X48C Strange efficiency issue with FAN

Hello,
I have a strange issue in Hardware Monitor Efficiency in BIOS.
When I connect a Fan (12 cm with 4 led) to Motherboard SYSFAN2 (or other SYSFAN) efficiency of the system drops to 40%, but when I remove the FAN efficiency goes up to 90%. When I connect this fan directly to the PSU with a molex, efficiency is maintained to 90%.
I have connected other 12 cm FAN to SYSFAN but do not cause this problem.
Can someone help me?
Fan information:
Scythe Kaze-White 120 mm
4xWhite LED
800 rpm (19.02dBA/31.27CFM) - 1600 rpm(27.92dBA/66.10CFM)
Cable 30 cm

"But I've ran a P4 2.8 computer with that PSU for over a year without any issues at all."
That doesn't prove anything. Don't trust to cheap PSU's.
Also for your current build its too weak:
HEC-350LD-T. AC Input: 115/230V~, 50~60Hz, 8/5A, Fuse Rating: T8AL, 250V~.
DC Output: +3.3V~20A, +5V~33, +12V~15A. +5Vsb~2A, -5V~1A, -12V~1A. MAX OUTPUT POWER: 350W. +5V&3.3V Combined 180W.
Get a single rail PSU with high amperes on +12V +30A or above.
Add-on to read:
>>> PSU's---2 x 12v---The Dual Rail Myth <<<
>>> Is your problem caused by your PSU? <<<
Good PSU suggestions:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
"with that PSU for over a year"
One more reason to be suspicion.

Similar Messages

Issue with fan or heat in macbook pro

Issue with fan or heat in macbook pro

arsal ahmed wrote:
Issue with fan or heat in macbook pro
What's the issue?

Strange Printing Issue With New HP & Pages

Hello!
I have a very strange printing issue with a new HP printer. I have written pages documents heavy in Texts which are located within tables. The documents print fine on a Cannon and Epson printer and look great but when I print the document on my new HP Laserjet Pro 400 Colour M451nw some of the text on some rows come out of the printer looking like they are bold / slightly fuzzy. This only happens with some of the rows of text, not all of them. The font is the same in every row with the same format.
You can see this in the attached image. The first line (Thanks very much) has printed correctly but the subsequent lines look bold / slightly fuzzy.
After a lot of testing the only way I can resolve this is if I copy the content into a new pages document and only then it will print and look ok with the HP printer.
This must be a problem within my origional document. I would simply copy and paste everything into a new document however this would take a very, very long time (over 5 years of work producing teaching materials and over 100 documents and thousands of tables and formatting that cannot be copied and pasted).
Also, on other printers you can see the lines seperating each row of the table. These lines are not visible on the HP print outs, even when the table is copied into a new document.
Has anyone come accross an issue like this before? Is there a way I can fix this without creating a new document? Do I need to get a new another new printer (the 4th printer this week!)?
Any advise, wise words would be greatly apprechiated!
Thanks!

Sorry, Fruhulda. After 4 hours on the phone with Apple care they are taking this issue further themselves. It seems to be a problem with our pages document and the compatibility with certain drivers. We have still not gotton to the bottom of it and Apple are going to get back to me when they have an answer.
We also worked out that the issue only happens when you print via Ethrenet & USB. Printing via Wifi is ok and there are no quality issues.
Very Strange!

Strange performance issue with 3510/3511 SAM-FS disk cache

Hi there!
I'm running a small SAM-QFS environment and have some strange performance issue on the disk storage part, which somebody here might be able to explain.
Configuration: one 3510, dual controller, RAID-5 9+1, one hot spare and one disk not configured for whatever reason. The R5 logical drive hosts a 150GB LUN for SAM-QFS metadata (mm in SAM-FS speak) and a 1TB LUN for data (mr in SAM-FS speak). Further, there are two small LUNs (2GB, 100GB) for some other purpose. Those two LUNs have nearly no I/O. All disks are SUN146G. Host connection is 2GBit, multipathing enabled and working.
Then the disk cache became too small, and the customer added a 3511 expansion unit with SUN300G disks. One logical drive is a RAID-1, 1+1, used for NetBackup catalog. The other is a RAID-5, 8+1, providing two LUNs: 260GB SAM-FS metadata (mm) and 1.999TB SAM-FS data (mr).
For SAM-FS, the LUNs form two file systems: one "residing" in the 3510, the other "residing" in the 3511 expansion. Cabling is according to the manual and checked several times by several independant people. Operating system is Solaris 10, hardware is a V880.
The problem we observe: SAM-FS I/O on LUNs on disks inside the 3510 is fine. With iostat, I see 100MB/s read and 50MB/s write at the same time. On the SAM-FS file system which is running on the two LUNs in the 3511, the limit seems to be at 40MB/s read/write. Both SAM-FS file systems are configured the same in regards of block size.
In case I have activity on both SAM-FS file systems, I see 100MB/s+ on the LUN running inside the controller shelf and another 40MB/s on the disk runnin in the 3511 expansion chassis. So, the controller is easily capable of handling 150MB/s.
Cache settings in the 3510 controller are default I think (wasn't installed by me), batteries are fine.
Is this 40MB/s we experience a limitation by the expansion shelf? Don't think so. Anybody has any ideas on this? What parameters to check or to change? Any hint appreciated. I can also provide further details if needed. Thank you.
wolfgang

SUN300G disks sound like 300GB FC disks.
Depending on how many files are in the SAMFS file system, sharing the mm and mr devices on the same RAID array can be a pretty horrible idea. In my opinion and experience, it's almost always better to NEVER put more than one LUN on a RAID array. Period. Putting more than one LUN on an array results in IO contention on that array. And large, unnaturally configured (9+1? Why?) RAID arrays will have problems from the start.
What are the block sizes used on the RAID arrays? It wouldn't surprise me to see that the RAID array on the expansion tray has a very large block size. Larger block sizes are, in general, not better. Especially for SAMFS metadata - which IIRC is something like 8k or 16k blocks.
I suspect what is happening is most of the metadata updates are going to the mm device on the new array, contending with the IO operations on the file data.
How much space is left on each mm device? What does "iostat -sndxz 2" show when you're having the IO problems?

Strange sound issue with my Satelite U300

I've got a strange sound problem with my laptop.
I have XP pro + SP3 (downgraded from Vista to XP)
Couple week ago, a reinstall XP, because I thought it could solve my problem. But...nothing.
This is a problem: When I turning my laptop on, it gives me a message, "warning, cannot access volume control". When I check device manager, the only yellow question mark is bout PCI memory controller and there is no more unrecognized devices founded.
In Sound, video and game controller - Realtek High definition Audio is just missing.
Usually , then everything is ok, in "Device manager - Sound, video and game controller " I have - Audio Codecs, Legacy Audio drivers, Legacy Video CApture Devices, Media Control Devices,
Video codecs, Realtek High definition Audio. But then sound is missing, the "Realtek High definition Audio" is also missing.
Computers restart doesn't help. Even, when I uninstall Realtek sound drivers from "Add and remove.." and install it freshly, it also doesn't help. I tried to update drivers - nothing..
But, there is one strange thing: When a turning my laptop on couples hours later, or even next day (for exmpl) everything is ok. Sound works. And I can understand why....
All drivers downloaded from Toshiba. BIOS is being updated.
Maybe somebody know how to solve this problem? Any solutions?

Hello
This issue has been brought up on this forum several times under other topic headings. Look under Audio Driver Missing, for instance. I have had this exact problem since purchasing my Toshiba notebook more than a year ago. Toshiba tech support is useless - and you're right that BIOS updates or changes make no difference, at least so far. The other ideas or replies given so far on this forum also don't solve the problem. Unfortunately for now I think you have to live with it, until someone spends the time to figure out what is really going on. I am curious if it is a Toshiba problem, a Realtek problem, or a Vista / compatibility issue.
I have two suggestions, which aren't fixes, but can help get your sound back when it disappears:
1. Restart several times, not just once. Sometimes it works.
2. Try the System Restore function. This used to work for me, until I updated the BIOS and now it no longer helps with this issue!
Make sure you post a solution if you figure it out!

Strange Networking Issue with OES

Since moving our entire infrastructure from Netware to OES, I've been trying to figure out a very strange issue. We are a K-12 school system with a data center at the central offices and a single server at each school. The data center has the servers that run all the centralized stuff, including the Master replicas for [root], the DA's for SLP, etc. We noticed that sometimes a school's server will drop out of the SLP tables. When that happens, we also cannot SSH to the school's server from the central servers. We can SSH to it from any other machine on the same subnet as the central servers. The central servers can ping it, but no UDP/TCP traffic can pass between them (no web traffic, etc). We finally realized it only happens when the ISP that serves that school has a brief blip or outage of some sort. The only way we have found to get the servers talking again is to reboot the central servers.
We have tried:
Restarting almost all services on central servers
Stopping and restarting networking
Switching to runlevel 1 and then back
Stopping firewall and/or shutting it off completely
Checking hosts.deny files
Disabling virus scanner (McAfee Enterprise)
Changing vmware network drivers from E1000 (known issue with vSphere 5.1) to VMXNET3
All servers run on HP Proliant servers (blades at central office, towers at schools) running vSphere 5.1. Links between the central office and schools are all 100Mbps fiber via two different ISP (depending on the school's location). A restart of the central office server fixes it every time. I am out of ideas now and at a loss as to why this happens when a WAN link goes down. We thought it was just isolated to one ISP, but it was just that that particular ISP is not quite as reliable as the other. We had an extended power outage at a school served by another ISP over the weekend and saw the same issue with that server after power was restored.
Any ideas or suggestions at where else we should be looking? We also run ZCM 11 at each school and the central office. When this happens, those servers never lose connectivity with each other and with the OES servers on each end. The ZCM servers run on the same vSphere host as the OES servers.

On 04/08/2014 12:26 PM, jmlester wrote:
>
> Since moving our entire infrastructure from Netware to OES, I've been
> trying to figure out a very strange issue. We are a K-12 school system
> with a data center at the central offices and a single server at each
> school. The data center has the servers that run all the centralized
> stuff, including the Master replicas for [root], the DA's for SLP, etc.
> We noticed that sometimes a school's server will drop out of the SLP
> tables. When that happens, we also cannot SSH to the school's server
To be clear, while i think this correlation is possible, I do not see any
possibility of causality in here unless your SSH client is somehow using
SLP to resolve the SSH server, which seems very unlikely. I'm not sure if
you're trying to state that SLP is the cause of the SSH stuff, but I do
not think you are.
> from the central servers. We can SSH to it from any other machine on
> the same subnet as the central servers. The central servers can ping
> it, but no UDP/TCP traffic can pass between them (no web traffic, etc).
Hmmm........... so routing works, and the server is even responding to
requests made to it (presumably, or something else is), but SSH is not
responding, or something is preventing it from responding.
> We finally realized it only happens when the ISP that serves that school
> has a brief blip or outage of some sort. The only way we have found to
> get the servers talking again is to reboot the central servers.
>
> We have tried:
>
> - Restarting almost all services on central servers
> - Stopping and restarting networking
> - Switching to runlevel 1 and then back
> - Stopping firewall and/or shutting it off completely
> - Checking hosts.deny files
> - Disabling virus scanner (McAfee Enterprise)
> - Changing vmware network drivers from E1000 (known issue with vSphere
> 5.1) to VMXNET3
>
>
> All servers run on HP Proliant servers (blades at central office, towers
> at schools) running vSphere 5.1. Links between the central office and
> schools are all 100Mbps fiber via two different ISP (depending on the
> school's location). A restart of the central office server fixes it
> every time. I am out of ideas now and at a loss as to why this happens
> when a WAN link goes down. We thought it was just isolated to one ISP,
> but it was just that that particular ISP is not quite as reliable as the
> other. We had an extended power outage at a school served by another
> ISP over the weekend and saw the same issue with that server after power
> was restored.
>
> Any ideas or suggestions at where else we should be looking? We also
> run ZCM 11 at each school and the central office. When this happens,
> those servers never lose connectivity with each other and with the OES
> servers on each end. The ZCM servers run on the same vSphere host as
> the OES servers.
I'd get a LAN trace from both sides at the same time. At the very least,
run tcpdump as shown below on both the central office machine as well as
the remote machine to see how the packets differ when trying different
things. If you do a test and do not see output on both sides, do it again
writing it to a file and post somewhere for us to review. Note: since
it's an SSH problem I would either NOT SSH into the system, or I'd be sure
to limit the tcpdump capture/output to something specific to the
connection being tested. Tracing something over which you are sending the
tracing data is never fun since every packet picked up causes another
packet to be generated, to be picked up, to be generated.... ad infinitum.
To see tcpdump output with limited details on the screen:
Code:
sudo /usr/sbin/tcpdump -n -s 0 -i any -vv
To write tcpdump output to a file:
Code:
sudo /usr/sbin/tcpdump -n -s 0 -i any -w /tmp/problem-20140408.cap
While filtering when capturing is typically not desired, you can do it by
adding something like 'host 10.1.2.3' to the list of tcpdump parameters at
the end of either of those two commands. The reason filtering during
capturing is not desired is that you may miss something.... the SLP
traffic, DNS, ARP, ICMP error showing the exact problem, etc.
Good luck.
If you find this post helpful and are logged into the web interface,
show your appreciation and click on the star below...

Very Strange Network Issue With Two Guests on 2012 R2 Hyper-V Failover Cluster

Hi all. We're having a odd issue with two guests on our 2012 R2 failover cluster.
In a nutshell, if we shutdown a particular server (I'll call it Server A) another totally different server (Server B) on the same node loses it's network connectivity to the domain. If we start server A back up, network connectivity returns on server B.
At first I thought server A might be running a service that was somehow linked to server B, so I decided to disable server A's NIC. Interestingly, that had no affect on server B's connectivity.
The next step I tried was pausing server A and again, no adverse affect on server B's connectivity.
Next step was to live migrate server A to another node. This action did
cause server B to lose its network connection.
One other clue is that if I ping server B from either of the Hyper-V hosts in the cluster, I never lose network connection to server B.
So I would suspect this is some network issue on the cluster, but I'm kind of at a loss where to go from here.
Has anyone seen this behavior before or does anyone have any troubleshooting suggestions I can try?
Thanks!
George Moore

Hi Sir,
I'v never seen this before .
>>Next step was to live migrate server A to another node. This action did
cause server B to lose its network connection.
They are connecting to same virtual switch ?
First please run cluster validation to check if there is any error .
If it is ok , please try the following items for troubleshooting :
1. shutdown serverA serverB
2. then add another virtual NIC for serverB
3. start server B check if the issue happens to both "old" and "new" virtual NIC .
In addition , you can live migrate both A and B to another node , then try to live migrate A to the original node .
If the issue persists , I would suggest you to remove that virtual switch on both nodes then re-create them .
Best Regards,
Elton Ji
If it is not the answer please unmark it to continue
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

MSI K9AGM4-L - Strange freezing issue with games

I built this low budget computer for my friend, and it has a strange bug. The parts are:
MSI K9AGM4-L motherboard
X2 64 4600+ AM2 processor + stock cooler
2 x 1gb Kingston 667 DDR2
PNY 7600GT PCI-E
Antec Solo Quiet case + 12cm fan
HEC 350W power
Tested with WinXP SP2 and Vista 64Bit
Bug: Everything works ok, but everytime I start a game (IL-2 1946 for example) it freezes continuosly.
OK, I thought it was a temp issue, but...
- I've played IL-2 1946 for over 200 hours with that card, when it was on my own computer and it never had any issues. I have the exact same Antec case on my own computer, with one 12cm fan.
- That power doesn't feel hot at all after it has been on for over an hour or so.
- Processor temp never exceeds 47-49C when playing, so can't be it either.
- SATA harddrive temp is 47C according to "Everest".
The only thing that seems hot to touch is the NB heatsink (which is very small on this mobo, btw). So I made this test: I used an open case and put this huge 40cm fan next to it and played the game. It still started to freeze even though the heatsink wasn't very hot.
I also thought it's something with the drivers/software, so I tested everything with Vista 64bit + different drivers/software, didn't help. Also I tested one ATI card, same symptoms.
I also checked that the NB heatsink is properly seated.
SO.... any ideas what can cause this? Is it the NB afterall, that needs a better heatsink...or?
Any help to solve this will be welcomed, thanks in advance.

"But I've ran a P4 2.8 computer with that PSU for over a year without any issues at all."
That doesn't prove anything. Don't trust to cheap PSU's.
Also for your current build its too weak:
HEC-350LD-T. AC Input: 115/230V~, 50~60Hz, 8/5A, Fuse Rating: T8AL, 250V~.
DC Output: +3.3V~20A, +5V~33, +12V~15A. +5Vsb~2A, -5V~1A, -12V~1A. MAX OUTPUT POWER: 350W. +5V&3.3V Combined 180W.
Get a single rail PSU with high amperes on +12V +30A or above.
Add-on to read:
>>> PSU's---2 x 12v---The Dual Rail Myth <<<
>>> Is your problem caused by your PSU? <<<
Good PSU suggestions:
https://forum-en.msi.com/index.php?topic=112039.msg836246#msg836246
"with that PSU for over a year"
One more reason to be suspicion.

Strange keyboard issues with my 2012 Macbook Air...

Hey guys,
I've been using my brand new macbook air for the last 2 weeks or so without any issues. Today I took my laptop out of my bag after work and noticed that things on the keyboard have been really weird. For starters, certain keys on the right side of the board are not giving me the correct symbols when I press them. There are a few other random keys (mostly the numbers and symbols) that are incorrect.
ie: I press shift+2 for the @ but I get ' instead or I press ] and get @ instead.
Another weird thing to note: Caps lock turned on = lower case letters and Caps lock turned off = upper case letters.
I left my laptop alone for a few hours and when I came back to it later, whenever I turn it on it automatically boots into safe mode which makes me assume that the shift key is stuck in some weird way.
What can be causing this?

I have about the exact same problem, my macbook air 13 in (bought january this year in Belgium) is having the same issues, first (i'm on an azerty keyboard - first the following keys stopped working ; . : / and a week a half after that almost the whole keyboard gave up, symptoms
lowercase c reacts like the enter key
lowercase v types ^V
the whole row of keys from a tot Z don't work or produce garabage like ´^VVVVV1111111111
numerical keys work, but using shift together does not
If I attach an external keyboard, then the same key mismappings or whatever happening here, are also on the external keyboard, so I can't even login with an external keyboard
Sounds like hardware failure, but no idea why, my macbook is in top condition, no spills, no high humidty, really nothing whatsoever
If any one would have a clue prior to bringing it to mac store?
All defaults already done (smc - pram reset), reboot to recovery terminal there same problem with internal and external keyboard, boot from usb etc etc
For me really really really dissappointing, bought the top model macbook air with all upgrades available, as a stable working laptop for business use (for which I payed premium for a premium device) , but stuff like this happens on cheap windows consumer laptops, not on a macbook air
I have about everything over here, 2 Iphones, 3 Ipad's, an Imac, a MacPro, a Macbook Pro, each and every one of the durable and decent devices but this macbook air has been nothing to be excited about untill now, lots of blowing fans all the time, run's quite hot, the touchpad having it's on will
Always been a very loyal Apple customer as the list of Mac devices above shows, but things like this make me reconsider
Best Regards
Nico

10.1.3 Production - Strange migration issues with OC4J

Hi,
first of all my congrats on another great release of my favorite Java IDE. Bad thing is I can't enjoy it as much as I want currently because of the following issue:
I'm working on a large project based on Struts, Tiles and Spring. The thing was born under 9.0.3 and happily survived several migrations since. It is running perfectly in 10.1.3 EA (OC4J and Tomcat 5.5). So I didn't expect any issues when switching to the production release. As I expected, everything worked without any errors. Fine. But then, when expectingly starting it in OC4J, things suddenly looked a bit different, for the login page came up somewhat naked. In fact, that is no wonder, as the app didn't find its CSS files, images, whatever. I import those resources (JSP 2.0) via the follówing line:
${pageContext.request.contextPath}/path_to_css.css
As it turned out, the pageContext thing wasn't resolved and so contextPath stays blank. Furthermore, the JSPs generated can't get access to session objects via expression language (eg. ${myBean.myAttribute}. JSTL <fmt:>, on the other hand, works wonderfully. Now for the odd part: if I change the JSP while the app is running and
then hit 'reload' to get it recompiled, the problem is gone. Looking at the .jsps sources, JDev generates something quite different from what OC4J does (the latter is the working version). I've spend the whole day now trying to find out why, including two fresh installs and setting up a test project, for I expected Tiles to be the culprit, but it's not; in fact, the issue also happens with a no-frills JSP page. Now I'm rather at the end of my knowledge. Has anyone had similar problems or knows how to resolve this issue? Any hint would be deeply appreciated :-)
-- Chris.
NB. My version is 10.1.3 J2EE (not Studio); I tried both the base one and later the complete version which comes with its own JDK.

Alas, talking to myself is fun, so I'll proceed. Today, I set up another simple test project (Servlets 2.4/JSP 2.0) with a JSP that just issues the following:
Context path: ${pageContext.request.contextPath}
Upon comparing what gets generated, I noticed the following differences:
1. What JDev generates and what does not work correctly:
javax.servlet.jsp.el.VariableResolver __ojsp_varRes = (VariableResolver)new OracleVariableResolverImpl(pageContext);
try {
out.write(__oracle_jsp_text[0]);
out.write(__oracle_jsp_text[1]);
catch( Throwable e) { .. }
2. The same fragment recompiled in OC4J:
javax.servlet.jsp.el.VariableResolver __ojsp_varRes = (VariableResolver)new OracleVariableResolverImpl(pageContext);
com.evermind.server.http.JspCommonExtraWriter __ojsp_s_out = (com.evermind.server.http.JspCommonExtraWriter) out;
try {
__ojsp_s_out.write(__oracle_jsp_text[0]);
out.write( (java.lang.String)oracle.jsp.runtime.OracleJspRuntime.evaluate("${pageContext.request.contextPath}",java.lang.String.class, __ojsp_varRes, null));
__ojsp_s_out.write(__oracle_jsp_text[1]);
catch( Throwable e) { .. }
As you can see, only the latter version contains code to evaluate the EL expression (the italic parts) at all! How on earth does this come from? Is there any switch in JDev to explicitly tell it to generate 2.0-compliant, EL-aware stuff apart from specifying 2.4 in the wizard?
-- Chris.

Strange axbridge issue with Visual Basic

I started having a very strange problem with my axbridge wrapped bean around the time I switched to JDK 1.5. Problem is, I can't seem to get rid of it by rolling back to earlier versions.
Here's what happens: I create a very simple non-visual bean:
package pack;
public class Bean1 {
public Bean1()
System.out.println("Constructor");
public boolean someMethod ()
System.out.println("1");
return false;
I then create Bean1.dll using the packager.exe provided with the JDK, and register it as part of the packaging process.
Then, I go into Visual Basic 6 and enter this code:
Private Sub Command1_Click()
Dim xx As Object
xx = CreateObject("Bean1.Bean.1")
End Sub
On the CreateObject call, Visual Basic gives me the error "Object variable or With block variable not set", which isn't helpful.
In the Java console with level 5 tracing turned on, I see this:
basic: Referencing classloader: sun.plugin.ClassLoaderInfo@17ba38f, refcount=1
basic: Registered modality listener
basic: Added progress listener: sun.plugin.util.GrayBoxPainter@9ffe3f
basic: Loading applet ...
basic: Initializing applet ...
basic: Starting applet ...
basic: Stopping applet ...
basic: Removed progress listener: sun.plugin.util.GrayBoxPainter@9ffe3f
basic: Finding information ...
basic: Releasing classloader: sun.plugin.ClassLoaderInfo@17ba38f, refcount=0
basic: Caching classloader: sun.plugin.ClassLoaderInfo@17ba38f
basic: Current classloader cache size: 1
basic: Done ...
basic: Joining applet thread ...
basic: Destroying applet ...
basic: Disposing applet ...
basic: Quiting applet ...
java.lang.NullPointerException
     at sun.plugin.AppletViewer.loadJarFiles(Unknown Source)
     at sun.applet.AppletPanel.runLoader(Unknown Source)
     at sun.applet.AppletPanel.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
basic: Exception: java.lang.NullPointerException
java.lang.NullPointerException
     at sun.plugin.AppletViewer.loadJarFiles(Unknown Source)
     at sun.applet.AppletPanel.runLoader(Unknown Source)
     at sun.applet.AppletPanel.run(Unknown Source)
     at java.lang.Thread.run(Unknown Source)
basic: Modality pushed
basic: Joined applet thread ...
basic: Unregistered modality listener
The only thing I've found in the bug database that seems even remotely related to this is bug 6391104, which is related to plugins somehow.
I do not understand why applets are involved in this at all.
When I try to instantiate the COM object from a C++ program, everything works fine. My problem only seems to occur with Visual Basic (version 6, not .NET).
This problem seems so fundamental that it seems impossible that no one else has run into it, but there 's nothing about it on any forum or buglist that I've seen. So, I figured there must be something very obscure wrong with my setup. However, I tried installing this on a brand new machine using my trivial case, and I still have the problem. I'm really at my wits' end. Anyone have any ideas?

You definately want to go to CR 2008. I'd recommed that you call 866-681-3435 and ask about the possibility of getting a 30 day eval.
Ludek
Follow us on Twitter http://twitter.com/SAPCRNetSup
Got Enhancement ideas? Try the [SAP Idea Place|https://ideas.sap.com/community/products_and_solutions/crystalreports]

Strange Import Issue with Canon 7D Footage Final Cut Pro X

I'm hoping some folks can help me here as I'm stumped.
I shot around 60 minutes of last evening with my Canon 7D. File sizes ranged from 500MB to 4GB. I imported from my 8GB memory card a 3.6 GB file and a 500MB file with no issue. I then moved on to my 16GB memory card, which was full with around 7 clips, and started importing. I noticed the import was going slow but I was also importing some audio from SD cards on the same card reader, which I've always done in the past, and figured it was just a USB 2.0 bandwidth thing.
I then got an error regarding the Import Failing (see attachment) but the file appeared to have imported without issue. Upon further inspection during the import however, I noticed any file larger than 1GB was showing as the PAL codec (after it imports it correctly shows H.264 but more on that later). I checked the 3.6GB file from my first import and it did not share this issue. While on the shoot I had backed up a number of these files to my iPad so I attempted to import them from there and althought he PAL codec was not listed, I did get the Import Failed error. I also tried a brand new card reader and a different Event/Destination the issue remained.
I've restarted, repaired permissions, and the issue remains. I have never encountered this error and imported a similar amount of footage and clip sizes two weeks ago. I'm stumped, has anyone else seen this?

I did some experiments this morning, and Richard's method worked. Thank you!
However, I didn't follow Richard's steps 2 & 3. When importing, I let FCP copy the files to the FC Events folder. It still worked. In step 1, I did not copy the .THM files to the new folder on my HD.
I did a second experiment that did not work:
1) Copy .mov files (only) from CF card to new folder on HD.---no .THM files
2) "Create Camera Archive" with FCP - Store new archive in its own folder on my HD
3) Tried importing from the new Camera Archive - This crashed just like before.
This tells me FCP is OK with importing individual media files to a FC Event. It seems to crash when it thinks there's a camera involved.
Later today I'll try to import some AVCHD files and see if it crashes on import. For AVCHD footage, you need to rely on FCP's "Import from device" capability. Those files need to be transcoded to be usable at all.
More later.
Marshall

Strange sorting issues with podcasts?

I subscribe to the Onion News Network podcasts, the audio only versions, and no matter what information I change I cannot get my podcasts to sort together. iTunes keeps them together in the finder, but the app separates them. I've had two separate icons for the past few years, and now there is a third! Please see the image below and help if you can. The second view only shows 3 podcasts, as seen below.
P.S. The new icons randomly show up when the podcasts are refreshed. Is it something on Onion's end? If so, why is nobody else asking about this!

Hi Vetsrini,
I have implemented the above mentioned code in my logic. But it works fine only when the nodes in the XML has the data. In case if the XML has null value in one fund, It is not sorted according to the latest records. Can u please provide an alternative how to sort the data using date? I have read in ur previous posts that the date needs to be converted into Canonical Format inorder to sort according to date. Can u please send me the syntax how to convert a date into Canonical Format? Right now the format of the date in my XML is in MM/DD/YYYY format. Please help me. I am struck up with this only issue which is causing me a trouble since 1 week.
Thanks & Regards,
Pradeep Reddy Kypa
8801908980

Strange connectivity issue with WRT54G

I hope you can help with this. I have just moved into a new house and am trying to connect the internet through their WRT54G wirelessG router. It shows up with full reception in the WindowsXP wireless connection manager, but it will not connect. IPCONFIG has its status as 'Media Disconnected', and all pings to 192.168.1.1 fail. A loopback test ping to 127.0.0.1 works. My flatmate's wireless connection to same router works fine, and when he accesses the router's configuration page it states that I HAVE connected and DHCP has assigned me an IP. I've tried everything; deleting & resetting the connection, resetting the TCP/IP/Winsock protocols, disabling the WEP security on the router, but no luck. The connection is fine on my flatmate's computer. My machine is a Dell laptop and and I have taken it to 3 other wireless networks and it connects to them no problem. I can connect to the router in question fine wired with a CAT5 cable but it's not convenient to have that as a permanent solution (when the router is supposed to be wireless!)
I work in IT and thought I was pretty good with computers but this has me completely stumped! I looked for new firmware but couldn't find any listed on your site - if there is could you provide a link, or if you've any other ideas what could be causing this please let me know!
Thanks
Message Edited by steviemac on 08-15-2007 09:07 AM

Sounds to me like it's related to a configuration setting despite the "Media Disconnected" message. Try disabling any SpeedBooster or other non-essential options on the router. Perpaps the Dell WiFi NIC doesn't like it. I doubt it's a MAC filtering issue but you can try removing that too. If it's a somewhat older laptop you can try removing the small panel on the bottom and reseating the WiFi adapter if it's located there. Newer Dells have them built in around the LCD where you can't access them.

Strange security issue with reports in Web Analysis.

Hi All,
I am working on Hyperion System 9.3.1 and Reports are developed using Web Analysis. To develop the reports I followed the following sequence.
1) Developed the reports with admin rights on Web Analysis reports and Essbase cube.
2) Create a group with users in Shared services and assign the following roles Analyst, Data Editor,Data Source Publisher,Dynamic viewer,Explorer,Viewer rights in Hyperion System 9 BI+ level and calc access for the database at Analytic Server level.
3) Create a separate folder in Web Analysis studio and copy the WA reports there(say- reports).
4) At workspace level, I gave the access on folder and on report.
Now when I login as one of the member of the group I am unable to see the reports in the folder.
I can see the reports when I login as an admin.
Am I misssing anything or the security I gave is insufficient.
Waiting for your reply.

can you tell me what inherit permission you gave to make it work.
I have a folder having a view access only. whenever i make new reports as admin...i cant see my new reports untill i refresh the "apply permission to children" options gain.
But thats not what i m looking for...i want it come on its own when I create a report.

X48C Strange efficiency issue with FAN

Similar Messages

Maybe you are looking for