XP install probs with SATA drive

I am trying to install XP on a new SATA drive with a new motherboard (MSI 865PE NEO2). I press F6, insert the floppy that came with motherboard, it then seems to install a file (iastor.sys) from floppy. Once this is done it shows that Intel 82801ER SATA RAID CONTROLLER is installed, however when windows tries to continue installing i just get "setup did not find any hard disk drives etc...." press F3 to quit. And thats as far as I get. Please help, I'm getting desperate! It's definately plugged properly and I have tried different cables.

I have the same problem but on a PT880 Neo. I am trying to install Windows XP. I have read on a different site that there isn't a SATA driver on the Windows CD so I need to download them. Is this true? if so where do I get these drivers?
DOH!! I just answered my own question!! Sorry for the spamage. For anyone that needs this info and is using a maxtor drive here is the link.
http://maxtor.custhelp.com/cgi-bin/maxtor.cfg/php/enduser/std_adp.php?p_faqid=1522&p_created=1057008423&p_sid=8ChOP6hh&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MTImcF9zZWFyY2hfdHlwZT1zZWFyY2hfbmwmcF9wcm9kX2x2bDE9NjYmcF9wcm9kX2x2bDI9JnBfY2F0X2x2bDE9ODMmcF9jYXRfbHZsMj0mcF9wYWdlPTE*&p_li=
Have a good install

Similar Messages

Solaris 10 Install problem with SATA drives

Hi, I'm trying to install solaris 10 on a x86 system with 2 SATA drives running in a on board SATA controler (not RAID).
During install the setup fails to detect the disks, to install Windows XP I have to provide disk drivers during the setup procedure by pressing F6 and providing the drivers, alas I cannot seem to find either a way to provide SATA controler drivers to solaris, nor a suitable driver for solaris .
Any help would be extremely apreciated.

I had the same SATA problem on builds 69 and 72 of Solaris10, but the Release version recognises and installs readily on SATA drives on three mainboards that I use. They are Tyan s2875 with dual opteron cpus, Asus k8N-E with a 754 pin athlon64 cpu, and Gigabyte GA-K8NS-939 with a939 pin athlon64.
My Mandrake Linux10 says it sees the SATA drives, but never installed on them.
FreeBSD 5.3 Release for AMD64 sees the SATA and installs with no problems.
Hope this gives you some encouragement to persist

First time install probs with sata raid drive using k7n2g ilsr

hi all!!!
this is the first time i have tried 2 use a sata raid hdd. i dont use a raid drive for my c:, the raid drive is just extra space.
first i formated my pc. i installed the raid drivers, then xp. my pc worked fine. but then after a week it was time 2 try plug the drive in.
when i got my k7n2g ilsr motherboard i di not get a manual. so with the raid drivers installed, i just pluged in the raid drive. the drive seemed fine.... i formatted it and put a couple of games on. but after an hours usage the games would crash (high pitched tone instead of the audio, then full freeze).
i have tried putting these games back on my original drive and they work fine......
anyway....
i wanted 2 know if anyone had any ides what i was doing worng??? are there any settings in the bios that need changing when installing a raid drive????
thanks for any help!!!!!!!

ok still formatting drive..... looking over the files on the msi site for my motherboard it has 2 files available for raid drives:
the 'Promise Serial-ATA RAID Drivers' ( which i have installed)
and the 'Promise Serial-ATA RAID Utility' (which i dont hav installed)
do i need the Promise Serial-ATA RAID utility?? and if so how do i install it?? there are no setup files just dll files like the driver.... is istallation the same as the driver?
again, i thank u for your help!!!!!

How many IDE drives & CDrom can be installed with SATA drives??

How many IDE drives & CDrom can be installed with SATA drives??
i have 2 IDE hard disks & 2 CDROM drives: can install SATA hard disk added to these drives or do i have to remove some???
& if it can be added, can i install 2 SATA drives???
THX in advance

The 3 versions of this board that are available are:
875P Neo-FISR (PCB 2.0)
875P Neo-LSR (PCB 1.0)
875P Neo-FIS2R (PCB 1.0)
All of these boards will have the following ports provider by the chipsets ICH5R south bridge.
2 x SATA (Supporting 2 SATA HDD drives)
2 x PATA (Supporting 4 IDE devices)
All 6 of these can be used at the same time (provided you are using win XP or 2K) you just need to make sure yor BIOS is set right.
->INTEGRATED PERIPHERALS
->ON-CHIP IDE CONFIG
ATA CONFIG: S-ATA ONLY or P-ATA ONLY
S-ATA/P-ATA KEEP ENABLED: YES
OPERATE MODE:
If you set to "legacy mode" S-ATA are set to channel 1 and 2 and P-ATA to channel 3 and 4. If you set to "native mode" P-ATA are channel 1 and 2 and S-ATA 3 and 4. You can only use the raid functionfon SATA in native mode.
If you have the 875P Neo-FIS2R (PCB 1.0) you will also have the following ports provided by the Promise PDC20378 PCI controller:
2 x SATA (Supporting 2 SATA HDD drives)
1 x PATA (Supporting 1 Master IDE HDD drive)
The PATA port is limited to 1 Master HDD by the lite BIOS. This can in theory be upgraded to the full BIOS supporting a master and a slave, but this may obviously void your warranty.
So the answer to your origional question is:
2 x SATA HDDs and 4 x IDE HDD/CDROM if you have 875P Neo-FISR (PCB 2.0) or 875P Neo-LSR (PCB 1.0)
or
4 x SATA HDDs, 1 x IDE HDD (2 if you modify the BIOS) and 4 x IDE HDD/CDROM if you have 875P Neo-FIS2R (PCB 1.0)

How to Install a 2nd SATA drive

Hi,
I asked this before and got many views to my question but no responses, so I thought I would try one more time.
I have a PM G4 Gigabit ethernet and have two ATA drives installed and one SATA drive installed via a SATA PCI card.
What I would like to know is how do you or can you install a second SATA drive on top of the one that's already there? There is room for it to fit on top of the one I have installed, but the sled only provides for one to be mounted. The ATA sled is configured for two.
Any way to get a sled that fits where the SATA drives are installed, or how is that done? My PCI card does have an available SATA connector.
Sorry for the seemingly basic question, but I really don't know the answer.
Thanks,
Bob

Thnaks for the response David. Well, bot do I feel silly. I now see what I somehow never saw before. there is a space in between the ATA driove slots and the SATA drive slot whicvh is where the 4th drive fits. Well, Duuuhhhh?
I have thought of going with a SATA external drive, thing is there are not many SATA external drives out there, also would need a SATA pci card for that. I see that Firm Tek is just now getting into that so I may wait a while. Its' a 160GB SATA drive so it would be a nice addition to backups, testing drives etc.
So what part of Georgia?
Bob

KT4AV will not boot with SATA card installed and no SATA drive

I put a Promise brand SATA II card in a KT4AV motherboard. There is an IDE drive and a DVD drive hooked up to the IDE1 port on the motherboard. That IDE drive has Windows XP Pro SP2 loaded on it.
If I have a SATA drive plugged into the card, the machine works fine. If I remove the STAT drive and leave the card in, I cannot boot to Windows. If I remove the card, it works fine. The only time there is a problem is when the SATA card is plugged in and there is no drive on the SATA card.
As one possible solution, I tried to boot to a Windows CD to reload Windows. It will not even allow me to reload from the CD, it says there is a file missing from the CD. If the SATA drive is hooked up, it will work fine on the CD. Also, I tried multiple CDs and they all give the same message. Because it makes a difference whether the SATA drive is connected or not, I do not believe the CD is the problem.
I have tried looking on Promise's web site for a FAQ or an updated BIOS or for other information about this problem and I found nothing. I have e-mailed them and they did not reply yet.
There is no reason to think this is the fault of the motherboard, but I wanted to see if anyone had any ideas about this problem. Because of the symptoms, I believe it also cannot be the CPU, memory, PSU, video card, etc. Sorry if that makes this post off topic.

Quote from: HenryW on 16-March-07, 02:56:44
Have you tried to disable card in Device Manager when you don't use it? What is the model number of the card you are using?
It is a SATA 300 TX2, which means that it has two SATA ports and one IDE port. I have never used the IDE port, only one SATA.
I have never tried to disable it, but I could try, just to see what it did. It sure would be a lot more work to disable and enable it so that isn't a good long term solution. Among other things, it would mean that I would have to boot up in order to remove the SATA drive. Since it won't boot with the drive removed, it will require more planning.
Will post the results once I have tried. Still no reply from Promise :-(

Cannot use IDE drive with SATA drive

I just installed a 60GB Maxtor Serial ATA hard drive in VIA port 1. However, when I install my previous Maxtor 20GB EIDE hard drive in IDE1, bootup hangs at the "Serial Ch. 0/Ch. 1 device" detection screen.
Is there a trick to this??? I really need the data off my IDE drive. How do I get an IDE drive to exist along side a pre-installed SATA drive?
And does it matter if the IDE drive is set for Master or Slave?

The IDE drive should be set to "master" or "slave" depending on which connector of the cable you're using. The IDE cable included with the board clearly labels which is which.
You didn't say but I'll assume you have a K8T Neo.
If you still cannot get it to work, you should try the Promise controller.

Another "Problem With SATA Drive" thread...

Hey guys, how ya doin'?
Ok, I have a K8N Neo Platinum I got a couple days ago along with all my other parts to buld myself a new system. I got a 120GB Western Digital SATA hard drive. The WD1200JD. I got everything together and plugged in my HD, I turned it on and the HD started making really loud stuttering noises and wouldn't POST or let me get into BIOS. It just stuck at the logo screen. So I unplugged the HD and then it let me into BIOS. I changed the boot order, and made sure that SATA was enabled. The I plugged the drive back in, and it still wouldn't go past the logo screen. Then I messed around a little bit more with boot order and finally got it to POST. I went to install windows XP on it, and the "To install SATA drivers hit F6" screen came up and I hit F6 and nothing happened. It went past that, and got to setup but when I tried to format the drive, it said there was no drive present. I inspected all my BIOS settings and everything seemed to be fine. I think I got a borked Hard Drive.
Any ideas?. Thanks.

Quote
Originally posted by Calculusaurus
Quote
Originally posted by ninjastyle
You shouldn't need to install any drivers or press F6 if you're only using one SATA drive. I really wish MSI would be more clear about this because I get tired of telling people the same thing!!
No need for any floppy disc drive, pressing F6 or installing drivers if using a single SATA drive.
I agree, MSI needs to spell it in bold letters in the manual for its K8N users. It's just to ambiguous for the user to not know this. :(
I think the confusion comes from other chipsets where you DO need to install plain SATA drivers at the F6 prompt even if you use just one SATA drive.

MSI K8T Neo2 issue with SATA drives....

I have a K8T Neo2 motherboard, with a 3700+ San Diego core, running Windows XP Service Pack 2. I don't have the version with the Promise SATA Raid - using the VIA SATA RAID. I am using the latest BIOS (according to the Live Monitor).
The machine was set up (the OS installed) on an IDE 40 gig drive. All was fine, but I noticed that my machine lagged at times (mostly games, under heavy disk load) so I decided to get a couple of Seagate 250 gig drives (they have NCQ, which I know is not supported by this MB, but they were on sale, and I'd read that the drive should still work ok).
I attached the drives, and enabled SATA in the bios. The machine boots fine. I created a single 500 gig striped array using the two new drives. Windows XP sees the array fine, but that I have to initialize it.
Every time I initialize it I get an error that says, "An error has occured" and tells me to check the event log (nothing there), and to either restart the Disk Manager or reboot my computer. The OS actually locks up a few times when I'm doing this (the mouse-cursor freezes).
I've tried using the disks as two single disks, same error (and it reported that they were only 137 gig each, though apparently it's a registry issue, and I used a util to change that setting, but I haven't tested to see if it changed anything.).
I got the latest VIA SATA drives from the MSI site, and installed them (though honestly, WindowsXP saw the card and the drives just fine). One weird thing is that the VIA SATA RAID is listed under SCSI devices in the Device Manager - there is no SATA category in there.
I'm at a loss here. I've searched the web, and this forum, without luck.
Any advice would be appreciated.
*Edit* I just unplugged two IDE disk drives from the computer, and when I started it up again, it found a Promise SATA Raid controller. I thought that wasn't included with the basic version of the board?
David.

Ok - thanks - I read through the stickies and updated my bios tonight to 9.20 (the latest).
Had some dry-mouth moments when WindowsXP decided to "discover" every piece of hardware I had, right down to the mouse, and again when core-center rebooted my computer.
Also, there was some time where my memory (OCZ 2-3-3-6 DDR3200) was being set to CAS2.5, which was kind of weird, but it fixed itself.
Unfort, I am unable to increase my FSB/HTT speed past about 205 before my computer does a reboot.
I have an ATI video card (X800 Plat Ed), and I'd read that some other people had issues with ATI card and the AGP-lock, so I got the CG-ICS950405 clock-gen, and it does state that my AGP is running at 66 (and PCI 33).
Going to bump up my settings via clockgen as soon as I post this (want to post before it potentially crashes).
Should I roll back to the 9.10 bios? Not a lot of discussion on the 9.2, and I'm wondering if it causes some issues.
Thanks again for all the help and info. I used to have a firm grasp on all the components of a system, way back in the P3 days, but things have changed quite a bit...
**EDIT**
Seems to be a Core-Center issue. Used ClockGen to o/c to 2600, with temp nice and low. Will run like this for a bit. Does Core-Center work with a 9.X bios?
I think all my problems are solved - copied a wack of files to my SATA drives, and there were no issues. I won't trust Live Monitor again for drivers or bios - it's still stuck way back at 3.30.
I'll pass the info I've learned off whenever I can.
Comments and criticisms welcome.
David.
Quote from: Puppetman on 26-September-05, 23:23:42
I looked at the motherboard page - they recommend 3.30 unless you have having issues (which I kind of guess I am). Funny that Live Monitor won't pick up those BIOS changes - wonder what else I'm missing.
So 9.1 fixes the AGP/HTT overclocking issue?
The stickies are great - thanks.
David.

MSI NEO 4 Platinum with SATA Drive

I have recently built a new machine with the following specs but I am having problems with system stability in windows and was wondering whether it's because of the way I set up the hard drive.
Specs:
MSI K8N Neo 4 Platinum
AMD Athlon 64 3500 Winchester
Zalman CNPS7000B-Cu
1GB Corsair XMS PC3200 RAM
Sapphire X800 XT
Sound Blaster Audigy Player
Maxtor 80GB Serial ATA Hard Drive
Maxtor 40GB IDE Hard Drive
550W PSU
I plugged my SATA drive into slot 1 and booted from the maxblast 3 CD to partition and set up the hard drive. I then installed windows 98 and upgraded to windows 2000. My system seems to be slow and laggy, though it seems mostly fine in games. When I listen to music and browse a CD at the same time the sound stutters and lags. I am getting lots of slow down when doing lots of things on the computer but it shouldn't slow down as much as it is. I am also getting windows error messages.
Is there a different way I should have installed the hard drive. I can't boot from my windows 2000 disk in dos because it's only upgrade version. I read on the forum about adding the SATA drive to a raid array before installing windows but I don't understand what this means. Can you help?
The floppy drive also doesn't seem to work so I couldn't install SATA drivers at windows setup. How can I get it working because the lead seems to be connected correctly as it gives an error message on boot up with the purple stripe the other side of the floppy drive.

Quote
I can do it with a windows XP upgrade CD surely
yes
Quote
Me Yesterday, 12:55
If you have an XP upgrade CD follow the following steps.
1) Decide which HD you wish to install XP on.
If the Sata - Then turn of PC & unplug IDE Drive, this is a windows thing, as XP will see the Ide drive b4 the Sata & try to create the 1st drive as system drive. You can plug the ide back in when the install is complete.
2) Insert XP Cd. Enter Bios - Advanced bios change boot order so that CD is 1st device. or press f11 as pc posts, & select CD.
3) The PC should now boot from the XP CD.
You don't need to load any floppy drivers.
But XP will ask to see a qualifying product, put in your 2000 or 98 CD.
You should see a Hard drive Partition Setup screen - you can use this to delete any existing partition & format the drive (Don't use the quick format it's only quick cos it dont check for errors so slow & safe is best. See section How to partition and format your hard disk by using the Windows XP Setup program

Installing a single sata drive on a K7N2 Delta M/B

where do I start?
If I run the raid setup, it can see it fine in there right size and eveything, but can't see the drive (or any options for sata) in the bios, or anything relating to it in windows.
Currently running XP with two IDE drives (no raid)
Can I use the sata drive without using the raid?
Does the sata drive have to be the primary drive?
Many thanks
Andy

not sure if this is what yur lookin for but when i first got my raptor, i already had like a 200 gb and a 120 gb ide HD on my k7n2 delta2 plat, so i was like ok reformat time! since i didnt have that much stuff. i just disconnected my 2 ide drives, stuck in my 74gb raptor, and installed windows on that. but you have to be sure all the other drives are discconected while yur doin this. if u have other drives connected, it might now work, i got a boot disk failure at first! i was like lol lets do it again! but yea after i installed windows on the raptor, i just reformatted the other 2 hd's as dump drives. i hope this helps...in some way at least

Z77A-G43 issue with SATA drive

This is wierd
I have 4 Hitachi drives all of 1TB, perfectly working on old PC.
Today have decided to transfer them into new PC:
MB: Z77A-G43
BIOS: 1.20
CPU: Intel g2020
Primary drive is Intel SSD 120G series 330
I have attached 3 HITACHI drives successfully, they are all working fine.
but particular one forces MB to reboot before BIOS screen, last code seen on screen is A2?
Then I have decided to put dedicated controller 1st I took SilImage 3512 SATA/RAID Controller
- no changes computer reboots before post screen
After I took VIA VT6421 SATA/RAID Controller
- no changes computer reboots before post screen
searched web, found nothing useful.
any ideas what might causing this?
EDIT: tested controller SiI3512 on old PC and trouble HDD, everything works just fine :/
read AMIBIOS codes:
0xA0 IDE initialization is started
0xA1 IDE Reset
0xA2 IDE Detect
0xA3 IDE Enable
0xA4 SCSI initialization is started
0xA5 SCSI Reset
0xA6 SCSI Detect
0xA7 SCSI Enable
0xA8 Setup Verifying Password
A2 is ide ? what ide ? I give up.
it seams to me that this board is broken in several ways
- non working DVI
- faulting with valid SATA drive
what else awaits me on this road

Quote from: flobelix on 07-May-13, 04:27:27
using IDE previously and now AHCI might trouble Windows but system would none the less post. At least you should get past IDE detection but hanging at A2 means it doesn't.
I'm wondering about your statement you had been using SilImage 3512 SATA/RAID Controller and VIA VT6421 SATA/RAID Controller. Are these PCI add-on cards? Did you try all SATA ports controlled by the Z77 chipset. Are the drives used are all identical? Is the issue only happening with one particular drive or anytime you attach a fourth hdd no matter which one it is?
About the performance difference from AHCI to IDE the differences are minimal. Should be almost irrelevant for the hdds.
My discoveries:
Using sata mode IDE with windows installed in AHCI mode == windows hangs during loading (BSOD), probably missing drivers or similar.
Also I am unsure what A2 code means but I have noticed it is displayed while bios post screen shows up with the list of installed drives during normal boot.
And is also last code I see when I attach problematic drive resulting in reboot loop.
To be honest I haven't tried all SATA ports on board for sure I haven't tried SATA 1 (1st white) as there is my SSD drive.
But I have tried almost all other ports. I can try them all, but I don't think this will solve the problem.
I don't think problem is in what slot I put my drive, since same behavior is with SATA/RAID controllers.
And whit this SATA/RAID controllers this drive is working perfectly normal on other PC.
No not all drives are identical but I have exactly same drive as this one, and all drives are hitachi:
* HDT721010KLA330 working fine
* HDS721010SLA360 working fine
* HDS721010CLA332 (1) working fine
* HDS721010CLA332 (2) problematic drive == reboot loop (when its single drive or with others).
True I haven't tried to detach Intel SSD and leave problematic drive as only drive in system, I may try this tomorrow)
funny part is that HDS721010CLA332 (2) is working fine when I hot plug it.
Checked firmware version on both drives, and both drives have identical firmwares.
Only difference I know off is that working drive has 1 partition, and problematic drive has 2 partitions.
EDIT: forgot to say it passed SMART test, everything was green (hitachi sw), while hdd sentinel reported 1 bad sector but saying estimated drive working days > 900 days and degree was 98% I am guessing because of that 1 bad sector and too many working days (years) behind him.

Vista to XP downgrade on Lenovo N200 with SATA drive

Hi,
I would like to downgrade my Vista to XP. However doing some research on net I found that XP would not detect a SATA drive, which is the case with me.
Can anyone please tell me what is the best way forward when I have a SATA disk and want to downgrade to XP.
I have read that I would need to change BIOS setting to make it compatible but some have contested this view and mention about d/l drivers. Are there any drivers available to do this ? Has anyone downgraded their N200 to XP?
Also I was thinking of two options
1 - Install XP instead of Vista, which would involve formatting C: and installing XP
2 - Create new partition D: and install XP on D: and have dual boot. This will allow me to switch to Vista in future when most of the s/w would be compatible with it.
Is 2 feasible ?

ashishrulz, welcome to the forum,
have a look at Train500's excellent post about downgrading an N100, the only difference will be some drivers which you can download here after choosing your correct model type.
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Mirroring with SATA Drives on a PwrMac G4

I've got a MDD G4 circa 2002 with two 250gb drives...one the main drive the other the backup. I rapidly running out of space.
Been considering moving to dual 500-750gb SATA drives with a Sonnet Tempo Serial ATA controller and configuring them in Mirror (RAID 1) mode using Disk Utility.
My questions are:
1) Will this work
2) Will I be able to boot off this "drive".
3) Are there any traps that I may be running into.
Appreciate any feedback...Chris

Hi-
The Sonnet tempo SATA controller is bootable from any attached drive (important feature that not all have), and a Mirror set can be used for startup in OS 10.3 and later.
http://docs.info.apple.com/article.html?artnum=106594
Only trap is you'll still need a third, external HDD of 500-750gb capacity to backup your mirror. Don't neglect that.....

Install issue with CD drives / and burning

I am running Windows Vista 64 on a new computer I built (latest ASUS P5K-E with a quad Q6600 cpu and 4gigs of RAM). I transferred all my music and installed iTunes. Everything is working fine except for the burning of disks. It did give me a prompt at the end of the iTunes install and on first startup that there may be a problem recognizing the CD drives. However, there is no problem importing music on those CD/DVD burner drives -- but I cannot burn on those drivers. I can burn using other software on these drives -- no issues with the drives at all. Under iTunes "Preferences", and 'Burning' it states "No supported Disk burners found". Both are Lite-on CD/DVD burner drives and less than a year old -- and of course worked on the old XP computer with iTunes. I have uninstalled, reinstalled iTunes -- no luck. Any ideas? This looks to be something in the Registry on install, but not sure what to do. Any help appreciated.

You may need the CD Configuration folder too, after you install the drivers.
Here is the CD Configuration folder, with the Files you need Just Unzip it and place the CD Configuration Folder into Your C:\Program Files (x86)\iTunes Directory
http://stahlhammer89.com/apple/CD_Configuration.zip
I had my friend with Windows Vista x86 Install iTunes and give me the Folder and Files I needed.
Hope this helps you

XP install probs with SATA drive

Similar Messages

Maybe you are looking for