Xbox can be decoded & output to analog speakers. There is no need for an I/O Dri've. You may use a digital Toslink cable to 3.5 mm plug.
    Email 2:
    With regard to your email, please be informed that the X-FI Extreme Music sound card is able to decode the 5. DD signal via optical connection to analog speakers. Instead of purchasing the I/O Console, you can get a Tosslink to Minijack adaptor for the connection from the Xbox to Xfi Extreme Music sound card. Please be informed that the decoding will only work on Win XP and not on a Windows Vista PC. In case if you need any clarification, please do not hesitate to contact us.
    Email 3:
    Prior to getting to the email form on our website, you were asked to try some basic troubleshooting for the issue that you identified. The steps that you were walked through resolve some issues with your product. Some of the information that I provide in this message may be repetiti've but it is still valuable information for troubleshooting your device. Yes it can since the X-Fi XtremeMusic has a built-in decoder.
    Email 4:
    With regard to your email, i believe that you are enquiring on a sound card which is suitable for Xbox connection so that it can output 5. sound via the analog speakers connected to the sound card. To do that, you would need to purchase a XFi Extreme Music sound card and an Xfi I/O Console.
    So this concludes my message. I do not know who is right. I deliberately wrote the names of the authors of the emails above so that other Creative techs can clarify with them. The emails have stated that I can connect use the digital connection from my 360 to the flexijack of the x-fi XtremeMusic and get 5. DD sound but others have stated that I cant since the decoder is in the software. Can someone from CL tech explain to me this discrepancy? Thanks, I appreciate it alot.
    Message Edited by turok_t on 0-0-2009 0:58 AMMessage Edited by turok_t on 0-0-2009 02:00 AMMessage Edited by turok_t on 0-0-2009 02:05 AMAdmin Notes: Thanks for letting us know, please understand that I have to remove the name of the Customer Support Advisors for their privacy.
    Message Edited by KokChoy-CL on <span class='local-date'> 0-2-2009<span class='local-time'> 02:02 [email protected]

    turok_t wrote:
    ...the sound card itself can not decode the signal so its useless.
    I wouldn't say that. The card doesn't need to. It's nicer if it appears to do so than if application programs have to be relied on.
    Yes, I have heard that previous?sound cards (not just Creative) had built in decoders to the hardware. This was for 2 reasons. ) Privacy and copyright reasons from Dolby Digital themselves. 2) Codecs change very quickly which means that the hardware will be obsolete once a new codec is released. Thus, it is more efficient to embedd the codecs in software itself. This is based on one of the correspondences with a CL tech staff member.
    There may have been soundcards that included hardware decoding, but I've only heard of one, which was an early USB-interfaced one by CL which was almost stand-alone in character. I have a vague memory of some card with a DSP chip being programmed for it, but I also have this sense this was vaporware or a baseless claim.
    Almost all soundcards punt and say they support decoding but really just include a copy of PowerDVD or similar that actually does it (which CL has started doing recently, unfortunately), but CL has pretty much been unique in including a driver-based decoder which makes the card look like it does do decoding. As far as I can tell, the Xtrememusic is one of those. ? In most cases these support digital-in decoding from an external digital input, but you usually needed the I/O dri've to have the digital input it supported that for. As I said, the formal manual shows explictly how to make an optical connection from a DVD player to the I/O Dri've or I/O console expressly so the card's decoding can be used to hear DD/DTS on the computer's analog speakers.
    As far as your comment about hardware becoming obsolete, why haven't I heard about this being a problem for DD/DTS receivers. That's hardware,
    isn't it's
    Yes, you will need to specify the source if multiple sources are connected to the sound card.
    Only if more than one is supported and it is not the default. It is entirely possible that if there is more than one external digital input, only one of them is actually supported as a decoding input.
    Well, I think its kinda dumb to put a flexijack that is nonfunctional for digital I/O unless you buy the I/O console or dri've separately. Many consumers, including me, thought that external devices can be directly connected to the flexijack since it is Digital I/O. IMO, this is a bit misleading.
    There is only so much real estate on the card's slot cover, and you can't help that some people are apt to jump to unwarranted conclusions. In fact, you can connect external devices to the flexijack directly, in the output direction such as connecting the card to a receiver's coaxial digital input, but you need the Digital I/O Module to do that optically, or to do either form of digital input. You can do so without the I/O console or dri've in addition. The question is not that the flexijack cannot be used for digital input, it's whether the card's decoding feature supports decoding from it, or only from the digital inputs on the dri've/console. It might, but to say it does or doesn't would be an unwarranted conclusion, since I don't have confirmation either way. I also don't know the effect of Vista, if you're using it, but I know that once again drivers had to be rewritten for it, and when that happens, esoteric features may get broken or not work for awhile. (Microsoft seems to be quite incapable of architecting a stable driver environment.)? Plus, drivers rewritten for Vista might force CL to renegotiate the Dolby licensing, which even might be the reason CL has stopped supplying driver-based decoding in some cases.
    To me, it doesnt really matter how many external digital inputs are connected or whether you can switch between digital inputs?from multiple input sources. The fact remains that the Xtrememusic currently can not decode 5. DD li've regardless if you have an adaptor (optical>3/5mm), I/O module, I/O console. In other words,?you can find many ways to connect external devices to the sound card, but the sound card cant INTERPRET and DECODE those digital inputs.
    It can.
    -Dave
    [email protected]

  • Xi Fi fatality and Inspire T5

    I have audigy LS at the moment and Inspire T5400 5. speakers. I am tempted to buy fatality card.
    Would my present speakers work with the card?
    ThanksMessage Edited by hashmat on 09-23-2005 07:59 PM

    Thanks vey much.Message Edited by hashmat on 09-26-2005 02:4 PM

  • X-Fi XtremeMusic and SPDIF bypass with Windows 7

    Hello
    I moved from Windows Vista to Windows 7 (64 Bit) now I wanted to use the SPDIF bypass option with the Digital I/O Module again, but in the "SPDIF E/A" tab the drop down box "Settings for SPDIF input" is disabled.
    What I need to do to get the SPDIF bypass to work again?
    (I don't need any Dobly/DTS decoding - it's just a simple?PCM signal.)
    Best regards and thanks in advance
    Andreas

    Re: X-Fi XtremeMusic and SPDIF bypass with Windows 7l Hello hwoarang5,
    why do you think that this is disabled in Windows 7 and Vista?
    It worked fine in Windows Vista, too.
    Anyway, I've searched yesterday evening?a little bit more and solved the problem myself. To enable SPDIF bypass you have to do the following:
    . enable Digital Input in the Windows 7 sound settings (it'sis disabled by default and I forgot about it).
    2. change the FlexiJack mode in the audio settings of Creative to "Digital E/A".
    3. now enable the "Recordation with bit adjustment" (don't know how this is called exactly in the English version).
    When there is a PCM (DTS and Dolby is not supported) signal now at the Digital Input you should here something now.
    Hope this helps somebody.
    Best regards
    Andreas

  • X-Fi XtremeMusic and 4GB of R

    I have a X-Fi XtremeMusic card and was planning on adding 4GB of ram to my PC. Are there any knon issues when using X-Fi XtremeMusic and 4GB of ram Right now I have 2GB and no problems at all with my X-Fi XtremeMusic. My OS is Windows Vista 32Bit

    stormy3 wrote:
    CLKillerWanted wrote:
    My experiance is this:
    4gb with windows vista 32bit the x-fi works perfectly, but then depending on which motherboard you have, you get only between 2.8-3.5gb ram.
    That is a 32 bit limitation and really has nothing to do with what motherboard you have. See the link I posted above.
    Im not stupid, I know that. But with a eVGA 680i SLI i get 2.75gb in vista32, and with my current p35 ds4 i get 3.5gb. Mr smartypants!

  • X-Fi XtremeMusic and Audigy 2 ZS in the same

    Can I run these 2 sound cards in the same pc X-Fi XtremeMusic and Audigy 2 ZS?
    Thanks all

    Glad to hear it, thanks for updating the thread
    Cat

  • Audigy 2 ZS Platinum Pro and Inspire T7700 does not recognize Mic on Audio Control

    Hi folks,
    I decided to hook up my headphone and mic sets to the Audio Control Pod for the first time recently to chat online. I'm not sure if I ever tried this when I bought the Inspire T7700 speaker system, but I cannot seem to get any voice to come through in Windows' Sound Recorder (the headphones work fine). I'm hoping that someone here can help...otherwise, I suppose I'll have to find an alternate solution than using my soundcard system.
    Here are some specs:
    OS: Windows XP SP2 and all current updates
    Soundcard: Audigy 2 ZS Platinum Pro
    Speakers: Inspire T7700 with Audio Control Pod (contains the headphone and mic jack)
    Here's what I have tried:
    . Updated drivers to: SBAX_WBUP2_LB_2_09_006.exe
    2. Tested headsets and mics out on another one of my computers with a SoundBlaster Li've. They work fine.
    3. Set each audio source with full volume in the Recording Control window as the source while recording in Windows' Sound Recorder (I know some of these aren't right, but I tried them all nonetheless):
    - MIDI Synth
    - Line-In 3
    - Line-In /Mic (this should be the one, I think)
    - S/PDIF-In
    - Auxiliary (this might be the one for the Audio Control Pod)
    - "What U Hear"
    - Line-In 2
    - CD Digital
    - Wave
    4. Installed the Creative software from the official CD to manage the audio and speaker settings. Retested the same as item 3 above within this software. Same results.
    5. Disconnected the external I/O hub (since I am connecting to the Audio Control Pod, which connects to the speaker system and then my sound card). Interestingly, the Line-In /Mic input disappeared. All that I saw for an input (I believe) was Auxiliary. I tried even that as noted in item 3, but nothing.
    Has anyone had any luck in getting a mic from a headphone set to work with the Audio Control Pod for the Inspire T7700 speaker system along with the Audigy 2 ZS Platinum Pro?
    Thanks in advance for the help!

    Read the FAQ on top of the soundcard forum concerning SPDIF and digital out. The reason is very easy to find out if you read that. In short: the digital out can only send out a PCM stereo signal (which is why you only get FL/FR sound) and an encoded AC-3 signal.

  • X-Fi XtremeMusic and Windows 7

    Hi All,
    I recently bought a used Dell XPS400. Part of the coolness of this "older" computer was the 5. surround sound sound system and awesome audio from the X-Fi XtremeMusic sound card. The sound in the Flight Simulator was stunning, as well as in the couple other older games I loaded. I had great hopes to use the computers multimedia capabilities. I gave it a clean Windows XP installation from the Dell hidden partition, but that had a lot of "trash" stuff included, and the Windows Li've and multimedia stuff wasn't supported by Microsoft, so I decided to pull that the hard dri've with XP out, and install a new HD and load Windows 7 (32 bit) on it.
    I'm really liking Windows 7!
    But, (there has to be a "but"), I lost the 5. surround sound from the X-Fi XtremeMusic card. The front stereo speakers are good, but no center channel/subwoofer, and no rear sound. The drop down box for speakers on the Creative control panel only has an entry for 2.0/2.. No other choice is offered.
    So, I started troubleshooting.
    Went to Creative Labs and got the most current drivers (SBXF_PCDRV_LB_2_8_005) and installed them. Nope.
    Uninstalled the card, deleted the drivers and all Creative software, restarted the computer, shut it down (pulled the plug and drained the MB), installed the card, restarted and installed the drivers again. Nope.
    Checked the speakers with an MP3 device. All the speakers worked, so not a new problem with the sound system hardware.
    Pulled the Windows 7 hard dri've out and reinstalled the XP hard dri've. YES! everything works again. But I want to use Windows 7.
    This is a barebones Windows 7 (32 bit) installation, with only Microsoft Flight Simulator and Norton AntiVirus installed at this point.
    The card has a tag on in stating it is a model SB0460, and the serial number is MASB046760900437P.
    Anything else I can try
    Thanks!
    Grampa Steve

    I'm not sure...
    When I go to the Windows 7 control panel and select the sound panels, I end up with the Creative control panel. I can't find a control panel specific to Windows 7 that controls the speakers selection. I will look more this evening.
    What frustrates me is that it works so well under XP, but I "only" get stereo under W7. Very nice stereo,?mind you!
    Grampa Steve?

  • X-Fi XtremeMusic and 4.1 Analog Speaker Syst

    I have seen discussion about this, but thought I would post my specific problem. I am trying to use a four channel analog speaker system with an?X-Fi XtremeMusic. I plug the two?respecti've analog cables from the speaker system into port and 2 on the sound card. I use the console to set speaker selection to 4/4. and then run the channel test. For me the rear left channel is significantly softer and does not work each of the other channels are fine. I have tried headphones in port 2 on the sound card and get the same result the rear left channel does not work correctly.

    I have seen discussion about this, but thought I would post my specific problem. I am trying to use a four channel analog speaker system with an?X-Fi XtremeMusic. I plug the two?respecti've analog cables from the speaker system into port and 2 on the sound card. I use the console to set speaker selection to 4/4. and then run the channel test. For me the rear left channel is significantly softer and does not work each of the other channels are fine. I have tried headphones in port 2 on the sound card and get the same result the rear left channel does not work correctly.

  • X-Fi XtremeMusic and Digital Out

    Please forgive me if this has been asked before, but here goes...
    I have a WinXP machine with an X-Fi XtremeMusic card that I would like to hook up to my Onkyo TX-SR600 receiver. The ideal situation would be to run a single digital line into the coax digitial input of my receiver. I would like all sounds to pass through the receiver and let the receiver do the decoding if possible.
    Do I need to hook up analog cables for the 6 channels in addition to the digital line?
    Thanks for any help,
    - James T

    No, just run the digital coax to the rec. If you don't have one, you will need a digital coax and a /8 mono to RCA adapter. Radio Shack has these items.
    If you play games and want surround sound, you will have to go to analog out. I acutally have both analog out and digital out. They work well.

  • STATIC with Dell Laptop and Inspire T7900

    I've been getting really annoying interference whenever I plug in my speakers. I also have a problem getting a strong connection through the?output socket in the laptop(alot of wiggling the cable to get half decent sound). And lastly the laptop can only support front and back speakers at the moment. I think I need a USB connection instead, but how does this connect to the Inspire T7900? Is a decoder DDTS-100 the answer to my problems?Any help very much appreciated,Cheers,Michael

    Your best bet is a 5.1 external sound card such as the Creative Live! 24-bit External. Although if you can find a usb2 one that would probably be better. The DDTS-100 is an option if your laptop has digital audio out, you shouldnt get any interference then. Or you could get a usb sound card that has digital and then such a decoder, but its probably cheaper to find a usb sound card with 5.1 analogue out. Just more annoying if you plan to keep taking it with your laptop

  • Photoshop Elements 10 and Inspiration Browser installation help needed.

    Photoshop Elements 10 said delete Inspiration Browser, then reinstall.Keep getting "download error". Was able to install Adobe AIR. Now what do I do?

      If you are using the welcome screen try updating directly from the Organizer but first open your web browser and make sure you are logged in to Photoshop.com on-line.
    Then launch Photoshop Elements Organizer
    On the menu bar click Help >> Elements Inspiration Browser
    Enter your ID and password
    In the installation dialog click Install

  • Looking for design advice and inspiration

    Hi, all. I'm designing a Dreamweaver template for our IT
    department's web apps. Do you have some inspirations on
    design/layout? Our apps need to take advantage of the full browser
    screen (lots of data to display in grids) and need to be standards
    compliant (ADA, XHTML, etc.). In other words, lots of screen real
    estate but still look slick :)
    Any recommendations will be much appreciated. Thanks.

    There are great inspirations here:
    http://cssliquid.com/category/gallery/
    Cheers
    Pablo
    An Eye of Menorca
    www.dellimages.com
    "curious_Lee" <[email protected]> wrote in
    message
    news:evlkud$c4p$[email protected]..
    > Hi, all. I'm designing a Dreamweaver template for our IT
    department's web
    > apps.
    > Do you have some inspirations on design/layout? Our apps
    need to take
    > advantage
    > of the full browser screen (lots of data to display in
    grids) and need to
    > be
    > standards compliant (ADA, XHTML, etc.). In other words,
    lots of screen
    > real
    > estate but still look slick :)
    >
    > Any recommendations will be much appreciated. Thanks.
    >

  • X-FI XtremeMusic and Windows 2

    Does XP driver be supported by Windows 2003 for X-FI XtremeMusic card ?
    If not, do they exist special drivers for this OS?
    Thanks for attention.

    Yes i did a voice recording in both teamspeak 3 and the one included in windows. The sound rises to a bearly ok level at the best of times and the soundquality suffers greatly from having the microphone volume at 100 and the +20dB boost on top of it.
    These are regular microphones that work just fines on friends Windows XP laptop while skypeing etc.

Maybe you are looking for