X301 and Vodafone and AT&T Wireless WAN (HSPA) Driver for Windows 7 (32-bit, 64-bit)

Ok, I (Lenovo) did it again.
System Update showed me this update: "Vodafone and AT&T Wireless WAN (HSPA) Driver for Windows 7 (32-bit, 64-bit)".
As I'm using Vodafone and I had a AT&T driver, I decided to update.
The result is, that now the GPS doesn't work.
Yes, I'm in a place where the GPS signal is present (my house, with the previous driver I was able to get 6/7 satellites).
What happens? Lenovo TV GPS stays there trying to fix the satellites, but nothing happens. I can't recover the system to a previous state, as I updated Flash player too, and Windows only show me the possibility to roll back this update.
So, apart advicing everyone not to update, I kindky ask:
- where can I found the previous driver? I searched the web without success...
- why does Lenovo deploy driver which can cause problems (I just had one updating the BT driver last week! .msi installer problem, error 1935...)?
Thanks to everyone
600, R52, T61p, X301

Ok, I found in the Net the drive 7uw706ww.zip, which is Version 6.1.4.2, while the updated version is 6.1.10.5 (7UW708WW).
I tried again the GPS, and it wasn't working.
Anyway, before downgrading, I tried to reinstall the new driver, downloading and installing the .exe instead going through System Update.
Result: now GPS is working (same place, same conditions, just 5 minutes later)!
Don't know where the difference is...
600, R52, T61p, X301

Similar Messages

My external hard drive is 'seen' by my iMac and I can go into the Finder and open files and folders. I am using the hard drive for Time Machine back up. However Time Machine says it can't find the drive. Same thing has happened with Final Cut Express.

My new LaCie external hard drive is 'seen' by my iMac and I can go into the Finder and open files and folders. I am using the hard drive for Time Machine back up. However Time Machine says it can't find the drive.
The same thing happened recently between Final Cut Express and my other LaCie external hard drive used as the Scratch disk. It fixed itself.
I've run out of ideas. Help would be very much appreciated. Thanks.

have you done some searches on FCPx and time machine? Is there a known issue with using a TM drive with FCPx? dunno but ...wait...I'll take 60 sec for you cause I'm just that kind of guy.... google...." fcpx time machine problem" Frist page link
http://www.premiumbeat.com/blog/fcpx-bug-best-practices-for-using-external-hard- drives-and-final-cut-pro-x/
You cannot have time machine backups on your hard drive if you intend to use it in FCPX.
booya!

My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

My MacBook Pro stated that it needed to be updated. I clicked yes to restart the computer and update but when it restarted it stays on the gray screen with the apple logo and then pops up, stating "unable to find driver for this platform." What do I do?

Boot into Recovery by holding down the key combination command-R at the startup chime. Release the keys when you see a gray screen with a spinning dial.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with networks that require any kind of authentication other than a WPA or WPA2 Personal password.
When the Mac OS X Utilities screen appears, follow the prompts to reinstall the Mac OS. You don't need to erase the boot volume, and you won't need your backup unless something goes wrong. If your Mac didn’t ship with Lion, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
Don't install the Thunderbolt update -- it's defective.

Trying to install iTunes 12.1 for Windows 8.1 (64-bit) and get Itunes error HRESULT: 0x800736B3

Hello,
I am Trying to install iTunes 12.1 for Windows 8.1 (64-bit) and I get an Itunes window with an error that says:
An error occurred during the installation of assembly 'Microsoft.VC80.CRT,type="win32",version'8.0.50727.6195",publicKeyToken="1fc8b3 b9a1e18e3b"processorArchitecture="amd64". Please refer to help and Support for more information.HRESULT: 0x800736B3
I already:
- Uninstalled all old Itunes versions.
- Tried a clean reboot to install the new version,
- Installed the security update’ Microsoft Visual C++ 2005 Service Pack 1 Redistributable Package ATL Security Update’
But I still get the same error.
Can someone help?
Thanks!

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
If you still have trouble you might consider installing the alternate version iTunes 12.1 for Windows (64-bit — for older video cards) where you can download a 64-bit installer for the 32-bit version of iTunes that works with older video cards. This version may also be useful for anyone who is unable to get the 64-bit version of Apple Application Support to install when using the itunes6464setup file, or has trouble with playback of certain video files despite having QuickTime installed.
tt2

HP laserjet 1200 series pcl5 driver for windows 7 64bit and windows 8.1 64bit

Dear
I need
HP laserjet 1200 series pcl5 driver for windows 7 64bit and windows 8.1 64bit
can anyone provide me ? no links to read text, direct solution is welcomed
thanks in all

Hi.
You may download the Universal Print Driver PCL5 below, it is compatible with both Windows 7 or 8 64-bit.
For USB select Plug n Play, for network select Tradiotional Mode and follow the steps by setting a TCP/IP Port with the IP Address of the printer:
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=29790&spf_...
Please let me know of any issuesm
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

CORRECT DRIVER FOR WINDOWS 7 AND HP COLOR LASER JET 4600dn

I'm having a problem with our IT department. My old 4600dn worked great until they started downloading new drivers for Windows 7, which they installed just recently. Now the one he INSISTS I use has only one tray selection.... Auto. I'm trying to print business cards..(absolutely no problem till now).... but he INSISTS that this is the only driver. Then he wants me to choose Pg.....select 1, then MANUAL DUPLEX. That's almost impossible for the printer. I'm almost POSITIVE you have a print driver that will allow me the tray selections I had before he installed Windows 7 and this particular driver. I always used "Tray 1," CURRENT PAGE, it zoomed through the perforated cardstock like a streak!!!! Now, the poor printer is trying to run perforated cardstock through the duplexing unit. Out of 10 pages of cards, I ended up with 1 front printed and 9 pieces of cardstock that stuck in the tray and jammed in the duplexing unit. Is there a CORRECT print driver for this particular printer that will allow all my normal functions to be visible and viable? I don't have the model, nor serial #, as it is work printer and I'm at home now, so I can't get on chat. He is hard to get along with and has been playing games this whole time. I found one driver he inadvertantly left a day and a half ago and printed the cards like lightening, as it used to....7 minutes and I had 200 cards for two different staff members. PLEASE HELP! I think he's leading me down a merry path. It also has to be able to duplex fairly heavy graphic pages...and even the driver he accidently left as an option, won't print the graphics. I just KNOW you have a driver with all the options that will allow it to print to Windows 7 Operating System with all the former options. HELLLLLLLP!
Thanks sooooo much!
Kathi T.
[text removed for privacy]

Any suggestions re correct driver for windows 7 and HP 4600dn?

Drivers and software Hp deskjet 2050 j510a All-in-wonder for Windows 8 Pro x64

Hi,
from when I update my system with Windows 8 Pro I can' t use the printer Hp Deskjet 2050 J510a.
I downloaded the latest version of drivers and software for Windows 8 Pro 64 bit:
DJ2050_J510_Basicx64_1313.exe
The application give me at the and of installation the message:
"installation not completed"
and in details I can see:
"Installation error. Operative system not supported. This software can be installed only in Windows XP, Vista, Seven. Change operative system or install the printer in another computer."
The printer as been recognized from the system, and in panel control I can see it, but when I print any page the printer make only half print and than show me a message of " not original or used printer cartridges, press OK to continue or cancel do delate the print" but the print cannot be completed untill the end.
Cartridges are original; I tested the the printer too in an another computer with different operative system: the printer work correctly.
Thanks for your attention

Hello kamran554,
I understand you are looking for the driver to download for your Deskjet 2050 J510a for Windows 8 64bit.
I have located the correct driver for you to download below.
Please click the link to download and install.
HP Deskjet Full Feature Software and Drivers
Good luck to you!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Use external drive for windows and mac

Hello,
I just bought a external 320Gb Western Digital Drive. I would like to use
the drive for windows and mac.I will not like to make partation on the drive
to use it on both operating systems. Is there any formating system with which i can use in both operating systems? I would like to use time machine feature on that drive also.
Thanx.

If you want to use a disk for both PC/Mac file storage and Time Machine, you will have to create two partitions. Partitioning is sort of like creating multiple virtual disks on the same physical disk. One partition should be formatted for PC (which the Mac can also use) and the other should be formatted for HFS+ (Mac only) which is what Time Machine requires. The Disk Utility application makes partitioning and formatting very easy.

I am semi-retiring my old mac mini and want to use it as a hard drive for my macbook pro. Does anyone know how to do this?

I am semi-retiring my old mac mini and want to use it as a hard drive for my macbook pro. Does anyone know how to do this?

1. Remove the drives, install them in external enclosures.
2. Use a Firewire cable to connect to your computer. Boot the mini into Target Disk Mode - Transferring files between two computers using FireWire

I am confused by the installation step that requires you to create a bootable USB drive for windows installation. What is the ISO image and why has it selected my Passport backup drive as the destination disc?

In the bootcamp installation it asks me to create a bootable USB drive for Windows Installation. To do so, I must choose an ISO image. What is that? When I click "choose" I don't understand the options presented. Is this the destination of the partition or where Windows will reside on the Mac? Why does it also indicate the the destination disk si my WD Passport Back up drive?

OK, so I have an apple superdrive hooked up to my mini (along with my Passport back up drive). I also have the discs for both 64bit and 32bit Windows along with the product key. I am still not sure what to do when faced with the options after "choose".

Uninstalling the drivers and programs for Windows 7 SP1 64 bit of the OfficeJet 7410 All-In-One

Hi
Which utility should be used to properly and completely uninstall the drivers and programs for Windows 7 SP1 64 bit installed with the OfficeJet 7410 All-In-One printer?
Thanks
Bye
balubeto

Hi @balubeto
I located a software removal utility for you but if you have other HP printers or scanners you may perform the more basica uninstall.
Software and Driver Removal Utility
Uninstalling the Printer Software (more basic uninstall)
I hope this resolves your inquiry.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Please cancel this order immediately and refund my credit card. This product is for Windows only. I run a Mac. You did not state in your advert that this was windows only. This transaction has cost me money as there will be a charge for the Canadian excha

AD015968571 : Please cancel this order immediately and refund my credit card. This product is for Windows only. I run a Mac. You did not state in your advert that this was windows only. This transaction has cost me money as there will be a charge for the Canadian exchange fee.
No other way to contact Adobe. All Email undeliverable.

These are user to user forums
Phone support | Orders, returns exchanges
http://helpx.adobe.com/x-productkb/global/phone-support-orders.html
For the link below click the Still Need Help? option in the blue area at the bottom and choose the chat option...
Creative Cloud support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html ( http://adobe.ly/19llvMN )

Lenovo G400s Wireless Connection Limited Access on Windows 7 Ultimate - 32 bit

Just bought Lenovo G400s, install windows 7 ultimate - 32 bit on it.
It turns out the wireless network driver need to install manually, the disc driver that came with laptop was for windows 8.1. So I went to lenovo website, put on the series and download the wirelss network driver which is around 250 MB.
I installed the driver and connect to the wireless network. My office wireless was on security and use static ip. I changed the ipv4 ip static already. It connected for a while, 1-2 second then lost connection. I checked with ping to google, got 2 records of live connection which is very short. After that it try to reconnecting itself again and again with status said "Limited Access"
I search in google, read some forums about problem in different series, so I use another computer go to Intel website to download latest driver. Got it installed, but it's still the same.
I try download broadcom driver, but it's really different and doesn't work at all.
Now I don't know what to do.
Windows 7 Ultimate - 32 bit
Inter(R) Centrino(R) Wireless-N 135
Driver Provider: Intel
Driver Date: 1/26/2014
Driver Version: 15.11.0.7
Digital Signer: Microsoft Windows Hardware Compability Publisher
What makes it weird, although from intel website said the driver date is in 3/21/2014, and the version is 16.11.0, but this information I get from device driver was different.
Here's the intel's website if you're wondering:
_https://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=Wireless+Networking&ProductLine=Intel%C2%AE+Wi-Fi+Products&ProductProduct=Intel%C2%AE+Centrino%C2%AE+Wireless-N+135#&OSVersion=Windows%207%20(32-bit)*&DownloadType=Software%20Applications
Can anyone help me?
Solved!
Go to Solution.

Today I want to install windows 8.1 on it, because the laptop came with windows 8.1 driver disc.
However, I try the wireless connection once again , one final try before I clean install the OS.
It turns out the internet connection is connected. Ping is quite stable, got a small drop. Nonetheless, IT'S CONNECTED!!!
I don't know what happened, I tried thousand ways yesterday and gave up. Today I don't set anything just try connecting with static IP set the ipv4 just like I did yesterday, and it connects without hassle!! is there a pc fairy or what?
The possible way I can think of is the router's internet connection's got restarted since It's a new day at office.
Despite how it solved still mystery to me, I think I mark this thread as Solved.

X41 wireless driver for windows 7

where can i find a wireless driver for windows 7 on my x41 tablet pc?
The only thing i found on Lenovo's website is for vista, xp, and windows 2000
any help would be greatful!
Thank you!!!
Solved!
Go to Solution.

Give the Vista driver a shot. Some drivers work vice versa.
IT Specialist and Consultant
Lenovo Tablet Evangelist
Current Machines: IdeaCentre A300, ThinkPad Tablet, IdeaPad U410, and Yoga 3 Pro Touch
Deutsche Community Comunidad en Español
Lenovo - the latest in DOtabs, DOpads, DOcentre's, DOstations and DOservers!

Need Palm Bluetooth Wireless Keyboard 3245WW driver for Pre!

Need Palm Bluetooth Wireless Keyboard 3245WW driver for Pre!

Great idea! Unfortunately, there isn't one yet...
Drop Palm a line at the suggestion link below in my signature. I think I'll do the same!
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

X301 and Vodafone and AT&T Wireless WAN (HSPA) Driver for Windows 7 (32-bit, 64-bit)

Similar Messages

Maybe you are looking for