X1 Carbon Gen 3 - maximum external display configuration?

Hello,
I am considering the X1 Carbon Gen 3 for purchase. However, I would like to know if it is possible to drive three external displays.
I currently have two running at 1920x1200 and one running at 2560x1440.
Looking at the notes on the OneLink Pro doc seems to indicate this is not possible with the X1 Carbon.
And while we are at it, same question for the T450S with the 90W Ultra Dock. Looks like it is no problem for that configuration but I just want to check and confirm before I buy another machine.
Thanks!

Received my X1 Gen3 and a OneLink Pro dock; here's what I found:
- The mini-DP connector on the X1 Gen3 can support two external monitors at full 2560x1600 resolution (Dell U3014), along with the built-in display, all active. And, my U3014 monitors are in portrait orientation and the trackpad orientation is fully correct. I didn't try using the HDMI at the same time.
- The OneLink Pro dock will connect to a single U3014 monitor, but the system will not support connecting to a second U3014 over the DP output on the OneLink Pro dock (neither via an external DP hub, nor via the DP hub built into the U3014). Seems the OneLink Pro dock has an internal DP hub and is using a DP terminal device to provide the DVI output, and this device seems like it can't be disabled even when not using the DVI output. One significant problem: with a U3014 in portrait orientation connected to the dock, the laptop trackpad orientation was incorrect for the two monitors!
- With the OneLink Pro dock connected (but no monitors connected to the dock), I can connect a separate mini-DP cable to the X1Gen3 and use the system on two U3014 monitors with the laptop closed. This gets me close to what I need, though I wish Lenovo had a dual-DP dock (or a dock with a single DP output, no additional outputs) - the current situation requires two cables to the X1Gen3, but at least the DP connection is much better than a USB3 connection.

Similar Messages

Maximum external display size?

i've got a 12 inch ibook with an ati 9550 w/ 32mb of vram and i want to upgrade my external monitor from 1024x768 to a much larger 19-20" widescreen. does anyone know what that specific video card can handle? thanks a mill.
gabe

If you are using VGA, the iBook only supports these resolutions:
640 by 480 pixels at 60 Hz
800 by 600 pixels at 75 Hz
1024 by 768 pixels at 75 Hz
It really doesn't matter if the display is 2" across or 20 feet across. For a given resolutions, the pixels will be bigger on a bigger display... there won't be more pixels.
Same principal if you are using the S-video or composite video output.

Carbon w Closed Lid & External display?

I have a 32" LCD and i want to keep the Carbon below it inside a stand shelf nicely tucked below connected to the port replicator.
is it possible?
i am aware Windows 8 allows to keep the laptop on while the lid is closed, but would the lcd stay on and get damaged?
is there a custom option for such a scenario as i describe? i dont want to use the Carons display or keyboard, just the cpu/hd/video

Sorry, I don't know the answer. I just wanted to report that my setup with MBA and 23" Cinema Display works the way you would expect. If nobody else has a solution, taking it in to the Apple Store seems like a good idea. It should be easy for them to reproduce the problem.

Maximum External Display Size for GT70 Dominator Pro 889?

Hey all, new to the forums. I tried googling the subject question but cant seem to find anything. Just got my GT70 Dominator Pro 889, it has the 17.3 inch display, GTX 880 8 GB, 16 GB RAM, i7-4810, and a TB HD with a 128 GB SSD. I figured I'd test it out on my Samsung 60 inch LED TV. It has a refresh rate of 120 HZ and is full HD 1920x1080. I assumed the laptop could handle it but this would be the first time I tried something like this, I always used to use desktops that I build for gaming till now. I ran Max Payne 3 all graphics to the max. Now on just the laptop screen I get insanely solid frame rates, no question about that. I tried using my big screen and the game chugs and struggles with FPS under 20. My question is is my TV wayyyy too big to handle gaming from the laptop or is there something I'm missing? I know this is meant to have an additional 3 screens running at once but I figured why not with the TV but I'm aware 60 inches is a lot of ground to cover.

Hi,
What I think is that it's mainly because it's @120Hz, rather than standard 60. 1920x1080 should be easily handled, as even with my low end notebook (nvidia gt315, i3) I was using my TV @1920x1080 with 60Hz and the only fps drop was around 5 in game like Modern Warfare 2.
Also: it is capable of 3 screens, but not really for such heavy gaming. Even highest end GPU won't handle game at highest settings and with 3 screens; lower video settings a bit from highest and see how it goes. Also make sure that NB's screen is not going to be used while you use TV.

Macbook Pro, how to reset invalid external display resolution?

Hi there. I have a question about the external display configuration.
I recently connected my 2011 Macbook Pro 13" (10.8.2 Mountain Lion) to an external HD-TV using Thunderbolt to VGA adapter. After connecting the TV had 1920x1200 resolution which made the text and everything look very tiny. So I thought I'd lower the resolution a bit. But then I messed up and accidentally changed the resolution and refresh rate for the external display to one that wasn't supported. So the TV went black and gave an error about an invalid resolution. At the same time, on my Macbook screen I had only the background image and display settings dialog. No mouse cursor, no menu bar, no dock etc. So I couldn't do anything.
I disconnected the Thunderbolt adapter and got my Macbook screen back to normal, but when I plugged it in again, the same thing happened. Invalid resolution on TV, just background image and display settings on Macbook screen.
Now, this was just before I was going to give a presentation and it resulted in a very awkward situation with me franticly re-plugging the Thunderbolt adapter and looking just completely clueless In the end I had to borrow my colleague's laptop.
So my question is: when this happens, is there a way I can reset / clear the external display settings back to defaults? They are obviously saved somewhere since replugging the Thunderbolt adapter didn't give me back my original resolution.

A PRAM reset should solve that:
From the article linked above:
Your Mac stores certain settings in a special memory area even if it is turned off. On Intel-based Macs, this is stored in memory known as NVRAM; on PowerPC-based Macs, this is stored in memory known as PRAM.
Information stored in NVRAM / PRAM includes:
Speaker volume
Screen resolution
Startup disk selection
Recent kernel panic information, if any
To reset your PRAM:
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.

External display - maximum resolution only works in safe mode on MBP

I'm having an issue with an external display connected to a 2012 non-retina MacbookPro 15" i7 running 10.9. Monitor is Dell U2713HM, which has a maximum resolution of 2560x1440, and is connected via a Mini-Dipslayport to Displayport cord.
My setup has been working great for over a year, where while at my office I use the macbook closed in "clamshell mode" with the Dell monitor being the only display in use, running at 2560x1440. However today when I came into my office and connected to the dispay as usual, the resolution on the Dell was noticably scaled. System preferences is showing it running Scaled at 1080p, and when I select Best for Display it stretches to a very wide and distorted resolution. I can hold alt and click the Scaled button to display additional resolutions, however the maximum resolution listed is 1600x1200. Same problem regardless of clamshell, mirror, or extended desktop modes.
I've been trying to track down the problem, and have run though the usual procedures: restart, shutdown, reset PRAM, reset SMC, check cord connections, verify disk, repair disk permissions - all to no avail. However when I boot in safe mode the display runs as it should at 2560x1440 without issue, which lets me know its not a problem with the cord or connectioin, but rather something on the OS / GPU side.
I can't for the life of me figure out what is causing the issue. Considering its been working fine for quite some time, and I've made no unusual changes to the MBP in the past 48 hours when the display was working properly, I'm not really sure where to go from here. Hoping to not have to migrate to a new user or repartion my HDD.
Any suggestions on possible solutions?
Thanks.

I stumbled upon a fix. Still not sure what caused the issue in the first place, but for anyone having the same issue, the display override script contained on the site below seems to have fixed the issue.
http://embdev.net/topic/284710

Whats the maximum resolution resolution supported @ 60 Hz on an external display for mid 2014 macbook pro retina 13 inch ?

whats the maximum resolution supported @ 60 Hz on an external display for mid 2014 macbook pro retina 13 inch ?

I don't know where you found 1920x1080, but that isn't the max. The INTERNAL display can even support more than that.
The maximum resolution is really hardware based, and since Thunderbolt 2 has a Mini displayport connector (Mini Displayport 1.2), the max resolution for Mini Displayport is 4k (3840x2160).
PLEASE NOTE: Not all adapters can support that resolution, most monitors that can run 4k @60Hz have Displayport 1.2 (The most recent revision), Mini Displayport 1.2, and HDMI 2.0. DVI dual link can run 4k, but only 24-30Hz, depending on the monitor.
Hope this helps!!

Maximum Thunderbolt/VGA resolution for external displays?

Hi there
Until recently, I've been using a Macbook Air Core 2 Duo with a MiniDisplayPort output. This is connected via the Apple MiniDisplayPort > VGA adaptor to an LG Flatron W2246 22" display, and running 1920x1080 quite happily.
I recently bought the Macbook Pro 15" quad core i7 with the Intel HD 3000 and AMD Radeon 6490M - a much more powerful machine with a much more powerful graphics card.
However, it only seems to allow me a maximum resolution of 1600x1200 on the Thunderbolt external display port - it won't give me an option for 1080p.
Any ideas? It seems strange that the Macbook Air will give me higher resultions!
Thanks

I had similar issues to Jason with the technical documentation. It was clear on the maximum resolutions for the laptop's screen and the max resolution on an external monitor, and the max for single and dual link DVI on the adapter pages, but vague on VGA.
I suspected it should work since I have a PC laptop with a graphics card that is a generation behind that can do the full res of my monitor over VGA, but thank you BSteely for confirming this.

I am getting "The contents cannot be displayed in a frame" error when tried to acces an external URL configured through launchpad(ESS). How to rectify it?

Hi Guys,
We have configured ESS role through launchpad. For viewing payslips we are using an external URL configured through launchpad.
But when we try to access the configured link in ESS role, it displays "The contents cannot be displayed in a frame" .
Should I need to change some parameters/settings in Launchpad so that I could overcome this issue.
Guidance required,
Regards,
Ajeeth Kumar S

Hi Shankar Reddy Chamala,
Thanks for the alternate solution.
But the solution you have provided also ended up with the same error
"The content cannot be displayed in a frame" error.
Some additional information so that you could help me out,
The following is the test report .
HTTP/1.1 200 OK
Server: TIN-AppServer
Strict-Transport-Security: max-age=15552000
Cache-Control: no-cache, no-store, must-revalidate
Pragma: no-cache
Expires: Thu, 01 Jan 1970 00:00:00 GMT
x-frame-options: DENY
Content-Type: text/html; charset=UTF-8
Content-Encoding: gzip
Content-Length: 2421
Date: Thu, 15 May 2014 14:23:14 GMT
Connection: keep-alive
Vary: Accept-Encoding
The tester has mentioned the yellow highlighted property may be a cause for this issue.
I googled that the highlighted property is set by the website owners for security reasons.
Shankar I have another doubt..
Is it feasible to create an HTML document to open the external link and link the HTML document to the iview and then configure the custom iview with launchpad.?
-->If yes can you please elaborate the steps for it.
Thanks and Regards,
Ajeeth Kumar S

X1 Carbon doesn't project to external display using DisplayPort++

Hi there,
My new X1 Carbon does not project when using displayport output (displayport to HDMI cable). TV does not pick up signal from PC and PC does no't detect external display. The HDMI output, however, does work. As far as I know all my drivers have been updated using the Lenovo Update tool and Windows Update. Please advise.
Thanks,
- J .

I have the 15 inch Retina MacBook Pro and I got it to work by getting the following mini DisplayPort to DisplayPort cable :
http://www.amazon.com/gp/product/B002YHYTI6/ref=wms_ohs_product

W540 : What is the maximum resolution of an external display?

I have the thinkpad w540
ID:
20BGCTO1WW
videocard:
nvidia quadro k2100m
Where, where! does it tell me the maximum resolution of an external display using the displayport.
Thanks.
Solved!
Go to Solution.

Have a look at the specifications:
http://psref.lenovo.com/PSREFUploadFile%5CSys/PDF/ThinkPad/ThinkPad%20W540/ThinkPad_W540_Platform_Sp...
Via the Thunderbolt port, you'll get a maximum of 3840x2160 (sometimes called "4K") at a refresh rate of 60 Hz.

Configuring Multiple External Displays EliteBook 8470P

I have an EliteBook 8470P with the AMD Radeon 7570M display adapter. I am looking to use to external displays as well as the laptop display. Can I use both the VGA and Display port outputs to accomplish this without purchasing a docking station? And are there any settings that I need to change to do this?

Max,
Simply plug in two monitors out of the dock's DP and DVI port.
The third display connects to the laptop's DP port.
Best of luck, and enjoy!

10.4 and long waits configuring external displays

I have recently upgraded to 10.4.2. When I connect an external projector to my PB it takes at least 4 times longer than 10.3 for the PB to:
1. detect the external display
2. set the external display resolution
I am spending forever with "blue screens of wait" while the PB sorts itself out.
Anyone else had this experience? This delay is so bad I am considering going back to 10.3.

Your out of lick unless you have DVD Drive, (can't be split into CDs or such), or another PPC Mac around & use FW Target Mode...
http://docs.info.apple.com/article.html?artnum=58583
I'm with ya on the corporate profit Merry-Go-Round thing Robert.

X1 Carbon USB 3.0 dock and external display

Following installation of a series of optional updates, including a BIOS update, my external display (connected to the USB 3.0 dock/port replicator, ref 0A33972) is no longer detected. I get an error message "Displaylink USB graphics software is not compatible with this graphics card or operating system. Please visit www.displaylink.com/software and check if a new software version is available". However, a newly downloaded driver won't install, giving an error message saying I need to use the OEM driver update system.
The Update History showing what I installed yesterday does not include any reference to a Displaylink driver.

Install: https://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=21129&lang=eng&wapkw=usb+3.0+driver
Reboot your machine post install, go into the BIOS and set USB 3.0 to enabled and NOT auto.

External Display Flickers (Intel on board)

Hi,
I have recently made a fresh installation of Arch Linux and trying to setup it for my work environment. I made a basic installation of xfce4 with slim login manager. I wanted to hook my laptop with an external display. I used xrandr to extend my laptop display with the external display. Everything worked fine but my external display flickers insanely bad. I cannot stare at it for > 30s. I dual boot on windows, so I tested the same setup with windows and it worked just fine, out of the box. I even used one of my friend's laptop who's running ubuntu and has the same h/w. It worked out of the box. I have spent more than 8 hours trying to find out where the issue would be and miserably failed. Below are certain logs and output that might help traingulate my issue.
Its a Dell Inspiron N4030, with Intel onboard graphics. I have the xf86-video-intel driver installed and the display works perfectly fine with laptops default display.
Output of xrandr -q
[joker@lucifer ~]$ xrandr -q
Screen 0: minimum 320 x 200, current 2732 x 768, maximum 8192 x 8192
LVDS1 connected 1366x768+0+0 (normal left inverted right x axis y axis) 309mm x 173mm
1366x768 60.0*+
1024x768 60.0
800x600 60.3 56.2
640x480 59.9
VGA1 connected 1366x768+1366+0 (normal left inverted right x axis y axis) 344mm x 194mm
1366x768 60.0*+
1024x768 75.1 72.0 70.1 60.0
832x624 74.6
800x600 72.2 75.0 60.3 56.2
640x480 72.8 75.0 66.7 60.0
720x400 70.1
/var/log/Xorg.0.log
[ 42.854]
X.Org X Server 1.11.2
Release Date: 2011-11-04
[ 42.854] X Protocol Version 11, Revision 0
[ 42.854] Build Operating System: Linux 3.1.0-3-ARCH x86_64
[ 42.854] Current Operating System: Linux lucifer 3.1.0-4-ARCH #1 SMP PREEMPT Mon Nov 7 22:47:18 CET 2011 x86_64
[ 42.854] Kernel command line: root=/dev/sda5 ro
[ 42.854] Build Date: 07 November 2011 07:53:00AM
[ 42.854]
[ 42.854] Current version of pixman: 0.24.0
[ 42.854] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 42.854] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 42.855] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Nov 10 17:07:34 2011
[ 42.901] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 42.927] (==) ServerLayout "DualSreen"
[ 42.927] (**) |-->Screen "Screen0" (0)
[ 42.927] (**) | |-->Monitor "Monitor0"
[ 42.945] (**) | |-->Device "Device0"
[ 42.945] (**) |-->Screen "Screen1" (1)
[ 42.945] (**) | |-->Monitor "Monitor1"
[ 42.945] (**) | |-->Device "Device1"
[ 42.945] (**) Option "Xinerama" "1"
[ 42.945] (==) Automatically adding devices
[ 42.945] (==) Automatically enabling devices
[ 42.945] (**) Xinerama: enabled
[ 43.004] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 43.004] Entry deleted from font path.
[ 43.004] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 43.004] Entry deleted from font path.
[ 43.005] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 43.005] Entry deleted from font path.
[ 43.005] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 43.005] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 43.005] Entry deleted from font path.
[ 43.005] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 43.005] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 43.005] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 43.005] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 43.005] (II) Loader magic: 0x7ccae0
[ 43.005] (II) Module ABI versions:
[ 43.005] X.Org ANSI C Emulation: 0.4
[ 43.005] X.Org Video Driver: 11.0
[ 43.005] X.Org XInput driver : 13.0
[ 43.005] X.Org Server Extension : 6.0
[ 43.006] (--) PCI:*(0:0:2:0) 8086:0046:1028:0466 rev 2, Mem @ 0xfac00000/4194304, 0xc0000000/268435456, I/O @ 0x0000f080/8
[ 43.006] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 43.006] (II) LoadModule: "extmod"
[ 43.027] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 43.043] (II) Module extmod: vendor="X.Org Foundation"
[ 43.043] compiled for 1.11.2, module version = 1.0.0
[ 43.043] Module class: X.Org Server Extension
[ 43.043] ABI class: X.Org Server Extension, version 6.0
[ 43.043] (II) Loading extension MIT-SCREEN-SAVER
[ 43.043] (II) Loading extension XFree86-VidModeExtension
[ 43.043] (II) Loading extension XFree86-DGA
[ 43.043] (II) Loading extension DPMS
[ 43.043] (II) Loading extension XVideo
[ 43.043] (II) Loading extension XVideo-MotionCompensation
[ 43.043] (II) Loading extension X-Resource
[ 43.044] (II) LoadModule: "dbe"
[ 43.044] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 43.045] (II) Module dbe: vendor="X.Org Foundation"
[ 43.045] compiled for 1.11.2, module version = 1.0.0
[ 43.045] Module class: X.Org Server Extension
[ 43.045] ABI class: X.Org Server Extension, version 6.0
[ 43.045] (II) Loading extension DOUBLE-BUFFER
[ 43.045] (II) LoadModule: "glx"
[ 43.045] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 43.060] (II) Module glx: vendor="X.Org Foundation"
[ 43.060] compiled for 1.11.2, module version = 1.0.0
[ 43.060] ABI class: X.Org Server Extension, version 6.0
[ 43.060] (==) AIGLX enabled
[ 43.060] (II) Loading extension GLX
[ 43.060] (II) LoadModule: "record"
[ 43.060] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 43.061] (II) Module record: vendor="X.Org Foundation"
[ 43.061] compiled for 1.11.2, module version = 1.13.0
[ 43.061] Module class: X.Org Server Extension
[ 43.061] ABI class: X.Org Server Extension, version 6.0
[ 43.061] (II) Loading extension RECORD
[ 43.061] (II) LoadModule: "dri"
[ 43.061] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 43.063] (II) Module dri: vendor="X.Org Foundation"
[ 43.063] compiled for 1.11.2, module version = 1.0.0
[ 43.063] ABI class: X.Org Server Extension, version 6.0
[ 43.063] (II) Loading extension XFree86-DRI
[ 43.063] (II) LoadModule: "dri2"
[ 43.063] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 43.064] (II) Module dri2: vendor="X.Org Foundation"
[ 43.064] compiled for 1.11.2, module version = 1.2.0
[ 43.064] ABI class: X.Org Server Extension, version 6.0
[ 43.064] (II) Loading extension DRI2
[ 43.064] (II) LoadModule: "intel"
[ 43.091] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.114] (II) Module intel: vendor="X.Org Foundation"
[ 43.114] compiled for 1.10.99.902, module version = 2.16.0
[ 43.114] Module class: X.Org Video Driver
[ 43.114] ABI class: X.Org Video Driver, version 11.0
[ 43.114] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810,
i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G,
E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G,
965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45,
4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale,
Sandybridge Desktop (GT1), Sandybridge Desktop (GT2),
Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1),
Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+),
Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2),
Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server
[ 43.114] (++) using VT number 7
[ 43.134] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.135] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so
[ 43.135] Requested Entity already in use!
[ 43.135] (EE) Screen 1 deleted because of no matching config section.
[ 43.135] (II) UnloadModule: "intel"
[ 43.136] (II) Unloading intel
[ 43.136] drmOpenDevice: node name is /dev/dri/card0
[ 43.136] drmOpenDevice: open result is 8, (OK)
[ 43.136] drmOpenByBusid: Searching for BusID pci:0000:00:02.0
[ 43.136] drmOpenDevice: node name is /dev/dri/card0
[ 43.136] drmOpenDevice: open result is 8, (OK)
[ 43.136] drmOpenByBusid: drmOpenMinor returns 8
[ 43.136] drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0
[ 43.136] (**) intel(0): Depth 24, (--) framebuffer bpp 32
[ 43.136] (==) intel(0): RGB weight 888
[ 43.136] (==) intel(0): Default visual is TrueColor
[ 43.136] (II) intel(0): Integrated Graphics Chipset: Intel(R) Arrandale
[ 43.136] (--) intel(0): Chipset: "Arrandale"
[ 43.136] (**) intel(0): Relaxed fencing enabled
[ 43.136] (**) intel(0): Wait on SwapBuffers? enabled
[ 43.136] (**) intel(0): Triple buffering? enabled
[ 43.136] (**) intel(0): Framebuffer tiled
[ 43.136] (**) intel(0): Pixmaps tiled
[ 43.136] (**) intel(0): 3D buffers tiled
[ 43.136] (**) intel(0): SwapBuffers wait enabled
[ 43.136] (==) intel(0): video overlay key set to 0x101fe
[ 43.136] (II) intel(0): Output LVDS1 using monitor section Monitor0
[ 43.136] (**) intel(0): Option "Enable" "true"
[ 43.136] (II) intel(0): found backlight control interface /sys/class/backlight/acpi_video0
[ 43.196] (II) intel(0): Output VGA1 has no monitor section
[ 43.196] (II) intel(0): EDID for output LVDS1
[ 43.196] (II) intel(0): Manufacturer: BOE Model: 58e Serial#: 0
[ 43.196] (II) intel(0): Year: 2010 Week: 1
[ 43.196] (II) intel(0): EDID Version: 1.4
[ 43.196] (II) intel(0): Digital Display Input
[ 43.196] (II) intel(0): Undefined color depth
[ 43.196] (II) intel(0): Digital interface is undefined
[ 43.196] (II) intel(0): Max Image Size [cm]: horiz.: 31 vert.: 17
[ 43.196] (II) intel(0): Gamma: 2.20
[ 43.196] (II) intel(0): No DPMS capabilities specified
[ 43.196] (II) intel(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 43.196] (II) intel(0): First detailed timing is preferred mode
[ 43.196] (II) intel(0): Preferred mode is native pixel format and refresh rate
[ 43.196] (II) intel(0): redX: 0.574 redY: 0.335 greenX: 0.335 greenY: 0.585
[ 43.196] (II) intel(0): blueX: 0.154 blueY: 0.119 whiteX: 0.312 whiteY: 0.328
[ 43.196] (II) intel(0): Manufacturer's mask: 0
[ 43.196] (II) intel(0): Supported detailed timing:
[ 43.196] (II) intel(0): clock: 72.3 MHz Image Size: 309 x 173 mm
[ 43.196] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0
[ 43.196] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 790 v_border: 0
[ 43.196] (II) intel(0): Supported detailed timing:
[ 43.196] (II) intel(0): clock: 72.3 MHz Image Size: 309 x 173 mm
[ 43.196] (II) intel(0): h_active: 1366 h_sync: 1414 h_sync_end 1446 h_blank_end 1526 h_border: 0
[ 43.196] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 777 v_blanking: 790 v_border: 0
[ 43.196] (II) intel(0): KFDV9HT14101
[ 43.196] (II) intel(0): Unknown vendor-specific block 0
[ 43.196] (II) intel(0): EDID (in hex):
[ 43.196] (II) intel(0): 00ffffffffffff0009e58e0500000000
[ 43.196] (II) intel(0): 01140104801f11780a3fa09355559527
[ 43.196] (II) intel(0): 1e505400000001010101010101010101
[ 43.196] (II) intel(0): 010101010101411c56a0500016303020
[ 43.196] (II) intel(0): 360035ad1000001a411c56a050001630
[ 43.196] (II) intel(0): 3020360035ad1000001a000000fe004b
[ 43.196] (II) intel(0): 46445639814854313431303100000000
[ 43.196] (II) intel(0): 00004101940100000001010a20200000
[ 43.196] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 43.196] (II) intel(0): Printing DDC gathered Modelines:
[ 43.196] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 43.196] (II) intel(0): Not using default mode "320x240" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "400x300" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "512x384" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "640x480" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "640x512" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "800x600" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "896x672" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "928x696" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "960x720" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "700x525" (doublescan mode not supported)
[ 43.196] (II) intel(0): Not using default mode "1024x768" (doublescan mode not supported)
[ 43.196] (II) intel(0): Printing probed modes for output LVDS1
[ 43.196] (II) intel(0): Modeline "1366x768"x60.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 43.196] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 43.196] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 43.196] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 43.196] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 43.255] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 43.255] (II) intel(0): EDID for output VGA1
[ 43.255] (II) intel(0): Manufacturer: PHL Model: c02d Serial#: 9740
[ 43.255] (II) intel(0): Year: 2009 Week: 35
[ 43.255] (II) intel(0): EDID Version: 1.3
[ 43.255] (II) intel(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
[ 43.255] (II) intel(0): Sync: Separate
[ 43.255] (II) intel(0): Max Image Size [cm]: horiz.: 34 vert.: 19
[ 43.255] (II) intel(0): Gamma: 2.20
[ 43.255] (II) intel(0): DPMS capabilities: Off; RGB/Color Display
[ 43.255] (II) intel(0): First detailed timing is preferred mode
[ 43.255] (II) intel(0): redX: 0.635 redY: 0.335 greenX: 0.281 greenY: 0.597
[ 43.255] (II) intel(0): blueX: 0.153 blueY: 0.085 whiteX: 0.312 whiteY: 0.328
[ 43.255] (II) intel(0): Supported established timings:
[ 43.255] (II) intel(0): 720x400@70Hz
[ 43.255] (II) intel(0): 640x480@60Hz
[ 43.255] (II) intel(0): 640x480@67Hz
[ 43.255] (II) intel(0): 640x480@72Hz
[ 43.255] (II) intel(0): 640x480@75Hz
[ 43.255] (II) intel(0): 800x600@56Hz
[ 43.255] (II) intel(0): 800x600@60Hz
[ 43.255] (II) intel(0): 800x600@72Hz
[ 43.255] (II) intel(0): 800x600@75Hz
[ 43.255] (II) intel(0): 832x624@75Hz
[ 43.255] (II) intel(0): 1024x768@60Hz
[ 43.255] (II) intel(0): 1024x768@70Hz
[ 43.255] (II) intel(0): 1024x768@75Hz
[ 43.255] (II) intel(0): Manufacturer's mask: 0
[ 43.255] (II) intel(0): Supported standard timings:
[ 43.255] (II) intel(0): #0: hsize: 640 vsize 400 refresh: 70 vid: 2609
[ 43.255] (II) intel(0): #1: hsize: 1024 vsize 768 refresh: 72 vid: 19553
[ 43.255] (II) intel(0): Supported detailed timing:
[ 43.255] (II) intel(0): clock: 85.8 MHz Image Size: 344 x 194 mm
[ 43.255] (II) intel(0): h_active: 1366 h_sync: 1436 h_sync_end 1579 h_blank_end 1792 h_border: 0
[ 43.255] (II) intel(0): v_active: 768 v_sync: 771 v_sync_end 774 v_blanking: 798 v_border: 0
[ 43.255] (II) intel(0): Serial No: AU50935009740
[ 43.255] (II) intel(0): Monitor name: Philips 160E
[ 43.255] (II) intel(0): Ranges: V min: 56 V max: 76 Hz, H min: 30 H max: 60 kHz, PixClock max 86 MHz
[ 43.255] (II) intel(0): EDID (in hex):
[ 43.255] (II) intel(0): 00ffffffffffff00410c2dc00c260000
[ 43.255] (II) intel(0): 23130103682213782ab370a255489827
[ 43.255] (II) intel(0): 155054bfee00310a614c010101010101
[ 43.255] (II) intel(0): 0101010101017f2156aa51001e30468f
[ 43.255] (II) intel(0): 330058c21000001e000000ff00415535
[ 43.255] (II) intel(0): 30393335303039373430000000fc0050
[ 43.255] (II) intel(0): 68696c69707320313630450a000000fd
[ 43.255] (II) intel(0): 00384c1e3c08000a20202020202000c0
[ 43.255] (II) intel(0): Printing probed modes for output VGA1
[ 43.255] (II) intel(0): Modeline "1366x768"x60.0 85.75 1366 1436 1579 1792 768 771 774 798 +hsync +vsync (47.9 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x75.1 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync (60.1 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x72.0 78.44 1024 1080 1192 1360 768 769 772 801 -hsync +vsync (57.7 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x70.1 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync (56.5 kHz)
[ 43.255] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 43.255] (II) intel(0): Modeline "832x624"x74.6 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync (49.7 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x72.2 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync (48.1 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x75.0 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync (46.9 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 43.255] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x72.8 31.50 640 664 704 832 480 489 491 520 -hsync -vsync (37.9 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x75.0 31.50 640 656 720 840 480 481 484 500 -hsync -vsync (37.5 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x66.7 30.24 640 704 768 864 480 483 486 525 -hsync -vsync (35.0 kHz)
[ 43.255] (II) intel(0): Modeline "640x480"x60.0 25.20 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 43.255] (II) intel(0): Modeline "720x400"x70.1 28.32 720 738 846 900 400 412 414 449 -hsync +vsync (31.5 kHz)
[ 43.255] (II) intel(0): Output LVDS1 enabled by config file
[ 43.255] (II) intel(0): Output VGA1 connected
[ 43.255] (II) intel(0): Using exact sizes for initial modes
[ 43.255] (II) intel(0): Output LVDS1 using initial mode 1366x768
[ 43.255] (II) intel(0): Output VGA1 using initial mode 1366x768
[ 43.255] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated.
[ 43.255] (II) intel(0): Kernel page flipping support detected, enabling
[ 43.255] (**) intel(0): Display dimensions: (310, 170) mm
[ 43.255] (**) intel(0): DPI set to (111, 114)
[ 43.255] (II) Loading sub module "fb"
[ 43.255] (II) LoadModule: "fb"
[ 43.255] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 43.277] (II) Module fb: vendor="X.Org Foundation"
[ 43.277] compiled for 1.11.2, module version = 1.0.0
[ 43.277] ABI class: X.Org ANSI C Emulation, version 0.4
[ 43.277] (II) Loading sub module "dri2"
[ 43.277] (II) LoadModule: "dri2"
[ 43.277] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 43.277] (II) Module dri2: vendor="X.Org Foundation"
[ 43.277] compiled for 1.11.2, module version = 1.2.0
[ 43.277] ABI class: X.Org Server Extension, version 6.0
[ 43.277] (==) Depth 24 pixmap format is 32 bpp
[ 43.277] (II) intel(0): [DRI2] Setup complete
[ 43.277] (II) intel(0): [DRI2] DRI driver: i965
[ 43.277] (II) intel(0): Allocated new frame buffer 1408x768 stride 5632, tiled
[ 43.339] (II) UXA(0): Driver registered support for the following operations:
[ 43.339] (II) solid
[ 43.339] (II) copy
[ 43.339] (II) composite (RENDER acceleration)
[ 43.339] (II) put_image
[ 43.339] (II) get_image
[ 43.339] (==) intel(0): Backing store disabled
[ 43.339] (==) intel(0): Silken mouse enabled
[ 43.339] (II) intel(0): Initializing HW Cursor
[ 43.456] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message.
[ 43.466] (==) intel(0): DPMS enabled
[ 43.466] (==) intel(0): Intel XvMC decoder enabled
[ 43.466] (II) intel(0): Set up textured video
[ 43.466] (II) intel(0): [XvMC] xvmc_vld driver initialized.
[ 43.466] (II) intel(0): direct rendering: DRI2 Enabled
[ 43.466] (WW) intel(0): Option "Enable" is not used
[ 43.466] (WW) intel(0): Option "TwinView" is not used
[ 43.466] (==) intel(0): hotplug detection: "enabled"
[ 43.466] (--) RandR disabled
[ 43.466] (II) Initializing built-in extension Generic Event Extension
[ 43.466] (II) Initializing built-in extension SHAPE
[ 43.466] (II) Initializing built-in extension MIT-SHM
[ 43.466] (II) Initializing built-in extension XInputExtension
[ 43.466] (II) Initializing built-in extension XTEST
[ 43.466] (II) Initializing built-in extension BIG-REQUESTS
[ 43.466] (II) Initializing built-in extension SYNC
[ 43.466] (II) Initializing built-in extension XKEYBOARD
[ 43.466] (II) Initializing built-in extension XC-MISC
[ 43.466] (II) Initializing built-in extension SECURITY
[ 43.466] (II) Initializing built-in extension XINERAMA
[ 43.466] (II) Initializing built-in extension XFIXES
[ 43.466] (II) Initializing built-in extension RENDER
[ 43.466] (II) Initializing built-in extension RANDR
[ 43.466] (II) Initializing built-in extension COMPOSITE
[ 43.466] (II) Initializing built-in extension DAMAGE
[ 43.605] (II) AIGLX: enabled GLX_MESA_copy_sub_buffer
[ 43.605] (II) AIGLX: enabled GLX_INTEL_swap_event
[ 43.605] (II) AIGLX: enabled GLX_SGI_swap_control and GLX_MESA_swap_control
[ 43.605] (II) AIGLX: enabled GLX_SGI_make_current_read
[ 43.605] (II) AIGLX: GLX_EXT_texture_from_pixmap backed by buffer objects
[ 43.605] (II) AIGLX: Loaded and initialized i965
[ 43.605] (II) GLX: Initialized DRI2 GL provider for screen 0
[ 43.605] (II) intel(0): Setting screen physical size to 361 x 203
[ 43.909] (II) config/udev: Adding input device Power Button (/dev/input/event7)
[ 43.910] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 43.910] (II) LoadModule: "evdev"
[ 43.910] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.910] (II) Module evdev: vendor="X.Org Foundation"
[ 43.910] compiled for 1.10.99.902, module version = 2.6.0
[ 43.910] Module class: X.Org XInput Driver
[ 43.910] ABI class: X.Org XInput driver, version 13.0
[ 43.910] (II) Using input driver 'evdev' for 'Power Button'
[ 43.910] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.911] (**) Power Button: always reports core events
[ 43.911] (**) Power Button: Device: "/dev/input/event7"
[ 43.911] (--) Power Button: Found keys
[ 43.911] (II) Power Button: Configuring as keyboard
[ 43.911] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input7/event7"
[ 43.911] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 43.911] (**) Option "xkb_rules" "evdev"
[ 43.911] (**) Option "xkb_model" "evdev"
[ 43.911] (**) Option "xkb_layout" "us"
[ 43.931] (II) config/udev: Adding input device Video Bus (/dev/input/event15)
[ 43.931] (**) Video Bus: Applying InputClass "evdev keyboard catchall"
[ 43.931] (II) Using input driver 'evdev' for 'Video Bus'
[ 43.931] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.931] (**) Video Bus: always reports core events
[ 43.931] (**) Video Bus: Device: "/dev/input/event15"
[ 43.931] (--) Video Bus: Found keys
[ 43.931] (II) Video Bus: Configuring as keyboard
[ 43.931] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:01/input/input15/event15"
[ 43.931] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 43.931] (**) Option "xkb_rules" "evdev"
[ 43.931] (**) Option "xkb_model" "evdev"
[ 43.931] (**) Option "xkb_layout" "us"
[ 43.932] (II) config/udev: Adding input device Power Button (/dev/input/event4)
[ 43.932] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 43.932] (II) Using input driver 'evdev' for 'Power Button'
[ 43.932] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.932] (**) Power Button: always reports core events
[ 43.932] (**) Power Button: Device: "/dev/input/event4"
[ 43.932] (--) Power Button: Found keys
[ 43.932] (II) Power Button: Configuring as keyboard
[ 43.932] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4/event4"
[ 43.932] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 43.932] (**) Option "xkb_rules" "evdev"
[ 43.932] (**) Option "xkb_model" "evdev"
[ 43.932] (**) Option "xkb_layout" "us"
[ 43.932] (II) config/udev: Adding input device Lid Switch (/dev/input/event5)
[ 43.932] (II) No input driver/identifier specified (ignoring)
[ 43.932] (II) config/udev: Adding input device Sleep Button (/dev/input/event6)
[ 43.932] (**) Sleep Button: Applying InputClass "evdev keyboard catchall"
[ 43.932] (II) Using input driver 'evdev' for 'Sleep Button'
[ 43.932] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.932] (**) Sleep Button: always reports core events
[ 43.932] (**) Sleep Button: Device: "/dev/input/event6"
[ 43.932] (--) Sleep Button: Found keys
[ 43.932] (II) Sleep Button: Configuring as keyboard
[ 43.932] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6/event6"
[ 43.932] (II) XINPUT: Adding extended input device "Sleep Button" (type: KEYBOARD, id 9)
[ 43.933] (**) Option "xkb_rules" "evdev"
[ 43.933] (**) Option "xkb_model" "evdev"
[ 43.933] (**) Option "xkb_layout" "us"
[ 43.933] (II) config/udev: Adding input device HID 413c:8161 (/dev/input/event2)
[ 43.933] (**) HID 413c:8161: Applying InputClass "evdev keyboard catchall"
[ 43.933] (II) Using input driver 'evdev' for 'HID 413c:8161'
[ 43.933] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.933] (**) HID 413c:8161: always reports core events
[ 43.933] (**) HID 413c:8161: Device: "/dev/input/event2"
[ 43.933] (--) HID 413c:8161: Found keys
[ 43.933] (II) HID 413c:8161: Configuring as keyboard
[ 43.933] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.1/1-1.2.1:1.0/input/input2/event2"
[ 43.933] (II) XINPUT: Adding extended input device "HID 413c:8161" (type: KEYBOARD, id 10)
[ 43.933] (**) Option "xkb_rules" "evdev"
[ 43.933] (**) Option "xkb_model" "evdev"
[ 43.933] (**) Option "xkb_layout" "us"
[ 43.934] (II) config/udev: Adding input device HID 413c:8162 (/dev/input/event3)
[ 43.934] (**) HID 413c:8162: Applying InputClass "evdev pointer catchall"
[ 43.934] (II) Using input driver 'evdev' for 'HID 413c:8162'
[ 43.934] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.934] (**) HID 413c:8162: always reports core events
[ 43.934] (**) HID 413c:8162: Device: "/dev/input/event3"
[ 43.934] (--) HID 413c:8162: Found 3 mouse buttons
[ 43.934] (--) HID 413c:8162: Found relative axes
[ 43.934] (--) HID 413c:8162: Found x and y relative axes
[ 43.934] (II) HID 413c:8162: Configuring as mouse
[ 43.934] (**) HID 413c:8162: YAxisMapping: buttons 4 and 5
[ 43.934] (**) HID 413c:8162: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.934] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.2/1-1.2.2/1-1.2.2:1.0/input/input3/event3"
[ 43.934] (II) XINPUT: Adding extended input device "HID 413c:8162" (type: MOUSE, id 11)
[ 43.934] (II) HID 413c:8162: initialized for relative axes.
[ 43.934] (**) HID 413c:8162: (accel) keeping acceleration scheme 1
[ 43.934] (**) HID 413c:8162: (accel) acceleration profile 0
[ 43.934] (**) HID 413c:8162: (accel) acceleration factor: 2.000
[ 43.934] (**) HID 413c:8162: (accel) acceleration threshold: 4
[ 43.934] (II) config/udev: Adding input device HID 413c:8162 (/dev/input/mouse1)
[ 43.934] (II) No input driver/identifier specified (ignoring)
[ 43.934] (II) config/udev: Adding input device Laptop_Integrated_Webcam_0.3M (/dev/input/event10)
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: Applying InputClass "evdev keyboard catchall"
[ 43.934] (II) Using input driver 'evdev' for 'Laptop_Integrated_Webcam_0.3M'
[ 43.934] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: always reports core events
[ 43.934] (**) Laptop_Integrated_Webcam_0.3M: Device: "/dev/input/event10"
[ 43.934] (--) Laptop_Integrated_Webcam_0.3M: Found keys
[ 43.934] (II) Laptop_Integrated_Webcam_0.3M: Configuring as keyboard
[ 43.934] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input10/event10"
[ 43.934] (II) XINPUT: Adding extended input device "Laptop_Integrated_Webcam_0.3M" (type: KEYBOARD, id 12)
[ 43.934] (**) Option "xkb_rules" "evdev"
[ 43.934] (**) Option "xkb_model" "evdev"
[ 43.934] (**) Option "xkb_layout" "us"
[ 43.935] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event11)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device HDA Intel Mic at Ext Right Jack (/dev/input/event12)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device HDA Intel HP Out at Ext Right Jack (/dev/input/event13)
[ 43.935] (II) No input driver/identifier specified (ignoring)
[ 43.935] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 43.935] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 43.935] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 43.935] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.936] (**) USB OPTICAL MOUSE: always reports core events
[ 43.936] (**) USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 43.936] (--) USB OPTICAL MOUSE: Found 3 mouse buttons
[ 43.936] (--) USB OPTICAL MOUSE: Found scroll wheel(s)
[ 43.936] (--) USB OPTICAL MOUSE: Found relative axes
[ 43.936] (--) USB OPTICAL MOUSE: Found x and y relative axes
[ 43.936] (II) USB OPTICAL MOUSE: Configuring as mouse
[ 43.936] (II) USB OPTICAL MOUSE: Adding scrollwheel support
[ 43.936] (**) USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 43.936] (**) USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.936] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input1/event1"
[ 43.936] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 13)
[ 43.936] (II) USB OPTICAL MOUSE: initialized for relative axes.
[ 43.936] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 43.936] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 43.936] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 43.936] (II) No input driver/identifier specified (ignoring)
[ 43.936] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 43.936] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 43.936] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 43.936] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.936] (**) AT Translated Set 2 keyboard: always reports core events
[ 43.936] (**) AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 43.936] (--) AT Translated Set 2 keyboard: Found keys
[ 43.936] (II) AT Translated Set 2 keyboard: Configuring as keyboard
[ 43.936] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 43.936] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 14)
[ 43.936] (**) Option "xkb_rules" "evdev"
[ 43.936] (**) Option "xkb_model" "evdev"
[ 43.936] (**) Option "xkb_layout" "us"
[ 43.937] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/event14)
[ 43.937] (**) PS/2 Generic Mouse: Applying InputClass "evdev pointer catchall"
[ 43.937] (II) Using input driver 'evdev' for 'PS/2 Generic Mouse'
[ 43.937] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.937] (**) PS/2 Generic Mouse: always reports core events
[ 43.937] (**) PS/2 Generic Mouse: Device: "/dev/input/event14"
[ 43.937] (--) PS/2 Generic Mouse: Found 3 mouse buttons
[ 43.937] (--) PS/2 Generic Mouse: Found relative axes
[ 43.937] (--) PS/2 Generic Mouse: Found x and y relative axes
[ 43.937] (II) PS/2 Generic Mouse: Configuring as mouse
[ 43.937] (**) PS/2 Generic Mouse: YAxisMapping: buttons 4 and 5
[ 43.937] (**) PS/2 Generic Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 43.937] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio1/input/input14/event14"
[ 43.937] (II) XINPUT: Adding extended input device "PS/2 Generic Mouse" (type: MOUSE, id 15)
[ 43.937] (II) PS/2 Generic Mouse: initialized for relative axes.
[ 43.937] (**) PS/2 Generic Mouse: (accel) keeping acceleration scheme 1
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration profile 0
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration factor: 2.000
[ 43.937] (**) PS/2 Generic Mouse: (accel) acceleration threshold: 4
[ 43.937] (II) config/udev: Adding input device PS/2 Generic Mouse (/dev/input/mouse2)
[ 43.937] (II) No input driver/identifier specified (ignoring)
[ 43.937] (II) config/udev: Adding input device PC Speaker (/dev/input/event8)
[ 43.937] (II) No input driver/identifier specified (ignoring)
[ 43.938] (II) config/udev: Adding input device Dell WMI hotkeys (/dev/input/event9)
[ 43.938] (**) Dell WMI hotkeys: Applying InputClass "evdev keyboard catchall"
[ 43.938] (II) Using input driver 'evdev' for 'Dell WMI hotkeys'
[ 43.938] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 43.938] (**) Dell WMI hotkeys: always reports core events
[ 43.938] (**) Dell WMI hotkeys: Device: "/dev/input/event9"
[ 43.938] (--) Dell WMI hotkeys: Found keys
[ 43.938] (II) Dell WMI hotkeys: Configuring as keyboard
[ 43.938] (**) Option "config_info" "udev:/sys/devices/virtual/input/input9/event9"
[ 43.938] (II) XINPUT: Adding extended input device "Dell WMI hotkeys" (type: KEYBOARD, id 16)
[ 43.938] (**) Option "xkb_rules" "evdev"
[ 43.938] (**) Option "xkb_model" "evdev"
[ 43.938] (**) Option "xkb_layout" "us"
[ 48.392] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 48.392] (II) intel(0): Printing DDC gathered Modelines:
[ 48.392] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 48.456] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 48.457] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 48.457] (II) intel(0): Printing DDC gathered Modelines:
[ 48.457] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 48.517] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 49.976] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 49.976] (II) intel(0): Printing DDC gathered Modelines:
[ 49.976] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 50.035] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 213.440] (II) config/udev: removing device USB OPTICAL MOUSE
[ 213.440] (II) USB OPTICAL MOUSE: Close
[ 213.440] (II) UnloadModule: "evdev"
[ 213.440] (II) Unloading evdev
[ 213.728] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/event1)
[ 213.728] (**) USB OPTICAL MOUSE: Applying InputClass "evdev pointer catchall"
[ 213.728] (II) Using input driver 'evdev' for ' USB OPTICAL MOUSE'
[ 213.728] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 213.728] (**) USB OPTICAL MOUSE: always reports core events
[ 213.728] (**) USB OPTICAL MOUSE: Device: "/dev/input/event1"
[ 213.728] (--) USB OPTICAL MOUSE: Found 3 mouse buttons
[ 213.728] (--) USB OPTICAL MOUSE: Found scroll wheel(s)
[ 213.728] (--) USB OPTICAL MOUSE: Found relative axes
[ 213.728] (--) USB OPTICAL MOUSE: Found x and y relative axes
[ 213.728] (II) USB OPTICAL MOUSE: Configuring as mouse
[ 213.728] (II) USB OPTICAL MOUSE: Adding scrollwheel support
[ 213.728] (**) USB OPTICAL MOUSE: YAxisMapping: buttons 4 and 5
[ 213.728] (**) USB OPTICAL MOUSE: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 213.728] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.1/2-1.1:1.0/input/input16/event1"
[ 213.728] (II) XINPUT: Adding extended input device " USB OPTICAL MOUSE" (type: MOUSE, id 13)
[ 213.728] (II) USB OPTICAL MOUSE: initialized for relative axes.
[ 213.728] (**) USB OPTICAL MOUSE: (accel) keeping acceleration scheme 1
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration profile 0
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration factor: 2.000
[ 213.728] (**) USB OPTICAL MOUSE: (accel) acceleration threshold: 4
[ 213.730] (II) config/udev: Adding input device USB OPTICAL MOUSE (/dev/input/mouse0)
[ 213.730] (II) No input driver/identifier specified (ignoring)
[ 1627.253] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1627.253] (II) intel(0): Printing DDC gathered Modelines:
[ 1627.253] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1627.311] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1644.964] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1644.964] (II) intel(0): Printing DDC gathered Modelines:
[ 1644.964] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.027] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.042] (II) intel(0): Allocated new frame buffer 2752x768 stride 11264, tiled
[ 1645.230] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.230] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.230] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.289] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.307] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.307] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.307] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.365] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.387] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.387] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.387] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.446] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 1645.447] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 1645.447] (II) intel(0): Printing DDC gathered Modelines:
[ 1645.447] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 1645.505] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
[ 2335.972] (II) intel(0): EDID vendor "BOE", prod id 1422
[ 2335.972] (II) intel(0): Printing DDC gathered Modelines:
[ 2335.972] (II) intel(0): Modeline "1366x768"x0.0 72.33 1366 1414 1446 1526 768 771 777 790 +hsync -vsync (47.4 kHz)
[ 2336.030] (WW) EDID timing clock 85.75 exceeds claimed max 85MHz, fixing
lspci output
00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 02)
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 02)
00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06)
00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 05)
00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 05)
00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 05)
00:1c.2 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 3 (rev 05)
00:1c.4 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 (rev 05)
00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 05)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a5)
00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 05)
00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 05)
00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 05)
00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 05)
12:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
13:00.0 Ethernet controller: Atheros Communications AR8152 v2.0 Fast Ethernet (rev c1)
ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02)
ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02)
ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02)
ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02)
ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02)
ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02)

No one? I have the exact same problem. MSI x360 laptop, intel onboard graphics. I too use xrandr. I've seen elsewhere that windows users have solved this by turning off GPU overclocking. Maybe this can point us in the right direction?

X1 Carbon Gen 3 - maximum external display configuration?

Similar Messages

Maybe you are looking for