X-lite Sip Phone Registration Rejected

I have an x-lite sip phone that i added as a third party(basic) sip device on cisco call manager, settings are:
UserID: <Extn No on CUCM>
Domain:<ip address of the CUCM>
Password:<CUCM Digest Credentials>
Authorization Name: <UserID on CUCM>
No Domain Proxy
What could be missing?

Take a look at Mr. Bell's writeup on this:
http://www.netcraftsmen.net/component/content/article/70-unified-communications/766-sip-endpoints-in-cisco-cucm-x-lite-as-an-example.html
Please remember to rate helpful responses and identify helpful or correct answers.

Similar Messages

  • 9971 SIP Phones at remote location status REJECTED

    Hi,
    I have 10 locations, Site 1, 2, ....10. All these locations have 10 phones each. These phone are configured with default SIP Profile. Were registered and working fine. While adding a subscriber I downgraded the cluster. After bringing back to regular version. I find all my phones status shows unknown. 
    I tried to change dhcp option 150 on dhcp router to point different server and reconfigured with the correct tftp ip address. Also I tried to shutdown the interface where phones are connected and bring it back up. Restarted tftp server many times. Even after all these I find my phones in REJECTED state. 
    I know personal reset on each phone will fix this issue. But is there any other way to fix this, since these phones are at remote locations.
    Any help is appreciated.
    Thanks,
    MR

    Hello!
    I think, that the most possible issue is problem with CTL/ITL.
    Certificates were regenerated while downgrading/upgrading and were not propagated to the phones.
    So u should try to delete ITL on the phones.
    Regards,
    Kirill

  • Bandwidth required during registration of ip sip phone

    what is the bandwidth requirement of cisco 9971 model phone during registration?

    Thanks a lot Vivek... I went through it...but I think it talks about the bandwidth provisioning for voice traffic..for signalling and once the call is established....I neeed to know the bandwidth required just for registration ...i.e. in the following steps ( only registration without placing any call)   
    1. The phone contacts the TFTP server and requests the Certificate Trust List file .
    2. The phone contacts the TFTP server and requests its SEP<mac-address>.cnf.xml configuration file.
    3. The Phone downloads the default configuration XMLDefault.cnf.xml file from the TFTP server.
    4. The SIP phone requests a firmware upgrade (Load ID file) and upgrades the firmware image automatically when required for a new version of CUCM.
    5. The phone downloads the SIP dial rules configured for that phone.
    6. The phone Establish connection with the primary CUCM and the TFTP server end to end.
    7. The phone Registers with the primary CUCM server listed in its configuration file.
    8. The phone downloads the appropriate localization files from TFTP.
    9. The phone downloads the softkey configurations from TFTP.
    10. The phone downloads custom ringtones (if any) from TFTP.
    Also, I need t o know if the bandwidth required for this process is same for all phone models or different? Specifically, I need  this data for Cisco 9971 model.Please help...Thanks..

  • 3rd Party SIP phone to CUCM via SIP Proxy

    Hi all,
    This is the scenario i'm currently working on :
    3rd party SIP phone <--> Internet <--> SIP Proxy <--> LAN <--> CUCM
    The SIP proxy basically terminates everything (REGISTER, INVITE, etc), including the RTP stream.
    I can register the 3rd party SIP phone to CUCM and in CUCM and  i can see SIP Proxy IP Address as the registered address of the phone.
    Calls from the 3rd party SIP phone to internal Cisco or internal 3rd party SIP phone and vice versa work like charm.
    The only (fatal) problem is i can only register 1 3rd party SIP phone to CUCM via this SIP proxy.
    Since this SIP Proxy always use its internal IP Address and port 5060 (TCP) as its source of registration, CUCM sees multiple registrations for multiple extensions (users) come from a single IP and port, and rejects the second registration request.
    It seems that CUCM binds a digest user to an IP address and port, therefore cannot accept multiple registrations from a single IP and port.
    Can anyone clarify this?  Or is there any way around this?
    I'm using CUCM 8.6.2 and CUCM 9.X (both do not work).
    Regards,
    Christian

    This is most likely because of the following...
    Because third-party SIP phones do not send a MAC address, they must identify themselves by using digest authentication.
    The REGISTER message includes the following header:
    Authorization: Digest username="xxxxxxxxxx",realm="ccmsipline",nonce="GBauADss2qoWr6k9y3hGGVDAqnLfoLk5",uri="sip:172.18.197.224",algorithm=MD5,response="126c0643a4923359ab59d4f53494552e"
    The username, xxxxxxxxxxx, must match an end user that is configured in the End User Configuration window of Cisco Unified CallManager Administration. The administrator configures the SIP third-party phone with the user; for example, swhite, in the Digest User field of Phone Configuration window.
    See the following document.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/5_1_3/ccmcfg/b09sip3p.html
    Also Try this bug CSCef88775

  • Add third party SIP Phone to CCM 5

    'm not able to register this SIP Phone to the CCM5.0. I have device license that cater all IP Phone models.(LIC-CM-DL-100=)
    I got error message " Login Forbidden" "timeout" in the IP Phone.
    In the CCM, I got this message in Phone COnfig Window
    Registration: Rejected.
    Can you explain on how to register this 3rd party IP phone to CCM?
    Is it CCM able to support SIP Phone?

    Hi,
    This is most likely because of the following...
    Because third-party SIP phones do not send a MAC address, they must identify themselves by using digest authentication.
    The REGISTER message includes the following header:
    Authorization: Digest username="swhite",realm="ccmsipline",nonce="GBauADss2qoWr6k9y3hGGVDAqnLfoLk5",uri="sip:172.18.197.224",algorithm=MD5,response="126c0643a4923359ab59d4f53494552e"
    The username, swhite, must match an end user that is configured in the End User Configuration window of Cisco Unified CallManager Administration. The administrator configures the SIP third-party phone with the user; for example, swhite, in the Digest User field of Phone Configuration window.
    See the following document.
    http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/5_1_3/ccmcfg/b09sip3p.html
    Hope this helps, if so please rate.
    Regards,
    Dave

  • Cisco SIP Phone 9971 won't register on CME 8.6 or 8.5 Please HELP

    Please help me , I have problem with registering Cisco SIP phone 9971 with CME 8.6 on ISR 2901.
    I configured CME for SIP clients, then I add configuration for 9971 phone and create profiles.  Phone downloaded SEP...xml file from CME,after that phone look for g4-tones.xml and gd-sip.jar files, I added them to CME after that phone downloaded them and reboot. Now phone is stuck in some kind of loop and does not register on CME.
    On phone log I can see repeting next few messeges.
    12:01:58a No DNS Server IP
    12:01:59a Updating Trust list
    12:01:59a No Trust List instaled
    12:01:59a SEP04C5AB03B0D.cnf.xml (TFTP)  // at this time phone download SEP...xml file from CME
    12:02:00a VPN Error: VPN is not Configured
    on CME if issue DEBUG TFTP EVENTS i receive next few lines
    *Aug 18 18:20:19.891: TFTP: Looking for CTLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:19.987: TFTP: Looking for ITLSEP04C5A4B03B0D.tlv
    *Aug 18 18:20:20.083: TFTP: Looking for ITLFile.tlv
    *Aug 18 18:20:20.347: TFTP: Looking for SEP04C5A4B03B0D.cnf.xml
    *Aug 18 18:20:20.351: TFTP: Opened flash:/SEP04C5A4B03B0D.cnf.xml, fd 14, size 4585 for process 141
    *Aug 18 18:20:20.363: TFTP: Finished flash:/SEP04C5A4B03B0D.cnf.xml, time 00:00:00 for process 141
    here you can see verison info of CME
    Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(4)M, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2011 by Cisco Systems, Inc.
    Compiled Thu 24-Mar-11 15:31 by prod_rel_team
    ROM: System Bootstrap, Version 15.0(1r)M9, RELEASE SOFTWARE (fc1)
    ELTOSAN_ROUTER uptime is 1 hour, 50 minutes
    System returned to ROM by reload at 16:29:20 UTC Thu Aug 18 2011
    System image file is "flash:/c2900-universalk9-mz.SPA.151-4.M.bin"
    Last reload type: Normal Reload
    Last reload reason: Reload Command
    Cisco CISCO2901/K9 (revision 1.0) with 471040K/53248K bytes of memory.
    Processor board ID FGL1508252Y
    3 Gigabit Ethernet interfaces
    2 terminal lines
    1 Virtual Private Network (VPN) Module
    4 Voice FXO interfaces
    4 Voice FXS interfaces
    1 Internal Services Module (ISM) with Services Ready Engine (SRE)
       Survivable Remote Site Voicemail (SRSV) on Cisco Unity Express (CUE) 8.5.1 in slot/sub-slot 0/0
    DRAM configuration is 64 bits wide with parity enabled.
    255K bytes of non-volatile configuration memory.
    254464K bytes of ATA System CompactFlash 0 (Read/Write)
    License Info:
    License UDI:
    Device#   PID                   SN
    *0        CISCO2901/K9          xxxxxxxxxxxxx
    Technology Package License Information for Module:'c2900'
    Technology    Technology-package          Technology-package
                  Current       Type          Next reboot
    ipbase        ipbasek9      Permanent     ipbasek9
    security      securityk9    Permanent     securityk9
    uc            uck9          Permanent     uck9
    data          None          None          None
    Configuration register is 0x2102
    this is RUNNING CONFIGURATION
    ! Last configuration change at 16:10:12 UTC Thu Aug 18 2011
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname ELTOSAN_ROUTER
    boot-start-marker
    boot system flash:/c2900-universalk9-mz.SPA.151-4.M.bin
    boot-end-marker
    no aaa new-model
    no ipv6 cef
    ip source-route
    no ip routing
    no ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.5.1 192.168.5.10
    ip dhcp excluded-address 192.168.5.200 192.168.5.255
    ip dhcp pool phone
       network 192.168.5.0 255.255.255.0
       default-router 192.168.5.251
       option 150 ip 192.168.5.251
    ip dhcp pool data
       relay source 192.168.2.0 255.255.255.0
       relay destination 192.168.2.201
    multilink bundle-name authenticated
    crypto pki token default removal timeout 0
    voice-card 0
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    fax protocol pass-through g711alaw
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 192.168.5.251 port 5060
    max-dn 6
    max-pool 6
    load 9971 sip9971.9-1-1SR1.loads
    authenticate register
    tftp-path flash:
    create profile sync 0005135312289902
    voice register dn  1
    number 207
    allow watch
    name GossaVM
    label 207
    voice register dn  3
    number 101
    name Dejan
    label 101
    mwi
    voice register pool  1
    id mac 000C.29C5.0011
    number 1 dn 1
    dtmf-relay sip-notify
    username testvm password testera
    codec g711alaw
    voice register pool  3
    id mac 04C5.A4B0.3B0D
    type 9971
    number 3 dn 3
    presence call-list
    dtmf-relay rtp-nte
    username dejan password 1234
    codec g711alaw
    no vad
    license udi pid CISCO2901/K9 sn xxxxxxxxxxxx
    hw-module ism 0
    hw-module pvdm 0/0
    redundancy
    interface GigabitEthernet0/0
    description INTERFACE INTERNAL
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    no mop enabled
    interface GigabitEthernet0/0.2
    description LAN DATA
    encapsulation dot1Q 2
    ip address 192.168.2.251 255.255.255.0
    no ip route-cache
    interface GigabitEthernet0/0.5
    description LAN VOICE
    encapsulation dot1Q 5
    ip address 192.168.5.251 255.255.255.0
    no ip route-cache
    interface ISM0/0
    no ip address
    no ip route-cache
    shutdown
    !Application: SRSV-CUE Running on ISM
    interface GigabitEthernet0/1
    no ip address
    no ip route-cache
    shutdown
    duplex auto
    speed auto
    interface ISM0/1
    description Internal switch interface connected to Internal Service Module
    shutdown
    interface Vlan1
    no ip address
    no ip route-cache
    shutdown
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    snmp-server community public RO
    tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
    tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
    tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
    tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
    tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
    tftp-server flash:sip9971.9-1-1SR1.loads alias sip9971.9-1-1SR1.loads
    tftp-server flash:United_States/g4-tones.xml
    tftp-server flash:English_United_States/gd-sip.jar
    control-plane
    voice-port 0/0/0
    voice-port 0/0/1
    voice-port 0/0/2
    voice-port 0/0/3
    voice-port 0/1/0
    voice-port 0/1/1
    voice-port 0/1/2
    voice-port 0/1/3
    mgcp profile default
    gatekeeper
    shutdown
    line con 0
    line aux 0
    line 67
    no activation-character
    no exec
    transport preferred none
    transport input all
    transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
    stopbits 1
    line vty 0 4
    password jebiga
    login
    transport input all
    end
    I did not have any kind of problem with X-LITE to register to CME. also try with few SCCP phones 7940  and I did not any kind of problem .
    this is content of SEP....xml file for 9971
    <device>
    <deviceProtocol>SIP</deviceProtocol>
    <devicePool>
    <dateTimeSetting>
    <dateTemplate>M/D/YA</dateTemplate>
    <timeZone>Pacific Standard/Daylight Time</timeZone>
    <ntps>
    <ntp priority="0">
    <name>0.0.0.0</name>
    <ntpMode>unicast</ntpMode>
    </ntp>
    </ntps>
    </dateTimeSetting>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <sipPort>5060</sipPort>
    </ports>
    <processNodeName>192.168.5.251</processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <sipProfile>
    <sipProxies>
    <registerWithProxy>true</registerWithProxy>
    </sipProxies>
    <sipCallFeatures>
    <cnfJoinEnabled>true</cnfJoinEnabled>
    <localCfwdEnable>true</localCfwdEnable>
    <callForwardURI>service-uri-cfwdall</callForwardURI>
    <callPickupURI>service-uri-pickup</callPickupURI>
    <callPickupGroupURI>service-uri-gpickup</callPickupGroupURI>
    <callHoldRingback>2</callHoldRingback>
    <semiAttendedTransfer>true</semiAttendedTransfer>
    <anonymousCallBlock>2</anonymousCallBlock>
    <callerIdBlocking>2</callerIdBlocking>
    <dndControl>2</dndControl>
    <remoteCcEnable>true</remoteCcEnable>
    </sipCallFeatures>
    <sipStack>
    <remotePartyID>true</remotePartyID>
    </sipStack>
    <sipLines>
    <line button="1" lineIndex="1">
    <featureID>9</featureID>
    <featureLabel></featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name></name>
    <displayName></displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    <line button="2" lineIndex="2">
    <featureID>9</featureID>
    <featureLabel>101</featureLabel>
    <proxy>USECALLMANAGER</proxy>
    <port>5060</port>
    <name>101</name>
    <displayName>Dejan Rakic</displayName>
    <autoAnswer>
    <autoAnswerEnabled>2</autoAnswerEnabled>
    </autoAnswer>
    <callWaiting>1</callWaiting>
    <authName>dejan</authName>
    <authPassword>1234</authPassword>
    <sharedLine>false</sharedLine>
    <messagesNumber></messagesNumber>
    <ringSettingActive>5</ringSettingActive>
    <forwardCallInfoDisplay>
    <callerName>true</callerName>
    <callerNumber>true</callerNumber>
    <redirectedNumber>true</redirectedNumber>
    <dialedNumber>true</dialedNumber>
    </forwardCallInfoDisplay>
    </line>
    </sipLines>
    <enableVad>true</enableVad>
    <preferredCodec>g711alaw</preferredCodec>
    <dialTemplate></dialTemplate>
    <kpml>1</kpml>
    <phoneLabel></phoneLabel>
    <stutterMsgWaiting>2</stutterMsgWaiting>
    <disableLocalSpeedDialConfig>true</disableLocalSpeedDialConfig>
    <dscpForAudio>184</dscpForAudio>
    <dscpVideo>136</dscpVideo>
    </sipProfile>
    <commonProfile>
    <phonePassword>1234</phonePassword>
    <callLogBlfEnabled>2</callLogBlfEnabled>
    </commonProfile>
    <featurePolicyFile>featurePolicyDefault.xml</featurePolicyFile>
    <loadInformation>sip9971.9-1-1SR1.loads</loadInformation>
    <vendorConfig>
    </vendorConfig>
    <commonConfig>
    <videoCapability>0</videoCapability>
    <ciscoCamera>0</ciscoCamera>
    </commonConfig>
    <sshUserId>dejan</sshUserId>
    <sshPassword>1234</sshPassword>
    <userId></userId>
    <phoneServices>
    <provisioning>2</provisioning>
    <phoneService  type="1" category="0">
    <name>Missed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/MissedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Received Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/ReceivedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="1" category="0">
    <name>Placed Calls</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/PlacedCalls</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    <phoneService  type="2" category="0">
    <name>Voicemail</name>
    <phoneLabel></phoneLabel>
    <url>Application:Cisco/Voicemail</url>
    <vendor></vendor>
    <version></version>
    </phoneService>
    </phoneServices>
    <versionStamp>0131511014412102</versionStamp>
    <userLocale>
    <name>English_United_States</name>
    <langCode>en</langCode>
    </userLocale>
    <networkLocale>United_States</networkLocale>
    <networkLocaleInfo>
    <name>United_States</name>
    </networkLocaleInfo>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <servicesURL>http://192.168.5.251:80/CMEserverForPhone/serviceurl</servicesURL>
    <dscpForSCCPPhoneServices>0</dscpForSCCPPhoneServices>
    <dscpForCm2Dvce>96</dscpForCm2Dvce>
    <transportLayerProtocol>2</transportLayerProtocol>
    </device>

    Hello,
    I'm facing exactly the same problem, that is:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the postings to this Forum, but I have not been able to solve it.
    In my case the commands voice register dn  and  voice register pool are OK.
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

  • Cisco CP-78XX SIP Phone Pickup Not Work on CME

    Hi,
    I configured some SIP phones (CP-7821, CP-7841) with pickup function. Is it the Pickup / GPickup soft keys not function as the SIP phone? If yes, then I can use the FAC to access that? And I tried the FAC std. / custom as the pickup / gpickup  .. both not work ... I don't know how to use the FAC on CME? As the FAC std., if I pickup local, that I should press (**3) > call?
    Ref.:
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmecover.html#45535
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeadm/cmefacs.html#30064
    This is the configuration:
    CME-SIP-Phone#sh run
    Building configuration...
    Current configuration : 5413 bytes
    ! Last configuration change at 11:06:12 UTC Fri Nov 28 2014 by mtlops
    version 15.4
    no service pad
    service tcp-keepalives-in
    service tcp-keepalives-out
    service timestamps debug datetime msec localtime show-timezone
    service timestamps log datetime msec localtime show-timezone
    service password-encryption
    service sequence-numbers
    hostname CME-SIP-Phone
    boot-start-marker
    boot system flash:c2900-universalk9-mz.SPA.154-2.T1.bin
    boot-end-marker
    ! card type command needed for slot/vwic-slot 0/0
    enable secret 5 $XXXXXXXXXXXXXXXXXXXXXXXX
    aaa new-model
    aaa authentication login default local
    aaa authorization console
    aaa authorization exec default local
    aaa session-id common
    ip cef
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp feature access-code
    voice-card 0
     dspfarm
     dsp services dspfarm
    voice service pots
    voice service voip
     ip address trusted list
      ipv4 10.118.0.0 255.255.255.0
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     no supplementary-service h225-notify cid-update
     redirect ip2ip
     fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
     h323
      no h225 timeout keepalive
      call preserve
     sip
      bind control source-interface GigabitEthernet0/0
      bind media source-interface GigabitEthernet0/0
      registrar server expires max 600 min 60
    voice class codec 1
     codec preference 1 g711ulaw
     codec preference 2 g711alaw
     codec preference 3 g729r8
    voice class h323 1
      h225 timeout tcp establish 3
      call preserve
    voice class custom-cptone ABC-Company
     dualtone disconnect
      frequency 425
      cadence 500 500
    voice register pool-type  7821
     description Cisco IP Phone 7821
     reference-pooltype 6921
    voice register pool-type  7841
     description Cisco IP Phone 7841
     reference-pooltype 6941
    voice register global
     mode  cme
     source-address 10.118.0.10 port 5060
     timeouts interdigit 2
     max-dn 200
     max-pool 100
     authenticate register
     authenticate realm all
     timezone 42
     time-format 24
     date-format D/M/Y
     mwi stutter
     mwi reg-e164
     voicemail 5000
     call-feature-uri pickup http://10.118.0.10/pickup
     call-feature-uri gpickup http://10.118.0.10/gpickup
     tftp-path flash:
     file text
     create profile sync 0001170446349417
     ntp-server 10.118.0.10 mode unicast
     ip qos dscp af11 media
     ip qos dscp cs2 signal
     ip qos dscp af43 video
     ip qos dscp 25 service
     camera
     video
    voice register dn  2
     number 1000
     pickup-call any-group
     pickup-group 1
     name BB Leung
     label BB Leung
    voice register dn  3
     number 1001
     pickup-call any-group
     pickup-group 1
     name CC Chan
     label CC Chan
    voice register dn  4
     number 1002
     pickup-call any-group
     pickup-group 1
     name DD Leung
     label DD Leung
    voice register dn  50
     mwi
    voice register template  1
     softkeys hold  Newcall Resume
     softkeys idle  Newcall Redial Gpickup Pickup Cfwdall DND
     softkeys seized  Cfwdall Endcall Redial
     softkeys connected  Confrn Endcall Hold Trnsfer
    voice register pool  1
     busy-trigger-per-button 1
     id mac A8XX.XXXX.XXXX
     type 7841
     number 1 dn 2
     template 1
     dtmf-relay sip-notify
     username 1001 password 112233
     codec g711ulaw
     no vad
    voice register pool  2
     busy-trigger-per-button 1
     id mac 50XX.XXXX.XXXX
     type 7841
     number 1 dn 3
     template 1
     dtmf-relay sip-notify
     username 1002 password 112233
     codec g711ulaw
     no vad
    voice register pool  3
     busy-trigger-per-button 1
     id mac 00XX.XXXX.XXXX
     type 7821
     number 1 dn 4
     template 1
     dtmf-relay sip-notify
     username 1003 password 112233
     codec g711ulaw
     no vad
    license udi pid CISCO2921/K9 sn FHK1407F25D
    license accept end user agreement
    license boot c2900 technology-package uck9
    hw-module pvdm 0/0
    hw-module sm 1
    username mtlops privilege 15 secret 5 $1$0qqx$1WGdfRW.flJrwmY7k8eUy0
    redundancy
    interface Embedded-Service-Engine0/0
     no ip address
     shutdown
    interface GigabitEthernet0/0
     ip address 10.118.0.10 255.255.255.0
     duplex auto
     speed auto
    interface GigabitEthernet0/1
     no ip address
     shutdown
     duplex auto
     speed auto
    interface GigabitEthernet0/2
     no ip address
     shutdown
     duplex auto
     speed auto
    interface SM1/0
     no ip address
     shutdown
     service-module fail-open
    interface SM1/1
     no ip address
    interface Vlan1
     no ip address
    ip forward-protocol nd
    no ip http server
    no ip http secure-server
    ip route 0.0.0.0 0.0.0.0 10.118.0.1
    control-plane
    mgcp behavior rsip-range tgcp-only
    mgcp behavior comedia-role none
    mgcp behavior comedia-check-media-src disable
    mgcp behavior comedia-sdp-force disable
    mgcp profile default
    dspfarm profile 1 conference
     codec g711ulaw
     codec g711alaw
     codec g729ar8
     codec g729abr8
     codec g729r8
     codec g729br8
     maximum sessions 7
     associate application SCCP
     shutdown
    gatekeeper
     shutdown
    telephony-service
     max-conferences 8 gain -6
     transfer-system full-consult
     fac standard
    line con 0
    line aux 0
    line 2
     no activation-character
     no exec
     transport preferred none
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line 67
     no activation-character
     no exec
     transport preferred none
     transport input all
     transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
     stopbits 1
    line vty 0 4
     transport input all
    scheduler allocate 20000 1000
    end
    CME-SIP-Phone#sh telephony-service fac
      telephony-service fac standard
        callfwd all **1
        callfwd cancel **2
        pickup local **3
        pickup group **4
        pickup direct **5
        park **6
        dnd **7
        redial **8
        voicemail **9
        ephone-hunt join *3
        ephone-hunt cancel #3
        ephone-hunt hlog *4
        ephone-hunt hlog-phone *5
        trnsfvm *6
        dpark-retrieval *0
        cancel call waiting *1

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • Cisco SIP Phone 9971 won't register on CME 8.6

    Hello,
    I'm facing a very strange problem:
    a Cisco SIP Phone 9971 won't register on CME 8.6 running on a 2811
    I have read all the related-postings to this and other Forum, but I have not been able to solve it.
    One of the "potential solutions" was to make sure that the Phone had a Line configured.
    But I think that the commands voice register dn  and  voice register pool are properly configured (see config below)
    So frankly, I have no idea what I could be missing.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    Thank you for your reply.
    I did some debugs and the results are very strange!
    This is what I got:
    Feb 24 18:01:12.219: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Sent:
    SIP/2.0 400 Bad Request
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK08011844
    From: ;tag=189c5db6bd09000260cf3daf-289a76d1
    To: ;tag=52488-160A
    Date: Mon, 24 Feb 2014 18:01:12 GMT
    Call-ID: [email protected]
    CSeq: 1000 REFER
    Content-Length: 0
    Contact:
    Feb 24 18:01:12.291: //-1/xxxxxxxxxxxx/SIP/Msg/ccsipDisplayMsg:
    Received:
    REGISTER sip:172.25.140.1 SIP/2.0
    Via: SIP/2.0/UDP 172.35.140.12:5060;branch=z9hG4bK1e9ad079
    From: ;tag=189c5db6bd0900032df02e9c-25d79707
    To:
    Call-ID: [email protected]
    Max-Forwards: 70
    Date: Fri, 01 Jan 1982 00:02:41 GMT
    CSeq: 101 REGISTER
    User-Agent: Cisco-CP9971/9.4.1
    Contact: ;+sip.instance="
    000000-0000-0000-0000-189c5db6bd09>";+u.sip!devicename.ccm.cisco.com="SEP189C5DB
    6BD09";+u.sip!model.ccm.cisco.com="493";video
    Supported: replaces,join,sdp-anat,norefersub,resource-priority,extended-refer,X-
    cisco-callinfo,X-cisco-serviceuri,X-cisco-escapecodes,X-cisco-service-control,X-
    cisco-srtp-fallback,X-cisco-monrec,X-cisco-config,X-cisco-sis-6.0.2,X-cisco-xsi-
    8.0.1
    Content-Length: 0
    Reason: SIP;cause=200;text="cisco-alarm:22 Name=SEP189C5DB6BD09 ActiveLoad=sip99
    71.9-4-1-9.loads InactiveLoad=sip9971.9-3-2SR1-1.loads Last=reset-reset"
    Expires: 3600
    Feb 24 18:01:12.395: voice_reg_get_reg_expires_timer: no voice register pool found
    Feb 24 18:01:12.395: VOICE_REG_POOL: Register request for (1010) from (172.35.140.12)
    Feb 24 18:01:12.395: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: key(1010) contact(172.35.140.12:5060) add to contact table
    Feb 24 18:01:12.395: VOICE_REG_POOL: No entry for (1010) found in contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(1010) contact(172.35.140.12) added to contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) add to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: No entry for (172.35.140.12) found in srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL: key(172.35.140.12) contact(1010) added to srst contact table
    Feb 24 18:01:12.399: VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    But right after these errors, I get the following:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    Feb 24 18:01:12.411: VOICE_REG_POOL: Pool[1]: service-control (reset type: 2) message sent to sip:[email protected]
    Feb 24 18:01:12.411: voice_reg_privacy_update_to_phone: delay sending privacy update during bulk registration
    Feb 24 18:01:12.415: //1/7B0070C28003/SIP/Msg/ccsipDisplayMsg:
    ====================
    And when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    So apparently the Phone is actually registered!
    However, the Phone screens still shows this message: Phone Not Registered.
    So frankly I don't understand what's going on!
    I really hope somebody can help.  Thanks!

  • Cisco SIP Phone 9971 will not register on CME 8.6

    Hello,
    I'm trying to configure a  Cisco SIP Phone 9971,
    but it won't register on CME 8.6, which is running on a 2811
    The Phone shows this error message: Phone Not Registered.
    And when I check the the Status Messages in the Phone, I see the following:
    VPN Error: vpn is not configured
    Actually, it shows all these 4 messages in a constant Loop:
    12:01:59a SEP189C5DB6BD09.cnf.xml (TFTP)
    12:01:59a No Trust List instaled
    12:01:59a Updating Trust list
    12:02:00a VPN Error: VPN is not Configured
    It seems that this VPN Error is keeping the Phone from registering.
    This is repeated for ever and the Phone never registers; at least that's what it appears.
    However, when I do a sh voice register pool, I get the following:
    C2811#sh voice register pool  1
    Pool Tag 1
    Config:
      Mac address is 189C.5DB6.BD09
      Type is 9971
      Number list 1 : DN 1
      Proxy Ip address is 0.0.0.0
      Current Phone load version is Cisco-CP9971/9.4.1
      DTMF Relay is enabled, rtp-nte
      Call Waiting is enabled
      DnD is disabled
      Video is enabled
      Camera is enabled
      Busy trigger per button value is 0
      call-forward b2bua busy 68600
      keep-conference is enabled
      registration expires timer max is 3600 and min is 120
      username adm password adm
      kpml signal is enabled
      Lpcor Type is none
      blf call list is enabled
      Transport type is udp
      service-control mechanism is supported
      registration Call ID is [email protected]
      Registration method: per line
      Privacy feature is not configured.
      Privacy button is disabled
      active primary line is: 1010
      contact IP address: 172.35.140.12 port 5060
      Phone SIS Version:  6.0.2
      GW SIS Version:  1.0.0
    Dialpeers created:
    Dial-peers for Pool 1:
    dial-peer voice 40001 voip
    destination-pattern 1010
    session target ipv4:172.35.140.12:5060
    session protocol sipv2
    dtmf-relay rtp-nte
    digit collect kpml
    codec  g711ulaw bytes 160
    no vad
      call-fwd-busy        68600
      after-hours-exempt   FALSE
    Statistics:
      Active registrations  : 4
      Total SIP phones registered: 1
      Total Registration Statistics
        Registration requests  : 4
        Registration success   : 4
        Registration failed    : 0
        unRegister requests    : 0
        unRegister success     : 0
        unRegister failed      : 0
        Attempts to register
               after last unregister : 0
        Last register request time   : 18:11:43.551 UTC Mon Feb 24 2014
        Last unregister request time :
        Register success time        : 18:11:43.551 UTC Mon Feb 24 2014
        Unregister success time      :
    C2811#
    This sh voice register pool  seems to indicate that the Phone has actually registered.
    But I still get the  Phone Not Registered   message on the screen!
    I did some Debugs and they also seem to indicate that the Phone has indeed registered:
    Feb 24 18:01:12.399: VOICE_REG_POOL: Creating param container for dial-peer 4000
    1.VOICE_REG_POOL pool->tag(1), dn->tag(1), submask(1)
    VOICE_REG_POOL pool_tag(1), dn_tag(1)
    Feb 24 18:01:12.399: VOICE_REG_POOL: Created dial-peer entry of type 0
    Feb 24 18:01:12.399: VOICE_REG_POOL: Registration successful for 1010, registration id is 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: Contact matches pool 1 number list 1
    Feb 24 18:01:12.411: VOICE_REG_POOL: GW SIS: X-cisco-cme-sis-1.0.0
    Feb 24 18:01:12.411: VOICE REGISTER POOL-1 has registered.
                                   Name:SEP189C5DB6BD09 IP:172.35.140.12  DeviceType:Phone
    So frankly, I have no idea why the Phone keeps showing the Phone Not Registered message.
    I'm pasting the Router's config.
    I hope somebody is able to point me in the right direction.
    Here is the config.  Thank you!
    C2811#sh run
    Building configuration...
    version 15.1
    service timestamps debug datetime msec
    service timestamps log datetime msec
    no service password-encryption
    hostname C2811
    no aaa new-model
    dot11 syslog
    ip source-route
    ip cef
    ip dhcp excluded-address 172.25.140.1 172.25.140.10
    ip dhcp excluded-address 172.35.140.1 172.35.140.10
    ip dhcp pool Data
    network 172.25.140.0 255.255.255.0
    default-router 172.25.140.1
    option 150 ip 172.25.140.1
    dns-server 172.25.140.1
    ip dhcp pool Voice
    network 172.35.140.0 255.255.255.0
    default-router 172.35.140.1
    option 150 ip 172.35.140.1
    dns-server 172.35.140.1
    no ip domain lookup
    no ipv6 cef
    multilink bundle-name authenticated
    voice service voip
    allow-connections sip to sip
    sip
      registrar server expires max 3600 min 120
    voice register global
    mode cme
    source-address 172.25.140.1 port 5060
    max-dn 40
    max-pool 42
    load 9971 sip9971.9-4-1-9.loads
    authenticate register
    authenticate realm cisco
    tftp-path flash:
    create profile sync 0004820400584603
    voice register dn  1
    number 1010
    allow watch
    name Phone10
    label Phone10
    mwi
    voice register pool  1
    id mac 189C.5DB6.BD09
    type 9971
    number 1 dn 1
    presence call-list
    dtmf-relay rtp-nte
    username adm password adm
    call-forward b2bua busy 68600
    codec g711ulaw
    no vad
    camera
    video
    voice-card 0
    crypto pki token default removal timeout 0
    crypto pki trustpoint TP-self-signed-1879153754
    enrollment selfsigned
    subject-name cn=IOS-Self-Signed-Certificate-1879153754
    revocation-check none
    rsakeypair TP-self-signed-1879153754
    crypto pki certificate chain TP-self-signed-1879153754
    certificate self-signed 01
    (details ommited)
    license udi pid CISCO2811 sn FTX1146A44H
    username admin privilege 15 password 0 admin
    redundancy
    interface FastEthernet0/0
    no ip address
    duplex auto
    speed auto
    interface FastEthernet0/0.25
    description Data VLAN
    encapsulation dot1Q 25
    ip address 172.25.140.1 255.255.255.0
    interface FastEthernet0/0.35
    description Voice VLAN
    encapsulation dot1Q 35
    ip address 172.35.140.1 255.255.255.0
    interface FastEthernet0/1
    no ip address
    shutdown
    duplex auto
    speed auto
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http timeout-policy idle 600 life 86400 requests 10000
    tftp-server flash:P00308010200.bin
    tftp-server flash:P00308010200.sbn
    tftp-server flash:P00308010200.sb2
    tftp-server flash:P00308010200.loads
    tftp-server flash:SCCP42.9-3-1SR3-1S.loads
    tftp-server flash:apps42.9-3-1ES19.sbn
    tftp-server flash:cnu42.9-3-1ES19.sbn
    tftp-server flash:cvm42sccp.9-3-1ES19.sbn
    tftp-server flash:dsp42.9-3-1ES19.sbn
    tftp-server flash:jar42sccp.9-3-1ES19.sbn
    tftp-server flash:term42.default.loads
    tftp-server flash:term62.default.loads
    tftp-server flash:SCCP45.9-3-1SR3-1S.loads
    tftp-server flash:apps45.9-3-1ES19.sbn
    tftp-server flash:cnu45.9-3-1ES19.sbn
    tftp-server flash:cvm45sccp.9-3-1ES19.sbn
    tftp-server flash:dsp45.9-3-1ES19.sbn
    tftp-server flash:jar45sccp.9-3-1ES19.sbn
    tftp-server flash:term45.default.loads
    tftp-server flash:term65.default.loads
    tftp-server flash:/Ringtones/Ringlist.xml alias Ringlist.xml
    tftp-server flash:/Ringtones/DistinctiveRingList.xml alias DistinctiveRingList.x
    ml
    tftp-server flash:sip9971.9-4-1-9.loads
    tftp-server flash:kern9971.9-4-1-9.sebn
    tftp-server flash:rootfs9971.9-4-1-9.sebn
    tftp-server flash:dkern9971.100609R2-9-4-1-9.sebn
    tftp-server flash:sboot9971.031610R1-9-4-1-9.sebn
    tftp-server flash:skern9971.022809R2-9-4-1-9.sebn
    tftp-server flash:/g4-tones.xml alias United_States/g4-tones.xml
    tftp-server flash:/gd-sip.jar alias English_United_States/gd-sip.jar
    control-plane
    mgcp profile default
    telephony-service
    max-ephones 24
    max-dn 48
    ip source-address 172.25.140.1 port 2000
    cnf-file location flash:
    load 7960-7940 P00308010200
    load 7942 SCCP42.9-3-1SR3-1S.loads
    load 7945 SCCP45.9-3-1SR3-1S.loads
    load 7962 SCCP42.9-3-1SR3-1S.loads
    load 7965 SCCP45.9-3-1SR3-1S.loads
    max-conferences 8 gain -6
    dn-webedit
    transfer-system full-consult
    create cnf-files version-stamp 7960 Feb 11 2014 07:18:32
    ephone-dn  1
    number 1001
    description Phone 1
    name Phone 1
    hold-alert 30 originator
    ephone-dn  2
    number 1002
    description Phone 2
    name Phone 2
    hold-alert 30 originator
    ephone-dn  3
    number 1003
    description Phone 3
    name Phone 3
    hold-alert 30 originator
    ephone  1
    device-security-mode none
    mac-address 001C.58FB.6E0F
    button  1:1
    ephone  2
    device-security-mode none
    mac-address 0014.A981.7F8A
    button  1:2
    ephone  3
    device-security-mode none
    mac-address 0006.5356.A4B8
    button  1:3
    alias exec con conf t
    alias exec sib show ip int brief
    alias exec srb show run | b
    alias exec sri show run int
    line con 0
    exec-timeout 0 0
    logging synchronous
    line aux 0
    line vty 0 4
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    line vty 5 15
    privilege level 15
    login local
    transport input telnet ssh
    transport output telnet ssh
    scheduler allocate 20000 1000
    ntp master 1
    end
    C2811#

    VPN is not Configured prints on all phones now with the built-in VPN client if VPN isn't configured.  That's normal and is just cosmetic.  That should not be causing your registration issues.

  • Incoming calls issue in Third Party SIP Phone

    Hi,
    Yesterday I configured my third party sip phone which is yealink in this case on cucm and successfully registered it with cucm, despite of registration i have some calling issue in this phone. I am able to make outbound calls from this phone to any other phone however issue is related to inbound calls.I tried calling its DN from anywhere but call disconnect after sometime. Also didnt get any proper sip session trace in RTMT. Kindly suggest some step to sortout this issue.
    Thanks

    Dear Manish,
    Call normally dicsonnected after 30-40 sec with termination code 102 in session trace. PFB SDI  trace with 5030 is Thirdparty sip phone and 5033 is c7945. Looking forward for your suggestion.
    CallingPartyNumber=5033
    |DialingPartition=
    |DialingPattern=5030
    |FullyQualifiedCalledPartyNumber=5030
    |DialingPatternRegularExpression=(5030)
    |DialingWhere=
    |PatternType=Enterprise
    |PotentialMatches=NoPotentialMatchesExist
    |DialingSdlProcessId=(0,0,0)
    |PretransformDigitString=5030
    |PretransformTagsList=SUBSCRIBER
    |PretransformPositionalMatchList=5030
    |CollectedDigits=5030
    |UnconsumedDigits=
    |TagsList=SUBSCRIBER
    |PositionalMatchList=5030
    |VoiceMailbox=
    |VoiceMailCallingSearchSpace=PT-LHR-LOCAL:PT-Local:Unityvmpt:PT-F6-Local:PT-ISL-LOCAL:PT-KHI-LOCAL:PT_Operator_LHR:PT_Operator_KHI:PT_Operator_ISL
    |VoiceMailPilotNumber=7103
    |RouteBlockFlag=RouteThisPattern
    |RouteBlockCause=0
    |AlertingName=Syed Ahmer
    |UnicodeDisplayName=Syed Ahmer
    |DisplayNameLocale=1
    |OverlapSendingFlagEnabled=0
    12:17:38.028 |//SIP/SIPUdp/wait_SdlSPISignal: Outgoing SIP UDP message to 172.16.200.21:[5062]:
    [23928282,NET]
    INVITE sip:[email protected]:5062 SIP/2.0
    Via: SIP/2.0/UDP 10.100.200.11:5060;branch=z9hG4bK1ca0cc6e317649
    From: "Syed Ahmer" ;tag=8787406~039e2a80-8561-4586-8954-d01ed2aa12c8-246211918
    To:
    Date: Thu, 30 Jan 2014 07:17:38 GMT
    Call-ID: [email protected]
    Supported: timer,resource-priority,replaces
    Min-SE:  1800
    User-Agent: Cisco-CUCM8.5
    Allow: INVITE, OPTIONS, INFO, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY
    CSeq: 101 INVITE
    Expires: 180
    Allow-Events: presence
    Send-Info: conference, x-cisco-conference
    Alert-Info:
    Contact:
    Remote-Party-ID: "Syed Ahmer" ;party=calling;screen=yes;privacy=off
    Max-Forwards: 70
    Content-Length: 0
    |14,100,50,1.14103336^10.163.14.4^SEP00230432C828
    12:17:38.028 |EnvProcessUdpPort - EnvProcessUdpHandler::fireSignal() varId = 0|14,100,50,1.14103336^10.163.14.4^SEP00230432C828
    12:17:38.028 |EnvProcessUdpHandler::fireSignal - SEND: index = 0, handler = 0xaf299320|*^*^*
    12:17:38.028 |EnvProcessUdpPort::fireSignal - SEND, destination = 172.16.200.21:5062|*^*^*
    12:17:38.028 |EnvProcessUdpPort - EnvProcessUdpHandler::send(buff, 850, 172.16.200.21:5062)|*^*^*

  • MOH in third party sip phones

    Hello , 
    I would like to know if the CUCM support MOH in third party sip phones such as x lite or other ? 
    Now I can only hear silent . 
    Thanx 

    Hi ben Zecharia,
     I found your post looking for MoH in 3rd Party SIP Phone and also found another post that said that CUCM 8.x do not support MoH in 3rd Party SIP Phone (check this link).
    Hope this helps (you and others).

  • Can't get video from SIP phones

    Hi,
    I'm currently running CallManager 6.0.1, and I have enabled phones with IP Communicator on SCCP, and phones with X-lite on SIP. Video calls wonderful between IP communicator phones, and even H323 clients, but when I place a video call using X-lite, on the client it says that it doesn't send any video. I currently configured these phones as Basic SIP phones, so I will try changing them to Advanced SIP phones, but I don't see any options to enable voice on these type of devices.
    Is there any trick on these devices? Any input is greatly appreciated.
    Thanks.

    For this one it just turns out that I needed to create it as an Advanced SIP Client instead of Basic

  • German menu language on 7960G SIP Phone

    Hi All
    I have flashed a 7960G SCCP Phone to SIP Firmware.
    Is there any possibility to give this phone another menu language, like german?
    Or is this running only on SCCP Firmware?
    Thank you

    Hi,
    thank you for the help.
    Now I have these files in my TFTP Server.
    These are my files:
    OS79XX.TXT
    P0S3-08-12-00
    SEP0014A8924D6D.CNF.XML
    <device>
    <devicePool>
    <callManagerGroup>
    <members>
    <member priority="0">
    <callManager>
    <ports>
    <ethernetPhonePort>2000</ethernetPhonePort>
    </ports>
    <processNodeName> </processNodeName>
    </callManager>
    </member>
    </members>
    </callManagerGroup>
    </devicePool>
    <versionStamp>{Jan 01 2005 00:00:00}</versionStamp>
    <loadInformation>P0S3-08-12-00</loadInformation>
    <userLocale>
    <name>German_Germany</name>
    <langCode>de</langCode>
    </userLocale>
    <networkLocale>Germany</networkLocale>
    <idleTimeout>0</idleTimeout>
    <authenticationURL></authenticationURL>
    <directoryURL></directoryURL>
    <idleURL></idleURL>
    <informationURL></informationURL>
    <messagesURL></messagesURL>
    <proxyServerURL></proxyServerURL>
    <servicesURL></servicesURL>
    </device>
    SIP0014A8924D6D.cnf
    # SIP Configuration Generic File
    # Line 1 appearance
    line1_name: 01010101001
    # Line 1 Registration Authentication
    line1_authname: "UNPROVISIONED"
    # Line 1 Registration Password
    line1_password: "UNPROVISIONED"
    # Line 2 appearance
    line2_name: football
    # Line 2 Registration Authentication
    line2_authname: "UNPROVISIONED"
    # Line 2 Registration Password
    line2_password: "UNPROVISIONED"
    ####### New Parameters added in Release 2.0 #######
    # All user_parameters have been removed
    # Phone Label (Text desired to be displayed in upper right corner)
    phone_label: "" ; Has no effect on SIP messaging
    # Line 1 Display Name (Display name to use for SIP messaging)
    line1_displayname: "User ID"
    # Line 2 Display Name (Display name to use for SIP messaging)
    line2_displayname: ""
    ####### New Parameters added in Release 3.0 ######
    # Phone Prompt (The prompt that will be displayed on console and telnet)
    phone_prompt: "SIP Phone" ; Limited to 15 characters (Default - SIP Phone)
    # Phone Password (Password to be used for console or telnet login)
    phone_password: "cisco" ; Limited to 31 characters (Default - cisco)
    # User classifcation used when Registering [ none(default), phone, ip ]
    user_info: none
    SIPDefault.cnf
    # SIP Default Generic Configuration File
    # Image Version
    image_version: P0S381200
    language: german
    # Proxy Server
    proxy1_address: "" ; Can be dotted IP or FQDN
    proxy2_address: "" ; Can be dotted IP or FQDN
    proxy3_address: "" ; Can be dotted IP or FQDN
    proxy4_address: "" ; Can be dotted IP or FQDN
    proxy5_address: "" ; Can be dotted IP or FQDN
    proxy6_address: "" ; Can be dotted IP or FQDN
    # Proxy Server Port (default - 5060)
    proxy1_port: 5060
    proxy2_port: 5060
    proxy3_port: 5060
    proxy4_port: 5060
    proxy5_port: 5060
    proxy6_port: 5060
    # Proxy Registration (0-disable (default), 1-enable)
    proxy_register: 0
    # Phone Registration Expiration [1-3932100 sec] (Default - 3600)
    timer_register_expires: 3600
    # Codec for media stream (g711ulaw (default), g711alaw, g729a)
    preferred_codec: g711ulaw
    # TOS bits in media stream [0-5] (Default - 5)
    tos_media: 5
    # Inband DTMF Settings (0-disable, 1-enable (default))
    dtmf_inband: 1
    # Out of band DTMF Settings (none-disable, avt-avt enable (default), avt_always - always avt )
    dtmf_outofband: avt
    # DTMF dB Level Settings (1-6dB down, 2-3db down, 3-nominal (default), 4-3db up, 5-6dB up)
    dtmf_db_level: 3
    # SIP Timers
    timer_t1: 500 ; Default 500 msec
    timer_t2: 4000 ; Default 4 sec
    sip_retx: 10 ; Default 10
    sip_invite_retx: 6 ; Default 6
    timer_invite_expires: 180 ; Default 180 sec
    ####### New Parameters added in Release 2.0 #######
    # Dialplan template (.xml format file relative to the TFTP root directory)
    dial_template: dialplan
    # TFTP Phone Specific Configuration File Directory
    tftp_cfg_dir: "" ; Example: ./sip_phone/
    # Time Server (There are multiple values and configurations refer to Admin Guide for Specifics)
    sntp_server: "" ; SNTP Server IP Address
    sntp_mode: directedbroadcast ; unicast, multicast, anycast, or directedbroadcast (default)
    time_zone: EST ; Time Zone Phone is in
    dst_offset: 1 ; Offset from Phone's time when DST is in effect
    dst_start_month: April ; Month in which DST starts
    dst_start_day: "" ; Day of month in which DST starts
    dst_start_day_of_week: Sun ; Day of week in which DST starts
    dst_start_week_of_month: 1 ; Week of month in which DST starts
    dst_start_time: 02 ; Time of day in which DST starts
    dst_stop_month: Oct ; Month in which DST stops
    dst_stop_day: "" ; Day of month in which DST stops
    dst_stop_day_of_week: Sunday ; Day of week in which DST stops
    dst_stop_week_of_month: 8 ; Week of month in which DST stops 8=last week of month
    dst_stop_time: 2 ; Time of day in which DST stops
    dst_auto_adjust: 1 ; Enable(1-Default)/Disable(0) DST automatic adjustment
    time_format_24hr: 1 ; Enable(1 - 24Hr Default)/Disable(0 - 12Hr)
    # Do Not Disturb Control (0-off, 1-on, 2-off with no user control, 3-on with no user control)
    dnd_control: 0 ; Default 0 (Do Not Disturb feature is off)
    # Caller ID Blocking (0-disbaled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
    callerid_blocking: 0 ; Default 0 (Disable sending all calls as anonymous)
    # Anonymous Call Blocking (0-disabled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
    anonymous_call_block: 0 ; Default 0 (Disable blocking of anonymous calls)
    # DTMF AVT Payload (Dynamic payload range for AVT tones - 96-127)
    dtmf_avt_payload: 101 ; Default 101
    # Sync value of the phone used for remote reset
    sync: 1 ; Default 1
    ####### New Parameters added in Release 2.1 #######
    # Backup Proxy Support
    proxy_backup: "" ; Dotted IP of Backup Proxy
    proxy_backup_port: 5060 ; Backup Proxy port (default is 5060)
    # Emergency Proxy Support
    proxy_emergency: "" ; Dotted IP of Emergency Proxy
    proxy_emergency_port: 5060 ; Emergency Proxy port (default is 5060)
    # Configurable VAD option
    enable_vad: 0 ; VAD setting 0-disable (Default), 1-enable
    ####### New Parameters added in Release 2.2 ######
    # NAT/Firewall Traversal
    nat_enable: 0 ; 0-Disabled (default), 1-Enabled
    nat_address: "" ; WAN IP address of NAT box (dotted IP or DNS A record only)
    voip_control_port: 5060 ; UDP port used for SIP messages (default - 5060)
    start_media_port: 16384 ; Start RTP range for media (default - 16384)
    end_media_port: 32766 ; End RTP range for media (default - 32766)
    nat_received_processing: 0 ; 0-Disabled (default), 1-Enabled
    # Outbound Proxy Support
    outbound_proxy: "" ; restricted to dotted IP or DNS A record only
    outbound_proxy_port: 5060 ; default is 5060
    ####### New Parameter added in Release 3.0 #######
    # Allow for the bridge on a 3way call to join remaining parties upon hangup
    cnf_join_enable : 1 ; 0-Disabled, 1-Enabled (default)
    ####### New Parameters added in Release 3.1 #######
    # Allow Transfer to be completed while target phone is still ringing
    semi_attended_transfer: 1 ; 0-Disabled, 1-Enabled (default)
    # Telnet Level (enable or disable the ability to telnet into the phone)
    telnet_level: 1 ; 0-Disabled (default), 1-Enabled, 2-Privileged
    ####### New Parameters added in Release 4.0 #######
    # XML URLs
    services_url: "" ; URL for external Phone Services
    directory_url: "" ; URL for external Directory location
    logo_url: "" ; URL for branding logo to be used on phone display
    # HTTP Proxy Support
    http_proxy_addr: "" ; Address of HTTP Proxy server
    http_proxy_port: 80 ; Port of HTTP Proxy Server (80-default)
    # Dynamic DNS/TFTP Support
    dyn_dns_addr_1: "" ; restricted to dotted IP
    dyn_dns_addr_2: "" ; restricted to dotted IP
    dyn_tftp_addr: "" ; restricted to dotted IP
    # Remote Party ID
    remote_party_id: 0 ; 0-Disabled (default), 1-Enabled
    ####### New Parameters added in Release 4.4 #######
    # Call Hold Ringback (0-off, 1-on, 2-off with no user control, 3-on with no user control)
    call_hold_ringback: 0 ; Default 0 (Call Hold Ringback feature is off)
    ####### New Parameters added in Release 6.0 #######
    # Dialtone Stutter for MWI
    stutter_msg_waiting: 0 ; 0-Disabled (default), 1-Enabled
    # RTP Call Statistics (SIP BYE/200 OK message exchange)
    call_stats: 0 ; 0-Disabled (default), 1-Enabled
    xmlDefault.CNF.XML
    <?xml version="1.0"?>
    -<Default>
    -<callManagerGroup>
    -<members>
    -<member priority="0">
    -<callManager>
    -<ports>
    <ethernetPhonePort>2000</ethernetPhonePort>
    </ports>
    <processNodeName/>
    </callManager>
    </member>
    </members>
    <loadInformation6 model="IP Phone 7910"/>
    <loadInformation124 model="Addon 7914"/>
    <loadInformation9 model="IP Phone 7935"/>
    <loadInformation8 model="IP Phone 7940"/>
    <loadInformation7 model="IP Phone 7960">P0S3-8-12-00</loadInformation7>
    <loadInformation20000 model="IP Phone 7905"/>
    <loadInformation30008 model="IP Phone 7902"/>
    <loadInformation30002 model="IP Phone 7920"/>
    <loadInformation30019 model="IP Phone 7936"/>
    <loadInformation30006 model="IP Phone 7970"/>
    <loadInformation30018 model="IP Phone 7961"/>
    <loadInformation30007 model="IP Phone 7912"/>
    </callManagerGroup>
    </Default>
    The folders "German_Germany"; "germany" and the file German_Germany.aar are in TFTP folder,too. But my phone is doing nothing with this files.
    This is the log of TFTP Server:
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:21:54.559]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:21:58.562]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:22:45.892]
    Previously allocated address 192.168.0.6 acked [04/03 13:22:45.893]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:46.037]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:46.038]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:46.038]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:47.036]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:47.036]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:47.036]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:22:51.035]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:22:51.036]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.036]
    Connection received from 192.168.0.6 on port 50799 [04/03 13:22:51.056]
    Read request for file <SEP0014A8924D6D.cnf.xml>. Mode octet [04/03 13:22:51.057]
    File <SEP0014A8924D6D.cnf.xml> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.057]
    Connection received from 192.168.0.6 on port 50800 [04/03 13:22:51.085]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:22:51.086]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.086]
    Connection received from 192.168.0.6 on port 50801 [04/03 13:22:51.105]
    Read request for file <MGC0014A8924D6D.cnf>. Mode octet [04/03 13:22:51.105]
    File <MGC0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:22:51.105]
    Connection received from 192.168.0.6 on port 50802 [04/03 13:22:51.124]
    Read request for file <XMLDefault.cnf.xml>. Mode octet [04/03 13:22:51.127]
    Using local port 65426 [04/03 13:22:51.127]
    <XMLDefault.cnf.xml>: sent 3 blks, 1077 bytes in 0 s. 0 blk resent [04/03 13:22:51.135]
    Connection received from 192.168.0.6 on port 50803 [04/03 13:22:51.180]
    Read request for file <P0S3-8-12-00.loads>. Mode octet [04/03 13:22:51.180]
    Using local port 65427 [04/03 13:22:51.180]
    <P0S3-8-12-00.loads>: sent 1 blk, 458 bytes in 0 s. 0 blk resent [04/03 13:22:51.183]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:24:17.151]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:24:20.150]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:24:34.219]
    Previously allocated address 192.168.0.6 acked [04/03 13:24:34.220]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:34.258]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:34.259]
    Using local port 64133 [04/03 13:24:34.259]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:35.250]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:35.250]
    Using local port 64134 [04/03 13:24:35.250]
    Connection received from 192.168.0.6 on port 50823 [04/03 13:24:39.250]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:24:39.250]
    Using local port 64135 [04/03 13:24:39.250]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:24:39.284]
    Connection received from 192.168.0.6 on port 50824 [04/03 13:24:39.485]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:24:39.485]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:24:39.485]
    TIMEOUT waiting for Ack block #1 [04/03 13:24:49.260]
    TIMEOUT waiting for Ack block #1 [04/03 13:24:50.251]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:26:50.610]
    Previously allocated address 192.168.0.6 acked [04/03 13:26:50.611]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:50.649]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:50.649]
    Using local port 64137 [04/03 13:26:50.649]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:51.641]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:51.642]
    Using local port 64138 [04/03 13:26:51.642]
    Connection received from 192.168.0.6 on port 50857 [04/03 13:26:55.641]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:26:55.641]
    Using local port 64139 [04/03 13:26:55.642]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:26:55.676]
    Connection received from 192.168.0.6 on port 50858 [04/03 13:26:55.874]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:26:55.875]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:26:55.875]
    TIMEOUT waiting for Ack block #1 [04/03 13:27:05.651]
    TIMEOUT waiting for Ack block #1 [04/03 13:27:06.645]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:28:40.670]
    Previously allocated address 192.168.0.6 acked [04/03 13:28:40.671]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:40.813]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:40.813]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:40.814]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:41.803]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:41.804]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:41.804]
    Connection received from 192.168.0.6 on port 50797 [04/03 13:28:45.803]
    Read request for file <CTLSEP0014A8924D6D.tlv>. Mode octet [04/03 13:28:45.803]
    File <CTLSEP0014A8924D6D.tlv> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.804]
    Connection received from 192.168.0.6 on port 50798 [04/03 13:28:45.824]
    Read request for file <SEP0014A8924D6D.cnf.xml>. Mode octet [04/03 13:28:45.824]
    File <SEP0014A8924D6D.cnf.xml> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.824]
    Connection received from 192.168.0.6 on port 50799 [04/03 13:28:45.853]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:28:45.853]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.853]
    Connection received from 192.168.0.6 on port 50800 [04/03 13:28:45.874]
    Read request for file <MGC0014A8924D6D.cnf>. Mode octet [04/03 13:28:45.876]
    File <MGC0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:28:45.876]
    Connection received from 192.168.0.6 on port 50801 [04/03 13:28:45.895]
    Read request for file <XMLDefault.cnf.xml>. Mode octet [04/03 13:28:45.895]
    Using local port 64147 [04/03 13:28:45.895]
    <XMLDefault.cnf.xml>: sent 3 blks, 1077 bytes in 0 s. 0 blk resent [04/03 13:28:45.898]
    Connection received from 192.168.0.6 on port 50802 [04/03 13:28:45.935]
    Read request for file <P0S3-8-12-00.loads>. Mode octet [04/03 13:28:45.936]
    Using local port 64148 [04/03 13:28:45.936]
    <P0S3-8-12-00.loads>: sent 1 blk, 458 bytes in 0 s. 0 blk resent [04/03 13:28:45.937]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:30:28.597]
    Previously allocated address 192.168.0.6 acked [04/03 13:30:28.597]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:28.636]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:28.636]
    Using local port 64149 [04/03 13:30:28.636]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:29.627]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:29.628]
    Using local port 64150 [04/03 13:30:29.628]
    Connection received from 192.168.0.6 on port 50787 [04/03 13:30:33.627]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:30:33.628]
    Using local port 64151 [04/03 13:30:33.628]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:30:33.658]
    Connection received from 192.168.0.6 on port 50788 [04/03 13:30:33.856]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:30:33.856]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:30:33.857]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:30:41.756]
    TIMEOUT waiting for Ack block #1 [04/03 13:30:43.637]
    TIMEOUT waiting for Ack block #1 [04/03 13:30:44.629]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:30:44.759]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:32:11.253]
    Rcvd DHCP inform Msg for IP 192.168.0.9, Mac 02:70:7E:7F:09:01 [04/03 13:32:14.253]
    Rcvd DHCP Rqst Msg for IP 0.0.0.0, Mac 00:14:A8:92:4D:6D [04/03 13:33:50.655]
    Previously allocated address 192.168.0.6 acked [04/03 13:33:50.656]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:50.696]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:50.696]
    Using local port 62124 [04/03 13:33:50.696]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:51.685]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:51.686]
    Using local port 62125 [04/03 13:33:51.686]
    Connection received from 192.168.0.6 on port 50795 [04/03 13:33:55.685]
    Read request for file <SIPDefault.cnf>. Mode octet [04/03 13:33:55.685]
    Using local port 62126 [04/03 13:33:55.685]
    <SIPDefault.cnf>: sent 13 blks, 6203 bytes in 0 s. 0 blk resent [04/03 13:33:55.723]
    Connection received from 192.168.0.6 on port 50796 [04/03 13:33:55.915]
    Read request for file <SIP0014A8924D6D.cnf>. Mode octet [04/03 13:33:55.915]
    File <SIP0014A8924D6D.cnf> : error 2 in system call CreateFile Das System kann die angegebene Datei nicht finden. [04/03 13:33:55.915]
    TIMEOUT waiting for Ack block #1 [04/03 13:34:05.698]
    TIMEOUT waiting for Ack block #1 [04/03 13:34:06.691]
    Is there anybody, who can help me with this problem.

  • SIP phone registering on SIP trunk

    Hi,
    i have a UC 500 connected to our phone provider using a SIP trunk.
    All the phones are SPA508 G
    All is working fine !
    Then, some days ago i added a SIP phone (extention 350) on the UC500, that also worked fine, and then after some minutes all our incoming/outgoing calls were blocked.
    I called my provider that told me that our IP was banned because they have seen to much registration attempt from a bad user that was "350"
    I can confirm with a "sh sip-ua register status" command that i had two sip registration : my SIP trunk and the SIP phone
    Then it seems that the UC 500 is trying to register the SIP phone on the SIP trunk ?
    What am i doing wrong ?
    Is there a command to avoid that ?
    Bellow is how the SIP phone and the SIP trunk are configured
    Many thanks for your help, i was unable to find anything about that, but i guess somebody already had this problem !
    The SIP phone -------------------------------------------------------------------------
    voice service voip
     allow-connections h323 to h323
     allow-connections h323 to sip
     allow-connections sip to h323
     allow-connections sip to sip
     supplementary-service h450.12
     fax protocol none
     modem passthrough nse codec g711ulaw
     sip
      registrar server expires max 3600 min 120
      no update-callerid
    voice class codec 1
     codec preference 1 g711ulaw
     codec preference 2 g729r8
    voice register global
     mode cme
     source-address 10.1.1.1 port 5060
     max-dn 20
     max-pool 20
     load 9971 sip9971.9-2-2
     load 9951 sip9951.9-2-2
     load 8961 sip8961.9-2-2
     load 7971 term71.default
     authenticate register
     authenticate realm xxxxxx.com
     timezone 13
     hold-alert
     mwi stutter
     mwi reg-e164
     create profile sync 0636240803635305
    voice register dn  1
     number 350
     name Conference
     label Conference
    voice register pool  1
     id mac 1234.1234.1234
     number 1 dn 1
     username 350 password 1234
     codec g711ulaw
    The SIP trunk ----------------------------------------------------------------------
    sip-ua
     credentials username user1234 password 1234 realm sipgw9.provider.com
     authentication username user1234 password 1234 no remote-party-id
     retry invite 2
     retry register 10
     timers connect 100
     registrar dns:sipgw9.provider.com expires 3600
     sip-server dns:sipgw9.provider.com

    I'm still searching on the forum, and maybe i found somthing related to my problem, not sure... any advice ?
    Disable outbound proxy on voice register global as by default it will use the outbound proxy configured on the system which would not make sense
    voice register global
      no outbound-proxy
    found there : https://supportforums.cisco.com/discussion/10760741/uc500-sip-server-and-sip-trunk

  • Problems with IP Phones registration to CUCME on SG200-50P

    Problems with IP Phones registration to CUCME on SG200-50P
    System setup:
    - Router Cisco 2811 with IOS 12.4(24)T5 Advanced IP Services, CUCME 7.1, DHCP Server
       with HWIC-4ESW
    - Switches:
       - old - SLM224P
       - new - SG200-50P (SLM2048PT), OS v1.3.2.02
    - IP Phones 7911 and 7931, OS v8.4.2
    One VLAN (for desktops and IP Phones) and one IP subnet, no voice VLAN.
    Network diagram:
    C2811---HWIC-4ESW---SWITCH---IPPhones
    Problem description:
    1. In the old setup with SLM224P everything works fine.
       Connected phones almost immediately (1-2 sec. after power up) get ip address, configuration and registers to CUCME.
    2. When switch is changed to new SG200-50G:
       - ip phones get their ip address and tftp configuration very slowly - about 10-20 seconds
       - ip phones cant register to CUCME at all. On the router with SCCP debugging turned on there is no sing of registration attempt
       - after reconnecting the old SLM224P situation backs to normal
    Things that have been checked or tried without success:
    - ports speed and duplex auto, correct detection - although not tested with manual settings
    - CDP/LLDP on/off
    - smartport mode auto and most static settings, also with disabled smartport
    - power cycle / reset
    - spanning tree and port security settings
    - solutions from that post - https://supportforums.cisco.com/thread/2232161
    None of the above methods worked.
    The only action that allowed ip phones to register was changing smartport role to static IPPhone + Desktop.
    After that when phone was disconnected and then reconnected the problem exists again - no registration (IP Phone status DECEASED in CUCME). Same with power cycle/reset.
    Please advice.
    Thanks in advance.

    1 - You have created the voice vlan?
    Nope, flat network, one ip subnet (10 hosts and 10 phones)
    2 - Have you set a phone on an untagged access port for the voice vlan to see if it works?
    Yep, phones are connected to untagged access ports of the one and only vlan
    3 - Have you tried to set the auto voice vlan on the switch so it dynamically assigns the role for ip phone + desktop?
    Not sure about auto voice vlan setting, although there was no triggers to AVV - no static voice vlan, no CDP/VSDP advertisements of voice vlan.
    We've tested static and auto smartport roles (independently of auto voice vlan feature) with successful auto-detection.
    The switch was pretty much in default out-of-the-box config (beside management parameters).
    4 - When rebooting the switch, you did ensure to save the start up to running config?
    Yes, running to startup
    5 - Have you manually set spanning tree PORT FAST for the phone ports?
    No, we haven't tested that. But portfast should be set automatically for the desktop and ip phone smartport roles.

Maybe you are looking for

  • Server does not support PLAIN or LOGIN authentication

    I try to send mail via XI Mail adapter. My settings are below Transport protocol : SMTP Message protocol : XIPAYLOAD url : smtp://10.44... Authentication Method : Plain User : ... Password... From : To : .... But i give this error   "server does not

  • Bought new iMac 20" Faded Screen

    I just picked up the new 20" iMac today, to replace my old Core Duo 20" iMac, and when I got everything booted and got to the Desktop I noticed the icons appeared to be faded. I did a side by side comparison with my old iMac and the icons on my old i

  • How I can find the  Delivery address changes in purchase order

    Hi Friends, How I can find the  Delivery address changes in purchase order item details.And how i can find who did ths changes.

  • Does adding a 2008 DC to a 2003 AD break NT 4.0 trusts ?

    Hello we have a AD envionrment with 3 2003 DCs and it has a trust to a seperate NT 4.0 domain. We are planning to add a 2008 additional DC to the same existing 2003 domain ; it'll require adprep /forest prep switches. My question here ; does this for

  • Configuring 802.11v - BSS Transition Management on Cisco WLC 5508

    Hi, I am new to the configuration of the WLC, and I am trying to enable 802.11v sub feature called BSS Transition Management. I am using WLC software version 8.0.115.0, but I can't find this feature not in the GUI and not in the CLI. I did, however,