X99S Gaming 9 ACK - power supply compatibility - JPWR2 and JPWR3- Status code 00

Hello,
Setting up a newly purchased X99S Gaming 9 ACK, and would appreciate any help. Can't get past status code 00 and am in debug mode.
First step in my debug process, I'm trying to confirm power supply requirements. The board has two 12V input connectors - JPWR2 and JPWR3. The manual mentions them both. However, my power supply only has one 12V "EPS12V" cable with an 8 pin connector that can be separated into 4+4.
A quick search did not turn up any power supplies that come stock with two 12V cables. This seemed odd, so I searched for information for JPWR2 and JPWR3 hoping to find something and what turned up was somewhat contradictory. Some info out there seems to suggest that powering one of the two would be OK if not overclocking. So I tried that - first just JPWR3, then split the power connector and did just JPWR2, then did JPWR2 and part of JPWR3....and then just to confirm what I thought I was seeing (that 00 status is telling me the CPU's not active) I removed everything from both JPWR2 and JPWR3. In all cases, the status code was 00.
So I'm looking to find out how folks with this MB actually working have connected the power.
Question 1: Does anyone run it without having both JPWR2 and JPWR3 connected? If so, what approach do you use?
Question 2: Does anyone run it having them both connected? If so, please let me know what power supply you use. I am guessing maybe a configurable cable sort could be set up with two 12V lines?
I know, it's possible with no known-good components (well, the power supply is freshly removed from a happily functioning PC, so it's not suspect) I may have either a bad CPU or a bad MB. And they are both brand new and eminently returnable. But I don't want to do that till I know I've got them powered correctly. I'm relatively confident (well, hopeful) that having the correct power supply setup will let me get past 00 status code and see what else I get to debug.
Thanks in advance for any and all help.

Thanks for the input. Reset CMOS, removed all but the first stick of RAM. No change. Status code 00.
Initial PS was the Corsair TX750W. I got another power supply to test that has cables to fill both JPWR2 and JPWR3. No change. Status code 00.
So, apparently a DOA Motherboard. Was afraid of that. Sending it back to try again.

Similar Messages

X99S Gaming 9 ACK Power Supply Type/Reqs

The motherboard appears to want, for cpu connection, one 8-pin connector (JWPR2) and one 4-pin connector (JWPR3). I've got a new Thermaltake DPS-G 1050 power supply, but it has only the 8-pin CPU connector on it. In fact, none of my power supplies for my other machines have both of those types of CPU connectors.
Is it correct that the motherboard needs both the 8-pin and the 4-pin CPU connectors? And if so, which brand and make of power supply will work with this motherboard?
Thanks folks!

Hi,
No. The motherboard only needs 24 pin connector and one 8 pin connector. Additional 4 pin is for extreme overclocking. My Z97Mpower Max Ac has 8 and 4 pin CPU connectors but I only use 8 pin as I am not overclocking. For medium overclocking also 8 pin is enough.

18.5v and 19.5v power supply compatability, nc4200

Hi,
I have an nc4200 laptop that needs a new power supply. I chatted with a HP consultant and he said I could use one of the new 90W slim smart adaptors for this, but that has 19.5V output (whereas the original 65W adaptor was 18.5V). The smart adaptors "Say" they are backwards compatible with all HP business notebooks. How important is it to match up the voltages? Can the laptop compensate for +-1 volt differences? Thanks!
This question was solved.
View Solution.

Hi,
For voltage, + or - 5%-7% is ok, for wattage 90W is much better than 65W. Should be ok to use new charger.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

WS-C4003 power supply compatibility

Hi,
I've a WS-C4003 with one WS-C4008 power supply. I've released a Sony APS-111 (CISCO P/N: 34-0873-01) power supply from an old WS-C4006 and i'd like to know if it's compatible with the WS-C4003. It seems that it'll work but I don't find any compatibility document to guarantee it.
Thanks in advance!

Based on five minutes of research, that power supply has a standard ATX form factor and plugs. Ergo, any generic power supply that is ATX will work. In example:
Corsair - 650W ATX CPU Power Supply $84.99
Dynex™ - 400-Watt ATX CPU Power Supply $49.99
I am a Bestbuy employee who volunteers on these boards on my own time. I am not paid for posting here, and you should understand that my opinions are exactly that - opinions. I do not represent Bestbuy in any way.
: Open Mailbox

IMac G5 bluetooth + airport + power supply problems - oh and the dvd drive

Yeah, seems like a lot is going wrong with my mac lately. I bought the iMac G5(no isight) model last year around july. I had some power issues (i.e. leaving the house with it turned on to come home and find it off) For the last year though that was all that was wrong. Once I had to reinstall OS X because it would not find the OS X harddrive during one of these power losses, but that was it.
Then about two weeks ago, I came home to a turned off iMac. I thought the power had gone out in my apartment, but the clocks were all right, and to my surprise the iMac would not turned on. Because I am not under warranty I searched online and found an extended exchange program for my emc model. (http://www.apple.com/support/imac/powersupply/repairextension/) I made an appt at the apple store and they replaced the power supply.
I got the machine back two nights ago and my bluetooth hardware wasn't recognized. And I now had a new "ink" system preference panel in the hardware section which aparently is some sort of handwriting recognition tablet. It ticked me off, but I just wanted to use my computer.
Well today I came home from work and my computer was acting funny. Everywhere I clicked brought up dashboard. This had never happened before and I had no choice but to force a shutdown. Powered it back up and poof, there goes my airport card. No hardware recognized. Now I have a 25 ft cable running the floor of my apartment. This was cause enough to call apple. I was told to make another apointment to bring the computer in. The guy made it sound like it was no big deal to lug a 30 lb bulky computer 40 miles and through a crowded mall. He also made no promises that the repairs would be covered under the exchange program.
I just wanted to hear any suggestions before I decide whether or not its worth it to bring in the computer. Nothing shows up in system profiler under bluetooth or airport. Should I just lie to the "genius" and tell them that my computer still shuts down randomly? I think that way they would at least replace the logic board (which I think is the problem) before telling me to sell my kidney and pay for repairs. I've tried reseting the SMU, and I looked at the bluetooth and airport cards to see if they had been accidently disconnected during the PS replacement. They are actually screwed into the logic board so I think their connections are efficient.
Oh and about the DVD drive. I have to use two cd's in order to burn a single disc. The first disc I put in the drive NEVER works. It spins for about 30 seconds then starts buzzing like blender and spits the cd back out. The second blank disc I put in USUALLY works, but sometimes it takes three discs. This problem has always been there since day 1, but I don't burn enough cd's for it to be an issue.
Thank you for listening to my gripes. I really don't think I'll make the mistake of buying the first issue of a model.
iBook G4 900mghz, iMac G5 20" 2.0 ghz Mac OS X (10.4.8)

OK, first thing -to restore your bluetooth, shut down, unplug for a few minutes and then reboot. Thay usually brings the BT back. You should also repair permissions. Reset your SMU nd your PRAM as well.
Try those four things and please post back,
Miriam

HT201263 iphone has completely dead, it wont connect to power supply or PC and won't re charge

My iphone 4 has completely died - it wont connect to the power supply, wont connect to PC nothing - any suggestions ??

Maybe the fact that it's dead has something to do with it...?
If a reset didn't work, make an appointment at the Genius bar and let them look at it.

Power supply compatibility question

I currently have a HP 4250n printer with a broken power supply and an old 4050 HP with a working power supply, I was wondering will the 4250 work with a 4050 power supply in it?
Feedback would be much appreciated.

Which "model" & "generation" G5 iMac do you have?
Need this info so that the knowledgeable users can provide you with the proper troubleshooting solution(s).
http://docs.info.apple.com/article.html?artnum=301724-en How to identify your iMac
http://docs.info.apple.com/article.html?path=Mac/10.4/en/mh355.html Getting information about your computer
You can have this info displayed on the bottom of every post by going to 'My Settings' which is located in the column on the right under your name, and filling in the information asked for.
Thank you

T61 - Power supply wire melting and smoking

Do you guys have any problem with power supply. My wife just called me and she smelled something burning. And power supply wire is melting and smoking.
And I called Lenovo tech and he told me that my machine is just 13-month old and he can't do anything at all.
He just told me replace power supply. I used to have dell and IBM X41 and never have wire burning problem.
Is this normal? If my wife found out little late and buring the carpet still he is going to say this machine is out of warrenty and Lenovo has 0% responsibility.
I told him, I'm going to take picture and post to the internet and he told "I don't care".
Wow what a nice man. He supposed say "Sorry" first then say your machine is out of warrenty...
Anyway, I'll never going to buy Lenovo again.
Thanks
Message Edited by icul4u on 07-10-2008 01:28 PM
Message Edited by icul4u on 07-10-2008 07:13 PM
Solved!
Go to Solution.

icul4u wrote:
I think your computer system has my information.
I don't want to post my personal information here.
Mark didn't ask you to post your contact information in the public forum. He asked you to send him a PM (private message). To do that, click on the little envelope icon at the top of the forum and send the message to Mark_Lenovo Without the information he requested, it will be difficult for him to help you.
I edited your serial number out of your message as it doesn't need to be posted publicly.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Jane
2015 X1 Carbon, ThinkPad Slate, T410s, X301, X200 Tablet, T60p, HP TouchPad, iPad Air 2, iPhone 5S, IdeaTab A2107A, Yoga Tablet, Yoga 3 Pro
I am not a Lenovo Employee.
I AM one of those crazy ThinkPad zealots!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!

I have the first generation Time Capsule A1254, the power supply went south and I'm looking to replace it any suggestions where I might find one? Thanks

Hi,
I have the first generation Time Capsule A1254, the power supply inside went south, does anyone know where I can purchase another?
Thanks

Might be worth considering a repair of the power supply so you can keep the data on your drive.
I have no association with the link below other than as a customer.
http://www.timecapsulerepair.net/

Issue with JRun, PDF's, and HTTP Status Codes

I've been having an issue where, in our production
environment, PDF's report status codes 200, instead of the proper
200 and 206. Our Test/Staging environment have the exact same
setups (hardware, software, patches, etc), but report the proper
single 200 and multiple 206's. I've racked my brain trying to
figure out what's causing the different results between test and
production, but couldn't find anything. I happened upon this JRun4
patch...
http://www.adobe.com/support/documentation/en/jrun/4/releasenotes_4_updater6.html
... which states:
quote:
60181 - Inline PDF downloads are logging 200, instead of 206,
for the partial content portions in the IIS logfiles when the
ColdFusion Wildcard handler and an ISAPI filter is loaded (site or
global level).
... I can't find any reference to this fix for ColdFusion.
When I examine the jrun version of CFMX7.0.1 Updater 2, it reports
JRun4 Updater 5, instead of 6 even though 6 was released long
before CFMX7.0.1. What can I do? Can I apply the jrun4 patch to
CFMX7?

You can only apply the JRun hot fix if you have the
multiserver or j2ee install of CFMX. You cannot apply the patch if
you have the server install.
Ted Zimmerman

OTA Download and HTTP Status Codes

Hi there,
i am planning to check the http status code of an OTA download. Even if I interupt the download process, the server still responds with status 200.
Does anbody have an idea, how to implement this process?
Thanx,
Simone

i have relatively a same question. I am developing an OTA Provisioning platform for Java Games . Herez the flow:
-> End User (Client) requests a content by entering his mobile no. via website
-> Server sends a WAP PUSH (Binary SMS) to his mobile.
-> When User opens the WAP PUSH (SMS), it will connect via GPRS to the server and start retrieving the game ( I am using Servlet to stream the JAD File)
-> Then it will retrieve JAR file (path defined in JAD file)
-> I have defined:
MIDlet-Install-Notify: http://myserver.com/content?323
in JAD File. So after Installation the Mobile handset connects the URL specified. I am then grabbing the status code i.e 900 or 901 ....
Problem:
<b> User Tracking: </b> I am not able to track the user e.g there are number of register users each having unique Id. When they download the content the Midlet-Install-Notify connects to servlet, but i am not able to distinguish among users as i am not able to dynamically assign User ID to MIDlet-Install-Notify URL in JAD File.
I am in now in real trouble. If any one knows the solution how to maintain session or URL rewriting i.e dyanmically assign Parameters to MIDlet-Install-Notify plz share it.
Thanks in advance
Regards
Hamid
[email protected]

OTA and HTTP Status Codes in Motorola T720

Hi,
I am trying to check OTA status code by using T720. I wrote a simple servlet to receive the status code after midlet install, and also set up the MIDlet-Install-Notify attribute to point to the servlet.
T720 works fine in download and install, but doesn't start my midlet and I didn't get the status code.
I truly believe I missed something which is very important in this issue which I really have no clue (servlet code? config? ...)
Can anyone help?
Greatly appreciated!

I am developing an OTA Provisioning platform for Java Games . Herez the flow:
-> End User (Client) requests a content by entering his mobile no. via website
-> Server sends a WAP PUSH (Binary SMS) to his mobile.
-> When User opens the WAP PUSH (SMS), it will connect via GPRS to the server and start retrieving the game ( I am using Servlet to stream the JAD File)
-> Then it will retrieve JAR file (path defined in JAD file)
-> I have defined:
MIDlet-Install-Notify: http://myserver.com/content?323
in JAD File. So after Installation the Mobile handset connects the URL specified. I am then grabbing the status code i.e 900 or 901 ....
Problem:
<b> User Tracking: </b> I am not able to track the user e.g there are number of register users each having unique Id. When they download the content the Midlet-Install-Notify connects to servlet, but i am not able to distinguish among users as i am not able to dynamically assign User ID to MIDlet-Install-Notify URL in JAD File.
I am in now in real trouble. If any one knows the solution how to maintain session or URL rewriting i.e dyanmically assign Parameters to MIDlet-Install-Notify plz help/advice the solution.
Thanks in advance
cheers
Hamid
[email protected]

MDD power supply compatibility

I have a MDD dual 867 G4 tower, which I believe was the first model of the MDDs.
Can I swap in a powersupply from a newer MDD dual 1.25 tower?
I am just wondering so I know for certain that the pin outs and voltage isn't going to fry my motherboard.

Should be fine, but compare the pinouts to the only MDD PSU listed here...
http://www.xlr8yourmac.com/tips/MDD_ps_mods/MDD_PS_Mods.html
Also only one listed on converting ATX PSU for use in an MDD...
http://atxg4.com/mdd.html
(Trying not to just go by my failing memory that tells me they all were the same.)

T440s keyboard and external power supply

The issue that I come across is if T440s starts up on battery, as soon as the external power supply is connected, the keyboard stops responding, as well as mouse. if I disconnect external power supply, both keyboard and mouse function as usual.
If start up on external poewr supply, it seems to be OK.
Any suggestions?

Hello Hans -
Taking a look a the PrecisionHD Camera User Guide on pg 9, the 2.5x camera does have a power supply connector just like the 4x and 12x cameras. It does say the power supply connector is For future use, so it doesn't seem like it supports an external PSU at this time.

Looking to upgrade the video card and power supply in the K330

Hello, I'm looking to upgrade the power supply and video card in the Lenovo IdeaCentre K330 but I need to know if these parts will be accepted by the mobo.
Here's the card name (no link, don't know if theres a restriction to off site links) ASUS 2GB GDDR5 DIGI+ VRM technology Graphics Cards HD7770-2GD5
The power supply name follows: Xion High Performance 1000 Watt ATX Power Supply XON-1000P14F
Thanks for reading, and extra thanks for a good reply

Thanks for replying, I have looked into other PSU's and came up with this: XFX PRO750W Core Edition 80+ Bronze ATX 750 Energy Star Certified Power Supply
Feedback? And main question is, will they both (video card and PSU) be compatible with the motherboard that come standard in the K330?
I don't really have a need for the front panel except the power, and backontrack buttons.
Also, the reason why I'm getting a high wattage PSU is because I might later decide to build my own PC with the upgraded parts, and put the old parts back into the K330

X99S Gaming 9 ACK - power supply compatibility - JPWR2 and JPWR3- Status code 00

Similar Messages

Maybe you are looking for