XP + KT3 +USB = dead Windows event sounds

KT3 MS-6380e ver1 (USB + SOund card event fails)
New motheboard , new Op SYS.
I discovered why the sound card windows
events fail to runUnder XP
First the USB chip is unknown to XP
so you must load the Via VT8235 chip drivers.
getem at Via.com...
When they load ,you will notice that
1- All sounds work, wav, mp3 ,ect.
2- that all windows events ,like Ding.wav
for critical stop ,are all dead. All Events.
3- then when you use your first USB device, mine was the SANDISK smartmedia device.
As soon as it is loaded and working , magically
the event codes are up and functioning.
This happen on both an upgrade to XP and also
a full virgin install.
:D

Quote
Originally posted by jelly
KT3 MS-6380e ver1 (USB + SOund card event fails)
New motheboard , new Op SYS.
I discovered why the sound card windows
events fail to runUnder XP
First the USB chip is unknown to XP
so you must load the Via VT8235 chip drivers.
getem at Via.com...
When they load ,you will notice that
1- All sounds work, wav, mp3 ,ect.
2- that all windows events ,like Ding.wav
for critical stop ,are all dead. All Events.
3- then when you use your first USB device, mine was the SANDISK smartmedia device.
As soon as it is loaded and working , magically
the event codes are up and functioning.
This happen on both an upgrade to XP and also
a full virgin install.
:D
did you check to see if windows deafault was in the window or no sounds or blank in the sounds drop down list? because sometimes that is it also

Similar Messages

How can I disable the event sound played when a new window is opened?

When Firefox starts, or when a new window is opened there is an annoying click.
How can I disable this?
The only way I have been able to stop it is by disabling all event sounds from the control panel but I'd rather just disable this particular sound.

No, it's Windows XP. Hmmm, I don't know! I only started noticing it recently and as far as I remember, the only new add on is NoScript. I found the event that was being triggered (Start Connection) and disabled the sound in Windows. So the problem is solved in that I don't have the annoying sound ... but don't know why it started and hope nothing sinister is going on.

When I restart my computer and hold the option key after creating a bootable usb with windows 7 and partitioning only the original partition shows up. Not the windows one or the bootable usb.

     Okay so first things first this isn't the newest macbook pro. When I open about my mac and go to system report it says it is a Macbook Pro 3,1 and the Boot Rom Version say MBP31.0070.B07. Originally when starting up Boot Camp Assistant there where only two options, the "create windows 7 bootable usb" was not there at all. So after some editing and helpful tutorials I was able to get the option show up and created a bootable usb with windows 7 and downloaded the support software onto a separate flash drive. Finally I did the last step and created a second partition for windows. Once the process is complete my computer automatically restarts.
     This is where the problem is. Once my computer makes the booting up sound it doesn't load up windows it gets stuck on a apple logo as if it's trying to reastart normally and can't. So I shut down and this time I hold down the option key during start up. It brings up the main partition and some recovery thing but no windows partiton and no bootable usb.
     I forgot to mention that I am running OS X 10.9.3. Okay any body want to help me out? Iv'e been at this for hours and can't get an inch closer to having windows. Please and thank you!
P.S. If I missed a discussion that answer my question just point me to it. Iv'e been looking for a while, but who knows i might have missed one.

The only known way to make it work on an external drive is by first installing Windows onto an internal drive, then cloning the install to an external Thunderbolt drive. Thunderbolt is seen as an extension of the internal bus, so Windows doesn't see it as an external device.

I am using iMac OS 10.7.2 with Garageband'11 6.0.4. I can't record sound from mixer Behringer X1622USB using USB out. when I connect the mixer to iMac via USB appears USB Audio CODEC on Sound and preferences but no sound from mixer to iMac. Need help.

I am using iMac OS 10.7.2 with Garageband'11 6.0.4. I can't record sound from mixer Behringer X1622USB using USB out. when I connect the mixer to iMac via USB appears USB Audio CODEC on Sound and Preferences but I can't get no sound from mixer to iMac only sound from iMac to mixer. I only can record sound using microphone line in. Please help.

Eric,
Thanks for your reply. Realtek audio works only in playback. There is a stereo mix in the mixer but the recording controls are not operable with no sliders in the mixer for any recording option. Slider controls appear to be grayed out. Can't figure out how to enable them. Downloaded newest drivers to no avail.
The M Audio control panel has no apparent option for recording stereo mix. Adobe ignores the sound from the DVD or CD and shows flatline.
I'm trying to record the sound from the DVD not rip the track.
When I go to Audio Driver Setup and select Audition 3.0 windows sound, there is no input device installed.
I'm thinking of going back to a decent internal Soundblaster card like I have on my 8 year old machine I am replacing.

SB Live ! 24 bit external USB and windows seven blue screen

;SB Li've ! 24 bit external USB and windows seven blue screen+ hi! i have installed windows seven 64 bit build 7600 RTM on my PC and i wanted to install also my USB sound card which is SB Li've ! 24 bit and i downloaded the beta drivers from creative. instalation was really fast and smooth but at the end i've got a message that the program has stopped to response and i have closed it. i did a system reboot and i have seen that the sound card has been installes succesfull and also the control panel. Sound was clear and really nice, all worked fine but sometimes im getting a blue screen on my windows with a code STOP 0x000000E and then a file named usbuhc.sys was the problem. i think that the sound card is the thing that is doing the blue screen becouse i have only a keyboard, mouse and the sound card SB Li've ! installed as USB.
Is it normal that i have those troubles on my PC ? is it my sound card my windows seven problem ? what should i do now ?
at the moment i have turned off the sound card so i will see if i get a blue screen or not.
thanks for any reply

? yes, i have also tried to download the beta drivers again and re-install them but i have still the same problem :/ it happens in a different time, sometimes after hour or sometimes after 0 hours when my computer is turned on. my system is mostly turned on becouse im downloading some stuff so it is running all the day, sometimes im surfing websites but its nothing special. I really dont know what to do :/@83.30.93.77

USB DEAD

hello
i got a HP Pivillion dv6 1055ee and the usb ports dead, i tried
installing win 7 64bit: DEAD.
tried upgrading the firmware: DEAD
tried to boot from usb: DEAD
tried diffrent drivers: DEAD
tried diffrent usb devices: DEAD
tried what the forum suggested: DEAD
it doesnt read the usb in win or from the bois
what else should i try?
tthank you

Do you mean the usb ports on both sides of the notebook?
In device manager do you see universal serial bus controllers as being present?
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Lots of Anyconnect Error Message in Windows Event Log

Hi Community.
We have lots of Anyconnect Error Messages in the Windows Event Log. Following two examples.
Can anyone tell me why these errors appears and how do I fix them ? I already installed the newest Anyconnect on my machine.
Thanks in advance and Kind Regards Patrick
Example 1
<Provider Name="acvpnagent" />
<EventID Qualifiers="9216">2</EventID>
<Keywords>0x80000000000000</Keywords>
<EventRecordID>97564</EventRecordID>
<Channel>Cisco AnyConnect Secure Mobility Client</Channel>
- <EventData>
<Data>Function: CNetEnvironment::logProbeFailure File: .\NetEnvironment.cpp Line: 1432 Invoked Function: CHttpProbeAsync::SendProbe Return Code: -27066354 (0xFE63000E) Description: HTTP_PROBE_ASYNC_ERROR_CANNOT_CONNECT HTTP (host: 109.164.211.237)</Data>
</EventData>
Example 2
<Provider Name="acvpnagent" />
<EventID Qualifiers="9216">2</EventID>
<Keywords>0x80000000000000</Keywords>
<EventRecordID>97565</EventRecordID>
<Channel>Cisco AnyConnect Secure Mobility Client</Channel>
- <EventData>
<Data>Function: CNetEnvironment::TestAccessToSG File: .\NetEnvironment.cpp Line: 1385 Invoked Function: CNetEnvironment::analyzeHttpResponse Return Code: -28966899 (0xFE46000D) Description: NETENVIRONMENT_ERROR_PROBE_INCOMPLETE:Network Probe could not contact target</Data>
</EventData>

HI and welcome to Discussions,
in my personal opinion there is not much for you to worry about.
The 'Windows Tool for the elimination of malware' is nothing you miss as long as you have a decent Anti-Virus Software running.
The update for the IE 7 might be missing an installed IE 7, which can do by downloading it yourself from Microsofts webpage.
If you don't use the IE but something like Firefox or Opera or Safari, than don't bother with these update.
Stefan

How to write to windows event logs from determinations-server under IIS

This is just an FYI technical bit of information I wish someone had shared with me before I started trying to write OPA errors to the windows event log... Most problems writing to the windows event log from log4net occur because of permissions. Some problems are because determinations-server does not have permissions to create some registry entries. Some problems cannot be resolved unless specific registry entry permissions are actually changed. We had very little consistency with the needed changes across our servers, but some combination of the following would always get the logging to the windows event log working.
To see log4net errors as log4net attempts to utilize the windows event log, temporarily add the following to the web.config:
<appSettings>

<add key="log4net.Internal.Debug" value="true"/>
</appSettings>
<system.diagnostics>
<trace autoflush="true">
<listeners>
<add
name="textWriterTraceListener"
type="System.Diagnostics.TextWriterTraceListener"
initializeData="logs/InfoDSLog.txt" />
</listeners>
</trace>
</system.diagnostics>
To add an appender for the windows event viewer, try the following in the log4net.xml:
<appender name="EventLogAppender" type="log4net.Appender.EventLogAppender" >
<param name="ApplicationName" value="OPA" />
<param name="LogName" value="OPA" />
<param name="Threshold" value="all" />
<layout type="log4net.Layout.PatternLayout">
<conversionPattern value="%date [%thread] %-5level %logger [%property{NDC}] - %message%newline" />
</layout>
<filter type="log4net.Filter.LevelRangeFilter">
<levelMin value="WARN" />
<levelMax value="FATAL" />
</filter>
</appender>
<root>
<level value="warn"/>
<appender-ref ref="EventLogAppender"/>
</root>
To put the OPA logs under the Application Event Log group, try this:
Create an event source under the Application event log in Registry Editor. To do this, follow these steps:
1.     Click Start, and then click Run.
2.     In the Open text box, type regedit.
3.     Locate the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Eventlog\Application
4.     Right-click the Application subkey, point to New, and then click Key.
5.     Type OPA for the key name.
6.     Close Registry Editor.
To put the OPA logs under a custom OPA Event Log group (as in the demo appender above), try this:
Create an event log in Registry Editor. To do this, follow these steps:
1.     Click Start, and then click Run.
2.     In the Open text box, type regedit.
3.     Locate the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Eventlog
4.     Right-click the eventlog subkey, point to New, and then click Key.
5.     Type OPA for the key name.
6.     Right-click the new OPA key and add a new DWORD called "MaxSize" and set it to "1400000" which is about 20 Meg in order to keep the log file from getting too large.
7.     The next steps either help or sometimes cause an error, but you can try these next few steps... If you get an error about a source already existing, then you can delete the key.
8.     Right-click the OPA subkey, point to New, and then click Key.
9.     Type OPA for the key name.
10.     Close Registry Editor.
You might need to change permissions so OPA can write to the event log in Registry Editor. If you get permission errors, try following these steps:
1.     Click Start, and then click Run.
2.     In the Open text box, type regedit.
3.     Locate the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Eventlog
4.     Right-click the EventLog key, select Permissions.
5.     In the dialog that pops up, click Add...
6.     Click Advanced...
7.     Click Locations... and select the current machine by name.
8.     Click Find Now
9.     Select both the Network user and IIS_IUSERS user and click OK and OK again. (We never did figure out which of those two users was the one that fixed our permission problem.)
10.     Change the Network user to have Full Control
11.     Click Apply and OK
To verify OPA Logging to the windows event logs from Determinations-Server:
Go to the IIS determinations-server application within Server Manager.
Under Manage Application -> Browse Application click the http link to pull up the local "Available Services" web page that show the wsdl endpoints.
Select the /determinations-server/server/soap.asmx?wsdl link
Go to the URL and remove the "?wsdl" from the end of the url and refresh. This will throw the following error into the logs:
ERROR Oracle.Determinations.Server.DSServlet [(null)] - Invalid get request: /determinations-server/server/soap.asmx
That error should show up in the windows event log, OR you can get a message explaining why security stopped you in "logs/InfoDSLog.txt" if you used the web.config settings from above.
http://msdn.microsoft.com/en-us/library/windows/desktop/aa363648(v=vs.85).aspx
Edited by: Paul Fowler on Feb 21, 2013 9:45 AM

Thanks for sharing this information Paul.

Window.event does not working in Firefox 4.0 and also window.event.ctrlKey ?

hi,
I'm using Microsoft virtual earth map 6.2 (bing Map) in my application.On map showing number of images.On Each image there is onClick event that select image if user press left mouse button while holding Ctrl key .For this I wrote java-script function where I'm using Window.event.button (To check mouse button) and window.event. ctrlKey(To check control key) But these both are not working in Firefox 4.0 ,the same is working in Firefox 3.6X version perfectly.
Thanks

The same problem is in Firefox 5.0 version too

Operations Manager Failed to Access the Windows Event Log and management server is showing warning state

Hi,
I am monitoring AD server from SCOM 2012 R2. My management server goes into waning state. When i run Health explorer then it come back in the healthy state but after some time it again goes into warning state. After seeing alert i found that a alert is coming
again and again i.e. Operations Manager Failed to Access the Windows Event Log.The description of alert is mention below
The Windows Event Log Provider is still unable to open the DhcpAdminEvents event log on computer 'nc2vws12ad5.corp.nathcorp.com'.
The Provider has been unable to open the DhcpAdminEvents event log for 64080 seconds.
Most recent error details: The RPC server is unavailable.
Please suggest me how to resolve this so that my management server will again come back in healthy state.
Thanks
Abhishek

Hi Abhishek,
As i mentioned earlier the Alert resolution says the same points.
Can you give details on the below ?
Is there really a log named "Dhcpadminevents" in the MS's Event viewer ?
Did you recently configure any new alert where you mentioned "Dhcpadminevents"
as a event log location ?
If yes then what is the target you selected for the rule / monitor there ?
Can you post the results for analysis ?
Gautam.75801

While Installation of 11g database creation time error ORA-28056: Writing audit records to Windows Event Log failed Error

Hi Friends,
OS = Windows XP 3
Database = Oracle 11g R2 32 bit
Processor= intel p4 2.86 Ghz
Ram = 2 gb
Virtual memory = 4gb
I was able to install the oracle 11g successfully, but during installation at the time of database creation I got the following error many times and I ignored it many times... but at 55% finally My installation was hanged nothing was happening after it.....
ORA-28056: Writing audit records to Windows Event Log failed Error and at 55% my Installation got hung,,,, I end the installation and tried to create the database afterward by DBCA but same thing happened....
Please some one help me out, as i need to install on the same machine .....
Thanks and Regards

AAP wrote:
Thanks Now I am able to Create a database , but with one error,
When I created a database using DBCA, at the last stage I got this error,
Database Configuration Assistant : Warning
Enterprise Manager Configuration Failed due to the Following error Listener is not up or database service is not registered with it. Start the listener & Registered database service & run EM Configuration Assistant again....
But when I checked the listener was up.....
Now what was the problem, I am able to connect and work through sqlplus,
But I didnt got the link of EM and when try to create a new connection in sql developer it is giving error ( Status : failure - Test Failed the Network Adapter could not establish the connection )
Thanks & Regards
Creation of the dbcontrol requires a connection via the listener. When configuring the dbcontrol as part of database creation, it appears that the dbcontrol creation step runs before the dynamic registration of the databsase with the listener is complete. Now that the database itself is completed and enough time (really, just a minute or two) has passed to allow the instance to register, use dbca or emca to create the dbcontrol.
Are you able to get a sqlplus connection via the listener (sqlplus scott/tiger@orcl)? That needs to be the first order of business.

Urgent help needed on writing errors in to windows events application logs

Hi all,
we have web based application. Whenever there is critical errors encounters in our application we need to write that errors in to windows
event viewer, application logs. Please help me on how to do this.
do we have any specific API for this ?
thanks in advance
Shivakumar

You should use WinAPI to do so. Asking in JNI forum (or specialized WinAPI forum) for more details is good idea I think.

Illustrator CC crashes on startup(windows event viewer message included)

Windows event viewer shows like this...
System
Provider
[ Name]
Application Error
EventID
1000
[ Qualifiers]
0
Level
2
Task
100
Keywords
0x80000000000000
TimeCreated
[ SystemTime]
2013-12-09T06:35:08.000000000Z
EventRecordID
71639
Channel
Application
Computer
HPNB-dhleeNB
Security
EventData
Illustrator.exe
17.0.0.260
52822426
ntdll.dll
6.1.7601.18247
521ea8e7
c0000374
000ce753
a690
01cef4a8afb2dd09
C:\Program Files (x86)\Adobe\Adobe Illustrator CC\Support Files\Contents\Windows\Illustrator.exe
C:\Windows\SysWOW64\ntdll.dll
0b8a3ab7-609c-11e3-8e0d-005056c00008
Please help.

Problem solved.   Refer to below.
3 posts
Nov 25, 2013
2.AlanDrVita,
Nov 26, 2013 9:16 AM   in reply to outdoorz
Report
I may have been able to resolve my issue. I held shift while opening Illustrator and opened it in a bare bones mode, then closed it and reopened it without getting the error message. Good luck to you.
Was this helpful? Yes   No

Error in starting nidevldu and nipxirmu services (windows event viewer)

A computer running Windows XP SP1 and a Visual basic (V6.0) application that I've developped had crashed several times. I've seen lots of errors in the Windows event viewer saying that the nidevldu and nipxirmu services were trying to start (exact french message : Le service nidevldu est en attente de démarrage et Le service nipxirmu est en attente de démarrage). These messages are real errors (not warning or informations).
I use a 6034E PCI card, Visual basic V6.0 and NI-DAQ 7.4.
The crashes I've seen may be linked with this problem.
Is there a solution?

Hi,
I think that you are not going to be starting and stopping the devldu service in normal circumstances... due to crashes !
The firsts steps you have to focus on is to optimize your program in order to avoid crashes, which is not a normal way of work I guess. Then you will be able to avoid these messages!
Regards,
David D. - Application Engineer - NI

Can't be modify the value of window.event.keyCode in IE 11(Windows 7 Premium) where as in IE 8 (Windows XP) its working fine

The following is the sample code whcih I have used to check.<%@ page language="java" contentType="text/html; charset=ISO-8859-1"
pageEncoding="ISO-8859-1"%>
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN" "http://www.w3.org/TR/html4/loose.dtd">
<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=ISO-8859-1">
<title>Sample Form</title>
<script type="text/javascript">
function keyDownEvent() {
alert("KD:"+window.event.keyCode);
window.event.keyCode=0;
alert("KD:"+window.event.keyCode);
function keyPressEvent() {
alert("KP:"+window.event.keyCode);
window.event.keyCode=0;
alert("KP:"+window.event.keyCode);
</script>
</head>
<body>
<form>
<input type="text" onkeydown="keyDownEvent()" onkeypress="keyPressEvent()" />
</form>
</body>
</html>
Kindly post your answers, am waiting for answers...

This is the TechNet Forum for questions regarding
Internet Explorer 8, 9, 10, 11 for the IT Pro Audience. Topics covered are: Installation, Deployment, Configuration, Security, Group Policy, Management questions.
For better assistance please ask for help in the MSDN
IE Development Forums.
Thanks & Regards,
Vincenzo Di Russo
Microsoft® MVP Windows Internet Explorer, Windows & Security Expert - since 2003.
Moderator in the Microsoft Community and TechNet Forums
My MVP Profile

XP + KT3 +USB = dead Windows event sounds

Similar Messages

Maybe you are looking for