X79-GD65 (8D) and i7 3820 issues

Hello members
I recently purchased a MSI X79-GD65 (8D) motherboard and an Intel i7 3820 CPU.
I have installed 4 sticks of 16GB memory.
When I turn the computer on, everything looks normal on the motherboard, except I get no video (have tried two video cards).
The CPU phase LED shows 3 bars, no digits on the debug motherboard LCD.
I have noticed that it is impossible to turn the power off and the PSU needs to be switched off.
From what I am reading it seems I have an old BIOS, (the chip has a red dot) and this is incompatible with the 3820.
I was wondering if anybody knows a workaround to allow me to get into BIOS to reflash the chip.
The fact that the BIOS chips are surface soldered doesn't help either.
Any ideas appreciated.

it is dead to me.
there are some serious key flaws with MSI.
Why is the BIOS chip soldered surface mount, if BIOS are always outdated, why not install a socket BIOS chip, this would then be a very straight forward fix
Why do I need a CPU installed to flash my BIOS, ASUS has this feature on their motherboard, this could easily be fixed in this case
The RMA website for Australia is non functional, try navigating http://au.msi.com/service/wheretobuy/ you get a JavaScript error.
I reread the manual which points to the url http://www.msi.com/service/cpu-support (which doesn't even work because of the missing trailing forward slash) and it pointed to the url http://www.msi.com/product/mb/X79A-GD65--8D-.html#/?div=CPUSupport.
Nothing on that page even hints there may be incompatibility issues.
Not a good experience

Similar Messages

MSI Z87 GD65 Gaming and msata speed issue...

Hi,
So I'm running the MSI Z87 GD65 Gaming with a 128GB SanDisk msata. Now it all works perfectly; no BSOD or crashes, but what I have noticed is that sometimes when the PC boots and I look in Intel Rapid Storage Technology, the msata on port 5 is running at 3Gb/s not 6Gb/s: I verified the speed loss using AS SSD benchmark. Reboot and it's back to 6Gb/s and back to full speed.
Anyone else seen this or have an idea of a solution?
Thanks

Quote from: JLio01 on 06-March-15, 14:21:58
How often can you notice the problem? You mentioned AS SSD Benchmark has speed loss, what's the result of speed test then?
I notice it a couple of times a day minimum

MOVED: MSI Z87 GD65 Gaming and msata speed issue...

This topic has been moved to GAMING Motherboards.
https://forum-en.msi.com/index.php?topic=253613.0

Quote from: JLio01 on 06-March-15, 14:21:58
How often can you notice the problem? You mentioned AS SSD Benchmark has speed loss, what's the result of speed test then?
I notice it a couple of times a day minimum

MSI x79-GD65 (8d) RAM issue.

I've just recently bought a new pc. Put it together this week aswell, everything works fine except for the fact that my RAM is not capable of running quad channel. The problem is (as far as I've been able to diagnose it) that the slots to the right of the cpu, that's dimm slots 5-8, aren't working.
After installing all the parts and installing the memory in slots 1, 3, 5 and 7 (the black ones), I noticed that Windows only saw 8GB of ram rather than the full 16GB. I went into my BIOS (not clickbios but startup bios as that allows you to view Memory-Z) and found that it only detected the Ram in slots 1 and 3. I turned off the pc and put the ram in slots 5 and 7 into slots 1 and 3 to check if the ram was faulty. They were detected fine.
I put all of them in again but still no more than 8GB got detected. I swapped all the memory into the blue slots (2, 4, 6, 8). After doing so the computer wouldn't post. I then tried to boot with different ram (2 sticks of 2GB DDR3 1333mhz Mushkin) in slot 1 and 5 (that is 1 one the left and one to the right of the cpu). Only the ram in slot 1 got detected.
I then put the Mushkin in the first two black dimms (1,3) and put all the corsair ram into the blue slots (2, 4, 6, 8). No more than 12GB got detected (which was slots 1-4, 2x2gb and 2x4gb). Memory-Z confirmed that none of the ram in slots 5-8 got detected.
As a desperate last measure I took out the Mushkin ram and put the Corsair ram into slots 1-4. All of the ram got detected but for obvious reasons it was only running dual channel.
I've read on this and other forums that sometimes the cpu socket pins can be bent and that can cause memory problems, I took apart the pc again and looked at the pins, but none of them were missing nor were any bent.
The question now is how can I get quad channel ram working?
system specs
Motherboard: MSI x79-GD65 (8D)
Bios: Version 1.7 (latest version)
VGA: Gigabyte 670GTX OC
PSU: Corsair Enthusiast TX750M (750 Watt)
CPU: Intel Core i7-3820 (stock speed)
MEM: Corsair Vengeance CMZ16GX3M4X1600C9 (4 sticks of 4gb)
HDD: Corsair Force 3 240GB SSD.
+ 2xSamsung F3 1TB in raid 0, all on the Intel chip.
COOLER: Corsair H100
OS: Windows 7 64bit Ultimate

For quad channle you must populate DIMM1, DIMM3, DIMM5, DIMM7 or all slots if using 8 sticks. Populating slots 1-4 has to result in dual channel.
If 1, 3, 5 and 7 won't work there's some different problem that still would indicate bent pin(s).

Z97-GD65 mobo and Killer E2200 Ethernet controller issue

Hi there.
I recently bought a new board, a MSI Z97-GD65 Gaming and i'm happy with it, but I have a little problem I can't solve: My internet download rate is exactly 10MB/s when my connection can reach 20MB/s.
Following instructions of this forum I removed the Killer Ethernet Manager using the "Killer_clear(64bits)" and installed the stand-alone drivers for the Killer E2200 PCI-E Controller, but still suffering the same cut of download rate.
The only thing I could now is try to "transform" that controller into a "Qualcomm Atheros AR813X/AR815X/816X Series PCI-E Ethernet Controller", but I don't know if it would be the solution.
Anyone here has the same issue?
(BTW I use Windows 7 64bits FYI)
Thanks a lot!

Quote from: moist on 05-June-15, 03:21:27
Well, I bought a cheap PCI-e ethernet card, installed it, disabled the onboard E2200 killer, started Windows and I got 1,0Gbps in seven seconds without any other software installation need.
I don't know what's happening with Killer cards , maybe it's a driver issue or a faulty hardware, but i'm sure I won't buy in the future a motherboard that includes this network brand.
Honestly, I'm right there with you. I absolutely hate the Killer cards.....
Unfortunately, it's becoming harder and harder to get a motherboard without them, since all the OEM's seem to think that gamers want those cards on their computers. Personally, I hate them with a passion. The software is badly coded, and rarely works as expected.
The best thing I can suggest doing is using the drivers without the management software. This way you can still use the ethernet adapter, but not be limited by the management software. There should be a stickied post at the top of this forum I believe with information on it.

X79-gd65(8d) issues

I am running the board while waiting for delivery on my big bang xpower 2(another week or so)
system worked out the box, them flashed bios to 1.3
still worked, ran everything I threw at it
flashed bios1.5, worked
then randomly started freezing in MW3(after 2 weeks of no problems)
flashed bios to 1.61, wouldn't boot, code67
removed 7x dims, now boots on bios 1.4,1.5 and 1.61(network adapter takes forever to connect)
anti virus fails to start
added dim to slot 3(black) boots.
added dim 5(black)boots
added dim7(black)boots
add dim2(blue)boots
add dim4(blue)fails to post windows logon screen(code AA on board)
replaced dim 4 with other module, boots up, posts win logon but freezes before desktop
remove dim4, boots to desktop
add dim6(blue)boots
add dim8(blue)boots to desktop
test remaining dim in slot 1, boots.
Board or Bios problem?
system
x79-gd65(8d)
3960x processor
couger 1200W psu
H100 cpu cooler
patriot wildfire 120GB primary drive
32GB Geil evo 2 Ram 8x4GB modules
radeon 5870 (waiting for my 7970's, coming with board)
win 7 ultimate 64bit

What UEFI/BIOS version is on chip B? It's a simple matter to just test a new release & see how it does. If not satisfactory, switch chips to the known good version, set up to reflash the bad one to what works well. As Bernhard has mentioned, please be sure to let MSI Tech Support know. Not having any problems at all with .161 here.

MSI X79-GD65(8D) gives a posting error 63 Late CPU Initialize

Hey Guys.
I have recently purchased new hardware.
MSI X79-GD65(8D) Motherboard
Intel i7 3820 CPU
4 X Corsair Vengeance 4GB DDR3-1600 RAM
MSI GTX660Ti Power edition GPU
Corsair 750W Professional series PSU
Corsair H80 CPU Cooler
I haven't overclocked ht e mobo, but on cold boot, the mobo doesn't initialize, gives a post error 63, refered to the mobo manual, it says it means late CPU initialize. Checked the BIOS, running version 1.7 and according to MSI download site for the CPU support list.
The memory is in quad channel as it shows in a diagram in the mobo manual. If I switch the pc off, and back on, it initializes and boots, the pc runs stable, it can run 48 hours no hassle, passes burn in tests to, just the first cold boot doesn't initialize.
Any ideas for what to look at would be great.
Thank you.

A little hint for you: Don't try any of the .1B betas as they run horrible. I had to remove the latest .1B3 as it bricked the board and had to be recovered.
1.18 B7 is still the best bios to use:
Quote from: flobelix on 17-November-12, 00:49:07
I'd suggest the later Bios 1.18 B7 which I'm also using with the i7-3820 (https://forum-en.msi.com/index.php?topic=154186.msg1192427#msg1192427)

Gmail/Exchange email and calendar syncing issues

I have wiped my email accounts several times and entered in my data in the various ways as shown through the forums but my email accounts do no sync properly whether it is manual or active synced.
I read my emails in my gmail and my Microsoft exchange account and will delete or file them away but then when I check my accounts on my desktop, they are not synced as I've done so on my phone. I've also noticed that my calendars are not synced correctly either.
Could someone help me understand why and how these issues can be fixed? I'm in meetings for most of the day so I rely on my phone to keep me mobile. Was this a bad purchase?!?!

Hi JadeyMU,
How do you have your Microsoft Exchange account configured on your BlackBerry Z10? Are you using ActiveSync, BlackBerry Enterprise Server (BES), IMAP or POP?
Thanks.
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

My experience with Apple TV and HDMI/HDCP issues

I am convinced that it is the software update to 4.2.2 from 4.2.1 that is causing this issue. All forms of applications only worked once for me and then it reverted back to HDCP issues. I read several postings everywhere including plenty at Apple's forum and AVS where people were very frustrated with this HDCP issues. Anyways, here is what I did before taking it back to Apple store....I bought AUVIO high speed cables from Radio Shack which is rated very high and tried that and I still got HDCP issues when using NetFlix or AirPlay from iPad. Youtube from Apple TV always worked well without HDCP complaints.
I packed everything back and took it to Apple Store (you can return without re-stocking fee up to 14 days from the day of purchase). After 14 days, you cannot even return it and you can ONLY fix it. I waited for a Technician. They heard my complaints but didn't refute any of it (possibly because they have had numerous complaints on this product). It took 5 minutes inside for them to test and see similar issues with the box that I had. So, they have swapped it for a new box. Before I left the store, I checked the settings including software version and Audio/Video settings in the Apple TV that is connected at the store. I found three main differences none of which the Apple customer service staff agreed could be the reason for my problems (surprise!!)
1. The software update from the shelf and the one they were using was NOT updated to 4.2.2 (it was still running 4.2.1)
2. Because of the software update, the Audio/Video setting for HDMI had the options to toggle between Auto, RGBy, RGBhi & RGBlo bandwidth. I believe this was in place to make the HDMI interface output as component with higher or lower bandwidth but the newer update will ONLY give you the Auto option (!!!)
3. They had this directly Ethernet wired and not through Wireless network and were recieving the all the full bar strength signals. On the box that I returned, eventhough I have 18 Mbps speed at the house (any given time of the day), the Network speed test was taking a long time. Moreover, after the Apple TV network test, it doesn't spit out the outcome of the tests (a BIG bummer and useless for testing).
Anyways, I took the new box and hooked it up directly to my SONY BRAVIA XBR3 TV to one of the HDMI ports, disabled the feature to send or recieve data to Apple directly and did NOT update the software. It worked fine and have tested all of the options. From what I have read so far (I have only spent 30 hours of my weekend on this when Apple product hookups are supposed to take 5 minutes ONLY), there is NO guarantee that it will work continuously as people have had things work on them for 6 months and then suddenly have the HDCP issues.
Will wait to see....if it continues to work....

I figured it out. Had to go to general settings on the main screen and restart. Synch of audio is much better.

I have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3

i have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3.
the problem is best explained on the following one - page thread:
https://discussions.apple.com/thread/3951518?start=0&tstart=0
(Clearly i'm not alone in this problem, although i think i figured out what's going wrong a little more than he did...read on!)
his solution, to put mainstage in jump mode, is very unsatisfactory to me, as it bounces all of a sudden to drastically different settings.
basically, my analysis is that my controller is NOT receiving MIDI date from mainstage. in other words, mainstage knows what my controller is doing, but my controller doens't know what mainstage is doing.
let's say i turn the knob all the way to the right ... 127...and the virtual fader goes to the right like it's supposed to.
now...next...let's say i change to a different patch, where that same VIRTUAL fader is not at the max clockwise position..maybe it's only at 1pm. now when i turn the physical knob to the RIGHT, the midi data is still at 127 on the controller! it didn't "reset" to sync up with the new level (say 80 or so) setting on the new patch. so i can't increase that new setting of 80 by continuing to turn the knob to the right. i have to turn it all the way to zero,...and then continue PAST zero until the controller thinks that IT is at 0...at that point the controller and mainstage are in agreement, and things work fine....so bascially, the keyboard thinks the level is at max...but mainstage thinks the level is at 1pm.
i am using Logic 9, and i have a macbook pro 2.9 Ghz I7 with 8 gigs of memory and OS X 10.8.4

Hi Josh,
Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
Thanks.
Mike Towns

Interesting and an imporatant issue at sales order schedule line.

hi all,
interesting and an imporatant issue at sales order schedule line.
i created a sales order with 10 qty.and the system proposed a two schedule lines.
let's say to order created date is 27.11.2008.and the requested delivery date is 27.11.2008.
but the stock is not available today then the system proposed two more schedule lines apart from the 27.11.2008.so now there are three schedule lines like below.
schedule line date                      Material availabilyt date   delivery date
27.10.2008 with zero quantity.
28.10.2008 with 5 qty.                28.10.2008                     29.10.2008
02.10.2008 with 5 qty.                02.10.2008                     03.10.2008
now the delivery and pgi already for the schedule line 28.10.2008.
then when i run the availability check on 01.11.2008 system is over writing the material vailability date as today at the scheduleline number two.
now i can able to view only two schedule lines only.
schedule line date                      Material availabilyt date   delivery date
28.10.2008 with 5 qty.                01.11.2008                     29.10.2008
02.10.2008 with 5 qty.                01.11.2008                     02.11.2008
now my concern when we reschedule the avalability check it should notchange the Material availability date of the schedule line which i already delivered.
Regards,
sheshukumar

can any one repsond for this.....

I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for

I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for the HP driver when i boot up. It also will not save in any print or postscript format. Does anyone know how to fix?
Currently use a Mac with the latest Mavericks 10.9.4

Oh boy! Acting kind of weird seems to be an understatement, aquaequus!
What type of troubleshooting were we able to do with you? I want to make sure that we can get some sort of resolution for this problem.
It is quite possible the battery door may get your phone in working order again. I'm not sure if the store has it in stock, but it is available in our warehouse for $14.99 which can be ordered via customer service.
Tamara H.
Follow us on Twitter @VZWSupport

Report Builder - Last page issue and Report Footer issue

I am using ColdFusion 9 Report Builder, am new to this product and encountering 2 issues.
Issue 1 - I have a field that I would like to print on the last page of my report. How can I determine the last page? I initially tried using a calculated field set to the 'highest' calc.Page_Number. Then I could compare the current page to the last page in the 'Print When' property. But calc.Page_Number can not be used in a definition of a calculated field.
Issue 2 - Depending on the amount of report detail, sometimes my report footer prints alone, without a page header and page footer. The report includes this page in the total number of pages. For example, if it is a 2 page report, the page header on page 1 will display Page 1 of 2. Then the only data on Page 2 is the Report Footer. No page header or page footer prints.
Any assistance on these issues would be most appreciated. To date, using the Report Builder has not been easy.

To issue 1: The report contains a report band called report footer. thsi is always at the last page. The report footer band initially is collapsed, so you have to expand it by dragging the last band divider.
To issue 2: I guess this is a page break calculating error when detail data reaches really near the page footer area.
Try some experiments with different setting of the following properties/issues:
- in elements, e.g. calculating fields in the bands between report detail and page footer: In Properties / Print Control / Printing Options: Activate the option "Remove line when blank". This will remove the whole report band area if this field is blank. May save some empty space.
- try to remove unused empty space between detail rows.
- try to resize and reposition all detail fields so that they snap to the grid.
Best regards

Just bought a new iPhone and am having trouble with iTunes and App Store. I can log in to Cloud, iTunes, and app store but once I try to download, it says "Youe apple id has been disabled". I've reset my password three times and have no issue on my Pad.

Just bought a new iPhone and am having trouble with iTunes and App Store. I can log in to Cloud, iTunes, and app store but once I try to download, it says "Youe apple id has been disabled". I've reset my password three times and have no issue on my Pad.

Hi FuzzyDunlopIsMe,
Welcome to the Support Communities!
It's possible that resetting your password multiple times has triggered this security. Click on the link below for assistance with your Apple ID Account:
Apple ID: Contacting Apple for help with Apple ID account security
http://support.apple.com/kb/HT5699
Here is some additional information regarding your Apple ID:
Apple ID: 'This Apple ID has been disabled for security reasons' alert appears
http://support.apple.com/kb/ts2446
Frequently asked questions about Apple ID
http://support.apple.com/kb/HT5622
Click on My Apple ID to access and edit your account.
Cheers,
- Judy

The Ultimate Guide to Resolving Profile and Device Manager Issues

The following article also applies to issues after re-setting the severs' hostname. It also applies to situations where re-setting the Code Signing Certifictateas described by Apple has not resolved the issue.
Hello,
I have been plagued with Profile Manager and Device Manager issues since day one.
I would like to share my experience and to suggest a way how to resolve issues such as device cannot be enrolled or Code Signing Certificate not accepted.
I shall try to be as brief as possible, just giving an overview of the steps that resolved my issues. The individual steps have been described elsewhere in this forum. For users who have purchased commercial SSL certs the following may not apply.
In my view many of these issues are caused by missing or faulty certificates. So let us first touch on the very complex matter of certificates.
Certificates come in many flavours such as CA (Certificate Authority), Code Signing Certificate, S/MIME and Server Identification.
(Mountain?) Lion Server creates a so-called Intermediate CA certificate (IntermediateCA_hostname_1") and Server Identification Certificate ("hostname") when it installs first. This is critical for the operation of many server functionalities, including Open Direcory. These certs together with the private/public keys can be found in your Keychain. Profile and Device Manager may need a Code Signing Certificate.
The most straightforward way to resolve the Profile Manaher issues is in my view to reset the server created certicates.
The bad news is that this procedure involves quite a few steps and at least 2 hours of your precious time because it means creating a fresh Direcory Master.
I hope that I have not forgotten to mention an important step. Readers' comments and addenda are welcome.
I shall outline a sensible strategy:
1. Clone your dysfunctional server to an external harddrive (SuperDuper does a reliable job)
2. Start the server fom the clone and shut down ALL services.
3. It may be sensible to set up a root user access.
4. Back-up all user data such as addess book, calendar and other data that you *may* need to set up your server.
5. Open Workgroup Manager and export all user and workgroup accounts to the drive that you using to re-build your server (it may cause problems if you back-up to an external drive).
6. Just in case you may also want to back-up the Profile Manager database and erase user profiles:
In Terminal (this applies to Lion Server - paths may be diferent in Mountain Lion !)
Backup: sudo pg_dump -U _postgres -c device_management > $HOME/device_management.sql
Erase database:
sudo /usr/share/devicemgr/backend/wipeDB.sh
7. Note your Directory (diradmin) password for later if you want to re-use it.
8. Open Open Server Admin and demote OD Master to Standalone Directory.
9. In Terminal delete the old Certificate Authority
sudo rm -R /var/root/Library/Application\ Support/Certificate\ Authority/
This step is crucial because else re-building you OD Master will fail.
9. Go back to Server Admin and promote the Standalone Directory to OD Master. You may want to use the same hostname.
10. When the OD Master is ready click on Overview and check that the LDAP and Keberos Realm reflect your server's hostname.
11. Go back to Workgroup Manager and re-import users and groups.
NOTE: passwords are not being exported. I do not know how to salvage user passwords. (Maybe passwords can be recovered by re-mporting an OD archive - comments welcome! ).
12. Go to Server App and reset passwords and (not to forget) user homefolder locations, in particular if you want to login from a network account!
If the home directory has not been defined you cannot login from a network account.
13. You may now want to restore Profile Manager user profiles in Terminal. Issue the following commands:
sudo serveradmin stop devicemgr
sudo serveradmin start postgres
sudo psql -U _postgres -d device_management -f $HOME/device_management.sql
sudo serveradmin start devicemgr
14. You can now switch back on your services, including Profile Manager.
In Profile Manager you may have to configure Device Management. This creates a correct Code Signng Certicate.
15. Check the certificate settings in Server App -> Hadware -> Settings-> SSL Certificates.
16. Check that Apple Push Notifications are set.(you easily check if they are working later)
17. You may want to re-boot OS Server from the clone now.
18. After re-boot open Server App and check that your server is running well.
19. Delete all profiles in System Preferences -> Profiles.
19. Login to Profile Manager. You should have all users and profiles back. In my experience devices have to be re-enrolled before profiles can be pushed and/or devices be enrolled. You may just as well delete the displayed devices now.
20. Grab one of your (portable) Macs that you want to enrol and go to (yourhostname)/mydevices and install the server's trust profile. The profile's name should read "Trust Profile for...) and underneath in green font "Verified".
21. Re-enrol that device. At this stage keep your finger's crossed and take a deep breath.
22. If the device has been successfully enrolled you may at last want to test if pushing profiles really works. Login to Profile Manager as admin, select the newly enrolled device. Check that Automatic Push is enabled (-> Profile -> General). Create a harmless management profile such as defining the dock's position on the target machine. (Do not forget to click SAVE at the end - this is easily missed here). If all is well Profile Manager will display an active task (sending) and the dock's position on the target will have changed in a few seconds if you are on a LAN (Note: If sending seems to take forever: check on the server machine and/or on your router that the proper ports are open and that incoming data is not intercepted by Little Snitch or similar software).
Note: if you intend to enrol an Apple iPhone you may first need to install the proper Apple Configuration software.
Now enjoy Profile and Device Manager !
Regards,
Twistan

HI
1. In Action profiles, logon to system and recheck correcion are available in action definition as well in condition configuration and the schedule condition is also maintained. but the display is not coming(i.e in the worklist this action is not getting displayed).
You can check the schedule condition for the action and match the status values...or try recreating the action with schedule condition again....for customer specific ....copy the standard aciton with ur zname and make a schedule condition and check the same.
2, In suppport team of incident when i give individual processor it throwing a warning that u r not the processor. but when i give org unit it is working perfectly. Could anyone guide on this.
You need to have the empolyee role for BP ..goto BP and got here dropdown for ur bp and choose role Employee and then enter ur userid
also make sure that u have the message processing role
Hope it clarifies ur doubt and resolve ur prob
Regards
Prakhar

X79-GD65 (8D) and i7 3820 issues

Similar Messages

Maybe you are looking for