XP Networking Issue with 10.5.6

I am struggling to get a Windows XP machine to allow access on an OSX 10.5.6 home network.
My details are these;
1. I have a DELL Laptop running Windows XP which is configured for Domain access at my place of work.
2. I have an OSX based home network.
3. I can see the Dell Laptop in the Finder sidebar from my iMac
4. I have File Sharing enabled on the OSX machine, with the SMB option enabled and I have an account set up with the same username and password as on the DELL machine enabled on the mac. This account has been given Read & Write access to a shared folder on the iMac.
5. I can see the Workgroup in Microsoft Windows Network from my Dell Laptop, however if I try to search the Workgroup I get an error message that says:
+"Workgroup is not accessible. you might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The device is not connected."+
6. If I try to access the DELL from the iMac via the Finder sidebar, I get a log on window that asks for a Username and Password but when I enter the DELL Laptop account details I get an error message:
+"There was an error connecting to the server. Check the server name or IP address and try again.+
+If you are unable to resolve the problem contact your system administrator."+
Any ideas?
Thanks,
Chris

Chris –
The problem is most likely due to the fact that you don’t have a local account on your Dell laptop. When you are prompted for a users name are you using domain\username? Give that a try and see what happens. As for seeing the Mac from your Dell that may a bit tricky as your Dell is set up for a Domain. Normally you should not have any problems accessing a Workgroup; however, since you are disconnected from your company’s Domain I am sure that your laptop is not too pleased and is balking when trying to browse your local network. One last item I just though of – do you have access to a local account on your Dell as you may run into a problem when using your Domain account as there won’t be a Domain controller to verify against.
Best of Luck –
BH

Similar Messages

Very Strange Network Issue With Two Guests on 2012 R2 Hyper-V Failover Cluster

Hi all. We're having a odd issue with two guests on our 2012 R2 failover cluster.
In a nutshell, if we shutdown a particular server (I'll call it Server A) another totally different server (Server B) on the same node loses it's network connectivity to the domain. If we start server A back up, network connectivity returns on server B.
At first I thought server A might be running a service that was somehow linked to server B, so I decided to disable server A's NIC. Interestingly, that had no affect on server B's connectivity.
The next step I tried was pausing server A and again, no adverse affect on server B's connectivity.
Next step was to live migrate server A to another node. This action did
cause server B to lose its network connection.
One other clue is that if I ping server B from either of the Hyper-V hosts in the cluster, I never lose network connection to server B.
So I would suspect this is some network issue on the cluster, but I'm kind of at a loss where to go from here.
Has anyone seen this behavior before or does anyone have any troubleshooting suggestions I can try?
Thanks!
George Moore

Hi Sir,
I'v never seen this before .
>>Next step was to live migrate server A to another node. This action did
cause server B to lose its network connection.
They are connecting to same virtual switch ?
First please run cluster validation to check if there is any error .
If it is ok , please try the following items for troubleshooting :
1. shutdown serverA serverB
2. then add another virtual NIC for serverB
3. start server B check if the issue happens to both "old" and "new" virtual NIC .
In addition , you can live migrate both A and B to another node , then try to live migrate A to the original node .
If the issue persists , I would suggest you to remove that virtual switch on both nodes then re-create them .
Best Regards,
Elton Ji
If it is not the answer please unmark it to continue
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected] .

Network issue with initial connections on Hyper-V

This is the opposite of all the other networking issues I have seen with Hyper-V- anyone run into this?
I am running Hyper-V on a Server Core installation, and have had the same issue when I used Server 2012R2 as when I used Server 2008R2 on the same server as a virtual host. The server is an HP ProLiant DL360 Gen8 with 2x 8-core processors, 32 GB RAM. The
VM is sized and configured to stay within 1 NUMA node. It uses a single port of the 4-port HP/Broadcom 331 NIC, with all the TCP LSO settings disable at the switch, host, and guest, same with the power management settings. We have ProxyARP on the network,
so I have set the ArpRetryCount key to 0.
I have seen it happening with and without SR-IOV enabled. The guest OS is an RDS server, so for the sake of our CAL's it has to stay at Server 2008R2. I have set up a HOSTS file to mitigate this problem, as it seems to be a DNS issue- Here's what happens:
The first time I visit a resource, the server will timeout. An example not in our HOSTS file does this consistently: If I go to https://mail.mydomain.com/OutlookWebAccess, it spins for a couple of minutes before timing out. I hit refresh and the page loads
immediately. This server is colocated in-house, as is the mailserver. I'd say it is a DNS issue at some level, but I'd like to know what level it is- Is it just timing out trying to cache the DNS request, or is there a performance issue with a DNS server on
the network? (All of our DNS is AD-integrated running on DC's).
Here is where I'm seeing this:
Internet Explorer- described above
Salient Interactive Miner- at the login screen, it searches for a database and times out. If I go to the setup and enter the IP address, it still times out. It will not find the database server until I quit and restart the program. If this is the same issue,
it would obviously not be a DNS problem.
I DON'T see it in GP9 connecting to a datasource
Prior to setting up the HOSTS file, I saw this in Windows Explorer connecting to network shares on the same LAN segment.
This appears to only happen to the Hyper-V guest OS. As a best practice, whenever Windows Update runs, I update the Integration Components.
I have the bindings properly ordered on the guest VM, with the network adapter the goes to the physical NIC first, and IPv4 ordered before IPv6.
All updates are isntalled, and the firmware is at it's latest revision.
Any ideas?

Hi Daniel,
" This appears to only happen to the Hyper-V guest OS. "
Do you mean that any other hosts can access the network resource normally except these VMs ?
If yes , my suggestion is to disable the VMQ on the physical NIC for the VMs , then try test again .
Best Regards
Elton Ji
If it is not the answer please unmark it to continue
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Networking issues with MacBook Pro

I have tried to find this issue on line and in the forums and couldn't I have seen many people have similar issues using VPN connections or Citrix but nothing what I am seeing. I have 3 MacBook Pros that connect fine to our company network. They have the DNS settings from our DHCP server and I can see their leases and everything. We can connect to network drives however we can't connect any of them to the company's intranet sites. If we type in http://companysite and hit enter both Safari and Firefox come back stating that they can't find the server companysite. Not sure why it is looking for a server by the name of companysite when our DNS servers point to the servers that are hosting the sites.
If I type in the IP address of any company site then it works however using the name doesn't. So it sounds like an issue with DNS but again the DNS servers are in the network settings and Windows machines have no issues with using the http://companysite instead of using http://IP Address. Any assistance would be appreciated.

OK, figured out that if I added my company's domain to the search domain list in Network Settings this would allow the MacBook to use http://companysite instead of the IP Address. However now I need to figure out the authentication issue. We use the end user's network credentials for access to the company intranet sites. Using http://companysite I get access denied. Using the IP address allows the end user to enter in their network credentials.

Network Issues with Visual Studio Online Application Insgihts

My team is using Visual Studio Application Insights to monitor availability of our web server (we use cloud service)by making a call to it every 5 minutes from different locations around the world including Singapore, Japan, France and Switzerland.
We experienced continuous failures of this monitoring from Singapore from September, 19-th and the issue became very big on September 21-st, September, 22-nd. After that on September, 23-rd and 24-th we have failures form Paris. Then starting from September,
24-th to September, 26 we have very high percent of failures from Japan. Our problems finished with one more failure coming from Switzerland on September, 26.
I wanted to find what the source of the problem is since we checked our code and it very simple to cause network issues. However, it is very difficult to reproduce the issue. My questions is - were all these problems coming from Visual Studio Online Application
Insights?
One example error that it is tracked in Visual Studio Online Application Insights is:
System.Net.WebException: Unable to connect to the remote server ---> System.Net.Sockets.SocketException: A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because
connected host has failed to respond 138.91.9.51:8080
   at System.Net.Sockets.Socket.EndConnect(IAsyncResult asyncResult)
   at System.Net.ServicePoint.ConnectSocketInternal(Boolean connectFailure, Socket s4, Socket s6, Socket& socket, IPAddress& address, ConnectSocketState state, IAsyncResult asyncResult, Exception& exception)
   --- End of inner exception stack trace ---
at System.Net.HttpWebRequest.EndGetResponse(IAsyncResult asyncResult)
   at Microsoft.VisualStudio.TestTools.WebStress.WebTestTransaction.ResponseReceived(IAsyncResult result)
   at System.Net.Sockets.Socket.EndConnect(IAsyncResult asyncResult)
   at System.Net.ServicePoint.ConnectSocketInternal(Boolean connectFailure, Socket s4, Socket s6, Socket& socket, IPAddress& address, ConnectSocketState state, IAsyncResult asyncResult, Exception& exception)
Thank you!
Kanio

Hello Kanio,
There is nothing AI-specific in the stack, and, since the exception was reported to the portal, I would say that AI was working that time. However, if the issues goes away as soon as you disable AI - then it might mean that the issue is induced by AI presence.
Also, you can try the latest AI SDK (0.13 as of today) and see if the issue still happens.
Dmitry Matveev

Networking issue with Leopard 10.5.2, Arris Touchphone, Netgear WRG614 v4

I recently upgraded to Leopard 10.5.2 and now having long hang times of 15 seconds (if I connect at all) to internet. It's not a signal issue, AND I have a PC that flies on same wireless network.
The same time I loaded new OS, Comcast came in a changed out my Motorola SURFboard SB5120 modem for Arris Touchtone Telephony modem. I am still using the Netgear WRG614v4 with the most updated firmware(V5.0_07)
Of course, I wasn't sure if not being able to connect to internet was a Leopard issue or a networking issue. After many hours of troubleshooting...
1. MANY hard resets through cable company AND buttons on both modem and cable
2. Applied all the newest Updates to 10.5.2 which fixed the issue for about 2 hours, then back to crawling
3. Changed the channel on the Netgear from 11 to 9
4. Went to Starbucks AND Panera Bread and had fast connectivity even from the parking lot!
Although I expect some issues to pop up from the new OS, I now believe the connectivity issue is with either the new modem or router. Comcast insists that their firmware is up-to-date and is automatic.
Should I get a new router? HELP

I've been on the road and everything is working fine, but now I'm back home and the same issues.
BUT for some reason, after a day, something switched up and now the mac is on-line and the PC is not. They are definately fighting each other. Even the wireless printer is wacked. Sometimes when I try to print from the mac, it can't connect to the printer. I then either restart the mac or restart the printer, and it goes through.
The other issue now is that all the lights on the Arris modem are blinking. Comcast is saying something is wrong. They are coming out today. Wonder if I just got a bad modem....

10.4.8 network issue with some routers (Zyxel)

Since I have installed 10.4.8 there is a problem with my Zyxel Prestige 310 router, which after a short period of time "hangs up" - so nobody in the network has Internet conection ( PC's and other Macs with 10.4.7).
After restarting the router everything works fine, until I start a Mac with 10.4.8..
This happens on Intel and G5 Macs..
Today I had a long phonecall with my Provider here in Austria, who told me that a lot of people are having this problem - all with Zyxel Routers - but he doesn't know a solution.
He (and me) is waiting for a fix from apple...:-)

I also have an issue with the 10.4.8 update and a Zyxel router, although mine is not as severe as yours.
Mine has to do with WPA encryption and a timeout setting.
The thread is here:
http://discussions.apple.com/thread.jspa?messageID=3246932
So, maybe this helps?
MacBook white, 2.0 GHz, 1,25 GB RAM Mac OS X (10.4.8)

Network issues with Apple products?

I've got a weird issue with my Apple products connecting to certain networks. Two different instances:
1) My parents house, my iPhone, iPad, and MacBook Pro all have issues in contacting certain sites and apps. Things from google or apple servers wont work. Some things do, if I VPN to an outside network, everything works perfectly fine. I haven't been able to figure out what the root of the issue is. I've switched routers and contacted the network provider but they said it wasn't there fault. This has been going on for a bit. All non-Apple products seem to be fine.
2) My office, I know even less details about the network here, but I'm having a similar issue where my Apple devices get connectivity for a bit then stop and then come back later. If I VPN again, everything works perfectly fine. All non-Apple products work fine.
Anyone have any idea as to what this could be from?

I am having the same problem since upgrading to Snow Leopard. Really need an update from Apple or a solution. Been reading a lot of posts on several discussion boards but nobody has come up with a solution yet. Apple really needs to send us a fix for this. I understand it is also hapenning in Lion.

Networking issue with D110a

Just swapped out routers (Belkin to Airport Extreme). Lost connectivity to printer, and have been able to reconnect with USB and going through USB port on Airport Extreme. Problem is I can't get the printer networked as Bonjour Multifunction...get the following: "An error occurred while trying to add the selected device. Unable to communicate with the printer at this time". I have updated the network password on the printer and it has an IP address with good signal. Printed configuration page says everything is OK. I have unplugged, restarted, reinstalled EVERYTHING, to no avail. BTW, when I try to check for updates on the printer itself, I get the a Server Connection Error:
Any advice would be appreciated.

Hello @wfriedmanct,
Welcome to the HP forums.
I understand that you have been having some networking issues since you switched to the Airport Extreme.
I would like to help.
The router may need to have some adjustments made.
~ Multi-casting needs to be on or enabled (Allows Bonjour Connectivity)
~ Wireless Ports, these can also be blocked in security software:
Incoming (UDP) ports : 137, 138, 161, 427
Outgoing (TCP) ports : 137, 139, 427, 9100, 9220, 9500
~ Our printers only support 2.4 GHz not 5GHz
~ Recommended that the network name and password DO NOT contain and spaces/punctuation or special characters
~ Dual broadcasting enabled (for wireless b/g and n networks)
If you are getting a server connection error then the printer either does not have internet access or is getting lost.
I would try a manual DNS.
The following reply by happytohelp01, has instructions for setting the manual DNS.
It is for a 7510, but the steps will be very similar. If you get stuck, please let me know.
You also may find the following document useful in your situation.
Setting Up Your HP Printer on a Network with Apple AirPort
Aardvark1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!

Network issue with iPhone 5s and iOS 8

Hello,
i am using iPhone 5s and iOS 8 updated till date.. I have having an issue where my Vodafone network suddenly shows no signal .. It never happened before. iOS 7 never had this problem. What do I do. I did a few things as discussed in earlier network issue questions. Vodafone never has reception problem.. since I installed iOS 8 I am facing this problem . What do I do now..

Hello, Aniket2210.
Thank you for visiting Apple Support Communities.
I understand that you are experiencing an issue with your iPhone searching for service and no signal. If you have not resolved this issue, I would recommend trying the troubleshooting steps in the attached articles below.
If you see No Service or Searching in the status bar of your iPhone or iPad
http://support.apple.com/kb/ts4429
iPhone cellular data connection issues
http://support.apple.com/en-us/HT201415
Cheers,
Jason H.

IPhone 6 "no network" issues with vehicle

My iPhone 6 pairs with my Range Rover no problem, plays music via the iPod from the iPhone. However, it will not allow for phone calls while in the vehicle using Bluetooth. Just says "no network."
Tried:
Resetting phone
Resetting network on phone
Deleting and repairing phone from vehicle numerous times. No matter what it still says "no network" on my screen display for my Range Rover.
However my iPhone 5S WITH IOS 8 DID work without any issues. So it's not IOS 8.
Tried pairing it with a friend of mines car and same thing. No Network.
I really hope this can be fixed by Apple through a software update because if it's a hardware issue with the new iPhone 6, things will start getting interesting
as I've seen this issue in other threads already and is going viral slowly......

iPhone working fine now in the car, I can call and receive ok and audio is good.
however I can skip tracks forward on the steering wheel and iPhone but can only go backwards to the start of track playing? Not a major problem but everything is ok.
i fixed this by resetting all settings, the network settings only delete all your wi-fi codes. Hope this helps..

Strange Networking Issue with OES

Since moving our entire infrastructure from Netware to OES, I've been trying to figure out a very strange issue. We are a K-12 school system with a data center at the central offices and a single server at each school. The data center has the servers that run all the centralized stuff, including the Master replicas for [root], the DA's for SLP, etc. We noticed that sometimes a school's server will drop out of the SLP tables. When that happens, we also cannot SSH to the school's server from the central servers. We can SSH to it from any other machine on the same subnet as the central servers. The central servers can ping it, but no UDP/TCP traffic can pass between them (no web traffic, etc). We finally realized it only happens when the ISP that serves that school has a brief blip or outage of some sort. The only way we have found to get the servers talking again is to reboot the central servers.
We have tried:
Restarting almost all services on central servers
Stopping and restarting networking
Switching to runlevel 1 and then back
Stopping firewall and/or shutting it off completely
Checking hosts.deny files
Disabling virus scanner (McAfee Enterprise)
Changing vmware network drivers from E1000 (known issue with vSphere 5.1) to VMXNET3
All servers run on HP Proliant servers (blades at central office, towers at schools) running vSphere 5.1. Links between the central office and schools are all 100Mbps fiber via two different ISP (depending on the school's location). A restart of the central office server fixes it every time. I am out of ideas now and at a loss as to why this happens when a WAN link goes down. We thought it was just isolated to one ISP, but it was just that that particular ISP is not quite as reliable as the other. We had an extended power outage at a school served by another ISP over the weekend and saw the same issue with that server after power was restored.
Any ideas or suggestions at where else we should be looking? We also run ZCM 11 at each school and the central office. When this happens, those servers never lose connectivity with each other and with the OES servers on each end. The ZCM servers run on the same vSphere host as the OES servers.

On 04/08/2014 12:26 PM, jmlester wrote:
>
> Since moving our entire infrastructure from Netware to OES, I've been
> trying to figure out a very strange issue. We are a K-12 school system
> with a data center at the central offices and a single server at each
> school. The data center has the servers that run all the centralized
> stuff, including the Master replicas for [root], the DA's for SLP, etc.
> We noticed that sometimes a school's server will drop out of the SLP
> tables. When that happens, we also cannot SSH to the school's server
To be clear, while i think this correlation is possible, I do not see any
possibility of causality in here unless your SSH client is somehow using
SLP to resolve the SSH server, which seems very unlikely. I'm not sure if
you're trying to state that SLP is the cause of the SSH stuff, but I do
not think you are.
> from the central servers. We can SSH to it from any other machine on
> the same subnet as the central servers. The central servers can ping
> it, but no UDP/TCP traffic can pass between them (no web traffic, etc).
Hmmm........... so routing works, and the server is even responding to
requests made to it (presumably, or something else is), but SSH is not
responding, or something is preventing it from responding.
> We finally realized it only happens when the ISP that serves that school
> has a brief blip or outage of some sort. The only way we have found to
> get the servers talking again is to reboot the central servers.
>
> We have tried:
>
> - Restarting almost all services on central servers
> - Stopping and restarting networking
> - Switching to runlevel 1 and then back
> - Stopping firewall and/or shutting it off completely
> - Checking hosts.deny files
> - Disabling virus scanner (McAfee Enterprise)
> - Changing vmware network drivers from E1000 (known issue with vSphere
> 5.1) to VMXNET3
>
>
> All servers run on HP Proliant servers (blades at central office, towers
> at schools) running vSphere 5.1. Links between the central office and
> schools are all 100Mbps fiber via two different ISP (depending on the
> school's location). A restart of the central office server fixes it
> every time. I am out of ideas now and at a loss as to why this happens
> when a WAN link goes down. We thought it was just isolated to one ISP,
> but it was just that that particular ISP is not quite as reliable as the
> other. We had an extended power outage at a school served by another
> ISP over the weekend and saw the same issue with that server after power
> was restored.
>
> Any ideas or suggestions at where else we should be looking? We also
> run ZCM 11 at each school and the central office. When this happens,
> those servers never lose connectivity with each other and with the OES
> servers on each end. The ZCM servers run on the same vSphere host as
> the OES servers.
I'd get a LAN trace from both sides at the same time. At the very least,
run tcpdump as shown below on both the central office machine as well as
the remote machine to see how the packets differ when trying different
things. If you do a test and do not see output on both sides, do it again
writing it to a file and post somewhere for us to review. Note: since
it's an SSH problem I would either NOT SSH into the system, or I'd be sure
to limit the tcpdump capture/output to something specific to the
connection being tested. Tracing something over which you are sending the
tracing data is never fun since every packet picked up causes another
packet to be generated, to be picked up, to be generated.... ad infinitum.
To see tcpdump output with limited details on the screen:
Code:
sudo /usr/sbin/tcpdump -n -s 0 -i any -vv
To write tcpdump output to a file:
Code:
sudo /usr/sbin/tcpdump -n -s 0 -i any -w /tmp/problem-20140408.cap
While filtering when capturing is typically not desired, you can do it by
adding something like 'host 10.1.2.3' to the list of tcpdump parameters at
the end of either of those two commands. The reason filtering during
capturing is not desired is that you may miss something.... the SLP
traffic, DNS, ARP, ICMP error showing the exact problem, etc.
Good luck.
If you find this post helpful and are logged into the web interface,
show your appreciation and click on the star below...

Networking issues with Windows SBS Server 2003

I have 3 G5 running on a recently installed 10.4.8, they were all previously running 10.3.9. They all connect to a network drive with folders that have color labels on them (only 2 blue and green). In 10.3.9 the labels were fine, now when the machine connects to the server the labels do not refresh utill you have been throught them and selected them all. I have tried delabeling and then relabeling them in 10.4 but it does not help. I have also tried it on another site and it does exactly the same. It also does not seem to matter what protcol you use to connect to the server (AFP, SMB, TCP/IP).
Anyone come across this before and know any fixes?

I dont really have much to offer here except that we use afp with our SBS server and this hasnt come up... on any of our 10.4.x machines.

New Airport Network - issues with some specific features

Hello,
I have just changed my wifi system for an Airport Network, with one AirPort Extreme and 2 AirPort Express. The goal was to extend the wifi network to the entire house. Everything is fine, all my computers are able to connect to the network and are able to access the internet. The AirPort Network is connected to the internet with the PPPoE procedure.
The issue is very specific here.
1. I use Outlook 2007 to handle my e-mails. Since I have shifted to the AirPort Network, Outlook is not able to connect to pop server anymore for 4 of my 5 accounts. Hotmail (pop) is functionning alright but Gmail is blocked !
2. Windows Update is also unable to connect to the appropriate server.
Maybe there is more but it's all I have noticed so far. I have not changed a single parameter by myself on my computers and both are affected the same way.
I first thought it was a firewall issue but disabling my software firewall (Bullguard) did not change anything. Vista Firewall is not active. Maybe is it the internal firewall of the AirPort Extreme ? But that would not explain why Outlook can send messages (smtp works fine).
Any idea or similar experience ? Thank you in advance.
Best regards,
AdG

Maybe my problem is just bad luck ! I might have shifted to my new network
the wrong day. One day earlier, I would not have seen any difficulty... if this is it.
Quakes slow cyber connections
By Zhu Shenshen | 2009-8-18 | NEWSPAPER EDITION
SHANGHAI'S international Internet connections slowed significantly yesterday after earthquakes rocked Taiwan and southern Japan. It was unclear last night how long repairs might take. Millions of Chinese Netizens were unable to connect to overseas Websites or use popular online chat tools yesterday afternoon.
About 15 million MSN instant message users in Shanghai and other parts of China were affected as the main servers are in the United States. Connections to most overseas Websites including those run by Yahoo and the New York Times were also clogged.
The chain of events that led to the service disruption had its origin in Typhoon Morakot, which struck Taiwan on August 7 and led to a later breakdown in an undersea telecommunications cable system.
Local Internet traffic was not influenced because transmissions were routed to a backup channel. But that cable failed yesterday near Busan, South Korea, apparently the victim of the earthquakes, according to China Unicom.
The failure affected Asian communications to the US and Europe.
The epicenter of the first quake, which struck at 8:05am yesterday, was about 188 kilometers southeast of Hualien on Taiwan's east coast at a depth of 11km, the island's weather bureau said. The US Geological Survey put the magnitude at 6.7.
The second quake, which was centered close to the first at a depth of 20km and struck at 6:10pm, measured 6.1, the Taiwan weather bureau said. It was also felt in Japan's Ishigaki Island.
"We've sent a team to repair the broken cable, but we can't give a detailed timetable for when it will be completed," said Song Guixiang, a public relations official for China Telecom.
The schedule will depend heavily on weather conditions, Song said.
Repairs are handled by a team comprising the carriers that use the cable.
In most cases it takes one to two months to fully repair damaged undersea cables. In the meantime, telecom operators will try to reroute traffic to operating cables and satellite systems.
Domestic Internet connections and international call services were normal yesterday, the carriers said.

Networking issues with bridged connection

So in my network I have a netgear C6300 with a Motorola surfboard(modem/router also with dhcp turned off) connected via Ethernet to provide a separate wifi network on the other side of the house. I've been having frequent connection drops that last for about
10 seconds. I figured out my wireless adapter(netgear a6210) is bridged to the Motorola(see screenshot) and I'm wondering how to disable this bridge because I think it might be causing the connection issues. But when I try to remove the bridge is says gives
an error. If I disable the Network bridge my adapter stops working. Any ideas?
Note: before it was saying Motorola... under the enabled, bridged.
Edit:
This: I also noticed it switched from Motorola like the picture below to NETGEAR58-5G(like above)

Hi slycoder127,
If yo uare currently running Windows 10 build 10049, then you should take a look at the thread below:
No access to Internet Protocol (v4 or v6) in 10049
Which might cause some of the adapter function not working at the current build.
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Office Network Issue with MacIntel

OK, this makes sense to me but might be tricky for someone else.
I have an office of 7 Macs, all on an ethernet network. We want full access to eachother's Home folders so here's how we connect to eachother: if I want access to John's computer I connect to it by signing in as him. As such, I have full reign to his hard drive. Once I've done this once, I can create an alias and then just double-click the alias to regain access to that person's drive. We like it this way; there are no trust issues.
Everything worked fine until we got a MacBook. We can still connect as we did in the past and the alias works UNTIL the MacBook restarts. Once this happens, the alias no longer works and you've got to go through the more laborious method of Connecting to Server, selecting the computer,...

I cannot replicate your error. I logged into my server from my macbook. Created and alias of the mounted volume. When I reboot and double click the alias it prompts me to log into the server again. I subsequently checked the box 'remember password in keychain' and now the alias works without prompting me to enter a password.
When you initially logged into john's computer to make the alias of the network volume did you login via and IP address or a bonjour name i.e johnsmac.local ? How is your macbook connected to the network?
You could try restarting the file server on john's computer. You could trash the apple file server preferences on john's computer.
/Libarary/Preferences/com.apple.AppleFileServer.plist
Or you could create another method to log into the server
in your webrowser enter the following address
afp://john:password@johnsmac
replace john:password with the actuall login and password, and replace johnsmac with the server address.
Then drag the address to your desktop to make a bookmark, then you can double click that to log into the server.

XP Networking Issue with 10.5.6

Similar Messages

Maybe you are looking for