Xbindkeys -- one combination is not working

Hi guys, recently began to experiment with different DEs/WM. Not to input keybindings every time again decided to use xkeybind. It works, except for one XF86AudioRaiseVolume
This test indicates that this key works
$xbindkeys -k
Press combination of keys or/and click under the window.
You can use one of the two lines after "NoCommand"
in $HOME/.xbindkeysrc to bind a key.
"(Scheme function)"
m:0x0 + c:123
XF86AudioRaiseVolume
Here is my ~/.xbindkeysrc (everythinf except comments)
"amixer -q set Master toggle"
XF86AudioMute
"amixer -q set Master 7%-"
XF86AudioLowerVolume
"amixer -q set Master 7%+"
XF86AudioRaiseVolume
"mpc prev"
XF86AudioPrev
"mpc toggle"
XF86AudioPlay
"mpc next"
XF86AudioNext
"mpc stop"
XF86AudioStop
Any ideas of the origin of this effect? Or ideaes where to start to dig?
P.S. by the way, just curious why showkey -s and xev can show different codes for the multimedia keys?
Last edited by ogronom (2009-04-25 01:37:40)

Recently disappeared all keybindings for
mpc ...
commands
Last edited by ogronom (2009-04-25 01:47:34)

Similar Messages

Error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working'

error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working' My broadband is BT Infinity with a very strong signal throughout the house and my operating system is Windows XP. My printer will not connect wirelessly to my network, what can I do with respect to the error message 'Wireless Radio not Working'

Hello @GeoffH777 ,
Perfect! You are very welcome, I am very happy to hear the reset helped!
If you have a quick moment, please scroll back to my last message here and click the "Accepted Solution" button, so others can find our thread if they happen to run into the same issue.
Greatly appreciated, have a wonderful day!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Auto To working for one material and not working for other material

Hi,
Hope everybody is doing fine.
I have configured the auto TO. Its working fine for one material and not working for the other material. I checked the material master and wm 1,2 views have the same fileds / values. What could be wrong?
I didn't setup the back ground processing job. Is that is affecting it?
thanks for any help.
regrads,
KHAN

Thnaks,
You are right but then what could be wrong? Its working for one material and not working for otehr material? Any clue?
Appreciate your time charlie

One headphone does not work or works 50% of the time. What is best way to resolve?

one headphone does not work or works 50% of the time. What is best way to resolve?

First of all, I'd recomend resetting the iPod. Do this by pressing the 'Menu' and 'Center" buttons for 10 seconds or until the Apple logo appears.
If this doesn't work, then it sounds like a hardware fault.
To identify the issue, if you have one, try plugging the iPod into a speaker through the dock. If this works, then the issue is with the headphone jack. If not then the logic board is dead. If the iPod is less than a year old, then it can be repaired by Apple for free. Just book an appointment for the Genius bar.
If not then, you could see about sending it to an iPod Repair Company, such as my own. A replacement headphone jack would cost £30.00 in the UK, including next day delivery. Other companies you could try would beUKiPodRepairs, but we guarantee to beat any quote that you get.
Hope that this helps,
Mark Sweeney
Dr Pod Founder

HT204065 Group text with one non iPhone not working on iPhone 6 in the group.

Group text with one non iPhone not working on one iPhone 6 in group. SMS, MMS and iMessage as well as group messaging are all turned on. Has worked intermittently but now cannot see or respond in that particular chain. Can send independently to the non iPhone (Samsung) but not in group. Other iPhone 6 and 5 in group work fine.

The reason why you have to turn off 3Gs is because T-Mobile does not support iPhones 1700 something or other. You have to turn off the 3Gs on the iPhone to make it work.
As already provided, it shouldn't matter since the iPhone is designed to automatically connect to the fastest internet connection available. If wi-fi access and 3G network access is on, when in range of an available wi-fi network you have access to and have connected your iPhone with previously, the iPhone will connect to the wi-fi network automatically. When leaving the range of the wi-fi network, the iPhone will connect to the 3G network if 3G network access is available. If 3G network access is not available, the iPhone will connect to EDGE or GPRS - whichever is available at the time.
If this is unique to T-Mobile's network with the iPhone for some reason since T-Mobile is not an official carrier for the iPhone in the U.S. and you were instructed by T-Mobile to do so, then you need to do so.
If this is not working now, the problem lies with T-Mobile and I have no idea what to tell them for them to recognize where the problem lies on their end.

One speaker is not working since long time

one speaker is not working since long time bought in last december

I have iphone 4Gs and I can see at bottom there are 2 nets for speakers and I saw with my college has same iphone and sound is coming from both but mine is coming from only from right side.

[S210 Touch] One key recovery not working

I have a 1.25 year old S210 Ideapad Touch. I made a 100GB partition with EaseUS and had no problem with onekey recovery. I tried to merge that empty partition with my C drive using EaseUS software but it did not work saying there were errors. After that attempt One Key did not work. Tried to open One Key with compter turned off, error message said damaged partition. Next I used Control panel Administrative Tools: Disk Management to return C drive to almost its original size less 350 mb. one key still did not work. I reinstalled one key from Lenovo website and still did not work. Still indicated damage partition. What can I do now?
Jim
Moderator comment: New thread created. Subject edited for clarity. Was: Re: One key recovery not working!

I found the following on a recovery disk which I made early last year for the same computer but I cant get it to boot.
How do I boot this usb flash drive without losing this material and is it used to recreate the correct partitions?
convert gpt
create partition primary size=1000
format quick fs=ntfs label="WINRE_DRV"
assign letter="W"
gpt attributes=0x8000000000000001
set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
create partition efi size=260
format quick fs=fat32 label="SYSTEM_DRV"
assign letter="S"
create partition efi size=1000
format quick fs=fat32 label="LRS_ESP"
assign letter="I"
gpt attributes=0x8000000000000001
set id="bfbfafe7-a34f-448a-9a5b-6213eb736c22"
create partition msr size=128
create partition primary size=436224
format quick fs=ntfs label="Windows8_OS"
assign letter="T"
create partition primary
format quick fs=ntfs label="LENOVO"
assign letter="O"
shrink minimum=12288
create partition primary
format quick fs=ntfs label="PBR_DRV"
assign letter="Q"
gpt attributes=0x8000000000000001
set id="de94bba4-06d1-4d40-a16a-bfd50179d6ac"
exit
Thanks for any help,
Jim

Go back one page does not work

Since I had to reinstall Firefox 3.6.15, the "go back one Page" does not work in many cases. Sometimes by clicking on history and manually returning, it works. Id there a fix for this problem, because it is new.

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]

One headphone does not work

My left head phone made by apple does not work very well.
The sound quality on the left one is very poor and it's volume is very quiet compared to my right headphone.
I have tried other headphones to work with my iPod but the left one still does not work.
This has happened to other people I know, they sent it in to Apple, and Apple did nothing to the iPod. IT IS NOT THE HEADPHONES.
The iPod is the part that has the problem.

If you have tried different headphones with your iPod
and only one channel is working then probably a
connection between the jack and the logic board has
broken. This has been happending with headphone jacks
since they have had headphone jacks.
All too often it is caused by jerking the headphone
plug out of the jack, and it ends up coming out
slightly at an angle. This can cause pressure on the
jack and break a solder. Other times it is just a
factory defect. If you are sending yours in they will
fix it either way, but in the future I'd be very
careful when plugging in or removing the headphone
plug.
I'd went through a series of Sony high-end cassette players that had this exact problem...luckily my credit card's insurance covered their replacement given that they all failed after the Sony 90 day warrant expired. As a matter of act it was that experience that brought me to Apple iPods.

LaserJet Pro MFP M125nw - Scan to app All-in-One Remote does not work

Hi gurus,
Basically I have pruchased that super-printer and I am now trying to achieve scan to my mobile devices.
I have one iPad 2 on iOS 7, on 2 Android devices (smaller tablet and phone) both running Kitkat 4.4.2
I am trying to submit a scan from all these devices and retrieve the output within my mobile devices, actually this is fairly described here and concerns accurately my printer model : http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02486319&tmp_task=useCategory&cc=us&destPage=pr...
Unfortunately, What happens :
- From my iPad, the AiO app states that my printer is not compatible with the application !!
- From my 2 Android devices, the All-in-One Remote app will work fine, except the scan feature as nothing happens (well, when tapping either 'Preview' or 'Scan' button in the Scan section, I see a 'Cancel' button during 0,1 second and I am back to that scan section)
Any one could help please ???
This question was solved.
View Solution.

Hello,
Can no one help ?
Is the product description misleading ? Is the AiO app not really reasy to support this printer ?

HP Photosmart C3180 All-in-One printer -- SCANNER not working.

I have had this HP Photosmart C3180 All-in-One printer for a couple years and all is well. HOWEVER, the one function not working properly is SCANNING. I can print fine and copy fine. But when I go to scan something my power button flashes for about 10 seconds and then stops. Nothing happens, and nothing scans. HP said it was not the printer itself, but something to do with my operating system through Apple. I have the current 10.5.6 version of Leopard.
If I can get any help from others I'd appreciate it!

HP provided this link to software which resolved my scanning issue.
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=mp-55009-3 &lc=en&dlc=en&cc=us&lang=en&os=219&product=1146331

Help...Brightness control button in Lenovo All In One C360-4061 not working

Hi,
I just bought All in one C360-4061, and the monitor very birght,it hurts my eyes...i tried to push the birghtness control button but not working.i tried the keyboard shortcut (fn+home and fn+end) but not working either.
anyone can help how to solve it ???
thanx
best regards
Solved!
Go to Solution.

hi esurjopurwanto,
Welcome to Lenovo Community Forums!
Open device Manager and look under Display adapters.
Uninstall the Intel HD graphics place a check under delete driver software for this device.
Then Download and install this driver for your Windows 8.1
Intel VGA Driver
Please let me know your findings
Cheers!
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

7520 All in one web services not working

I got notified of a new update for the 7520. When I tried to install it, the screen said it was successful but then said "updating....do not turn power off" and it freezes and the update never gets successfully installed and I have no web services. I tried reiinstalling the whole software package, restarted the printer multiple times and the router too and can't seem to find an answer. Anyone know what to do next?

bjg1,
Welcome to the HP Forum.
Assuming you can get to the point where you can get the software installed, you might be able to get Web Services back using the following workaround.
Suggested Workaround:
On the printer, Disable the web services -- that is, remove web services from the printer.
This may then allow you to then "Enable Web Services".
There is a consequence to this action: Your previously selected ePrint custom address will no longer be valid and cannot be reused. When you go back and log into your HP Connected account you may need to not only "add device" to re-add the printer to the device list of ePrint printers, you will have to select a new custom email address for that printer.
Where / how is this done?
Side Bar: The Disable Web services is usually done on the printer, although if the service is actually working, one can switch off EWS from EWS.
Disable EWS on the printer, wait a few seconds, and then Enable the service again.
Switching off EWS does not "break" your HP Connected account, although it does put a crimp in your printer's ePrint setup. You can still log into the HP Connected account where the printer and the ePrint account is managed. After EWS is disabled / enabled, you must log into your HP Connected account.
If you do not find your printer listed under the Devices tab, you can usually "add device" and add your printer right back into the list at this point.
If you do find your printer, but it won't cooperate, it won't update, you cannot "do" anything with it, go ahead and remove it.
If you have to "remove the printer", then Log out of HP Connected.
If you have to "remove the printer", then Walk around your house / office / back yard -- come back.
Log into HP Connected and use "Add device" to add your printer.
Update the ePrint email address to something new - add a number, think of something new and clever; it does not matter as long as the name is different.
Click the Kudos Thumbs-Up!
It is a nice way to say “Thank You" for the help.
Although I strive to reflect HP's best practices, I do not work for HP.
Kind Regards,
Dragon-Fur

8500 All in One - touch screen not working

One minute the touch screen with all it's functions was working fine and then, bam (!), the touch screen stopped working and I can't even use the one/off switch to power the unit off - it does not respond. Funny thing is that the printer is still working from my computer so I can still send a print job via the wireless. With the touch screen not working I can't use any function from the unit itself (copy a hard copy, fax a hard copy) and if the unit runs out of paper I have to unplug it to reboot since I can't hit the 'enter' on the touch screen once I've reloaded.
Bottom line --- nothing from the unit itself works. Has a printer fairy locked me out or does this sound like a hardware error? Thanks for any help ...
Linda T

Excellent. Let me know how round 2 treats you. The sad demise could have been due to a couple of things...as a side question, is the climate where you live especially dry right now? I may request that our testers recheck how well we handle a static shock on the product if it is dry where you live.
Regards, CF
I work for HP and hope to make your day Sproutastic!

C7250 All in one Wireless radio not working

I have a C7250 All in one printer that suddenly the wireless stopped working. I ran the wireless test and it says the radio is on but the radio fails. The wireless LED is on, any suggestion on what could be the problem?

Shut off the printer. Hold the # and 6 keys while and a for a few seconds after turning it back on.
If that does not work, it is toast. You could plug it into your router with an Ethernet cable and it would have the same functionality and still work with wirelessly connected computers.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Xbindkeys -- one combination is not working

Similar Messages

Maybe you are looking for