Xp_logininfo "Installation problem on windows 2003 with Sql 2005"

Hi every one
I am facing a problem during the installation of Solution Manager 4.0 on Windows 2003 server with Ms Sql 2005, I received the following error
Msg 15404, Level 16, State 19, Procedure xp_logininfo, Line 60.
Its some how look likes that the user "SID"ADM
Can any one give me a clue
thanks
Kind Regards
Sohail

Hi All,
This would solve your problem
First of all this error is MSSQL error.
When you perform an action on an instance of SQL Server that requires SQL Server to resolve the credentials of a Microsoft Windows NT domain user account, you may receive an error message that is similar
Server: Msg 8198, Level 16, State XX, Procedure <Stored Procedure Name>, Line <line Number>
Could not obtain information about Windows NT group/user '<Domain\Account Name>'.
To resolve the credentials of a Windows NT domain user account, SQL Server uses the xp_logininfo system stored procedure. Here is a list of the common scenarios where you may notice that the xp_logininfo system stored procedure fails and causes the 8198 error.
When you use an xp_sendmail extended stored procedure.
When you set up replication.
When you run a SQL Server Agent job.
SQL Server may run the xp_logininfo system stored procedure to retrieve information about the Windows domains and the user accounts, even if the user does not do so explicitly. Therefore, if you receive an 8198 error message and the error message mentions the xp_logininfo system stored procedure as the procedure, you must use SQL Profiler to trace and to troubleshoot the exact point of failure.
You can go through this link for more info...
http://support.microsoft.com/?kbid=834124
Feel Free to Revert back...
--Thanks and Regards,
Ragu
ERP,
Suzlon Energy Limted, Pune
Extn: 2638
+919370675797
I have no limits for others sky is only a reason

Similar Messages

B1i (2005) installation failedSo far: windows XP, MS-SQL 2005 express: ok

Dear All,
I try to install B1i for NW 2005 on a SBO 2005B installation. I have installed all prerequisites like JDK, MSXML, Tomcat (no blanks in path). When running the setup program and after all information gathered, the connection to the MS-SQL 2005 database succeeds and the final installation step starts but returns the message:
"Initail database failed, make sure Tomcat or mini-http is shut down and please check your database's status and try again"
Looking into MS-SQL shows a database beeing created named localhost/B1i. Tomcat and mini-http are definately shut down. When starting Tomcat, it is accessible via http://localhost:8080.
System Parameters:
windows server 2003
SBO 2005B
java: 1.4.2.19
tomcat 5.5.27 including compat package for 1.4.2.19)
sql jdbc 1.2.2828.100
msxml 4.0 SP 2
I can not find an error in the system. Is there a way to diagnose what is happening and does anyone have an idea where the problem lies?
Ciao, Mathias
[Update]
I have tried JDBC 2.0.1008 and JDBC 2.0.1607 - both lead to a fatal error when trying to connect to the database. I assume this is due to Java JDK 1.4.2 as JDBC requires Java 5.0 (1.5.0)
Does anybody know if I can use JDK 1.5.0_17 instead of 1.4.2_19?
[Update 2]
I have tried to install the B1i on two other servers with identical setup and it worked. However, this will not help me with this machine... On the other side, it shows, that there is nothing wrong with the procedure I am using
I found by the way: B1i works fine with MSSQL 2005 Express, it works with jdk 1.5.0.17 (and then JDBC 2.0)
[Update 3]
So far:
windows XP, MS-SQL 2005 express: ok
windows XP, MS-SQL 2005 express, SBO2005A: ok
windows 2003, MS-SQL 2005 SBO2005A: fail
windows 2003, MS-SQL 2005 SBO2005B: fail
windows 2003, MS-SQL 2005 SBO2007A: ok
windows 2003, MS-SQL 2005 Netweaver 2004S: fail
Unfortunately the three servers where it fails are the ones I need to use for production
The precise error state is that the install routine creates the database in SQL 2005 and then reports that it can not create the database. Is there something I should check in SQL 2005?
Edited by: Mathias Wilhelm on Feb 11, 2009 5:17 PM

Salut Eddy,
I tried it with tomcat 5.0.30 - no success. JDK is 1.4.2.19
I tried it with tomcat 5.5.27 - no success. JDK was 1.4.2.19 and 1.5.17
I checked the database: The structure is created but the tables are not created. As the user 'sa' has full admin rights it must be with the access path to the database that is wrong. What I do not understand is, why the installation routine is able to connect to the database to create B1i and then unable to create the tables. I checked in the log files of the db and found no error messages. I tested this as well by using a wrong password for sa or a wrong user. In both cases, the installation routine fails already when checing the existence of B1i database
[Update]
In the meantime:
Checked permissions on database
Checked that administrator is member of local admin group
Checked JAVA_HOME environment variable
Found collation SQL_Latin1_General_CP1_CI_AS for working setup and SQL_Latin1_General_CP1_CS_AS in failing setup
Checked all security settings by comparing to working setup
Checked event viewer and found no errors
Checked all log files and found no errors
Checked that sa can create tables manually in localhost\B1i
Ciao, Mathias
Edited by: Mathias Wilhelm on Feb 12, 2009 2:36 PM

Installation problem on Windows 2003

Hi All,
I have installed the saprfc extension on my laptop for testing purposes.
Definitions of my laptop: Windows XP, IIS 6, PHP 4.4.2, SAP GUI 640
Everything works fine and I can access the SAP through the web server on my laptop without any problem.
Now, after finishing my tests I installed my web application on a real production server with the following definitions: Windows 2003 server, IIS 6, PHP 4.4.2
As you can see the two differences are the operating system and the fact that I do not have a complete SAP GUI installation on the server I only located the librfc32.dll under the windows library.
My problem is that I get the message that the php_saprfc.dll extension cannot be loaded (I edited the php.ini).
Doe anyone have any idea why?
Thanks,
Roy

Hi,
I have an installation with my laptop WIN2003 server with apache web server instead of IIS, without problems.
Are you sure that in your php.ini is all OK?
Have you tried to copy the WIN2003 php.ini on your laptop and try to load saprfc.dll?
Lorenzo

N1 SPS 6.0 Installation problem on windows 2003

Hello,
I have tried to install N1 SPS 6.0 on windows 2003. I was able to finish installlation successfully. But When I try to access tool from http://localhost:8080 , It is not working. I am new to tool , I am installing first time so not able to figure out. I have checked the service for master server is starting under windows services. What else do I need to check? Are there any prerequisite to install N1 SPS 6.0 Master Server on windows?
Thanks. Any help will be appreciated.
Thanks
Bhavika

1. While installation did you configured http or https for UI ? I configured http
2. If https, did you provided the keystore file as part of installation or not? No
3. If https and opted to provide the keystore file after the installation? No
4. if you run 'netstat -an | more' can you find port 8080 in the list? I cannot see
5. are you finding any error messages in {install-dir}\server\bin\cr_server.out file? if so, can you share that error message
I cannot see cr_server.out file under C:\Program Files\N1 Service Provisioning System\6.0\server\bin that is my install directory
6. Related to N1 SPS, are you finding any errors in windows event log? if so, can you share the error message
7. From DOS command prompt, when you run "net start crserver60" or "net start postmaster60" or "net start crprepdb60" are you getting the following error? *
The requested service has already been started.
I see following message
C:\Documents and Settings\Administrator>net start crserver60
The N1 Service Provisioning System 6.0 Server service is starting.
The N1 Service Provisioning System 6.0 Server service was started successfully.
8. Do you have the local user postgres in your system What do u mean by local user ? I have installed postgres on my system with postgres user.
9. instead of using "http://localhost:8080", if you try to access the UI admin through "http://{windows-host-name}:8080", does it work? * I tried both way , it does not work *

Oracle EBS R12 installation problem in Windows 2003

Hi,
I am trying to install Oracle EBS R12 on Windows 2003 R2. I have installed cygwin along with required packages and also Visual studio 2005 as specified in the prerequisites of installation document.
All the validations are successful before installation but I am facing error during installation in Step3 at about 53 percent. When i checked the log file, I found that some of the files required for installation are not found in my staging area. Now I want to run MD5sum on the Staged Files.
I had downloaded md5sum_windows.txt and also run this command :
md5sum --check md5sum_Windows.txt > md5sum_result.txt
In md5sum_result.txt, I am getting error for all files. Error message is as :
oraAppDB\Disk1\data\driver\Disk1.drv
: FAILED open or read
This is repeating for all files. But i can see that the files are present in My Staging area. Do i need to set some permission for this. Please help. Desperately want to install EBS as part of perparation for my planned certification.
Edited by: 855292 on Nov 26, 2011 1:58 AM
A simple detailed Step by Step Installation Document or any good reference for the same would by really appreciated.
Edited by: 855292 on Nov 26, 2011 2:00 AM

I have downloaded all the 33 files in oracle edelivery site. I have seen a post of yours regarding Oracle R12 installation on Windows XP. It mentions only some 25 files. Please do not rely on the that thread as it was for 12.0.x installation.
For R12 (12.1.1) you need to download the following files:
From: Oracle E-Business Suite Release 12.1.1 Rapid Install Start Here (Part 1 of 4)
To: Oracle E-Business Suite Release 12.1.1 for Microsoft Windows (32-bit) Rapid Install APPL_TOP - Disk 2 (Part 2 of 2)
Is it possible that contents of the zip file are lost during download because my stage area is about 39 GB . and also I have verfied all the files in edelivery site is downloaded too.
Also the error i mentioned in my last post, I can see the file in the directory but still its showing read error. Is it due to corruption of data. That would mean that I will have to download all 40 GB again :-(It is easy to verify the contents of the stage area directory without running md5sum, so please do so and post the results here.
Thanks,
Hussein

10g R2 Client Installation Problem on Windows 2003 64 bit itanium

Hi,
When I click on the setup.exe, i am getting the following..and not getting setup screen
Using paramFile: E:\oracle_client\10g_winIA_client_102010\client\install\oraparam.ini
No pre-requisite checks found in oraparam.ini, no system pre-requisite checks will be executed.
The commandline for unzip:
E:\oracle_client\10g_winIA_client_102010\client\install\unzip -qqq ../stage/Components/oracle.swd.jre/1.4.2.8.0/1/DataFiles/"*.jar" -d "C:\DOCUME~1\SBOLLI~1\LOCALS~1\Temp\1\OraInstall2008-04-22_03-44-38PM"
The commandline for unzip:
E:\oracle_client\10g_winIA_client_102010\client\install\unzip -qqq ..\stage\Components\oracle.swd.oui\10.2.0.1.0\1\DataFiles\/"*.jar" -d "C:\DOCUME~1\SBOLLI~1\LOCALS~1\Temp\1\OraInstall2008-04-22_03-44-38PM"
The commandline for unzip:
E:\oracle_client\10g_winIA_client_102010\client\install\unzip -qqq ..\stage\Components\oracle.swd.oui.core\10.2.0.1.0\1\DataFiles\/"*.jar" -d "C:\DOCUME~1\SBOLLI~1\LOCALS~1\Temp\1\OraInstall2008-04-22_03-44-38PM"
The number of files bootstrapped for the jre is 528.
The number of files bootstrapped for the oui is 98.
what might be the problem, is this due to not having unzip software in the server.
Please help me

Just check this link:
Oracle Installer crashes in Windows XP attempting to install 10g database
May be useful...
Amardeep Sidhu
http://www.amardeepsidhu.com

Oracle 8 installation problem on windows 2003 server

Hi!everyone
while installing i'm getting the message "could not delete the windows nt services". The error is coming for the service "OracleTNSListener".
any solution?...
any info whether oracle 8 support has been stopped for all platforms/specific ones ?...where do i get that info ?....
plz help..

Hi!
Is there any work around to that? Basically I have to test an upgrade from 8i to 10g on a Windows Server 2003 w/ SP1. I am not sure on what platform that 8i database is running on because is at a third-party location.

Xp_logininfo Installation problem

Hello gurus,
I'm facing the same problem as described in this link:
Re: xp_logininfo "Installation problem on windows 2003 with Sql 2005"
the error I get is similiar:
The below message comes from executing the command master..xp_logininfo '<domain>\<user> ' Msg 15404, Level 16, State 11, Procedure xp_logininfo, Line 62 Could not obtain information about Windows NT group/user '<domain>\<user> ', error code 0x534. The statement has been terminated
but I just don't get how to solve it.
-I've tried to use the profiler but didn't find any information that will help me to solve.
-One of the guys wrote to add "logon rights" to the user ... what does it mean ?
Please advice,
Dimitry Haritonov

Hi sven,
Thank you very much for the quick and direct answer.
The problem was that the user that runs the SQL SERVER service didn't have authorization to retrieve information from active directory.
I've changed the service user, run the sapinst again, and after it succeeded I've returned the previous user.
Best regards,
Dimitry Haritonov

ERP 6 installation Problem on windows clustring

i am installing SAP ERP 6 EHP4 on windows 2003 with clustering 2 nodes only and DB as MS SQL 2005. i have Domain controller on one node and other is member of it , i want ACTIVE/ACTIVE clustering , so i installed MS SQL on one node and on other node i installed ASCS from SAP High Availability environment, and now i am configuring the first NODE on MSCS step ,here after accepting the password of the two domain user , it gives the problem:- ****************************
Number value 0x-3f580000 is bigger than 0xFFFFFFFF *******************************
the last lines of sapinst.log files are like this :- *******************************
INFO 2010-08-18 14:13:31.984
Execute step dAskForKernelDVD of component |MSCS_A|windows|ind|ind|ind|0|0|UserDialogs|windows |ind|ind|ind|2|0
INFO 2010-08-18 14:14:01.298
Execute step dAskForSecondKernelDVD of component |MSCS_A|windows|ind|ind|ind|0|0|UserDialogs|windows |ind|ind|ind|2|0
INFO 2010-08-18 14:14:01.314
Execute step dAskForuserDomain of component |MSCS_A|windows|ind|ind|ind|0|0|UserDialogs|windows |ind|ind|ind|2|0
INFO 2010-08-18 14:14:03.126
Execute step dBuildAccountInformation of component |MSCS_A|windows|ind|ind|ind|0|0|UserDialogs|windows |ind|ind|ind|2|0
INFO 2010-08-18 14:14:03.142
Execute step dAskForUserPAsswords of component |MSCS_A|windows|ind|ind|ind|0|0|UserDialogs|windows |ind|ind|ind|2|0
INFO 2010-08-18 14:14:32.143
Execute step dCollectMSCSNodesInformations of component |MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0
INFO 2010-08-18 14:14:32.174
Execute step dGetSAPClusterParameters of component |MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0
WARNING[E] 2010-08-18 14:14:32.174
MUT-03028 Number value 0x-3f580000 is bigger than 0xFFFFFFFF.
ERROR 2010-08-18 14:14:32.268
FCO-00011 The step dGetSAPClusterParameters with step key |MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0|dGetSAPClusterParameters was executed with status ERROR .
INFO 2010-08-18 14:14:44.237
An error occured and the user decided to retry the current step: "|MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0|dGetSAPClusterParameters" .
WARNING[E] 2010-08-18 14:14:44.253
MUT-03028 Number value 0x-3f580000 is bigger than 0xFFFFFFFF.
ERROR 2010-08-18 14:14:44.268
FCO-00011 The step dGetSAPClusterParameters with step key |MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0|dGetSAPClusterParameters was executed with status ERROR .
INFO 2010-08-18 14:14:44.878
An error occured and the user decided to retry the current step: "|MSCS_A|windows|ind|ind|ind|0|0|CollectClusterParam eters|windows|ind|ind|ind|3|0|dGetSAPClusterParameters" .
WARNING[E] 2010-08-18 14:14:44.893
MUT-03028 Number value 0x-3f580000 is bigger than 0xFFFFFFFF.
Help Me if you can thank you in advance

>> i am installing SAP ERP 6 EHP4 on windows 2003 with clustering 2 nodes only and DB as MS SQL 2005. i have Domain controller on one node and other is member of it
Installations on domain controllers are not supported:
Installation guide "2.2.4 Requirements for a High-Availability System":
<...>
You cannot use a host with a domain controller as an MSCS cluster node.
<...>
It's pretty clear why: If the first node, the domain controller, fails, the second node can't authenticate any more and hence the system won't start/run.
Markus

Installation problem on windows server 2008 r2 datacenter edition 64bit

hi
today, i tried to install the current maxdb 7.8 release on my virtual server with a windows server 2008 r2 datacenter 64bit edition os. at the first installation, i got an error message something with "rte runtime error". at this point, the installation stopped.
because of this error, i tried to uninstall the failed installation. this was not possible, in the uninstaller, i didn't see any components, so i can't uninstall.
so i tried to delete the files manually: the entries in the start menu, and the application's path under "program files"... first, i need to kill a process named "serv.exe", that creates a tcp daemon under port 7200... after killing it, the deletion of the dir in program files was successful.
this is very very weird, now my server is "contaminated" with an uncomplete uninstallation of maxdb...
why maxdb 7.8 has problems on windows server 2008 r2 datacenter 64bit edition???
thanks for feedbacks!
regards, jan

> no, because i canceled this virtual server - another method to solve this problem. (i have really no time for things like that..!)
If you take the time to give exact error messages then someone will be certainly able to help
> on windows server 2003, there are NO problems.
Windows 2003 != Windows 2008 - they use a different kernel, a different security system (UAC) and other features that may prevent a succesfull installation in the first place.
I installed a MaxDB 7.8 just today on Windows 2008 R2 and it worked fine.
Markus

Oracle database 11g release 2 installation problem on windows 7 (64-bit)

First of all my windows is not genuine, but on my friend's desktop oracle download and installation worked fine, he chose "create and configure database" options, and it works very well on his desktop, though his windows is also illegitimate. In my case, when I select "Create and configure database" option and pressed 'next",
(Go to my blog to see it with snapshots: Computer Science: Oracle database 11g release 2 installation problem on windows 7 (64-bit))
it asks to select class, I select "Desktop class" and pressed "next". The moment I pressed "next", the whole setup thing disappeared like it was never started. I searched for all possible reasons for why its not getting installed on my laptop, I used registry cleaner s/w, deleted 25 GB of data to create free space if it were the problem, increased the virtual memory to increase the space for RAM, I did almost everything to get this setup working, but I found no success with the "Create and Configure database" option
and
then
I chose a "database software only" option and chose to store in a folder w/o spaces. This way, I got database s/w only and then later I found "Database configuration Assistant (DBCA)" from windows START button and clicked to create and configure database manually. The steps are pretty much interactive and doesn't involve much brainstorming.
The values I filled for
1) Global Database Name : orcl
2) System Identifier : orcl
3) I chose common password for both SYS and SYSTEM
4) while on Enterprise Manager Configuration step, It asked me to create and configure listener in oracle home, so for that too, I typed "netca" in windows START menu and clicked it. There I added a listener.
5) I chose a Storage area which was the Oracle-home itself i.e. where our installation files goes , in my case it is : C:\oracle_base\product\11.2.0\dbhome_1\oradata
6) Then after few more nitty-gritty clicks, we are set to go !
Finally to write SQL code and to create your first TABLE , type "sqlplus" in windows "START" menu and click it when it appears. A command-prompt like window appears , which will ask you for username and password, so here they are :
Username : sys/ as sysdba
Password : (its the one you created in step 3 stated above )
After this you are ready to write your first SQL command.

Is this your solution to your original post at Oracle database 11g release 2 installation on windows 7 (64-bit) ?
Pl be aware that you should not create any custom objects in SYS or SYSTEM schema - you should create any such objects in a separate custom schema.
About Database Administrator Security and Privileges

How to make column headers in table in PDF report appear bold while datas in table appear regular from c# windows forms with sql server2008 using iTextSharp

Hi my name is vishal
For past 10 days i have been breaking my head on how to make column headers in table appear bold while datas in table appear regular from c# windows forms with sql server2008 using iTextSharp.
Given below is my code in c# on how i export datas from different tables in sql server to PDF report using iTextSharp:
using System;
using System.Collections.Generic;
using System.ComponentModel;
using System.Data;
using System.Drawing;
using System.Linq;
using System.Text;
using System.Threading.Tasks;
using System.Windows.Forms;
using System.Data.SqlClient;
using iTextSharp.text;
using iTextSharp.text.pdf;
using System.Diagnostics;
using System.IO;
namespace DRRS_CSharp
public partial class frmPDF : Form
public frmPDF()
InitializeComponent();
private void button1_Click(object sender, EventArgs e)
Document doc = new Document(PageSize.A4.Rotate());
var writer = PdfWriter.GetInstance(doc, new FileStream("AssignedDialyzer.pdf", FileMode.Create));
doc.SetMargins(50, 50, 50, 50);
doc.SetPageSize(new iTextSharp.text.Rectangle(iTextSharp.text.PageSize.LETTER.Width, iTextSharp.text.PageSize.LETTER.Height));
doc.Open();
PdfPTable table = new PdfPTable(6);
table.TotalWidth =530f;
table.LockedWidth = true;
PdfPCell cell = new PdfPCell(new Phrase("Institute/Hospital:AIIMS,NEW DELHI", FontFactory.GetFont("Arial", 14, iTextSharp.text.Font.BOLD, BaseColor.BLACK)));
cell.Colspan = 6;
cell.HorizontalAlignment = 0;
table.AddCell(cell);
Paragraph para=new Paragraph("DCS Clinical Record-Assigned Dialyzer",FontFactory.GetFont("Arial",16,iTextSharp.text.Font.BOLD,BaseColor.BLACK));
para.Alignment = Element.ALIGN_CENTER;
iTextSharp.text.Image png = iTextSharp.text.Image.GetInstance("logo5.png");
png.ScaleToFit(105f, 105f);
png.Alignment = Element.ALIGN_RIGHT;
SqlConnection conn = new SqlConnection("Data Source=NPD-4\\SQLEXPRESS;Initial Catalog=DRRS;Integrated Security=true");
SqlCommand cmd = new SqlCommand("Select d.dialyserID,r.errorCode,r.dialysis_date,pn.patient_first_name,pn.patient_last_name,d.manufacturer,d.dialyzer_size,r.start_date,r.end_date,d.packed_volume,r.bundle_vol,r.disinfectant,t.Technician_first_name,t.Technician_last_name from dialyser d,patient_name pn,reprocessor r,Techniciandetail t where pn.patient_id=d.patient_id and r.dialyzer_id=d.dialyserID and t.technician_id=r.technician_id and d.deleted_status=0 and d.closed_status=0 and pn.status=1 and r.errorCode<106 and r.reprocessor_id in (Select max(reprocessor_id) from reprocessor where dialyzer_id=d.dialyserID) order by pn.patient_first_name,pn.patient_last_name", conn);
conn.Open();
SqlDataReader dr;
dr = cmd.ExecuteReader();
table.AddCell("Reprocessing Date");
table.AddCell("Patient Name");
table.AddCell("Dialyzer(Manufacturer,Size)");
table.AddCell("No.of Reuse");
table.AddCell("Verification");
table.AddCell("DialyzerID");
while (dr.Read())
table.AddCell(dr[2].ToString());
table.AddCell(dr[3].ToString() +"_"+ dr[4].ToString());
table.AddCell(dr[5].ToString() + "-" + dr[6].ToString());
table.AddCell("@count".ToString());
table.AddCell(dr[12].ToString() + "-" + dr[13].ToString());
table.AddCell(dr[0].ToString());
dr.Close();
table.SpacingBefore = 15f;
doc.Add(para);
doc.Add(png);
doc.Add(table);
doc.Close();
System.Diagnostics.Process.Start("AssignedDialyzer.pdf");
if (MessageBox.Show("Do you want to save changes to AssignedDialyzer.pdf before closing?", "DRRS", MessageBoxButtons.YesNoCancel, MessageBoxIcon.Exclamation) == DialogResult.Yes)
var writer2 = PdfWriter.GetInstance(doc, new FileStream("AssignedDialyzer.pdf", FileMode.Create));
else if (MessageBox.Show("Do you want to save changes to AssignedDialyzer.pdf before closing?", "DRRS", MessageBoxButtons.YesNoCancel, MessageBoxIcon.Exclamation) == DialogResult.No)
this.Close();
The above code executes well with no problem at all!
As you can see the file to which i create and save and open my pdf report is
AssignedDialyzer.pdf.
The column headers of table in pdf report from c# windows forms using iTextSharp are
"Reprocessing Date","Patient Name","Dialyzer(Manufacturer,Size)","No.of Reuse","Verification" and
"DialyzerID".
However the problem i am facing is after execution and opening of document is my
column headers in table in pdf report from
c# and datas in it all appear in bold.
I have browsed through net regarding to solve this problem but with no success.
What i want is my pdf report from c# should be similar to following format which i was able to accomplish in vb6,adodb with MS access using iTextSharp.:
Given below is report which i have achieved from vb6,adodb with MS access using iTextSharp
I know that there has to be another way to solve my problem.I have browsed many articles in net regarding exporting sql datas to above format but with no success!
Is there is any another way to solve to my problem on exporting sql datas from c# windows forms using iTextSharp to above format given in the picture/image above?!
If so Then Can anyone tell me what modifications must i do in my c# code given above so that my pdf report from c# windows forms using iTextSharp will look similar to image/picture(pdf report) which i was able to accomplish from
vb6,adodb with ms access using iTextSharp?
I have approached Sound Forge.Net for help but with no success.
I hope anyone/someone truly understands what i am trying to ask!
I know i have to do lot of modifications in my c# code to achieve this level of perfection but i dont know how to do it.
Can anyone help me please! Any help/guidance in solving this problem would be greatly appreciated.
I hope i get a reply in terms of solving this problem.
vishal

Hi,
About iTextSharp component issue , I think this case is off-topic in here.
I suggest you consulting to compenent provider.
http://sourceforge.net/projects/itextsharp/
Regards,
Marvin
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Lightroom 3.2 Installation Problem on Windows 7 64-bit

Lightroom 3.2 Installation Problem on Windows 7 64-bit
I can't install Lightroom 3.2 (German) on my computer (Windows 7 Professional 64-bit).
While copying the extracted program files the following error message appears:
An error occurred during the installation of assembly component {6435B7C0-E0C8-3EA2-91AE-7640034EAFCE}. HRESULT: 0x80070002.
I found out that other users had the same problem, and couldn't find a solution.
Perhaps it is a Microsoft .NET Framework related problem. But after installing .NET Framework 4 nothing changed.
Thanks for ideas to solve the problem.

Thanks for your advice, Mr. McLion.
I downloaded the 3.4.1 version and started the installation as administrator. Unfortunately the same error message occured again.
Then I tried to install the 32-bit version (although I prefer a 64-bit program on a 64-bit operating system). A similar error message appeared at the same point of installation progress, but with another combination of numbers and letters in brackets.

ORADC problem on Windows 2000 with Service pack 1 and service pack 2

Hi,
I have a VB application running on NT4.0 workstations. It uses
ORADC control to talk to ORACLE 7.3 When I load it on Windows
2000 with service pack 1 or service pack 2, I encounter some
problems.
The ORADC control is used in most of the VB forms and the
Refresh method of the ORADC conrol is used to refresh the APEX
TRUE DBGRID PRO control. When this action is executed, I receive
a run time error
"Method Refresh of object '_DORADC' failed Err#: -2147417848
It works fine when no service pack is applied on Win2K.
Can anyone tell me what's going on?
Thanks

satheesh_p wrote:
Thanks for your reply.
When I checked the system requirements. I couldn't find information on windows 2003 service pack 2
link http://www.adobe.com/products/coldfusion/systemreqs/.
Whether your OS is windows 2003 with service pack 2?
Are you sure coldfusion 8 will work on windows 2003 with service pack 2?
Regards,
Satheesh.
Well it was there, if you understand the naming properly:
ColdFusion 8 system requirements
Windows
Intel® Pentium® II or AMD Athlon processor
Microsoft®
Windows® 2000 Professional with Service Pack 3; Windows 2000 Server,
Advanced Server, or Datacenter Server with Service Pack 3; Windows
Server® 2003 Web, Standard, or Enterprise Edition with Service Pack 1
and R2; Windows Server® 2008; Windows XP Professional or Home Edition;
or Windows Vista®
R2 is the "offical" Microsoft name for service pack 2.

NTLM is not working with EP 6 SP 9 on Windows 2003 with IIS 6.

I installed EP 6 SP 9 on windiows 2003 server with IIS version 6.
Configures IisProxy.xml for redirection for filter irj. When I make a call to default website, it in turn calls server with irj filter.
Portal page comes up and requesting me to enter user id password.
I made the changes mentioned by some of the web logs in this site.
I configured HeaderVariableLoginModule an and added as explined by Gregory Wolf on the following topic.
Integrated Windows Authentication with SAP EP 6.0 SP 3 and higher.
I see following log from Ep 6 SP 9 log file security.log from directory E:\usr\sap\DEV\JC00\j2ee\cluster\server0\log\system.
security#Plain###No user name provided.#
#1.5#000C2953326B00430000000100000A780003F358EF2132DE#1111988099323#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####200d0cb09f4b11d9926a000c2953326b#SAPEngine_Application_Thread[impl:3]_37##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
#1.5#000C2953326B00440000000000000A780003F3591D22E168#1111988846027#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####dd1f09b19f4c11d98e98000c2953326b#SAPEngine_Application_Thread[impl:3]_7##0#0#Info#1#com.sap.engine.services.security#Plain###No user name provided.#
#1.5#000C2953326B00440000000100000A780003F3591D22E215#1111988846027#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####dd1f09b19f4c11d98e98000c2953326b#SAPEngine_Application_Thread[impl:3]_7##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
#1.5#000C2953326B00450000000000000A780003F359227DE92E#1111988935662#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####128c40e09f4d11d9acb7000c2953326b#SAPEngine_Application_Thread[impl:3]_28##0#0#Info#1#com.sap.engine.services.security#Plain###No user name provided.#
#1.5#000C2953326B00450000000100000A780003F359227DEDC7#1111988935662#/System/Security#sap.com/irj#com.sap.engine.services.security#Guest#18####128c40e09f4d11d9acb7000c2953326b#SAPEngine_Application_Thread[impl:3]_28##0#0#Info#1#com.sap.engine.services.security#Plain###Cannot log info about the logon attempt because the user name is null.#
Lots of weblogs are pointing to remote_user value in IisProxy.log file. I am not able to see that.
I also tried switching IIS 6 to run as IIS 5 and did not help much at all.
Please help me on the issue.
I did not change authschemes.xml file.
My IisProxy.xml file looks as follows:
<?xml version="1.0" encoding="utf-8" ?>
<!DOCTYPE ISAPI-config[
 <!ELEMENT ISAPI-config ( filter, extension, ( mapping | config )* )>
 <!ATTLIST ISAPI-config
 version CDATA #REQUIRED
 >
 <!ELEMENT filter (log-path?)>
 <!ATTLIST filter
 name CDATA #IMPLIED
 log-level CDATA "3"
 log-flags CDATA "0x00000001"
 debug-flags CDATA "0x00008000"
 priority ( high | medium | low ) "high"
 extension-url CDATA "/scripts/IisProxy.dll"
 authentication ( skip | normal | forward ) "normal"
 remote-address ( skip | forward ) "skip"
 >
 <!ELEMENT extension (
 keystore-dir?,
 log-path?,
 data-path?,
 trace-path? )>
 <!ATTLIST extension
 name CDATA #IMPLIED
 log-level CDATA "1"
 log-flags CDATA "0"
 debug-flags CDATA "0"
 access ( filter | direct | both ) "filter"
 >
 <!ELEMENT keystore-dir (#PCDATA)>
 <!ELEMENT log-path (#PCDATA)>
 <!ELEMENT data-path (#PCDATA)>
 <!ELEMENT trace-path (#PCDATA)>
 <!ELEMENT mapping (
 source+,
 target,
 compress-types*,
 protocol-header?,
 certificate-header?,
 cert-chain-header?,
 cipher-header?,
 keysize-header?,
 keystore-path?,
 log-path?,
 data-path? )>
 <!ATTLIST mapping
 name CDATA #IMPLIED
 log-level CDATA "1"
 log-flags CDATA "0"
 debug-flags CDATA "0"
 keep-alive ( true | false ) "true"
 use-continue ( true | false ) "true"
 close-socket ( true | false ) "true"
 close-socket-delay CDATA "1000"
 thread-count CDATA "100"
 max-socket-age CDATA "37"
 >
 <!ELEMENT source (protocol, host?, port?, prefix, new-prefix?)>
 <!ATTLIST source
 access ( filter | direct | both ) "filter"
 >
 <!ELEMENT protocol (#PCDATA)>
 <!ELEMENT host (#PCDATA)>
 <!ELEMENT port (#PCDATA)>
 <!ELEMENT prefix (#PCDATA)>
 <!ELEMENT new-prefix (#PCDATA)>
 <!ELEMENT target (protocol, host, port)>
 <!ELEMENT compress-types (#PCDATA)>
 <!ATTLIST compress-types
 min-size CDATA "1024"
 >
 <!ELEMENT protocol-header (#PCDATA)>
 <!ELEMENT certificate-header (#PCDATA)>
 <!ELEMENT cert-chain-header (#PCDATA)>
 <!ELEMENT cipher-header (#PCDATA)>
 <!ELEMENT keysize-header (#PCDATA)>
 <!ELEMENT keystore-path (#PCDATA)>
 <!ELEMENT config ( source+ )>
]>
<ISAPI-config version="1.6">
 <filter name="IisProxy filter"/>
 <extension name="IisProxy extension" />
 <mapping name="IisProxy samples">
 <source>
 <protocol>http</protocol>
 <prefix>/irj</prefix>
 </source>
 <source>
 <protocol>http</protocol>
 <prefix>/Hello/</prefix>
 </source>
 <source>
 <protocol>http</protocol>
 <prefix>/Hello2/</prefix>
 <new-prefix>/Hello/</new-prefix>
 </source>
 <target>
 <protocol>http</protocol>
 <host>slcsepw04vd.pacificorp.us</host>
 <port>50000</port>
 </target>
 <compress-types>text/html, text/plain</compress-types>
 </mapping>
 <mapping name="Secure IisProxy samples">
 <source>
 <protocol>https</protocol>
 <prefix>/Hello/</prefix>
 </source>
 <target>
 <protocol>https</protocol>
 <host>localhost.your.corp</host>
 <port>8443</port>
 </target>
 <keystore-path>c:\sec\SAPSSLC.pse</keystore-path>
 </mapping>
 <config>
 <source>
 <protocol>http</protocol>
 <host>localhost</host>
 <prefix>/IisProxy</prefix>
 </source>
 <source>
 <protocol>https</protocol>
 <host>localhost</host>
 <prefix>/IisProxy</prefix>
 </source>
 </config>
</ISAPI-config>
Please help me. I am not sure what is missing. Please make a note that Portal version is EP 6 SP9 & Server is Windows 2003 with IIS 6.

I made the change as you requested and it did not help.
I do not see any remote_user entry in IisProxy.log file.
Please let me know the procedure to get REMOTE_USER into the IisProxy.log file.
<?xml version="1.0" encoding="utf-8" ?>
<!DOCTYPE ISAPI-config[
 <!ELEMENT ISAPI-config ( filter, extension, ( mapping | config )* )>
 <!ATTLIST ISAPI-config
 version CDATA #REQUIRED
 >
 <!ELEMENT filter (log-path?)>
 <!ATTLIST filter
 name CDATA #IMPLIED
 log-level CDATA "3"
 log-flags CDATA "0x00000001"
 debug-flags CDATA "0x00008000"
 priority ( high | medium | low ) "high"
 extension-url CDATA "/scripts/IisProxy.dll"
 authentication ( skip | normal | forward ) "normal"
 remote-address ( skip | forward ) "skip"
 >
 <!ELEMENT extension (
 keystore-dir?,
 log-path?,
 data-path?,
 trace-path? )>
 <!ATTLIST extension
 name CDATA #IMPLIED
 log-level CDATA "1"
 log-flags CDATA "0"
 debug-flags CDATA "0"
 access ( filter | direct | both ) "filter"
 >
 <!ELEMENT keystore-dir (#PCDATA)>
 <!ELEMENT log-path (#PCDATA)>
 <!ELEMENT data-path (#PCDATA)>
 <!ELEMENT trace-path (#PCDATA)>
 <!ELEMENT mapping (
 source+,
 target,
 compress-types*,
 protocol-header?,
 certificate-header?,
 cert-chain-header?,
 cipher-header?,
 keysize-header?,
 keystore-path?,
 log-path?,
 data-path? )>
 <!ATTLIST mapping
 name CDATA #IMPLIED
 log-level CDATA "1"
 log-flags CDATA "0"
 debug-flags CDATA "0"
 keep-alive ( true | false ) "true"
 use-continue ( true | false ) "true"
 close-socket ( true | false ) "true"
 close-socket-delay CDATA "1000"
 thread-count CDATA "100"
 max-socket-age CDATA "37"
 >
 <!ELEMENT source (protocol, host?, port?, prefix, new-prefix?)>
 <!ATTLIST source
 access ( filter | direct | both ) "filter"
 >
 <!ELEMENT protocol (#PCDATA)>
 <!ELEMENT host (#PCDATA)>
 <!ELEMENT port (#PCDATA)>
 <!ELEMENT prefix (#PCDATA)>
 <!ELEMENT new-prefix (#PCDATA)>
 <!ELEMENT target (protocol, host, port)>
 <!ELEMENT compress-types (#PCDATA)>
 <!ATTLIST compress-types
 min-size CDATA "1024"
 >
 <!ELEMENT protocol-header (#PCDATA)>
 <!ELEMENT certificate-header (#PCDATA)>
 <!ELEMENT cert-chain-header (#PCDATA)>
 <!ELEMENT cipher-header (#PCDATA)>
 <!ELEMENT keysize-header (#PCDATA)>
 <!ELEMENT keystore-path (#PCDATA)>
 <!ELEMENT config ( source+ )>
]>
<ISAPI-config version="1.6">
 <filter name="IisProxy filter" authentication="forward"/>
 <extension name="IisProxy extension" />
 <mapping name="IisProxy samples">
 <source>
 <protocol>http</protocol>
 <prefix>/irj</prefix>
 </source>
 <source>
 <protocol>http</protocol>
 <prefix>/Hello/</prefix>
 </source>
 <source>
 <protocol>http</protocol>
 <prefix>/Hello2/</prefix>
 <new-prefix>/Hello/</new-prefix>
 </source>
 <target>
 <protocol>http</protocol>
 <host>slcsepw04vd.pacificorp.us</host>
 <port>50000</port>
 </target>
 <compress-types>text/html, text/plain</compress-types>
 </mapping>
 <mapping name="Secure IisProxy samples">
 <source>
 <protocol>https</protocol>
 <prefix>/Hello/</prefix>
 </source>
 <target>
 <protocol>https</protocol>
 <host>localhost.your.corp</host>
 <port>8443</port>
 </target>
 <keystore-path>c:secSAPSSLC.pse</keystore-path>
 </mapping>
 <config>
 <source>
 <protocol>http</protocol>
 <host>localhost</host>
 <prefix>/IisProxy</prefix>
 </source>
 <source>
 <protocol>https</protocol>
 <host>localhost</host>
 <prefix>/IisProxy</prefix>
 </source>
 </config>
</ISAPI-config>
Please let me know what is missing.
Thanks.

Xp_logininfo "Installation problem on windows 2003 with Sql 2005"

Similar Messages

Maybe you are looking for