X201 Wireless switch Hardware problem - PLEASE HELP

Hello everyone,
I have been a regular reader of this wonderful forum and have also participated on a few questions. I have an x201 which I bought from UK 6months back.
After a smooth sail for many months and just when I thought life was going good, I have a wireless switch problem that pops up out of nowhere. I never use hardware switch and had to do it only last week because of checking for my internet connection problems.
Only once in my entire experience with this laptop that I put it off, now it has become so sensitive that even shaking the laptop while typing turns off the laptop. On reading about this problem I found out that it is quite a common problem with x-series and has many users affected from it. After confidently calling the customer support they ask me to pay 200euros just to "TAKE A LOOK AT THE PROBLEM"????. Apart from at least acknowledging the persistent problem across all the models they end up asking me to pay for everything and cannot tell me how much it will cost me or even tell me how long it will take to replace this.
Is there any other way to do this? The support told me that the only other way to repair this will be to buy the Base switch myself and then replace it. I am a biologist doing my PhD and have no knowledge of all these. Apart from all the appluad this laptop got from my colleagues, now they all think this is a joke by Lenovo to be charging for something that is entirely their mistake.
Can anyone point to a solution please and help me. I was really looking to buying an ultrabook next year but looks like replacing a switch is going to cost me 1/4th of what one would be for an entire laptop.
PLEASE HELP

Hi chaihg,
I understand that the issue has not been resolved.
I would like to see if I can help and I've PMed you for some details. Do let me know.
thanks!
lak_sg
WW Social Media
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

Software or hardware problem, please help

I have my MacBookPro(early 2008) 2,6 Ghz Intel duo. 4 Gb 15 inch, with all the updated software....It was getting slow, so I used the disk utility to check the and try to to solve problems I found this
el archivo SUID “System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAg ent” se ha modificado y no se reparará. (the archive has been modified and will not repaired.)
I also run ONYX and have the same answer.
After that finding the mac doesn´t start, no signals on the screen, the disk makes noise but nothing happens.....I find out that MBP, has a video card that after a few years stops working, because I found that message I am doubting of a Hardware (videocard) or a system problem , any help ?
I just bought an imac to transfer all my work as I used that computer as a desktop.....but I wanted to recover the data and make it work to take it to work.....
Any help will be great !
I have an important presentation next january and I need to recover the data....
Message was edited by: Oriol LLena

Connect the Time Machine backup drive to the iMac. If you've never started up the new iMac, then when you do you will enter the Setup Assistant where you can opt to restore from a Time Machine backup. Just follow directions.
If the iMac has already been through the Setup Assistant, then open Migration Assistant in the Utilities folder and use it to migrate from the Time Machine backup drive.
A Basic Guide for Migrating to Intel-Macs
The Knowledgebase article Intel-based Mac: Some migrated applications may need to be updated refers to methods of dealing with migrating from PowerPC chips to Intel with the Migration Assistant safely. The authors of this tip have not had a chance to verify this works in all instances, or that it avoids the 10.6.1 and earlier Guest Account bug that caused account information to get deleted upon use of the Migration/Setup Assistant. However, a well backed up source that includes at least two backups of all the data that are not connected to your machine will help you avoid potential issues, should they arise. In event it does not work, follow the steps below.
If you are migrating a PowerPC system (G3, G4, or G5) to an Intel-Mac be careful what you migrate. Keep in mind that some items that may get transferred will not work on Intel machines and may end up causing your computer's operating system to malfunction.
Rosetta supports "software that runs on the PowerPC G3, G4, or G5 processor that are built for Mac OS X". This excludes the items that are not universal binaries or simply will not work in Rosetta:
1. Classic Environment, and subsequently any Mac OS 9 or earlier applications
2. Screensavers written for the PowerPC System Preference add-ons
3. All Unsanity Haxies Browser and other plug-ins
4. Contextual Menu Items
5. Applications which specifically require the PowerPC G5 Kernel extensions
6. Java applications with JNI (PowerPC) libraries
See also What Can Be Translated by Rosetta.
In addition to the above you could also have problems with migrated cache files and/or cache files containing code that is incompatible.
If you migrate a user folder that contains any of these items, you may find that your Intel-Mac is malfunctioning. It would be wise to take care when migrating your systems from a PowerPC platform to an Intel-Mac platform to assure that you do not migrate these incompatible items.
If you have problems with applications not working, then completely uninstall said application and reinstall it from scratch. Take great care with Java applications and Java-based Peer-to-Peer applications. Many Java apps will not work on Intel-Macs as they are currently compiled. As of this time Limewire, Cabos, and Acquisition are available as universal binaries. Do not install browser plug-ins such as Flash or Shockwave from downloaded installers unless they are universal binaries. The version of OS X installed on your Intel-Mac comes with special compatible versions of Flash and Shockwave plug-ins for use with your browser.
The same problem will exist for any hardware drivers such as mouse software unless the drivers have been compiled as universal binaries. For third-party mice the current choices are USB Overdrive or SteerMouse. Contact the developer or manufacturer of your third-party mouse software to find out when a universal binary version will be available.
Also be careful with some backup utilities and third-party disk repair utilities. Disk Warrior, TechTool Pro , SuperDuper , and Drive Genius work properly on Intel-Macs with Leopard. The same caution may apply to the many "maintenance" utilities that have not yet been converted to universal binaries. Leopard Cache Cleaner, Onyx, TinkerTool System, and Cocktail are now compatible with Leopard.
Before migrating or installing software on your Intel-Mac check MacFixit's Rosetta Compatibility Index.
Additional links that will be helpful to new Intel-Mac users:
1. Intel In Macs
2. Apple Guide to Universal Applications
3. MacInTouch List of Compatible Universal Binaries
4. MacInTouch List of Rosetta Compatible Applications
5. MacUpdate List of Intel-Compatible Software
6. Transferring data with Setup Assistant - Migration Assistant FAQ
7. OS X Lion: How to use Migration Assistant to transfer files from another Mac
Because Migration Assistant isn't the ideal way to migrate from PowerPC to Intel Macs, using Target Disk Mode, copying the critical contents to CD and DVD, an external hard drive, or networking will work better when moving from PowerPC to Intel Macs. The initial section below discusses Target Disk Mode. It is then followed by a section which discusses networking with Macs that lack Firewire.
If both computers support the use of Firewire then you can use the following instructions:
1. Repair the hard drive and permissions using Disk Utility.
2. Backup your data. This is vitally important in case you make a mistake
      or there's some other problem.
3. Connect a Firewire cable between your old Mac and your new Intel Mac.
4. Startup your old Mac in Transferring files between two computers using FireWire.
5. Startup your new Mac for the first time, go through the setup and
       registration screens, but do NOT migrate data over. Get to your
       desktop on the new Mac without migrating any new data over.
If you are not able to use a Firewire connection (for example you have a Late 2008 MacBook that only supports USB:)
1. Set up a local home network: Creating a small Ethernet Network.
2. If you have a MacBook Air or Late 2008 MacBook see the following:
a. MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch,
      http://support.apple.com/kb/HT3224;
      Late 2008) - What to do if migration is unsuccessful;
b. MacBook Air - Migration Tips and Tricks;
c. MacBook Air - Remote Disc, Migration, or Remote Install Mac OS X and
      http://support.apple.com/kb/HT3224; wireless 802.11n networks.
Copy the following items from your old Mac to the new Mac:
In your /Home/ folder: Documents, Movies, Music, Pictures, and Sites folders.
In your /Home/Library/ folder:
/Home/Library/Application Support/AddressBook (copy the whole folder) /Home/Library/Application Support/iCal (copy the whole folder)
Also in /Home/Library/Application Support (copy whatever else you need including folders for any third-party applications)
/Home/Library/Keychains (copy the whole folder) /Home/Library/Mail (copy the whole folder) /Home/Library/Preferences/ (copy the whole folder) /Home /Library/Calendars (copy the whole folder) /Home /Library/iTunes (copy the whole folder) /Home /Library/Safari (copy the whole folder)
If you want cookies:
/Home/Library/Cookies/Cookies.plist /Home/Library/Application Support/WebFoundation/HTTPCookies.plist
For Entourage users:
Entourage is in /Home/Documents/Microsoft User Data Also in /Home/Library/Preferences/Microsoft.
Credit goes to Macjack for this information.
If you need to transfer data for other applications please ask the vendor or ask in the Discussions where specific applications store their data.
5. Once you have transferred what you need restart the new Mac and test to make sure the contents are there for each of the applications.
Written by Kappy with additional contributions from a brody.Revised 5/21/2011

Powermac g5, Hardware Problem PLEASE HELP - I MIGHT GET FIRED

My work computer, G5 powermac, case was damaged. Ordered a new one, transfered all components, but now it won't start up. I am so screwed. When I plug it in, I hear a click. Nothing happens when I hit the power button. Any ideas. Please help. I might get fired over this. Are there any specific hardware related reasons my mac wouldn't start up? Please help.
Adrian

If the power supply was out the computer would be
just dead. Nothing. no noise nothing. I agree that
you should double check your connections. Is the
clicking noise comming from the power supply. The
only thing that could click in my mind is the HDD
when the pin is striking the side of the HDD
well it seems dead. but when you either unplug it or plug it in i hear a click that is definantly coming from the power supply. I have rechecked all connections.

Toshiba P305 major hardware problems PLease help

I have a satellite p305. The headphone jack stopped working and the touchpad and click buttons stopped working. I tried updating drivers but nothing changed. The other problem was whenever you had to programs open that produce sound (windows media player and a you tube video or similar) The audio came out staticky. This is not when trying to listen to both players at the same time, one is paused. But if you have both of them open one will be staticky. I tore the computer down to see if there was anything visually wrong with it at the headphone jack or where the click butons and touch pad plug in but found nothing. I put the motherboard back in and put it all back together and plugged it in and pressed the power button. The buttons light up and i think either the hard drive or fan spun but nothing else happened after that. Im thinking bad MOBO but i need some advise because this is a computer that i am working on for someone else and really dont want the whole you broke my computer game to be played.

This is one problem within the DirectX 9.0b:
Please take a good look at this update for Microsoft DirectX v9.0b:
http://www.microsoft.com/downloads/details.aspx?FamilyID=8dfd1b6d-e177-4a0e-91d0-b4310675b02b&DisplayLang=en
Possible Issue Description:
- TV-Tuner card cannot keep TV-Tuner settings in memory;
- TV-Tuner card cannot be initialized in system after installing DirectX v9.0b;
- TV-Tuner card cannot capture any picture;
Official Microsoft Information:
DirectX 9.0b was released on 7/23/03 to address the MIDI security issue identified in bulletin MS03-030. A small number of non-security fixes were also included in the release. One of these fixes caused several TV Tuner capture card/driver combinations using video formats other than NTSC (NTSC-J, PAL, SECAM) to no longer initialize correctly on Windows 2000, Windows XP, and Windows Server 2003. Symptoms include loss of capture functionality and potential inability to set/retain device capture settings. This hotfix, documented further in Knowledge Base article 825116, has been issued to correct the flaw.
I believe that your SB card is sharing IRQs with your Firewire hardwares thus causing errors.

Hp 87130 switch driver problem PLEASE HELP

i was writing the sending a typical instruction route:driven:all;
straight into a the switch driver and it gives me an error "undefined header."
i know i have the right gpib address because i was able to turn off the led by
using the *cls and *rst commands. but i took that instruction straight off of
the manual for the 87130 and it still doesn't work.
Posted from [207.110.6.67]
via Mailgate.ORG Server - http://www.Mailgate.ORG

Hello-
It sounds like the interface is working, but the instrument is not responding. It may help to contact Agilent about this instrument. My initial guess is that there could be a couple of causes:
-The instrument needs to be configured to receive GPIB commands.
-The semi-colon is not a valid end-of-string (EOS) character.
Randy Solomonson
Application Engineer
National Instruments

My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

My Ipad 2 does not turn on when not plugged to electricity. Even when plugged to electricity, it constantly restarts/switches itself off. what is the problem, please help??

i plugged it and pressed the home button for a few seconds. the connect to itunes screen appeared and the moment i disconnect the cable from the electric plug, it switches off. when i connect the cable to the PC, nothing happens, its as if nothing has been done.

My iphone 5 32 gb has an camera autofocus problem, please help me solve this

my iphone 5 32 gb has an camera autofocus problem, please help me solve this

Hi teejayfs,
Thanks for visiting Apple Support Communities.
If you've noticed unexpected behavior with your iPhone camera, start with these steps to isolate or resolve the issue:
Camera isn't functioning or has undesired image quality
If the screen shows a closed lens or black image, force quit the Camera app.
If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
Try turning iPhone off and then back on.
Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
Try to remain steady while focusing:
Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
Note: Video-recording features are not available on original iPhone or iPhone 3G.
If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
You can find these steps here:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Regards,
Jeremy

My macbook pro 15inch running on maverick when i try to click on wi-fi says no hardware installed please help i need wifi and and under network staus wi-fi is fail and under network airport is not connected can anybody help the wifi icon has a x and does

my macbook pro 15inch running on maverick when i try to click on wi-fi says no hardware installed please help i need wifi and and under network staus wi-fi is fail and under network airport is not connected can anybody help the wifi icon has a x and does not even let me turn it on

Have you attempted to reset the SMC? That would be the first step. Hold the left control, option, shift key and the power button for about 5 seconds and release. Then try to reboot. Might as well reset the PRAM as well. Hold command, option, P, R on start up until the machine restarts. If that doesnt' have any affect we'll have to dig deeper into a potential hardware failure.
If this method doesn't work, check the webcam that will tell the problem is on the iSight & WiFi cable. If your webcam is ok, then it'll be the WiFi card problem. Hope it can help ;-)
- xia_us9

X-Fi Fatal1ty Plat1num Champion Ed. problem, please help!

9X-Fi Fatalty Platnum Champion Ed. problem, please help!? Hi there everyone,
So i have a X-Fi Fatalty Platnum Champion Ed. and a computer with Windows 7.
I've searched the web and i found many people saying that the card it's working and perfectly compatible so i would like to exclude this option as far as the problems that i'm having.
So, right out of the box i've placed the front panel in with the ribbon cable and the power connected to it, then i connected the other end of the ribbon cable and finally placed the card in one of the PCI slots i have free.
Now, when i start my PC, i don't hear any particolar "beep messages" but nothing will come on the screen, in few words my PC will not boot at all. I can hear the HDD spinning, everything sounds normal except for that "little" problem.
So, i re-did all the connections thinking that maybe i did something wrong, but following the instruction i did exactly as told. So i tried again to power up the computer and i've noticed that the X-Fi logo is lit up (red light) and.. I don't really know if that means something or it's just something aside that doesn't really matter.. But, what is it's The PCI card is broken or there's something else?
I did try to disable the sound card (integrated mobo sound) from the BIOS but that didn't change anything. I did try all the software options but this looks like more of an hardware problem (please correct me if i'm wrong and/or i've missed something).
There's something that popped up in my mind.. the PSU. I noticed that i have a 300W PSU (mm.. low, isn't it's)?and i was wondering if that's enough or i need a more powerful one.. and if that's may be the case for the PCI to not work at all causing all i've already explained above. I mean.. It seems like i've installed a dead peripheral and that's impeding the computer to start up..
I don't know.. I need clarification and help, PLEASE.
Thank you very much in advance!

Look at the beta thread sticked above but good luck waiting for a new driver. That beta driver has been there since January and although better than the normal driver it is still crap.
All the boot type issues are with the SSD but if you getting in game crashes etc... under windows 8 that is simply that the driver stinks.

Hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

hello sir my iphone screen turns off after using 2-5 minutes what would be the problem please help me out

To make sure that this is not software related, set it back to factory settings, without using any backup data afterwards. Set up the rest of the personal settings manually and test the phone. If it still does not work, this is a hardware issue and the phone has to be serviced by Apple or an Authorized Apple Service Provider:
Use iTunes to restore your iOS device to factory settings - Apple Support
Find an Apple Authorized Service Provider
iPhone - Contact Support - Apple Support

Hi .. my iPad 4 with iso 7.0.3 he is restarting himself ... How can i solve this problem please help me

Hi .. my iPad 4 with iso 7.0.3 he is restarting himself ... How can i solve this problem please help me

Standard troubleshooting...
1. Try a Restart by pressing the sleep/lock button until you see the slider. Slide to power off. Restart by pressing the sleep/lock button until you see the Apple logo.
2. Try a Reset by pressing the home and sleep buttons until you see the Apple logo. Takes about 5-15 secs of button holding and you won't lose any data or settings.
3. Remove apps from Recently Used list...
- From any Home Screen, double tap the home button to bring up the Recents List
- Swipe up on the app preview card to remove it from the list
- Press the home button when done.
4. If still a problem restore with your backup.
5. If still a problem restore as new, i.e. without your backup. See how it runs with nothing synced to it.
6. If still a problem, it's likely a hardware issue.

P6N Lots of problems please help

P6N Lots of problems please help
The setup is the following:
P4 D935 3.2gHz
P6N Diamond MS-7320 Bios 1.3V
Corsair XMS2-6400C4DHX
NX8600GT-TD512EZ/D2
Seagate Barracuda 7200 250Gb SataII 16Mb
Akasa 460W Dual Rail
Please help I have lots and lots of problems with lockups that can happen any time post , bios , loading vista and sometimes during OS. Some times will work ok play games etc. Already tried different combinations fitting the mem modules even tried and some pc4200 modules same problems. Spent lots of hours clocking the mems with different settings but non is stable. I am not interested in overcloking just to make it stable to start with. When is actually running is fine is more than enough for me. Already looked to lots of posts on the msi forum but… Since the cpu is old can I go back on an older bios version???? The Corsair modules have to run at 2.1V or is it possible to use them with slower setting. So confused so lost ….. please HELLPPPPP
Any help greatly appreciated.

please, don't buy any more unneded parts. first find the problem then buy if no solutions available.
One thing I find with BIOS issues is to do a full clear.
1. disconnect the power cord from the power supply(turn switch to off if there is one.
2. hit the power switch to clear the power out of the system.
3. set the cmos jumper to clear and leave there if one is available.
4. Pull the battery.
5. carefully short out the battery connector on the motherboard to drain any power left.
6. press the clear cmos button and hold for 30sec minimum, if you didn't have a jumper to set.
7. replace battery, move jumper back, plug in power cord, turn on power sipply switch.
Now it should hopefully power up. go into BIOS and load optimized results. hit save and exit and when it gets back to the post screen, go back into bios and set your normal MB settings(ie. set boot devices, boot order, disable sound if using sound card, etc...)
go into your H/W Monitor section and list the CPU Vcore settings to make sure it is getting the power it needs. I just looked it up and it's suppose to run from 1.225v - 1.325v.
also, try your most generic ram you have with auto settings. the faster the ram usually the more volts they need and default volts are 1.8v for ram and sometimes faster chips have issues with lower volts.
Let me know how this works for you.
-=Mark=-
ps. make sure everything is unplugged from the computer you don't need. just cpu, 1 stick of ram, and video. and of course keyboad and mouse. Please make a signature with all your systems specs including make and model numbers. I hate guessing at solutions and I'd hate to see you buy any more unneccessary parts because of lack of information.

990fxa gd80 raid 0 problem please help me i am begging you

so i will start with my set up
990fxa dg80 mb
fx 8350 cpu
780ti
8 gig of ram
256 hdd
2x samsung 850 evo
750 hybrid drive
So at this stage all my data is on the 750 hdd and the disk is stored away. my problem started with me buyng 2 mx100 256 ssds . If my bios is set to ide or ahci they work fine i had my windows instaled on 1 of them all woks fine. Once i switch my bios to raid ( before i set up my raid 0) boot up win 7 instalation i do not see any drives ( i know is normal) load the drivers for the raid controler (sb950 for w7 as it says in themanual) and only my 256 hdd shows up but not the ssds . Than i set them up in ld raid 0 same problem . Tryed on another 2 mbs ... 1 same and a gygabite same problem. So i was sure there is a problem with ssds. I got rid of them got 2 new 850 evo 250 gb same problem. please help me i am so desparate i am willing to pay woth body organs for help

I..have a few questions...
1. You set BIOS to the RAID mode, and under that option there's a Board SATA RAID ROM, do you set it as Legacy ROM?
2. Did you enter Ctrl+F to initialize the drives/Delete Array(If they're used SSDs) and create RAID0?
3. Is your Win7 64 bit or 32 bit?
4. I assume it's 64 bit, did you copy the W764 folder for driver loading?
And make sure you get the driver from here:
http://www.msi.com/support/mb/990FXAGD80.html#down-driver&Win7 64

My iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: "unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

my iphone is on recovery mode and i can´t turn on it, when i try to recover it from itunes i get: unknown error (36), i´ve tried to do lot of things but i can´t solve my problem. please help!!

Hi, i had the same problem. Try to find the file "apple" or "itunes" don't know it anymore exactly. Ahm well you need to delet any information or just plug in your iphone into an other computer. important is that your iphone never has been pluged in this computer before. This was what i did, and it worked!

Problem Please help me.....Let me know the area to look for it I am a DBA..

Problem Please help me.....Let me know the area to look for it I am a DBA..Thanks in advance to let me know the cause and the area to look and fix it...
Server Error in '/' Application.
Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.
Exception Details: System.Web.Services.Protocols.SoapException: Problem with SAP/BAPI. SAP.Connector.RfcCommunicationException: Connect to message server failed Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD LOCATION CPIC (TCP/IP) on local host ERROR service 'sapmsPRD' unknown TIME Wed May 04 08:59:06 2005 RELEASE 620 COMPONENT NI (network interface) VERSION 36 RC -3 MODULE ninti.c LINE 428 DETAIL NiPServToNo SYSTEM CALL getservbyname COUNTER 1 at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode) at SAP.Connector.SAPConnection.Open() at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn) at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn) at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type) at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)
Source Error:
An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.
Stack Trace:
[SoapException: Problem with SAP/BAPI.
SAP.Connector.RfcCommunicationException: Connect to message server failed
Connect_PM MSHOST=prddb01.lamrc.com, R3NAME=PRD, GROUP=Prod HR PRD
LOCATION    CPIC (TCP/IP) on local host
ERROR       service 'sapmsPRD' unknown
TIME        Wed May 04 08:59:06 2005
RELEASE     620
COMPONENT   NI (network interface)
VERSION     36
RC          -3
MODULE      ninti.c
LINE        428
DETAIL      NiPServToNo
SYSTEM CALL getservbyname
COUNTER     1
   at SAP.Connector.SAPConnection.ThrowRfcException(RFC_ERROR_INFO_EX rfcerrInfo, Encoding encoding, String languangeCode)
   at SAP.Connector.SAPConnection.Open()
   at SAP.Connector.SAPClient.RfcInvoke(String method, Object[] methodParamsIn)
   at SAP.Connector.SAPClient.SAPInvoke(String method, Object[] methodParamsIn)
   at SoftwareKeySAPG.SAPProxy1.Z_Bapi_Load_Kpi_Region(ZSOFT_KPI_REGIONS_MTable& Kpi_Regions, ZSOFT_PROD_TYPETable& Prod_Type)
   at SoftwareKeySAPG.SAPGSK.LoadKPIRegion(DataSet dsProduct)]
   System.Web.Services.Protocols.SoapHttpClientProtocol.ReadResponse(SoapClientMessage message, WebResponse response, Stream responseStream, Boolean asyncCall) +1503
   System.Web.Services.Protocols.SoapHttpClientProtocol.Invoke(String methodName, Object[] parameters) +218
   SoftwareKeyUI.InstalledBaseDataWS.InstalledBaseData.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBaseDataAccess.LoadKPIRegionMulti(DataSet products)
   SoftwareKeyUI.InstalledBase.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.FilteredAccess.GetRegionDetails(Int32 userId, String product, String regionType)
   SoftwareKeyUI.search.LoadRegionDetails()
   SoftwareKeyUI.search.regionType_SelectedIndexChanged(Object sender, EventArgs e)
   System.Web.UI.WebControls.ListControl.OnSelectedIndexChanged(EventArgs e) +108
   System.Web.UI.WebControls.DropDownList.System.Web.UI.IPostBackDataHandler.RaisePostDataChangedEvent() +26
   System.Web.UI.Page.RaiseChangedEvents() +115
   System.Web.UI.Page.ProcessRequestMain() +1099

The error is a very basic one - the sapmsPRD service is not known. You will have to go to <NT_ROOT>\system32\drivers\etc and add the entry sapmsPRD 3600 to this file.
This is basically telling the requester at what port to look for the message server.
C

X201 Wireless switch Hardware problem - PLEASE HELP

Similar Messages

Maybe you are looking for