X48C and DDR3 1333

Hello all,
I have a question about getting DDR3 to run-loading into WinXPsp2. I Just bought some Patriot DDR3 1333 memory 1.5v 9-9-9-24 Model# PDC32G133ELK
My computer post to bios just fine, which shows 2gb DDR3 1333, but my system hangs and freezes when loading into WinXPsp2. I have tried manually making sure the memory voltage is at 1.5v, and manually changing the timing to the RAM specs for this set of DDR3. I have also tried using the default "auto" voltage and timings and the sytstem hangs and freezes while loading WinXP every time. Any ideas or suggestions?
I'm pretty frustrated that nothing I've tried has worked so far, so any advice is welcome. Thanks in advance.

Quote from: rlb9682
I Just bought some Patriot DDR3 1333 memory 1.5v 9-9-9-24 Model# PDC32G133ELK
That looks like a real DDR3-1333
( http://www.patriotmemory.org/products/detailp.jsp?prodline=5&catid=13&prodgroupid=71&id=697&type=1 )
However, most of the Patriot DDR3-1333 are overvoltaged DDR3-1066.
Try to test their stability at 7-7-7-21 and 1.7V
good luck

Similar Messages

H67MA-E35 (b3) and DDR3 1333 mem

I have a pair of Gskill Ripjaws 1600 2x2g 1.5v and they work fine but I ordered some Gskill Sniper 1333 2x4g 1.5v on accident because I forgot what was in my comp plus the H67MA E35 (b3) states that it works with 1333 memory but it freezes my comp randomly (no less than once a day plus it corrupts files).
I reset everything and reinstalled an OS and it would still freeze my comp so I put my 1600's back in and all is fine but I was wondering before I send the 1333's back could this be bad ram or incompatibility or do I need to set something certain in the bios referring to the 1333 memory to make them work ? thanks.

Trouble is encountered when just mixing two kits of the same part number in far too many cases due to differences in batch production or different makers chips on them. Mixing two complete different part number kits is pretty much a recipe for failure.

OCZ DDR3 1333 4gbkit PC3-10666 Reaper on MSI x48c platinum

Hi to all,
i have recently bought this pc and having some problems with it.
here is the specs:
-msi x48c platinum (bios v.7.4beta previous 7.3)
-intel core 2 q9550
-2x2gb OCZ DDR3 1333 PC3-10666 Reaper
-ati radeon4850 512mb
-seagate 500gb hdd
the problem is that the mobo show me only 1067mhz for the memory instead of 1333mhz
and i have to reset the bios each time i want to turn on my pc otherwise it just wont boot up it crashes and try to boot again but with no luck.
i flashed the mobo with the 7.4 beta bios version but that didnt change a thing...
if any one has any solution that will be great.
Cheers .

Quote from: ironbird on 07-January-09, 23:26:25
hey Remus
do you have any other suggestions ?
any thing that might work is welcome
OCZ are well known for their messed up SPD settings and "factory overclocked" memory modules.
On the other hand, ELPIDA is a great chip maker:
Presuming your modules are using ELPIDA chips (OCZ is using Micron and ELPIDA chips mostly),
I don't know if you were lucky (DDR3-1333G) or not (DDR3-1066E).
Both chips can perform DDR3-1066 CAS6.
In any case, first of all you should try to set up the FSB/DRAM ratio in order to make them run at 1200-1266 MHz,
set the timings to 7-7-7-20 and the voltage to 1.75-1.80V
Take care: do not believe what OCZ states.
Any DDR3 voltage above 1.8V is very dangerous for the health of your memory modules and mainboard!
Also keep in mind: in many cases a damaged memory module comes with collateral damage (northbridge).
Obviously, OCZ is not going to pay for your damaged mainboard.
good luck

P45D3 Platinum And G.Skill 4GB Dual Kit DDR3-1333 F3-10666C FREEZE!? HELP!

Hi there!
First sorry bout my bad english!
I bought yesterday the new p45d3 platinum mainboard and g.skill 4GB Dual Kit DDR3-1333 F3-10666C memory and i have this same problem that seems to be popular. The Bios works fine, but when installing xp sp3 from cd it always freezes in 6%. Every single time. Have tried to clear cmos and run the system with minimum hw in it but every time same problem.
Just when i changed from Abit to MSI i counter this same prob than with abit while ago.
If someone could be so gentle and help me out with this, thank you so much!
yours
Antti

First of all, what is your current BIOS-Version. It should be displayed on the POST screen:
https://forum-en.msi.com/index.php?topic=113146.0
Quote
Intel core 2 quad Q9550 (2,83)
Q9550, C1 or Q9550, E0?
Quote
G.Skill 4GB Dual Kit DDR3-1333 (2 X 2048)
Remove one of the two modules, clear CMOS with main A/C power cable removed from PSU, load "Optimized Defaults" in BIOS and set the following BIOS Option:
- Spread Spectrum = Disabled
- FSB/DRAM Rato -> 1:1.6 [=DDR3-1066]
- Memory Voltage/DRAM-Voltage = ~1.57V
Then try again to install XP.

T500 and 4GB 1rx8 DDR3 1333 SO compatible?

I bought a 4GB 1rx8 DDR3 1333 SO Transcend RAM for my T500. Thought it would fit but on restart the laptop just beeps. Replaced with the old 2x1GB and worked fine..

Hi Thorsten,
Welcome to Lenovo Community!
I’m sorry to hear that you are facing the issue memory on ThinkPad T500.
The memory bus speed is not compatible with the system, as ThinkPad T500 will support maximum bus speed is 1067 MHz SO DIMM, hence I suggest you to replace the 4GB 1rx8 DDR3 1333 SO DIMM Transcend RAM to 4GB 1rx8 DDR3 1067 Mhz.
Please Click here to get the complete details of hardware.
Hope this helps!
Best regards,
Hemanth Kumar
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

MSI X48C Platinum ddr3 1600mhz problem

Hi
My PC Specs are
Intel core 2 quad Extreme Qx9770
ATI HD4870X2
Corsair 4GB DDR3-1600 Ram Kit (2 x 2GB, PC3 12800, 9-9-9-24, TW3X4G1600C9DHX)
2xWD velociraptor 300gbx2 raid0
When I raise ram frequency to 1600mhz (1:2)-ram voltage always manually to 1.79- then windows don't boot and an error messege appears about missing files.
SPD are auto and command rate to 2N(only here my pc boot).
Any idea how to fix this?

Please note what Corsair says in the datasheet for your modules:
Quote
Every part is tested in Corsair's factory at 1600MHz, but your actual results may vary depending on the overclocking margin of
your CPU and motherboard.
Your memory modules are DDR3-1333 memory modules with a permission to overclock & overvolt them to 1600 MHz @1.8V. However, without out an official guarantee that this will work in all cases.
You can try to increase the memory voltage a little more and to add a little extra voltage to the Northbridge/Memory Controller. Make sure that Spread Spectrum is disabled at all times.

DDR3-1333 vs DDR3-1600 (i72600) FOR CS5?

Hi again,
Does DDR3-1600 RAM have any significant advatage over DDR3-1333 for CS5?
Ref. INTEL i72600 / Win 7-64bit / No overclocking, or Video editing.
Thanks,
Leigh

Anything that increases RAM throughput will of course have a positive effect on any and all software applications. Photoshop CS5, especially with complex operations on very large images, can use all the RAM throughput it can get.
How much difference a particular choice will make for your system is entirely dependent on the design of the rest of the system.
It may be effective to seek out forums with others using that same system and ask for their personal experience.
-Noel

MSI P45-C51 (Problems With 4GB DDR3 1333)

Hello,
I have a problem with my motherboard P45-C51.
According to test reports, this motherboard supports 4GB DDR3 modules (1333).
msi.com/file/test_report/TR10_1836.pdf
Data specifically are:
Model: Kingston KVR1333D3N9/4G
Size: 4GB
2 DIMMs: V
4 DIMMs: V
R.S.T: OK
In the absence of stock the store, I bought a similar one:
Fury HiperX DDR 3 1333 (HX313C9F/4)
however, the motherboard does not recognize the memory (when I turn on the computer, 3 beeps sound and restarts, return to ring 3 times and then restarts and so on)
With 2 GB DDR3 1333 DIMM working properly.
I have last Bios v5.7
I found an online store the specified memory for my motherboard (Kingston KVR1333D3N9/4G) but want to be 100% sure it worked properly before buying.
Thnks.

hi,
With Fury HiperX DDR 3 1333 (HX313C9F / 4) i deleted the CMOS but I did not recognize. After much searching, I concluded that the problem could come from the distribution of the chips.
The Kingston (Fury HiperX DDR3 - 1333 - HX313C9F/4) memory have 512Mbx8 Chips (single-sided)
The G.Skill Ripjaws (F3-10666CL7D-8GBRH) memory have 256Mbx16 Chips (in two sided)
With G.Skill The mbo detect the memory and boot normally. No necesary delete CMOS.
The only problem is latency, latency detects and configures it is nine. However, changing the latency in the BIOS manually to seven working properly.
Thnks.

MSI Platinium P45 and DDR3

Hello i have a MSI Platinium P45 Motherboard and i would like to know if 4GB DDR3 -1333 is supported
or only DDR3-1066 is.
-Sheldon

It is very important to pay close attention to the marketing name and the model number when it comes to DDR2/DDR3 support.
The MSI P45 Platinum [MS-7512] does not support DDR3 memory sticks:
--> http://eu.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=1479
The MSI P45D3 Platinum [MS-7513] on the other hand does support DDR3 memory (but not DDR2).
--> http://eu.msi.com/index.php?func=proddesc&maincat_no=1&cat2_no=170&prod_no=1480
Quote
i have a MSI Platinium P45 Motherboard
In case you have the MS-7512/P45 Platinum you can forget about DDR3 support altogether as the board only has DDR2 memory slots. If you indeed have a P45D3 Platinum then you should know that (regardless of what MSI says on the product page for this board) the Intel Chipset Specifications for the P45 Chipset only mention DDR3-800 and DDR3-1066. DDR3-1333 modules are not officially supported on the P45 Chipset (according to Intel's Datasheets).

MSI H67MA-E35-B3 not supporting ddr3 1333

Hi,
I recently purchased MSI H67MA-E35-B3 and Intel Pentium G620 processor with Corsair xms3 2x2gb ram kit CMX4GX3M2A1600C9
Ram is not detected as 1333, but it defaults to 1066 in auto settings, if I manually change speed to 1333, pc wont boot and I have to clear cmos.
Enabling XMP in bios displays adjusted dram speed as 1600, but saving and rebooting speed sets back speed to 1066.
I want to run ram at default 1333 speed at least if the board cpu doesnt support 1600.
Also there is some issue with Ps/2 keyboard, its not detected by windows after shutting down pc, some reboots and plugging unplugging keyboards makes it work.

Quote
Ram is not detected as 1333, but it defaults to 1066 in auto settings
Please take a screenshot of the CPU-Z "SPD" view, upload it somewhere and include the link to the image here for comparison.
Quote
I want to run ram at default 1333 speed at least if the board cpu doesnt support 1600.
Actually, according to Intel specifications, native memory support of this processor is restricted to DDR3-1066:
http://ark.intel.com/products/53480
Quote
Memory Types DDR3-1066
No word about DDR3-1333 support.
Quote
if I manually change speed to 1333, pc wont boot and I have to clear cmos.
Enabling XMP in bios displays adjusted dram speed as 1600, but saving and rebooting speed sets back speed to 1066.
I want to run ram at default 1333 speed at least if the board cpu doesnt support 1600.
Also there is some issue with Ps/2 keyboard, its not detected by windows after shutting down pc, some reboots and plugging unplugging keyboards makes it work.
What is your current UEFI/BIOS Version?

Can I use Samsung DIMM 8GB DDR3-1333 on my Macbook Unibody?

Hi everyone,
Can somebody please help me give me the answer to these questions? I don't have the technical understanding to figure it out myself.
I have a MacBook Unibody (soon to be with Mountain Lion) with the following specification and memory.
1. I want to upgrade my RAM to Western Digital Scorpio Black 320GB, SATA II (WD3200BEKT)
2. I want to upgrade my RAM to Samsung RAM (DIMM 8GB DDR3-1333)
So my question is whether or not my Mac would support this Harddrive & RAM. They're both cheap and have good ratings, some of review mention Macs, but I wanted to be sure.
Plus, if they are any thorough support materials regarding manual migration, references to that would be much appreciated as well!
Best,
Gabriel

The ram is not the correct spec. Your MacBook requires
RAM Type: PC3-8500 DDR3 Min. RAM Speed: 1066 MHz
Using incorrect or incompatible ram is only asking for problems.
The hard drive should work fine, but let me ask this....why not really speed things up and move to a SSD? Prices are down and it's a big upgrade over hard drives.
Complete specs for your MacBook here
http://www.everymac.com/systems/apple/macbook/specs/macbook-core-2-duo-2.4-alumi num-13-late-2008-unibody-specs.html

Can I use this RAM for a 2010 MacBook Pro: Kingston 8GB (2 x 4GB) 204-Pin DDR3 SO-DIMM DDR3 1333?

I don't want to waste money or ruin my MacBook Pro?
Here are the specs:
Kingston
Model
KVR1333D3SOK2/8GR
Type
204-Pin DDR3 SO-DIMM
Tech Spec
Capacity
8GB (2 x 4GB)
Speed
DDR3 1333
Cas Latency
9
Voltage
1.5V
ECC
No
Buffered/Registered
Unbuffered
Multi-channel Kit
Dual Channel Kit

No you can not use it. Your mac uses DDR3 1066, not 1333. You need this type of ram:
204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM

MSI X48C Platinum and DDR3 corsair 2x4 GB @ 1600mhz WILL IT WORK??

Hi , I truly appreciate the mere existence of this forum .
my system is :
PSU : Corsair 650HX
CPU : Intel Core2Duo E6750
GPU : Geforce GTX 260
RAM : (currently 2x1gig DDR2 @ 667 Mhz)
and
i just bought 2x4gb dims of DDR3 ram (corsair vengeance)
it doesn't work ( i believe it's because it maxes out at 8 gigs so it won't support 4gig dims?? just a guess)
my question is this :
if i change the memory for four 2gig dims , at the same frequency (1600 mhz , ddr3 ) will it work without the need for tweaking ,
or at least a minimal quantity of the whole tweaking-ness?
i'm only asking because time is of the essense ( i really need the pc working )
and if there is no chance of this combination working, would 4x2 gigs at 1333 Mhz work ??
also , since i don't believe i have ever updated the mobo's bios , should i do that? ( and which is the safest way to do it??)
and just out of curiosity , what is the fastest memory that this mobo can support at 8 gigs without any stability problems whatsoever ??

Your board and the chipset do support DDR3-1600. The memory you are mentioning is not on the support list.
The board's support states Quote
Supports four unbuffered DIMM of 1.5 Volt DDR3 800/1066/1333/1600 DRAM, 8GB Max
Thus you need 2GB modules to get to 8GB if that is what you need/want.
See here for the supported memory modules http://eu.msi.com/file/test_report/TR10_1393.pdf
You will see that no DDR-1600 2gb module is even on that list. Only 1GB 1600 modules were tested.
If you want to use 2GB modules then get yourself 1333 modules. The performance difference is minimal and you should have good stability with these modules.

X48C and Q9550 SLB8V

SPEC
X48C PLATINUM UPDATED TO 7.2 BIOS
INTEL Q9550 SLB8V
KINGSTON 4 GO KIT DDR3 1333MHZ
COOLERMASTER 850W
SAPPHIRE RAD 4870 1GIG 8.11 CATALYST
LG 22X DVDRW SATA
SEAGATE 500GIG SATA 32MEG CACHE
VISTA 64 HOME BASIC
I did install windows whitout any problem.
When I began to install drivers, I had some blue screen with fltmgr.sys and had to reboot. (internmitant crashing)
Who can help me for my problem ?
Is it the bios version for cpu rev., imcompatibility somewhere ?
Sorry for my bad english

Quote from: mertch on 24-November-08, 03:36:17
re-seat ok works fine now
Thanks
If you have stability troubles, switch to Command Rate to 2T {2N in BIOS} and re-test.

T500 DDR3 1333 - Will This Work?

Hi,
I've got a quick and hopfully simply question.
According to this: http://support.lenovo.com/en_US/detail.page?LegacyDocID=MIGR-55644#t
My T500 can support PC3-8500 DDR3-1066 SODIMM. However, the availablity of 1066 DDR3 where I live is virtually non existent, while I can easily purchase a 1333 DDR3. Will it simply work at the lower frequency, or can I expect problems?
Thanks a lot!
Solved!
Go to Solution.

Crucial's and Kingston's memory finders show both 1066 and 1333 RAM as compatible with the T500. You should be OK if you stick with a reputable supplier. Avoid value RAM.
Crucial Memory Advisor results for the Lenovo ThinkPad T500 Series Laptop/Notebook.
I'm running Crucial (1066) in my T400. There are reports of compatibility problems with our vintage ThinkPads and Corsair RAM. YMMV.
[edit] This KB may be helpful: Upgrading RAM on Lenovo ThinkPad T500
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

X48C and DDR3 1333

Similar Messages

Maybe you are looking for