Xboxdrv controller not detected by Escape Goat 2

I'm trying to use the xboxdrv driver (for my xbox 360 controller) instead of the xpad driver and I'm having some issues with it not being detected by Escape Goat 2. Here are my results:
Steam + Escape Goat 2 + Xpad = Controller detected and works fine
(i.e. ran escape goat 2 from steam)
Steam + Big picture mode + xboxdrv = works fine
Steam + other linux games (e.g. towerfall ascension) + xboxdrv = works fine
Steam + Escape Goat 2 + xboxdrv = controller not detected
Escape Goat 2 + xboxdrv = works fine
(i.e. ran escape goat 2 from outside of steam)
I think the last result is most interesting.
Any ideas on why it's not being detected when run via steam?

Similar Messages

Ide 2 controller not detect

hi, THIS IS NOT MSI PRODUCT,BUT I NEED YOUR HELP ,AND IDEA
my intel SE440BX ide 2 cannot detect my cd-rom,and i try to read from windows(windows 98SE)device manager the secondary ide controller not detect,but at cMOS the both of ide was enable ,the CDROM is working ,pls help me.
IF can't use ,do your know the configure the creative Sound blaster 16(CT2910)the IDE port,can your show the method

does the cd-rom detect on bootup when you set the secondary master/slave to auto-detect?
When you say that the secondary ide not detect in windows, do you mean that you only get a primary ide controller? Try going into the Main IDE controller properties (can't remember what it's called in 98), and make sure that both ide channels are enabled, this is done in device manager, it's in the same section as the primary/secondary ide controller's are.

Initio INI-9090U SCSI controller not detected

I'm having a problem with my G4 and it detecting my Initio INI-9090U controller. From what I've read so far, it doesn't look promising to get it running on OSX 10.3.9. I'm new to MAC (PC tech) but I am getting around and feel more comfortable with using it. Initio is not clear on how to update the firmware if at all possble within 10.3.9. I have tried updating the firmware witn 0S 9.1 with no luck yet.
http://www.initio.com/support/index-download.htm
On a side note, I have an Advansys ABP-915 that is MAC compatible but can't get that to run either. It looks like this one first needs a firmware update too. I ran there install app and it loaded a bunch of drivers and utilities on the root of my startup disk (chosen localtion) but none of the utilities seem to be correct for the card I have.
To explain before anyone asks, I am not really that interested in buying a new card. The G4 was given to me from work for learning opportunities in my spare time. I will admit this, its been fun so far.
Any help would be appriciated.

I don't have URLs, but a number of SCSI cards don't detect well. As an example, if I open System Profiler, it doesn't detect the card or drives attached to it. At least in the "bus" section, in the PCI card section it does see the card (Adaptec 2906)
But, the drives mount at boot and Disk Utility see's the drives and the drives mount and dismount just fine.
A lot of these cards (like mine) will NOT support booting from SCSI for that reason.
I hope this is a little help

Ricoh PCIe SDXC/MMC Host Controller does not detect SD cards

Hi,
My Lenovo Thinkpad X230 has an integrated 4-in-1 SD card reader (SD/SDHC/SDXCMMC), but it does not detect any card I insert. The two cards I have are working correctly under my sister's MacBook. My kernel version is 3.6.10. Here's the output of a few commands :
lspci -k
00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
Subsystem: Lenovo Device 21fa
00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
Subsystem: Lenovo Device 21fa
Kernel driver in use: i915
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: xhci_hcd
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: mei
00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04)
Subsystem: Lenovo Device 21f3
Kernel driver in use: e1000e
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ehci_hcd
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4)
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 3 (rev c4)
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge: Intel Corporation QM77 Express Chipset LPC Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: lpc_ich
00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
Subsystem: Lenovo Device 21fa
Kernel driver in use: i801_smbus
02:00.0 System peripheral: Ricoh Co Ltd PCIe SDXC/MMC Host Controller (rev 07)
Subsystem: Lenovo Device 21fa
Kernel driver in use: sdhci-pci
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. Device 8195
Kernel driver in use: rtl8192ce
lsmod | grep sd
sd_mod 29560 4
scsi_mod 133434 2 libata,sd_mod
sdhci_pci 10834 0
sdhci 23695 1 sdhci_pci
mmc_core 82791 2 sdhci,sdhci_pci
Nothing new happens if I type dmesg | tail after inserting a card.
I didn't find any solution after searching on Google, but it seems there are a few other people experiencing the same problem as me. I haven't actively tried anything yet.
I don't have much experience when it gets to this kind of things, so I hope there are some of you who can help me.
Thank you!
Last edited by Fayden (2012-12-22 05:13:09)

In case someone else has the same problem, there's actually a package in the AUR that fixes the problem : https://aur.archlinux.org/packages/ricoh-e823-fix/
Install it and enables it with systemd and it should work correctly!

Wism Module Controller 2 not detect IP Address

Hi, im badrul..i got one problem regarding the wism module controller. as we know in wism module have 2 controller, controller 1 and controller 2. i try to configure that wism module. but only controller 1 can used. for controller 2, it not detect the IP address that assign by DHCP. i try direct console on console port 2 on wism module, but it not detect console also. so i need help from who expert on this matter to soft my problem.

Thanks Justin on your respond
here the commands :
sh module
Mod Ports Card Type                              Model              Serial No.
1   24 CEF720 24 port 1000mb SFP              WS-X6724-SFP       SAL1329U59V
3    6 Firewall Module                        WS-SVC-FWM-1       SAD1311014S
4    8 Intrusion Detection System             WS-SVC-IDSM-2      SAD124101TB
7    2 Supervisor Engine 720 (Active)         WS-SUP720-3B       SAL1326T4VZ
9   10 WiSM WLAN Service Module               WS-SVC-WISM-1-K9   SAD132500BX
10    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL15108PHU
11    4 CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL1329U9DC
12    4 CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE      SAL1416FNEH
13    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      SAL1517CGRF
Mod MAC addresses                       Hw    Fw           Sw           Status
1 0026.0b5b.46b4 to 0026.0b5b.46cb   4.1   12.2(18r)S1 12.2(33)SXH5 Ok
3 0021.a082.b420 to 0021.a082.b427   4.5   7.2(1)       4.0(4)       Ok
4 0021.d869.d4e0 to 0021.d869.d4e7   6.4   7.2(1)       5.0(2)       Ok
7 0024.1499.51d8 to 0024.1499.51db   5.9   8.5(3)       12.2(33)SXH5 Ok
9 0024.9774.2344 to 0024.9774.2353   2.3   12.2(14r)S5 12.2(33)SXH5 Ok
10 c89c.1d2f.5a78 to c89c.1d2f.5a7f   2.3   12.2(18r)S1 12.2(33)SXH5 Ok
11 0026.0b5b.4694 to 0026.0b5b.4697   2.9   12.2(14r)S5 12.2(33)SXH5 Ok
12 8843.e11b.4eb0 to 8843.e11b.4eb3   3.1   12.2(14r)S5 12.2(33)SXH5 Ok
13 e05f.b974.e7d0 to e05f.b974.e7d7   2.3   12.2(18r)S1 12.2(33)SXH5 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Centralized Forwarding Card WS-F6700-CFC       SAL1329U27Q 4.1    Ok
4 IDS 2 accelerator board     WS-SVC-IDSUPG      CFBG8260009 2.5    Ok
7 Policy Feature Card 3       WS-F6K-PFC3B       SAL1326SS36 2.5    Ok
7 MSFC3 Daughterboard         WS-SUP720          SAL1326T1EZ 4.0    Ok
9 Centralized Forwarding Card WS-SVC-WISM-1-K9-D SAD1324048G 2.1    Ok
10 Distributed Forwarding Card WS-F6700-DFC3C     SAL1516C139 1.4    Ok
11 Centralized Forwarding Card WS-F6700-CFC       SAL1327TF1L 4.1    Ok
12 Centralized Forwarding Card WS-F6700-CFC       SAL1414EZAX 4.1    Ok
13 Distributed Forwarding Card WS-F6700-DFC3C     SAL1517CHK1 1.4    Ok
Mod Online Diag Status
1 Pass
3 Pass
4 Pass
7 Pass
9 Pass
10 Pass
11 Pass
12 Pass
13 Pass
show wism status
Service Vlan : 900, Service IP Subnet : 20.20.10.254/255.255.255.0
      WLAN
Slot Controller Service IP       Management IP    SW Version Status
----+-----------+----------------+----------------+-----------+---------------
9     1           20.20.10.1          172.28.40.11         5.2.178.0      Oper-Up
9     2           0.0.0.0                0.0.0.0                                     Service Port Up
show wism module 9 controller 1 status
WiSM Controller 1 in Slot 9 configured with auto-lag
Operational Status of the Controller : Oper-Up
Service VLAN                         : 900
Service Port                            : 9
Service Port Mac Address        : 0025.84a9.a062
Service IP Address                  : 20.20.10.1
Management IP Address          : 172.28.40.11
Software Version                      : 5.2.178.0
Port Channel Number               : 417
Allowed-vlan list                       : 8,15,19,31,40-41,44,50-51,200,208,212,800,900
Native VLAN ID                        : 900
WCP Keep Alive Missed           : 0
show wism module 9 controller 2 status
WiSM Controller 2 in Slot 9 configured with auto-lag
Operational Status of the Controller : Service Port Up
Service VLAN                          : 900
Service Port                             : 10
Service Port Mac Address         : 0025.84ba.08a2
Service IP Address                   : 0.0.0.0
Management IP Address           : 0.0.0.0
Software Version                       :
Port Channel Number                : 418
Allowed-vlan list                        : 8,15,19,31,40-41,50-51,200,208,212,800,900
Native VLAN ID                         : 900
WCP Keep Alive Missed            : 0
TQ again Justin...

Windows 8 and Server 2012. Not detecting network is a domain.

Hi Guys,
I hope I have posted this to the correct forum.
I have 2 x Windows 8 PCs that do not detect that they are connected to a domain (network location awareness not working). I can join them to the domain but they still don't recognise the network as a domain. Instead they identify it as "private".
Other PCs on the network (Win XP and Win 7) work prefectly, just the windows 8 machines don't work.
Also, when I do join them to domain I also receive this message.
"changing the Primary Domain DNS name of this computer to "" failed. The name will remain xxxx.local. The error was: the specified domain either does not exist or could not be contacted. "
I have tried the following
- DHCP and DNS has being tried both as static and dynamic (can ping DNS server which is the domain controller Windows Server 2012) .
- Updated PC NIC drivers.
- No AV is installed on either server or PC.
- Updated PC to windows 8.1.
- Disabled both server and PC firewalls.
- Check NLA service and all dependent services are running.
- Disabled all adapters on server except for one.
I am really hoping someone can help with this as I would really appreciate it.
Thanks.
Shaun

Hi Guys,
I managed to find a solution to the problem. I noticed that the DNS server zones did not look quite right. The _msdcs zone was missing the subfolders (dc, domains, gc, pdc).
To fix this issue: on the NIC adapter I had to tick the box "register this connection's addresses in DNS" (found under TCP/IP v4 > advanced > DNS tab).
I then had to remove the DNS role, reboot then re-add the role. Problem solved. Hopefully this saves someone else pulling their hair out for an entire day.

Audigy(1) Platinum PCI Not Detected By Installation CD In New Desk

Hello, I just updated to a new computer and pulled my Audigy Platinum SB0090 (with the front dri've panel) out of my old system and installed it in my new systemell E52 (AMD dual core)Windows XP SP23GB memory?) I disabled the onboard sound in the BIOS.2) Installed the Audigy Sound PCI card and dri've panel.3) Upon boot, Windows XP installs the Firewire and Gameport automatically. I tell it "no" when it prompts my to install audio device drivers.4) I try to install the current Audigy Platinum drivers from here, SBAX_WBUP2_LB_2_09_006, but it tells me no Audigy is detected and won't install.5)?I try to install the drivers from my original installation CD (PN: 220ML0003067) and am also?told that my?Audigy is not detected.6) The new PC has two PCI slots, 3 and 4. is PCIe6, 2 is PCIe. I've tried both PCI slots to no avail. The BIOS shows an audio device in whatever slot it is in. Partial Solution:7)? I went ahead a told Windows XP to search for drivers and it'sdid find?them on the original installation CD and installed them. I now have basic operations, but no dri've panel access. However, both installers above still cannot detect the Audigy. In Device Manager I now show:- Sound, video and game controllers-- Audio Codecs-- Creative Audigy Audio Processor (WDM)-- Creative Gameport-- Legacy Audio Drivers-- Legacy Video Capture Devices-- Media Control Devices-- Video Codecs?All of the above devices are working properly. Apparently I will not be able to easily get these installers to work. Is there a way I can manually?install the drivers neccessary to get current and full functionality of my Audigy and front dri've panel?Thanks

This is my view. It's all OK. It looks?if the Plug And Play function doesn't work. IRQ 0?Timer di sistema?OK
IRQ ?PS/2 Keyboard?OK
IRQ 4?Porta di comunicazione (COM)?OK
IRQ 6?Controller disco floppy standard?OK
IRQ 8?Orologio di sistema CMOS a tempo reale?OK
IRQ 9?Sistema compatibile ACPI Microsoft?OK
IRQ 9?SCSI/RAID Host Controller?OK
IRQ 3?Coprocessore matematico?OK
IRQ 5?Intel(R) ICH8 Family SMBus Controller - 283E?OK
IRQ 6?Intel(R) P965/G965 PCI Express Root Port - 29A?OK
IRQ 6?ASUS X950 SeriesOK
IRQ 6?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2834?OK
IRQ 6?Intel(R) ICH8 Family PCI Express Root Port - 283F?OK
IRQ 7?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2835?OK
IRQ 7?Intel(R) ICH8 Family PCI Express Root Port 6 - 2849?OK
IRQ 7?Generic Marvell Yukon Chipset based Ethernet Controller?OK
IRQ 8?Intel(R) ICH8 Family USB2 Enhanced Host Controller - 283A?OK
IRQ 8?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2832?OK
IRQ 9?Intel(R) ICH8 Family USB Uni'versal Host Controller - 283?OK
IRQ 9?Intel(R) 8280HR/HH/HO SATA RAID Controller?OK
IRQ 2?Controller host Texas Instruments IEEE 394 compatibile OHCI?OK
IRQ 22?Creative Audigy Audio Processor (WDM)?OK
IRQ 23?Intel(R) ICH8 Family USB Uni'versal Host Controller - 2830?OK
IRQ 23?Intel(R) ICH8 Family USB2 Enhanced Host Controller - 2836?OK
IRQ 23?Controller host OHCI compatibile IEEE 394?OK
IRQ 23?Hauppauge WinTV-HVR 67xxx Capture Device?OK

DVD drive not detected (K9N2GM-FD)

For some reason my motherboard( K9N2GM-FD) is not detecting my DVD drive.
Here is the setup I'm using:
AMD Athlon 64 X2 5200 Brisbane 2.7GHz
Kingston 2GB (2 x 1GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory
MSI K9N2GM-FD AM2+/AM2 NVIDIA GeForce 8200 Micro ATX AMD Motherboard
Seagate Barracuda 7200.10 ST3250410AS 250GB 7200 RPM 16MB Cache SATA 3.0Gb/s Hard Drive
a lite on DVD drive(model DH-20A4P33C) I bought at walmart
Antec NeoPower 550 550W ATX12V SLI Certified CrossFire Ready Active PFC Power Supply
The DVD drive is an IDE drive and it's getting power(I can open and close it).
I tried changing some things in the bios, trying a different drive, and trying a different IDE cable still can't get it to work.
every thing passes post test.
And the bios is version 1.2.
Any help would be greatly appreciated.

You did use proper standoff's to mount the board in the case?
yes
BTW, the controller is turned on I presume.
yes
If all is mounted correctly and there isn't any short, then I would RMA the board.
Ok I'll RMA it
Thanks for the help

PXI-8532 DNET card is not detected in MAX

Hi all,
I'm using NI PXI-1031(4 slot PXI chassis). I have the following cards in the respective slots
Slot 1= PXI-8106 Controller
Slot 2= PXI-6259 card(AI)
Slot 3= PXI-6509 card(DI,DO)
Slot 4= PXI-8532 Card(DNET)
In MAX(Measurement & Automation Explorer), I was expecting all the above cards(PXI 6259, 6509 & 8532) to be detected under Devices and Interfaces. But only the AI and DIO cards are detected in MAX under Remote Systems>>PXI>>Devices and Interfaces.
PXI-6259 (PXI1 Slot2)
PXI-6509 (PXI1 Slot3)
The device net card, PXI-8532 is not detected in MAX. Does MAX shows/detects the DNET card?
In MAX, I selected Tools menu>>NI-DNET>>RT Hardware Configurations. Then a window prompts for RT IP address. After entering the IP address, I pressed OK. A message appears that no device is found.
Can any one help me how to detect the DNET card in MAX and do the DNET port configuration?
DNET driver version - 1.6.4
Thanks,
Raja
Solved!
Go to Solution.

Dirk,
Thanks for the reply. After updating the new driver, I am able to detect the DNET card PXI-8532 in MAX
New driver - NI-Industrial Communications for DeviceNet 2.1
But Im not able to configure the Device Net port. In MAX, I selected the menu option Tools>>NI-DNET>>RT Hardware Configurations. Then a window prompts for RT IP address. After entering the IP address, a message appears that no device interface is found.
By default, the DNET0 port is configured for the card in MAX. So I tried to communicate from LabVIEW using DNET0 port.
After installing Devicenet 2.1, an additional function palette has been added for DNET in LabVIEW.
Old DNET function palette - Instrument IO>>DNET
New DNET function palette - Industrial Communications
My original application was written with old function palette VIs which corresponds to DNET 1.6.4 version. In the download link that you shared has a description about the driver compatibility. The description says still the DNET card PXI-8532 is compatible with NI-DNET 1.x LabVIEW VIs.
With the old DNET VIs, I tried to establish communication with DNET interface port "DNET0". But it shows error while opening the interface.
Error Code ="-1074388957" - The Interface is invalid or unknown. Solution: Verify that the interface is assigned to a specific port within the Devices and Interfaces branch of the Measurement and Automation Explorer (MAX).
With the new DNET VIs(DNET 2.1.0), Im able to open the DNET interface successfully. But my original application was written in Old DNET VIs (DNET 1.6.4).
1. Do you know why the DNET 1.6.4 LabVIEW VIs are not working with PXI-8532 DNET card?
2. Can you help me how to configure DNET port in MAX for PXI-8532 DNET card?
Thanks,
Raja
LV 2009, Windows XP

My external hard drive is not detected through my Thunderbolt port. How can I fix this?

I just purchard a Seagate GoFlex Portable Adapter for Thunderbolt. I have an internal drive from an old computer that I wanted to access information on. My hard disk is not detected on the disk utility nor can i hear the hard drive turn on and "hum" eventhough the adapter is connected.
Thanks for any help provided.
Items:
Seagate GoFlex Mac Portable Adapter for Thunderbolt and Thunderbolt Cable
http://www.seagate.com/external-hard-drives/portable-hard-drives/performance/gof lex-for-mac-thunderbolt/
Seagate 200GB Internal Hard drive

Here you go
Intel-based Macs: Resetting the System Management Controller (SMC)

Seagate Hard Drives not detected by the Windows 7 installer

I've spent hours on this trying every conceivable reason, so I apologize in advance for the length on this post.
I connected a Seagate 320GB 7200.10 hard drive to a P35 chipset system and attempted to install Windows 7 RTM onto it. The installer got to the part of detecting hard drives, but could not detect this drive. Native SATA mode was enabled, and AHCI was enabled.
I disabled Native SATA mode, then after that failed I also tried disabling AHCI by setting the controller to IDE mode. Still, the Windows 7 installer refused to detect the drive.
I replaced both the SATA & power cables, verified the drives are detected by the AHCI firmware and the BIOS, and I even tried different motherboard SATA ports to no effect. I took a second , identical Seagate 320GB SATA hard drive, this time pre-formatted it inside Windows 7 RC using NTFS defaults, and again (with and without AHCI and Native SATA mode) Windows 7 will not see this hard drive either!
I even downloaded the AHCI preinstall drivers and loaded these using a flash drive. When I did Windows 7 would autodetect the ICH9 driver and I would click Next. Windows 7 would suddenly see the drive, but all options to format or create a partition are grayed out. Clicking the more info button gives me this error message:
"Windows cannot be installed to this disk. This computer hardware may not support booting to this disk. Ensure that the disk's controller is enabled in the computer's BIOS menu."
I used the AHCI preinstall drivers specific for the motherboard (Vista 64) and I also tried the AHCI preinstall drivers from Intel for Windows 7 RC 64. As of this writing Intel has not released official Windows 7 RTM Intel Matrix Storage Manager drivers.
In frustration I installed a SSD (with AHCI and Native SATA mode enabled) and suddenly Windows 7 detects the SSD without needing to load any driver (as would be expected, since Vista and 7 include Intel Storage Manager drivers by default already). I installed Windows 7 RTM 64bit onto the SSD without issue.
15 minutes later I was at the Windows 7 desktop, and Windows 7 was showing the Seagate 320GB hard drive under "My Computer" as normal. I could even use the Seagate hard drive as normal as if nothing was wrong. For kicks I launched the Windows 7 installer inside Windows 7, but as you can see below it still refused to see the drive, despite the drive being shown under My Computer:
(Since I can't use thumbnails, here's the direct link: http://i111.photobucket.com/albums/n129/Chanur64/Box/Howpossible.jpg )
Also I should note I previously had Windows 7 Beta installed on an IDE drive in this exact system, and had no problems with it. Windows 7 RTM would allow me to install to an IDE drive and allowed me to install to an SSD, but it cannot see and cannot install onto both Seagate 320GB hard drives. These Seagates are known good drives previously part of a RAID 5 array.
If anyone knows what is going on or has some ideas I've not tried I would love to hear from you and get this figured out. Suffice to say this is not a promising start for Windows 7.
Intel Q6600
Gigabyte GA-EP35-DS4 (ICH9R southbridge)
4GB DDR2-800
2x Seagate 320GB SATA 7200.10
Intel X25-M 80GB
8800GTS 320mb
PC Power & Cooling 750w PSU

I just had to solve the same issue with a Seagate Momentus Thin hard drive (
http://www.seagate.com/www/en-us/products/laptops/slim-laptop-hard-drives/)
Tried several BIOS configuration, AHCI drivers, etc and Windows 7 32bits couldn't detect the drive.
My solution was to boot with a USB pendrive with HirenCD tools (http://www.hiren.info/) and use a partition manager to erase disk contents, create and format a partition.
Windows 7 detected the hard drive for the first time and now is installing, so.. crossing fingers.
Thanks,
Diego
Diego,
Thanks for the information and the link to Hiren.info! I'm creating my bootable flash drive now. I'll report back if I get this to work.
I had this same issue on a Seagate Momentus 7200.2 "laptop" hard drive. I say "lap top" in quotes because it's actually in a desktop (HP Compaq Ultra-slim dc7800). I believe it was an upgrade, so it took me a while to figure out what I was dealing
with until I finally took out the harddrive and checked what company made it!
Thanks everyone!

S-video not detected on X700-M with free driver??

Hi,
I'm using last ati-radeon free drivers on a ATI X700 mobility and my S-Video output is not detected by xrandr.
flo ~ $ sudo pacman -Q | grep video-ati
xf86-video-ati 6.12.2-1
flo ~ $ sudo pacman -Q | grep xorg-server
xorg-server 1.6.0-3
xorg-server-utils 7.4-4
I only get my VGA output (see? no S-Video) :
flo ~ $ xrandr
Screen 0: minimum 320 x 200, current 1280 x 800, maximum 1280 x 1200
VGA-0 disconnected (normal left inverted right x axis y axis)
LVDS connected 1280x800+0+0 (normal left inverted right x axis y axis) 331mm x 207mm
1280x800 60.0*+
1280x720 59.9
1152x768 59.8
1024x768 59.9
800x600 59.9
640x480 59.4
flo ~ $ lspci -vvnn
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon Mobility X700 (PCIE) [1002:5653] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:11b2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at fe9c0000 [disabled] [size=128K]
Capabilities: <access denied>
Did I miss something in xorg config or in modules config or anywhat??
Thanks for help!
My xorg.conf is here.
My Xorg.0.log is here.

I'm having the same problem as you. I posted another thread before finding this one. I can't seem to get any replies either.
I don't know if we're the only ones having this issue or if no one else is trying to use S-video or what. I really wish I could get mine fixed. I tried the xf86-video-ati-git from AUR but it didn't help.
The only difference with my problem is that xrandr also shows a DVI-0 at the bottom. I don't even have a DVI-0. I have a VGA-0 like you do. I wonder if xrandr is detecting the S-video as DVI for some reason? Though I've tried setting up DVI-0 as I would S-video but that doesn't work.
Have you solved this by any chance? If so I'd be interested to know how. Thanks and good luck.
***My card is an ATI X1200 series by the way.
Last edited by The Avatar of Time (2009-06-30 05:50:53)

USB devices not detected in VMware [SOLVED; Using Virtualbox instead]

I am running Arch as a host and XP on VMWare workstation 7. My primary purpose of installing XP on VMWare was to use my edit my Line6 POD (behaves as a usb sound card) and get my USB TV Tuner box to work. The big problem that I am facing is that VMWare is not detecting any USB device (not even my USB Hard Drive).
I have the usb controller installed.
Any suggestions?
Last edited by devadittya (2009-11-24 20:04:45)

I don't know vmware but with other virtual machines there is often a configuration option whether usb drives should be automatically mounted or not. Sometimes automounting also only works if the vm has the focus, i.e. is the active window.

Docsis 2.0 and 1.1 cable modems are not detected via UBR-MC20X20V-5D line card

Hi All,
We have uBR10K series CMTS and recently installed UBR-MC20X20V-5D line card, requirement is to configure this line card to support docsis 1.1 and 2.0. Problem is after finished the configurations modems (Hitron and Motorola) are not detected by the system. means no modem mac address listing under "Show cable modem" command.
Our CMTS has the following components
ESR-PRE2: x1
ESR-PRE-MEM-FD128: x1
UBR10-DTCC: x2
UBR-MC20X20V-5D: x1
iOS version: 12.2(33)SCE3
Part of running-config as follows
cable spectrum-group 13 band 22800000 26600000
controller Integrated-Cable 8/0/0
rf-channel 0 cable downstream channel-id 145
rf-channel 0 frequency 501012500 annex B modulation 256qam interleave 32
rf-channel 0 rf-power 59.0
no rf-channel 0 rf-shutdown
interface Cable8/0/0
no cable packet-cache
cable bundle 1
cable upstream max-ports 4
cable upstream 0 connector 0
cable upstream 0 spectrum-group 13
cable upstream 0 channel-width 3200000 3200000
cable upstream 0 docsis-mode tdma
cable upstream 0 minislot-size 2
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
diag output attached herewith. Please any one advice on how to resolve this issue.
Thanks in advance.

Hi All,
We have uBR10K series CMTS and recently installed UBR-MC20X20V-5D line card, requirement is to configure this line card to support docsis 1.1 and 2.0. Problem is after finished the configurations modems (Hitron and Motorola) are not detected by the system. means no modem mac address listing under "Show cable modem" command.
Our CMTS has the following components
ESR-PRE2: x1
ESR-PRE-MEM-FD128: x1
UBR10-DTCC: x2
UBR-MC20X20V-5D: x1
iOS version: 12.2(33)SCE3
Part of running-config as follows
cable spectrum-group 13 band 22800000 26600000
controller Integrated-Cable 8/0/0
rf-channel 0 cable downstream channel-id 145
rf-channel 0 frequency 501012500 annex B modulation 256qam interleave 32
rf-channel 0 rf-power 59.0
no rf-channel 0 rf-shutdown
interface Cable8/0/0
no cable packet-cache
cable bundle 1
cable upstream max-ports 4
cable upstream 0 connector 0
cable upstream 0 spectrum-group 13
cable upstream 0 channel-width 3200000 3200000
cable upstream 0 docsis-mode tdma
cable upstream 0 minislot-size 2
cable upstream 0 range-backoff 3 6
cable upstream 0 modulation-profile 21
no cable upstream 0 shutdown
diag output attached herewith. Please any one advice on how to resolve this issue.
Thanks in advance.

ES1946 (Solo) Audio controller not recognized

Dear all,
ES1946 (Solo) Audio controller is not recognized on my box. I examined dmesg, it said:
es1938: OPL3 not detected at 0x1090
I've listed my dmesg and rc.conf below. Could anyone kindly look into it, and give me a hint to solve this problem?
Best regards,
Wen
dmesg
Linux version 2.6.26-ARCH (root@T-POWA-LX) (gcc version 4.3.2 (GCC) ) #1 SMP PREEMPT Tue Sep 9 10:15:21 UTC 2008
PAT disabled. Not yet verified on this CPU type.
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000bff0000 (usable)
BIOS-e820: 000000000bff0000 - 000000000bfffc00 (ACPI data)
BIOS-e820: 000000000bfffc00 - 000000000c000000 (ACPI NVS)
BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
191MB LOWMEM available.
Entering add_active_range(0, 0, 49136) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 49136
HighMem 49136 -> 49136
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 49136
On node 0 totalpages: 49136
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 352 pages used for memmap
Normal zone: 44688 pages, LIFO batch:7
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F6B60, 0014 (r0 PTLTD )
ACPI: RSDT 0BFFD520, 002C (r1 PTLTD RSDT 0 LTP 0)
ACPI: FACP 0BFFFB65, 0074 (r1 IBM TP240 2 PTL F4240)
ACPI: DSDT 0BFFD54C, 2619 (r1 PTL BX-TJ 0 MSFT 100000B)
ACPI: FACS 0BFFFFC0, 0040
ACPI: BOOT 0BFFFBD9, 0027 (r1 PTLTD $SBFTBL$ 0 LTP 1)
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 10000000 (gap: 0c000000:f3f80000)
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
SMP: Allowing 0 CPUs, 0 hotplug CPUs
PERCPU: Allocating 39464 bytes of per cpu data
NR_CPUS: 16, nr_cpu_ids: 1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 48752
Kernel command line: root=/dev/sda8 ro
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (0118d000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 365.025 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 189624k/196544k available (2120k kernel code, 6384k reserved, 744k data, 264k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffee4000 - 0xfffff000 (1132 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xcc800000 - 0xff7fe000 ( 815 MB)
lowmem : 0xc0000000 - 0xcbff0000 ( 191 MB)
.init : 0xc03d3000 - 0xc0415000 ( 264 kB)
.data : 0xc031225e - 0xc03cc380 ( 744 kB)
.text : 0xc0100000 - 0xc031225e (2120 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
CPA: page pool initialized 1 of 1 pages preallocated
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 731.57 BogoMIPS (lpj=1218523)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 9k freed
ACPI: Core revision 20080321
ACPI: Checking initramfs for custom DSDT
ACPI: setting ELCR to 0200 (from 0a20)
weird, boot CPU (#0) not listedby the BIOS.
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
SMP disabled
Brought up 1 CPUs
Total of 1 processors activated (731.57 BogoMIPS).
net_namespace: 652 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9e5, last bus=0
PCI: Using configuration type 1 for base access
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: EC: non-query interrupt received, switching to interrupt mode
ACPI: EC: GPE = 0x9, I/O: command/status = 0x66, data = 0x62
ACPI: EC: driver started in interrupt mode
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:07.3: quirk: region 8000-803f claimed by PIIX4 ACPI
pci 0000:00:07.3: quirk: region 2180-218f claimed by PIIX4 SMB
pci 0000:00:07.3: PIIX4 devres I PIO at 0398-0399
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 14)
ACPI: Power Resource [PFAN] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:09: can't evaluate _PRS: 12321<6>pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
system 00:05: iomem range 0xe0000-0xfffff could not be reserved
system 00:05: iomem range 0xfff80000-0xffffffff could not be reserved
system 00:06: ioport range 0x4d0-0x4d1 has been reserved
system 00:06: ioport range 0x8000-0x803f has been reserved
system 00:06: ioport range 0x2180-0x218f has been reserved
system 00:06: ioport range 0x398-0x399 has been reserved
PCI: Bus 1, cardbus bridge: 0000:00:0a.0
IO window: 0x00001800-0x000018ff
IO window: 0x00001c00-0x00001cff
PREFETCH window: 0x10000000-0x13ffffff
MEM window: 0x14000000-0x17ffffff
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs... done
Freeing initrd memory: 540k freed
Simple Boot Flag at 0x40 set to 0x1
IBM machine detected. Enabling interrupts during APM calls.
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 371
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:00.0: Limiting direct PCI/PCI transfers
pci 0000:00:09.0: Boot video device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial 00:08: activated
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
input: Macintosh mouse button emulation as /class/input/input0
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOUS] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 264k freed
No dock devices found.
input: AT Translated Set 2 keyboard as /class/input/input1
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:07.1: version 2.12
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1040 irq 14
ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1048 irq 15
ata1.00: ATA-5: HITACHI_DK23CA-10, 00H5A0G1, max UDMA/100
ata1.00: 19640880 sectors, multi 16: LBA
ata1.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA HITACHI_DK23CA-1 00H5 PQ: 0 ANSI: 5
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 19640880 512-byte hardware sectors (10056 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: [sda] Attached SCSI disk
ReiserFS: sda8: found reiserfs format "3.6" with standard journal
ReiserFS: sda8: using ordered data mode
ReiserFS: sda8: journal params: device sda8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda8: checking transaction log (sda8)
ReiserFS: sda8: Using r5 hash to sort names
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
es1938: OPL3 not detected at 0x1090
gameport: ES1938 is pci0000:00:0b.0/gameport0, io 0x10a0, speed 1084kHz
ACPI: EC: GPE storm detected, disabling EC GPE
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery absent)
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Sleep Button (CM) as /class/input/input3
ACPI: Sleep Button (CM) [SBTN]
input: Lid Switch as /class/input/input4
ACPI: Lid Switch [LID]
ACPI: Transitioning device [FAN] to D3
ACPI: PNP0C0B:00 is registered as cooling_device0
ACPI: Fan [FAN] (off)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: ACPI0007:00 is registered as cooling_device1
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: LNXTHERM:01 is registered as thermal_zone0
ACPI: Thermal Zone [THRM] (64 C)
Marking TSC unstable due to: TSC halts in idle.
sd 0:0:0:0: Attached scsi generic sg0 type 0
input: PC Speaker as /class/input/input5
Yenta: CardBus bridge found at 0000:00:0a.0 [1014:019a]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x012c1272, devctl 0x64
Yenta: ISA IRQ mask 0x0498, PCI irq 11
Socket status: 30000010
pccard: PCMCIA card inserted into slot 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PPP generic driver version 2.4.2
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
piix4_smbus 0000:00:07.3: IBM system detected; this module may corrupt your serial eeprom! Refusing to load module!
piix4_smbus: probe of 0000:00:07.3 failed with error -1
input: ImPS/2 Generic Wheel Mouse as /class/input/input6
NET: Registered protocol family 23
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x00001060
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia0.0
lp: driver loaded but no devices found
eth0: NE2000 Compatible: io 0x300, irq 3, hw_addr 00:40:26:5c:d8:21
nsc-ircc 00:09: can't evaluate _CRS: 12321
nsc-ircc 00:09: activation failed
nsc-ircc: probe of 00:09 failed with error -5
nsc-ircc, Found chip at base=0x398
nsc-ircc, Wrong chip version ff
ppdev: user-space parallel port driver
parport_pc 00:07: reported by Plug and Play ACPI
parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
Clocksource tsc unstable (delta = -77266143 ns)
Adding 200772k swap on /dev/sda7. Priority:-1 extents:1 across:200772k
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
tun0: Disabled Privacy Extensions
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi 2:0:0:0: Direct-Access USB DISK 28X PMAP PQ: 0 ANSI: 0 CCS
sd 2:0:0:0: [sdb] 4030464 512-byte hardware sectors (2064 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 4030464 512-byte hardware sectors (2064 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg1 type 0
usb-storage: device scan complete
/etc/rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="localtime"
USEDIRECTISA="yes"
TIMEZONE="Asia/Saigon"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(8390 pcnet_cs slhc pcnet_cs snd-mixer-oss snd-pcm-oss snd-seq-oss snd-seq-device snd-seq-midi-event snd-seq snd-hwdep snd-page-alloc snd-pcm snd-rawmidi snd-timer snd snd-mpu401-uart snd-opl3-lib snd-es1938 soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="fang.ntu.edu.vn"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network netfs crond)

hi!
did you read this?
http://tascam.com/i-414-232-128-0-4A15AD91.pdf
can be found here: http://tascam.com/products/fireone;9,14,104,19.html
regards,
m.

Xboxdrv controller not detected by Escape Goat 2

Similar Messages

Maybe you are looking for