Xircom pcmcia ethernet card problem.

Hi.
I have recently received an old Dell Latitude CPx laptop. i have added to it an old Xircom RealPort CardBus Ethernet 10/100+ Modem 56 card.
after the installation,when booting, during the start-up of networking, i get the following message:
SIOCSIFFLAGS: Cannot assign requested address
are there any known solutions to this problem?
or will i have to swap Ethernet cards?
thank you in advance
sha1

Hi,
A quick Google search indicates that 3Com XJAEM3336 Mac drivers were available for at least some PowerBook computers. However, it is unclear to me whether the files here are needed, appropriate or sufficient in your case. Perhaps you could look further into this.
If you cannot locate a suitable Ethernet PC Card with Mac drivers, another solution could possibly be to use a 16-bit wireless card (typically, 802.11b speed and WEP security). See, for example, this web page.
Jan

Similar Messages

PowerBook 1400 and PCMCIA Ethernet card

I have some problems to find out list of supported PCMCIA Ethernet cards by MacOS 7 (B1-7.5.3) on PowerBook 1400. I would be very please to receive driver for 3Com OfficeConnect 572B what I own. Is it available?
regards,

Hi,
A quick Google search indicates that 3Com XJAEM3336 Mac drivers were available for at least some PowerBook computers. However, it is unclear to me whether the files here are needed, appropriate or sufficient in your case. Perhaps you could look further into this.
If you cannot locate a suitable Ethernet PC Card with Mac drivers, another solution could possibly be to use a 16-bit wireless card (typically, 802.11b speed and WEP security). See, for example, this web page.
Jan

Is there a PCMCIA Ethernet card for Powerbook G4 OS X 10.4.8 ?

My ethernet port on my Powerbook G4 is damaged and can no longer be used. I looked into getting it repaired but that apparently requires replacing the entire system board at considerable cost. Rather than take that route, I was hoping to find a PCMCIA card with an Ethernet port but I cannot seem to find any that will work with OS X 10.4.x.
Does anyone know of such a card ?
Thanks for your help !

How old is your Powerbook?
A Mac older than 4 years old may need its clock battery replaced by an authorized service center. The clock battery dying can cause certain ports to malfunction as well. If it is under 4 years old and no surges broke the port, try zapping your PRAM, it may solve the problem once and for all:
http://www.info.apple.com/kbnum/n2238
If it is under AppleCare, there may be no cost at all. Any Mac under a year old is under AppleCare.
Also replacing the system board can be cheaper than from Apple directly if you take it to one of these places:
http://www.dttservice.com/
http://www.powerbookresq.com/
http://www.microdocusa.com/
http://www.macspecialist.com/
http://www.techrestore.com/
In addition, if the port got burnt out by a storm surge or power surge your home/apartment insurance or credit card company you purchased the machine with may pay for the damage. So check each of those sources if you can't find an appropriate card.
http://www.xlr8yourmac.com/ lists a variety of upgrade cards in their database, and may have some ethernet cards you can look at.
By the way, the fact that port is broke suggests the possibility that any other system difficulty you are having may also be related to logicboard issue in anycase, so replacing the logicboard is a good idea if you are noticing other issues.
This thread may yield some clues:
http://macslash.org/article.pl?sid=05/11/09/2132230

Pcmcia ethernet card on compaq notebook

Hi can any one tell which Pcmcia ehrnet card supports for solaris x86 intel on notebook .....
I am using compaq presario1200 notebook and had netgearpc card which is not working with solaris 8
appreciated for the help

I finally got PCMCIA to work. But it was a battle.
My ethernet card DLINK DFE-690 TXD will NOT work with Arch 0.7. (It does work when using the Arch 0.7 Installation CD but after installation, it does not work).
I tried everything. (e.g. disabling almost everything in rc.conf and the config scripts). I even tried manually inserting the modules using modprobe. And then running dhcpcd. But dhcpcd failed since the ethernet PCMCIA card was "BUSY".
I found the BUG! The problem is with the 2.6.10 kernel that the arch 0.7 CD installs. In other words, the stock IDE or SCSI kernels that come with the 0.7 installation CD's are buggy.
I reinstalled arch usng FTP install. (arch 0.7.1 is then installed with a newer kernel 2.6.13). Arch 0.7.1 was able to properly detect and setup my PCMCIA card and get networking going.
I did NOT enable the pcmcia or hotplug daemons in rc.conf. You do NOT need to. They automatically get set up in the loadng modules stage (where some auto detection is being done).
So if anyone else is having problems, just use the FTP installation which installs arch 0.7.1 and a newer kernel 2.6.13.
Rob

PCMCIA Ethernet card for OS X 10.4.8 ?

My ethernet port on my Powerbook G4 is damaged and can no longer be used. I looked into getting it repaired but that apparently requires replacing the entire system board at considerable cost. Rather than take that route, I was hoping to find a PCMCIA card with an Ethernet port but I cannot seem to find any that will work with OS X 10.4.x.
Does anyone know of such a card ?
Thanks for your help !

So, these guys have nothing?
http://www.welovemacs.com/net-mpc-100.html
(MacSense PCMCIA 10/100 Ethernet Card)
This is one of the first things I found when I Googled before posting my original question.
But if you look towards the top of the page at this link under
System Requirements, you will see the following :
Supports Mac OS 7.5.3 and above (Excluding OSX support) G3 PowerBooks and above are not supported.
So, for my needs, yes, they have nothing.

Ethernet Card Problem

Hello,
I have a problem. I don't see my network adapter settings. Ethernet cable is working, I test it another PC. But this pc is not see adapter settings. That ethernet card will be lost I think. I just ask; It's operating system's problem or it's hardware problem, I do not know. How I test it?
(Please do not see my English grammar, it's not good I know)
This question was solved.
View Solution.

This is the HP Consumer support forum.
Your HP Pro desktop is a business class product.
That means you would be better served by joining the Business Enterprise forum and posting your question there.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

PCI Ethernet card problem.....please help!

Hi everyone, I intalled yesterday a PCI Ethernet card (10/100) on my PowerMac G5.
!0.5 immediately recogenize it and setted it with DHCP mode but internet looks to be slow so I chaged the configuration with static IP but with out any good result.
Internet works but very slooly while the network works great with (10/100 card and fine with integrated gigabit lan).
Someone could help me to understand while the PCI ethernet card doesn't work fine with internet? It's directly connected on a Netgear firewall routrer.....
thanks to everyone

But it could be unsupported the second ethernet on a powermac g5?
No, the fact that it shows up is proof that it works.
What Speeds are you getting with it?...
http://www.speakeasy.net/speedtest/
Also, in System Preferences>Network>Show>Ethernet 2>Ethernet tab>Configue:>Manually, try setting the speed lower & Duplex to Half-Duplex, restart required, test that setting.

2nd ethernet card problems

Hi all, I have an G4 MDD that I'm running 10.4 server and am trying to add a 2nd ethernet card to no avail. I tried adding a Dlink and then tried a Linksys card. Upon restarting from installing the drivers, both times I got a message stating that the install was not installed properly, and therefore the mac was not reading the card. Has anyone had this issue or any ideas. I am at a complete loss. Thanks.
-wes

There was an update to PCI ethernet controllers on
www.xlr8yourmac.com yesterday.
Were there drivers? did you repair permissions? did it complain that the extension or startupitem needed to be 'fixed?'
When adding or removing a PCI card, I have never seen or had the need to reset PMU. but I have and do need to reset nvram and insure nvram is current and the device tree is rebuilt.
I've also read of complaints about D-Link, mostly routers lately.

Pcmcia bluetooth card problem

OK, I have a bluetooth (bt) mouse, and two bt adapters. One adapter is usb and it works perfectly i.e. my bt mouse connects to it no probs. The other adaptor I have is pcmcia, which doesnt 'work'.
Here is the result of: udevinfo -a -p /sys/bus/pcmcia/devices/1.0
looking at device '/devices/pci0000:00/0000:00:1e.0/0000:02:01.1/1.0':
KERNEL=="1.0"
SUBSYSTEM=="pcmcia"
DRIVER=="serial_cs"
ATTR{modalias}=="pcmcia:m0279c950Bf02fn00pfn00pa281F1C5Dpb7664FB1Dpc00000000pd00000000"
ATTR{prod_id2}=="Bluetooth Card"
ATTR{prod_id1}=="PCMCIA"
ATTR{card_id}=="0x950b"
ATTR{manf_id}=="0x0279"
ATTR{func_id}=="0x02"
ATTR{pm_state}=="on"
ATTR{function}=="0x00"
So udev finds it and knows what it is no probs. However, hidd --search does absolutely nothing:
>hidd --search
searching ...
>
i.e. after the hidd command it prints searching and immediately goes back to a command prompt. Its not actually doing anything. I run kde and kbluetooth doesnt register that a bluetooth adapter is present at all.
looking back at the udevinfo output I think the driver thats being assigned is worng. As far as I understand the serial_cs driver is for pcmcia modems. Under suse 10.1 my pcmcia bt adapter works perfectly but udevinfo shows that the driver is "yenta_cardbus"
can anyone explain how I could force the driver used for my pcmcia bt adapter under arch to be "yenta_cardbus" or otherwise enlighten me as to what my problem might be.
Thanks

I called it
05-bluez-pcmcia-support.rules
I rebooted but still no success.
I also tried this:
ACTION=="add", SUBSYSTEMS=="pcmcia", ATTRS{prod_id2}=="Bluetooth Card", RUN+="aplay /usr/share/sounds/phone.wav"
But still no success

PCMCIA ethernet card (wired) that will work with 10.4 tiger?

i have unfortunately fried my ethernet port on my 1.33 al powerbook (applecare expired). I must use an ethernet PC adapter card that will work with Tiger 10.4.
The Dlink adapter although mention OSX support only works until 10.3.9.
Anyone here got suggestions as to which PC card to get?

Check Cisco. Also Google your need, i.e. "ethernet pc card and Mac". You should be able to research from there.

[solved]PCMCIA wired ethernet card issues

I have a Trendnet TE100-PCBUSR ethernet card plugged in to the PCMCIA socket on my dell laptop. I am trying to get it to connect through DHCP so that I can use pacman to install the programs I need, at the moment I only have the base packages. Google reveals to me that the ethernet card is a cardbus clone, and that it is supported by the tulip driver.
I installed arch by booting the cd and doing an ftp-based installation with the very same pcmcia ethernet card. Unfortunately after the installation I appear to not be connected to my network when my computer boots. To me, this says that I have simple configuration problems.
When I was running the installation, I got the card to work by doing these commands:
modprobe yenta_socket
modprobe tulip
the installer also advised that I run cardmgr, which told me there was no driver in /proc/devices, this warning didnt prevent the network from connecting to the ftp and downloading though. After running the modprobe commands I was able to establish a connection by using the menu in the installer.
My question is, how does the connection I made while running the installer translate into config files that can connect while booting? I am also wondering about that cardmgr error, is this something I should be worrying about?
I am looking forward to getting pacman working so that I can finaly have a linux that is bloat-free, containing only the stuff that I actually use. Even slackware handled configuring this card for me, so doing this by hand is new terriroty for me, when the system boots the card lights up like it did when I ran the modprobe commands, but I can't ping anything and pacman cannot download any packages.
You guys have already helped me alot at the IRC channel by helping with installing whenever I got stuck on some things. I imagine this is a simple issue that is documented somewhere, but I have not yet found this document and have been sitting on this problem for 2 days now. I would appreciate any clues you all could give me.

Here is the info you requested:
# /etc/rc.conf - Main Configuration for Arch Linux
# Localization
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/unimaps
# USECOLOR: use ANSI color sequences in startup messages
HARDWARECLOCK="localtime"
TIMEZONE=Canada/Pacific
KEYMAP=us
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# Networking
HOSTNAME="myhost"
# Module to load at boot-up (in this order)
# (prefix a module with a ! to disable it)
MODULES=(!usbserial !ide-scsi)
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# (prefix an interface in INTERFACES with a ! to disable it)
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
eth0="dhcp"
INTERFACES=(lo eth0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# (prefix a route in ROUTES with a ! to disable it)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Daemons to start at boot-up (in this order)
# (prefix a daemon with a ! to disable it)
# (prefix a daemon with a @ to start it up in the background)
DAEMONS=(syslog-ng hotplug pcmcia network netfs crond)
# End of file
Module Size Used by
pcmcia 28304 4
ohci_hcd 23044 0
ehci_hcd 37256 0
parport_pc 29124 0
parport 38600 1 parport_pc
pcspkr 4172 0
eth1394 21256 0
8139too 28032 0
ohci1394 36404 0
ieee1394 106200 2 eth1394,ohci1394
yenta_socket 23816 3
rsrc_nonstatic 14208 1 yenta_socket
pcmcia_core 52228 3 pcmcia,yenta_socket,rsrc_nonstatic
3c59x 42792 0
mii 6272 2 8139too,3c59x
snd_intel8x0m 20164 0
snd_intel8x0 34752 0
snd_ac97_codec 83960 2 snd_intel8x0m,snd_intel8x0
snd_pcm_oss 55456 0
snd_mixer_oss 20480 1 snd_pcm_oss
snd_pcm 97796 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 27012 1 snd_pcm
snd 60388 7
snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10848 1 snd
snd_page_alloc 10244 3 snd_intel8x0m,snd_intel8x0,snd_pcm
tpm_atmel 5376 0
tpm 12288 1 tpm_atmel
hw_random 5908 0
uhci_hcd 33808 0
pci_hotplug 30788 0
joydev 10688 0
tsdev 8384 0
evdev 10240 0
usbcore 127740 4 ohci_hcd,ehci_hcd,uhci_hcd
rtc 14156 0
00:00.0 Host bridge: Intel Corp.|82845 845 (Brookdale) Chipset Host Bridge (intel-agp)
00:01.0 PCI bridge: Intel Corp.|82845 845 (Brookdale) Chipset AGP Bridge (agpgart)
00:1d.0 USB Controller: Intel Corp.|82801 USB Controller (uhci_hcd)
00:1d.2 USB Controller: Intel Corp.|82801 USB Controller (uhci_hcd)
00:1e.0 PCI bridge: Intel Corp.|82801 Hub Interface to PCI Bridge (hw_random)
00:1f.0 ISA bridge: Intel Corp.|82801 LPC Interface (i810-tco)
00:1f.1 IDE interface: Intel Corp.|82801 UltraATA IDE Controller (piix)
00:1f.5 Multimedia audio controller: Intel Corp.|82801 AC97 Audio Controller
(i810_audio)
00:1f.6 Modem: Intel Corp.|PCTEL 2304 WT V.92 MDC Modem (slamr)
01:00.0 VGA compatible controller: nVidia Corp.|NV17M GeForce4 440 Go (nv)
02:00.0 Ethernet controller: 3Com Corp.|3c905C-TX [Fast Etherlink] (3c59x)
02:01.0 CardBus bridge: Texas Instruments|PCI4451 PC card Cardbus Controller
(yenta_socket)
02:01.1 CardBus bridge: Texas Instruments|PCI4451 PC card Cardbus Controller
(yenta_socket)
02:01.2 FireWire (IEEE 1394): Texas Instruments|PCI4451 OHCI-Lynx IEEE 1394
Controller (ohci1394)
07:00.0 Ethernet controller: Abocom Systems Inc|FE2000VX CardBus /Atelco Fibreline
Ethernet Adptr (8139too)
002:001 USB Hub: Virtual|Hub (hub)
001:001 USB Hub: Virtual|Hub (hub)
--:01.6 PCMCIA Network card: rdBus|Fast Ethernet (unknown)
---:--- Mouse: Generic PS/2 Wheel Mouse [/dev/psaux] (msintellips/2)
A little more info about my system, lshwd is detecting a built-in ethernet card that God decided to kill with a lighning bolt a couple years ago, the rest of the system still functions normally, my cable modem suffered the most from the strike and ended up getting replaced, but replacing an ethernet card built into this laptop is not possible because it is part of the main board, sigh.
I had a hell of a time transfering this data over, couldn't get the floppy to work so I installed pine and configured it to use my ISP email account, I royally messed up that config but strangely enough it still worked, the email came from [email protected], and I didnt have to login for it to work, which is lucky because I couldn't set up pine to do all that in the limited time I have with my machine.
Are you guys noticing a pattern yet? I can't configure very well, but I really hope to get better at it!
I also noticed that cardctl was telling me that my ethernet card is a cardbus fast ethernet, does that mean that I shouldnt be trying to use pcmcia-cs for this but use hotplug instead? lshwd also identified my ethernet card as something else, which I imagine is a card that my card is a clone of, since it appears to be working anyway.
I'm looking forward to your suggestions, any hints on configuring in general would be appreciated as well since I'm obviously having some bad luck with it I'll worry about floppy and email problems later.
PS: dhclient requires no parameters to connect, and I will have to give you my ifconfig info the next time I get a chance to use that computer.

Ethernet Card

Hello all,
I've inserted one PCMCIA ethernet card in a V440.
When I started the machine just only one port (the on board one) is shown with the ifconfig -a command.
So I created the others ports of the Ethe Card with the following command:
ifconfig ceX plumb
and then I added the IP to that port:
ifconfig ce1 172.17.0.58 netmask 255.255.255.0 up
So I tried to make a telnet to that IP, but it is not reachable. So I decided to reboot the machine. But when I made an ifconfig - a command after the reboot, all the port I've created disappeared and only ce0 is present, and also is present with another netmask.
Can anybody help me with this ?
Thks in advd
Sebastian

Hi,
Your machine is "HP Pavilion 15-e044sf". Please use the LAST document of the following link to get all part numbers of your machine:
http://support.hp.com/us-en/product/HP-Pavilion-15-Notebook-PC-series/5355006/model/5393818/manuals
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Dell Latitude CPx Xircom pcmcia card problem.

Hi.
I have recently received an old Dell Latitude CPx laptop. i have added to it an old Xircom RealPort CardBus Ethernet 10/100+ Modem 56.
after the installation,when booting, during the start-up of networking, i get the following message:
SIOCSIFFLAGS: Cannot assign requested address
are there any known solutions to this problem?
or will i have to swap Ethernet cards?
thank you in advance
sha1

1. Is the card recognized? Run lspci
2. What is the output of ifconfig -a? Does it show up as an interface?
3. Do you have it coming up by default in networking settings?

PCMCIA Realtek Ethernet card not detected

Hi, I'm trying to use a PCMCIA Etherner Card with Realtek chip.
If the card it's already plugged when booting, Udev takes 180000 ms to finish and the card doesn't work. If it's plugged while booted, dmesg shows that there's a "something" at SmartCardBus but, again, card doesn't get recognized.
"Ifconfig -a" shows nothing, and I know the card works 'cause I've tryed with an Ubuntu cd and the cards works perfect. I've looked for the modules, and 8139too & 8139cp where loaded, wich I've tryed in arch and still doesn't work, It also detects the same hardware with lspci (Arch detects the Cardbus but not the realtek card, Ubuntu detects both) and lspcmcia.
Ubuntu is using kernel 2.6.27-7 and Arch 2.6.28.
hwd -e:
1217:7113 CardBus bridge: 02 Micro, Inc. module:yanta_cardbus
OZ711EC1 SmartCardBus Controller
lspmcia:
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.0)
CardBus card -- see "lspci" for more information
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.1)
Socket 1 Device 0: [-- no driver --] (bus ID: 1.0)
lspci:
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250 [Mobility FireGL 9000] (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet (rev ff)
02:01.0 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:01.1 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:03.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
dmesg:
int3: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:03.0/class
Modules linked in: usb_storage joydev ppdev iTCO_wdt iTCO_vendor_support ehci_hcd psmouse uhci_hcd parport_pc lp serio_raw usbcore shpchp pci_hotplug sg video output parport pcspkr ppp_generic intel_agp agpgart pcmcia dcdbas thermal evdev fan button battery ac acpi_cpufreq freq_table processor snd_intel8x0m snd_seq_oss snd_intel8x0 snd_seq_midi_event snd_seq snd_seq_device snd_ac97_codec snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore ac97_bus ipw2200 ieee80211 ieee80211_crypt tg3 libphy slhc rtc_cmos rtc_core rtc_lib ext3 jbd mbcache sr_mod cdrom yenta_socket rsrc_nonstatic pcmcia_core sd_mod ata_piix ata_generic pata_acpi libata scsi_mod
Pid: 435, comm: pccardd Not tainted (2.6.28-ARCH #1) Inspiron 600m
EIP: 0060:[<c044dce0>] EFLAGS: 00000246 CPU: 0
EIP is at quirk_h12y_1_mmio+0x1/0x26
EAX: de4fc800 EBX: c03cbdc0 ECX: de4fc840 EDX: de4fc800
ESI: c03cc110 EDI: de4fc800 EBP: df8ae400 ESP: df1b9ef4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process pccardd (pid: 435, ti=df1b8000 task=df1ba000 task.ti=df1b8000)
Stack:
c02192c3 de4fc800 df8ae400 de4fc800 c0216a59 00000200 00000000 c031c93c
de4fc826 c03b3d25 00000000 00000003 00000000 00000000 00000001 df8ae420
de4fc858 00000200 813910ec 00ffffed 00000000 00000000 00000000 df8ae400
Call Trace:
[<c02192c3>] pci_fixup_device+0x63/0xc0
[<c0216a59>] pci_device_add+0x69/0xb0
[<c031c93c>] pci_scan_single_device+0x35c/0x4f0
[<c0216ac3>] pci_scan_slot+0x23/0x80
[<e0bd850f>] cb_alloc+0x1f/0xd4 [pcmcia_core]
[<e0bd4854>] socket_insert+0x124/0x140 [pcmcia_core]
[<e0bd5202>] pccardd+0x202/0x290 [pcmcia_core]
[<e0bd5000>] pccardd+0x0/0x290 [pcmcia_core]
[<c01440f9>] kthread+0x39/0x70
[<c01440c0>] kthread+0x0/0x70
[<c0104d33>] kernel_thread_helper+0x7/0x14
Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
EIP: [<c044dce0>] quirk_h12y_1_mmio+0x1/0x26 SS:ESP 0068:df1b9ef4
---[ end trace 6fe320c81d500dc7 ]---
note: pccardd[435] exited with preempt_count 1
pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
pci 0000:01:00.0: putting AGP V2 device into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
rc.conf:
MODULES=(slhc tg3 ipw2200 ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore acpi-cpufreq)
DAEMONS=(syslog-ng network netfs dbus hal !crond cpufreq fam avahi-daemon pcmcia)
I've tryed loading: 8139too 8139cp pcmcia_core pcmcia yenta_socket rsrc_nonstatic
The bradcom is the original eth port wich I'm replacing because stop working long time ago (And I also tryed disabling it from BIOS, and it's the same).
I'm mising something that I should load or run? I've googled a lot, but people just plug the card and that's all :-P. Any idea would be welcomed :-).
EDIT: Fix title (PMCIA*)
Last edited by el_zoona (2009-01-22 07:25:00)

Nevermind...It's Kernel 2.6.28...I'm a lucky guy, eh? :-(
Booted into Arch Overlod cd and a simple lspci show my shiny new card...Now i'm going to erase my hole system (it was new anyway) and check if a Suy breaks the drivers again. In that case, i should file a bug somewhere, right?

Merged Topics: 3C575 PCMCIA card problem, Solaris 10x86

Hi all, I had installed the solaris 10 x86 on my notebook, by it can not see my 3com 575 PCMCIA NIC card.
I had searched the internet,someone said sun will give the PCMCIA Driver in feture,but someone said it will not.
so , what can I do now? wait or give up ?

Hi all, I have a 3com 3CCFE575BT PCMCIA card on a solaris 10 notebook, but the solaris 10 did not detect the pc card, does anyone meet the same problem ?
I had installde the initpcic.pkg and the cardbus driver from
http://www.opensolaris.org,still did not see the card
#prtconf -D
System Configuration: Sun Microsystems i86pc
Memory size: 1016 Megabytes
System Peripherals (Software Nodes):
i86pc (driver name: rootnex)
scsi_vhci, instance #0 (driver name: scsi_vhci)
+boot<br />
memory
aliases
chosen
i86pc-memory
i86pc-mmu
openprom
options, instance #0 (driver name: options)
packages
delayed-writes
itu-props
isa, instance #0 (driver name: isa)
motherboard
i8042, instance #0 (driver name: i8042)
mouse, instance #0 (driver name: mouse8042)
keyboard, instance #0 (driver name: kb8042)
SMCF010
pci, instance #0 (driver name: pci)
pci1043,1882
display, instance #0 (driver name: vgatext)
pci1043,1882
pci1043,10c3
pci8086,2660, instance #0 (driver name: pci_pci)
pci1043,10e7, instance #0 (driver name: uhci)
mouse, instance #0 (driver name: hid)
pci1043,10e7, instance #1 (driver name: uhci)
pci1043,10e7, instance #2 (driver name: uhci)
pci1043,10e7, instance #3 (driver name: uhci)
pci1043,10e7, instance #0 (driver name: ehci)
pci8086,2448, instance #1 (driver name: pci_pci)
pci1043,173c, instance #0 (driver name: yukonx)
pci1043,1967, instance #0 (driver name: pcic)
pcs, instance #0 (driver name: pcs)
pci1043,1967, instance #0 (driver name: hci1394)
pci1043,1967
pci1043,1967
pci8086,2701
pci8086,2641
pci-ide, instance #0 (driver name: pci-ide)
ide, instance #0 (driver name: ata)
cmdk, instance #0 (driver name: cmdk)
ide, instance #1 (driver name: ata)
sd, instance #0 (driver name: sd)
pci1043,10e7
used-resources
pseudo, instance #0 (driver name: pseudo)
xsvc, instance #0 (driver name: xsvc)
objmgr, instance #0 (driver name: objmgr)
cpus
cpu, instance #0
#prtconf -D | grep pcic
pci1043,1967, instance #0 (driver name: pcic)
please help me. where is the problem ?

Xircom pcmcia ethernet card problem.

Similar Messages

Maybe you are looking for