Xorg configuration with nvidia 6800gs agp and flatron l222wt

my computer is set to run with a l222wt lcd monitor with a 1680x1050 native resolution on a nvidia 6800gs vid card through a analog port.  for wutever reason, my video settings are no longer being detected by xorg anymore after i install xorg and the nvidia driver.  my last arch linux install was fine (i had been using a standard crt at 1280x1024) and when i switched monitors it autodetected the resolution.  however, when i went to reinstall linux, it no longer autodetected and i got horrible settings.  i tried to use the mode setting under the display subsection to set my resolutiona dn still no go.  is their any better way to force it to use my preffered resolution?
thanks
Grama
Last edited by Grama (2008-04-13 19:37:54)

well all is working now.... i had not ever edited resolutions using the modeline in the monitor section.... all i needed to do was enter my correct modeline settings and bango correct
as for the ftp install problem i just burned the new 2008.04rc i686 iso and like the arch linux of old it worked once more
thanks
Grama

Similar Messages

  • I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

    I have a problem with Mail on my Macbook Pro. It is configurated with a gmail account, and now I can't access the mail. Is it possible to reboot the account or..? Please help:)

    The question mark means the computer cannot find a bootable volumes so can;t do anything, That, combined with annoying sounds, strongly suggests a failed hard drive.
    You can ask a "genius" at an Apple Rtail Store to test it but I'm pretty sure the drive is kaput. I'm hoping you had your data backed up.

  • GPU lock up with nvidia GeForce4 MX and nouveau driver

    hello
    getting a "GPU lock out" message when booting Arch - Geforce4 MX 64mb card
    extract from dmseg:-
    [   24.175980] [TTM] Initializing pool allocator
    [   24.176007] [drm] nouveau 0000:01:00.0: Detected 64MiB VRAM (DDR1)
    [   24.176569] agpgart-intel 0000:00:00.0: AGP 2.0 bridge
    [   24.176598] agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
    [   24.176638] nouveau 0000:01:00.0: putting AGP V2 device into 4x mode
    [   24.176735] [drm] nouveau 0000:01:00.0: 128 MiB GART (aperture)
    [   24.176831] [drm] nouveau 0000:01:00.0: Saving VGA fonts
    [   24.235131] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [   24.235137] [drm] No driver support for vblank timestamp query.
    [   24.240867] [drm] nouveau 0000:01:00.0: 1 available performance level(s)
    [   24.240874] [drm] nouveau 0000:01:00.0: 0: memory 270MHz
    [   24.240879] [drm] nouveau 0000:01:00.0: c: core 249MHz memory 279MHz
    [   24.242940] [drm] nouveau 0000:01:00.0: 0xE72C: Parsing digital output script table
    [   24.265606] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on vga encoder (output 0)
    [   24.265613] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on tmds encoder (output 1)
    [   24.265619] [drm] nouveau 0000:01:00.0: Setting dpms mode 3 on TV encoder (output 2)
    [   24.344176] [drm] nouveau 0000:01:00.0: allocated 1280x1024 fb: 0x49000, bo f5859e00
    [   24.344385] fbcon: nouveaufb (fb0) is primary device
    [   24.368223] [drm] nouveau 0000:01:00.0: Setting dpms mode 0 on vga encoder (output 0)
    [   24.368232] [drm] nouveau 0000:01:00.0: Output VGA-1 is running on CRTC 0 using output A
    [   24.403590] firewire_core 0000:04:0c.0: created device fw0: GUID 805b0600a8678400, S400
    [   24.447427] [drm] nouveau 0000:01:00.0: GPU lockup - switching to software fbcon
    [   24.451362] Console: switching to colour frame buffer device 160x64
    [   24.458961] fb0: nouveaufb frame buffer device
    [   24.458965] drm: registered panic notifier
    [   24.458975] [drm] Initialized nouveau 1.0.0 20120316 for 0000:01:00.0 on minor 0
    [   24.593364] intel8x0_measure_ac97_clock: measured 50169 usecs (2810 samples)
    [   24.593371] intel8x0: clocking to 41135
    [   26.447145] EXT4-fs (sdc3): re-mounted. Opts: (null)
    [   26.543027] EXT4-fs (sdc1): mounting ext2 file system using the ext4 subsystem
    [   26.551916] EXT4-fs (sdc1): mounted filesystem without journal. Opts: (null)
    [   26.552444] EXT4-fs (sda1): mounting ext3 file system using the ext4 subsystem
    [   26.584073] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    [   26.664062] Adding 530140k swap on /dev/sdc2.  Priority:-1 extents:1 across:530140k
    Does anyone know if this looks like a hardware issue or a driver (drm) probelm? Very old card so sort of expecting it to be hardware related.
    Strangely I can clear the problem and get into X by fsking the discs from Ubuntu recovery console (dual booting the two) - just thinking whether there's a lock file somewhere not getting cleaned up or something?

    I confirm this. I have the same card (NV17 [GeForce4 MX 440]), and I get random lockups with the nouveau driver and a recent kernel. It's probably a memory handling problem in the DRM driver.

  • Automatic monitor calibration with NVidia GT 120 and ATI 4870

    I am considering purchase of a Mac Pro to use with a LaCie monitor and the Blue Eye Pro calibrator / software. Auto calibration of the monitor is possible if the calibrator / software can communicate directly via the graphics cards with the monitor. DDC CI - a communication standard is used for this. My question is are these cards able to use this standard.
    I have tried Apple Service and Support by telephone and I have tried to find information on the NVidia and ATI websites without success. Neither site seems to provide a way to email such a question to them.
    I am surprised that Apple are unable to provide information of this type to help a prospective purchaser.
    Has anyone any advice or or experience to offer me - it would be gratefully received!

    Have you asked Blu Eye?

  • [SOLVED] Xorg freeze with nvidia GeForce 210 when resizing terminal

    Hello,
    I am working on Archlinux. My computer freeze when I resize a terminal window.
    To reproduce the problem, I follow the below steps :
         1- launch openbox (with tint2, xcompmgr and nitrogen)
         2- start the "terminal" console emulator (with true transparent background)
         3- launch opera and go to a website which take a while to load (with a lot of data) (I used http://www.lemonde.fr)
         4- while the website is loading, switch to the terminal window and double click on the title bar to maximize it
         5- the box freeze
    I am not able to take the control back. I cannot exit or kill Xorg / Openbox. I cannot switch to a text terminal (ttyx). No key sequence is working.
    Only a hard reset of the box is working.
    I have tried to disable the transparent background of the terminal window without success.
    I have tried to not start xcompmgr without success.
    The problem also occurs with rxvt-unicode instead of terminal.
    It seems the problem happens more often when using console emulator based on vte.
    vte itself has the same issue.
    The only workaround I have found is to disable the harware acceleration with the below parameter in the xorg.conf file:
    Option    "RenderAccel"    "true"
    The problem with this workaround are poor graphical performances.
    Could you please let me know if you have any idea / clue to identify / fix this problem ?
    Thanks and regards
    uname -a
    Linux myhost 2.6.38-ARCH #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011 i686 Intel(R) Core(TM)2 Duo CPU E7600 @ 3.06GHz GenuineIntel GNU/Linux
    versions
    nvidia 270.41.06-1
    nvidia-utils 270.41.06-1
    kernel26 2.6.38.4-1
    openbox 3.4.11.2-2
    xcompmgr 1.1.5-1
    .xinitrc
    #!/bin/sh
    # ~/.xinitrc
    # Executed by startx (run your window manager from here)
    if [ -d /etc/X11/xinit/xinitrc.d ]; then
    for f in /etc/X11/xinit/xinitrc.d/*; do
    [ -x "$f" ] && . "$f"
    done
    unset f
    fi
    # exec gnome-session
    # exec startkde
    # exec startxfce4
    # ...or the Window Manager of your choice
    exec ck-launch-session openbox-session
    .config/openbox/autostart.sh
    # This shell script is run before Openbox launches.
    # Environment variables set here are passed to the Openbox session.
    # Set a background color
    BG=""
    if which hsetroot >/dev/null 2>&1; then
    BG=hsetroot
    else
    if which esetroot >/dev/null 2>&1; then
    BG=esetroot
    else
    if which xsetroot >/dev/null 2>&1; then
    BG=xsetroot
    fi
    fi
    fi
    test -z $BG || $BG -solid "#303030"
    # D-bus
    if which dbus-launch >/dev/null 2>&1 && test -z "$DBUS_SESSION_BUS_ADDRESS"; then
    eval `dbus-launch --sh-syntax --exit-with-session`
    fi
    # Make GTK apps look and behave how they were set up in the gnome config tools
    if test -x /usr/libexec/gnome-settings-daemon >/dev/null; then
    /usr/libexec/gnome-settings-daemon &
    elif which gnome-settings-daemon >/dev/null 2>&1; then
    gnome-settings-daemon &
    # Make GTK apps look and behave how they were set up in the XFCE config tools
    elif which xfce-mcs-manager >/dev/null 2>&1; then
    xfce-mcs-manager n &
    fi
    # Preload stuff for KDE apps
    if which start_kdeinit >/dev/null 2>&1; then
    LD_BIND_NOW=true start_kdeinit --new-startup +kcminit_startup &
    fi
    # Run XDG autostart things. By default don't run anything desktop-specific
    # See xdg-autostart --help more info
    DESKTOP_ENV="OPENBOX"
    if which /usr/lib/openbox/xdg-autostart >/dev/null 2>&1; then
    /usr/lib/openbox/xdg-autostart $DESKTOP_ENV
    fi
    xcompmgr &
    nitrogen --set-zoom-fill /mnt/data/pictures/flower.jpg &
    tint2 &
    xorg.conf
    Section "ServerLayout"
    Identifier "X.org Configured"
    Screen 0 "Screen0" 0 0
    InputDevice "Mouse0" "CorePointer"
    InputDevice "Keyboard0" "CoreKeyboard"
    EndSection
    Section "Files"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc/"
    FontPath "/usr/share/fonts/TTF/"
    FontPath "/usr/share/fonts/OTF/"
    FontPath "/usr/share/fonts/Type1/"
    FontPath "/usr/share/fonts/100dpi/"
    FontPath "/usr/share/fonts/75dpi/"
    EndSection
    Section "Module"
    Load "extmod"
    Load "glx"
    Load "record"
    Load "dbe"
    Load "dri2"
    EndSection
    Section "InputClass"
    Identifier "Keyboard Defaults"
    MatchIsKeyboard "yes"
    Option "XkbLayout" "fr"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/input/mice"
    Option "ZAxisMapping" "4 5 6 7"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Device"
    Identifier "Card0"
    Driver "nvidia"
    Option "RenderAccel" "true"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Card0"
    Monitor "Monitor0"
    SubSection "Display"
    Viewport 0 0
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Section "Extensions"
    Option "Composite" "Enable"
    EndSection
    Xorg.0.log
    [ 485.566]
    X.Org X Server 1.10.1
    Release Date: 2011-04-15
    [ 485.566] X Protocol Version 11, Revision 0
    [ 485.566] Build Operating System: Linux 2.6.38-ARCH i686
    [ 485.566] Current Operating System: Linux myhost 2.6.38-ARCH #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011 i686
    [ 485.566] Kernel command line: root=/dev/sda3 ro
    [ 485.566] Build Date: 16 April 2011 12:05:35PM
    [ 485.566]
    [ 485.566] Current version of pixman: 0.20.2
    [ 485.567] Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    [ 485.567] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 485.567] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 27 20:00:28 2011
    [ 485.567] (==) Using config file: "/etc/X11/xorg.conf"
    [ 485.568] (==) Using config directory: "/etc/X11/xorg.conf.d"
    [ 485.568] (==) ServerLayout "X.org Configured"
    [ 485.568] (**) |-->Screen "Screen0" (0)
    [ 485.568] (**) | |-->Monitor "Monitor0"
    [ 485.568] (**) | |-->Device "Card0"
    [ 485.568] (**) |-->Input Device "Mouse0"
    [ 485.568] (**) |-->Input Device "Keyboard0"
    [ 485.568] (==) Automatically adding devices
    [ 485.568] (==) Automatically enabling devices
    [ 485.568] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 485.568] Entry deleted from font path.
    [ 485.568] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
    [ 485.568] Entry deleted from font path.
    [ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 485.568] Entry deleted from font path.
    [ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 485.568] Entry deleted from font path.
    [ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 485.568] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 485.568] Entry deleted from font path.
    [ 485.568] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
    [ 485.568] Entry deleted from font path.
    [ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
    [ 485.568] Entry deleted from font path.
    [ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
    [ 485.568] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
    [ 485.568] Entry deleted from font path.
    [ 485.568] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
    [ 485.568] (**) FontPath set to:
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/,
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/
    [ 485.568] (**) ModulePath set to "/usr/lib/xorg/modules"
    [ 485.568] (**) Extension "Composite" is enabled
    [ 485.568] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
    [ 485.568] (WW) Disabling Mouse0
    [ 485.568] (WW) Disabling Keyboard0
    [ 485.568] (II) Loader magic: 0x81f4ee0
    [ 485.568] (II) Module ABI versions:
    [ 485.568] X.Org ANSI C Emulation: 0.4
    [ 485.568] X.Org Video Driver: 10.0
    [ 485.568] X.Org XInput driver : 12.2
    [ 485.568] X.Org Server Extension : 5.0
    [ 485.569] (--) PCI:*(0:1:0:0) 10de:0a65:1043:8334 rev 162, Mem @ 0xfa000000/16777216, 0xd0000000/268435456, 0xce000000/33554432, I/O @ 0x0000bc00/128, BIOS @ 0x????????/524288
    [ 485.569] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    [ 485.569] (II) "extmod" will be loaded. This was enabled by default and also specified in the config file.
    [ 485.569] (II) "dbe" will be loaded. This was enabled by default and also specified in the config file.
    [ 485.569] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
    [ 485.569] (II) "record" will be loaded. This was enabled by default and also specified in the config file.
    [ 485.569] (II) "dri" will be loaded by default.
    [ 485.569] (II) "dri2" will be loaded. This was enabled by default and also specified in the config file.
    [ 485.569] (II) LoadModule: "extmod"
    [ 485.569] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    [ 485.569] (II) Module extmod: vendor="X.Org Foundation"
    [ 485.569] compiled for 1.10.1, module version = 1.0.0
    [ 485.569] Module class: X.Org Server Extension
    [ 485.569] ABI class: X.Org Server Extension, version 5.0
    [ 485.569] (II) Loading extension MIT-SCREEN-SAVER
    [ 485.569] (II) Loading extension XFree86-VidModeExtension
    [ 485.569] (II) Loading extension XFree86-DGA
    [ 485.569] (II) Loading extension DPMS
    [ 485.569] (II) Loading extension XVideo
    [ 485.569] (II) Loading extension XVideo-MotionCompensation
    [ 485.569] (II) Loading extension X-Resource
    [ 485.569] (II) LoadModule: "glx"
    [ 485.569] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 485.588] (II) Module glx: vendor="NVIDIA Corporation"
    [ 485.588] compiled for 4.0.2, module version = 1.0.0
    [ 485.589] Module class: X.Org Server Extension
    [ 485.589] (II) NVIDIA GLX Module 270.41.06 Mon Apr 18 15:11:28 PDT 2011
    [ 485.589] (II) Loading extension GLX
    [ 485.589] (II) LoadModule: "record"
    [ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    [ 485.589] (II) Module record: vendor="X.Org Foundation"
    [ 485.589] compiled for 1.10.1, module version = 1.13.0
    [ 485.589] Module class: X.Org Server Extension
    [ 485.589] ABI class: X.Org Server Extension, version 5.0
    [ 485.589] (II) Loading extension RECORD
    [ 485.589] (II) LoadModule: "dbe"
    [ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    [ 485.589] (II) Module dbe: vendor="X.Org Foundation"
    [ 485.589] compiled for 1.10.1, module version = 1.0.0
    [ 485.589] Module class: X.Org Server Extension
    [ 485.589] ABI class: X.Org Server Extension, version 5.0
    [ 485.589] (II) Loading extension DOUBLE-BUFFER
    [ 485.589] (II) LoadModule: "dri2"
    [ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    [ 485.589] (II) Module dri2: vendor="X.Org Foundation"
    [ 485.589] compiled for 1.10.1, module version = 1.2.0
    [ 485.589] ABI class: X.Org Server Extension, version 5.0
    [ 485.589] (II) Loading extension DRI2
    [ 485.589] (II) LoadModule: "dri"
    [ 485.589] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    [ 485.589] (II) Module dri: vendor="X.Org Foundation"
    [ 485.589] compiled for 1.10.1, module version = 1.0.0
    [ 485.589] ABI class: X.Org Server Extension, version 5.0
    [ 485.589] (II) Loading extension XFree86-DRI
    [ 485.589] (II) LoadModule: "nvidia"
    [ 485.589] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    [ 485.590] (II) Module nvidia: vendor="NVIDIA Corporation"
    [ 485.590] compiled for 4.0.2, module version = 1.0.0
    [ 485.590] Module class: X.Org Video Driver
    [ 485.590] (II) NVIDIA dlloader X Driver 270.41.06 Mon Apr 18 14:55:51 PDT 2011
    [ 485.590] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
    [ 485.590] (--) using VT number 7
    [ 485.593] (II) Loading sub module "fb"
    [ 485.593] (II) LoadModule: "fb"
    [ 485.593] (II) Loading /usr/lib/xorg/modules/libfb.so
    [ 485.593] (II) Module fb: vendor="X.Org Foundation"
    [ 485.593] compiled for 1.10.1, module version = 1.0.0
    [ 485.593] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 485.593] (II) Loading sub module "wfb"
    [ 485.593] (II) LoadModule: "wfb"
    [ 485.593] (II) Loading /usr/lib/xorg/modules/libwfb.so
    [ 485.593] (II) Module wfb: vendor="X.Org Foundation"
    [ 485.593] compiled for 1.10.1, module version = 1.0.0
    [ 485.593] ABI class: X.Org ANSI C Emulation, version 0.4
    [ 485.593] (II) Loading sub module "ramdac"
    [ 485.593] (II) LoadModule: "ramdac"
    [ 485.593] (II) Module "ramdac" already built-in
    [ 485.593] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    [ 485.593] (II) Loading /usr/lib/xorg/modules/libwfb.so
    [ 485.593] (II) Loading /usr/lib/xorg/modules/libfb.so
    [ 485.593] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
    [ 485.593] (==) NVIDIA(0): RGB weight 888
    [ 485.593] (==) NVIDIA(0): Default visual is TrueColor
    [ 485.593] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
    [ 485.593] (**) NVIDIA(0): Option "RenderAccel" "true"
    [ 485.593] (**) NVIDIA(0): Enabling RENDER acceleration
    [ 485.953] (II) NVIDIA(GPU-0): Display (LG Electronics L222W (CRT-0)) does not support NVIDIA
    [ 485.953] (II) NVIDIA(GPU-0): 3D Vision stereo.
    [ 485.986] (II) NVIDIA(GPU-0): Display (PANASONIC-TV (DFP-1)) does not support NVIDIA 3D
    [ 485.986] (II) NVIDIA(GPU-0): Vision stereo.
    [ 485.987] (II) NVIDIA(0): NVIDIA GPU GeForce 210 (GT218) at PCI:1:0:0 (GPU-0)
    [ 485.987] (--) NVIDIA(0): Memory: 1048576 kBytes
    [ 485.987] (--) NVIDIA(0): VideoBIOS: 70.18.39.00.17
    [ 485.987] (II) NVIDIA(0): Detected PCI Express Link width: 16X
    [ 485.987] (--) NVIDIA(0): Interlaced video modes are supported on this GPU
    [ 485.987] (--) NVIDIA(0): Connected display device(s) on GeForce 210 at PCI:1:0:0
    [ 485.987] (--) NVIDIA(0): LG Electronics L222W (CRT-0)
    [ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1)
    [ 485.987] (--) NVIDIA(0): LG Electronics L222W (CRT-0): 400.0 MHz maximum pixel clock
    [ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1): 165.0 MHz maximum pixel clock
    [ 485.987] (--) NVIDIA(0): PANASONIC-TV (DFP-1): Internal Single Link TMDS
    [ 486.026] (II) NVIDIA(0): Assigned Display Device: CRT-0
    [ 486.026] (==) NVIDIA(0):
    [ 486.026] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
    [ 486.026] (==) NVIDIA(0): will be used as the requested mode.
    [ 486.026] (==) NVIDIA(0):
    [ 486.026] (II) NVIDIA(0): Validated modes:
    [ 486.026] (II) NVIDIA(0): "nvidia-auto-select"
    [ 486.026] (II) NVIDIA(0): Virtual screen size determined to be 1680 x 1050
    [ 486.054] (--) NVIDIA(0): DPI set to (90, 88); computed from "UseEdidDpi" X config
    [ 486.054] (--) NVIDIA(0): option
    [ 486.054] (--) Depth 24 pixmap format is 32 bpp
    [ 486.054] (II) NVIDIA: Using 768.00 MB of virtual memory for indirect memory access.
    [ 486.056] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
    [ 486.056] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
    [ 486.056] (II) NVIDIA(0): configuration option may not be set correctly. When the
    [ 486.056] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
    [ 486.056] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
    [ 486.056] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
    [ 486.056] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
    [ 486.056] (II) NVIDIA(0): Config Options in the README.
    [ 486.058] (II) NVIDIA(0): Setting mode "nvidia-auto-select"
    [ 486.286] (II) Loading extension NV-GLX
    [ 486.314] (==) NVIDIA(0): Disabling shared memory pixmaps
    [ 486.314] (==) NVIDIA(0): Backing store disabled
    [ 486.314] (==) NVIDIA(0): Silken mouse enabled
    [ 486.314] (==) NVIDIA(0): DPMS enabled
    [ 486.314] (II) Loading extension NV-CONTROL
    [ 486.315] (II) Loading extension XINERAMA
    [ 486.315] (II) Loading sub module "dri2"
    [ 486.315] (II) LoadModule: "dri2"
    [ 486.315] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    [ 486.315] (II) Module dri2: vendor="X.Org Foundation"
    [ 486.315] compiled for 1.10.1, module version = 1.2.0
    [ 486.315] ABI class: X.Org Server Extension, version 5.0
    [ 486.315] (II) NVIDIA(0): [DRI2] Setup complete
    [ 486.315] (==) RandR enabled
    [ 486.315] (II) Initializing built-in extension Generic Event Extension
    [ 486.315] (II) Initializing built-in extension SHAPE
    [ 486.315] (II) Initializing built-in extension MIT-SHM
    [ 486.315] (II) Initializing built-in extension XInputExtension
    [ 486.315] (II) Initializing built-in extension XTEST
    [ 486.315] (II) Initializing built-in extension BIG-REQUESTS
    [ 486.315] (II) Initializing built-in extension SYNC
    [ 486.315] (II) Initializing built-in extension XKEYBOARD
    [ 486.315] (II) Initializing built-in extension XC-MISC
    [ 486.315] (II) Initializing built-in extension SECURITY
    [ 486.315] (II) Initializing built-in extension XINERAMA
    [ 486.315] (II) Initializing built-in extension XFIXES
    [ 486.315] (II) Initializing built-in extension RENDER
    [ 486.315] (II) Initializing built-in extension RANDR
    [ 486.315] (II) Initializing built-in extension COMPOSITE
    [ 486.315] (II) Initializing built-in extension DAMAGE
    [ 486.317] (II) Initializing extension GLX
    [ 486.364] (II) config/udev: Adding input device Power Button (/dev/input/event1)
    [ 486.364] (**) Power Button: Applying InputClass "evdev keyboard catchall"
    [ 486.364] (**) Power Button: Applying InputClass "Keyboard Defaults"
    [ 486.364] (II) LoadModule: "evdev"
    [ 486.365] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.365] (II) Module evdev: vendor="X.Org Foundation"
    [ 486.365] compiled for 1.10.0, module version = 2.6.0
    [ 486.365] Module class: X.Org XInput Driver
    [ 486.365] ABI class: X.Org XInput driver, version 12.2
    [ 486.365] (II) Using input driver 'evdev' for 'Power Button'
    [ 486.365] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.365] (**) Power Button: always reports core events
    [ 486.365] (**) Power Button: Device: "/dev/input/event1"
    [ 486.376] (--) Power Button: Found keys
    [ 486.376] (II) Power Button: Configuring as keyboard
    [ 486.376] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1/event1"
    [ 486.376] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
    [ 486.376] (**) Option "xkb_rules" "evdev"
    [ 486.376] (**) Option "xkb_model" "evdev"
    [ 486.376] (**) Option "xkb_layout" "fr"
    [ 486.397] (II) config/udev: Adding input device Power Button (/dev/input/event0)
    [ 486.397] (**) Power Button: Applying InputClass "evdev keyboard catchall"
    [ 486.397] (**) Power Button: Applying InputClass "Keyboard Defaults"
    [ 486.397] (II) Using input driver 'evdev' for 'Power Button'
    [ 486.397] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.397] (**) Power Button: always reports core events
    [ 486.397] (**) Power Button: Device: "/dev/input/event0"
    [ 486.413] (--) Power Button: Found keys
    [ 486.413] (II) Power Button: Configuring as keyboard
    [ 486.413] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0/event0"
    [ 486.413] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD)
    [ 486.413] (**) Option "xkb_rules" "evdev"
    [ 486.413] (**) Option "xkb_model" "evdev"
    [ 486.413] (**) Option "xkb_layout" "fr"
    [ 486.415] (II) config/udev: Adding input device HDA Digital PCBeep (/dev/input/event2)
    [ 486.415] (II) No input driver/identifier specified (ignoring)
    [ 486.418] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event3)
    [ 486.418] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
    [ 486.418] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
    [ 486.418] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
    [ 486.418] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.418] (**) Microsoft Wired Keyboard 600: always reports core events
    [ 486.418] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event3"
    [ 486.430] (--) Microsoft Wired Keyboard 600: Found keys
    [ 486.430] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
    [ 486.430] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-1/9-1:1.0/input/input3/event3"
    [ 486.430] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
    [ 486.430] (**) Option "xkb_rules" "evdev"
    [ 486.430] (**) Option "xkb_model" "evdev"
    [ 486.430] (**) Option "xkb_layout" "fr"
    [ 486.430] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/event4)
    [ 486.430] (**) Microsoft Wired Keyboard 600: Applying InputClass "evdev keyboard catchall"
    [ 486.430] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
    [ 486.430] (II) Using input driver 'evdev' for 'Microsoft Wired Keyboard 600'
    [ 486.430] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.430] (**) Microsoft Wired Keyboard 600: always reports core events
    [ 486.430] (**) Microsoft Wired Keyboard 600: Device: "/dev/input/event4"
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found 1 mouse buttons
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found scroll wheel(s)
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found relative axes
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found absolute axes
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found x and y absolute axes
    [ 486.446] (--) Microsoft Wired Keyboard 600: Found keys
    [ 486.446] (II) Microsoft Wired Keyboard 600: Configuring as mouse
    [ 486.446] (II) Microsoft Wired Keyboard 600: Configuring as keyboard
    [ 486.446] (II) Microsoft Wired Keyboard 600: Adding scrollwheel support
    [ 486.446] (**) Microsoft Wired Keyboard 600: YAxisMapping: buttons 4 and 5
    [ 486.446] (**) Microsoft Wired Keyboard 600: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 486.446] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-1/9-1:1.1/input/input4/event4"
    [ 486.446] (II) XINPUT: Adding extended input device "Microsoft Wired Keyboard 600" (type: KEYBOARD)
    [ 486.446] (**) Option "xkb_rules" "evdev"
    [ 486.446] (**) Option "xkb_model" "evdev"
    [ 486.446] (**) Option "xkb_layout" "fr"
    [ 486.447] (EE) Microsoft Wired Keyboard 600: failed to initialize for relative axes.
    [ 486.447] (WW) Microsoft Wired Keyboard 600: found 37 axes, limiting to 36.
    [ 486.447] (II) Microsoft Wired Keyboard 600: initialized for absolute axes.
    [ 486.447] (**) Microsoft Wired Keyboard 600: (accel) keeping acceleration scheme 1
    [ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration profile 0
    [ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration factor: 2.000
    [ 486.447] (**) Microsoft Wired Keyboard 600: (accel) acceleration threshold: 4
    [ 486.447] (II) config/udev: Adding input device Microsoft Wired Keyboard 600 (/dev/input/js0)
    [ 486.447] (**) Microsoft Wired Keyboard 600: Applying InputClass "Keyboard Defaults"
    [ 486.447] (II) No input driver/identifier specified (ignoring)
    [ 486.447] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/event5)
    [ 486.447] (**) Logitech USB Optical Mouse: Applying InputClass "evdev pointer catchall"
    [ 486.447] (II) Using input driver 'evdev' for 'Logitech USB Optical Mouse'
    [ 486.447] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
    [ 486.447] (**) Logitech USB Optical Mouse: always reports core events
    [ 486.447] (**) Logitech USB Optical Mouse: Device: "/dev/input/event5"
    [ 486.473] (--) Logitech USB Optical Mouse: Found 12 mouse buttons
    [ 486.473] (--) Logitech USB Optical Mouse: Found scroll wheel(s)
    [ 486.473] (--) Logitech USB Optical Mouse: Found relative axes
    [ 486.473] (--) Logitech USB Optical Mouse: Found x and y relative axes
    [ 486.473] (II) Logitech USB Optical Mouse: Configuring as mouse
    [ 486.473] (II) Logitech USB Optical Mouse: Adding scrollwheel support
    [ 486.473] (**) Logitech USB Optical Mouse: YAxisMapping: buttons 4 and 5
    [ 486.473] (**) Logitech USB Optical Mouse: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
    [ 486.473] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.1/usb9/9-2/9-2:1.0/input/input5/event5"
    [ 486.473] (II) XINPUT: Adding extended input device "Logitech USB Optical Mouse" (type: MOUSE)
    [ 486.473] (II) Logitech USB Optical Mouse: initialized for relative axes.
    [ 486.473] (**) Logitech USB Optical Mouse: (accel) keeping acceleration scheme 1
    [ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration profile 0
    [ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration factor: 2.000
    [ 486.473] (**) Logitech USB Optical Mouse: (accel) acceleration threshold: 4
    [ 486.473] (II) config/udev: Adding input device Logitech USB Optical Mouse (/dev/input/mouse0)
    [ 486.473] (II) No input driver/identifier specified (ignoring)
    [ 525.530] (WW) NVIDIA(0): The NVIDIA X driver has encountered too many errors. Falling
    [ 525.530] (WW) NVIDIA(0): back to write-back cached memory.
    dmesg.txt
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Linux version 2.6.38-ARCH (tobias@T-POWA-LX) (gcc version 4.6.0 20110415 (prerelease) (GCC) ) #1 SMP PREEMPT Fri Apr 22 17:48:36 UTC 2011
    [ 0.000000] BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009ec00 (usable)
    [ 0.000000] BIOS-e820: 000000000009ec00 - 00000000000a0000 (reserved)
    [ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
    [ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff90000 (usable)
    [ 0.000000] BIOS-e820: 000000007ff90000 - 000000007ff9e000 (ACPI data)
    [ 0.000000] BIOS-e820: 000000007ff9e000 - 000000007ffe0000 (ACPI NVS)
    [ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
    [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
    [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
    [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
    [ 0.000000] DMI 2.4 present.
    [ 0.000000] DMI: System manufacturer System Product Name/P5B-Deluxe, BIOS 1238 09/30/2008
    [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
    [ 0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
    [ 0.000000] last_pfn = 0x7ff90 max_arch_pfn = 0x100000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-DFFFF uncachable
    [ 0.000000] E0000-EFFFF write-through
    [ 0.000000] F0000-FFFFF write-protect
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F80000000 write-back
    [ 0.000000] 1 disabled
    [ 0.000000] 2 disabled
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] found SMP MP-table at [c00ff780] ff780
    [ 0.000000] initial memory mapped : 0 - 01800000
    [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
    [ 0.000000] 0000000000 - 0000400000 page 4k
    [ 0.000000] 0000400000 - 0037400000 page 2M
    [ 0.000000] 0037400000 - 00377fe000 page 4k
    [ 0.000000] kernel direct mapping tables up to 377fe000 @ 17fb000-1800000
    [ 0.000000] RAMDISK: 7fdd0000 - 7ff80000
    [ 0.000000] Allocated new RAMDISK: 3764e000 - 377fd262
    [ 0.000000] Move RAMDISK from 000000007fdd0000 - 000000007ff7f261 to 3764e000 - 377fd261
    [ 0.000000] ACPI: RSDP 000fae70 00024 (v02 ACPIAM)
    [ 0.000000] ACPI: XSDT 7ff90100 0004C (v01 MSTEST OEMXSDT 09000830 MSFT 00000097)
    [ 0.000000] ACPI: FACP 7ff90290 000F4 (v03 MSTEST OEMFACP 09000830 MSFT 00000097)
    [ 0.000000] ACPI: DSDT 7ff905c0 0918E (v01 A0483 A0483035 00000035 INTL 20060113)
    [ 0.000000] ACPI: FACS 7ff9e000 00040
    [ 0.000000] ACPI: APIC 7ff90390 0006C (v01 MSTEST OEMAPIC 09000830 MSFT 00000097)
    [ 0.000000] ACPI: MCFG 7ff90400 0003C (v01 MSTEST OEMMCFG 09000830 MSFT 00000097)
    [ 0.000000] ACPI: OEMB 7ff9e040 0007B (v01 MSTEST AMI_OEM 09000830 MSFT 00000097)
    [ 0.000000] ACPI: HPET 7ff99750 00038 (v01 MSTEST OEMHPET 09000830 MSFT 00000097)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] 1159MB HIGHMEM available.
    [ 0.000000] 887MB LOWMEM available.
    [ 0.000000] mapped low ram: 0 - 377fe000
    [ 0.000000] low ram: 0 - 377fe000
    [ 0.000000] Zone PFN ranges:
    [ 0.000000] DMA 0x00000010 -> 0x00001000
    [ 0.000000] Normal 0x00001000 -> 0x000377fe
    [ 0.000000] HighMem 0x000377fe -> 0x0007ff90
    [ 0.000000] Movable zone start PFN for each node
    [ 0.000000] early_node_map[2] active PFN ranges
    [ 0.000000] 0: 0x00000010 -> 0x0000009e
    [ 0.000000] 0: 0x00000100 -> 0x0007ff90
    [ 0.000000] On node 0 totalpages: 524062
    [ 0.000000] free_area_init_node: node 0, pgdat c1450b00, node_mem_map f664d200
    [ 0.000000] DMA zone: 32 pages used for memmap
    [ 0.000000] DMA zone: 0 pages reserved
    [ 0.000000] DMA zone: 3950 pages, LIFO batch:0
    [ 0.000000] Normal zone: 1744 pages used for memmap
    [ 0.000000] Normal zone: 221486 pages, LIFO batch:31
    [ 0.000000] HighMem zone: 2320 pages used for memmap
    [ 0.000000] HighMem zone: 294530 pages, LIFO batch:31
    [ 0.000000] Using APIC driver default
    [ 0.000000] ACPI: PM-Timer IO Port: 0x808
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
    [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a202 base: 0xfed00000
    [ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
    [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
    [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e4000
    [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 0000000000100000
    [ 0.000000] Allocating PCI resources starting at 80000000 (gap: 80000000:7ee00000)
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 12 pages/cpu @f6000000 s27392 r0 d21760 u1048576
    [ 0.000000] pcpu-alloc: s27392 r0 d21760 u1048576 alloc=1*4194304
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 519966
    [ 0.000000] Kernel command line: root=/dev/sda3 ro
    [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
    [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
    [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
    [ 0.000000] Initializing CPU#0
    [ 0.000000] xsave/xrstor: enabled xstate_bv 0x3, cntxt size 0x240
    [ 0.000000] allocated 10483200 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Initializing HighMem for node 0 (000377fe:0007ff90)
    [ 0.000000] Memory: 2061020k/2096704k available (3182k kernel code, 35228k reserved, 1259k data, 424k init, 1187400k highmem)
    [ 0.000000] virtual kernel memory layout:
    [ 0.000000] fixmap : 0xfff16000 - 0xfffff000 ( 932 kB)
    [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
    [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
    [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
    [ 0.000000] .init : 0xc1457000 - 0xc14c1000 ( 424 kB)
    [ 0.000000] .data : 0xc131bacb - 0xc1456a00 (1259 kB)
    [ 0.000000] .text : 0xc1000000 - 0xc131bacb (3182 kB)
    [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
    [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptable hierarchical RCU implementation.
    [ 0.000000] RCU-based detection of stalled CPUs is disabled.
    [ 0.000000] Verbose stalled-CPUs detection is disabled.
    [ 0.000000] NR_IRQS:512
    [ 0.000000] CPU 0 irqstacks, hard=f500c000 soft=f500e000
    [ 0.000000] Extended CMOS year: 2000
    [ 0.000000] Console: colour VGA+ 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] hpet clockevent registered
    [ 0.000000] Fast TSC calibration using PIT
    [ 0.000000] Detected 3066.221 MHz processor.
    [ 0.003336] Calibrating delay loop (skipped), value calculated using timer frequency.. 6134.96 BogoMIPS (lpj=10220736)
    [ 0.003418] pid_max: default: 32768 minimum: 301
    [ 0.003486] Security Framework initialized
    [ 0.003528] AppArmor: AppArmor disabled by boot time parameter
    [ 0.006682] Mount-cache hash table entries: 512
    [ 0.006865] Initializing cgroup subsys ns
    [ 0.006906] ns_cgroup deprecated: consider using the 'clone_children' flag without the ns_cgroup.
    [ 0.006960] Initializing cgroup subsys cpuacct
    [ 0.007007] Initializing cgroup subsys memory
    [ 0.007052] Initializing cgroup subsys devices
    [ 0.007092] Initializing cgroup subsys freezer
    [ 0.007133] Initializing cgroup subsys net_cls
    [ 0.007172] Initializing cgroup subsys blkio
    [ 0.007238] CPU: Physical Processor ID: 0
    [ 0.007277] CPU: Processor Core ID: 0
    [ 0.007317] mce: CPU supports 6 MCE banks
    [ 0.007361] CPU0: Thermal monitoring enabled (TM2)
    [ 0.007402] using mwait in idle threads.
    [ 0.008216] ACPI: Core revision 20110112
    [ 0.013386] Enabling APIC mode: Flat. Using 1 I/O APICs
    [ 0.013726] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.046907] CPU0: Intel(R) Core(TM)2 Duo CPU E7600 @ 3.06GHz stepping 0a
    [ 0.049997] Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
    [ 0.049997] ... version: 2
    [ 0.049997] ... bit width: 40
    [ 0.049997] ... generic registers: 2
    [ 0.049997] ... value mask: 000000ffffffffff
    [ 0.049997] ... max period: 000000007fffffff
    [ 0.049997] ... fixed-purpose events: 3
    [ 0.049997] ... event mask: 0000000700000003
    [ 0.056745] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.070012] CPU 1 irqstacks, hard=f50d6000 soft=f50d8000
    [ 0.070017] Booting Node 0, Processors #1
    [ 0.006666] Initializing CPU#1
    [ 0.166676] NMI watchdog enabled, takes one hw-pmu counter.
    [ 0.169997] Brought up 2 CPUs
    [ 0.170040] Total of 2 processors activated (12270.81 BogoMIPS).
    [ 0.171248] devtmpfs: initialized
    [ 0.171248] NET: Registered protocol family 16
    [ 0.171248] ACPI: bus type pci registered
    [ 0.171248] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.171248] PCI: not using MMCONFIG
    [ 0.171248] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
    [ 0.171248] PCI: Using configuration type 1 for base access
    [ 0.171248] bio: create slab <bio-0> at 0
    [ 0.173388] ACPI: EC: Look up EC in DSDT
    [ 0.174194] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.179022] ACPI: SSDT 7ff9e0c0 00208 (v01 AMI CPU1PM 00000001 INTL 20060113)
    [ 0.179316] ACPI: Dynamic OEM Table Load:
    [ 0.179408] ACPI: SSDT (null) 00208 (v01 AMI CPU1PM 00000001 INTL 20060113)
    [ 0.179643] ACPI: SSDT 7ff9e2d0 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
    [ 0.179932] ACPI: Dynamic OEM Table Load:
    [ 0.180025] ACPI: SSDT (null) 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
    [ 0.180248] ACPI: Interpreter enabled
    [ 0.180292] ACPI: (supports S0 S3 S4 S5)
    [ 0.180445] ACPI: Using IOAPIC for interrupt routing
    [ 0.180500] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.180904] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.180958] PCI: Using MMCONFIG for extended config space
    [ 0.185933] ACPI: No dock devices found.
    [ 0.185973] HEST: Table not found.
    [ 0.186014] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.186114] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.186260] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
    [ 0.186304] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
    [ 0.186346] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
    [ 0.186398] pci_root PNP0A08:00: host bridge window [mem 0x000d0000-0x000dffff]
    [ 0.186450] pci_root PNP0A08:00: host bridge window [mem 0x80000000-0xffffffff]
    [ 0.186509] pci 0000:00:00.0: [8086:29a0] type 0 class 0x000600
    [ 0.186539] pci 0000:00:01.0: [8086:29a1] type 1 class 0x000604
    [ 0.186562] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
    [ 0.186564] pci 0000:00:01.0: PME# disabled
    [ 0.186592] pci 0000:00:1a.0: [8086:2834] type 0 class 0x000c03
    [ 0.186625] pci 0000:00:1a.0: reg 20: [io 0xa880-0xa89f]
    [ 0.186660] pci 0000:00:1a.1: [8086:2835] type 0 class 0x000c03
    [ 0.186692] pci 0000:00:1a.1: reg 20: [io 0xac00-0xac1f]
    [ 0.186724] pci 0000:00:1a.7: [8086:283a] type 0 class 0x000c03
    [ 0.186740] pci 0000:00:1a.7: reg 10: [mem 0xf9fffc00-0xf9ffffff]
    [ 0.186797] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
    [ 0.186801] pci 0000:00:1a.7: PME# disabled
    [ 0.186817] pci 0000:00:1b.0: [8086:284b] type 0 class 0x000403
    [ 0.186829] pci 0000:00:1b.0: reg 10: [mem 0xf9ff8000-0xf9ffbfff 64bit]
    [ 0.186873] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.186876] pci 0000:00:1b.0: PME# disabled
    [ 0.186891] pci 0000:00:1c.0: [8086:283f] type 1 class 0x000604
    [ 0.186935] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.186938] pci 0000:00:1c.0: PME# disabled
    [ 0.186956] pci 0000:00:1c.4: [8086:2847] type 1 class 0x000604
    [ 0.187000] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
    [ 0.187003] pci 0000:00:1c.4: PME# disabled
    [ 0.187019] pci 0000:00:1c.5: [8086:2849] type 1 class 0x000604
    [ 0.187063] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
    [ 0.187066] pci 0000:00:1c.5: PME# disabled
    [ 0.187082] pci 0000:00:1d.0: [8086:2830] type 0 class 0x000c03
    [ 0.187114] pci 0000:00:1d.0: reg 20: [io 0xa400-0xa41f]
    [ 0.187137] pci 0000:00:1d.1: [8086:2831] type 0 class 0x000c03
    [ 0.187170] pci 0000:00:1d.1: reg 20: [io 0xa480-0xa49f]
    [ 0.187193] pci 0000:00:1d.2: [8086:2832] type 0 class 0x000c03
    [ 0.187226] pci 0000:00:1d.2: reg 20: [io 0xa800-0xa81f]
    [ 0.187256] pci 0000:00:1d.7: [8086:2836] type 0 class 0x000c03
    [ 0.187272] pci 0000:00:1d.7: reg 10: [mem 0xf9fff800-0xf9fffbff]
    [ 0.187329] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
    [ 0.187333] pci 0000:00:1d.7: PME# disabled
    [ 0.187346] pci 0000:00:1e.0: [8086:244e] type 1 class 0x000604
    [ 0.187393] pci 0000:00:1f.0: [8086:2810] type 0 class 0x000601
    [ 0.187462] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0294 (mask 0003)
    [ 0.188664] pci 0000:00:1f.2: [8086:2821] type 0 class 0x000106
    [ 0.188677] pci 0000:00:1f.2: reg 10: [io 0xa080-0xa087]
    [ 0.188684] pci 0000:00:1f.2: reg 14: [io 0xa000-0xa003]
    [ 0.188690] pci 0000:00:1f.2: reg 18: [io 0x9c00-0x9c07]
    [ 0.188696] pci 0000:00:1f.2: reg 1c: [io 0x9880-0x9883]
    [ 0.188703] pci 0000:00:1f.2: reg 20: [io 0x9800-0x981f]
    [ 0.188709] pci 0000:00:1f.2: reg 24: [mem 0xf9fff000-0xf9fff7ff]
    [ 0.188733] pci 0000:00:1f.2: PME# supported from D3hot
    [ 0.188736] pci 0000:00:1f.2: PME# disabled
    [ 0.188747] pci 0000:00:1f.3: [8086:283e] type 0 class 0x000c05
    [ 0.188756] pci 0000:00:1f.3: reg 10: [mem 0x00000000-0x000000ff]
    [ 0.188778] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
    [ 0.188824] pci 0000:01:00.0: [10de:0a65] type 0 class 0x000300
    [ 0.188832] pci 0000:01:00.0: reg 10: [mem 0xfa000000-0xfaffffff]
    [ 0.188841] pci 0000:01:00.0: reg 14: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.188849] pci 0000:01:00.0: reg 1c: [mem 0xce000000-0xcfffffff 64bit pref]
    [ 0.188856] pci 0000:01:00.0: reg 24: [io 0xbc00-0xbc7f]
    [ 0.188862] pci 0000:01:00.0: reg 30: [mem 0xfbc00000-0xfbc7ffff pref]
    [ 0.188895] pci 0000:01:00.1: [10de:0be3] type 0 class 0x000403
    [ 0.188903] pci 0000:01:00.1: reg 10: [mem 0xfbcfc000-0xfbcfffff]
    [ 0.188969] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.189011] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff]
    [ 0.189014] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfbcfffff]
    [ 0.189017] pci 0000:00:01.0: bridge window [mem 0xce000000-0xdfffffff 64bit pref]
    [ 0.189048] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
    [ 0.189091] pci 0000:00:1c.0: bridge window [io 0xf000-0x0000] (disabled)
    [ 0.189094] pci 0000:00:1c.0: bridge window [mem 0xfff00000-0x000fffff] (disabled)
    [ 0.189098] pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.189144] pci 0000:03:00.0: [197b:2363] type 0 class 0x000101
    [ 0.189223] pci 0000:03:00.0: reg 24: [mem 0xfbefe000-0xfbefffff]
    [ 0.189236] pci 0000:03:00.0: reg 30: [mem 0xfbee0000-0xfbeeffff pref]
    [ 0.189263] pci 0000:03:00.0: PME# supported from D3hot
    [ 0.189268] pci 0000:03:00.0: PME# disabled
    [ 0.189293] pci 0000:03:00.1: [197b:2363] type 0 class 0x000101
    [ 0.189315] pci 0000:03:00.1: reg 10: [io 0xdc00-0xdc07]
    [ 0.189327] pci 0000:03:00.1: reg 14: [io 0xd880-0xd883]
    [ 0.189339] pci 0000:03:00.1: reg 18: [io 0xd800-0xd807]
    [ 0.189351] pci 0000:03:00.1: reg 1c: [io 0xd480-0xd483]
    [ 0.189363] pci 0000:03:00.1: reg 20: [io 0xd400-0xd40f]
    [ 0.189426] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.189491] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
    [ 0.189533] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
    [ 0.189536] pci 0000:00:1c.4: bridge window [mem 0xfbe00000-0xfbefffff]
    [ 0.189540] pci 0000:00:1c.4: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.189589] pci 0000:02:00.0: [11ab:4364] type 0 class 0x000200
    [ 0.189609] pci 0000:02:00.0: reg 10: [mem 0xfbdfc000-0xfbdfffff 64bit]
    [ 0.189620] pci 0000:02:00.0: reg 18: [io 0xc800-0xc8ff]
    [ 0.189658] pci 0000:02:00.0: reg 30: [mem 0xfbdc0000-0xfbddffff pref]
    [ 0.189693] pci 0000:02:00.0: supports D1 D2
    [ 0.189694] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.189698] pci 0000:02:00.0: PME# disabled
    [ 0.193338] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
    [ 0.193385] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
    [ 0.193390] pci 0000:00:1c.5: bridge window [mem 0xfbd00000-0xfbdfffff]
    [ 0.193397] pci 0000:00:1c.5: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.193434] pci 0000:05:02.0: [1033:0035] type 0 class 0x000c03
    [ 0.193452] pci 0000:05:02.0: reg 10: [mem 0xfbffd000-0xfbffdfff]
    [ 0.193514] pci 0000:05:02.0: supports D1 D2
    [ 0.193516] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot
    [ 0.193519] pci 0000:05:02.0: PME# disabled
    [ 0.193533] pci 0000:05:02.1: [1033:0035] type 0 class 0x000c03
    [ 0.193546] pci 0000:05:02.1: reg 10: [mem 0xfbffe000-0xfbffefff]
    [ 0.193601] pci 0000:05:02.1: supports D1 D2
    [ 0.193602] pci 0000:05:02.1: PME# supported from D0 D1 D2 D3hot
    [ 0.193605] pci 0000:05:02.1: PME# disabled
    [ 0.193619] pci 0000:05:02.2: [1033:00e0] type 0 class 0x000c03
    [ 0.193633] pci 0000:05:02.2: reg 10: [mem 0xfbfffc00-0xfbfffcff]
    [ 0.193687] pci 0000:05:02.2: supports D1 D2
    [ 0.193689] pci 0000:05:02.2: PME# supported from D0 D1 D2 D3hot
    [ 0.193692] pci 0000:05:02.2: PME# disabled
    [ 0.193711] pci 0000:05:03.0: [104c:8023] type 0 class 0x000c00
    [ 0.193726] pci 0000:05:03.0: reg 10: [mem 0xfbfff000-0xfbfff7ff]
    [ 0.193735] pci 0000:05:03.0: reg 14: [mem 0xfbff8000-0xfbffbfff]
    [ 0.193786] pci 0000:05:03.0: supports D1 D2
    [ 0.193787] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot
    [ 0.193791] pci 0000:05:03.0: PME# disabled
    [ 0.193806] pci 0000:05:04.0: [11ab:4320] type 0 class 0x000200
    [ 0.193823] pci 0000:05:04.0: reg 10: [mem 0xfbff4000-0xfbff7fff]
    [ 0.193831] pci 0000:05:04.0: reg 14: [io 0xe800-0xe8ff]
    [ 0.193867] pci 0000:05:04.0: reg 30: [mem 0xfbfc0000-0xfbfdffff pref]
    [ 0.193886] pci 0000:05:04.0: supports D1 D2
    [ 0.193888] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.193891] pci 0000:05:04.0: PME# disabled
    [ 0.193926] pci 0000:00:1e.0: PCI bridge to [bus 05-05] (subtractive decode)
    [ 0.193971] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
    [ 0.193974] pci 0000:00:1e.0: bridge window [mem 0xfbf00000-0xfbffffff]
    [ 0.193978] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled)
    [ 0.193980] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.193982] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.193983] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.193985] pci 0000:00:1e.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
    [ 0.193987] pci 0000:00:1e.0: bridge window [mem 0x80000000-0xffffffff] (subtractive decode)
    [ 0.194003] pci_bus 0000:00: on NUMA node 0
    [ 0.194005] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
    [ 0.194127] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
    [ 0.194156] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
    [ 0.194243] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
    [ 0.194277] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
    [ 0.194313] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
    [ 0.194355] pci0000:00: Requesting ACPI _OSC control (0x1d)
    [ 0.199969] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    [ 0.200342] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
    [ 0.200724] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
    [ 0.201105] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 *15)
    [ 0.201486] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 *11 12 14 15)
    [ 0.201868] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 *14 15)
    [ 0.202249] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 7 10 11 12 14 15)
    [ 0.202634] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 10 11 12 14 15)
    [ 0.203051] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.203107] vgaarb: loaded
    [ 0.203206] PCI: Using ACPI for IRQ routing
    [ 0.203247] PCI: pci_cache_line_size set to 64 bytes
    [ 0.203358] reserve RAM buffer: 000000000009ec00 - 000000000009ffff
    [ 0.203360] reserve RAM buffer: 000000007ff90000 - 000000007fffffff
    [ 0.203439] NetLabel: Initializing
    [ 0.203478] NetLabel: domain hash size = 128
    [ 0.203518] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.203565] NetLabel: unlabeled traffic allowed by default
    [ 0.203608] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
    [ 0.203653] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
    [ 0.203797] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
    [ 0.210012] Switching to clocksource hpet
    [ 0.211034] pnp: PnP ACPI init
    [ 0.211084] ACPI: bus type pnp registered
    [ 0.211173] pnp 00:00: [bus 00-ff]
    [ 0.211175] pnp 00:00: [io 0x0cf8-0x0cff]
    [ 0.211177] pnp 00:00: [io 0x0000-0x0cf7 window]
    [ 0.211179] pnp 00:00: [io 0x0d00-0xffff window]
    [ 0.211180] pnp 00:00: [mem 0x000a0000-0x000bffff window]
    [ 0.211182] pnp 00:00: [mem 0x000d0000-0x000dffff window]
    [ 0.211184] pnp 00:00: [mem 0x80000000-0xffffffff window]
    [ 0.211222] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
    [ 0.211229] pnp 00:01: [mem 0xfed14000-0xfed19fff]
    [ 0.211267] system 00:01: [mem 0xfed14000-0xfed19fff] has been reserved
    [ 0.211311] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.211335] pnp 00:02: [dma 4]
    [ 0.211337] pnp 00:02: [io 0x0000-0x000f]
    [ 0.211338] pnp 00:02: [io 0x0081-0x0083]
    [ 0.211339] pnp 00:02: [io 0x0087]
    [ 0.211341] pnp 00:02: [io 0x0089-0x008b]
    [ 0.211342] pnp 00:02: [io 0x008f]
    [ 0.211343] pnp 00:02: [io 0x00c0-0x00df]
    [ 0.211367] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.211374] pnp 00:03: [io 0x0070-0x0071]
    [ 0.211380] pnp 00:03: [irq 8]
    [ 0.211403] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.211412] pnp 00:04: [io 0x0061]
    [ 0.211435] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.211441] pnp 00:05: [io 0x00f0-0x00ff]
    [ 0.211444] pnp 00:05: [irq 13]
    [ 0.211469] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.211669] pnp 00:06: [irq 4]
    [ 0.211671] pnp 00:06: [dma 0 disabled]
    [ 0.211672] pnp 00:06: [io 0x03f8-0x03ff]
    [ 0.211721] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.211835] pnp 00:07: [io 0x0000-0xffffffff disabled]
    [ 0.211837] pnp 00:07: [io 0x0000-0xffffffff disabled]
    [ 0.211838] pnp 00:07: [io 0x0290-0x0297]
    [ 0.211879] system 00:07: [io 0x0290-0x0297] has been reserved
    [ 0.211922] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.211997] pnp 00:08: [io 0x0010-0x001f]
    [ 0.211999] pnp 00:08: [io 0x0022-0x003f]
    [ 0.212000] pnp 00:08: [io 0x0044-0x005f]
    [ 0.212002] pnp 00:08: [io 0x0062-0x0063]
    [ 0.212003] pnp 00:08: [io 0x0065-0x006f]
    [ 0.212004] pnp 00:08: [io 0x0072-0x007f]
    [ 0.212006] pnp 00:08: [io 0x0080]
    [ 0.212007] pnp 00:08: [io 0x0084-0x0086]
    [ 0.212008] pnp 00:08: [io 0x0088]
    [ 0.212010] pnp 00:08: [io 0x008c-0x008e]
    [ 0.212011] pnp 00:08: [io 0x0090-0x009f]
    [ 0.212012] pnp 00:08: [io 0x00a2-0x00bf]
    [ 0.212014] pnp 00:08: [io 0x00e0-0x00ef]
    [ 0.212015] pnp 00:08: [io 0x04d0-0x04d1]
    [ 0.212016] pnp 00:08: [io 0x0800-0x087f]
    [ 0.212018] pnp 00:08: [io 0x0400-0x03ff disabled]
    [ 0.212019] pnp 00:08: [io 0x0480-0x04bf]
    [ 0.212021] pnp 00:08: [mem 0xffafe000-0xffb0cbff]
    [ 0.212022] pnp 00:08: [mem 0xffb00000-0xffbfffff]
    [ 0.212024] pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
    [ 0.212025] pnp 00:08: [mem 0xfed20000-0xfed8ffff]
    [ 0.212026] pnp 00:08: [mem 0xfff00000-0xfffffffe]
    [ 0.212028] pnp 00:08: [mem 0xfebfe000-0xfebfec00]
    [ 0.212089] system 00:08: [io 0x04d0-0x04d1] has been reserved
    [ 0.212132] system 00:08: [io 0x0800-0x087f] has been reserved
    [ 0.212174] system 00:08: [io 0x0480-0x04bf] has been reserved
    [ 0.212216] system 00:08: [mem 0xffafe000-0xffb0cbff] could not be reserved
    [ 0.212259] system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved
    [ 0.212302] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
    [ 0.212345] system 00:08: [mem 0xfed20000-0xfed8ffff] has been reserved
    [ 0.212388] system 00:08: [mem 0xfff00000-0xfffffffe] has been reserved
    [ 0.212430] system 00:08: [mem 0xfebfe000-0xfebfec00] has been reserved
    [ 0.212473] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.212521] pnp 00:09: [mem 0xfed00000-0xfed003ff]
    [ 0.212547] pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.212580] pnp 00:0a: [mem 0xfec00000-0xfec00fff]
    [ 0.212581] pnp 00:0a: [mem 0xfee00000-0xfee00fff]
    [ 0.212625] system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.212668] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
    [ 0.212712] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.212761] pnp 00:0b: [mem 0xe0000000-0xefffffff]
    [ 0.212801] system 00:0b: [mem 0xe0000000-0xefffffff] has been reserved
    [ 0.212844] system 00:0b: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.212967] pnp 00:0c: [mem 0x00000000-0x0009ffff]
    [ 0.212969] pnp 00:0c: [mem 0x000c0000-0x000cffff]
    [ 0.212971] pnp 00:0c: [mem 0x000e0000-0x000fffff]
    [ 0.212972] pnp 00:0c: [mem 0x00100000-0x7fffffff]
    [ 0.212974] pnp 00:0c: [mem 0x00000000-0xffffffff disabled]
    [ 0.213025] system 00:0c: [mem 0x00000000-0x0009ffff] could not be reserved
    [ 0.213068] system 00:0c: [mem 0x000c0000-0x000cffff] could not be reserved
    [ 0.213111] system 00:0c: [mem 0x000e0000-0x000fffff] could not be reserved
    [ 0.213154] system 00:0c: [mem 0x00100000-0x7fffffff] could not be reserved
    [ 0.213198] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.213198] Switched to NOHz mode on CPU #0
    [ 0.213237] Switched to NOHz mode on CPU #1
    [ 0.213286] pnp: PnP ACPI: found 13 devices
    [ 0.213326] ACPI: ACPI bus type pnp unregistered
    [ 0.249481] pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x803fffff]
    [ 0.249526] pci 0000:00:1c.4: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.249579] pci 0000:00:1c.5: BAR 15: assigned [mem 0x80600000-0x807fffff 64bit pref]
    [ 0.249632] pci 0000:00:1c.0: BAR 13: assigned [io 0x1000-0x1fff]
    [ 0.249675] pci 0000:00:1f.3: BAR 0: assigned [mem 0x80800000-0x808000ff]
    [ 0.249720] pci 0000:00:1f.3: BAR 0: set to [mem 0x80800000-0x808000ff] (PCI address [0x80800000-0x808000ff])
    [ 0.249775] pci 0000:00:01.0: PCI bridge to [bus 01-01]
    [ 0.249816] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff]
    [ 0.249859] pci 0000:00:01.0: bridge window [mem 0xfa000000-0xfbcfffff]
    [ 0.249902] pci 0000:00:01.0: bridge window [mem 0xce000000-0xdfffffff 64bit pref]
    [ 0.249956] pci 0000:00:1c.0: PCI bridge to [bus 04-04]
    [ 0.250011] pci 0000:00:1c.0: bridge window [io 0x1000-0x1fff]
    [ 0.250055] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x803fffff]
    [ 0.250099] pci 0000:00:1c.0: bridge window [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.250154] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
    [ 0.250195] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
    [ 0.250239] pci 0000:00:1c.4: bridge window [mem 0xfbe00000-0xfbefffff]
    [ 0.250283] pci 0000:00:1c.4: bridge window [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.250338] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
    [ 0.250380] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
    [ 0.250424] pci 0000:00:1c.5: bridge window [mem 0xfbd00000-0xfbdfffff]
    [ 0.250468] pci 0000:00:1c.5: bridge window [mem 0x80600000-0x807fffff 64bit pref]
    [ 0.250523] pci 0000:00:1e.0: PCI bridge to [bus 05-05]
    [ 0.250565] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
    [ 0.250609] pci 0000:00:1e.0: bridge window [mem 0xfbf00000-0xfbffffff]
    [ 0.250653] pci 0000:00:1e.0: bridge window [mem pref disabled]
    [ 0.250702] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.250746] pci 0000:00:01.0: setting latency timer to 64
    [ 0.250750] pci 0000:00:1c.0: enabling device (0106 -> 0107)
    [ 0.250792] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.250836] pci 0000:00:1c.0: setting latency timer to 64
    [ 0.250840] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
    [ 0.250884] pci 0000:00:1c.4: setting latency timer to 64
    [ 0.250890] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 0.250933] pci 0000:00:1c.5: setting latency timer to 64
    [ 0.250938] pci 0000:00:1e.0: setting latency timer to 64
    [ 0.250941] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.250943] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.250944] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.250946] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.250948] pci_bus 0000:00: resource 8 [mem 0x80000000-0xffffffff]
    [ 0.250949] pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
    [ 0.250951] pci_bus 0000:01: resource 1 [mem 0xfa000000-0xfbcfffff]
    [ 0.250953] pci_bus 0000:01: resource 2 [mem 0xce000000-0xdfffffff 64bit pref]
    [ 0.250955] pci_bus 0000:04: resource 0 [io 0x1000-0x1fff]
    [ 0.250956] pci_bus 0000:04: resource 1 [mem 0x80000000-0x803fffff]
    [ 0.250958] pci_bus 0000:04: resource 2 [mem 0xf8f00000-0xf8ffffff 64bit pref]
    [ 0.250960] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
    [ 0.250961] pci_bus 0000:03: resource 1 [mem 0xfbe00000-0xfbefffff]
    [ 0.250963] pci_bus 0000:03: resource 2 [mem 0x80400000-0x805fffff 64bit pref]
    [ 0.250965] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
    [ 0.250966] pci_bus 0000:02: resource 1 [mem 0xfbd00000-0xfbdfffff]
    [ 0.250968] pci_bus 0000:02: resource 2 [mem 0x80600000-0x807fffff 64bit pref]
    [ 0.250970] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
    [ 0.250972] pci_bus 0000:05: resource 1 [mem 0xfbf00000-0xfbffffff]
    [ 0.250973] pci_bus 0000:05: resource 4 [io 0x0000-0x0cf7]
    [ 0.250975] pci_bus 0000:05: resource 5 [io 0x0d00-0xffff]
    [ 0.250977] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.250978] pci_bus 0000:05: resource 7 [mem 0x000d0000-0x000dffff]
    [ 0.250980] pci_bus 0000:05: resource 8 [mem 0x80000000-0xffffffff]
    [ 0.251002] NET: Registered protocol family 2
    [ 0.251085] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
    [ 0.251263] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
    [ 0.251592] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
    [ 0.251779] TCP: Hash tables configured (established 131072 bind 65536)
    [ 0.251822] TCP reno registered
    [ 0.251861] UDP hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.251907] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
    [ 0.252025] NET: Registered protocol family 1
    [ 0.295104] pci 0000:01:00.0: Boot video device
    [ 0.295141] PCI: CLS 32 bytes, default 64
    [ 0.295174] Unpacking initramfs...
    [ 0.317387] Freeing initrd memory: 1728k freed
    [ 0.318002] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
    [ 0.318046] apm: disabled - APM is not SMP safe.
    [ 0.318193] audit: initializing netlink socket (disabled)
    [ 0.318243] type=2000 audit(1303935493.316:1): initialized
    [ 0.318520] highmem bounce pool size: 64 pages
    [ 0.318562] HugeTLB registered 4 MB page size, pre-allocated 0 pages
    [ 0.320047] VFS: Disk quotas dquot_6.5.2
    [ 0.320145] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
    [ 0.320261] msgmni has been set to 1709
    [ 0.320435] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
    [ 0.320488] io scheduler noop registered
    [ 0.320527] io scheduler deadline registered
    [ 0.320574] io scheduler cfq registered (default)
    [ 0.320710] pcieport 0000:00:01.0: setting latency timer to 64
    [ 0.320734] pcieport 0000:00:01.0: irq 40 for MSI/MSI-X
    [ 0.320771] pcieport 0000:00:1c.0: setting latency timer to 64
    [ 0.320798] pcieport 0000:00:1c.0: irq 41 for MSI/MSI-X
    [ 0.320848] pcieport 0000:00:1c.4: setting latency timer to 64
    [ 0.320875] pcieport 0000:00:1c.4: irq 42 for MSI/MSI-X
    [ 0.320923] pcieport 0000:00:1c.5: setting latency timer to 64
    [ 0.320950] pcieport 0000:00:1c.5: irq 43 for MSI/MSI-X
    [ 0.321092] intel_idle: MWAIT substates: 0x22220
    [ 0.321094] intel_idle: does not run on family 6 model 23
    [ 0.321105] ERST: Table is not found!
    [ 0.321155] isapnp: Scanning for PnP cards...
    [ 0.676796] isapnp: No Plug & Play device found
    [ 0.676877] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.697390] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.920667] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
    [ 0.973728] i8042: PNP: No PS/2 controller found. Probing ports directly.
    [ 0.976563] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.976631] serio: i8042 AUX port at 0x60,0x64 irq 12
    [ 0.976752] mousedev: PS/2 mouse device common for all mice
    [ 0.976847] rtc_cmos 00:03: RTC can wake from S4
    [ 1.000070] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 1.000137] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
    [ 1.000200] cpuidle: using governor ladder
    [ 1.000240] cpuidle: using governor menu
    [ 1.000436] TCP cubic registered
    [ 1.000476] NET: Registered protocol family 17
    [ 1.000521] Registering the dns_resolver key type
    [ 1.000569] Using IPI No-Shortcut mode
    [ 1.000679] PM: Hibernation image not present or could not be loaded.
    [ 1.000682] registered taskstats version 1
    [ 1.001054] rtc_cmos 00:03: setting system clock to 2011-04-27 20:18:14 UTC (1303935494)
    [ 1.001128] Initalizing network drop monitor service
    [ 1.001211] Freeing unused kernel memory: 424k freed
    [ 1.005982] <30>udev[38]: starting version 167
    [ 1.107427] SCSI subsystem initialized
    [ 1.127245] libata version 3.00 loaded.
    [ 1.131006] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
    [ 1.131057] pata_jmicron 0000:03:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
    [ 1.131134] pata_jmicron 0000:03:00.1: setting latency timer to 64
    [ 1.131436] scsi0 : pata_jmicron
    [ 1.131554] scsi1 : pata_jmicron
    [ 1.132024] ata1: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
    [ 1.132068] ata2: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
    [ 1.142526] ahci 0000:00:1f.2: version 3.0
    [ 1.142536] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
    [ 1.142608] ahci 0000:00:1f.2: irq 44 for MSI/MSI-X
    [ 1.142644] ahci: SSS flag set, parallel bus scan disabled
    [ 1.142711] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
    [ 1.142765] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ccc ems sxs
    [ 1.142819] ahci 0000:00:1f.2: setting latency timer to 64
    [ 1.174032] scsi2 : ahci
    [ 1.174136] scsi3 : ahci
    [ 1.174235] scsi4 : ahci
    [ 1.174335] scsi5 : ahci
    [ 1.174434] scsi6 : ahci
    [ 1.174532] scsi7 : ahci
    [ 1.174699] ata3: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff100 irq 44
    [ 1.174752] ata4: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff180 irq 44
    [ 1.174804] ata5: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff200 irq 44
    [ 1.174856] ata6: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff280 irq 44
    [ 1.174908] ata7: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff300 irq 44
    [ 1.174960] ata8: SATA max UDMA/133 abar m2048@0xf9fff000 port 0xf9fff380 irq 44
    [ 1.175036] ahci 0000:03:00.0: PCI INT A -> GSI 16 (level,

    Hi jasonwryan,
    Your thread helps a lot. I saw a lot of posts but not this one.
    This workaround is fine for me to wait the fix.
    Thanks a lot
    Workaround :
    It seems the problem might be linked to transparent items like background.
    As explained in the above thread :
    According to the bug report the nVidia driver is freaking out and creating too many events, which causes an event buffer in Xorg to overflow.  It works OK with the older Xorg, though.
    So the temporary solution is to downgrade 3 packages.
    Install the tool to downgrade
    > yaourt -Sy downgrade
    Downgrade
    Note the item number can change
    > downgrade xf86-input-evdev
    Hit "s" key
    Choose 2 (xf86-input-evdev-2.6.0-2-i686.pkg.tar.xz)
    > downgrade xorg-server
    Hit "s" key
    Choose 1 (xorg-server-1.9.4.901-1-i686.pkg.tar.xz)
    > downgrade xorg-server-common
    Hit "s" key
    Choose 1 (xorg-server-common-1.9.4.901-1-i686.pkg.tar.xz)
    Be carefull : don't update these 3 packages when updating your system (pacman -Syu) since it is not fixed.
    Last edited by shefla (2011-04-27 22:36:37)

  • [GeForce 6] Big Problems with NX6600GT VTD128 AGP and Video Overlay

    Got trouble to Install the NX6600GT VTD128 AGP VGA-Adapter right.
    I already tried out with latest Drivers from MSI 71.22 and the ForceWare 66.93 NVidiadrivers, but no Overlay at all in my Grabbing Software.
    It's a DV-Storm of Canopus with Storm Edit installed. With my Ti4200 (also MSI VGA-Card) never had those Problems.
    In the Canopus Storm-Edit Software is an Preview-Window to check the grabbing Process. Now, with the new 6600GT Card it's a black screen.
    When I press any key, shortly I see a TV Picture. It's an Overlay Problem of the 6600GT.
    How do I have to install/configure the 6600GT VGA that Overlay is working fine.
    The System:
    Intel P4 HT 3,2 GHz
    ASUS P4P800 with AGP 8x
    DV-Storm in PCI Slot 2
    IDE Raid Promise Fasttrack 100
    1024 MB DDR400 Corsair CL2
    Latency Timer on 128 (doesn't work with PCI Latency Timer = 64 too)
    DirectX 9.0c, XP with SP2 and latest Patches, MSI-Driver Version 71.22 (or Reference Driver 66.93 NVidia)
    This Configuration is working fine (Overlay = OK) when re-install the GeForce4 Ti4200 of MSI
    >>>Problem solved<<<
    .....a wonderful Canopus Patch to "clean" the ForceWare Drivers like a big LIGHT in the Nvidia-DARKNESS gives hope and wellness to my PC 

    I found the solution while I cruised in the forum, I used Driver Cleaner to erase the driver file on my HD, and the installation worked perfectly... Sorry about my useless post     
    If it can help another one...

  • Problems with Nvidia 320.49 and Windows 8.1

    I am having problems with my HP Envy with windows 8.1... Nvidia driver keeps crashing.
    Took the unit to Best Buy and we determined it was with the 320.49 driver - we are
    able to reinstall it, and it will usually last for a few hours before it fails again.  When
    it fails, the resolution reverts to 1024 x XX... not the 1920 x 1260 when it works
    right... very frustrating, but I need to know if the card needs replacement, or if there
    is a fix from Nvidia... Contacted Nvidia and did not get anywhere with them.... can anyone
    help??

    Thank you for the additional information.
    If it is an HP OEM video card, this is the reason that it is not working with the retail nVidia driver.  HP has their motherboards and video cards made to their specs.  Only the drivers developed by them will work with their cards.
    Here are the drivers available for Win 8.1 on the Software & driver download page.
    Please click the "Thumbs up + button" if I have helped you and click "Accept as Solution" if your problem is solved.
    Signature:
    HP TouchPad - 1.2 GHz; 1 GB memory; 32 GB storage; WebOS/CyanogenMod 11(Kit Kat)
    HP 10 Plus; Android-Kit Kat; 1.0 GHz Allwinner A31 ARM Cortex A7 Quad Core Processor ; 2GB RAM Memory Long: 2 GB DDR3L SDRAM (1600MHz); 16GB disable eMMC 16GB v4.51
    HP Omen; i7-4710QH; 8 GB memory; 256 GB San Disk SSD; Win 8.1
    HP Photosmart 7520 AIO
    ++++++++++++++++++
    **Click the Thumbs Up+ to say 'Thanks' and the 'Accept as Solution' if I have solved your problem.**
    Intelligence is God given; Wisdom is the sum of our mistakes!
    I am not an HP employee.

  • Problems with Nvidia GeForce 210 and windows 8.1

    Hi all, I have Windows 8.1 Pro update 1 64bit installed, two weeks ago I started giving problems graphics card NVidia (even has me
    given several blue screen).
    I tried to update the drivers for the card but I got the same problem. It was working properly with generic
    drivers, and if I went to Computer Administrator me a yellow triangle appeared
    on my graphics card and the properties told me the following:
    Windows has stopped this device because it has reported problems.
    (Code 43 )
    My machine is as follows:
    Mainboard : Asus P5K SE
    Chipset: Intel P31/P35
    Processor : Intel Core 2 Quad Q6600 @ 2400MHz
    Physical Memory : 3072MB (3 x 1024 DDR2- SDRAM)
    Video Card : NVIDIA GeForce 8500 GT
    Hard Disk : Seagate ST3320620AS ATA Device (320GB )
    Monitor Type: LG Electronics L1919S
    I just formatted
     the computer from scratch, and
    I still had the same problem with the graphics card,
    so I imagined it would be a hardware problem
    and bought NVIDIA GeForce 210.
    In the end I
    upgraded to Windows 8.1 update 1 with
    the latest drivers for the GeForce 210,
    and after 6 days running everything correctly, a few days ago
    returned to give me problems,
    the screen sometimes freezes and will not
    let me do anything and after a while
    giving me a blue screen and reboots
    me, I suspect that the graphics drivers
    are giving me problems, and I had to
    disable the graphics card and work with
    generic drivers from Microsoft, and even then I
    was restarted once.
    I installed Driver Booster and all the drivers are updated.
    Could
     anyone analyze
    dump files dmp ? Download here 
    I got another dmp:
     C:\Windows\MEMORY.DMP  but it is too heavy.
    Thanks

    yes, I check the dump files
    this cause by graphic card, on which graphic card you reformat your PC and update
    .NET framework maybe cause this driver corrupted
    my suggestion is try using internal graphic card, just for testing
    Just in case you don't believe me, please check this dump file
    * Bugcheck Analysis *
    Use !analyze -v to get detailed debugging information.
    BugCheck 116, {ffffe000d84c4010, fffff800b540be2c, ffffffffc000009a, 4}
    Unable to load image \SystemRoot\system32\DRIVERS\nvlddmkm.sys, Win32 error 0n2
    *** WARNING: Unable to verify timestamp for nvlddmkm.sys
    *** ERROR: Module load completed but symbols could not be loaded for nvlddmkm.sys
    Probably caused by : nvlddmkm.sys ( nvlddmkm+9bbe2c )
    Followup: MachineOwner
    1: kd> !analyze -v
    * Bugcheck Analysis *
    VIDEO_TDR_FAILURE (116)
    Attempt to reset the display driver and recover from timeout failed.
    Arguments:
    Arg1: ffffe000d84c4010, Optional pointer to internal TDR recovery context (TDR_RECOVERY_CONTEXT).
    Arg2: fffff800b540be2c, The pointer into responsible device driver module (e.g. owner tag).
    Arg3: ffffffffc000009a, Optional error code (NTSTATUS) of the last failed operation.
    Arg4: 0000000000000004, Optional internal context dependent data.
    Debugging Details:
    FAULTING_IP:
    nvlddmkm+9bbe2c
    fffff800`b540be2c 803db68aeeff00 cmp byte ptr [nvlddmkm+0x8a48e9 (fffff800`b52f48e9)],0
    DEFAULT_BUCKET_ID: GRAPHICS_DRIVER_TDR_FAULT
    CUSTOMER_CRASH_COUNT: 1
    BUGCHECK_STR: 0x116
    PROCESS_NAME: System
    CURRENT_IRQL: 0
    ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre
    STACK_TEXT:
    ffffd000`8adadbb8 fffff800`b457bfac : 00000000`00000116 ffffe000`d84c4010 fffff800`b540be2c ffffffff`c000009a : nt!KeBugCheckEx
    ffffd000`8adadbc0 fffff800`b457008d : fffff800`b540be2c ffffe000`d760b7f0 ffffe000`d84c4010 00000000`00000001 : dxgkrnl!TdrBugcheckOnTimeout+0xec
    ffffd000`8adadc00 fffff800`b4570582 : ffffe000`d760f540 ffffd000`8adadc60 00000000`00000002 00000000`00000001 : dxgkrnl!ADAPTER_RENDER::Reset+0x1f5
    ffffd000`8adadc30 fffff800`b457b919 : ffffd000`8ada01b0 00000000`00000000 ffffe000`d5ff91a0 ffffe000`d742b000 : dxgkrnl!DXGADAPTER::Reset+0x416
    ffffd000`8adadca0 fffff800`b446cfde : fffff800`b4453c90 ffffe000`d742b000 fffff802`84c1c000 00000000`00000000 : dxgkrnl!TdrResetFromTimeout+0x15
    ffffd000`8adadcd0 fffff800`b4453d1d : ffffe000`d742b000 00000000`00000080 ffffe000`d50b4500 ffffe000`00000000 : dxgmms1!VidSchiRecoverFromTDR+0x1a
    ffffd000`8adadd00 fffff802`84ceb794 : fffff802`84f69a00 ffffe000`d50b4500 ffffd000`8adaddd0 fffff802`84d7337d : dxgmms1!VidSchiWorkerThread+0x8d
    ffffd000`8adadd40 fffff802`84d765c6 : fffff802`84f02180 ffffe000`d50b4500 fffff802`84f69a00 00000000`00000000 : nt!PspSystemThreadStartup+0x58
    ffffd000`8adadda0 00000000`00000000 : ffffd000`8adae000 ffffd000`8ada8000 00000000`00000000 00000000`00000000 : nt!KiStartSystemThread+0x16
    STACK_COMMAND: .bugcheck ; kb
    FOLLOWUP_IP:
    nvlddmkm+9bbe2c
    fffff800`b540be2c 803db68aeeff00 cmp byte ptr [nvlddmkm+0x8a48e9 (fffff800`b52f48e9)],0
    SYMBOL_NAME: nvlddmkm+9bbe2c
    FOLLOWUP_NAME: MachineOwner
    MODULE_NAME: nvlddmkm
    IMAGE_NAME: nvlddmkm.sys
    DEBUG_FLR_IMAGE_TIMESTAMP: 5315b408
    FAILURE_BUCKET_ID: 0x116_IMAGE_nvlddmkm.sys
    BUCKET_ID: 0x116_IMAGE_nvlddmkm.sys
    ANALYSIS_SOURCE: KM
    FAILURE_ID_HASH_STRING: km:0x116_image_nvlddmkm.sys
    FAILURE_ID_HASH: {c89bfe8c-ed39-f658-ef27-f2898997fdbd}
    Followup: MachineOwner
    1: kd> lmvm nvlddmkm
    start end module name
    fffff800`b4a50000 fffff800`b56a8000 nvlddmkm T (no symbols)
    Loaded symbol image file: nvlddmkm.sys
    Image path: \SystemRoot\system32\DRIVERS\nvlddmkm.sys
    Image name: nvlddmkm.sys
    Timestamp: Tue Mar 04 19:07:52 2014 (5315B408)
    CheckSum: 00C20523
    ImageSize: 00C58000
    Translations: 0000.04b0 0000.04e4 0409.04b0 0409.04e4

  • Varient configuration with Material type FERT and HAWA

    Hi,
    The requirement is for our Finished product and Trading goods, when we craete a sales order system should ask only about the entered material characerstics like color and size.No varient pricing.
    And latter in change mode also we can see for which color  of the material the sales order  was created.
    So here my material type are FERT ( item category TAN)and HAWA.(Item Category TAN)
    So my question is can i achive it through Varient Configuration.What i know we can create it with KMAT and Irem category group 002.
    Is it mandatory to have pricing in Varient configuration?Can we know in invoice and sales order for which color and size of the material the sales order was created?
    Regards
    Jyoti

    HI
    As per your two questions:
    1) Is it mandatory to have pricing in Varient configuration?
    No, its not mandatory to have pricing in variant config. You can create for colour and size only.
    2)Can we know in invoice and sales order for which color and size of the material the sales order was created?
    You can check the color and size in sales order but not in invoice.
    bye

  • Disk array configurations with oracle redo logs and flash recovery area.

    Dear Oracle users,
    We are planning to buy the new server for oracle database 10g standard edition. We put oracle database file, redo logs, and flash recovery area on each of disk array. My question is what is the best disk array configuration for redo logs and flash recovery area? RAID 10 or RAID 1? Is that possible we can duplicate Flash recovery area to the other location (such as net work drive) at the same time? Since we only have single disk array controller to connect to the disk arrays, I am try to avoid the single failure that will lose archive logs and daily backup.
    thanks,
    Belinda

    Thank you so much for the suggestion. Could you please let me know the answer for my question of FRA redundancy?
    “Is that possible we can duplicate Flash recovery area to the other location (such as net work drive) at the same time? Since we only have single disk array controller to connect to the disk arrays, I am try to avoid the single failure that will lose archive logs and daily backup.”

  • [SOLVED] Fixing slow scrolling in firefox with nvidia and 64 bit

    I'm experiencing very slow scrolling with firefox on sites like
    http://www.roadrunnerrecords.com/blabbermouth.net/
    http://www.vai.com/News/index.html
    I'm running 64 bit with KDEmod. Scrolling is fine when I remove flash completely but on Ubuntu 10.04 (64 bit) the abnove sites scroll fine on a different machine (with intel graphics). I read somewhere by modifying xorg with "AccelMethod" "EXA" to "XXA" scrolling becomes very smoth onm ATI and Intel. Here is my xorg.conf:
    Section "ServerLayout"
            Identifier     "X.org Configured"
            Screen      0  "Screen0" 0 0
            InputDevice    "Mouse0" "CorePointer"
            InputDevice    "Keyboard0" "CoreKeyboard"
    EndSection
    Section "Files"
            ModulePath   "/usr/lib/xorg/modules"
            FontPath     "/usr/share/fonts/misc"
            FontPath     "/usr/share/fonts/100dpi:unscaled"
            FontPath     "/usr/share/fonts/75dpi:unscaled"
            FontPath     "/usr/share/fonts/TTF"
            FontPath     "/usr/share/fonts/Type1"
    EndSection
    Section "Module"
            Load  "glx"
            Load  "record"
            Load  "dbe"
            Load  "extmod"
    EndSection
    Section "InputDevice"
            Identifier  "Keyboard0"
            Driver      "kbd"
    EndSection
    Section "InputDevice"
            Identifier  "Mouse0"
            Driver      "mouse"
            Option      "Protocol" "auto"
            Option      "Device" "/dev/input/mice"
            Option      "ZAxisMapping" "4 5 6 7"
    EndSection
    Section "Monitor"
            Identifier   "Monitor0"
            VendorName   "Monitor Vendor"
            ModelName    "Monitor Model"
            HorizSync    28.0 - 72.0
            VertRefresh  43.0 - 60.0
    EndSection
    Section "Device"
            Identifier  "Card0"
            Driver      "nvidia"
            VendorName  "nVidia Corporation"
            BoardName   "G92 [GeForce 9800 GT]"
            Option      "RenderAccel" "true"
            Option      "NoLogo" "true"
            Option      "AGPFastWrite" "true"
            Option      "EnablePageFlip" "true"
            BusID       "PCI:1:0:0"
    EndSection
    Section "Screen"
            Identifier "Screen0"
            Device     "Card0"
            Monitor    "Monitor0"
            SubSection "Display"
                    Viewport   0 0
                    Depth     1
            EndSubSection
            SubSection "Display"
                    Viewport   0 0
                    Depth     4
            EndSubSection
            SubSection "Display"
                    Viewport   0 0
                    Depth     8
            EndSubSection
            SubSection "Display"
                    Viewport   0 0
                    Depth     15
            EndSubSection
            SubSection "Display"
                    Viewport   0 0
                    Depth     16
            EndSubSection
            SubSection "Display"
                    Viewport   0 0
                    Depth     24
                    Modes    "1680x1050"
            EndSubSection
    EndSection
    Section "Extensions"
            Option "Composite" "Enable"
            Option "RENDER" "Enable"
    EndSection
    is there something I can change to improve scrolling in firefox? I've tried to turnoff desktop effects and scrolling is the same annd also running firefox from a fresh profile. Hence, i suspect my nvidia 9800GT card to be the culprit. If anyone has a working xorg.conf with nvidia, 64 bit and smooth scrolling on the above mentioned sites please SHARE! Many Thanks!
    Last edited by fettouhi (2012-02-22 17:42:10)

    karol wrote:
    > Tried it now and that worked. Running without a xorg.conf buty now I can't turn on desktop effects in KDE. How do I set that up?
    Sorry, I don't use KDE, but it may be related to how do you start KDE: from xinit or via KDM or sth.
    > How do I determine what driver xorg is using now that I'm running without it xorg.conf?
    It's running the same driver as before.
    > Using the binary nvidia blob driver.
    Did you uninstall it? Did you install the nouveau driver? 'pacman -Qqs xf86-video' will tell you what drivers you have installed.
    No, I don't have the nouveau driver installed. I have to check if I have the nv driver installed but I didn't uninstall the nvidia driver. I'm starting KDE via xinit.

  • SOLVED Blurry/Ghosting LCD with Nvidia-96xx

    Hi all,
    I've spent hours trying to figure this out...  I installed the Nvidia-96xx driver for my Geforce2 MX/MX 400 and everything seems ok in my xorg.conf.  XFCE comes up with the right resolution (1280x1024 Dell 1702fp), but everything is blurry.  When i use the Nvidia X Server Settings application, it looks like everything is running correctly - 1280x1024 @ 60hz.  But this doesn't seem right, because otherwise everything wouldn't look so blurry.  And I do mean everything - fonts, icons, etc.
    So I did a bunch of reading and decided to try xrandr.  Well, that seems like a fairly cool command, but it didn't really solve my problem.  However, it did confirm my suspicions that one of these programs is giving me the wrong information, since the only 1280x1024 resolution it gives me is at a 50* 51 refresh rate.  I tried changing the rate with:
    xrandr -r 60
    It wouldn't let me do it.  It says:
    "Rate not available for this size"
    I'm really kind of puzzled about this, I've tried three different ways of generating xorg.conf files (Xorg -configure, xorgconfig, nvidia-xconfig) and they all give me the right resolution, but the wrong refresh rate.  For some reason linux wants to run things at 50hz...
    I'd post more information up here, but I'm not sure what you would want to see.  I'm pretty sure it's not the xorg.conf...
    Hope you guys can help.
    Last edited by syan (2007-02-20 17:40:50)

    Thanks for the reply, berbae.
    I've been trying different things with the xorg.conf file, but nothing I do seems to help.  I tried adding in some of the things you had in yours, like the EDID option and now my xorg.conf looks like this:
    Section "ServerLayout"
    Identifier "X.org Configured"
    Screen 0 "Screen0" 0 0
    InputDevice "Mouse0" "CorePointer"
    InputDevice "Keyboard0" "CoreKeyboard"
    EndSection
    Section "Files"
    RgbPath "/usr/share/X11/rgb"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc"
    FontPath "/usr/share/fonts/75dpi"
    FontPath "/usr/share/fonts/100dpi"
    FontPath "/usr/share/fonts/TTF"
    FontPath "/usr/share/fonts/Type1"
    EndSection
    Section "Module"
    Load "xtrap"
    Load "dbe"
    Load "record"
    Load "extmod"
    Load "dri"
    Load "glx"
    Load "type1"
    Load "freetype"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/input/mice"
    Option "ZAxisMapping" "4 5 6 7"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    VendorName "Dell"
    ModelName "1702FP"
    DisplaySize 337 270
    HorizSync 31-80
    VertRefresh 56-76
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz"
    ### [arg]: arg optional
    #Option "ShadowFB" # [<bool>]
    #Option "KGAUniversal" # [<bool>]
    Identifier "Card0"
    Driver "nvidia"
    VendorName "nVidia Corporation"
    BoardName "NV11 [GeForce2 MX/MX 400]"
    BusID "PCI:1:5:0"
    Option "UseEDIDfreqs=false"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Card0"
    Monitor "Monitor0"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Here's the Xorg.0.log file too:
    X Window System Version 7.1.1
    Release Date: 12 May 2006
    X Protocol Version 11, Revision 0, Release 7.1.1
    Build Operating System: UNKNOWN
    Current Operating System: Linux mythos 2.6.20-ARCH #1 SMP PREEMPT Tue Feb 13 14:51:15 CET 2007 i686
    Build Date: 10 January 2007
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    Module Loader present
    Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    (==) Log file: "/var/log/Xorg.0.log", Time: Mon Feb 19 12:03:44 2007
    (==) Using config file: "/etc/X11/xorg.conf"
    (==) ServerLayout "X.org Configured"
    (**) |-->Screen "Screen0" (0)
    (**) | |-->Monitor "Monitor0"
    (**) | |-->Device "Card0"
    (**) |-->Input Device "Mouse0"
    (**) |-->Input Device "Keyboard0"
    (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi".
    Entry deleted from font path.
    (Run 'mkfontdir' on "/usr/share/fonts/75dpi").
    (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi".
    Entry deleted from font path.
    (Run 'mkfontdir' on "/usr/share/fonts/100dpi").
    (**) FontPath set to:
    /usr/share/fonts/misc,
    /usr/share/fonts/TTF,
    /usr/share/fonts/Type1
    (**) RgbPath set to "/usr/share/X11/rgb"
    (**) ModulePath set to "/usr/lib/xorg/modules"
    (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    (II) No APM support in BIOS or kernel
    (II) Module ABI versions:
    X.Org ANSI C Emulation: 0.3
    X.Org Video Driver: 1.0
    X.Org XInput driver : 0.6
    X.Org Server Extension : 0.3
    X.Org Font Renderer : 0.5
    (II) Loader running on linux
    (II) LoadModule: "bitmap"
    (II) Loading /usr/lib/xorg/modules/fonts/libbitmap.so
    (II) Module bitmap: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
    (II) Loading font Bitmap
    (II) LoadModule: "pcidata"
    (II) Loading /usr/lib/xorg/modules/libpcidata.so
    (II) Module pcidata: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Video Driver, version 1.0
    (--) using VT number 7
    (II) PCI: PCI scan (all values are in hex)
    (II) PCI: 00:00:0: chip 1022,700e card 0000,0000 rev 13 class 06,00,00 hdr 00
    (II) PCI: 00:01:0: chip 1022,700f card 0000,0000 rev 00 class 06,04,00 hdr 01
    (II) PCI: 00:04:0: chip 1106,0686 card 1043,8040 rev 40 class 06,01,00 hdr 80
    (II) PCI: 00:04:1: chip 1106,0571 card 0000,0000 rev 06 class 01,01,8a hdr 00
    (II) PCI: 00:04:2: chip 1106,3038 card 0925,1234 rev 16 class 0c,03,00 hdr 00
    (II) PCI: 00:04:3: chip 1106,3038 card 0925,1234 rev 16 class 0c,03,00 hdr 00
    (II) PCI: 00:04:4: chip 1106,3057 card 1043,8040 rev 40 class 00,00,00 hdr 00
    (II) PCI: 00:09:0: chip 1102,0004 card 1102,0051 rev 03 class 04,01,00 hdr 80
    (II) PCI: 00:09:1: chip 1102,7003 card 1102,0040 rev 03 class 09,80,00 hdr 80
    (II) PCI: 00:09:2: chip 1102,4001 card 1102,0010 rev 00 class 0c,00,10 hdr 80
    (II) PCI: 00:0a:0: chip 1033,0035 card 1799,0001 rev 43 class 0c,03,10 hdr 80
    (II) PCI: 00:0a:1: chip 1033,0035 card 1799,0001 rev 43 class 0c,03,10 hdr 00
    (II) PCI: 00:0a:2: chip 1033,00e0 card 1799,0002 rev 04 class 0c,03,20 hdr 00
    (II) PCI: 01:05:0: chip 10de,0110 card 107d,2834 rev b2 class 03,00,00 hdr 00
    (II) PCI: End of PCI scan
    (II) Host-to-PCI bridge:
    (II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
    (II) Bus 0 I/O range:
    [0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
    (II) Bus 0 non-prefetchable memory range:
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
    (II) Bus 0 prefetchable memory range:
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
    (II) PCI-to-PCI bridge:
    (II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x0008 (VGA_EN is set)
    (II) Bus 1 non-prefetchable memory range:
    [0] -1 0 0xce000000 - 0xcfefffff (0x1f00000) MX[b]
    (II) Bus 1 prefetchable memory range:
    [0] -1 0 0xcff00000 - 0xdf7fffff (0xf900000) MX[b]
    (II) PCI-to-ISA bridge:
    (II) Bus -1: bridge is at (0:4:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
    (--) PCI:*(1:5:0) nVidia Corporation NV11 [GeForce2 MX/MX 400] rev 178, Mem @ 0xce000000/24, 0xd0000000/27, BIOS @ 0xcfff0000/16
    (II) Addressable bus resource ranges are
    [0] -1 0 0x00000000 - 0xffffffff (0x0) MX[b]
    [1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[b]
    (II) OS-reported resource ranges:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    (II) PCI Memory resource overlap reduced 0xe0000000 from 0xefffffff to 0xdfffffff
    (II) PCI Memory resource overlap reduced 0xdf800000 from 0xdf800fff to 0xdf7fffff
    (II) PCI I/O resource overlap reduced 0x0000e000 from 0x0000e003 to 0x0000dfff
    (II) Active PCI resource ranges:
    [0] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [1] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [2] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [3] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [4] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [5] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [6] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [7] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [8] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [9] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [10] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [11] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [12] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [13] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [14] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    (II) Inactive PCI resource ranges:
    [0] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    (II) Active PCI resource ranges after removing overlaps:
    [0] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [1] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [2] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [3] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [4] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [5] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [6] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [7] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [8] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [9] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [10] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [11] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [12] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [13] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [14] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    (II) Inactive PCI resource ranges after removing overlaps:
    [0] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    (II) OS-reported resource ranges after removing overlaps with PCI:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [5] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    (II) All system resource ranges:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [5] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [6] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [7] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [8] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [9] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [10] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [11] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [13] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    [16] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [17] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [18] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [19] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [20] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    [21] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    (II) LoadModule: "xtrap"
    (II) Loading /usr/lib/xorg/modules/extensions/libxtrap.so
    (II) Module xtrap: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension DEC-XTRAP
    (II) LoadModule: "dbe"
    (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    (II) Module dbe: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension DOUBLE-BUFFER
    (II) LoadModule: "record"
    (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    (II) Module record: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension RECORD
    (II) LoadModule: "extmod"
    (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    (II) Module extmod: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension SHAPE
    (II) Loading extension MIT-SUNDRY-NONSTANDARD
    (II) Loading extension BIG-REQUESTS
    (II) Loading extension SYNC
    (II) Loading extension MIT-SCREEN-SAVER
    (II) Loading extension XC-MISC
    (II) Loading extension XFree86-VidModeExtension
    (II) Loading extension XFree86-Misc
    (II) Loading extension XFree86-DGA
    (II) Loading extension DPMS
    (II) Loading extension TOG-CUP
    (II) Loading extension Extended-Visual-Information
    (II) Loading extension XVideo
    (II) Loading extension XVideo-MotionCompensation
    (II) Loading extension X-Resource
    (II) LoadModule: "dri"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    (II) Module dri: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading sub module "drm"
    (II) LoadModule: "drm"
    (II) Loading /usr/lib/xorg/modules/linux/libdrm.so
    (II) Module drm: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org Server Extension, version 0.3
    (II) Loading extension XFree86-DRI
    (II) LoadModule: "glx"
    (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    (II) Module glx: vendor="NVIDIA Corporation"
    compiled for 4.0.2, module version = 1.0.9631
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 0.1
    (II) Loading extension GLX
    (II) LoadModule: "type1"
    (II) Loading /usr/lib/xorg/modules/fonts/libtype1.so
    (II) Module type1: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.2
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
    (II) Loading font Type1
    (II) LoadModule: "freetype"
    (II) Loading /usr/lib/xorg/modules/fonts/libfreetype.so
    (II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
    compiled for 7.1.1, module version = 2.1.0
    Module class: X.Org Font Renderer
    ABI class: X.Org Font Renderer, version 0.5
    (II) Loading font FreeType
    (II) LoadModule: "nvidia"
    (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
    (II) Module nvidia: vendor="NVIDIA Corporation"
    compiled for 4.0.2, module version = 1.0.9631
    Module class: X.Org Video Driver
    (II) LoadModule: "mouse"
    (II) Loading /usr/lib/xorg/modules/input/mouse_drv.so
    (II) Module mouse: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.1.1
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 0.6
    (II) LoadModule: "kbd"
    (II) Loading /usr/lib/xorg/modules/input/kbd_drv.so
    (II) Module kbd: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.1.0
    Module class: X.Org XInput Driver
    ABI class: X.Org XInput driver, version 0.6
    (II) NVIDIA dlloader X Driver 1.0-9631 Thu Nov 9 17:39:58 PST 2006
    (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
    (II) Primary Device is: PCI 01:05:0
    (--) Chipset NVIDIA GPU found
    (II) Loading sub module "fb"
    (II) LoadModule: "fb"
    (II) Loading /usr/lib/xorg/modules/libfb.so
    (II) Module fb: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 1.0.0
    ABI class: X.Org ANSI C Emulation, version 0.3
    (II) Loading sub module "ramdac"
    (II) LoadModule: "ramdac"
    (II) Loading /usr/lib/xorg/modules/libramdac.so
    (II) Module ramdac: vendor="X.Org Foundation"
    compiled for 7.1.1, module version = 0.1.0
    ABI class: X.Org Video Driver, version 1.0
    (II) resource ranges after xf86ClaimFixedResources() call:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [5] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [6] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [7] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [8] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [9] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [10] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [11] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [13] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [15] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    [16] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [17] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [18] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [19] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [20] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    [21] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    (II) resource ranges after probing:
    [0] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [1] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [2] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [3] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [4] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [5] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [6] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [7] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [8] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [9] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [10] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [11] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [13] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [14] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b]
    [15] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b]
    [16] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b]
    [17] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [18] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    [19] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [20] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [21] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [22] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [23] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    [24] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    [25] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b]
    [26] 0 0 0x000003c0 - 0x000003df (0x20) IS[b]
    (II) Setting vga for screen 0.
    (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
    (==) NVIDIA(0): RGB weight 888
    (==) NVIDIA(0): Default visual is TrueColor
    (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
    (**) NVIDIA(0): Enabling RENDER acceleration
    (II) NVIDIA(0): NVIDIA GPU GeForce2 MX/MX 400 at PCI:1:5:0 (GPU-0)
    (--) NVIDIA(0): Memory: 65536 kBytes
    (--) NVIDIA(0): VideoBIOS: 03.11.01.30.00
    (II) NVIDIA(0): Detected AGP rate: 4X
    (--) NVIDIA(0): Interlaced video modes are not supported on this GPU
    (--) NVIDIA(0): Connected display device(s) on GeForce2 MX/MX 400 at
    (--) NVIDIA(0): PCI:1:5:0:
    (--) NVIDIA(0): DELL 1702FP (CRT-0)
    (--) NVIDIA(0): DELL 1702FP (CRT-0): 350.0 MHz maximum pixel clock
    (II) NVIDIA(0): Assigned Display Device: CRT-0
    (WW) NVIDIA(0):
    (WW) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
    (WW) NVIDIA(0): will be used as the requested mode.
    (WW) NVIDIA(0):
    (II) NVIDIA(0): Validated modes:
    (II) NVIDIA(0): "nvidia-auto-select"
    (II) NVIDIA(0): Virtual screen size determined to be 1280 x 1024
    (--) NVIDIA(0): DPI set to (95, 96); computed from "UseEdidDpi" X config
    (--) NVIDIA(0): option
    (--) Depth 24 pixmap format is 32 bpp
    (II) do I need RAC? No, I don't.
    (II) resource ranges after preInit:
    [0] 0 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b]
    [1] 0 0 0xce000000 - 0xceffffff (0x1000000) MX[b]
    [2] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[b]E(B)
    [3] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[b]
    [4] -1 0 0x000c0000 - 0x000effff (0x30000) MX[b]
    [5] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[b]
    [6] -1 0 0xcb800000 - 0xcb8000ff (0x100) MX[b]
    [7] -1 0 0xcc000000 - 0xcc000fff (0x1000) MX[b]
    [8] -1 0 0xcc800000 - 0xcc800fff (0x1000) MX[b]
    [9] -1 0 0xcd000000 - 0xcd003fff (0x4000) MX[b]
    [10] -1 0 0xcd800000 - 0xcd8007ff (0x800) MX[b]
    [11] -1 0 0xdf800000 - 0xdf7fffff (0x0) MX[b]O
    [12] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[b]O
    [13] -1 0 0xcfff0000 - 0xcfffffff (0x10000) MX[b](B)
    [14] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[b](B)
    [15] -1 0 0xce000000 - 0xceffffff (0x1000000) MX[b](B)
    [16] 0 0 0x000a0000 - 0x000affff (0x10000) MS[b](OprD)
    [17] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[b](OprD)
    [18] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[b](OprD)
    [19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[b]
    [20] -1 0 0x00000000 - 0x000000ff (0x100) IX[b]
    [21] -1 0 0x0000a000 - 0x0000a007 (0x8) IX[b]
    [22] -1 0 0x0000a400 - 0x0000a41f (0x20) IX[b]
    [23] -1 0 0x0000d000 - 0x0000d01f (0x20) IX[b]
    [24] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[b]
    [25] -1 0 0x0000d800 - 0x0000d80f (0x10) IX[b]
    [26] -1 0 0x0000e000 - 0x0000dfff (0x0) IX[b]O
    [27] 0 0 0x000003b0 - 0x000003bb (0xc) IS[b](OprU)
    [28] 0 0 0x000003c0 - 0x000003df (0x20) IS[b](OprU)
    (II) NVIDIA(0): Setting mode "nvidia-auto-select"
    (II) Loading extension NV-GLX
    (II) NVIDIA(0): NVIDIA 3D Acceleration Architecture Initialized
    (II) NVIDIA(0): Using the NVIDIA 2D acceleration architecture
    (==) NVIDIA(0): Backing store disabled
    (==) NVIDIA(0): Silken mouse enabled
    (II) Loading extension NV-CONTROL
    (WW) NVIDIA(0): Option "UseEDIDfreqs=false" is not used
    (==) RandR enabled
    (II) Initializing built-in extension MIT-SHM
    (II) Initializing built-in extension XInputExtension
    (II) Initializing built-in extension XTEST
    (II) Initializing built-in extension XKEYBOARD
    (II) Initializing built-in extension XC-APPGROUP
    (II) Initializing built-in extension SECURITY
    (II) Initializing built-in extension XINERAMA
    (II) Initializing built-in extension XFIXES
    (II) Initializing built-in extension XFree86-Bigfont
    (II) Initializing built-in extension RENDER
    (II) Initializing built-in extension RANDR
    (II) Initializing built-in extension COMPOSITE
    (II) Initializing built-in extension DAMAGE
    (II) Initializing built-in extension XEVIE
    (II) Initializing extension GLX
    (**) Option "Protocol" "auto"
    (**) Mouse0: Device: "/dev/input/mice"
    (**) Mouse0: Protocol: "auto"
    (**) Option "CorePointer"
    (**) Mouse0: Core Pointer
    (**) Option "Device" "/dev/input/mice"
    (==) Mouse0: Emulate3Buttons, Emulate3Timeout: 50
    (**) Option "ZAxisMapping" "4 5 6 7"
    (**) Mouse0: ZAxisMapping: buttons 4, 5, 6 and 7
    (**) Mouse0: Buttons: 11
    (**) Option "CoreKeyboard"
    (**) Keyboard0: Core Keyboard
    (**) Option "Protocol" "standard"
    (**) Keyboard0: Protocol: standard
    (**) Option "AutoRepeat" "500 30"
    (**) Option "XkbRules" "xorg"
    (**) Keyboard0: XkbRules: "xorg"
    (**) Option "XkbModel" "pc105"
    (**) Keyboard0: XkbModel: "pc105"
    (**) Option "XkbLayout" "us"
    (**) Keyboard0: XkbLayout: "us"
    (**) Option "CustomKeycodes" "off"
    (**) Keyboard0: CustomKeycodes disabled
    (II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
    (II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
    (II) XINPUT: Adding extended input device "NVIDIA Damage Notification Manager" (type: Other)
    (II) XINPUT: Adding extended input device "NVIDIA Kernel RC Handler" (type: Other)
    (II) XINPUT: Adding extended input device "NVIDIA Event Handler" (type: Other)
    (--) Mouse0: PnP-detected protocol: "ExplorerPS/2"
    (II) Mouse0: ps2EnableDataReporting: succeeded
    Apart from the warnings "No modes were requested ..." and "option "UseEDIDfreqs=false" is not used" nothing looks that bad to me.  Any ideas?  This is what I see in xfce:
    http://img299.imageshack.us/img299/5268 … ot2dk6.png
    I also tried using the gtf output a few times and that didn't work either.  I'm starting to wonder if it's a hardware problem.  Seems kind of subtle for a malfunctioning graphics card though, doesn't it?
    Thanks again

  • Xorg 7 mod / nvidia / libgl-dri conflict

    I run the tesing repo of arch, and want to use xorg modular with nvidia. Although it runs with xf86-input-nv, I'ld like to run the nvidia driver - I think this is the best if you like to have 3D Acceleration, right?
    So, as many have mentioned before, I found that nvidia from testing conflicts libgl-dri, that can't be removed as it is a dependency of mesa. Some advices tend to the direction to just remove mesa and libgl-dri, some say you should'nt.
    I would like to know how I should act now. I have a clean machine, just installed and set up, and don't want to march in the wrong direction.
    Regards

    Hi, Annette. I have forced pacman to remove libgl-dri and ignore dependencies. It works - but I don't know it that is the way one should go. I don't know waht the xorg package becomes in the end, and how the nvidia package will finally fit to modular. Right now, I think it is a hack.

  • [SOLVED] building xorg-server: libgl & nvidia-utils conflict

    Hello!
    I somehow feel like I'm totally missing the point, but...
    edit: although I think (not sure any more) this was the same procedure when I first compiled xorg-server, I maybe should mention, I'm now using the testing xorg.
    I still don't really understand, why I need libgl to build xorg-server. Aren't nvidia-utils supposed to replace that? Is there a way of building xorg-server with nvidia-utils instead of libgl and if yes: are there (dis-/) advantages doing so other than not having to uninstall nvidia-utils while compiling xorg-server?
    Or the other way around: Perhaps it's just me, but I feel "funny" having to remove something that's vital to my installation before I can compile something that's vital to my installation, too... so is it really OK to remove nvidia-utils and compile xorg-server without it or am I doing it wrong?
    Thank you for enlightening me
    Last edited by whoops (2009-04-07 02:20:51)

    Well AFAIK, The nVIDIA closed source drivers haven't caught up with xorg server 1.6 which is why you need libgl to build xorg-xserver 1.6+. I personally perfer the open source drivers over Fglrx (FireGL and Radeon X) and the closed source nVIDIA drivers as well.
    edit: xorg server is 1.6 in testing so if you want to compile from source, and have the closed source nvidia drivers, you would need to compile xorg server 1.5.XX
    P.S. You cannot have both, the nvidia drivers and the open source drivers (libgl), running at the same time which is why the nvidia-* packages are to be removed.
    Cheers!
    Last edited by Neo_The_User (2009-03-30 16:53:28)

  • Problem With Cutom Configuration with Object Type

    Dear Guru's
    I am working WebUI, I am facing a problem with Custom Configuration.
    1. The initial requirement to control the visibility for a dropdown event in ERP Quotation.
    2. To this i copied the default configuration to custom configuration with custom Object type and Subtype.
           CONFIG KEY: ZPJQTN
           OBJECT TYPE: ZOTYP_CONFIG
           OBJECT SUB TYPE:  ZSTYPE_CONFIG1
    3. I have created customm fields in enhancement.
    4. Now i chosen my new configuration (ZPJQTN,ZOTYP_CONFIG,ZSTYP_CONFIG1), when i click Show available fields, the custom fields are not showing. Instead the created fields are available at other configuration.
    5. I am able to control the visibility for the standard available fields.But i am not getting the custom created fields
    (Note:  I have created the Object type and Object sub type as follows: SPRO->CRM->UI Framework->Define Object Types
    Object type: ZOTYP_CONFIG Callback class: ZCL_CONFIG_CALLBACK
    Redifned the method: IF_BSP_DLC_OBJ_TYPE_CALLBACK~GET_OBJECT_SUB_TYPES
    Coded as below:
      data: lv_subtype type bsp_dlc_object_sub_type.
      lv_subtype = 'ZSTYP_CONFIG1'.
      append lv_subtype to result.
      lv_subtype = 'ZSTYP_CONFIG2'.
      APPEND lv_subtype to result.
    Now Please suggest me how to achieve this.
    Also please let me know, whether i am following the correct procedure for controlling the visibility.
    Thanks in Advance,
    S.Meganadhan.

    Hi Harshit,
    I added custom fields using AET only.
    I am able to see the field got added in the structure. I am able to access GET and SET methods of the field.
    But the problem is, it is not getting saved. Am i missed any configuration step?
    Please suggest me.
    Thanks in advance,
    Regards,
    S.Meganadhan.

Maybe you are looking for