XP Pro on MacBook Pro Cannot Connect to AirPort Network

I just installed Windows XP using the Boot Camp set up utility. After I installed Windows, I went to set up a wireless network and went through the full process of setting it up. Since I've done that several times, XP Pro on my MacBook will not connect to my AirPort network. I have an airport network on one end of the house and on the other end, I have an airport express to increase the signal.
Any ideas?

I feel your pain! I can tell you how to get into a protected net ... just not how to STAY connected for any appreciable time! Haven't figured that one out!
Go to your wireless connection icon ... bottom rhs of tool bar (XP)
- 2x click that icon ... that'll bring up your connection
- Highlight your connection
- Select the "Change Advanced settings"... lower lhs of screen
- When the next window pops-up, select the "Wireless Networks " tab
- The next window should display your connection ... if not highlight it
- Select properties
- In this window you should select:
- Shared for Network Auth
- Select WEP for Data Encrypt
- Input your Network Key (You can get this off your Airport Admin Utility by bringing up the Airport and selecting the "Lock" icon that's named "Password". Select password and it'll give you the hexadecimal equivalent. Input that into your Network Key window and authenticate.
- Select OK and you should be good for about 5 mins!

Similar Messages

HT204135 I recently migrated from a 2 year old MacBook Pro to MacBook Pro Retina and now cannot get my LaserJet 3200 to print. I downloaded drivers from HP Support site but printer just prints a line of gibberish per page, and many pages.

I recently migrated from MacBook Pro to MacBook Pro retina. Now my macbook will not print to my LaserJet3200 printer. I downloaded the drivers but still only prints a line of gibberish per page, and endless pages, when i send printer a print job. Any recommendations on how to correct this so the printer prints properly again?

Hi
where can I find the "generic PCL driver" you referred to Greg?
Also, I searched for a LJ 2100 d4river and found these. should I be working with the HP website? or an apple website? my Apple software update is current.
Find by product
Go
How do I find my product name / number?
5 matches found. Please select one below
HP LaserJet 2100 Printer series
HP LaserJet 2100 Printer
HP LaserJet 2100m Printer
HP LaserJet 2100se Printer
HP LaserJet 2100tn Printer
HP LaserJet 2100xi Printer

Officejet Pro 8600 - Macbook Pro and Macbook Air will not print

Products:
HP Officejet Pro 8600
Macbook Pro (Mac OS X, Version 10.7.5)
Macbook Air (OS X, Version 10.8.2)
Question:
Why did my Macs initially print fine, but now will not print at all?
Full Story:
I have a wireless network at my house that consisted of a 30mb cable internet, Netgear 900n, HP Officejet Pro 8600, 2 Dell Laptops with Windows 7, a Lenovo Laptop with Windows 7, and Dell Tower with Windows 7 - All printed just fine.
The HP Officejet 8600 was added to my network about 2 months ago.
I added a Macbook Pro and a Macbook Air about 3 weeks ago. Both Macs printed just fine for about a week. Then suddenly they stopped. I spent about 2 hours on the phone with HP Service, and they finally said it must be my router. So I called Netgear. Netgear was useless! They wanted me to agree to charges for services before they would even discuss the issue.
Due to information provided by HP's service support, and because Netgear will not support their product, I promptly purchased a new router - an Apple Airport Extreme.
The Macs recognize the printer, will print if hardwired via a USB cable, but will not print wirelessly to the Officejet Pro 8600. The PCs print fine.
The frustration that is being felt is compound by the fact that the Macs printed just fine with the Officejet Pro 8600 2 weeks ago, and now the printer just shows "idle"... even with a new router. (see image below)
Please help, I appreciate any support.
As a side note, the HP Service rep was very friendly, and definitely tried to support the HP Product, which is much more than I can say about Netgear.
Thank you,
This question was solved.
View Solution.

Hi,
More likely the issue related with Multicast, which Apple devices relies on to communicate with teh device through the network.
First try unplugging the router for 30 seconds.
Plug it back to the power and wait for 2-3 minutes.
Turn the HP printer Off and back On, then check for any difference.
If the same persists, try changing your router configuration as following
Note: the settings below are not related with the HP product, I provide you the steps as a best effor and those are only based on my own knowledge. you may try modifying the router settings at your own risk:
Open the router configuration page (can be found listed as the Default Gateway by clicking the Wireless icon on the printer, then print a network configuration report.
Click the Advanced tab.
Click the Setup option from the menu, then click on WAN Setup.
Make sure to uncheck the box next to Disable IGMP Proxying and Apply the changes.
Click the LAN Setup on the same Setup menu.
Set the RIP Version as RIP-2 and Apply the changes.
Reboot your router and then check for any change.
I hope you may find that information useful, you may also use the user guide below for further information:
http://www.downloads.netgear.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.pdf
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Does it worth to move from macbook pro to macbook pro retina?

Hey
I have macbook pro with
Processor 2.66 GHz Intel Core i7
Memory 8 GB 1067 MHz DDR3
Graphics NVIDIA GeForce GT 330M 512 MB
and its good but many people are saying macbook pro 2013 with retina display is the best laptop and has many features so do you advice me to move from macbook pro to macbook pro 2013 with retina display?
thanka

It's a very sweet machine, of course. Although the upgrade path is a bit dicey. Just my opinion, but unless you have very demanding graphics needs (in which case you probably should have a desktop system with a huge monitor), I don't see the point of spending all the money. Probably you would get more value if you take your current machine and max out the RAM and get an SSD.
It's hard to advise anyone in such matters via the internet.
Here are some good reviews:
Apple MacBook Pro with Retina Display Review (2012)
MacBook Pro with Retina display (15-inch) vs. MacBook...
By the numbers: 13-inch Retina MacBook Pro vs. other MacBooks ...
13-inch MacBook Pro w. Retina vs. old MacBook Pro vs. Sony Vaio ...

I am thinking of getting my first Macbook pro for uni and was just wondering which one would be the best? The macbook pro or macbook pro with retina display? or even wait for the new release in 2013 ?

I am thinking of getting my first Macbook pro for uni and was just wondering which one would be the best? The macbook pro or macbook pro with retina display? or even wait for the new release in 2013 ?

If your budget is unlimited, look at both the retina and non-retina and make a decision based on your preferences. If funds are tight, explore the options in the refurbished section. Unless you are dealing with courses that demand specific performance parameters, any one of these options will suffice.
Ciao.

Will Lion 10.7.x run on MacBook Pro 17", MacBook Pro 2,1 with Intel Core 2 Duo, 2.33 GHz ?

Will Lion 10.7.x run on a 63-month old MacBook Pro 17", MacBook Pro 2,1 (2GB RAM) with Intel Core 2 Duo, 2.33 GHz ?
Currently running Leopard 10.5.8 and about to update to Snow Leopard.

It will run, if that's what you want. I'd think twice though. If you want to try Lion, upgrade your RAM to the max: 4GB's(Apple says 3, but your machine will run 4), however only a little over 3GB's will be able to be addressed(limitation of your computer). IMO, Lion needs a minimum of 4GB's of RAM to function properly. In your case, you'd be a little shy. I'd suggest you go to SL & stay there.

New Macbook won't connect to existing network

Hi there,
I've just got my new macbook, and it won't connect to my wireless network. It comes up with an error message saying it cannot connect to the network. There's no hint of what the problem is. I have another laptop which connects to the network fine. Is it a password issue? And if so where do I go to change the relevant Airport settings?
Thanks
J

The System Preference, Network, is where you change these things. However, it will only ask for a password when you try to connect, and it needs one. If it didn't ask, the network doesn't have a password. If you tried to enter one before, you can try deleting the Keychain that holds the wireless password. Open Keychain Access from the Utilities folder. Look for your network name in the list of items and delete the one with that name. If you have more than one, that may be the issue. Just delete them and start over trying to connect. Otherwise...
We need to know more about the wireless network. Open, WEP, WPA? Type of router? What are the router settings?
What are the MacBook settings for the Airport Network settings? Is it set to join automatic or preferred networks. Try adding your network as a preferred network and try that.
The following are things that may work. Sometimes preference files prevent things like this, even on a new MacBook.
There is also a preference file, /Library/Preferences/System Configuration/com.apple.airport.preferences.plist that controls some of the global Airport items. Try moving it to the desktop and then open system preferences and re-configure the network settings. Also there is preferences.plist. It has all of your network configurations and locations. If you move it, you'll have to add all of your network interfaces back into the Network Port Configurations and any Network Locations you may have made.
You can always move them back if it doesn't help, but you'll have to overwrite the new ones that were created. You must be an admin user to do this.

Iphone 3GS "cannot connect to data network"

Ever since I updated to the new operating system, my phone (3GS) hasn't worked properly. Sometimes with 3 or even 4 bars of 3G I cannot make phone calls or send text messages or use the browser. I feel like I've tried everything; I have: restored it, restarted it, reset network settings. I receive the "cannot connect to data network" very often, extremely frustrating. If anyone has any fixing advice, it would be greatly appreciated. Thanks

If no change after restoring your iPhone with iTunes as a new iPhone or not from your iPhone's backup, there may be a problem with the SIM card. Contact your carrier which should be Rogers with a 3GS, and request a new SIM card.

TS1398 I did everything you are recommend to do and still cannot connect to the network. "Unable to join network" shows up even that is a university network working for other users - students and staff. I am very unhappy with my new iphone 5 :(

I did everything recommended on apple store support site and still cannot connect to the network with my new iphone 5 but my co-workers and students (I work for the university) can keep connectivity all the time. I am very unhappy with my new phone

Be patient, Apple is coming out with a update soon, its been reported that they have sent the update to the carriers to test, which means it will be soon. And is suppose to address this issue.

I have done the step 1 to 3,but still cannot connect the wireless network?

i have done the step 1 to 3,but still cannot connect the wireless network?

Step 1 to 3 of what? Can you elaborate on the issue?

G4 (800MHz) connects to airport network via N300 wireless modem but won't bring up a browser page (Safari or Firefox)

G4 (800MHz) connects to airport network via N300 wireless modem but won't bring up a browser page (Safari or Firefox) - so the connection is there, everything says its a goer - I get a clear black signal icon in the menu bar on top, and a clear signal strength in the Internet connect dialogue box - - but when I run either of the browsers, it just says 'not connected to internet' - even for the 'software update'.
the N300 is a Netgear N300 Wirelsess Modem Router (model DGN2200) - ADSL (802.11 b/g/n)

tests to try:
-- have you tried connecting by cable? What happens?
-- Set your dns to 8.8.8.8 and 8.8.4.4 This is the google dns server. generally faster.
Check out your settings.
apple > system preferences > network
Double click on network connection you are using.
Pick the TCP/IP tab.
Verify that you have a DNS Server.
You can use
harddrive > applications > utilities > network utility
to diagnose the situation.
You can ping google.com.
Result:
Ping has started ...
PING google.com (64.233.167.99): 56 data bytes
64 bytes from 64.233.167.99: icmp_seq=0 ttl=244 time=215.362 ms
64 bytes from 64.233.167.99: icmp_seq=1 ttl=244 time=279.597 ms
64 bytes from 64.233.167.99: icmp_seq=2 ttl=244 time=189.747 ms
64 bytes from 64.233.167.99: icmp_seq=3 ttl=244 time=250.657 ms
64 bytes from 64.233.167.99: icmp_seq=4 ttl=244 time=183.232 ms
64 bytes from 64.233.167.99: icmp_seq=5 ttl=244 time=243.753 ms
64 bytes from 64.233.167.99: icmp_seq=6 ttl=244 time=173.108 ms
64 bytes from 64.233.167.99: icmp_seq=7 ttl=244 time=230.239 ms
64 bytes from 64.233.167.99: icmp_seq=8 ttl=244 time=180.639 ms
64 bytes from 64.233.167.99: icmp_seq=9 ttl=244 time=232.177 ms
--- google.com ping statistics ---
10 packets transmitted, 10 packets received, 0% packet loss
round-trip min/avg/max/stddev = 173.108/217.851/279.597/33.615 ms
If that does not work, try pinging 64.233.167.99 Result:
Ping has started ...
PING 64.233.167.99 (64.233.167.99): 56 data bytes
64 bytes from 64.233.167.99: icmp_seq=0 ttl=244 time=189.655 ms
64 bytes from 64.233.167.99: icmp_seq=1 ttl=244 time=213.471 ms
64 bytes from 64.233.167.99: icmp_seq=2 ttl=244 time=257.873 ms
64 bytes from 64.233.167.99: icmp_seq=3 ttl=244 time=172.745 ms
64 bytes from 64.233.167.99: icmp_seq=4 ttl=244 time=226.723 ms
64 bytes from 64.233.167.99: icmp_seq=5 ttl=244 time=171.883 ms
64 bytes from 64.233.167.99: icmp_seq=6 ttl=244 time=260.308 ms
64 bytes from 64.233.167.99: icmp_seq=7 ttl=244 time=172.963 ms
64 bytes from 64.233.167.99: icmp_seq=8 ttl=244 time=198.840 ms
64 bytes from 64.233.167.99: icmp_seq=9 ttl=244 time=181.215 ms
--- 64.233.167.99 ping statistics ---
10 packets transmitted, 10 packets received, 0% packet loss
round-trip min/avg/max/stddev = 171.883/204.568/260.308/32.247 ms
If pinging 17.254.3.183 works but pinging Google.com doesn't. You have a bad DNS Server address.
I use Google.
Google provides free dns lookup. Their numbers are:
8.8.8.8
8.8.4.4

Brand New MacBook Pro Cannot Connect to Airport Express

Hi all,
Been reading through these pages and I think there are many others with the same problem as me but with no real answer, I thought it wouldn't hurt to ask anyway.
I have an Airport Express which I bought a couple of years ago. It initially worked fine on my old MacBook, I moved house and then it stopped working (flashing amber light syndrome). I got so fed up with it that it has been languishing in the loft ever since.
After a brief stint with a Windows laptop I decided it was time to return to Apple, and I haven't regretted it for a second.....until I got the Airport Express from the loft!
It simply, fundamentally and irrevocably...doesn't work! It's plugged in, amber light flashes but my nice new MacBook Pro just doesn't even recognise it exists. I have tried running the setup utility but at the first screen I am told that no unit is detected, I'm then told to check my Airport card (I assume it means the inbuilt modem which clearly works as I am writing to you guys now!). I can't even progress with the setup after this.
I have tried each of the Airport setup utilities to no avail (lap top cannot "see" AX).
Just as an update, I just connected my AX to my wireless router with an ethernet cable, a new network called 6ad16d appears to be available. Airtunes then works and I can connect to the internet (albeit slowly). I am not happy with this arrangement though as there is no padlock next to the new Apple network so I am worried that it isn't secure and surely I should be able to just plug my AX into the main and my hifi and it should work anyway?....just like it used to!
My apologies for the rambling post and please excuse my lack of computer knowledge. I really hope someone can help!

Fixed! You jut need a girlfriend with a lot of determination....not even sure she knows how she did it. Involved a lot of menus and a lot of swearing.
Surely this should be easier?!

Brand new macbook pro cannot connect to wireless networks

The first time I called apple tech, they thought it was a problem with my internet provider. I've called 4 times now, and I'm still getting the runaround.
I have an old (2001) G4 sitting right next to my macbook pro which can see numerous wireless networks and connect to them all. A strong connection at that. However, my brand new (refurbished) Macbook Pro Intel etc,.... supposedly best computer ever made, . . . . can see the same wireless networks but has never been able to connect. As a student, I saved for a year to buy this notebook so I could work at cafe's & study with my friends. My friends with PC's can all connect to these wireless networks. My friends with older, less expensive notebooks can connect no problem. I have never been able to connect. Bought this peice of junk 2 1/2 months ago - only because I didn't want to be stuck at home anymore with my desktop. Stupid me to trust apple.
I wish I could get my $ back, but I'm now being told that it's 30 days too late. Before they told me it was a minor thing and some software update could fix it. I did as told. downloaded and installed their 10.4.8 thingy - deleted all the keychain stuff - nothing. same peice of junk.
Now they are telling me to go back to the genius bar where folks are just rude to me and tell me they can't help me becuase I bought a "refurbished" model that didn't even save me $25. What do you know.
Anyone having problems like this? Anyone out there who can help me?

Okay,
I apologie for calling it a peice of junk. I know you all probably worship this machine. I'm just really frustrated. I noticed that this is a very common problem - though most of the posts identical to mine have dissapeared from apple.com - this well known defect is all over other discussion boards and websites like macdefect, etc,....
So, can any of you tech gods help me with this very well known, common problem that I haven't been able to fix with 10.4.8 upgrade?
Thanks for your time and assistance,
-mcgrafx

MacBook Pro Cannot Connect To AirPort

Hey everyone,
Today I opened up a brand new MacBook Pro to find that it couldn't connect to AirPort. I use a WEB 40/128-bit hex. Is that a problem? I use a D Link router. Every time it comes up with "There was a error joining the network "networkname"."
Thanks,
Louis.
MacBook Pro 15" | 2.2 GHZ | Glossy Screen Mac OS X (10.4.10)

Fixed! You jut need a girlfriend with a lot of determination....not even sure she knows how she did it. Involved a lot of menus and a lot of swearing.
Surely this should be easier?!

I tried to download video from RCA Small Wonder EZ201 to my new macbook pro. Macbook pro recognizes the device but then message appears that device was improperly ejected when it is still connected. How can I download these videos?

When I connect the RCA Small Wonder to my MacBook Pro, the device is recognized in finder as EZ201. I tried to copy the video files in the folder but within a minute or two, I receive a message that the disk was ejected improperly, even though the device is still connected. I was able to download the first few videos before it stopped working and was able to play them using Perian. However, when I tried to connect the device again, it froze my system and I had to force a shut down by turning the computer off. Why is the device initially recongized but then shows as improperly ejected when it is still connected? How can I download the videos if the MacBook Pro won't allow the device to stay connected?

A picture of a screen that suggests my new MBP Retina never connects to the "Macbook Pro backup ("StefanTimeCapsule")
This is the one that has the files for the backups procured by the Time Machine program. But it can't "connect"-- You 'll see int he sideways pic (sorry!) that the options STILL says "connecting"
Do i have to make these Time Machines more open to connection?

XP Pro on MacBook Pro Cannot Connect to AirPort Network

Similar Messages

Maybe you are looking for