Xbox one upnp port forwarding

Latency pretty hight never had issue like this b4 so need some help
would it be best to turn upnp on or leave it off if i need to turn it on how do you do that?
also any link to port forwarding the xbox one?
home hub 5 type b

this is another https://community.bt.com/t5/Other-Broadband-Discussions/Xbox-one-moderate-NAT-on-Homehub-5/m-p/11091...
try using the search at the top of the forum and see how others have solved the problem maybe save you some effort
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Similar Messages

Wrt160nv2 xbox strict NAT port forwarding/port triggering

I am having trouble stabalizing my NAT on 2 Xboxes. They are both connected to the wrt160nv2 with ethernet cables and I don't know whether I need to do port forwarding or port triggering. Right now, I am using port range triggering, triggered range 53 to 3074 and forwarded range 53 to 3074, and under Setup, MTU size is 1452. I got that off of another post on here but I think they were trying to set it up for an ethernet cable and wireless. I just need to know what to do since both Xboxes are using ethernet cables so both Xboxes can have open NATs.

No need to forward/trigger any ports on the router . Sometimes 2 gaming consoles do not work on a router.
You can try to upgrade the firmware on the router , reset it and reconfigure .

Port Forwarding PAP2T-NA

How does one configure port forwarding in the PAP2T-NA? I have checked the configuration pages and don't see anything labeled as such.

The PAP2-NA is a VOIP adapter and not a router . You cannot forward ports on a VOIP adapter. IF you are looking to forward ports, you will have to do so on the router itself.

Xbox 360/one problem and port forwarding

For a couple months now (since I got my AirPort Extreme) I have not been able to connect to a certain friend on xbox. I can connect to anybody else however. The only way we can (kind of) connect is if somebody else is host and we both connect to him.
My NAT type is Moderate. When I try to test my connection on my xbox it says that I can connect but I am limited in matchmaking (this is joining games and using voice chat, which is the problem named above for my particular friend). The xbox shows the error and suggests that I enable UPnP or open the port 3074.
The problem is that I have already have! I gave my xbox a static IP and forwarded the port 3074 to that IP.
(I have also tried forwarding all the ports that xbox live uses to the xbox. These being:
Port 88 (UDP)
Port 3074 (UDP and TCP)
Port 53 (UDP and TCP)
Port 80 (TCP)
as found on the xbox website... https://support.xbox.com/en-US/xbox-360/networking/network-ports-used-xbox-live
I made sure to put them in the right text boxes for UDP and TCP so that is not the problem either.)
I know that the AirPort Extreme does not support UPnP but does have a similar thing called NAT Port Mapping Protocol which was already enabled. (I tried all possibilities of enabling/disabling NAT...Protocol and port forwarding/not port forwarding.) --- This is not the solution as I see it
In short: My xbox tells me to open port 3074. I already have. It still tells me to open it and still won't work.
I posted this on the apple discussion page (instead of the xbox discussion page) because I know that it's not an xbox problem. When I had my old linksys router it worked perfectly.

I have this exact same question and problem. I know this doesn't help, but would appreciate any updated information if you find an answer. I'll keep working on this also and let you know if I find an anwer.

Port forwarding for XBOX One on Airport 6.3.1

Hi there, firstly i'm going to have to say i'm not particularly technical whatsoever when it comes to computers but i'll try and be as precise as possible.
I purchased an XBOX One console last week along with several games. They all work fine both offline and online for multiplayer gaming.......all that is except for Call of Duty Ghosts. When I load this game up with the disc in the drive the multiplayer option only allows me to select 'Local Play' (offline with bots essentially). I've tried erasing profiles, deleting and re-installing the game but the same issue happens. As I say, every other game works fine when it comes to playing online.
I spoke to Microsoft who informed me that my ISP (Suddenlink) will open up the following ports: Port 88 (UDP), 374 (UDP and TCP), 53 (UDP and TCP) and 80 (TCP) and that they will also do 'double NAt-ting'. I contacted my ISP and they informed me that they can't do that due to all sorts of security risks - trojan virus etc - and that if I want those ports to be open I will have to do it myself or "get somebody else to do it who is tech savvy".
If it helps I have an Arris modem (TM602G/115) and the router being used is the Airport Utility. According to my registered Apple product purchases it looks like I have an Airport Extreme 802.11n (4th Gen). Today I updated it to get the latest firmware/update so I think it's as up to date as it can be.
So essentially i'm wondering what screens to go into and what to type into the boxes to get this game to work so that I can play it online with friends because neither Microsoft or my ISP are willing/able to do this.
Thanks in advance,
Alex

For the record I did read the following post - I followed the instructions and changed the settings but i'm still presented with the 'Local Play' only options in the multiplayer section for Call of Duty Ghosts. Again, every other game works, it's just this one which is causing issues.
https://discussions.apple.com/message/20779016#20779016

Question about port forwarding 2 xbox 360s to get rid of NAT on one of them

I have a xbox 360 with the official xbox 360 wireless antenna that is already set up for port forwarding and my NAT is fine. My brother has a xbox 360 and he has a NAT problem but he doesn't have a official xbox 360 wireless antenna, he hooked up his laptop to his xbox 360 via ethernet cable and is using his laptops wireless card for the connection and he gets a NAT error when he tests his connection to xbox live. Is it possible to port forward 2 xbox's? I'm sure I have to set up some type of static IP for him but the thing is that I'm not sure what IP address to assign to him. If it is possible, would he have to use a static IP address on his laptop since he's using that for a wireless connection? If this is at all possible could someone post some step-by-step instructions on how I should set this up? Below I will give you what I have set up for my xbox 360 to open up my NAT I just want to know what static IP I can use for him. Can I use just any numbers?
In my port forwarding tab in my wireless modem I have the following:
and in my xbox i have the following settings:
IP address: 192.168.1.20
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
Primary DNS: 4.2.2.2
Secondary DNS: 192.168.1.1
I have all that entered for myself and my xbox NAT is open. I just need to set up his xbox if it is at all possible. Please help!!!
P.S. My router is a WRT54GS v2.0 with updated firmware, just incase you need that info.
Message Edited by nourotherleft on 01-08-2009 03:20 PM

ok that still didn't help me.... he still has a NAT problem.... I don't....I went to port triggering and added the ports that you described but it didn't open his NAT... If the connection is going through his laptop(acting like the xbox 360's wireless antenna) wouldn't either his laptop or his xbox need a static ip? because I had to set up my xbox manually with the following addresses:
ip: 192.168.1.20
subnet mask: 255.255.255.0
default gateway: 192.168.1.1
primary dns: 4.2.2.2
secondary dns: 192.168.1.1
so in essence wouldn't his laptop need to be configured with some kind of static ip or something? because if he puts in what I just stated into his xbox it wont connect at all because I guess the ip's are conflicting....so what do I do now?

Can anyone tell me how to port forward and setup an XBOX 360 using my Time Capsule??

Xbox 360
When playing the game online, the minimum speed of your network should be 128kbps. The ideal network speed for playing the game online is 768kbps. If you are having a problems with lag check the following:
Network Troubleshooting:
Disable any firewall or security features on your router.
Set port forwarding on your router to the IP address of your Xbox 360. This game uses port 3074 (UDP/TCP). Additionally Xbox LIVE requires ports 80, 53 TCP and 88, 53 UDP.
Place your Xbox 360 into the DMZ of your router.
Disconnect your router and try the game. If it works regularly at this point something about your router may not be completely compatible with the specific needs of this game. Check with your router manufacturer and Microsoft's Xbox Live Connection Issues page for additional steps that may need to be done to resolve the issue you are having. You can also verify that you have an Xbox Live compatible router.
If you are having issues connecting while multiple Xbox 360 consoles are connected on the same network, try forwarding port 3074 (UDP/TCP) for one Xbox 360 and setting the other as DMZ. There is a chance that this may not resolve you issue, if it doesn’t then you may want to consider getting an additional public IP address by contacting your Internet Service Provider and assigning it to one of these two consoles.
NOTE: If setting port forwarding or DMZ helps your connection issue, you may want to assign your Xbox 360 a static IP address within your home network. This can help to ensure that the configurations you made do not need to be done again. You can visit PortForward's Static IP Guide for a detailed guide on how to do this.
NOTE: Many broadband internet modems are coming with routing capabilities built in. Please contact your internet service provider to determine if your internet modem has an integrated router. If it does, they should be able to assist you with the steps above for setting up your router.
Once you have verified that your network setup is not the cause of the issue, try the following:
Try connecting to a different server. Some servers may have other players connected to them that you do not have an optimal connection with. In most games this is accomplished by backing out to the main menu and then selecting multiplayer again. From there you can try connecting to another online game.
Run the Xbox Network Self Test to see how strong your NAT is currently set to. Once the test is completed you will be notified if there is an issue with your connection. If you select "More Info" you will be given information about your NAT type and some steps to resolve any issues with your connection.
Moderate and Strict NAT types may have issues connecting to online matches. You may get the error "Notice - The game session is no longer available." If you do then enabling UPnP, forwarding port 3074, or placing your Xbox in your router's DMZ may resolve this issue. Please consult your router documentation for instructions on how to do this.

ouman88 wrote:
Whoa....this just went way over my head.... I already have 6.1 installed for my Airport Utility.
Read again what I wrote.. 6.1 is the problem.. or part of it.
You need to install the earlier 5.6 version which I have given you explicit instructions to do.
I have done something now and can not connect the XBOX at all now....unless you can provide me step by step directions I may have to call Apple Support.
This will happen over and over.. just press reset and start again.. you need to learn how to do the setup and using 5.6 utility will help you.. as will using ethernet from the computer to the TC.. trying to fix things over wireless is like sitting on a tree branch you are sawing off. As soon as you update you will fall to the ground.
I am not that sure that Apple Support will have any idea.
Do a google search .. you will find most people struggle with this.. Microsoft made the xbox to use upnp with vista specs.. if you use a router without upnp, ie any apple router.. you will have issues.
Have a go at bypassing the problem.. I have no idea if this will work.. I do not use a TC as the main router because much of my network including xbox and ps3 is just a pain.. I use a modem router with upnp. And bridge the TC.. that is the setup I would recommend.
Try this.. once you have installed 5.6 utility.
Get the IP of the XBox and click enable default host.. and put the IP address in there.. this is called DMZ.. all unassigned packets are forwarded to this ip address.. it is like a port forwarding for all ports.
See if it helps.. If it does you will need to lock the xbox address so it doesn't change.. we can get to that.
Tell me what kind of broadband you have and what modem router first.. none of this will work if you have double NAT.

WRT320N. Port forwarding help. Xbox and ps3 playing at same time. NAT issues

Hi
I'm trying to have both my xbox and ps3 play with open NAT's for online gaming. I have had success utilizing info from 'portforward.com'. But the solutions will unlock OPEN NAT for either the ps3 or the xbox .. one at a time. Is there a way to get both to be open?
It seems like one main conflict is the success depends on both utilizing port 3074. But I can't have both use it? ( obviously).
I tried port forwarding the xbox per specs off of this forum and that works great.. And DMZ ing the PS3. But like i said before. Most solutions
leave one console with OPEN and one with Moderate.
Is there a solution that allows both NAT OPEN's on both consoles?

First of all XBOX works on a different port number and PS3 works on a different port numbers. Follow the steps below to open the ports on your router for XBOX and PS3.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
This settings are for your XBOX.
On the set-up tab change the MTU Size to 1365 and click Save Settings...
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
For PS3 Follow the steps below
Click on "Administration" tab and disable the option UPnP and click Save Settings...
Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the fourth line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the fifth line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the sixth line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...

Port Forwarding for Xbox Live

My eyes are burning from trolling the boards all day. Just picked up an AEBS (12:33 PM CST, 4/20/08), firmware's at 7.3.1, connected the ol' xbox and got a "moderate" on my NAT test. Thats fine, totally expected, no big deal, right? So here's what I do:
1. Assign static ip ads to all machines on the network (xbox is 10.0.1.3)
2. Check to see if NAT is enabled in airport utility: Yep.
3. Enter in the ports as usual:
Public UDP Port(s): 88,3074
Public TCP Port(s): 3074
Private IP Address: 10.0.1.3
Private UDP Port(s): 88,3074
Private TCP Port(s): 3074
The above, BTW, is exact as far as commas and spaces go.
4. Update!
Then, NAT test= Moderate.
OK, it'd be nice if there was a standardized way to forward ports on all routers, I think, no big deal, just need to do a little tinkering.
I put a space after the comma between 88 and 3074, i.e., instead of 88,3074 I did 88, 3074. Moderate. I tried putting a dash in there (88-3074) wouldn't even let me do that, but of course we all already knew that. Tried rearranging all the ports randomly (3074,88). Nope. Well, even though I just gave the machine a static ip address, might as well try a DHCP lease: enter Airport ID. Nothing. Try it again with Ethernet ID. Nothing. I've got an idea, I'll make multiple separate port mapping profiles:
xbox 1: Public UDP Port(s): 88...
xbox 2: Public UDP Port(s): 3074...etc.
NAT test= Moderate.
Hmm, Oh they make port forwarding management software? Lighthouse, eh? I'll try that...oh, it doesn't do anything: Moderate.
I tried a bunch of other things that I knew would be futile, but I've been working on this thing for a couple of hours now and I can't remember them...Oh and by the way, for those not familiar with xbox live: "Moderate"= not good.
I'll telepathically make you feel better if you can help me out.
Love ya,
Boo

Thanks for the prompt reply Duane. Just to clarify: I need another wireless router? I thought airport express was one. I was trying to configure the ports of the airport express's basestation. My connection system is:
-An ADSL 2mbps connection that comes into my home from a phone line and into a D-link GLB 802C modem
-This connects to an Airport Express
-My macbook pro uses the net through the wifi signal provided
-I connect the macbook pro to the xbox through an ethernet cable (mainly because it's far from the adsl router)
I have read that one can forward ports with airport express...

Port Forwarding - XBOX Live & PS3

Hello BT Forums!
I am having trouble with my BTHomeHub 3, XBOX 360 & PS3. In my household we have both consoles, and we play Call of Duty: Modern Warfare 3 on both.
Now, with the BTHomeHub3 on the "port forwarding" menu I am only allowed to select one either "XBOX Live" OR "PlayStation 3" not both, it just brings up an error saying I can only select one and to change I have to remove the other.
I have my PlayStation 3 set with "PlayStation 3" port forwarding on the admin settings, but this puts the NAT settings on the XBOX to "Strict". Then if I take the port forwarding off the PlayStation 3 and set port forwarding for the XBOX it puts my PlayStation 3 NAT on "Strict". There is no winning!
Is there anyway I can select both, without having to resort to DMZ (makes my connection unstable).
Thanks!

Hi dlmatthews and welcome to the forum, i've had the same issue, you can't port forward to both, I just DMZ my PS3 and port forwarded to my another PS3 in the household.
If you want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side If the the reply answers your question then please mark as ’Mark as Accepted Solution

Port-forwarding or UPnP on VERIZON FIOS modem/router

I'm trying to help someone access his home network remotely from another location. he just got the new Verizon FIOS network.
i'm new to the world of port-forwarding and UPnP forwarding, but have learned a lot in a short period of time.
I can easily setup port-forwarding and UPnP forwarding (necessary to setup the afp file sharing, screen sharing, etc) on Linksys routers that have those capabilities.
My friend just got the new Verizon FIOS network installed. It is smoking fast both up and down. We figured out that the box Verizon provided him (it's a fairly huge thing) is an internet modem, a router, and a wireless router all in one.
And once we accessed its control panel, I definitely saw places where we could configure port-forwarding........
but it's not quite as straightforward as it is on a Linksys router in that, on a Linksys, if I want to open a specific port, like 5900, for screen sharing, I can easily type in the numbers 5900 and type the IP address of the computer on my LAN that I wish to forward port 5900 traffic to.......or I can do this with UPnP forwarding....either way it is simply and fully controllable.
But on this Verizon box, it seems to have most standard ports and protocols stored in presets that you must choose from. For example, if I wanted to setup port forwarding for FTP traffic, I would choose FTP from the dropdown menu and then the router would automatically know to forward port 21 to the computer of my choice.
but we specifically want to turn on AFP for apple file sharing, which is port 548. On the Linksys, i could simply type port 548. But this Verizon router does not show a service called AFP. It has a nice LONG menu of many different pre-set options, but AFP is not one of them. Would it be called something else on a device like this that is obviously not specifically designed to know Apple's file sharing protocol?
So would anyone know what kind of service I should look for that opens port 548 for file sharing?
Anyone have experience with these new Verizon routers/modems yet? I'd really love to find a way to type everything in manually, but I dunno if that's possible on this unit.
i know there's a lot here. thank you to anyone who knows about this and can shed some light

That doesn't work because applications that initiate outbound connections are given randomly assigned 5-digit port numbers (e.g., 49144) through which the CLIENT communicates. The "well known" port numbers like 548 for afp, 22 for ssh, 80 for web servers, etc., are for the SERVER function to which the server daemon listens. Example: you don't send the request to download your email from your pop 110 (or 995 when using SSL), or from your imap 143 (or 993 when using SSL); that's the port number at the DESTINATION server to where your traffic is delivered, i.e., the port to which that SERVER is listening for incoming traffic. Same for when you send mail, you send from some randomly assigned five-digit port number TO the smtp server's port 25. You can see this by launching Terminal.app from an admin-privileged account and typing sudo tcpdump -i en1 (use en1 for airport, en0 for wired ethernet) and looking at the packet transmissions' headers.

Port forwarding versus UPNP on Linksys router

I use ichat3 to videochat with my two sons, both of whom use Trillian on their PCs. Just lately, successful connections have become a rarity - much less than 50% - either failing to start the chat entirely or without audio.
I have a Linksys WAG54G router (usually connected either wirelessly or via Ethernet to my G4 PowerBook) with UPNP enabled. Yesterday, it seemed that I could connect to the Apple test sites much more reliably if I disabled UPNP. For example, I consistently had no sound from appleu3test01 with UPNP enabled but it worked properly every time I disabled UPNP.
I am thinking of assigning a static IP address to the PB and changing my router set-up to Port Forwarding in the hope of a better success rate. I've looked at the WAG54G section of the portforward.com website and the suggested iChat settings are:
Single port page:
Application     Ext port      Int port     Protocol     IP address
ichat1     5060     5060     Both
ichat2     5190     5190     Both
ichat3     5220     5220     Both
ichat4     5222     5222     Both
ichat5     5678     5678     Both
Port range page:
Application     Start     End     TCP/UDP     IP address
ichat6     16384     16384     Both
Some questions before I proceed:
1 Shouldn't the end port for entry ichat6 be 16403?
2 Are 5220 and 5222 only for Jabber users?
3 What about other ports such as 5353 and 5297/8 - I don't use Bonjour but I do have other Macs on the same network?
4 Is there any advantage in specifying TCP or UDP for the ports that only need one?
5 Any reason to suppose that port forwarding will in fact be better than UPNP?
Any help will be much appreciated.
Dave

Hi Dave,
Well spotted.
iChat6 should be 16384 as start and 16403 as end.
In fact the others would be more secure if:
ichat1 5060 5060 UDP
ichat2 5190 5190 Both
ichat3 5220 5220 TCP
ichat4 5222 5222 TCP
ichat5 5678 5678 UDP
They were pointed at the Protocols that are actually used.
Re 2 Yes 5220 and 5222 are for Jabber (in Fact Jabber also uses port 5223 for SSL logins All of which are on TCP)
Re 3 Bonjour is a handy way to do file transfers but someone does have to be there to accept and deliver file (compared to file sharing which does not) If you are not using it you will not need 5297, 5298 or 5353 on the variuos UDP and/or TCP protocols they use
RE 4 See security above.
Re 5 If you have multiple computers UPnP is best as Port Forwadring on many domestic devices does not allow the same ports to be forwarded to different IP addresses (Computers)
For more Security some devices do allow you to set the number of devices away from the UPnP device that it can be "seen" (Descibed as Hops and usually set to a default of 4) I can not find a palce to change this on my WRK54G Wireless router)
Ralph

Can I use my late 2013 Macbook pro as a display for my xbox one. I am currently sick with the flu and I do not have a tv in my room. Is there anyway to use the hdmi port on my mac and connect it to the xbox one?

I am currently sick with the flu and in my room I dont have a tv. I tried plugging my xbox one's hdmi into the hdmi port on my macbook pro late 2013 retina display. I even tried connecting the hdmi cable to a hdmi mini display mort converter and that didnt work. How can I use my Macbook as a monitor to play game on

I would guess that the HDMI port on your mac is for output only - no input, and that's what your'e attempting to do when you attach the mac to your xbox. I looked in Mactracker and it lists the HDMI port as video output for both the 13" Retina MacBook Pro and the 15" Retina MacBook Pro (your post didn't say which one you have), so looks like that is the issue..

I have a game on my xbox one that is telling me I need to open ports in order to play it I am not all that tech savvy and have no idea how to do this

I have an airport extreme and I am trying to play a new game on my xbox one and it keeps kicking me I have comcast internet that is more than fast enough so I went to the games site and it says I need to either create a static ip or to open ports no idea how to do either of these or what that does any help would be appreciated.

There are heaps of posts here about how to open ports on apple routers specifically for xboxes.
AirPort Extreme and xbox 360

How to Port Foward Xbox One?

I don't know how to port foward the Xbox One to make the NAT type Open with my AT&T Unite Express device. I see the port fowarding option in the device's website, but don't know how to do it. Please help!

I'm having the same issue, has anybody managed to resolve this?

Xbox one upnp port forwarding

Similar Messages

Maybe you are looking for