X201 Windows 8.1 Keyboard driver issue

I tried clean installing Windows 8.1 on my ThinkPad X201T
The Windows itself installs without any issue, but for some reason the keyboard drivers seem to be out of order. They will either not load up at all, or take incredibly long time to load up.
I've tried endless versions of Drivers, but none of them works to me. Newest drivers just don't work at all, and very old, early Windows 7 drivers and Vista-era drivers also have some problems.
Is there anyone who has successfuly set up Windows 8.1 and the drivers on ThinkPad X201, or other ThinkPads with 1st Gen Core i processor?
Kim
W540( ), Helix(Sold), Tablet 2(Sold) Tablet 2( ), X120e(Sold), X201 Tablet, X41 Tablet(Sold), X41, X32*4, 701C*4

Similar Messages

Windows 8.1 BSoD & driver issue

Hello,
I was hoping someone could help me out here. Let me describe the issue. For quite a while I was using Windows 8.1 fine and did not have any problems, however I recently burned my PSU somehow and then the problems started. Which I somewhy find odd, cause the
BSoD's are related to a driver issue(?). The driver which seems to cause the problem, is
Intel(R) Engine Management Interface.
"This device cannot start. (Code 10)
A device which does not exist was specified"
Event Viewer displays the following error:
"Intel(R) Engine Management Interface driver has failed to perform a handshake with the Firmware."
Since it says "A device which does not exist was specified.", I assume I don't need this driver at all, so I tried disabling it and uninstalling, but it keeps coming back every time I restart my PC. I even tried looking for a newer driver, but couldn't
find anything. The newest driver is for Windows 7 x64/x86. I found out you could possibly disable it in bios, but I couldn't find the option to do so in my bios. I went thru every option 1 by 1, just to make sure, I wouldn't miss it.
Here's my PC:
Motherboard: Gigabyte GA-H55M-S2 (F4 BIOS)
CPU: Intel i3 540 @ 3.07GHz (Overclocked to 4,03GHz)
Cooler: Cooler Master Hyper 212 EVO
GPU: NVIDIA GeForce GTX 660 (GV-N660OC-2GD)
RAM: 2 x Kingston 4GB 1333MHz DDR3
HDD: Western Digital 500GB
At the very moment, I have installed a fresh copy of Windows 8.1 Professional x64 and the problem still seems to exist. I have tried and googled for everything I can think off, now I'm just stuck at this problem.
I hope someone can help me out here, or at the very least, guide me in the right direction.
Link to minidump: http://1drv.ms/1H6E4uh

Use !analyze -v to get detailed debugging information.
BugCheck D1, {fffff8012d4359f0, 2, 8, fffff8012d4359f0}
Probably caused by : ntkrnlmp.exe ( nt!KiPageFault+23a )
Followup: MachineOwner
2: kd> !analyze -v
* Bugcheck Analysis *
DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1)
An attempt was made to access a pageable (or completely invalid) address at an
interrupt request level (IRQL) that is too high. This is usually
caused by drivers using improper addresses.
If kernel debugger is available get stack backtrace.
Arguments:
Arg1: fffff8012d4359f0, memory referenced
Arg2: 0000000000000002, IRQL
Arg3: 0000000000000008, value 0 = read operation, 1 = write operation
Arg4: fffff8012d4359f0, address which referenced memory
Debugging Details:
READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80108f64138
unable to get nt!MmNonPagedPoolStart
unable to get nt!MmSizeOfNonPagedPoolInBytes
fffff8012d4359f0
CURRENT_IRQL: 2
FAULTING_IP:
+8c228a89b114
fffff801`2d4359f0 ?? ???
CUSTOMER_CRASH_COUNT: 1
DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT
BUGCHECK_STR: AV
PROCESS_NAME: svchost.exe
ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
TRAP_FRAME: ffffd00027a58120 -- (.trap 0xffffd00027a58120)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=0a00000000000020 rbx=0000000000000000 rcx=0000000000000002
rdx=fffff8012d4359f0 rsi=0000000000000000 rdi=0000000000000000
rip=fffff8012d4359f0 rsp=ffffd00027a582b0 rbp=0001da10001da171
r8=00000000001da130 r9=02200000001da347 r10=7100a1ef05420000
r11=0000000000000042 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei ng nz na po nc
fffff801`2d4359f0 ?? ???
Resetting default scope
LAST_CONTROL_TRANSFER: from fffff80108d5d4e9 to fffff80108d519a0
FAILED_INSTRUCTION_ADDRESS:
+8c228a89b114
fffff801`2d4359f0 ?? ???
STACK_TEXT:
ffffd000`27a57fd8 fffff801`08d5d4e9 : 00000000`0000000a fffff801`2d4359f0 00000000`00000002 00000000`00000008 : nt!KeBugCheckEx
ffffd000`27a57fe0 fffff801`08d5bd3a : 00000000`00000008 ffffe000`8f89b0f8 00000000`00000000 00000000`00000000 : nt!KiBugCheckDispatch+0x69
ffffd000`27a58120 fffff801`2d4359f0 : 00000000`00000000 00000000`00000000 00000000`000e293f 00000000`00000000 : nt!KiPageFault+0x23a
ffffd000`27a582b0 00000000`00000000 : 00000000`00000000 00000000`000e293f 00000000`00000000 00000000`0001358b : 0xfffff801`2d4359f0
STACK_COMMAND: kb
FOLLOWUP_IP:
nt!KiPageFault+23a
fffff801`08d5bd3a 440f20c0 mov rax,cr8
SYMBOL_STACK_INDEX: 2
SYMBOL_NAME: nt!KiPageFault+23a
FOLLOWUP_NAME: MachineOwner
MODULE_NAME: nt
IMAGE_NAME: ntkrnlmp.exe
DEBUG_FLR_IMAGE_TIMESTAMP: 54c832b2
IMAGE_VERSION: 6.3.9600.17668
BUCKET_ID_FUNC_OFFSET: 23a
FAILURE_BUCKET_ID: AV_CODE_AV_BAD_IP_nt!KiPageFault
BUCKET_ID: AV_CODE_AV_BAD_IP_nt!KiPageFault
ANALYSIS_SOURCE: KM
FAILURE_ID_HASH_STRING: km:av_code_av_bad_ip_nt!kipagefault
FAILURE_ID_HASH: {73cd60cc-83fa-6b76-df08-1961c31d7403}
Followup: MachineOwner
It points to incorrect memory page access obviously. It generally caused by some driver like you found. update all drivers should be resolved. Have you tried ever?

IPhone 5 iOS 6.1.4 and Windows 7 x64 USB Driver Issues

Been pulling my hair out with this one for the last week or so and haven't had any luck finding anything on the forums or the web regarding a solution short of a full reinstall of Windows 7 which I am not prepared to do at this time; so hoping someone here can shine some light on this for me
I have a iPhone 5 that is updated to iOS 6.1.4 and a recently built Windows 7 64-bit machine. All of my other USB devices function fine (keyboard, mouse, Xbox 360 wireless receiver for Windows, and a Seagate 2TB external USB drive). I've downloaded the most recent version of iTunes, installed successfully and then attempt to plug in my phone to sync. I get the standard Windows *ding* that I've attached a device and 1 of 2 things happens (I haven't been able to determine what causes one reaction to happen versus the other): Windows will successfully install the 'Apple USB Mobile Device Driver' successfully and it will appear under my USB devices in Device Manager. However - iTunes will not recognize the phone and I cannot see it in Windows either. In the 'Devices and Printers' snap-in my iPhone will appear under 'Unspecified Devices' as the 'Apple USB Mobile Device'. The iTunes diagnostics fail to find a connected device so the tests fail. As soon as I unplug the device, the strangest thing happens: Windows will start trying to install a device driver and after a few seconds it will fail stating that the "MTP Device Driver" installation failed because the device was unplugged. iTunes also thrown an error "iTunes cannot connect to this iPhone" throwing error code 0XE8000065 (I've also seen error code 0XE8000085 as well)
After some finagling, I've managed to get Windows to recognize the device under 'Portable Devices' in Device Manager as an "MTP USB Device" using the generic driver. At this point, I've tried updating the driver and manually specifying the Apple USB driver located in the C:\Program Files(x86)\Common Files\Apple\Mobile Device Drivers which updates successfully but then changes the device to "Apple USB Mobile Device" and moves it under the USB Devices in Device Manager; and Windows nor iTunes can see it even still.
I've tried removing iTunes several times and ensuring that all remnants of the installation are gone (registry and folders on the installation drive) and have disconnected all my USB devices short of the keyboard and mouse and still I get the same results. At this point, I'm afraid that a re-install of Windows is going to be the solution; but it's a drastic one (I have a SSD drive where Windows is installed along with all of my games for faster load times/better performance and do not want to have to redownload\reinstall all of them) and I'm not prepared to undertake it at this time, which is why I'm posting here
I've used a utility called USBDeview that sees my phone is connected - so I know from a functional standpoint that my USB ports are good and working. I also know the cable is good too - my daughter's PC (Windows 7 32-bit with NO iTunes) immediately sees the device when I plug it in, installs the drivers, recognizes it as an iPhone and I can then see/browse it in Windows Explorer like I would normally expect. My work PC (Windows 7 64bit, NO iTunes) sees the device just fine as well. I would immensely appreciate anyone that has seen this issue or has any additional solutions I can try.
It's also worth mentioning that I've never used Kapersky antivirus so the UPPERFILTERS value in the registry that I've seen as a solution on some forums is not present on my machine. I'm using Microsoft Security Essentials as my antivirus (no flaming please lol - it meets my needs and is extremely lightweight, which is why I'm using it on a gaming rig) and it's not indicating any issues. I've also tried running iTunes as an administrator (even though my account is a local admin on the machine) and that does not have any effect either.
If there is anything I left out, please let me know; and I thank you in advance!

AphexTwin wrote:
- no Apple input?
Of course not. Didn't you bother to read the TOU of this forum? This is a USER TO USER technical support forum. Apple doesn't post here.

USB Trackpoint Keyboard Driver Issues

Hello!
I'm not entirely sure how to go about reporting bugs in drivers, so I decided this would be the best venue. I've discovered two bugs in the driver for the USB trackpoint keyboard. I'm using version 1.01 of the driver (available here: http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-73235) under Windows 7.
1.) There appears to be a memory leak somewhere. When I've been using the keyboard for a while, memory usage of Skd8855.exe climbs and climbs. I took a screenshot of it at 896 MB (http://toastsoft.net/usbkeyboarddriver.png) I've found that by killing Skd8855.exe and preventing it from loading on startup, most of the keyboard functions work properly. You don't get status lights on anything but caps lock, but overall seems to be functional.
2.) The trackpoint scrolling doesn't seem to work in Opera 10. If it does work, it will scroll for a second before the window loses focus and scrolling stops.
If I'm using the wrong driver or have neglected to install something else, I would appreciate any pointers in the right direction. If these are genuine bugs, I hope they get to the right place! And sorry if this isn't that place.

I am having the same exact issue on a 64bit Win 7 machine. Oddly enough i cancelled the exe in processes and the keyboard still works fine.

X1 Carbon - Windows 8.1 - Synaptic driver issue

Hello,
I did a fresh install of Windows 8.1 Enterprise and I am having an issue with the Synaptic UltraNav driver. I am using the latest driver from Lenovo (16.2.19.13 which says it supports 8.1). The issue is with gestures not working. When I go to the Mouse Properties from Control Panel I receive the message " Unable to connect to the Synaptics Pointing Device Driver". I can go to the UltraNav tab still, under TrackPad all gestures are disabled. If I check a box to enable one it will automatically uncheck itself. I can reopen the Mouse Properties over and over and eventually I will not receive the failed to connect message and can set gestures. At this point everything works, until I reboot.
Any ideas? Thanks in advanced.
Solved!
Go to Solution.

Hi Akohit,
Welcome to Lenovo Community Forums!
I'm sorry to hear that you are having issues with Synaptics driver in your Lenovo X1 carbon.
The first thing you will need to do is to remove the UltraNav driver from the system. In the Device Manager, select Mice and other pointing devices, and then right-click on the UltraNav device and select Uninstall. Make sure you check “Delete the driver software for this device” checkbox. Follow the prompts to uninstall and then restart when prompted by Windows. Windows should install a generic driver that will allow you to use the Touchpad.
Now try installing the generic Synaptics driver for your machine and see if helps to resolve your concern.
Best regards,
Mithun.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

HP Business Inkjet 1000/1100 Windows 7/Server 2003 Driver Issues

Hi, wondering if anyone can help.
We are having problems with Windows 7 32-bit printer drivers and our print server which is on Server 2003, the printers concerned are a HP Business Inkjet 1000 and 1100. We have VMWare installed on our clients running Windows 7, I can add the printers locally onto any vdi desktop using the driver pre-installed on Windows 7 and it can print perfectly with both of those printers. I installed the same driver onto our print server, tried two ways, first I connected to the server through Print Management and updated the driver from one of our Windows 7 clients (which is how I've been instructed to do) and I've also tried finding the local printer on my Windows 7 desktop while logged in Server 2003, both ways appear to installed the driver with no errors but when you go to print it just prints 3 blank sheets no matter what you print, it even does this for the test page, also the Printing Defaults under the Advanced tab keep resetting themselves, it's not applying any changes I make.
I'm failing to understand how the driver can appear to work when installed locally on the desktop but when it drags it from Server 2003 it's not printing correctly when in essence it is the exact same driver .... is Server 2003 not liking the fact it's a Windows 7 driver?
I am using the HP Business Inkjet 1000 driver in-box on Windows 7 Enterprise for both printers. The reason I'm using this driver is because the XP version of this driver which we had on our print server would print but would not print out certain graphics and symbols when printing from Windows 7.
Anyone else had similar issues?
Any help will be appreciated.

Hey there Cindy
To get your issue more exposure I would suggest posting it in the commercial forums since this is a commercial product. You can do this at Commercial Forums.
I hope this helps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Problem installing windows via bootcamp. Driver issue on Mavericks

(Sorry just posted this elsewhere , then found the Bootcamp part of this forum, so i copied it here )
Ok, for the past few days i have done alot of attempts at finding an exact answer to my problem, but to no avail. So hopefully as i describe it here , it could help get me pointed in the right direction.
I have a late 2009 imac, with Mavericks installed. I have tried installing windows 7 both 32 & 64, i get the partition done in bootcamp, reboot process etc , gets to windows install screen, but now when it searches for its first drivers it cannot find it and i am forced to exit out and go back to osx etc, and start researching another way to solve the problem.
I have read there is a problem with downloading the apple support software thru bootcamp, so ive done it from the website directly. Am i correct with the following here ,-- These files put on the thumb drive, are NOT the drivers for windows, they are to be installed after windows is installed. Right ?
Recently i read windows 7 cant be put on mavericks, but that was a thread related to a different computer and year than mine. So that lead to even more confusion. So apologies, but i do hope i can get a simple way to get this completed. I appreciate your time & help in advance.

Ok thanks! just one more question now, should i go out and buy windows xp? i am a college kid who has an opportunity for a free upgrade to windows 7 professional. or should i just go out and buy windows 7 itself? Would downloading the upgrade be a smart option because i may be able to spend less money total? or should i not take a chance on that and just buy the home premium of windows 7?
thanks!

Windows 7: graphics/video driver issues

Hi,
i've just installed Windows 7 pro (oem version) on my macbook pro (unibody june 2009 edition, running Leopard OS) - installation was quick and painless. I made sure to install the boot camp drivers/leopard from the discs within Windows, however win 7 is still unable to detect my NVidia GeForce GT 9600 graphics card.
It's detected instead as a 'standard vga graphics adapter'. I then tried to install the latest driver from the NVidia website, however during the installation process it comes up with an error message stating it 'cannot locate any drivers that are compatible with current hardware' and exits.
Completely stumped. Could anyone help me out?

Problem solved, just a matter of getting my hands of Snow Leopard's Boot camp 3.0

Windows 7 display size driver issues

I recently installed windows 7 on my 15" retina MBP, and I don't think the graphics drivers have installed properly because the max screen resolution I can set in the control panel is 1600x1200. It looks ok but it's a bit pixelated and slightly stretched.
I think the reason for this is that I may have downloaded an outdated copy of the bootcamp support software, as I got it from a thread on this site as opposed to the download in bootcamp.
To fix this I went back into OSX and downloaded the latest drivers and tried to install them in windows, but all I could do was 'repair' when I ran the setup.exe, which still didn't work.
Am I right in assuming it was the old drivers causing the problem in the first place? And if so why can't I overwrite them with new ones?
Would it be easier to do the whole installation process again, as I don't have any files on the windows section?

look for uninstalling driver first, or the entire Boot Camp and anything Apple (and its folders) No need to nuke and start over
look for mobile graphics or the Intel Integrated 4000 if that is what it uses.
don't assume that Apples drivers are all and enough
but don't go using older drivers either.

Bug Report - Windows 8.0 - 6.0.1 USB arbitration causes USB keyboard driver failure

Can't find a place to submit a bug report. So here goes.
Full Error Message:
Windows cannot load the device driver for this hardware because a previous instance of the device driver is still in memory.
Problem Occurs:
Windows 8.0 x64
Vmware Player 6.0.1 build-1379776
Problem:
A USB keyboard ceases to function on the host operating system following the first host OS reboot after installing 6.0.1 on Windows 8.0. This issue does not occur with 6.0.0. The issue disappears upon uninstalling Player 6.0.1. Reinstallation allows Player to operate as expected, but issue re-appears after host OS reboot.
The issue happens immediately after host OS loads, and continues irrespective of whether VMWare Player is launched.
Looking at the keyboard drivers, the usb keyboard's driver has not loaded (see attached images). The built-in keyboard driver however reports no errors and continues to operate as usual.
Changing the USB keyboard device to that of a different manufacturer does not resolve the issue. Any USB keyboard driver appears to fail.
Work Around:
1) Launch msconfig
2) Disable VMWare USB arbitration service
3) Reboot
4) USB Keyboard works. VMWare Player continues to operate as normal, minus the ability to mount USB storage devices on the guest OS.

This issue was fixed on my PC as follows.
1) Taking ownership of the above usb*.sys files in the drivers folder
2) renaming them to usb*.sysold
3) Using Device Manager to uninstall all USB devices with the yellow warning ! next to them
4) Doing a Scan for Hardware changes via the Device Manager toolbar and then waiting a few moments whilst the USB devices are re-installed with signed drivers.
Hope this helps you....
usb drivers files in my drivers folder after the above process:
12/02/2013 04:12            19,968 usb8023.sys
21/11/2010 03:24            32,896 USBCAMD2.sys
27/11/2013 01:41            99,840 usbccgp.sys
12/07/2013 10:41           100,864 usbcir.sys
27/11/2013 01:41             7,808 usbd.sys
27/11/2013 01:41            53,248 usbehci.sys
25/03/2011 03:29            52,736 usbehci.sysold
27/11/2013 01:41           343,040 usbhub.sys
25/03/2011 03:29           343,040 usbhub.sysold
25/03/2011 03:29            25,600 usbohci.sys
27/11/2013 01:41           325,120 usbport.sys
25/03/2011 03:29           325,120 usbport.sysold
14/07/2009 00:38            25,088 usbprint.sysold
11/03/2011 04:37            91,648 USBSTOR.SYS
25/03/2011 03:29            30,720 usbuhci.sys
21/11/2010 03:23           184,960 usbvideo.sys
              19 File(s)      2,783,104 bytes
The .sysold files are the ones I renamed, I think also renamed the usbccgp.sys - but accidentally deleted it after the rename..

ThinkPad USB Keyboard with TrackPoint (55Y9053) driver issue (keys not working)

Hello!
I bought this external keyboard yesterday for my Dell desktop running windows 7 (professional) because I liked the thinkpad keyboard in my thinkpad t400. After plugging in to my desktop and installing the drivers that came in the CD, I noticed some keys (u, o, m, enter(return), l) were not working, i.e., nothing get displayed when I press those keys . When I tried installing it on thinkpad t400 running Windows 7 professional, the same non-working keys were displaying numbers instead of alphabet values.
Please note the keyboard is not 55Y9003 but the newer version 55Y9053. Also, note the trackpoint worked well including scrolling and all other keys were working. Interestingly, when I plugged this keyboard on Ubuntu machine (desktop and laptop), everything worked well without even installing any drivers.
I initially thought it was a hardware problem and got replacement from Amazon. Both the keyboards exhibit the same problem. Given the fact it works nicely on Ubuntu, I think this is a driver issue. I tried installing drivers from thinkpad site including versions 1.6 and 1.7.
I would appreciate if someone can help with the right drivers.
Thank you,
Vinai
Solved!
Go to Solution.

How does the keyboard compare to the one on the T400? I'm considering purchasing one for my desktop because I'm addicted to the TrackPoint.
When asking for help, post your question in the forum. Remember to include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help others with the same question in the future.
My TPs: Twist 2HU: i5-3317U Win 8 Pro, 4GB RAM 250GB Samsung 840 | T420 4177CTO: i5-2520M, HD+, Win 7 Pro x64, 8GB RAM, Optimus, 160GB Intel 320 SSD, Intel 6300 WiFi, BT 3.0 | T400 2764CTO: P8700, WXGA, Win 7 Ult x64, AMD 3470, 8GB RAM, 64GB Samsung SSD, BT, Intel 5300 WiFi | A20m 14.1" PIII 500 (retired). Monitors: 2x Dell U2211h IPS 100% sRGB calibrated w/ Spyder3.

Windows 8 64-bit install on 970a-g46 Mainboard AHCI and NVIDIA DRIVER issues

My Box:
MSI 970A-G46
BIOS 1.9 (AUG 2012) (Tried 1.11 but the nightmare started then)
AMD FX-6100 (STOCK SPEED AND SETTINGS) WITH OEM HSF
16GB PATRIOT VIPER 3 (1866) RUNNING @ (1600)
USED an EVGA 9800GT 1ST AND UPGRADED TO NVIDIA REFERENCE CARD GTX 550 Ti (1GB) WITH SAME ISSUES
90gb MonsterDigital Daytona SATA III SSD DRIVE (OS and minimal programs)
Antec HE 550
I am at a point of pulling my hair out. I decided to upgrade my system to enhance Diablo III game play. I got a combo deal on the mainboard and cpu, and thought the speed of the game caching on a SSD would also help. The first attempt which took a little struggle was Vista 64-bit. Eventually, I was able to get the OS to work with me, and it was smooth. Since M$ decided to offer the Windows 8 Pro upgrade for only $39.99, I thought, what do I had to lose. Well….lots of time. Now, I am not a newbie, though SSD drives haven’t been more than an interesting thought. So yes, I read many guides on everything from Trim enabled Win 7 and 8, and many other do’s and don’ts. What is driving me to the Netherlands of hell, is the installation and how buggy it has been. It boils down to drivers for the IDE/SATA/AHCI CONTROLLER. First, even thought it “sees” the SSD on installation drive selection, after pulling the USB installation drive, the system forgets it, and there is a “problem with the boot sector”. If you load the driver from the AMD site, it lets the install occur “fine”, but there is an issue with that driver which causes an irq conflict which leads to D3 audio issues and freeze ups. I did finally get things in order (not sure which driver I choose for that), and things were smooth, except I tried to install the GTX 550 ti and that led to a corrupt file error, which the system runs a check disk and cycles the “preparing to repair” and “diagnosing PC” a few times and never allows me to enter SAFE MODE (shift+f8), to disable the NVIDIA driver that is buggy, and doesn’t allow for the NVIDIA Control Panel to install without losing video, and starts the repair cycles again… Leading to ANOTHER RE-INSTALL...
My question, for the Windows 8 Pro installation on the 970a-G46 mainboard and then after install is complete, which driver is the correct choice for the AHCI/SATA Controller? All I find is Win7 64-bit AHCI inf’s, and SB7XX 64-bit inf’s (no SB950 INF). The Driver disk which came with the mainboard is very dated pre Win 8 stuff, ASMEDIA X106 which are not recognized by the OS as written for Win 8. AMD’s latest drivers are the ones causing the IRQ type lags and corruption.
What version, build and type of Windows 8 installations have you used on this mainboard, and what drivers allowed you install it without the above conflicts? Your input may decrease my insanity… So, thank you in advance…

Quote from: m0r9h3u5 on 28-January-13, 12:11:16
I understand what you are telling me, only the generic drivers deliver subpar results. What is the point of running those drivers instead of windows 8 certified drivers written for said devices. My last install is functioning better, but still windows update fails every attempt, the apps i install (ie. weather bug) on the start screen wont load... to me windows 8 is a big fail....but that is just my view...
OK...I also own the 970a G46, and my upgrade experience from Win7 x64 AHCI to Win8 x64 AHCI was flawless the first time. No problems at all. You are running an AMD chipset board with a nVidia gpu, which means that your chipset drivers are not automatically updated with every gpu driver update you do--this would happen automatically if you owned an AMD gpu because AMD includes them in its gpu driver install packages. But--all you have to do to get the proper drivers for your motherboard is go here and download them. You only need the *chipset drivers* from this page--you do not need the RAID drivers, of course. That's it. It's no big deal, and back in the days when nVidia was making motherboard chipsets you had to separately download both the motherboard chipset drivers from nVidia and the AMD gpu drivers from AMD if you did not also own a nVidia gpu.
From your description of your problems it sounds like your installation of Win8 is hosed and you need to format C:\ and clean install from scratch, anyway, so...
A note about AHCI--the *ideal* way to install the AHCI drivers is prior to installing your OS for the first time, you enter the UEFI and set "AHCI" in the appropriate place, instead of IDE, and *then* you reboot from DVD and install your OS which will automatically install the correct AHCI driver from Windows. After the driver installation is complete you should then install the updated 970a drivers from AMD as linked above.
However, it is actually very easy to activate and install AHCI *after* you have installed Windows in normal IDE mode:
To enable AHCI in existing Windows 8 IDE Installation's
Caution: Do NOT enable AHCI in UEFI prior to making the following changes in your Registry! If you had AHCI enabled alreadyin UEFI, disable it first and restart your computer!
Use WinKey + R and type Regedit in the command line and hit the Enter key, this will open the Registration Editor.
Go to:
HKEY_LOCAL_MACHINE/SYSTEM/CurrentControlSet/services/iaStorV
right click on Start, select Modify and set Data Value to 0
Close Registration Editor and restart computer.
While booting, open the UEFI Page and set the SATA Mode to AHCI from IDE
Save UEFI settings and restart.
Windows will now install the AHCI drivers automatically and they should work without issues.
In order to avoid installation problems just like you have been experiencing, here is what I would do in your shoes:
1) Set UEFI for normal IDE drive mode
2) Reboot into IDE mode and install your OS
3) After you have finished with the installation, you should be having no troubles in IDE mode. Then go to the instructions above on how to properly enable AHCI *after* you have installed Windows 8 in normal IDE mode.
4) After everything is coming up roses in AHCI mode and you are having no problems, then install the AMD chipset drivers as linked above and you are golden.
Those 4 steps worked perfectly for me the first time (the first time I got them right, that is...).
There's nothing wrong with Win8--this is strictly operator error caused by insufficient research into what AHCI is and how to properly enable it. The Internet has some bad info on Win8 registry settings for AHCI because of the developer preview and the consumer preview versions of Win8 that Microsoft released to the public prior to the final shipping build--many "instructions" for Win8 are therefore not valid for the shipping version of Win8. At first I made some of the same goofs that you did, but now you get to benefit from my hard-won experience... Good luck! Should work like a charm. And, registry AHCI is done differently in Win8 than it is done in Win7 or Vista. Also, the registry settings relative to AHCI in Windows 8 for AMD are different from the registry values that must be changed for an Intel controller.
Parenthetically, My FX-6300 (Vishera) will be here in a couple of days! Yeah!

Pixma ip6000d windows 7 driver issue. How do you get one?

Has anyone solved the windows 7 driver issue? The canon website does not have one yet is reported windows 7 capatable.

Hello ricksterofmi,
The PIXMA iP6000D Drivers are included with the Windows 7 Operating System through Windows Update. Please connect the PIXMA iP6000D to your computer and automatically install the drivers. Once this has been done, visit our website by selecting this LINK to download and install the Add On Module for full compatibility.
I hope this helps.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

HP 6600 Scan\Print Driver Issue for Windows 7 Professional 64 bit

Hello,
For some time now I have been unable to scan or print from my desktop (Windows 7 Professional 64bit) and I have exhausted too much effort and am now bringing it to the masses.
The problem:
Printing: Currently receiving an "Error - Offline" message in my printer queue at all times.
Scanning: Scanning has never fully worked on this desktop. I am always unable to communicate with the printer. (Though webscan works through accessing the printers IP address)
Things I have tried:
Ran HPPSDr, followed directions (Unpluged power to printer, turn back on, restart computer) brings me to this website after it cannot fix. (Note that while the HPPSDr is running it always notions that there is a driver problem)
Uninstalled Drivers from CD-ROM, re-installed, countless times
Installed "Windows 7 Pro 64 bit drivers" from the HP website and uninstalled, countless times.
Attempted to set a static IP and use "Update IP Address" to point specifically at the printers IP.
Installed Drivers and finding the printer myself through it's own static IP address.
Turned off firewall and attempted to print (after reboot), same errors
Setting up the printer on all of my laptops (3) wirelessly to attempt to find if there is a problem with the printer or static IP. (1 is Windows VISTA 32bit and the other 2 are Ubuntu 32bit). All laptops are able to use the printer wirelessly without any problems.
Read all of the forums about this issue and attempted all of the 'solutions'. Although I mostly don't see that anyone with this same problem is resolved, unless I'm missing the perfect post.
Things I have not tried:
Plugging the USB directly into the desktop. (This seems self defeating as the purpose for this printer was to be able to print wirelessly to it from across the room)
Re-installed Windows 7 Pro 64bit (Trying to avoid this, would rather just print from laptops)
You tell me
Curiosities:
I have noticed strange things that make me believe the driver is somehow incomptable with my OS. Here is a shot of the properties of the printer:
Weird that it is not recognizing the model number.
Also in the Printer Settings when I go to the port tab, there is no port selected, if I try and tab away it forces me to select a port, yet when I do and 'apply' and then re-open the Printer Settings in the ports tab; it has again unselected the previously selected port.
Theories:
I feel like my OS is just refusing to notice the IP address for the wireless printer, no matter what I have it set to, even if it's dynamic. It's like the driver for Windows 7 Pro 64bit is actually not the correct driver for my system.
Anyways, another thing to mention is that I am not currently willing to wipe my operating system and re-install Windows 7 Pro in order to resolve this just yet. I want to see if anyone else has any other avenues I can try before even beginning to consider that.
Anyways, thanks in advance for taking the time to read my ramblings and hopefully someone who has resolved this issue can help me.

Hi Zerosouls,
I understand you are having an issue with HP 6600 Scan\Print Driver Issue for Windows 7 Professional 64 bit.
First try to click the Windows icon, type services in the Search box, and then click or tap View Local Services. Scroll down to the Windows Installer. Startup type should be - Automatic, and Service Status should be - started
Restart the computer after this step and try installing Hp Officejet 6600 again.
Please let me know what happens
Thanks
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

HP PSC 1510 driver issue with Windows 8.1

I can't get my HP PSC 1510 all in one to work with Window's 8.1. I've installed HP doctor and the driver fails. I've downloaded the new driver so I don't know what the issue is? Anybody solve a similar issue?

Hi @DerekRL , and welcome to the HP Forums!
I can see you're experiencing driver issues. I'd like to help!
I would suggest Uninstalling the Printer Software.
Once it is uninstalled, I would suggest putting your system into clean boot mode within the Microsoft configuration. You can do so by following this document: How to perform a clean boot in Windows.
Once the computer is in clean boot mode, I would suggest reinstalling the HP Printer Install Wizard for Windows.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

X201 Windows 8.1 Keyboard driver issue

Similar Messages

Maybe you are looking for