X38 Diamond and P45 Diamond; endless reboots before POST

Hi,
I'm experiencing the same problems with two MSI-boards now, and I have had the same problem with a another MSI P35-based board earlier (belive it was a P35 Premium with a C2Q Q6600 - I replaced the board and the config worked fine with a Gigabyte P35-board).
These system don't share any components.
For the P45 Diamond I use a C2Q Q9300, 4 GB of Crucial PC6400 DDR2, Asus GeForce 8600GTS and WD 250 GB SATA HDD. I was able to build the system, install the software and use it for about a week before the trouble starts. When I power the system, fans starts spinning, before it restarts it self over and over again.
On this system I have tried to change the PSU from a Antec 500W to a Corsair 450W, without any difference...
The X38 Diamond system runs with a C2D E4200, 4 GB of Corsair XMS3-1800, GeForce 7800GTX, 250 GB WD SATA HD and a 900W Fortron Source Epsilon PSU. The problem is the same: I was able to get the system up running, install Windows and drivers, and after a few days the problems start. I turn on the system, and after a few seconds it turn itself off, then on, then off and so it goes.
Other than being in the same room, and buildt by me, these systems don't have anything in common. I have used different power-sockets also, on seperate circuits, and that itself should not be a problem.
Tried resetting CMOS on the boards, disconnecting HDD and other stuff that ain't really needed to POST... As I said. At first these systems worked fine, but after a few days of use, problems started. The P45 Diamond-system was buildt some months ago and they put away because of the problems, and now the similar problems with the X38-based setup...

Quote
For the P45 Diamond I use a C2Q Q9300, 4 GB of Crucial PC6400 DDR2, Asus GeForce 8600GTS and WD 250 GB SATA HDD.
The P45 Diamond does not support DDR2 memory modules. Can you please verify the info you gave? Also, what is the onboard BIOS Version?
Quote
The X38 Diamond system runs with a C2D E4200, 4 GB of Corsair XMS3-1800, GeForce 7800GTX, 250 GB WD SATA HD and a 900W Fortron Source Epsilon PSU. The problem is the same: I was able to get the system up running, install Windows and drivers, and after a few days the problems start. I turn on the system, and after a few seconds it turn itself off, then on, then off and so it goes.
Please clear CMOS with main A/C power cable removed from PSU, remove all memory modules but one and try to start the system again. Please post a link to the Corsair Datasheet of those memory modules. And also, the onboad BIOS Version would be interesting to know.

Similar Messages

Does a X38 Diamond supports ddr2 Ram of 1066 bus

Will a MSI X38 Diamond motherboard will support ddr2 ram of 1066 bus from G.SKILL manufacturer.
and if not then is there any other MSi mother board with x38 chipset that will do
plz let me

Have a look here:
http://global.msi.com.tw/index.php?func=proddesc&prod_no=1328&maincat_no=1&cat2_no=170
Quote
Main Memory
• Supports four unbuffered DIMM of 1.5 Volt DDR3 SDRAM
• Supports up to 8GB memory size.
• Supports dual channel DDR3 memory architecture.
• Supports DDR3 800/1066/1333 memory interface.
DDR2 memory modules are not supported.
Quote
and if not then is there any other MSi mother board with x38 chipset that will do
No, however, the X48C Platinum supports DDR2 & DDR3 modules:
http://global.msi.com.tw/index.php?func=proddesc&prod_no=1393&maincat_no=1&cat2_no=170

HT201413 I have done everything listed here (Error code 9) and nothing is working. My phone is stuck in endless reboot and i need it! Someone please help! I already completely uninstalled Norton.

My phone is stuck in endless reboot mode. I have it in recovery mIode now. My computer wont let me reset it and i have done everything suggested. I completely uninstalled my security (Norton) so I dont see how removing and changing ports will help. Im getting error code 9. Besides, I dont know how to configure ports and let itunes pass things. Please help! Thanks!

My phone is stuck in endless reboot mode. I have it in recovery mIode now. My computer wont let me reset it and i have done everything suggested. I completely uninstalled my security (Norton) so I dont see how removing and changing ports will help. Im getting error code 9. Besides, I dont know how to configure ports and let itunes pass things. Please help! Thanks!

Please help my ipad just rebooted after me turnng it on and it is in wat people call a endless reboot mode where it wont start up please help

please help my ipad just rebooted after me turnng it on and it is in wat people call a endless reboot mode where it wont start up please help

Hi Patkid27,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
iOS: Not responding or does not turn on
http://support.apple.com/kb/ts3281
Cheers,
- Judy

Since upgrading to OS 8.0.2 my ipad2 freezes, slows down, safari takes forever to open, the celluar network goes to No Service and the only way to fix it is to reboot it and this takes longer than before. Has Microsoft taken over Apple software?

SInce upgrading to OS 8.0.2 my ipad 2 freezes, slows down, safari takes forever to open pages, cellular network goes to No Service requiring a reboot (and this takes longer than before), in summary, I now have a fancy paperweight, i used to love my ipad. I feel as if Microsoft has taken charge of the Apple Software Division.

Sorry if someone sees this post in a different thread; Just want to get some additional exposure.. Who knows, maybe someone from Apple will take note..
The glitchy, unresponsive, slow and outright crashes are something you would expect in a less superior product. I paid what I consider a premium because of the perceived integrity of the company and quality of their products. I am not going to go as far to say Apple ***** and so do their products; but they have to to a better job of acknowledging problems and providing recourse. Right now, it "feels" like they don't care about existing customers. I am not sure of the exact #'s, but I believe products like the Ipad2 represent a significant population of their existing Ipad product base.
So what is my specific rant; If Apple is going to take a long time, or worst, NOT fix the problems introduced in IOS 8 for IPAD 2, give us the option of going back to IOS 7. I would say most everyone was extremely happy with their product running under that OS and would migrate back in a heartbeat. By blocking this option, it feels like Apple is saying that the only recourse is to live with crappy performance, wait forever without any real news, or throw away your Ipad 2 and buy a newer model. Right now this is 100% completely unacceptable, and I, as will thousands of others, will watch how this unfolds when we do buy new products. Most technology products only have short, finite lifespan and I would think it is at very least very important to Apple to retain customer base in a highly competitive marketplace. I'm done...

MBP rebooting itself and then endlessly rebooting.

Hi All,
I'm having an interesting problem with my Santa Rosa MBP, which is about 4 months old. Twice now after using Toast 9 to burn DVD's, my computer has shut it self off and then continues to reboot endlessly. This occurs after I've written and verified a disc and choose to mount it, once I click "mount it" said problem occurs. I then do a hard shut off, and reboot normally.
I've also been experiencing system freezes while running disk utility to verify/or repair my externals, and my internal. I'm also experiencing occasional system freezes when using coverflow in iTunes.
I take good care of my computer, repair permissions regularly, and just recently ran the apple hardware test which found no problems.
Any ideas? Thanks for looking.

here is a list of some console messages (some referencing another problem i'm having where I can't seem to eject my FW 400 drive on occasion.)
Pertaining to system rebooting:
4/25/08 12:22:51 PM Software Update[1718] Package Authoring Error: installation-check results requires a message
4/25/08 12:22:51 PM Software Update[1718] Package Authoring Error: installation-check results requires a message
4/25/08 12:22:51 PM Software Update[1718] Package Authoring Error: installation-check results requires a message
4/25/08 12:22:51 PM Software Update[1718] Package Authoring Error: installation-check results requires a message
4/25/08 12:22:51 PM Software Update[1718] Package Authoring Error: installation-check results requires a message
4/25/08 12:23:25 PM installdb[1724] Opened receipt database on '/' with schema 17.
4/25/08 12:23:26 PM Software Update[1718] JavaScript error "Undefined value" while running "_choice_suvisible"
4/25/08 12:23:26 PM Software Update[1718] _choice_suvisible returned error: Undefined value
4/25/08 1:36:58 PM /usr/sbin/ocspd[1754] starting
4/25/08 1:37:42 PM Finder[99] NSOpenGLAutoscaleBounds=NO
4/25/08 1:38:20 PM QuickTime Player[1756] NSOpenGLAutoscaleBounds=NO
4/25/08 1:39:04 PM QuickTime Player[1756] CGImageDestinationAddImageFromSource image 0 of source is nil
4/25/08 1:39:04 PM QuickTime Player[1756] CGImageDestinationFinalize image destination does not have enough images
4/25/08 1:39:04 PM [0x0-0x74074].com.apple.quicktimeplayer[1756] Fri Apr 25 13:39:04 phaedruss-macbook-pro.local QuickTime Player[1756] <Error>: CGImageDestinationAddImageFromSource image 0 of source is nil\n
4/25/08 1:39:04 PM [0x0-0x74074].com.apple.quicktimeplayer[1756] Fri Apr 25 13:39:04 phaedruss-macbook-pro.local QuickTime Player[1756] <Error>: CGImageDestinationFinalize image destination does not have enough images\n
4/25/08 2:46:08 PM /Applications/QuickTime Player.app/Contents/MacOS/QuickTime Player[1783] _RemoveTimeTask(), the current time manager task 0x1cd5070c being removed is also currently executing its tmAddr routine, so unexpected things may result ( Radar #4555679 ).
4/25/08 3:06:42 PM QuickTime Player[1783] NSOpenGLAutoscaleBounds=NO
4/25/08 3:14:47 PM /usr/sbin/ocspd[1796] starting
4/25/08 3:15:43 PM /usr/sbin/spindump[1799] process 1798 is being monitored
Messages related to problem drive:
4/25/08 4:36:48 PM mds[30] (/Volumes/NIETZSCHE/.Spotlight-V100/Store-V1/Stores/90662AA3-B0A7-4B23-864C-680 900DCA8AB)(Error) IndexCI in ContentIndexOpenBulk:Could not open /Volumes/NIETZSCHE/.Spotlight-V100/Store-V1/Stores/90662AA3-B0A7-4B23-864C-6809 00DCA8AB/live.2.; needs recovery
4/25/08 4:36:48 PM mds[30] (/Volumes/NIETZSCHE/.Spotlight-V100/Store-V1/Stores/90662AA3-B0A7-4B23-864C-680 900DCA8AB)(Error) IndexCI in recoverIndex:recover canceled (0.)
This one disturbs me - what does it mean?
4/25/08 3:15:54 PM [0x0-0x7f07f].com.adobe.AfterEffects[1798] I'm the snoop.

Satellite L500-1DT: HDD Recovery of Win 7 is stuck in endless reboot loop

This is a detailed bug report so please bear with me.
If you can help, or can confirm you've had the same happen to you, I'll be grateful.
I've owned several Toshiba laptops before and I even used to work for Toshiba so rest assured I like the machine. But I've got a problem with its recovery software. I just bought a laptop, Satellite L500-1DT with Windows 7 64 bit, on behalf of a non-techie who lives elsewhere. Since I know from experience that I will occasionally have to field panic calls along the lines of "it's become too slow", "how do I get rid of the accumulated junk", "maybe it's got a virus" and so on, the first thing I checked was the automatic recovery, i.e. how to bring the HD back to "as new" state.
So I booted into the machine, answered the questions until I got into the OS proper, and then ran the "make a recovery DVD" program. Double layer DVD verified ok. With the freshly made DVD, I swapped the supplied HD for a spare I had (much smaller: only 40 GB instead of 320) and booted the rescue DVD hoping that it would remake me a clean system on the blank drive.
It did repartition the drive according to its scheme, with more or less half the space for Windows and the other half for Data including the recovery files. It did install the system in the Windows partition. It then rebooted into the installed Windows 7 to finalize the installation. There, trouble began: an endless loop of reboots for hours until I stopped it.
Loop:
* reboot
* black screen with bright 4-colour windows logo "starting windows"
* black screen with light blade and "setup is preparing your computer for first use"
* blue "welcome" white screen with "please wait" and horizontal bar with green blob, saying "Finishing the installation may take several minutes. Please dont interrupt or shutdown the computer!"
* blue screen saying it's shutting down
Repeat the above forever.
I have seen it reboot way over 10 times over the course of several hours. And every time it pretends it's the first time it does that. Surely that's not normal!
I tried stopping it with ctrl-alt-del and task manager but the white screen would go on top of even the task manager, making it hard to kill any processes or even inspect what they were. I stopped it by holding down the power button until it switched off. Then when it rebooted it said if I wanted safe mode. I tried that. It went into the routine above and at some point it said it couldn't proceed with the installation if it was in safe mode. So it rebooted into regular mode and then... finished! It finally broke out of the endless loop!
Then it asked me all the usual questions about language, registration etc, as it had done the first time I had turned it on. This seemed good. I finally got back into a newly installed OS and all seemed fine, except I later discovered that some programs that were there before were not installed.
With bravery bordering stupidity (*) I even re-did the procedure on the supplied hard disk instead of my spare one: first I nuked the windows partition, then I did rescue from the HD (with F8), not with the DVD I had made. Result: similar rigmarole, with endless reboots.
After I stopped it, it sort-of-worked, as above, but now some other programs were missing, notably the Toshiba DVD player.
(*) motivated by: better try this now, with the computer here and all my tools and other computers ready at hand, than when the computer is away at its owner's home and that's the only thing left to try with me at the other end of a phone line. Been there before.
Now, that specific one (DVD player) I could download from the support page and it installed fine; but what else might be missing or not working that I didn't notice? Clearly the restore process isn't working as it should.
Am I the first or only one to whom this happens? Am I doing anything wrong? Is there anything else I should try?
I need to make sure this restore procedure works flawlessly while I still have the computer in my hands. If it doesn't, there's no chance I'm going to be able to do a remote reinstall for my non-techie once I am asked to clean up the laptop over the phone a few months from now.
Thanks in advance
[Update: while looking for the right place where I could post this I found that other people are reporting the same problem. It's definitely a bug in the distributed recovery software for W7-64, not an isolated problem of my machine. See for example
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=49421&tstart=0 where user kwarc is describing the same symptoms with a Satellite L505.

I am glad to report some unexpected SUCCESS!
I left the computer at what it was doing when I wrote the previous
post. I came back to it an hour later or so (I had stopped counting
the reboots, though occasionally I'd hear that typical chime from the
other room, saying it was doing one more cycle) and I noticed
something slightly different: the white screen with "finishing the
installation may take several minutes" had a blue blob, not a green
blob, in the progress bar, and the blob was rectangular rather than
rounded. Very odd! Something different had happened, like a change of
theme. And a little while after that, the process really finished and
I got to the white screen that asks about what language etc etc, like
when I first turned on the new computer.
Great!
All I can conclude from this experience:
Even a reinstall that works will DEFINITELY involve many reboots that
seem to be getting nowhere. Apparently, progress is being made, even
though it looks like the process is stuck in a loop of reboots.
It would just be nice if it said something like "Before I finish
restoring, I'm going to have to reboot 26 times, please hang on; now
doing cycle 8 of 26". (Numbers are made up.) It doesn't, but just
knowing about it is helpful.
Perhaps worth redoing the install once more and making a note of how
long it really takes from beginning to end when it does work.
I still don't know if the process I described in the first post was
really stuck because of some other error or whether it would have
ended eventually. If I wanted to be really sure I could re-restore
everything on that hard disk once more.
I have no idea whether wiping all partitions from the disk before
reinstalling did any good or not: it shouldn't have made a difference
since, as I said, I noticed that the first thing the restore program
did was redo all the partitions itself. On the other hand we have
experimental proof that the restore can work on a HD without any
partitions.
Thanks again PauPau---the most useful thing you said, for me, was the
data point that for you it had worked. That's what made me try again
and leave the computer on indefinitely through the innumerable
reboots, just in case.
I'll repost a definitive answer on how long a successful restore
process should take once I get round to redoing it on the supplied 320
GB HD.

My Macbook Pro became noisy and slow after I reboot it. Any Help pls

I just bought my Macbook Pro last month here in Japan, and it is working well until one time I cannot login my username and password because whenever I type my username, an Arabic-like characters appear. Then using my iphone, I searched on the internet and luckily found answer to my problem. Macbook Pro users shared their same problems, and they mentioned about "rebooting" (switch on and hold Shift). then I tried it and resolved my problem.. But when I was about to use my mac, i noticed a noisy fan and my mac became slow.(which I never experiece before eventhough I have poor connection, it still run fast). And what I hate most is it always `reload/ buffer`.. A rainbow color ball always appear and it will reamin reloading for a long time.. one time, I leave it relaoding and try to cook dinner, expecting to fnish relaoding after i cook, but it didnt change, it is still relaoding (with rainbow color ball) .. What can I do with this problem? what im doing with my Mac is purely internet, movies (no downlad, just watching free movies, but not always), and manage my own site.. I hope and expect a solution from you guy.. thank you...

Try the usual things. Reset the SMC. Reset the PRAM. Repair Disk Permissions. Clear all the caches. Check the Activity Monitor to see if any processes are hogging cpu/ram. Make sure everything is up to date. Check the temperatures with a program like Temperature Monitor or iStatPro to make sure its not overheating, and to find out what speed the fans are running at.

Safari hangs and forces a system reboot

This happens more frequently recently. Out of the blue, Safari (v8.0.3) under OS X 10.10.2 freezes OS X completely and the system reboots. It happens on simple HTML only websites that don't require any scripts - e.g. forums. The screen resolution appears to be lowered when logging back in, but once the system has loaded everything seems to be normal (even Safari remembers all the sites).
Aside from the ongoing WiFi issues, Yosemite is the first Apple OS that seems to crash frequently on me...
Who else is experiencing these issues?
2012 MacBook Pro Retina
16 Gb, 512 Gb SSD

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
The test works on OS X 10.7 ("Lion") and later. I don't recommend running it on older versions of OS X. It will do no harm, but it won't do much good either.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of it have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message. See, for example, this discussion.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. Try to test under conditions that reproduce the problem, as far as possible. For example, if the computer is sometimes, but not always, slow, run the test during a slowdown.
You may have started up in "safe" mode. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(1236 ' 0.5 0.25 10 1000 15 5120 1000 25000 1 1 0 100 ' 51 25600 4 10 25 5120 102400 1000 25 1000 80 40 500 300 85 25 20480 262144 20 2000 524288 604800 5 );k=({Soft,Hard}ware Memory Diagnostics Power FireWire Thunderbolt USB Bluetooth SerialATA Extensions Applications Frameworks PrefPane Fonts Displays PCI UniversalAccess InstallHistory ConfigurationProfile CFBundleIdentifier 'com\.apple\.' -\\t N\\/A 'AES|atr|udit|msa|dnse|ax|ensh|fami|FileS|fing|ft[pw]|gedC|kdu|etS|is\.|alk|ODSA|otp|htt|pcas|ps-lp|rexe|rlo|rsh|smb|snm|teln|upd-[aw]|uuc|vix|webf' OSBundle{Require,AllowUserLoa}d 'Mb/s:per sec:ms/s:KiB/s:%:total:MB:total' 'Net in:Net out:I/O wait time:I/O requests:CPU usage:Open files:Memory:Mach ports:File opens:Forks:Failed forks:System errors' 'tsA|[ST]M[HL]' PlistBuddy{,' 2>&1'}' -c Print' 'Info\.plist' );f=('\n%s'{': ','\n\n'}'%s\n' '\nRAM details\n%s\n' '%s %s\n' '%s\n'"${k[22]}"'%s\n' {Privacy,Mode}': %s\n' '\n   ...and %s more line(s)\n' 'RSSI: %s\nNoise: %s\nTx rate: %s\n' '\nContents of %s\n   '"${k[22]}"'mod date: %s\n   '"${k[22]}"'checksum: %s\n%s\n' '%d MB: %s\n' );c=(879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 2636415542 3694147963 1233118628 2456546649 2806998573 2778718105 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 3374894509 1051159591 892310726 1707497389 523110921 2883943871 3873345487 );s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[4]} ' s/:$//;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[9]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' BEGIN { FS=":";if(system("sw_vers -productVersion|grep -q ^10\.1")) d="^'"${k[21]}"'launch(d\.peruser\.[0-9]+|ctl\.(Aqua|Background|System))$";} { if($2~/[1-9]/) { $2="status: "$2;printf("'"${f[4]}"'",$1,$2);} else if(!d||$1!~d) print $1;} ' ' { sub(/ :/,"");print|"tail -n'${p[10]}'";} ' ' NR==2&&$4<='${p[7]}' { print $4;} ' ' ($1~"wir"&&$2>'${p[22]}')||($1~/P.+ts:/&&$2>'${p[19]}') { print $1" "int($2);} ' '/YLD/s/=/ /p' ' { q=$1;$1="";u=$NF;$NF="";gsub(/ +$/,"");print q":"$0":"u;} ' ' /^ {6}[^ ]/d;s/:$//;/([^ey]|[^n]e):/d;/e: Y/d;s/: Y.+//g;H;${ g;s/ \n (\n)/\1/g;s/\n +(M[^ ]+)[ -~]+/ (\1)/;s/\n$//;/( {8}[^ ].*){2,}/p;} ' 's:^:/:p;' ' !/ /{print};END{if(NR<'{${p[12]},${p[13]}}')printf("^'"${k[21]}"'.+")} ' '|uniq' ' 1;END { if(NR<'{${p[14]},${p[21]}}') printf("^/[Sp].+|'${k[21]}'");} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:.+//p;' '&&echo On' '/\.(bundle|component|framework|kext|mdimporter|plugin|qlgenerator|saver|wdgt)$/p' '/\.dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".","");print $0"$";} END { split("'"${c[*]}"'",c);for(i in c) print "\t"c[i]"$";} ' ' /^\/(Ap|Dev|Inc|Prev)/d;/((iTu|ok).+dle|\.(component|mailbundle|mdimporter|plugin|qlgenerator|saver|wdgt))$/p;' ' $2=="=" { gsub(/[()"]/,"",$3);print $3;} ' ' /^\// { sub("/dev/","",$1);printf("%s: %s\n",$1,$9);} ' '>&-||echo No' '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[2]}'{$2=$2-1;print}' ' BEGIN { M1='${p[16]}';M2='${p[18]}';M3='${p[8]}';M4='${p[3]}';} !/^A/{next};/%/ { getline;if($5<M1) o["CPU"]="CPU: user "$2"%, system "$4"%";next;} $2~/^disk/&&$4>M2 { o[$2]=$2": "$3" ops/s, "$4" blocks/s";next;} $2~/^(en[0-9]|bridg)/ { if(o[$2]) { e=$3+$4+$5+$6;if(e) o[$2]=o[$2]"; errors "e"/s";next;};if($4>M3||$6>M4) o[$2]=$2": in "int($4/1024)", out "int($6/1024)" (KiB/s)";} END { for(i in o) print o[i];} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/)||(/v6:/&&$2!~/A/) ' ' $1=="op" {m=$3};$1~"lN" {N=$2};$1~"lR" {S=$2};$1~"Tx" {T=$2};$1~/^st/ {s=$2};$1~"li"&&$3!~"wpa2" {printf("'"${f[5]}"'",toupper($3))};END { if(S*N*T&&(S-N<'${p[5]}'||T<'${p[20]}')) printf("'"${f[8]}"'",S,N,T);if(s~/^r/&&m!~/^st/) printf("'"${f[6]}"'",m);} ' ' BEGIN { FS=":";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1;} ' ' BEGIN { split("'"${p[1]}"'",m);FS=":";} $2<=m[$1]{next} $1<9 { o[$1]=o[$1]"\n   "$3" (UID "$4"): "$2;} $1==9&&$5!~"^/dev" { o[$1]=o[$1]"\n   "$3" (UID "$4") => "$5" (status "$6"): "$2;} $1==10&&$5 { p="ps -c -ocomm -p"$5"|sed 1d";p|getline n;close(p);if(n) $5=n;o[$1]=o[$1]"\n   "$5" => "$3" UID ("$4"): "$2;} $1~/1[12]/ { o[$1]=o[$1]"\n   "$3" (UID "$4", error "$5"): "$2;} END { n=split("'"${k[27]}"'",u,":");for(i=n+1;i<n+5;i++)u[i]=u[2];split("'"${k[28]}"'",l,":");for(i in o) print "\n"l[i]" ("u[i]")\n"o[i];} ' ' /^ {8}[^ ]/{print} ' ' BEGIN { L='${p[17]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n   "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n   [N/A]";"cksum "F|getline C;split(C, A);C=A[1];"stat -f%Sm "F|getline D;"file -b "F|getline T;if(T~/^Apple b/) { f="";l=0;while("'"${k[30]}"' "F|getline g) { l++;if(l<=L) f=f"\n   "g;};};if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F"\n   '"${k[22]}"'"T;printf("'"${f[9]}"'",F,D,C,f);if(l>L) printf("'"${f[7]}"'",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' 's/^.{52}(.+) <.+/\1/p' ' /id: N|te: Y/{i++} END{print i} ' ' /kext:/ { split($0,a,":");p=a[1];k[S]='${k[25]}';k[U]='${k[26]}';v[S]="Safe";v[U]="true";for(i in k) { s=system("'"${k[30]}"'\\ :"k[i]" \""p"\"/*/I*|grep -qw "v[i]);if(!s) a[1]=a[1]" "i;};if(!a[2]) a[2]="'"${k[23]}"'";printf("'"${f[4]}"'",a[1],a[2]);next;} !/^ *$/ { p="'"${k[31]}"'\\ :'"${k[20]}"' \""$0"\"/*/'${k[32]}'";p|getline b;close(p);if(b~/ /||b=="") b="'"${k[23]}"'";printf("'"${f[4]}"'",$0,b);} ' '/ en/!s/\.//p' ' NR>=13 { gsub(/[^0-9]/,"",$1);print;} ' ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?'${k[32]}'$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ / [VY]/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' '/^find: /!p;' ' /^p/{ s/.//g;x;s/\nu/:/;s/(\n)c/\1:/;s/\n\n//;p;};H;' ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */   /;p;' ' s/^.+ |\(.+$$//g;p;' '1;END{if(NR<'${p[15]}')printf("^/(S|usr/(X|li))")}' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR|^s/d;s/^.+: //p;' ' $3~/^[1-9][0-9]{0,2}(\.[1-9][0-9]{0,2}){2}$/ { i++;n=n"\n"$1"\t"$3;} END{ if(i>1)print n} ' s/{'\.|jnl: ','P.+:'}'//;s/ +([0-9]+)(.+)/\2 \1/p' ' /es: ./{ s/^.+://;b0'$'\n'' };/^ +C.+ted: +[NY]/H;/:$/b0'$'\n'' d;:0'$'\n'' x;/: +N/d;s/\n.+//p;' ' 1d;/:$/b0'$'\n'' $b0'$'\n'' /(D|^ *Loc.+): /{ s/^.+: //;H;};/(B2|[my]): /H;d;:0'$'\n'' x;/[my]: [AM]|m: I.+p$|^\/Vo/d;s/(^|\n) [ -~]+//g;s/(.+)\n(.+)/\2:\1/;s/\n//g;/[ -~]/p;' 's/$/:(0|-(4[34])?)$/p' '|sort'{'|uniq'{,\ -c},\ -nr} ' s/^/'{5,6,7,8}':/;s/ *: */:/g;p;' '/e:/{print $2}' ' /^[(]/{ s/....//;s/$/:/;N;/: [)]$/d;s/\n.+ ([^ ]+).$/\1/;H;};${ g;p;} ' 's/:.+$//p' '|wc -l' /{\\.{kext,xpc,'(appex|pluginkit)'}'\/(Contents\/)?'Info,'Launch[AD].+'}'\.plist$/p' 's/([-+.?])/\\\1/g;p' 's/, /\'$'\n/g;p' ' BEGIN{FS=":"} { printf("'"${f[10]}"'",$1/1048576,$2);} ' ' /= D/&&$1!~/'{${k[24]},${k[29]}}'/ { getline d;if(d~"t") D=D"\n"$1;} END { print D;} ' ' NR>1&&$3!~/0x|\.([0-9]{3,}|[-0-9A-F]{36})$/ { print $3":"$2;} ' '|tail -n'${p[6]} ' $1>1 { $NF=$NF" x"$1;} /\*/ { if(!f) f="\n\t* Code injection";} { $1="";} 1;END { print f;} ' ' s/.+bus /Bus: /;s/,.+[(]/ /;s/,.+//p;' ' { $NF=$NF" Errors: "$1;$1="";} 1 ' ' 1s/^/\'$'\n''/;/^ +(([MNPRSV]|De|Li).+|Bus): ./d;s/:$//;p;' 's/,.+"//p' '|grep -q e:/' '/[^ .]/p' '{ print $1}' ' BEGIN{ FS=": "} /^C/ { getline t;if(a[split(t,a)]) print $2;} ' ' 1s/^/\'$'\n''/;3,4d;$d;/^ +D|Of|Fu| [0B]/d;s/^ {4}|:$//g;p;' ' BEGIN { FS=":";} NR==1 { print "\n"$1"\n";} /:$/ { l=$1;next;} $1~"S"&&$2!~3 { getline;next;} /^ {6}I/ { i++;sub(/,.+/,"");L[i]=l$2;if(i=='${p[24]}') nextfile;} END { for(j=0;j<i;j++) print L[i-j];} ' ' /services =/,/[\}]/!d;/[=\}]/!p ' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab kextfind top pkgutil "${k[30]}\\" echo cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom 'mdfind -onlyin' env pluginkit scutil 'dtrace -q -x aggsortrev -n' security sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e netstat mdls route egrep 'dscl . -read' );c2=(${k[21]}loginwindow\ LoginHook ' /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'" 'L*/Ca*/'${k[21]}'Saf*/E* -d 2 -name '${k[32]} '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' -i '-nl -print' '-F \$Sender -k Level Nle 3 -k Facility Req "'${k[21]}'('{'bird|.*i?clou','lsu|sha'}')"' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$Message' -k Sender kernel -k Message CRne '0xdc008012|calling|(mplet|nabl)ed|ry HD|safe b' -k Message CReq 'bad |Can.t l|corru|dead|fail|GPU |hfs: Ru|inval|Limiti|v_c|NVDA|pagin|Purg|error|Refus|TCON|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o%cpu,comm,ruid' "' syscall::recvfrom:return {@a[execname,uid]=sum(arg0)} syscall::sendto:return {@b[execname,uid]=sum(arg0)} syscall::open*:entry {@c[execname,uid,copyinstr(arg0),errno]=count()} syscall::execve:return, syscall::posix_spawn:return {@d[execname,uid,ppid]=count()} syscall::fork:return, syscall::vfork:return, syscall::posix_spawn:return /arg0<0/ {@e[execname,uid,arg0]=count()} syscall:::return /errno!=0/ {@f[execname,uid,errno]=count()} io:::wait-start {self->t=timestamp} io:::wait-done /self->t/ { this->T=timestamp - self->t;@g[execname,uid]=sum(this->T);self->t=0;} io:::start {@h[execname,uid]=sum(args[0]->b_bcount)} tick-10sec { normalize(@a,2560000);normalize(@b,2560000);normalize(@c,10);normalize(@d,10);normalize(@e,10);normalize(@f,10);normalize(@g,10000000);normalize(@h,10240);printa(\"1:%@d:%s:%d\n\",@a);printa(\"2:%@d:%s:%d\n\",@b);printa(\"9:%@d:%s:%d:%s:%d\n\",@c);printa(\"10:%@d:%s:%d:%d\n\",@d);printa(\"11:%@d:%s:%d:%d\n\",@e);printa(\"12:%@d:%s:%d:%d\n\",@f);printa(\"3:%@d:%s:%d\n\",@g);printa(\"4:%@d:%s:%d\n\",@h);exit(0);} '" '-f -pfc /var/db/r*/'${k[21]}'*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag $ -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;' '/S*/*/Ca*/*xpc*' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' /\ kMDItemContentTypeTree=${k[21]}{bundle,mach-o-dylib} :Label "/p*/e*/{aut*,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {/p*,/usr/local}/e*/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/{Lau,Sec}*/*t .launchd.conf" list '-F "" -k Sender hidd -k Nle 3' /Library/Preferences/${k[21]}alf\ globalstate --proxy '-n get default' -I --dns -get{dnsservers,info} dump-trust-settings\ {-s,} '' -n1 '-R -ce -l1 -n5 -o'{'prt -stats prt','mem -stats mem'}',command,uid' -kl -l -s\ / '--regexp --files '${k[21]}'pkg.*' '+c0 -i4TCP:0-1023' ${k[21]}dashboard\ layer-gadgets '-d /L*/Mana*/$USER' '-app Safari WebKitDNSPrefetchingEnabled' '-Fcu +c0 -l' -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' '-F \$Message -k Sender kernel -k Message CReq "'{'n Cause: -','(a und|I/O |jnl_io.+)err','USBF:.+bus'}'"' -name\ kMDItem${k[20]} -T\ hfs '-n get default' -listnetworkserviceorder :${k[20]} :CFBundleDisplayName $EUID {,'/{S*/,}'}'L*/{,Co*/*/*/L*/}{Cache,Log}s $TMPDIR../C -type f -size +'${p[11]}'M -exec stat -f'%z:%N' {} \;' \ /v*/d*/*/*l*d{,.*.$UID}/* '-app Safari UserStyleSheetEnabled' "-o ',\"name\":\"[^\"]+' L*/A*/Fi*/P*/*/a*.json" users/$USER\ HomeDirectory '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' ' -F "\$Time \$Sender \$(RefProc): \$Message" -k Level Nle 3 -k Facility R'{'ne "user|','eq "'}'console" -k Message CRne "^[ }]|deprec|sandbox ex" ' getenv '/ "kMDItemDateAdded>=\$time.now(-'${p[23]}')&&kMDItem'${k[20]}'=*"' -m\ / print\ system );N1=${#c2[@]};for j in {0..19};do c2[N1+j]=SP${k[j]}DataType;done;l=({Restricted\ ,Lock,Pro}files POST Battery {Safari,App,{Bad,Loaded}\ kernel,Firefox}\ extensions System\ load boot\ args FileVault\ {2,1} {Kernel,System,Console}\ log Activity SMC Login\ hook 'I/O per process' 'High file counts' UID Daemons Agents XPC\ cache Startup\ items {Admin,Root}\ access Stylesheet Library\ paths{,' ('{shell,launchd}\)} Font\ issues Firewall Proxies DNS TCP/IP Wi-Fi 'Elapsed time (sec)' {Root,User}\ crontab {Global,User}' login items' Spotlight Memory\ pressure Listeners Widgets Parental\ Controls Prefetching Nets Volumes {Continuity,I/O,iCloud,HID,HCI}\ errors {User,System}\ {caches/logs,overrides} Shutdown\ codes Heat Diagnostic\ reports Bad\ plists Free\ space VM Bundles{,' (new)'} 'Trusted certs ('{system,user}\) );N3=${#l[@]};for i in {0..8};do l[N3+i]=${k[5+i]};done;F() { local x="${s[$1]}";[[ "$x" =~ ^([\&\|\<\>]|$) ]]&&{ printf "$x";return;};:|${c1[30]} "$x" 2>&-;printf "%s \'%s\'" "|${c1[30+$?]}" "$x";};A0() { Q=6;v[2]=1;id -G|grep -qw 80;v[1]=$?;((v[1]))||{ Q=7;sudo -v;v[2]=$?;((v[2]))||Q=8;};v[3]=`date +%s`;date '+Start time: %T %D%n';printf '\n[Process started]\n\n'>&4;printf 'Revision: %s\n\n' ${p[0]};};A1() { local c="${c1[$1]} ${c2[$2]}";shift 2;c="$c ` while [[ "$1" ]];do F $1;shift;done`";((P2))&&{ c="sudo $c";P2=;};v=`eval "$c"`;[[ "$v" ]];};A2() { local c="${c1[$1]}";[[ "$c" =~ ^(awk|sed ) ]]&&c="$c '${s[$2]}'"||c="$c ${c2[$2]}";shift 2;local d=` while [[ "$1" ]];do F $1;shift;done`;((P2))&&{ c="sudo $c";P2=;};local a;v=` while read a;do eval "$c '$a' $d";done<<<"$v";`;[[ "$v" ]];};A3(){ v=$((`date +%s`-v[3]));};B1() { v=No;! ((v[1]))&&{ v=;P1=1;};};eval "`type -a B1|sed '1d;s/1/2/'`";B3(){ v[$1]="$v";};B4() { local i=$1;local j=$2;shift 2;local c="cat` while [[ "$1" ]];do F $1;shift;done`";v[j]=`eval "{ $c;}"<<<"${v[i]}"`;};B5(){ v="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`egrep -v "${v[$1]}"<<<"$v"|sort`;};eval "`type -a B7|sed '1d;s/7/8/;s/-v //'`";C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { B4 0 0 63&&C1 1 $1;};C4() { echo $'\t'"Part $((++P)) of $Q done at $((`date +%s`-v[3])) sec">&4;};C5() { sudo -k;pbcopy<<<"$o";printf '\n\tThe test results are on the Clipboard.\n\n\tPlease close this window.\n';exit 2>&-;};for i in 1 2;do eval D$((i-1))'() { A'$i' $@;C0;};';for j in 2 3;do eval D$((i+2*j-3))'() { local x=$1;shift;A'$i' $@;C'$j' $x;};';done;done;trap C5 2;o=$({ A0;D0 0 N1+1 2;D0 0 $N1 1;B1;C2 27;B1&&! B2&&C2 28;D2 22 15 63;D0 0 N1+2 3;D0 0 N1+15 17;D4 3 0 N1+3 4;D4 4 0 N1+4 5;D4 N3+4 0 N1+9 59;D0 0 N1+16 99; for i in 0 1 2;do D4 N3+i 0 N1+5+i 6;done;D4 N3+3 0 N1+8 71;D4 62 1 10 7;D4 10 1 11 8;B2&&D4 18 19 53 67;D2 11 2 12 9;D2 12 3 13 10;D2 13 42 70 101 25;D2 65 6 76 13;D2 45 20 52 66;D4 66 7 37 14;D4 17 8 15 38;D0 9 16 16 77 45;C4;B2&&D0 35 49 61 75 76 78 45;B2&&{ D0 28 17 45;C4;};D0 12 40 54 16 79 45;D0 12 39 54 16 80 45;D4 31 25 37 15&&{ B4 0 8 103;B4 8 0;A2 18 74;B6 8 0 3;C3 32;};B2&&D4 19 21 0;B2&&D4 40 10 42;D2 2 0 N1+19 46 84;D2 44 34 43 53;D2 25 22 20 32;D2 33 0 N1+14 51;D4 69 29 35 104 75 96;D4 70 29 36 104 75 96;D2 34 21 28 35;D4 35 27 29 36;A1 40 59 81;B3 18;A1 33 60 82;B8 18;B4 0 19 83;A1 27 32 39&&{ B3 20;B4 19 0;A2 33 33 40;B3 21;B6 20 21 3;};C2 36;D4 50 38 5 68;B4 19 0;D5 37 33 34 42;B2&&D4 46 35 45 55;D4 38 32 31 43;B2&&D4 59 4 65 76 91;D4 63 4 19 44 75 95 96;B1&&{ D4 53 5 55 75 69&&D4 51 6 58 31;D4 56 5 56 97 75 98&&D0 0 N1+7 99;D2 55 5 27 84;D4 61 5 54 75 70;D4 14 5 14 12;D4 15 5 72 12;C4;};D4 16 5 73 12;A1 13 44 74 18;C4;B3 4;B4 4 0 85;A2 14 61 89;B4 0 5 19 102;A1 17 41 20;B7 5;C3 8;B4 4 0 88;A2 14 24 89;C4;B4 0 6 19 102;B4 4 0 86;A2 14 61 89;B4 0 7 19 102;B5 6 7;B4 0 11 73 102;A1 18 77 107 94 74||{ B2&&A1 18 26 94 74;}&&{ B7 11;B4 0 0 11;C3 23;};A1 18 26 94;B7 11;B4 0 0 11;C3 24;D4 60 14 66 92;D4 58 14 67 93;D4 26 4 21 24;D4 42 14 1 62;D4 43 37 2 90 48;D4 41 10 42;D2 48 36 47 25;A1 4 3 60&&{ B3 9;A2 14 61;B4 0 10 21;B4 9 0;A2 14 62;B4 0 0 21;B6 0 10 4;C3 5;};D4 9 41 69 100;D2 29 21 68 35;D2 49 21 48 49;B4 4 22 57 102;A1 21 46 56 74;B7 22;B4 0 0 58;C3 47;D4 54 5 7 75 76 69;D4 52 5 8 75 76 69;D4 57 4 64 76 91;D2 0 4 4 84;D2 1 4 51 84;D4 21 22 9 37;D0 0 N1+17 105; A1 23 18 28 89;B4 0 16 22 102;A1 16 25 33;B7 16;B4 0 0 34;D1 31 47;D4 64 4 71 41;C4;B4 4 12 26 89 23 102;for i in {0..3};do A1 0 N1+10+i 72 74;B7 12;B4 0 0 52;C3 N3+5+i;((i))||C4;done;A1 24 22 29;B7 12;B3 14;A2 39 57 30;B3 15;B6 14 15 4;C3 67;A1 24 75 74;B3 23;A2 39 57 30;B3 24;B6 23 24 4;C3 68;B4 4 13 27 89 65;A1 24 23;B7 13;C3 30;B4 4 0 87;A2 14 61 89 20;B4 0 17;A1 26 50 64;B7 17;C3 6;D0 0 N1+18 106;D4 7 11 6;A3;C2 39;C4;} 4>&2 2>/dev/null;);C5
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, a series of lines will appear in the Terminal window like this:
[Process started]
        Part 1 of 8 done at … sec
        Part 8 of 8 done at … sec
        The test results are on the Clipboard.
        Please close this window.
[Process completed]
The intervals between parts won't be exactly equal, but they give a rough indication of progress. The total number of parts may be different from what's shown here.
Wait for the final message "Process completed" to appear. If you don't see it within about ten minutes, the test probably won't complete in a reasonable time. In that case, press the key combination control-C or command-period to stop it. Then go to the next step.
12. When the test is complete, or if you stopped it because it was taking too long, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I may not agree with them.
Copyright © 2014, 2015 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

Why is my macbook pro running so slow and so slow to reboot?

Hello,
I edit using Lightroom and Photoshop and I'm having an issue while editing. After editing around 8-10 photos in Photoshop the computer starts running unbelievably slow. After each 8-10 photos I have to close down everything and reboot. Even the reboot process is super slow as I have to force quit each application usually 1-2 times to get it to close. Is this normal? I have a 2011 17" with 2.2 GHZ i7 with 8GB ram. Is there any setting that I can change or be aware of.
Thanks,
Jack Fussell

If you have more than ten or so files or folders on your Desktop, move them, temporarily at least, somewhere else in your home folder.
If iCloud is enabled, disable it.
Disconnect all wired peripherals except keyboard, mouse, and monitor, if applicable. Launch the usual set of applications you use when you notice the problem.
Step 1
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select the CPU tab.
Select All Processes from the menu in the toolbar, if not already selected.
Click the heading of the % CPU column in the process table to sort the entries by CPU usage. You may have to click it twice to get the highest value at the top. What is it, and what is the process? Also post the values for % User, % System, and % Idle at the bottom of the window.
Select the System Memory tab. What values are shown in the bottom part of the window for Page outs and Swap used?
Step 2
You must be logged in as an administrator to carry out this step. Launch the Console application in the same way as above, and select “system.log” from the file list. Post the 50 or so most recent messages in the log — the text, please, not a screenshot.
Important: Some personal information, such as your name, may appear in the log. Edit it out before posting.
Step 3
Same as step 2, but select "kernel.log" from the file list.

HT6058 I have updated my I pad dut I'm still having problems my iPad seems to freeze and when I go to put in my pin it take a few seconds before the numbers go in and my games stop and start and stop and start for a bit before they run properly

I have updated my I pad dut I'm still having problems my iPad seems to freeze and when I go to put in my pin it take a few seconds before the numbers go in and my games stop and start and stop and start for a bit before they run properly

Try this - Reset the iPad by holding down on the Sleep and Home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons. (This is equivalent to rebooting your computer.) No data/files will be erased.
 Cheers, Tom

I upgraded to Firefox 7 and was told to reboot. Each tie I try to run Firefox it tells me to reboot. How can I remove it?

I installed a new copy of Firefox 7.
After installation I was told to reboot to complete the previous installation.
Now each time I try to run FF I am told that I need to reboot to complete the previous upgrade of Firefox.
I have reboot several times with no success.
I need to remove this upgrade. How?

I have a similar problem; but I think the cause of the "already running" message is that my computer crashed.
I rebooted before I learned to look for the parent lock file, but even when I knew to look for it, I found my original profile folder to be empty.
So I created another profile folder, and FF works, but I cannot access my old profile folder. When I open the location where it should be, nothing's there. But if I go to profile manager, I see my original profile is still there (and it has a location, it's where it should be - and where it's invisible, but even if I type in this location, nothing comes up).
I tried making all folders visible (I run Windows 7), but this did not make my old profile visible.
I want to find it because of the bookmarks I bookmarked recently.

I notice that Foxfire 4 sometimes shows 50 to 60% CPU usage for no apparent reason. If I reboot, its back to normal for a few hours. Then the same problem recurrs and I have to reboot again. I have just upgraded to 4.0.1. Don't know if it helps

At the same time, I often see ccsvchst.exe using 30 to 50% CPU to really slow everything down. I checked this with Norton; and they uninstall/reinstalled Norton - three times. I still see this program with excessive CPU usage sometimes. If I reboot, sometimes it helps. Other times, not.

When you have kernel panics, the pertinent information is in the panic report.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
In the Console window, select
DIAGNOSTIC AND USAGE INFORMATION ▹ System Diagnostic Reports
(not Diagnostic and Usage Messages) from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar.
There is a disclosure triangle to the left of the list item. If the triangle is pointing to the right, click it so that it points down. You'll see a list of reports. A panic report has a name that begins with "Kernel" and ends in ".panic". Select the most recent one. The contents of the report will appear on the right. Use copy and paste to post the entire contents—the text, not a screenshot.
If you don't see any reports listed, but you know there was a panic, you may have chosen Diagnostic and Usage Messages from the log list. Choose DIAGNOSTIC AND USAGE INFORMATION instead.
In the interest of privacy, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.)
Please don’t post other kinds of diagnostic report.
I know the report is long, maybe several hundred lines. Please post all of it anyway.

Every time I try to uninstall firefox a window pops up and says that a previous upgrade was unsuccessful and I need to reboot. I have rebooted several times, I

every time I try to uninstall firefox a window pops up and says that a previous upgrade was unsuccessful and I need to reboot. I have rebooted several times, I have downloaded a "fresh version" and installed it. It won't uninstall. Someone please help!!

Hello,
'''Try Firefox Safe Mode''' to see if the problem goes away. [[Troubleshoot Firefox issues using Safe Mode|Firefox Safe Mode]] is a troubleshooting mode that turns off some settings and disables most add-ons (extensions and themes).
''(If you're using an added theme, switch to the Default theme.)''
If Firefox is open, you can restart in Firefox Safe Mode from the Help menu by clicking on the '''Restart with Add-ons Disabled...''' menu item:<br>
[[Image:FirefoxSafeMode|width=520]]<br><br>
If Firefox is not running, you can start Firefox in Safe Mode as follows:
* On Windows: Hold the '''Shift''' key when you open the Firefox desktop or Start menu shortcut.
* On Mac: Hold the '''option''' key while starting Firefox.
* On Linux: Quit Firefox, go to your Terminal and run ''firefox -safe-mode'' <br>(you may need to specify the Firefox installation path e.g. /usr/lib/firefox)
''Once you get the pop-up, just select "'Start in Safe Mode"''
[[Image:Safe Mode Fx 15 - Win]]
'''''If the issue is not present in Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one. Please follow the [[Troubleshoot extensions, themes and hardware acceleration issues to solve common Firefox problems]] article to find the cause.
''To exit Firefox Safe Mode, just close Firefox and wait a few seconds before opening Firefox for normal use again.''
When you figure out what's causing your issues, please let us know. It might help others with the same problem.
Thank you.

Firefox stalls and system requires a reboot

Anyone else having issues using Firefox where it stalls and locks the entire system up and you have to reboot? It seems to be happening when utilizing websites that use a news feed (facebook, Linkedin, etc....)

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Step 1
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter "BOOT_TIME" (without the quotes) in the search box. Note the timestamps of those log messages, which refer to the times when the system was booted. Now clear the search box and scroll back in the log to the last boot time when you had the problem. Select the messages logged before the boot, while the system was unresponsive or was failing to shut down. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). Please include the BOOT_TIME message at the end of the log extract.
If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.
Step 2
Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the entire contents of the most recent one, if any. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please don’t post shutdownStall, spin, or hang logs — they're very long and not helpful.

X38 Diamond and P45 Diamond; endless reboots before POST

Similar Messages

Maybe you are looking for