X130e / X131e configuration changes

Hi, I'm an avid user of X series TP's, namely X220 and X230. These are terrific for being able to make changes with RAM, SSD, batteries and network cards. I want to try using the smaller brother of these, the X130e or X131e, and wondering if I'd be able to change HDD and WAN or WiFi cards. Any ideas???
Moderator comment: Subject edited to match content.
Solved!
Go to Solution.

Hello,
I have an X120e, which is a generation or two earlier than the models you are asking about (X100e, X120e, X121e, X130e, X131e) and while CPU performance is certainly not in the same range as my i7-equipped X220, it performs quite well, especially since I have replaced the hard disk drive to a solid state drive and added more RAM.
If you are looking for a sub-12" netbook-sized computer which is capable of handling basic office productivity software (i.e., Microsoft Office) and maybe some light gaming, the X1nne series is going to be hard to beat.
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Similar Messages

Help me configure Change request management !!!

Dear friends,
I am Going to Configure Change request Management, so just to ensure that the configuration is not erronous, i would need Expert advise..
Just want to know Clear few things before i proceed..
I am also refering SPRO and related notes
Scenario :
I have two SYSTEMS SAP ECC 6.0 with System id R03 and Soluiton manager with SYSTEM id SOL,
R03 has 3 clients, 300 600 700..
In R03 300 is the development client, 600 is quality client, 700 is the production client.
SOL has 2 clients, 100, 200
With 200 as the production client.
Q.1) Do i have to configure CHARM in both the client (100 and 200 of SOLMAN).
Q.2) Initially I had tried to set CHARM in client 100 of solman, but later on realized that it has to be set up in client 200.
When i logon to client 200 and Execute IMG activity Spro-> sap soltion manger->basic settings-> sap solution manager system->activate integration with change request management.
Then by default it take the previous client ( client 100) as the change request management client.
( as we know there are three steps in the above activity ), the other activity are executed properly, only prblem being that the default client is always set to 100, which should not be the case).
I do get the prompt saying ( "The change request clent is set to clent 100, do u want to change to client 200, on clicking yes, still it is always set the same client 100 as charm client ")
Plz let me know what do i do to set the change request client to 200??
Q.3) Regarding TMS, we have local domain controller in solman and local domain in R3.
We are planing to establish domain links between the two systems( ie both the domain controllers) ??
Is this the right strategy ??
Any other method that u can recommend ??
Q.4)One of the IMG activity says, Generate Destinations to client 000 of all the domain controllers..
Whenever i do this these, destinations are created with errors, i am not able to create trusted RFC destinations without errors.
When i logon to satellite domain controler and excecute sm59 there are 2 destinations created Trusted and BACK.
These destinations works well,
but when i logon to Solman, got to sm59 , when i test the TMW and TRUSTED rfc destinations i test these destinations using Remote Logon i get error,
" no authorization to logon as trusted system"
I went thru one note which recomended Kernel upgrades to solve the problem,
I r3 my kernel relaese is 700 with patch level 56, the note recomends to apply patch 80, did u have these problems??
what is your kernel patch levels in sateliite and solman systems.
Q.5) TO be able to raise tickets from R3 to solman we create RFC destinations.
We also create RFC destinations to client 000 of all the sateliite system,
dont u think these RFC destinations might interfere with each other??
Q.6) Is there anyone who has successfully configured CHARM. Can you plz share the configuration documents with me..
Please note :
All the contributors would be handesomely rewarded with points .

Hi,
Check this
Note 128447 - Trusted/Trusting Systems
For your Q4.
Q3.)
Establishing Domain link - That's the right way. Go ahead.
These are the steps.
1.Define Transport Routes for System Landscape
assign exactly one development system to a production system, and that these two systems are connected by exactly one unique transport track. If a development system and a production system are connected by more than one transport track, this may lead to inconsistencies within the transport distribution. This type of transport configuration cannot be supported by Change Request Management, and may cause inconsistencies within the tools involved.
2. Activate Extended Transport Control
The CTC parameter should be '1'
3.Configure Transport Strategy
Deactivate the QA Approval.
4. Activate Trusted Services.
5.Activate Domain Links.
You have to activate domain link between systems.
6. Generate RFC Destinations to Client 000
Hope this helps.
feel free to revert back.
--Ragu

Logging CRS configuration changes

Hallo,
in a 10.1 RAC environment,
is there a file which logs CRS configuration changes, like issuing a oifcfg -setif command?
Thx

Yes

Anyone Seen this Message Before "Configuration changes for domain saved to the repository."

I'm running into this situation where one of my WLS servers is generating the following
messages "Configuration changes for domain saved to the repository." This process
of saving to a repository is causing an issue on start-up. Typically my deployments
take 2-3 minutes on start-up. They are now taking 10 minutes. I've made no changes
to my application. I've been able to identify that this process of saving to a
repository is the main issue of contention....
Anyone know what the message means? Anyone know how to disable this message?

This is just WebLogic writing back changes to config.xml, which it does from time
to time for reasons like:
- your app deployment has changed.
- you've reconfigured something in the console.
etc...
WebLogic just spins this off into a handy execute thread, so it would be surprising
if this was causing your app deployment to slow down (how do you know it is).
In my experience, slower than normal app deployments are usually down to:
- waiting for database connections.
- waiting for connecitons to other external resources.
Remember (in WLS6.x anyway) initialisation is done serially on the main thread,
so if something's slow, everything gets blocked behind it.
simon.
I'm running into this situation where one of my WLS servers is generatingthe following
messages "Configuration changes for domain saved to the repository."This process
of saving to a repository is causing an issue on start-up. Typicallymy deployments
take 2-3 minutes on start-up. They are now taking 10 minutes. I'vemade no changes
to my application. I've been able to identify that this process ofsaving to a
repository is the main issue of contention....
Anyone know what the message means? Anyone know how to disable thismessage?

How to prevent BGP code 6 (Cease) subcode 6 (Other Configuration Change)

Can anyone tell How to prevent BGP code 6 (Cease) subcode 6 (Other Configuration Change) ?
We are facing frequent problem with this error. Please suggest how to stop this....
Note :- We are using BGP VPN between this peers.
Logs :
Date/Time : 2015-04-30 00:49:40+05:30
State : Up
Date/Time : 2015-04-30 00:39:05+05:30
State : Down
Error Code : 6(CEASE)
Error Subcode : 6(Other Configuration Change)
Notification : Send Notification
Date/Time : 2015-04-29 18:22:11+05:30
State : Up
Date/Time : 2015-04-29 18:21:39+05:30
State : Down
Error Code : 6(CEASE)
Error Subcode : 6(Other Configuration Change)
Notification : Send Notification

on the same dates you mean the same request are posted in IT2001? ie both full days?
Please clarify
usually the Time collision checks are followed only via posting using report rptarqpost and not while applying through portal in ESS
This is very strange you indicate
SO you need to check the basic tables first
You may need to check the collision.
Collisions Tables V_T554Y and V_554Y_B reaction indicators.
and V_T508A
able T582A set to time constraint of "Z
In backend Pa30 collision works like this
1) the logical collision, checks if there is an overlap in the validity
interval of the IT´s (begda, endda).
2) the physical collision, checks if there is an overlap in the time
interval of the IT's.
In the logical collision it is checked if there is an overlap in the
validity interval if at least one of the records is a full-day
( that is the case when you enter a Daily Work Schedule (DWS) )
So when one of the records has a DWS it is considered to be a full day
record and the logical collision is taken into consideration.
If instead you enter the only the time interval manually the records
are considered to be partial-day and the physical collision is
performed. In that case only the time interval is important.
So if the clock times are not entered the physical collision can not
take place.
The collision functionality is always based on clock times and dates,
never on the total nr of hours.
Edited by: Siddharth Rajora on Sep 21, 2011 4:57 PM

X121e bios loop : "configuration changed - restart the system"

After changing some settings in BIOS i got stuck in a reboot - loop.
* Cannot access the BIOS any more - pressing F1 changes the message to "Entering BIOS Setup Utility" followed by the message "configuration changed - restart the system"
* F12 changes the message to "Preparing Boot Device List" followed by "configuration changed - restart the system" and the system reboots again.
* Tried to remove the battery, pressing the power button for 10-15 sec. and reboot with AC Adapter connected
* Tried to remove the battery and unplug the bios battery for 3 days the reset the bios - doesn't work
* Tried to boot via USB (BIOS update, FreeDOS with BIOS update, Ubuntu-Live-USB) - nothing worked .. didn't change the boot-order - i always prefer USB boot
* Removing hard-disk produces the message "no operating system found"
Are there any tricks for resetting the BIOS to defaults, flashing BIOS without booting from USB?
see
* http://forums.lenovo.com/t5/ThinkPad-Edge-S-series/E-325-bios-settings-changed-keeps-rebooting/td-p/...
* http://forums.lenovo.com/t5/X-Serie-ThinkPad-Notebooks-inkl/x121e-Configuration-changed-Restart-Syst...
- there are several people with this issue ...

In service center they said that motherboard is glitchy and needs replacement.
So it was a hardware fault.

How to set up 'Tansport Request' to move Configuration Change to Prod ?

I would like to know the steps to transport the Configuration Changes from Development to QA (or Production).
Thanks for your help.

Hi Oscar,
Request are of two types.
1.Customization Request.( functional Consultants)
2.Workbench Request( Abapers)
If you are doing any configuration change using you user id in Devlopment system.
1.while saving the changes it will ask for customizing Request, here you have to give the request and save the changes.
if you want to move the changes from Development System to Qualtity.
Goto Transaction SE09 or Se10 give your user id name then Click on Display
Here Go to your Request No.xxxxxxxx and Click the Tranfort Icon/Bus Icon or Press F9.then the changes will be moved to Quality System.
Please ensure that Task will be released first.
Hope this clarifies your doubts and Please Reward If Really Helpful,
Thanks and Regards,
Sateesh.Kandula

Making a configuration change without using admin console

I am using the Platform Edition of App Server 7 so I don't have access to the web-based admin console.
I need to make a configuration change and the only directions I have are for the admin console.
Can anybody give me some pointers on what file to edit to acomplish the procedure below?
8. Log in to the Sun ONE Application Server administration console.
9. Select the application server Instance on which you installed the Identity Server.
10. Click JVM Settings and then JVM Options.
11. In the JVM Option field, enter the following string: -Dhttp.keepAlive=false
12. Click Add and then Save.

I think I've found it...
The file is server.xml and it is located at:
/var/opt/SUNWappserver7/domains/domain1/server1/config
There is a section under <java-config> with about 14 lines containing various <jvm-options>
I'll try adding this directive to the end of the <jvm-options> as follows:
<jvm-options>-Dhttp.keepAlive=false</jvm-options>

Configuration changes in long cycle orders

Hi,
We are currently working on with ETO client and have a scenario where Orders are configured using guided selling which triggers multiple child models as required. Each of these child models are connected to each other but can be manufactured and shipped separately. Order life cycle could range from 2 month to one year and changes are quite frequent. We would like to know the best practices we can adopt in configurator change management after booking in such large BOMs?
Thanks
Greg

Hi,
The code looks fine. To check whether the role still gets shutdown or not, you can handle the role's Stopping event, and write some messages to, say, table storage. Then if you see the message in table storage, it means the role has been restarted. Also please
try to write some messages in the Changing event to check whether your event handler is called.
Best Regards,
Ming Xu
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

What are configuration changes in billing?

what are configuration changes in billing
regards
[email protected]

hi
mail sent check uour mail
reward if useful
prashanth

Is there a way to restart my Java cloud service? What are "non-dynamic configuration changes"?

I am trying to deploy an ADF application to my trial instance of Java cloud, I am getting the following error:
2013-10-15 08:24:18 CDT: Deploy Application started
2013-10-15 08:24:19 CDT: weblogic.management.DeploymentException: [Deployer:149189]An attempt was made to execute the 'deploy' operation on an application named 'xyzAPP' that is not currently available. The application may have been created after non-dynamic configuration changes were activated. If so, the operation can not be performed until server is restarted so that the application will be available.
2013-10-15 08:24:19 CDT: WL action state: failed
2013-10-15 08:24:19 CDT: Action FAILED with WL action state: failed
2013-10-15 08:24:19 CDT: Check the server log of your Java cloud service for more info about the failure.
There are tutorials available for deploying your first ADF app to the cloud, which I followed carefully. Except for one thing, the ADF app was originally developed in Jdeveloper 11.1.2.4 and then migrated to 11.1.1.6. Could that be what is causing the problem? How can I try to troubleshoot this?

Hi,
You will have to raise an sr towards the hosting team to perform the restart.
Kind regards,
Flori

How to load the boot menu using the command line , after the configuration change ?

how to load the boot menu using the command line , after the configuration change ?

Hi @Bask-48
Welcome to the HP Forums!
It is a terrific place to find answers.
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
I grasp you are trying to change the boot order. Here is a link to Configuring the Boot Order in the System BIOS
that will assist you.
Good Luck and Happy Holidays!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Configuration archive after configuration change

Hello,
I'm assuming this can work with switches, routers, and controllers. I'm running PI 2.1 and am trying to get the configuration archive functionality working. I have both of these options checked under System Settings > Configuration Archive:
:: Archive configuration out-of-box
:: Archive configuration on receiving configuration change events
On the IOS device, these settings were configured for syslog/snmp:
logging buffered 100000
no logging event link-status
logging trap notifications
logging facility local6
logging source-interface Loopback0
logging <Prime IP>
snmp-server community ***** RW 13
snmp-server enable traps config
snmp-server enable traps syslog
snmp-server host <Prime IP> version 2c *****
I do not see any syslog messages in PI under alarms/alerts and the configuration never gets archived. I haven't run tcpdump yet to determine if PI is receiving these traps but I was hoping it was something simple I was overlooking. Thanks for any assistance that can be provided.

Thank you for the reply. To answer your question, yes. Community information matches with PI credentials.
I actually did get it to work yesterday. I did original testing on a 1921 router which is still not working, but when I tried configuring the same information on some switches (3750's) it worked. I thought routers would be configured the same - are there hardware limitations to this?
I look in the built-in CLI template 'Configure Logging' in PI and it only has switches and WLCs as available devices to push out to but I don't know what to make of it.

[TP x120e] Continuous "Configuration changed - Restart the system." error

I played with my bios (disabled/enabled mic, webcam, LAN and so), but after exiting the bios, Thinkpad x120e reboots continuously with the error message "Configuration changed - Restart the system.". I was not able to boot from any USB/HDD and also I can not enter to the BIOS. Hard bios reset won't help. Any ideas?
Thanks!

Hello,
Have you tried unplugging all power, including the internal CMOS/RTC backup battery, from the ThinkPad X120e, leading the unit alone for a few minutes to let any capacitors holding a residual electic charge drain, holding down the power button for 30 seconds to complete the operation, then plugging in the AC charger without either of the batteries installed, then holding down the F1 key while pressing the power button to see if that gets you into the BIOS settings?
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество

Configuration changes of "Classic to Standalone scenario" in EBP system

Hi,
Could you guide me in configuration changes of "Classic to Standalone Scenario" in EBP system...
Will I get any documentation on this..?
Thank you...
Best Regards,
Thiru

Hi Thiru,
to change from Classic to Standalone Scenario, you have to change customizing point "Define backend for product category".
If your set target system = SRM logical system, then follow on doc will be created localy in SRM -> standalone scenario.
Rgds
Christophe
PS: please reward points for helpfull answers

X130e / X131e configuration changes

Similar Messages

Maybe you are looking for