X86 install was successful, but now I can't boot from the hard drive

I have successfully installed Solaris 10 for x86 from the bootable CD ROMs. However, now, after removing the CD-ROM from the drive and booting from the hard disk I am having problems.
The system attempts to boot. It displays the Solaris Primary Boot Subsytem v2.0 screen...pauses for 15 seconds...then reboots itself. And it continues this process.
However, if I boot to CD-ROM first, then boot to the Hard Drive, I have no problems. The CDE comes up fine.
We are running a 64 bit OS with a SATA drive that is supported. And as I mentioned, the install successfully completed.
Any thoughts are greatly appreciated.

is your hard drive connected as IDE0 - primary master? if not try doing so.

Similar Messages

HP Pavilion 500-210 QE Can't boot from any hard drive.

Good Evening. As you can see from the subject, my computer just can't boot from any hard drive that I put on it. I tried swapping the power supply, the SATA cable, resetting the BIOS, enabling legacy boot, changing from AHCI to IDE and RAID...
When I get to the BIOS setup, I can see the hard drive and its specifications, but it just won't boot or show up when I'm trying to install a new OS. I'm not an expert, but I think the problem might be in the motherboard SATA ports, but I'm not sure. Just to make sure, I did try another hard drive and it didn't work aswell.
I was also thinking about buying an external hard drive and instaling my OS on that, but I don't even know if that's possible and I would really like to have my computer working again.
Thank you for your attention!
This question was solved.
View Solution.

What is the installed operating system?
Did you make a recovery disk set?
Did you happen to make a Windows 8.1 startup disk or USB recovery thumbdrive?
Have you tested the hard disk?
Press the power button and then immediately tap the Esc key. In the Startup menu, choose F2 for Diagnostics. In the HP Basic System Diagnostics menu choose hard disk. Run the test and post the results here.
The issue you are facing has nothing to do with the SATA ports. It is a configuration issue. Your PC is a modern one and its BIOS (UEFI) is far more advanced than what you may have seen before.
If you want to install a different operating system then you will have to make a few changes in the BIOS configuration. Secure Boot is turned on by default for Windows 8 and Windows 8.1. If you try installing a different OS without turning this off then your system won't boot up. You may be running into this if you are trying to install another operating system.
The image below is what will be seen in the BIOS of your PC in the security tab --> . In the secure boot configuration options do not clear the secure boot keys! Those keys are your operating system license activation keys.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Can't boot from external hard drive

I have a 250 GB OWC Mercury Elite-AL Pro Firewire drive that I use for backups for my MacBook Pro (running 10.4.8) and iBook G4 (running 10.3.9). The drive is partitioned into four parts, two of which I use for bootable clones of the MBP and iBook. I've been able to boot from the MBP clone, but whenever I try to boot from the iBook clone, after a few seconds of the gray screen with the Apple logo on it and the spinning circle, the Apple logo turns into a gray circle with a diagonal line through it, and the spinning thing keeps spinning, and it never boots up. (For lack of a better description, the circle with the line through it is a gray version of the symbol you see, for instance, in the Ghostbusters logo.)
Here's a few things that aren't (or don't seem to be) the problem:
- I'm not trying to boot from the wrong machine--i.e., I'm not trying to boot the iBook clone from the MBP
- Since I've tried creating the clone with both EMC Retrospect Express and SuperDuper and get the same result with both, it doesn't seem to be the backup software
- I've tried completely erasing the partition (including erasing the free space) from both the MBP and the iBook before creating the clone
- Just for good voodoo, I've also repaired permissions, reset the NVRAM, and run a disk repair on both the internal iBook disk and the clone
- The iBook definitely recognizes it as a bootable drive, since it shows up when I hold down the option key during boot, and also in the Startup Disk section of System Preferences
I'm a little stymied at this point. The only other things I can think of would be that (a) I need to completely reformat and repartition the drive (which I don't really want to do, since I also have other backups and data on there), or (b) for some reason the fact that I initially created the partitions on the MBP is preventing the iBook from using those partitions (i.e., I can only create Intel-only or PPC-only partitions, which I hope isn't the problem, since that would mean I'd need a whole separate drive just to back up the iBook).
Anyone have any idea what's going on?

The MBP and iBook require different partition schemes to be bootable. You won't be able to boot both computers from the same drive.
I can't install Mac OS X on a hard drive
If the installer won't let you install Mac OS X on a hard drive and gives as the reason "Mac OS X cannot start up from this volume," the drive may not have the partition scheme that the Installer requires. The needed partition scheme depends on the type of processor in your Mac. The installer installs Mac OS X for Intel-based Macintosh computers only on drives with the GUID partition scheme. It installs Mac OS X for PowerPC-based Macintosh computers only on drives with the Apple partition scheme.
To check the external drive's partition scheme, open Disk Utility, select the drive in the list, choose File > Get Info, and look for the "Partition Type." If you can't see the "Partition Type," you may have selected the volume instead of the disk. (Drives are flush left, with their volumes indented to the right below them.)
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh2315.html
John

Trying to install SL on a new hard-drive for my iMac, when asked which disk to install on it gave me no options, i followed advice from another forum and created a partition, now can't boot from the new drive at all. Help?

I've had **** with my iMac, the hard-drive failed so i replaced it with a new 1TB Samsung drive. Then when i tried to install SL from the install disk, all went to plan until it asked me which drive i wanted to install it on, where it came up with a box where my options should have been, but instead it didn't give me any options to install it on any drive i.e. it asked which drive i wanted to install it on but no drives came up to select.
So i followed the advice from another forum, look at the 'Extended Hard-drive preparation' response
( https://discussions.apple.com/message/10576009#10576009 )
After following these instructions i have now got a new partition, but when i restarted my computer to install SL on the drive, the option to boot from the drive is now not available, now i must boot from the install disk, whereas before i was able to boot from either the install disk or the hard drive. The hard drive is still visible in disk utility as it always has been, but i am now unable to boot from it, let alone install SL.
Please help my iMac has been broken for months and i've been trying to fix it for so long and am getting problem after problem. Thank you!
<div class="mcePaste" id="_mcePaste" style="position: absolute; left: -10000px; top: 0px; width: 1px; height: 1px; overflow-x: hidden; overflow-y: hidden;" mcestyle="position: absolute; left: -10000px; top: 0px; width: 1px; height: 1px; overflow-x: hidden; overflow-y: hidden;"></div>

Hi db2
That off the shelf MS-DOS / FAT-32 drive needs to re-partitioned GUID Partition Table / Mac OS Extended (Journaled) before you can install OS X and Startup your Intel iMac from it.
1. Boot from your original install or retail SL DVD and open Disk Utility.
2. Highlight the new HD in the list of drives and select the Partition tab.
3. Under Volume Scheme select 1 Partition and click on the Options... button.
4. Select GUID Partition Table in the drop down window and click OK.
5. Set the Format to Mac OS Extended (Journaled) and click the Apply button.
6. Once thats done, then you can do a clean SL Install, Restore from TM , your old HD or Bootable Clone.
Dennis

Did a little too much maintenence - now I can't boot from my system drive

I figured I'd watch the Bears game this afternoon and do a little maintenence on my G4/733, currently runnint 10.4.9.
I booted from an older (10.3.9) system disk I have in the computer, Verified the disk (all was well, no repairs needed), then booted from my Disk Warrior (Tiger) disk and rebuilt the directory. Booted from the newly verified and rebuilt disk and it started up fine. Then ran Onyx and emptied several caches, including the system cache and kernel cache. Ooops, no longer boots...instead, I get the grey Apple screen, and then it just sits. When this happened the first time, I reset the PRAM by pressing the restart button six times...still no boot action.
The drive mounts fine, and so I'm in the process of copying the entire volume over to an external drive before performing any more maintenence. I can't do an archive and install from my supplied OS disc, as it's a lower OS version than I'm currently running. I'm loathe to do an erase and install, as then I get to perform the always-painful "make the computer work like it used to" process. And, the maintenence steps I've taken on this drive are nothing I haven't done recently on my other two Macs (both now running 10.4.10), both of which are running fine. So I'm still classifying this glitch as "minor".
Any suggestions out there? I'm gonna try to repair the disk again, and then run the OS 10.4.10 upgrade, unless I hear different from anyone here. Idears?

I had a similar problem. A mac started doing wierd things like not starting. All the tests showed no problem except one..I ran TechTool and did a full surface scan. It showed some bad blocks. The only way to repair was to clone to a back-up----erase and zero out the whole drive---then restore from the back-up.
That cured it....even a disk utility did not see the error.
Bad blocks can happen anytime, it may be no big deal but if this is your problem check it every so often and if more start showing up....start shopping..
Cheers,
Glynn

Can anyone help. I need to reuse my SDHC cards and transfer footage from an ongoing profect to a hard drive. Can i edit from the Hard drive or am I better transferring info striaight from camera to time line

Hi I am using a JVC GY-HM100 camera which is meant to work well with final cut pro. I have an ongoing project but need to save money and resuse the SDHC cards that are currently full of footage.
Would I be better off transferring the footage straight to the time line (as rumour has it you can do this with this camera) or store the footage on a hard drive and edit it later without risk of losing the footage.
Many thanks
Lindabob

Thanks Linda,
Here's some more info for you:
This is my pet checklist for questions regarding FCP X performance - you may have already addressed some of the items but it's worth checking.
Check the spec of your Mac against the system requirements:
http://www.apple.com/finalcutpro/specs/
Check the spec of your graphics card. If it's listed here, it's not suitable:
http://support.apple.com/kb/HT4664
Make sure you're using the latest version of the application - FCP X 10.0.3 runs very well on my 2009 MacPro 2 x 2.26 GHz Quad-Core Intel Xeon with 16 GB RAM and ATI Radeon HD 5870 1024 MB. I run it with Lion 10.7.3.
Check that you have at least 20% free space on your system drive.
If you have not already done so, move your Projects and Events to a fast (Firewire 800 or faster) external HD. Make sure the drive's formatted OS Extended (journalling's not required for video). You should always keep at least 20% free space on the Hard Drives that your Media, Projects and Events are on.
If you are getting crashes, there is some conflict on the OS. Create a new (admin) user account on your system. Do NOT import any of the settings etc from the old account - simply use FCP X from there - if it runs a lot better, there's a conflict and a clean install would be recommended - but remember, if you reinstall the system, and then use Migration Assistant (or anything else) to import all your old settings etc etc, you may well be importing the cause of the conflict in the first place.
Keep projects to 20 mins or less (about half that for Multicam). If you have a long project, work on short sections, make them into Compound Clips and then paste these into a final project for export.
If you ever experience dropped frames, I strongly recommend you use ProRes 422 Proxy - it edits and plays back like silk because the files are small but lightly compressed (not much packing and unpacking to do) - but remember to select 'Original or Optimised Media' (FCP X Preferences > Playback) just before you export your movie, otherwise it will be exported at low resolution.
If you have plenty of processor power, for the ultimate editing experience, create Optimised Media - most camera native files are highly compressed and need a great deal of processor power to play back - particularly if you add titles, filters or effects. ProRes 422 takes up much more hard drive space but is very lightly compressed. It edits and plays back superbly.
Hide Audio Waveforms at all times when you don't need them (both in Browser and Storyline / Timeline). They take up a lot of processor power. (Use the switch icon at the bottom-right of your timeline to select a format without waveforms if you don't need them at the moment, then switch back when you do).
Create folders in the Project and Events libraries and put any projects you are not working on currently, in those folders. This will help a lot. There's a great application for this, called Event Manager X - for the tiny cost it's an invaluable application.
http://assistedediting.intelligentassistance.com/EventManagerX/
Unless you cannot edit and playback without it, turn off Background Rendering in Preferences (under Playback) - this will help general performance and you can always render when you need to by selecting the clip (or clips) and pressing Ctrl+R.
The biggest single improvement I saw in performance was when I upgraded the RAM from 8 GB to 16.
Andy

Can't boot from IDE hard drives

Just purchased a barebones system with a KEN NEO Platinum board running an AMD 64 3400+. Tried to install old Maxtor hard drive (40 gb) into new system and a blue screen pops up for less than one second and reboots PC. I can’t read the blue screen but I believe it is saying there is a hardware conflict.
What is causing this. The CMOS recognizes the HD but it can't boot from it. I’ve got two of these units and both have the same problems. I put the drive back into the original PC and it works fine.
Need help desperately.

When I connect the cables, they show which is the slave and which is the master. In the CMOS, everything looks fine. I've noticed alot of people are having difficulty installing used and new hard drives. I've been working with PC's for quite a while and I've never had this much trouble. I was hoping there was something I missed in the CMOS settings.

Can't boot from internal hard drive.

I just replaced my internal hard drive and copied the back-up from the old drive onto the new one. The new drive appears to be properly formatted and to contain all the data I copied to it, but I am unable to boot from it. Any advice? Thanks!

Thanks, Courcoul. I went back and formatted the drive again, this time booting from the OSX installation CD. (Last time I booted from the back-up drive from which I was copying.) I don't know if it was booting from the CD and not the drive, or that I didn't format it properly the first time, but this did the trick. Working perfectly.

Can't Boot from Second Hard Drive

I put a second SSD hard drive into the bay for a second hard drive but I'm unable to boot from it even after making it the primary drive in the computer settings.
Both hard drive are running Windows 8 if that makes a difference.
Any ideas?

Do you have an Intel version of OS X installed on the external drive and did you partition the external drive using the GUID partition scheme? If not then that's your problem. Also, depending upon which model MBP you have you may require a later version of OS X. According to my information the C2D 17" MBP requires at least 10.4.8 (the build that came on the OS X Installer discs that came with the computer.) 10.4.6 will not boot that model.

I have Lightroom 4. My external hard drive crashed and now my file is missing from the hard drive.In Lightroom, it has ? on the photos used. I've backed up the photos onto another hard drive and wanted to use it so I can work on my folder of images. Can s

How can I use my backup external hard drive to sync into Lightroom and still work on the same photos I was working on and get rid of the ?. The photos are on a folder so I need to someone sync the folder into Lightroom. Please help!

When I right click on an image, then went to Go to Folder in Library, it pulls up the new external hard drive where I made the new link. When I try to work on the photos, the image still says file image is offline or missing. When I right click on the image to Show in Finder, it says the image could not be used because the original file could not be found. I eventually did click on their locate and found the image. When I linked those two together, a few minutes later ALL the "?" went missing and now IT WORKS!!!!
That was weird!
Hope this helps someone else in my predicament.

Can't boot from external hard drive with Snow Leopard

I bought a new Macbook Air with Lion. I have my old Snow Leopard installation cloned onto an external hard drive, and I want to boot from it. I can choose my external hard drive during boot, it shows the Apple logo, but after that the screen goes black and nothing happens. Is there a way to fix this?

Can't be done. Snow Leopard does not contain necessary drivers and perhaps other items required for OS X on the 2011 MBA. In fact, the version of Lion on the App store won't install on the 2011 MBA.
This is totally normal in Apple's world. A new version of MAC hardware that comes with a new version of OS X installed usually will not operate correctly with previous versions of OS X.

Disk repair failed how can I back up my files when I can't boot from the start up disk

When disk repair fails, and I can't boot from the hard drive how can I get to my files to back them up. I have a seagate 1 TB connected to the USB port.

Perubbit,
which model MacBook Pro do you have, and which version of OS X is installed on it?

Can I boot from a SATA drive? What if it's RAID?

I'm planning on getting the MSI 875P Neo FIS2R 800FSB motherboard. I'm also planning on getting ONE SATA hard drive. Can I boot from the SATA drive? Do I HAVE to set up it as a RAID drive? Can you boot from RAID drives? RAID and SATA confuse me a little. Anyone care to help?

I'm using the MSI 865PE Neo2 board and I'm having this problem. It probably has an easy solution, but this is my first build, so I'm not sure exactly what to do.
MSI 865PE Neo 2 Mobo
2.4b P4
Seagate SATA 80GB HDD
Panasonic FDD
Lite-On DVDROM
It took me a little bit of experimenting, but I got the BIOS to recogonize the DVD & HDD. It seems every time I got it to recognize one, the other disappeared. Anyway, like I said, BIOS recognizes all 3 now.
I go to install XP and it says I need to install the drivers from a floppy (after I had previously hit F6). Well, where do I get the drivers? I have a CDROM that came with the mobo but I don't know where to find the drivers for the SATA controller on it. ???
Can someone help me by directing me to a download and/or the file names that I need to transfer to floppy for Win XP installation? I would appreciate it. Thanks.

I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created.

I tried partitioning my HD to install linux, the installion was not successful and now I can't boot my mac, I tried internet recovery, it was not helpfull as the disk utility cannot delete the partition I created. It was only showing me an error message "EFI files are missing", I realized that it is trying to boot from the new partition I created for the installation of the linux I intended to do.

It sounds like you may have multiple problems, but none of them are likely to be caused by malware.
First, the internet-related issues may be related to adware or a network compromise. I tend to lean more towards the latter, based on your description of the problem. See:
http://www.adwaremedic.com/kb/baddns.php
http://www.adwaremedic.com/kb/hackedrouter.php
If investigation shows that this is not a network-specific issue, then it's probably adware. See my Adware Removal Guide for help finding and removing it. Note that you mention AdBlock as if it should have prevented this, but it's important to understand that ad blockers do not protect you against adware in any way. Neither would any kind of anti-virus software, which often doesn't detect adware.
As for the other issues, it sounds like you've got some serious corruption. I would be inclined to say it sounds like a failing drive, except it sounds like you just got it replaced. How did you get all your files back after the new drive was installed?
(Fair disclosure: I may receive compensation from links to my sites, TheSafeMac.com and AdwareMedic.com, in the form of buttons allowing for donations. Donations are not required to use my site or software.)

HT201612 I was trying to install windows using boot amp but now I can't boot my MaOckbook pro again

I was trying to install windows using boot amp but now I can't boot my MacBook pro again

Go to the Windows Control Panel and select Boot Camp applet. In that applet there is a Boot Drive option. Select Mac OS X.
Or restart the system and hold down the Option key for a few second. A Boot Menu screen will come up. Select Macintosh HD.
Once in OS X go to the Sys Prefences, Startup Disk and select Macintosh HD Mt Lion 10.8.2 and click Restart then Restart again. the system will now restart in Mac OS X.
To boot back to Windows do the same, Startup Disk, and select Windows then Restart and Restart again.

X86 install was successful, but now I can't boot from the hard drive

Similar Messages

Maybe you are looking for