XP Machine hangs when plugging in PCMCIA-FBUS

I have a PCMCIA-FBUS card that I have been using in another machine and it works. I have installed NI-FBUS Communication manager and Configurator on a machine running Windows XP. When I insert the PCMCIA card, the machine just hang - I cannot move the mouse. If I shutdown the machine and insert it while it's off and then power on the machine, the machine hangs at the XP Operating system splash screen. Should I be able to use the Fieldbus PCMCIA card with a laptop running XP?
PS - The laptop is a Dell Latitude D600.
Dawn
Software Engineer
Micro Motion, Inc
[email protected]

Looks like you may have the series ONE card that causes a problem with some new laptops.
There is a whole bunch of info on previous threads about this issue.
The solution is to get another laptop with a different PCMCIA controller chip or buy the new series TWO card.
The link below should get you to that thread.
http://forums.ni.com/ni/board/message?board.id=120&message.id=81
Regards,
Allen
FF-EUC Aus

Similar Messages

How do I fix firefox, which hangs when plug in container starts?

Firefox hangs or freezes & I can't click on anything when plug in container shows up (see it in task manager).

There are some compatibility issues between the latest Flash player and some Firefox add-ons or settings. Flash 11.3.300.257, in particular, can cause crashes. Please check out these articles:
* [[Flash 11.3 crashes]]
* [[Flash 11.3 doesn't load video in Firefox]]

Internet hangs when plugged in

I've had my MacBook for a couple of months and I'm getting very frustrated. In the beginning, I could be surfing the net with no problem, and then the machine would just stop loading pages. I called tech support and went through all the normal things. After a few weeks, it got worse, to the point where the computer would state "You must restart your computer" over and over. I sent it in for repair and they replaced the hard drive. When I got it back, I got the same restart message. Tonight I was surfing all over with no problem for the first time until I plugged the battery charger in because battery was getting low. As soon as I plugged it in, it wouldn't load a page....after I unplugged it, back to normal. Does anyone know what would cause this? I'm really going crazy here. Thanks.

i have the exact same issue. it annoys me to no end. i really hope they fix this issue with an update soon.

Arch hangs when plugging usb devices

hi.i'm using arch x86_64 with gnome 3.
when i plug an usb device to my laptop arch hangs and all of devices stop working ( mouse keyboard ...).
i already had this problem and i had fixed it by -Syu.but this time it does not fix.
i'm using kernel 2.6.39 (latest)
in gdm (before logging in to gnome 3 enviroment) plugging usb devices does not occure this problem.
this problem usually happen when i install reinstall or update a package with pacman.
please help to fix this problem!

ok.i discovered the problem.i was using asus-switcheroo for turning off my discrete graphic card (nvidia Optimus which dows not work on linux) and when i disabled asus-switcheroo this problem solved.
but what can i do about turning off discrete graphic?
in this situation i can't use that graphic card but it uses power.

OS X Yosemite hangs when exiting Time Machine Interface

Hi all,
Under special circumstances, OS X hangs when we exit the Time Machine interface. This seems to be related to the "Login Window".
Let's me explain the steps to reproduce the bug :
1. Boot normally and log into your session (with password).
2. Then, enter the Time Machine interface and do some browsing (or not).
3. Exit Time Machine interface by clicking the "Cancel" button.
For this first time, all is working as expected, no hang.
4. Now, go to the "Login Window" (with the method shown on the image below) . IMPORTANT: Do not close your session, only switch to the "Login Window" by keeping your active session in background.
5. Relog into your session normally by entering your password.
6. Then, reenter the Time Machine interface and do some browsing (or not).
7. Exit Time Machine interface again by clicking the "Cancel" button.
This time, the mac is supposed to freeze and not come back to life (Beach Ball of Death)...
Can you replicate this on your Mac, just to see if I'm not alone ??!!
Thanks,
Torp

EDIT:
In the meantime, you can workaround this bug (without force shutdown your Mac) by assigning a keyboard shortcut to call the "Login Window". I use "Lock Me Now" (http://www.igrsoft.com/en/lockmenow/) to do this. So, next time your OS X hangs, all you have to do is to call the "Login Window" with your keyboard shortcut and relog to your session and the "spinning beach ball" should go away !

My macbook pro mid 2009 OSX Lion 10.7.4 randomly Hanging when backing up with Time Machine

My macbook pro mid 2009 OSX Lion 10.7.4 randomly Hanging when backing up with Time Machine to Time Capsule. Anyone else have this issue?

bumping this up. Same issues persist even with 10.7.5

Hard drive works, but when plugged in hangs the system

First of all, since this is not a Linux-specific problem I'm not sure this is the right place for this post.
Anyway, for the past few years I've been using a 250GB IDE hard drive mostly to store backups on. For quite a while it worked fine, but when plugged in again after being removed so I could clean out the dust in my PC it didn't work quite right anymore. It caused the system to hang and gave error messages remniscent of those detailed on this page. After some fiddling it worked OK for a while, and then one day it randomly did this again. I took the ribbon cable out, then the hard drive, and realized one of the pins was pushed in (at the time I thought it was broken). After some reading I decided to sacrifice a ribbon cable. What I did was yank a pin off of an old DVD drive that doesn't work and shoved it in the cable where the short pin was. I made sure it was seated well, plugged in in, and hoped for the best. To my delight it worked without a hitch for maybe a year or more.
And then a little more than a month ago we had lightning strike a power line outside of our house and it fried my motherboard. I now have a replacement board, but after all of the taking apart and moving around and stuff, the hard drive is back to its old antics. The pin-in-the-cable trick wasn't working anymore. After I realized that the pin wasn't broken half-way but rather pushed in, I grabbed some needlenose pliers and pulled it out. It now will plug into any ribbon cable just fine and the computer recognizes it, but it's slow at POST and hangs the system when booting the OS, whether it be Linux or Windows. Knoppix CDs boot just fine, although slower. S.M.A.R.T. sees no problems.
Basically I'm wondering 2 things. First of all, is there anything I can do to get around the hangs? And second, I'm considering buying an external hard drive enclosure for regular 3.5 inch hard drives and using it as an external USB drive. Since the drive does still work and I can add/remove stuff while booted in Knoppix, and the main issue seems to be my system hanging, I figure, maybe, I can just plug in the drive when I need it after the computer is already booted up and it will work fine. Does this sound like a reasonable expectation?

What you hear may sound like it's the hard drive, but it's really an electronic type of noise. Same with my PB. Try what BGreg said, and wait for the drive to spin down - you'll still hear the noise.
There was a thread about this issue several months ago, and IIRC the conclusion was that it's a normal noise, and that you should just ignore it if possible.
If you must make it quieter, set processor performance to the lowest setting in Energy Saver preferences. But it's not going away completely.

T400 (running Vista) hangs when not plugged in

My Lenovo T400 often hangs when running on the battery but never when it's plugged in. I'm using Windows Vista.

what happens when you press Ctrl + Alt + Del when it hangs?
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

I currently have the iphone using imei is 013428003820386. I'm using normal. When I plug the phone into the laptop to copy the photos to your computer system requires update to the latest version. I agree to the machine but when the update requires activa

I currently have the iphone using imei is 013428003820386. I'm using normal. When I plug the phone into the laptop to copy the photos to your computer system requires update to the latest version. I agree to the machine but when the update requires activation by icloud account. I logged in with my account but still not activated and security. My account is being used to send mail me this log. I respectfully request that you can help me to reactivate my phone. Thank you very much. I swear this is my phone and I have been using previously. Thank you, thank you

Don't post personal details on a public user to user technical support forum where nobody can help you.
If you want help, then contact Apple directly, but not here on a public user forum.

What is the proper way to fix the Flash Plug-in issue that causes Firefox to hang when playing Flash videos

This is annoying and causing me to set my default to Chrome. Firefox hangs when playing Flash. I have tirelessly tried everything I could. Uninstalling Flash via the Adobe download. Uninstalling FF and every single one of it's folders. I've done it all, multiple times....and continue to have the exact same problem, any Flash video hangs. Please help, I have read countless articles about others having this same problem, yet nobody offers a real solution.
== URL of affected sites ==
http://www.youtube.com

This is annoying and causing me to set my default to Chrome. Firefox hangs when playing Flash. I have tirelessly tried everything I could. Uninstalling Flash via the Adobe download. Uninstalling FF and every single one of it's folders. I've done it all, multiple times....and continue to have the exact same problem, any Flash video hangs. Please help, I have read countless articles about others having this same problem, yet nobody offers a real solution.
== URL of affected sites ==
http://www.youtube.com

IE7 hangs when closing tab

I have an applet which has been functioning fine, but with the introduction of IE7 and tabs, I suddenly have an issue. We run a web site for our users, through which, they view PDF files. Simply, users view PDF files through a web browser (with the AcrobatReader plug-in), which are displayed via 'getAppletContext.showDocument(URL, "_blank")'. This is a fairly small user community, and we require that AcrobatReader is present on their machines. As I mentioned, this has been working fine with no issues until IE7. Now that users can configure their web browsers to open all pop-ups in a tab, rather than a new browser instance, we have constant reports of the browser 'hanging' when they try to close the tab containing the PDF viewer. Again, there is no issue if their browser is configured to open a new browser instance. Any ideas?

DrClap wrote:
It's been a while since this happened, but I had a problem where Acrobat wouldn't start up, it would just hang with a blank screen. When I went and cleared out the temp directories that problem went away.The acrobat plugin has been broken for many, many, many years. Possibly forever.
It's not uncommon to launch IE. Open PDFs through IE. Close IE. Find one or even multiple orphaned acrobat processes running. When you get enough of these they will crash acrobat if you attempt to open new ones.

Premiere Elements 11 hangs when opening projects

I have a 64 bit HP ProBook 4740s with Premiere Elements 11 installed. I use my laptop 2 days a week and work from a desktop machine 3 days a week.
The laptop installation of PE11 hangs when I try to open projects but when plugging external hard drive into desktop the project opens fine.
All files are on the hard drive so it's not from missing files.
If I create a new project PE11 runs fine I then create another new project and it hangs
Really frustrated, even reinstalled - still same issues.

Martin-Evans1
We were pleased to learn that your problem was resolved by a just the Premiere Elements uninstall/reinstall
as you wrote in your post 2 and repeated your result in post 4.
As SG pointed out, the details of these issues are important to get at the core of the issues (whys) and expedite
matters to get you moving forward with your projects.
If the problem reoccurs, please get back to SG in this thread with details necessary to help you. In this instance we will not know if the problem was really with the install or rather with corruption of Premiere Elements settings file which could have been handled by deleting the Adobe Premiere Elements Prefs file or the whole folder in which it exists on the hard drive.
Continued success.
Thanks.
ATR

Laptop unable to startup when plugged in

Hi, I have a laptop operating on Vista that won't startup properly when plugged in to power but will start up when operating on batteries. Once the computer has booted up and windows completes its startup I can plug it in and there doesn't seem to be any other problems but it is very annoying. Has anyone experienced this before?

No replies- can I be a bit more specific- When I say it doesn't start up properly, I mean that it hangs on the bios start screen and won't go any further. Then I have to close down, wait for the battery to charge, start up again and let "windows" go through the diagnostic crap for 10 minutes then restart it again only on batteries. After the machine has started, ...completely loading "windows" I can plug in the power cord and operate normally. Any ideas??

Itunes hangs when determining gapless playback

I have just plugged my portable hard drive back into my laptop after a month, i have 15,997 songs in total (60.93 GB)on my hard drive but it now hangs whilst doing the initial analyzing - on 378 of 4518 track 03 and will not progress. I have the latest itunes & ipod software installed, and have done this on numerous occasions with no problem having had an ipod for 3 years and always stored my music files in a portable hard drive to prevent music loss if my laptop crashed. Please help me resolve this problem
thanks

I have the same problem but with grievous outcome: my entire machine hangs; I've done EVERYTHING I, and several product specialists can think of short of deleting my entire music collection.
I don't think it has anything to do with the name of a single track - it's hanging on different tracks for me with no consistency in naming styles. I've reinstalled iTunes several times, killed the cache, the preferences, tried it as a different user, deleted and rebuilt my library, and NOTHING helps. When iTunes comes up, it immediately goes into "Determining Gapless Playback..." and withing 2-3 songs the machine HANGS and has to be hard powered.
Of course, I've tried to set every song to a non-gapless song, tried to turn on or off song crossfade, no luck.
APPLE: Please listen and help!! Make gapless playback a removable option or something!

Time Capsule and Time machine hangs my mac

I read through the first 20 pages to see if anybody else was having similar issues but then gave up so apologies if this is repeated.
OK here goes. I bought a TC 1 TB plugged it in, worked no problem and did so for ages. None of the problems mentioned by other people.
Recently I had a backup fail. At the time I had installed time machine editor some time previously and set it to back up once a day which it had been doing with no issues for weeks.
Reading the help topics I re-selected the TC in TM and off it went preparing - backup failed. Restarted both Mac and TC and tried again. This time it started the backup got to about 70GB and hung my mac - nothing worked had to hold the power button on the mac to get it to restart.
Plugged my mac directly into the TC to get a GB connection. Deleted the TC drive and reselected it. 70 (ish) GB failed and hung my machine. Checked the logs found the same file failing, excluded it from backups, deleted the drive started again - 70 ish GB failed again hung machine.
Rand apple support, was asked to do a few things. First hard reset the TC, second check permissions and repair on the mac hard drive. Third re-index the mac HD - then delete the TC drive and start again. 70 GB mac hung - warning server disconnect - backup failed.
Restarted TC and Mac, deleted TC drive, start again, 70 GB fail.
Now, the only thing that is going through my mind and im reaching here a bit is that about the time I started having problems was the same time I bought the new expansion to a game - World of Warcraft. I do play this daily and have been during the backups, I have been keeping an eye on the backups while playing and although they do appear to stop incrementing the machine is fine until I try to exit WoW. When I do the machine hangs (only does this when TM is running).
I am running out of ideas now, seem to have tried everything backups constantly failing at around the 70GB mark no more files needing to be excluded, the errors seem to be losing connection to TC server.

I ended up with a few days of talking to Apple support about this and here is how it went and this is what we tried.
Managed to get the TM to backup a full backup. The next backup failed and after that could not mount the bundle.
Deleted the drive started again, hung around 80% - same problem.
Deleted and renamed the drive - this seemed to work and full backup completed. Next backup failed.
Removed all of the 'offending' items from backup - i.e. pretty much anything that had ever been mentioned in a support forum, e.g. parallels drives, Aperture loads of stuff - no difference.
Complete reset on old time capsule - held reset button for 20 seconds while plugging power in. Deleted and renamed the old drive. Re-installed the firmware.
I excluded almost everything on the mac hard drive to make for a quick backup. It backed up fine but failed on next backup at which point the sparse bundle could no longer be mounted.
Apple still thought the problem was not the TC but something it was trying to backup.
Re-installed OSX. Removed everything from backup - i.e. excluded everything so it had nothing to backup. Then gave it 1 file to backup.
Backed up fine then failed at next backup.
Apple sent me a new replacement TC - removed everything (except parallels drive) from exclusions - plugged it in selected it as destination has been working fine ever since.
Now, Apple sent me the replacement with a not saying do not return old faulty equipment. So I got a new shiny replacement and my problem is solved.... however I am a curious sort and cannot figure out what is wrong with the old one. Its network is fine, I can use the drive as an external drive no problem (i.e. plug it in and mount the drive by connecting to server) but TM fails if I try to use it for TM backups.
The machine is a NAS, what I am trying to figure out is where is the NAS software held? is this part of the build of the harddrive or part of the firmware?
The reason I ask is, you cannot reformat a TC, only delete the network drive you create with various setting for secure delete. BUT, if you look at a TC drive it is NOT the full size of the drive within the TC. Also, there are at least 3 partitions on the drive, So I assume that the other 2 are the NAS side of things. My opinion is that one or both of the NAS partitions is corrupt, but we have no method of rebuilding these and no method of reformatting the entire disk.
I have read that you can remove the TC drive and reformat it using disk utility, but what happens when you put it back in? is it still a TC? does it still have the TC NAS functionality?
What I think is missing here is something in Airport utility that allows you to rebuild a TC from scratch. I assume the reason it isnt there is to ensure that people can't build their own TC's and have to buy Apple's, but surely Apple could build this into Airport utility so that it recognises a genuine TC and allows a re-build and/or re-format?
I am going to continue messing with the old one, to see if it can be fixed, if not it will either become the most expensive airport extreme I won or at least a Network attached disk for my PC's.

XP Machine hangs when plugging in PCMCIA-FBU​S

Similar Messages

Maybe you are looking for

XP Machine hangs when plugging in PCMCIA-FBUS