X99S Gaming 7 error 00

Hello guys this morning I started the PC, and so everything is right, then reboot to change the frequency of the CPU and off instead of rebooting, try turning on your pc ... turn on all the lights of the MB but does not boot and debug diplay shows "00".
What happened?
Bios H8
Cpu 5930k
Ram 32 GB G.Skill 2400
Raid 0 SSD Kingston

Quote from: Svet on 02-May-15, 00:02:30
list full detailed, system specs, see >>Posting Guide<<
Check all connections, especially between power supply and motherboard.

Similar Messages

X99S Gaming 7 - motherboard temp readings in fast boot?

Hi, odd question but does anyone elses motherboard error message display/temp sensor display not display the temperature if MSI fast boot is set in BIOS?

Then try latest BIOS as TZBC suggested
Quote from: TZBC on 07-April-15, 15:36:09
http://www.msi.com/support/mb/X99S-GAMING-7.html#down-bios
If you would prefer DOS way of flashing, you can try to >>Use the MSI HQ Forum USB flasher<<
And latest BETA for your board to be used with Forum Flash Tool:
https://forum-en.msi.com/index.php?topic=183589.msg1324203#msg1324203
Sometimes BETA BIOS fixes the issues that are not released yet officially.

Msi x99 gaming 9 ack problems

ok got my new msi x99 gaming 9 ack with i7 5930k and g.skill 2400 ram
got my corsair ax1200i
so my problems i have been working on this all night near enough but today we have progress.
so problem is when i put ram in slot 1 would not post debug 04/55/60 no keyboard or signal to monitor. so i have finally got it working and got into the bios by put just one stick in slot 5. tried all 4 sticks in slot 5 but one failed at 6f so i think now one stick is faulty. but back to main problem with slot one.
once i had it booting up i switched off system and added 1 stick in slot one.
and it would not post debug 04/55/60.
so do i ram it or do you think bios update will fix this problem thanks in advance

Last night the exact same problem occurred to my Gaming 9 ACK.
Board worked flawlessly for three months with a 5960X processor, quad channel G.Skill 3.33 memory ( 16gb- 4x4 ) and four msi GTX980 gaming in quad sli mode.
Turned off the pc last night, and today, upon start the pc did not boot.
04-55-60-04 and all over again.
Memory modules are populated in slots 1-3-5-7. After several try and error efforts, slot 7 is blocking the system from booting. All four modules checked and are fine.
Removed module in slot 7 and booted. No problem there.
After entering windows 7 environment, a second even bigger surprise surfaced.
NO SLI. Device manager sees only gtx980 in slot 1 and nothing else.
New tests.
Only pci-e slot 1 works. All others are non functional.
So I am with an 8000$ pc, which works with 12gb triple channel memory and one VGA.
Obviously motherboard has gone south.
What now ???

MSI X99S Gaming 7 and debug code 67

Hi,
I have MSI X99S Gaming 7 motherboard, Crucial 2x8GB 2133 DDR4, MSI GTX970 Gaming 4G, Corsair RM650, i7-5820k setup.
When I am trying to boot the machine it always stops and the debug led shows code 67. I have tried to take everything out, reseated processor and to boot with just the minimum set of components. Result is always the same code 67.
I am running out of ideas. Do you have any hints or should I just return the mobo and processor?
Best Regards,
juha

Quote from: shadow85 on 22-December-14, 19:40:31
So are you going to RMA the board or just use it with 2 sticks? Thats means you are not planning on using it in quad channel, would be a waste.
Anyways if I were you I would definatly RMA it asap. This error 67 problem people are having seems to be widespread. MSI really need to look into this.
As has been said previously, contact MSI. Should they look into it? Yes, but the moderators here are not MSI employees, and while we can bring issues to their attention, we cannot make them look into problems.
So if you have this problem, please contact MSI directly: >>How to contact MSI.<<

Problem with JPWR2 on a X99S GAMING 7

Hi,
Currently I have a problem with JPWR2 on a X99S GAMING 7 Motherboard. When I plug a 6 pin or a 8 pin on the JWPR2 the motherboard crash and the cable overheat or short-circuit. My power supply is a 1000W SIlent pro bronze. I tested with a new cable on another port on the power supply but it doesn’t work. I tested with without CPU too but still the same problem.
Can someone help me ?

you are using the Cooler master 1000W silent pro bronze right?
Normally the power supply should have 4 pin or 8 pin, the 6pin/8pin is normally for the VGA card and not for the Motherboard.
Please double check again and use the 4 pin or 8 pin for the MB.

X99S GAMING 9 AC Not booting - Debug 94 code - Issue with GTX 980 SLI in WoW

Hello, I bought the X99S GAMING 9 AC motherboard but have ran into some issues.
The computer won't boot when I put my second MSI GTX 980 Gaming 4 GB card in the last PCEI 3.0 port (PCIE port 5) and I get the debug LED message 94 on the motherboard. I have a SLI setup.
The first card I have in the second PCIE 3.0 port due to the Noctua U14S CPU fan takes up space for the first slot. So I have been running my grafic cards in PCIE slot 2 and 4 with some issues.
First the card in slot 2 gets really warm over 86 celsius. And second: SLI runs really poorly in World of Warcraft. I get a lot higher performance with just one card activated. I am not sure if it's cause I am not running my cards in the recommended PCIE 3.0 ports or because WoW has some issues with SLI, but I heard other people have no issues at all with WoW in SLI.
I got the same issue with 3Dmark firestrike, the cards perform really poor in SLI. I get higher score with SLI turned off..
Though SLI seems to run pretty well in 3dmark 11 and Diablo 3 Reaper of Souls.
But the main issue right now, is that the computer won't boot with the grafic cards in PCIE port 2 and 5. The solution to run them next to each other is not good, cause it gets really hot and I get bad performance in WoW and Firestrike.
Picture of my setup before I switched places with the grafic cards as you can see, it is really tight:
Any upcoming bios updates (got v1.3) that will solve this issue on the horization? Hopefully this get sorted out really soon..
My whole computer setup:
Intel i7 5820K | MSI X99S Gaming 9 AC (bios 1.3) | SLI MSI GTX 980 Gaming 4GB | Samsung 850 Pro 512 GB | WD Red 4TB | G.Skill Ripjaws DDR4 3000MHz 4x4GB | EVGA SuperNOVA P2 1000W | Noctua NH-U14S PnP | Fractal Design Define XL R2 | 5 Noctua NF-A14 PWM 140mm fans | Windows 7 Pro 64 bit

You must use the recommended PCIE slots as the manual says for your CPU type, PCIE #1 and PCIE #4 if I remember, just open the manual :P for optimal 2Way SLI, also your 5820k will limit to 28 pcie lanes only if you plan to add more vgas...the other problem is your giant CPU air cooler blocking PCIE#1, do a favor to yourself, buy a watercooler for your 5820k and your problems are gone, add some overclock in your system, low noise and better temps.
Here I use 3x980 in SLI with X99S Gaming 9 AC, going soon to WC the VGAs with EK blocks.....3way is far more temperature critical than 2way spaced one.
Cheers

MOVED: MSI x99s Gaming 7 problem

This topic has been moved to GAMING Motherboards.
https://forum-en.msi.com/index.php?topic=184649.0

There should be some guides in the manual...
http://www.msi.com/support/mb/X99S-GAMING-7.html#down-manual

X99S Gaming 7 Literally can't install the OS

MOBO: X99S Gaming 7
CPU: i7-5820k
RAM: 8gb 2x4gb sticks
SSD: Samsung Evo 850 m2
GPU: GTX 770
I'm at my wits end, I can't for the life of me get Windows installed to this machine. I've gotten to the drive chooser for the the Windows installer, but the one time it recognized the drive, it told me it wasn't partitioned correctly and couldn't install.
I'm seriously not sure if it's the mobo or the drive. Any suggestions?
Tried Windows 7/8/8.1/Ubuntu, nothing.

You can simply press the button next to the PS/2 and USB 2.0 ports with the power cord unplugged. Or best way to clear cmos is by taking out the battery (around PCI-E_1 and 3) for more than 5 sec and then put it back, also with the power cord unplugged.
Basically like this:

X99 Gaming 7 RAM DIMM3 and DIMM4 not working

I recently purchased an Intel 5930k which required me to also get an X99 motherboard and DDR 4 RAM. I had to RMA the board because it wouldn't recognize RAM (which worked in other DIMM slots) in DIMM 3 and DIMM4. I found it kind of odd because that means that essentially the board was not responding to channel 3 of my CPU. When I removed the CPU for the RMA, I did not see any bent pins in either the CPU or the LGA 2011-3 socket. I updated the Bios to the release from 2014-11-06.
Here is my list. What do you think I should do while waiting for my new board? A lot of people seem to be having issues with RAM not being identified in this board. I'm worried I'll get the new board and take the hours to set it up again only to find that the BIOS do not support this setup.
X99 Gaming 7
Intel i7 5930k
Crucial Ballistix Sport 16GB Kit (4GBx4) DDR4 2400
Corsair H100i water cooler
Gigabyte GTX 970 G1
Coolmax 700 W PSU
Carbide 300R Windowed Case

I received the replacement motherboard, and it was able to read RAM in all 4 channels. After inserting each chip, I booted to ensure that it was recognized. I did my best to boot when adding new components to make sure that they were put in properly. I'm very happy that this board works and would recommend it to others. My takeaway is that sometimes you lose the lottery and get a bad component.

MSI X99S Gaming 7 Won't Boot

Hi -
I just recently purchased an X99S motherboard. I put it all together, and all was fine for about 24 hours. I updated the BIOS and then started running a defrag and left the machine on while I went to work. When I got home, the machine was off. It's not responding to the power button the board or on my case. If I turn the power off on my PSU and turn it back on and hit the power switch, I get a split second flash of lights and then nothing. I initially thought that it was my power supply so I bought a new one. I got that installed and same thing. One thing to note is that the MSI LED up by the 24 pin connector is on red. I've already tried the secondary BIOS and I have removed all of the memory except the DIMM in Slot 7. I haven't yet tried to remove the board from the case yet and tried it on a non conductive surface. I just wanted to get some thoughts on that debug LED that is currently on. I believe the motherboard has just died, but wanted to run it by someone first.
Here are my specs:
Board: MSI X99S Gaming 7
Bios: Version 14.7
VGA: MSI GTX980 Gaming
PSU: EVGA 1000 Watt G2
CPU: Intel Core i7-5930K 3.5GHz
MEM: Corsair Vengeance 2666 4x4gb CMK16GX4M4A2666C16
HDD: PNY 256GB SSD
COOLER: Corsair CWCH60 Water Cooler
OC: None
OS: Windows 8.1 64bit

Take it out of the case, place on non conductive surface (wooden table, motherboard box) and run it then. Also try with single RAM stick in every RAM slot.
Try clearing CMOS >>Clear CMOS Guide<<
Also make sure all power connectors are properly fitted in.
What way did you update the BIOS? Also was it successful?

Problem with X99S GAMING 9 AC - PCIE-PORT reporting V1.1 same with SLI

Yeah as the topic is saying, I got issue with my PCIE 3.0 ports, they are saying my grafic cards are running at x8 1.1
I should first mention that I had these issues for a while, and I also updated all drivers to the latest versions, but still same issues. I got the 1,4 bios version for the motherboard and the nvidia V344.65 that was released today.
I tried to change it in bios from auto to gen 3 on the PCIE-ports, but still same results.
I made a post earlier about that SLI running slow in WoW and 3Dmark Firestrike. Maybe this is the source to the issue due to the ports running at 1.1 and not 3.0?
Also, in both WoW and 3Dmark Firestrike, I get much higher FPS and results with just one grafic card activated, when I go into SLI the results drop like a rock..
The weird thing about SLI though, that it seems to work okay in games like Diablo 3 ROS and 3Dmark11.
I have my grafic cards in the recommended PCIE-ports, 1 and 4.
Here is a screenshot how it looks like in GPU-z:
Is this a known issue and is there any upcoming fix to this? Feels really bad I can't use my grafic cards to their fullest potential..
My whole computer setup:
Intel i7 5820K | MSI X99S Gaming 9 AC (bios 1.3) | SLI MSI GTX 980 Gaming 4GB | Samsung 850 Pro 512 GB | WD Red 4TB | G.Skill Ripjaws DDR4 3000MHz 4x4GB | EVGA SuperNOVA P2 1000W | Noctua NH-U14S PnP | Fractal Design Define XL R2 | 5 Noctua NF-A14 PWM 140mm fans | Windows 7 Pro 64 bit

Quote from: Svet on 12-November-14, 23:58:15
its probably because the render test doesn't handle or don't support SLI well and second card become back to idle
run something else apps., bench or games who support SLI well then check their modes
Enable sli load balancing if needs from nvidia control panel to check SLI utilization
Seems to work the correct way when I start a game, but still got issues with WoW and 3Dmark firestrike. My results with SLI is far worse then with just one single card activated. Anyone know why?
I get more FPS from WoW with one card then two, and I get much higher score in 3Dmark firestrike with just one card..

MSI X99S GAMING 7 - slow booting; HDD aren´t recognized in BIOS

Hi,
i´m facing a similar Problem as it is described in "MSI X99A Gaming 7 and Samsung SM951 PCI-e very slow boot time" https://forum-en.msi.com/index.php?topic=255919.0
My rig:
- i7 5930k
- X99S Gaming 7 (BIOS h90)
- PALIT GTX 980 Super Jetstream
- OCZ revodrive 3 x2 240 GByte (System disk)
- Corsair Force 3 120 GByte (game disk)
- 2x SAMSUNG HD501LJ 500 GByte (SATA 3GB/s)
- 1 LG Electronics BH16NS40
- 16 GByte Corsair Vengeance LPX schwarz DIMM Kit 16GB, DDR4-2666, CL15-17-17-35 (CMK16GX4M4A2666C15)
- 1000W power supply
- ANTEC P193 case
- G19 Keyboard
- MX518 Mouse.
I assembled it yesterday and during the first booting sequence it restarted 3 times.
After that it took 5 minutes to be on the Windows Desktop. Furthermore I recognized that all the HDDs and the optical drive weren´t available.
I tried to activate them in the Windows System - with no result. Than I checked the BIOS, they weren´t present there.
At the end i checked the HDDs only with the power supply, they booted. As soon as I connect them with the SATA cable they stand still - no spin up hear-able.
Now The BluRay and the HDDs are disconnected, the booting sequence is a Little bit faster (still 3 minutes).
In the BIOS I only activated the XMP-Profile für the RAM and I changed the booting sequence for the REVODRIVE.
May someone has any hint for me, how to deal with this Problem - but as I stated at the very beginning: it sounds similar to me.
Best regards from Austria
Gerald
P.S.: I apologize for "hijacking" - I tried to simplify the Forum by merging similar issues.

Your explanation isn't very helpful.
Your third try you got the Revodrive, corsair, and optical running? Meaning that you could boot multiple times and have it all work correctly?
I hate saying it, but if you aren't going to be descriptive, we aren't going to be very much help.
For what it's worth, I'm starting to think that the Revodrive and the motherboard do not work well together.
Personally, I would also consider contacting MSI directly about the issue. They might be able to issue a new BIOS that improves compatibility.
>>How to contact MSI.<<

MSI x99s Gaming 7 problem

Hey guys, 1st time PC builder having one minor problem. I don't know where to plug in my case's power sw, reset sw, HDD led, power led+, and power led- connectors. Everything else was pretty easy except these ones. Any help would be greatly appreciated.

There should be some guides in the manual...
http://www.msi.com/support/mb/X99S-GAMING-7.html#down-manual

Msi x99 gaming 9 ack does not detect capture card when using with xsplit

msi x99 gaming 9 ack does not detect capture card when using with xsplit
i install every but still it does not work.

Hi
It wasn't hard to find your motherboard version:
http://www.msi.com/support/mb/Z68AGD80_B3.html#down-bios
Since your BIOS is v20.1, it couldn't be G3
Apart from checking BIOS, you can only check motherboard or moth...

How to Flash MSI bios - x99s gaming 7

using live update through windows - big NO NO as far as i understand.
downloading the Bios update file from MSI site - http://www.msi.com/support/mb/X99S-GAMING-7.html#down-bios
unpacking it and trying to run from dos mode from within windows (/CMD) - doesn't work.
it says not compatible with system (Probebly the 64bit windows).
trying through BIOS, M-flash, asks to be pointed to a USB key.
i tried extracting the BIOS update package from (http://www.msi.com/support/mb/X99S-GAMING-7.html#down-bios) to the USB key.
then back to bios, M-flash, pointed out to the USB key, chose the BIOS file "*.H40"- but then it says i don't have a file named - "ME" something.
so... how exactly one suppose to flash the bios ?
cheers.

Quote from: flobelix on 17-October-14, 22:19:50
You are now on thin ice vmanuelgm. This thread is not your personel "vmanuelgm is correct" thread but a tech support thread and support for the OP (not you) is offered.
The forum method is the safest way there is and also safer than MFlash that will at least only update ME as well if that is manually selected what is not required using the provided archive. I will not discuss with you about experience in flashing but you should maybe consider that I have quite some knowledge in that regard.
Secondly you were not partially but fully wrong as you didn't say h42 is there but you said h42 would be the latest. Anyway nobody asked for a beta so OP can consider it if he is not happy with the latest official as this is no beta thread like I also already said.
If this will continue off-topic in any way I will clean sweep this thread from reply #4 on.
You should contact MSI to post your MSI HQ as first flash option in manuals, and getting it burned in DVD roms along with mobos...
Until then, MSI official flash methods are what you know, and MSI HQ is not between them...
I am not on any ice, not posting anymore here, with such genious and democratic moderators...
Bye...

MSI x99 Gaming 7 Debug code 04

hi this day my computer dont start only black screen , i see mobo debug code 04
msi x99 gaming 7 service manuel say 04 code = Power on South Bridge Initialization
i use 2. bios swich computer working no problem
now i go RMA?
edit: me try bios clear button nothing always full black screen and debug code 04 , i cant remove bios battery 2 graphic card + water cooling :/

If you familiar with flashing bios, you can try use the second bios to recover the first one.
Manuel has some guide...
BIOS recovery with AFUDOS command
When BIOS updating fails or causes the computer non-bootable, you can recover the
failed BIOS by the steps below.
Preparation:
1. Prepare a bootable USB flash drive.
2. Download the latest BIOS file from the MSI official website at www.msi.com, and
then decompress the file.
3. Copy the AFUDE238.exe and the BIOS file to the bootable USB flash drive
BIOS recovery steps:
1. Power off the computer.
2. Set the Multi-BIOS switch to the functional BIOS ROM.
3. Insert the bootable USB flash drive you have made to the USB port.
4. Boot the computer into the bootable USB flash drive.
5. Set the Multi-BIOS switch to the failed BIOS ROM.
6. Execute the below command to flash the BIOS:
For example: AFUDE238 EXXXXIMS.XXX
7. Restart the computer after the BIOS flashing is complete.
Important
Do not use the Multi-BIOS switch when system is booting up.

X99S Gaming 7 error 00

Similar Messages

Maybe you are looking for