X86: Solaris does not boot correctly?

I have installed Solaris on a second hard disk.
When I boot my computer on the second hard disk, I get the Solaris 10 emergency booting system which tries to find out on which hard disk I would like to boot Solaris 10.
Is there a possiblity to save my settings once for all time?
Because on every time I boot, I got the Solaris emergency boot manager to rechoose the disk on which I should boot.

Since a similar thing happens after other updates, it probably is not directly related to "uninstalling google desktop." Does the same thing sometimes happen when you do a regular restart (with no update or uninstall)?
You can try doing a SMU (power management) reset. Before you do that, reset PRAM.
http://support.apple.com/kb/HT1379
If that does not help, follow this procedure precisely to reset the SMU
http://support.apple.com/kb/HT1767
When you reconnect the power cord, if you were using an power strip of some kind (especially if it's old or overcrowded), try connecting it directly to a wall outlet by itself (at least initially). Start it up with only the power cord connected, then (if it starts up normally), add only standard USB keyboard and mouse. Use it that way for a while to see if there's improvement. If it's better, add your other peripheral devices back, one at a time, to see if the problem returns.

Similar Messages

Satellite M30-107 does not boot correctly after Recovery disk usage

Hi
I've recently got hold of a second hand toshiba Satellite M30-107 laptop, and decided to freshen it up.
I used the toshiba recovery disk, but after doing so the laptop no longer loads windows.
When turned on it shows the Toshiba start up disk for about a second then goes to a blank screen and freezes.
When turned off and on again a screen comes up reporting an error in shutting down and gives the options to start in safe mode etc. but choosing any of the options causes the machine to freeze.
Any help or advice would be much appreciated.
Thanks
jt

Hi
Sounds a little bit like the notebook does not boot due to the Windows software issue
Did you recover the M30 with the original Toshiba recovery CD which was supplied with this M30 unit?
Maybe Im wrong but for me it looks like a wrong recovery CD was used and an image with non compatible drivers was installed
You could try to install the OS from original Microsoft Win XP CD and could check if it would be possible to get the notebook ruining using clean OS.
In such case we ( you and me ;) ) could find out if this issue could be related to the software or hardware.
Bye

Arch Linux USB installation does not boot Correctly [SOLVED]

Hello,
I created a bootable USB stick with Universal USB Installer on a Windows System.
When I try to boot it, it shows me a Gummiboot Boot Loader Switch, where I can switch between two EFI shells and ArchLinux installation media.
When choosing the installation media, the screen flashes and after that, it shows the following lines:
:: running early hook [udev]
:: running hook [udev]
:: Triggering uevents ...
:: running hook [memdisk]
:: running hook [archiso]
:: running hook [archiso_loop_mnt]
:: running hook [archiso_pxe_common]
:: running hook [archiso_pxe_nbd]
:: running hook [archiso_pxe_http]
:: running hook [archiso-pxe_nfs]
:: Mounting '/dev/disk/by-label/ARCH_201403' to '/run/archiso/bootmnt'
Waiting 30 seconds for device /dev/disk/by-label/ARCH_201403 ...
[ 5.060855] sd 6:0:0:0: [sdc] No Caching mode page found
[ 5.060960] sd 6:0:0:0: [sdc] Asuming drive cache: write trough
[ 5.062636] sd 6:0:0:0: [sdc] No Caching mode page found
[ 5.062688] sd 6:0:0:0: [sdc] Asuming drive cache: write through
[ 5.064566] sd 6:0:0:0: [sdc] No Caching mode page found
[ 5.064614] sd 6:0:0:0: [sdc] Asuming drive cache: write through
ERROR: 'dev/desc/by-label/ARCH_201403' device did not show up after 30 seconds ...
Falling back to interactive promt
You can try to fix the problem manually, log out when you are finished
sh: can't accsess tty; job control turned off
[rootfs /]#
In UEFI menu I unabled secure boot and fast boot.
Can anybody tell me what I can do to boot the istallation media correctly?
Thanks for your suggestions
Last edited by outschi (2014-03-20 00:31:18)

Welcome to arch. I suspect this is the problem:
outschi wrote:I created a bootable USB stick with Universal USB Installer on a Windows System.
The error message you get is the same as those encountered by people who try to use unetbootin (eg here). I know Unetbootin does not work to create bootable arch media - perhaps the windows tool also doesn't.
Did you see and follow the tip here? It seems that tool will create working usbs, but you have to fix the label.
Last edited by Trilby (2014-03-19 16:52:22)

Satellite M40-129 BSOD and does not boot correctly

Hi again.
I was working on my computer since my last question, but (almost) nothing changed.
To the problem:
My Notebook is booting, but only on very rare occasions.
What can happen:
- the screen stays black (almost 50% the case)
- The start screen (Toshiba- In touch with tomorrow) becomes visible and nothing happens then (40% )
- the notebook boots "properly" (10%)
if the notebook boot properly there are 2 options:
1st: I try to start Windows: it crashes with a bluescreen with the nice ask for an BIOS update.
2nd: I start SuSe Linux: EVERYTHING WORKS!
I tried to update the BIOS the traditional way and although it's hard to get it booted it works till short before the end and the computer restarts.
I see no confirmation screen as Im used to.
From this I asume, that the boot-problem is BIOS related.
I read of a BIOS recovery method with a floppy disk, where you copy the BIOS.ROM to the disk and start the notebook with the disk.
My question is: Is it also possible with an CD (have no floppy drive), if yes: how to do this?
I wanted to give it to a service point of Toshiba, but if they cannot fix it, I still have to pay 50Euro. I would pay the money for getting my BIOS restored, but the service point seems to be just a "delivery-service" to the true service point and I would like to speak with a qualified person first :)

>I read of a BIOS recovery method with a floppy disk, where you copy the BIOS.ROM to the disk and start the notebook with the disk.
>My question is: Is it also possible with an CD (have no floppy drive), if yes: how to do this?
Hmm you said you have already received the traditional BIOS files from the ASP in your country. So maybe you should take a look into this Toshiba document:
[How do I update the BIOS on my Toshiba Notebook and where can I get the latest BIOS for my machine?|http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/faq.jsp?z=234&service=EU&from=faq_selection&CFID=B IOS&FID=TRO0000000b07]

Boot failed: solaris server does not boot

Hi All,
one of my support person who has administrator previlages tried move the contents of root to trash directory, in the middle it got hung,and he had restrted the server.
Now the solaris does not boot. It says
boot failed
Enter Filename [platform/sun4v/kernel/sparcv9/unix]
and what ever we enter there it says boot cannot read.
Please suggest some workaround, nearly 200 users are down, actually it is our licnese server.

Hi,
What you could try is the following :
Boot the system from the solaris cd into single user mode.
Find out what the disk is you need to mount and mount it under /a
After you have done this you can see if you can move back the stuff that was moved from the root directory to the trash.
If that works then you could try and boot again from the disk to see if everything works again.
Nico

System does not boot during Hyper V installation

Hi -
I was trying to install Hyper V on my Windows 8.1 professional edition, 64 bit OS. The installation was through ISO downloaded through MSDN. During installation I had to hard boot my system through switch off. Now my system does not boot correctly and during
boot it flashes a message "The last windows installation did not complete please install the setup". Does this mean that my existing 8.1 OS has crashed ? how can i come out of this and recover my data ?
My hardware configuration is :
i7 processor, 16GB RAM, intel graphics Card, windows 8.1 professional 64 bit OS.

Hi RahuIM,
You can try to enter safe mode then copy your personal data to the data volume then reinstall the system.
The related KB:
Start your computer in safe mode
http://windows.microsoft.com/en-us/windows/start-computer-safe-mode#start-computer-safe-mode=windows-7
Step-By-Step: Enabling Hyper-V for use on Windows 8.1
http://blogs.technet.com/b/canitpro/archive/2014/03/11/step-by-step-enabling-hyper-v-for-use-on-windows-8-1.aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Reset Password - System does not boot from DVD

My System: Macbook Pro - 2Ghz Intel Core Duo - OS X - 10.6.8
Hi everyone,
i forgot my password. So i want to boot from install DVD to reset the password. Unfortunately my macbook pro does not boot from DVD (10.6.3).
I press c all the time...but sometimes the macbook pro throws the DVD out...and sometimes nothing happens.
The DVD drive is working fine...
Any other idea?
Thanks in advance.
Fabian

So when you boot holding option it shows a padlock with a password field? Is that correct?
In that case we're talking about the firmware password, which you can't reset via the install disk. There is only one way to do this, I'm not certain if one is allowed to divulge that information publicly - might want to try googling "reset firmware password"

KT6V + sempron 2800 does not boot when BIOS saved

Hi,
I have just bought a new sempron 2800 to be use on a KT6V LSR. I plugget in my KT6V but was not recognised well (but all was working ok with windows). To be recognised, I have flashed with the last bios of MSI my motherboard... and now I have the following problem:
- I clear CMOS, then boot. It comes ok (processor detected and set a 1200Mhz)
- Then CMOS has a bad checksum: I enter setup, then load default, save.
- I reboot: the computer does not boot up.
If I re-clear CMOS I can re-enter setup and modify frequencies or other options. But when I save my modifications, then the computer does not reboot anymore (I have to re-clear cmos again)...
I tried to apply the configuation I found in this thread:
http://forums.amd.com/lofiversion/index.php/t69536.html
It says that SDRAM must be at 333, FSB at 166 and multiplicator at 12. When applying this settings, it does not boot (the leds indicate that the chipset initialisation (the first step) does not pass).
If I just load biios default, the leds indicates that it fails when checking the memory (second step of boot). I suspect that it's a problem of memory (but my memory was working well before !): it's 2x512 of DDR 400.
Any suggestion is appreciated :D . I spent several hours trying to configure the bios but it does not boot..
(I'll also try to find help on AMD forums...)
(Some extra info: my PSU is 26A for 12V, so it seems that it's not due to the PSU (as I read in the FAQ of this forum).
Thanks,
Ptitmain.

AMD Geode™ NX Processor Family & DB1500 Development Board
Powerful Software Development Capability for AMD Geode™ NX Processors
The AMD Geode™ NX processor family consists of three versatile and powerful products - the AMD Geode™ NX 1250@6W* processor, the AMD Geode™ NX 1500@6W processor** and the AMD Geode™ NX 1750@14W processor.***
The AMD Geode™ NX processor family leverages advanced architecture to provide powerful solutions for a variety of Internet edge, peripheral applications, and more. The AMD Geode™ NX processor family provides the highest x86 performance for fanless operations.
The NX processor family leverages Mobile AMD Athlon™ processor technology to deliver superior computing power for a variety of thin-client and other applications including point-of-sale terminals, kiosks, high-end printers and home media systems.
Key features include:
* Low-power consumption
* Advanced 7th generation core
* Long-term manufacturing and support
* 128KB level 1 cache
The AMD Geode™ NX processor family is supported by existing low-cost infrastructure, proven architecture and a long-term supply commitment.
The Geode NX 1250@6W processor is based on an AMD Athlon™ core and demonstrates the company’s commitment to making enhancements to its x86 product offerings and delivering a full line of x86 products to market. The AMD Geode family of embedded solutions is part of AMD’s strategy to offer assets, resources and vision for extending x86 solutions from low-power embedded solutions up through the highest-performing server platforms. The Geode NX 1250@6W processor is a cost-effective solution for customers requiring sub-one gigahertz performance without a fan. Operating without a fan not only reduces design costs and allows for better power management, but also allows the processor to co-exist in virtually any environment because it can operate silently.
The AMD Geode NX 1250@6W processor broadens the selection AMD’s customers have for x86 solutions that range from sub-one watt to 14 watts, allowing them to choose a processor that best meets their individual design needs.
.13um fabrication process
128/256KB L1/L2 cache
266MHz Front-Side Bus
Floating Point logic
AMD PowerNow!™ technology
Less than 6 watt maybe i should replace my PSU with battery (typical) to 9 watt (maximum) Total System Power Dissipation
Socket A compatibility
3DNow!™, MMX™ and SSE Instruction Set

Fsbtodb macro in ufs_fs.h does not return correct disk address

I'm using fsbtodb to translate the file inode block address to file system block address.
What I've observed is fsbtodb returns corretct disk address for all the files if file system size < 1 TB.
But, if ufs file system size is greater than 1 TB then for some files, the macro fsbtodb does not return correct value, it returns -ve value
Is this a known issue and is this been resolved in new versions
Thanks in advance,
dhd

returns corretct disk address for all the files if file system size < 1 TB.and
if ufs file system size is greater than 1 TB then for some files, the macro fsbtodb does not return correct value, it returns -ve valueI seem to (very) vaguely recall that you shouldn't be surprised at this example of a functional filesize limitation.
Solaris 9 was first shipped in May 2002 and though it was the first release of that OS to have extended file attributes I do not think the developers had intended the OS to use raw filesystems larger than 1TB natively.
That operating environment is just too old to do exactly as you hope.
Perhaps others can describe this at greater length.

Desktop apps: Report Builder 3.0 (x86) that does not let me allow query result which I created Customers Report. Here is the error message returns.:

Desktop apps: Report Builder 3.0 (x86) that does not let me allow query result which I created Customers Report. Here is the error message returns as following.
Database query from: AdventureWorks2014
System.Web.Services.Protocols.SoapException: The permissions granted to user 'SQLServer2014\Mubs' are insufficient for performing this operation. ---> Microsoft.ReportingServices.Diagnostics.Utilities.AccessDeniedException: The permissions granted to
user 'mujb-HP\mujb' are insufficient for performing this operation.
at Microsoft.ReportingServices.Library.ReportingService2010Impl.CreateReportEditSession(String Report, String Parent, Byte[] Definition, String& EditSessionID, Warning[]& Warnings)
at Microsoft.ReportingServices.WebServer.ReportingService2010.CreateReportEditSession(String Report, String Parent, Byte[] Definition, String& EditSessionID, Warning[]& Warnings)
The permissions granted to user 'mujb-HP\mujb' are insufficient for performing this operation.
Is there anybody help me out, pl
My MSSQL Server express 2014 edition x64 and My desktop "Report Builder (RB) 3.0' is 32bit (x86).
Does Report Builder x64 exist? I didn't see anywhere so I downloaded x86 RB

Hi mujb,
Per my understanding you are using the report builder 3.0 to design the report and when you click the query designer button to execute the query you got the error message above, right?
I have tested on my local envornment and your issue can be caused by the user "SQLServer2014\Mubs" and "mujb-HP\mujb" haven't grant permission to the report server or the shared dataeource/dataset if you have used this.
I would like to confirm if you have assigned both the Item-Level and System-Level role of the user above to sucessfully access the report server, If you haven't grant any access to the above user and when you connect to the report server in the report builder,
you may got the error message:
More details information below for your reference:
Please execute the query in the microsoft SQL Server Management Studio to see if you have permission to execute the query.
If the query works fine in step1, please run the report builder as Administrator and if you are using the shared datasource/dataset the issue can be cause by the you haven't grant access the share datasource, Double click to open the Datasource
and click the "Test Connection" as below to test if it can connect successfully:
If the "Test Connection" failed, please click the shared datasource/dataset on Report Server to check if you have grant correct permission.
Related information about the grant permission to report server for your reference:
https://msdn.microsoft.com/en-us/library/ms156034.aspx
http://www.allenkinsel.com/archive/2013/01/adventures-in-ssrs/
If your issue still exists, please try to provide more details information.
Regards,
Vicky Liu
Vicky Liu
TechNet Community Support

TS1367 I was having a problem down loading photos, so I force quite all programs. Then there was problem launching finder. Relaunched and turned computer off to reboot. Now computer starts, but does not boot up I am stopped at a white blank screen

I was having a problem down loading photos, so I force quite all programs. Then there was problem launching finder. Relaunched and turned computer off to reboot. Now computer starts, but does not boot up I am stopped at a white blank screen

Welcome to Apple Discussions Dathanb
You have posted in the Feedback About New Discussions forum.
As you are a first time poster, you seem to have missed the text at the top of this forum that says:
Please Read This Before Posting Here
If your question concerns a hardware or software technical issue, please do not post in this forum
Go to the main Apple Discussions page, select an appropriate product category and follow the links until you reach the correct forum for your post, then click the POST NEW TOPIC link. Because your post doesn't indicate was OS you are using on your iMac, I can't give you a link to the most appropriate forum.
Basically, though, the version of TechTool on the AppleCare disks is not compatible with newer versions of OS X and/or Macs (I can't remember which). If you don't get a satisfactory response by posting in the appropriate iMac or OS X forum, I suggest you take your iMac to the geniuses at the Apple Store. You can set up an appointment time for the same day online before you leave home.
Peggy

V210 alom starts up; status is alright but system does not boot

I have a series of v210s, all running solaris 9.
After a power down on of the systems powers on alright. showenvironemnt
shows
r4n8mgt> showenvironment
=============== Environmental Status ===============
System Temperatures (Temperatures in Celsius):
Sensor Status Temp LowHard LowSoft LowWarn HighWarn HighSoft HighHard
MB.P0.T_CORE OK 51 -- -- -- 110 115 118
MB.P1.T_CORE OK 60 -- -- -- 110 115 118
MB.T_ENC OK 15 -6 -3 5 40 48 51
Front Status Panel:
Keyswitch position: NORMAL
System Indicator Status:
MB.LOCATE MB.SERVICE MB.ACT
OFF OFF OFF
System Disks:
Disk Status Service OK2RM
HDD0 OK OFF OFF
HDD1 OK OFF OFF
Fans (Speeds Revolution Per Minute):
Sensor Status Speed Warn Low
F0.RS OK 7336 -- 1000
F1.RS OK 7180 -- 1000
F2.RS OK 7180 -- 1000
F3.RS OK 7336 -- 1000
MB.P0.F0.RS OK 17307 2000 2000
MB.P0.F1.RS OK 17763 2000 2000
MB.P1.F0.RS OK 17307 2000 2000
MB.P1.F1.RS OK 17307 2000 2000
Voltage sensors (in Volts):
Sensor Status Voltage LowSoft LowWarn HighWarn HighSoft
MB.P0.V_CORE OK 1.44 -- 1.26 1.54 --
MB.P1.V_CORE OK 1.50 -- 1.26 1.54 --
MB.V_VTT OK 1.28 -- 1.17 1.43 --
MB.V_GBE_+2V5 OK 2.50 -- 2.25 2.75 --
MB.V_GBE_CORE OK 1.20 -- 1.08 1.32 --
MB.V_VCCTM OK 2.55 -- 2.25 2.75 --
MB.V_+2V5 OK 2.58 -- 2.34 2.86 --
MB.V_+1V5 OK 1.51 -- 1.35 1.65 --
MB.BAT.V_BAT OK 2.90 -- 2.70 -- --
Power Supply Indicators:
Supply Active Service OK-to-Remove
PS0 ON OFF OFF
Power Supplies:
Supply Status Underspeed Overtemp Overvolt Undervolt Overcurrent
PS0 OK OFF OFF OFF OFF OFF
Current sensors:
Sensor Status
MB.FF_SCSI OK
r4n8mgt>
However the system does not boot, or show any diiagnositics.
I connected a serial to the "serial management port" but all i get is
C Alert: SC System booted.
SC Alert: Host System has Reset
[SC Status 7fff - OK] Enter #. to return to ALOM.
Copyright 2004 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
Sun(tm) Advanced Lights Out Manager 1.5.2 (m1104)
Please login: admin
Please Enter password: ********
r4n8mgt> console -f
Enter #. to return to ALOM.
Here it sits and does nothing.
Any idea?
Lydia

That sounds like a failed logic board or display module on the logic board...either way you need to take it to an Apple store genius bar and have the techs test it to see exactly what has failed. The testing is free so give the techs a chance at diagnosing the problem.

Animated Gif Image does not render correctly on screen

I have added animated gif image to the scene it does not render correctely.it shakes on the screen. plz give me any suggestion
i use following code
Image logo= new Image(getClass().getResourceAsStream("images/image.gif"));
logoLabel.setGraphic(new ImageView(logo));

Hello user,
I think gif are rendered smoothly.
Are you sure you are not making many object of same images everytime?
Thanks.
Narayan

REPORT DOES NOT RUN CORRECTLY , URGENT PLEASE HELP

Hi,
I am trying to run a report from visul basic screen, but it does not run correctly. Here is how I am running the report. There is a screen developed in VB This screen prompts the user for user id and password. Once it gets that, it connects to the oracle database and pulls out a column from a table. And passes that value as a parameter to the report. Now I am calling the the report for each individual value . There are 21 value being pulled out of the database and it invokes the report 21 times. So there are 21 report engines gets started. Is there a better way to do that ? Secondly when I pass the parameter , some parameters does not pass correctly I guess , because its not generating any out put . Like out of 21 may be 10 or 11 reports gets generated correctly but rest of the reports are blank. I debug the screen i saw that the parameter value is correct, everything seems good. But still the reports are comming blank. Any Idea why it is so ? The command line that i am using in VB screen is
Shell "C:\progra~1\ora95_2\bin\rwrun60.exe P:\Business_Analysis_&_Reporting_Tool\Test_REPORT_Templates\STORE_TYPES\Baby_Distribution_Report.Rdf USERID=" & UID & "/" & PWD & "@cposp201 DESFORMAT=PDF DESTYPE=FILE DESNAME=" & txtPath.Text & Replace(strName, " ", "_") & ".PDF BRND='" & adoRecBrand!Brand & "' PRINTJOB=NO PARAMFORM=NO"
In the above command " adoRecBrand!Brand " is the parameter thats being passed. This is actually a recordset and brand is the column in it. When I debug the screen , I see the value also there. But the report comes out blank. Please help. This is urgent.
Thanks
Feroz

The way you call reports is not scalable. If you have 100 records come back from database, you would end up launch 100 engines at the same times, which probably will blow up your machine. You should use oracle reports server to do that. You can either use rwcli60 to submit the job to reports server, or invoke rwcgi60 from URL.
I am afraid some of reports engine failed to start and you get nothing back in your case.
After switch to use reports server achitecture, if you still see some report is blank in your application, then you can run that report with that special set of parameters manually and see if any problem with the report itself.
Hope this helps.
Thanks,
-Shaun

New MBP i5 does not boot after hard disk swap

Hi there,
I received my new i5 MBP today. After booting it once with the installed HDD to check if it's ok, I exchanged the hard disk for the one in my Late 2008 Macbook Pro. After doing this, my Late 2008 Macbook Pro boots fine with the (new) hard disk from the new i5 MBP, but the i5 MBP does not boot with my old hard disk.
To give you some details:
- I have installed 10.6.3 on the (old) hard disk that's not booting.
- The i5 MBP boots fine from the installation DVD
- Disk utility finds and can read my hard disk, no errors
- PRAM NVRAM reset did not help
- when booting in safe mode, I can see the system stop booting after or while loading Extensions.mkext
My guess is, it tries to boot and load the wrong Extensions for the new system (CPU? GPU?). I have no idea how to fix this.
Any help would be greatly appreciated!

Focx,
Welcome to Apple Discussions.
Inserting the drive from an earlier model MBP will probably not work. The version of the system you have on that HD is designed for earlier hardware so when you put in in your new machine it's going to be recognized. What I'd recommend is re-installing the disk that came with the new machine and of course putting the 2008's disk back in the old machine. Then use Migration Assistant on the new machine and migrate your data from the old machine into the new machine.
This will provide a much more stable system and should work just fine.
Regards,
Roger

X86: Solaris does not boot correctly?

Similar Messages

Maybe you are looking for