XP64bit installation halts, K8N Neo4 Platinum - No SATA drives found?

My setup:
Athlon 64 3500+
K8N Neo4 Platinum
2GB OCZ 3200 Premier
2) WD Sata 80GB HD's (for RAID 0)
Nvidia 6800GT Extreme VGA
I was recently lucky enough to get my hands on a real Windows XP Pro64bit Extended Edition. I gathered quite a few 64bit drivers which claim to do the job (so they say.)
However I ran into a very strange issue during installation.
My main concern was getting RAID drivers to utilize after pressing F6 during the Windows install. Unfortunately I could not find Nvidia drivers so I went with the Silicon Image Sil3114 64bit drivers I got from their website. Copied them to a disk and thought I was ready to rock N roll. I have updated all BIOS to latest versions as of the date of this post.
Now I went into the RAID BIOS and setup my RAID 0 Array and both SATA drives are shown. All went well in this dept.
I began my installtion of XP64 and pressed F6 to install the RAID drivers. Popped the floppy in and the driver files were copied successfully.
I continued on to the point where you are prompted to setup Windows XP and it searches for any previous installs.
I continue to where I should get the dislmaimer and to press F8, however the install halts and say no hard drives were found. Setup cannot continue.
Any ideas as to why my drives are not being detected during installation? They show up fine under the RAID setup BIOS.
Any info or thoughts is truly appreciated.

You need to make your own floppy for the nvidia 64 ide drivers.
How to install Windows on SATA using F6 to load Drivers
Follow item 1 Obviously usinfg the Neo4 64bit unified driver pack Windows XP Professional x64 Edition
luck

Similar Messages

K8N Neo4 Platinum "Initializing Floppy Drive Controller" problem

When I finished building my system a couple days ago I started it up and found some problems:
First of all I got a long beep and one or two (not really clear) short beeps (this can be a video issue but also a mainboard issue (?)), the computer continues to start up and ends without any screen on my monitor (it switches to standby mode) and the famous(?) "Initializing Floppy Drive Controller" LED combination.
This is what I tried so far:
-1- clean startup (cpu, 1 stick of memory, videocard) reinstalled all components
-2- boot without floppy drive
-3- clear CMOS
-4- tried different memory and different slots
-5- disabled all case usb and firewire options
I am using a PS/2 Keyboard but it seems to work because when I hit the numlock key the green LED comes on.
What should be my next step?
System specs:
Cooler Master Cavalier 3
Fortron FSP400-60THN PSU
MSI K8N Neo4 Plat.
AMD64 3000+ (winchester)
2 x Corsair VS512mb400
HIS X700 Pro 128 mb
Samsung 1614C 160 Gb SATA
PS/2 Keyboard
USB Mouse

Quote from: Wonkanoby on 15-February-05, 20:04:01
http://www.fsp-group.com.tw/english/02_products/01_pc_power_supply.asp?modelid=166&modelname=FSP400-60THN
14a max 12v is not going to run your set up
Thanks for your reply!
I thought this was enough:
+12V1DC : 14,0A
+12V2DC : 15,0A
--------------------------- +
29,0A
Or is this not the correct way to calculate?

HELP! Installation of SATA HD on K8N NEO4 PLATINUM

I finally put together my system
AMD Athlon 64 3200+ venice
MSI K8N NEO4 Platinum
1 GB DDR400 RAM
Etc....
now my problem has to do with the SATA hard drive i bought for it, a maxtor diamondmax10 6L080MO, my system will boot and say "invalid drive" and will tell me to go into the RAID Tool.
I really dont know much about sata interface setup so i would appreciate a step by step walkthru on it, right know im forced to use my old reliable maxtor 20gb,
is it possible to have both the 20gb ata hd and the new 80gb sata drives? how do i install my sata drive?
i was planning on using the small one for software installation and the big sata one for storage
everything on my system is running well so far, except for the SATA drive problem,
PLEASE HELP!

Ceckardt,
You should not need to install any special drives with single SATA that not in a RIAD Array, if you have Windows XP SP2 installed, if you do not have SP2 installed, upgraded to it before doing anything I instruct you to do below.
If you using just SATA hard drive, all you should have to do is plug it in to one of the nVidia SATA connectors on the motherboard and if you have Windows up and running on the old 20GB Maxtor. Start windows and open the Disk Management Window. You get there by right clicking My Computer, menu will pop-up and left click “Manage” a Window will open and on the list on the left side of the call Computer Management, left click “Disk Management”. On the right of the Window you should see all of you drive of you system including you new 80GB SATA drive. You will have to Partition and format it, then it will show in My Computer as logical drive, the drive letter you will have assigned in the Disk Management.
If you need instructions, other the Windows Help to partition and format your drive under the disk manager, just reply or if the drive is list in the disk manage window and you cannot figure out how to partition and format the just start a new post asking for help using the Disk Manager.
If the drive is not listed in the Disk management Window, reply in the post for more help.
Good luck,
Roger

K8N Neo4 Platinum, how to move MBR to sata (make it drive #1)?

I am not sure I am phrasing the question correctly, so bear with me. I have a K8N Neo4 platinum with the SiI3114 controller and sata ports 4-8 (I believe its what they are calling PCB 1.x) with bios v1.D. I moved the board to another box and installed winXP on it. I was running it with IDE hard drives. Everything was working great but the OS was running really slow so I bought a SATA 300 mb/s drive and pluged it into SATA1 (I read about using ports 3 and 4 for raid but I do not want to use the NVraid at all, it is disabled). Then I proceeded to reinstall win XP. In the setup, I deleted the original C partiton and created one on the sata drive and rebooted so that there would be no "C" drive confusion by the winxp setup (have had that problem before and this keeps it from happening). Went through the setup and the sata was correctly reported as "C". Told windows to install itself there but it told me that it needed to write to MBR on the old c drive but that, since I had deleted the partiton, it couldn't and had to format it. So I knew that something was wrong.
So I rebooted and disabled the ide bus that contained the old IDE drive and just left the CD ide bus enabled. WinXP installed fine with no complaints. Then it rebooted and I re-enabled the ide bus in the bios. It wouldn't boot into the partiton I just installed winxp on! To get it to boot, I had to use F11 (the bios boot menu) and select the sata drive. Went through the whole setup winXP thing and rebooted. Same problem, it wouldn't boot the sata drive. :(
As long as that ide bus with the old ide drive is enabled, it won't boot the sata drive! I have rearranged the boot order on the bios every way possible. I opened up the box and moved that ide chain with the old ide drive to the ide2 port and put the dvd drive on ide1. I made the old drive slave and the prior slave master. That didn't fix it either. How do I tell this motherboard that the 1st drive is the sata drive? How do I tell it the MBR should be there not on the old ide drive? How do I fix this? Thanks!

Thank you for your replies! Hans, thank you I will give it a go again doing full formats all the way. I usually use the full format when installing winXP but I did things in a different order than you instructed so I will definately try it.
Aicjofs, thank you, There are 3 hard drives in this system currently. There is the ide hard drive that used to be the "c" drive (a western digital 160gb ata133 7200rpm 8mb cache) and a second ide hard drive that is an extended partition with 1 logical drive with data on it (western digital 300gb ata133 7200rpm 8mb cache). Then there is a sata hard drive in sata1 port with 2 partitions one primary and one extended. The extended partion does have data on it as I moved stuff there after I got winXP up the 2nd time (western digital 250gb sata II 7200rpm 16mg cache). Right now, I have the ide drive with data on it as ide2 master and the old "c" drive as ide2 slave and it is unformatted and contains no partion information (I deleted the partition after I installed the SATA drive and installed winXP). XP won't boot. What happens is that, if I take the winxp cd out, it gives me a "no system" error. If I leave the WinXP cd in it boots that disk. However, if I use "f11" and choose to boot the sata drive, winxp comes up just fine. If I disable the ide bus with the two ide hard drives, it boots winxp just fine.
Edit: bios is v1.D. It feels like this mobo is telling windows setup that the master ide drive is the first disk and to ignore everything else. It feels like if I can just tell the mobo that the sata drive is the first disk then everything will work . It is late night where I am now, and I've been fighting with this since the afternoon so I might have to goto sleep but I will be back at it tomorrow and will go though what Hans instructed. If anyone has any otehr ideas, I'd really appreciate that as well.

SATA drives not being detected - K8N Neo4 Platinum

I have the same problem, different PSU!
msi k8n neo4 platinum pcb 1.0
3000 64 939
corsair 1gb dual channel ddr400
nvidia 8800gts
antec truepower 550 (19a @ 12v)
used to run 2 ide maxtor 120 and 80
added in a sata dvd writer, worked for 6 months
added in a sata 1TB seagate 7200, sata fails a majority of the time
same symptons now persist as in original post.
:< either bios detects both sata drives, neither, or it crashes. this happens respectively rarely, uncommon, and most common
what ive tried:
updated all mainboard, bios, video drivers to the most up to date (i had to in order for bios to detect the full size of the 1TB)
no ide, same problems
only 1 sata, with and without ide, same problems
the sata only works after a long period of time (or randomly), that i dont use it
(ive had both sata unplugged for 12 hours, booted up this morning with them and it detected, i selected safe mode boot, after making it through a majority of the load, it crashed)
testing a new psu in a day or so, much more powerful. ill give you all my results.

The cables aren't overly bent?
"...worked for 6 months"
"...fails a majority of the time"
Not very relevant, but since i found the FAQs, and there are no less than four FAQs for hard disks http://global.msi.com.tw/index.php?func=prodfaq&maincat_no=1&cat2_no=&cat3_no=&prod_no=165#menu :
"Silicon Image Si3114R Raid bios doesn't have JBOD setting in it, why?
In the new Silicon Image BIOS, JBOD already been renamed as "Concatenation".
If you want to use single SATA HDD or when tou want use each SATA HDD as IDE mode, you can choose "Concatenation" function in Silicon RAID BIOS."
"I am using a SATA hard drive with NCQ technology on this motherboard and I am experiencing problems. How do I fix it?
The issue depends on the Southbridge chipset. Nvidia is currently working on an updated nForce driver to address the issues with certain hard drives.
You could contact Nvidia support to ask for the new driver if there is one. If there is not any new driver to solve the issue, please disable NCQ on your system." /My fattening. /

Largest SATA drive for K8N Neo4 Platinum

I have a system based on the K8N Neo4 Platinum board, I'm planning to up, the storage capacity of my rig and was wondering if I can install a 500 GB or larger SATA or SATA II drive on it?
to make long story short I would like to know whats the largest Hard Drive (either IDE or SATA) one can install on a system with this board without problems or compatibility issues.
I presently have a Maxtor Diamond Plus 80GB SATA drive,
Any takers??? ???

I see no problems, just try it.
As for a Sata-II drive, don't take Maxtor, any other drive should be fine.
However, you maybe must jumper it to SATA-1, depends on the onboard controller.

New Drives - boot Neo4 Platinum from SATA II?

I am going to re-configure my AMD 64 3200+ K8N Neo4 Platinum mobo to have 2 Hitachi T7K250 SATA II hard drives (currently PC has a single IDE drive that will be removed). I have XP PRO original as well as SP2 on a separate disc. Can anyone suggest a course of action here? Any experience with booting from SATA II? I guess I could leave the IDE drive in place simply to hold the OS and put the 2 SATA II drives in for data.

Quote from: Kaplan on 28-June-05, 01:30:10
Those drives "will be" SATA I until you download an utility from the Hitachi website. So they have to be manually configured to be SATA II.
OIC, I am running a T7K250 250GB Sata II Hiitachi as boot drive now. Hardware manager show it is set at Sata I 1.5
If I manually configured it with the Hitachi utility,i.e. boot from DOS as instructed in the website;
Hitachi web site does not say it must be configure before fresh installation of OS or it can be configure when OS is already installed on the drive;
Neither does Hitachi say any thing about configuring a OS installed drive.
Any effect with my installed Windows XP Pro on the HDD?
Willl it be able to boot again? Please help & advise, thanks!!!
By the way I am using MSI K8N Platinum SLi mobo.

K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) -- after POST stucked

hi i'm runningan athlon 3000+ in K8N Neo4 platinum edition v1 (bios W7125NMS V1.6 062305) and i have a very like problem:
today i tried to install freebsd(install started fine, nothing went wrong, i repartioned my hdd and the installer started),
for some reason i had to abort the installation process. since then i can not boot in from any device(cd,usb the hdd is in a
half way to bsd install state so it's not an option atm).
the post screen comes up and i can interact with it in a way(i can press tab and it drops me
to the detailed post screen,ctrl-alt-del also works i can restart with it), but i neither can enter to the BIOS setup /DEL/ nor the boot menu /F11/.
i've tried reseting bios settings by flushing cmos(removed the battery,pressed SW1. something must happened because the post now checks for sata devices
and the graphical screen/that one u can bypass by pressing TAB/ was not presented before).
it also detects my hdd and my cd-rom too. but still nothing happens after the POST.
others said updating my bios would help. but still there is no option to boot from.
if i am doing wrong something please let me know,
thank you for your help
Andrew

the solution:
disable ide1/slave when the broken hdd is not connected and bios accessible; poweroff; reconnect the broken hdd to the PC;poweron; boot from a linux livecd; gpart/fdisk/something to repair the broken hdd;be happy life is nice
the trick was that bios and post is not messing with the broken hdd(while it was blocked in the bios)
so i could boot with a live cd when my hdd was connected to the PC.
since linux trixx out bios i was abel to interact with the post_killer_hdd (even it was blocked in the bios).
i hope somebody will be able to use it one day if something is not understandable drop me a PM.
problem solved im installing the os to the hdd,topic is SOLVED.
maybe the other guy who has some similar issues with his config/hdd could use this post too.
regards,
/\ndrew

K8n neo4 platinum recognized HDD, no boot

there are two sata hard drives in this system, the main drive (which is connected sata1) houses the operating system while the drive plugged into sata2 is a large storage drive. bios recognizes both of these drives, and my boot sequence is floppy-hdd-cdrom with the hdd sequence being maindrive-storage drive. for some reason whenever i attempt to boot it goes through post fine but before it begins loading windows i get "boot from cd:" followed by "disk boot failure, insert system disk and press enter."
i have already made sure that the settings in bios are proper, any help would be appreciated seeing as msi's support request form seems to have an error in the page.
for the record:
k8n neo4 platinum
(2) 1gb pc3200 Corsair memory
Ati x1650pro
80gb sata hdd
120gb sata hdd
generic cd burner/dvdrom/floppy

If you change ur MB whitout formatin' C:// You wont be able to starwindows normally , that msg is normal and restartin too if you're using the same partition onto another MB, you've two options 1st_> backup data from "main HD" to "second HD" and format the first HD or reinstall windows on main partition, for that-> insert win xp boot CD, set up bios from booting from CD DRIVE and then when blue installation screen shows several options select "fix previous Windows xp installation" and that's... The only bad thing of that is that you might also reinstall some programs and thirt party software and you'll spend a lot of space (and performance) in "Temporaly files" from the old previous OS installation, I recommend u choose FORMAT ur main HD, Good luck

Can I put an old 20GB IDE HD into the K8N NEO4 Platinum Board ?

I was just wondering if you can install a old Maxtor 20Gb IDE hard drive into a brand new system built around the K8N NEO4 Platinum (MS-7125) and used it in conjunction with a brand new Maxtor Diamondmax 10 SATA150 80Gb hard drive, for a total hard drive space of 100Gb ?
if it possible for new sata and old ide hard drives to co-exists in the same system ?

Quote from: syar2003 on 23-January-06, 05:00:53
Yes , you can do that .
Only advise is to put the old udma66 disk on it's own ide cable .
You would want to install th OS on the sata drive , make sure not to have the ide disk connected during install
or it will host the OS system files and become the system disk (default win installer choice to take the first drive it sees , and
ide is always prior to satas in bios).
Then after OS is all setup , shut down and connect the remaining disks .
So the procedure would be, to install the sata drive first, the optical drives in IDE secondary and when everythings done, the old 20Gb drive in the primary IDE, its that the way of it ?
what do you mean by "put the old udma66 disk on it's own ide cable" ?

K8N Neo4 Platinum random lock-ups and BSOD

I built a new PC about 3 months ago and from day 1 it has always locked up / frozen at random intervals. Sometimes it also BSOD's with a Machine Check Exception. Seems to lock up / freeze more often when have multifple windows open eg. Multiple IE running but really is random. I have replaced the Mobo and Ram but keep having the same issues. Have tried a clean install but no luck either. Did a clean install on an old IDE HDD and seemed fine but it did not have all of the software that I run on the SATA drive. Thinking the SATA drive may be the issue? Please Help!!!
System is as follows:
MSI K8N Neo4 Platinum [Bios 1.D]
AMD Athlon 64 X2 3800+ DC [AMD Drivers]
2 x Kingston 1024Mb ram [Dual Channel]
Nvidia 6800 Ultra [Latest Drivers 91.31]
Thermaltake Purepower 460W PSU +3.3V 30A, +5V 30A +12V 15A
Western Digital 200G SATA II HDD [SATA Port 5 i think]
1 x LG DVD +-R/RW [IDE Master] IDE port closest to edge of Mobo
1 x LG CDR/RW [IDE Slave]
MS XP Home SP2

Quote from: davePC on 09-August-06, 09:06:44
Did a clean install on an old IDE HDD and seemed fine but it did not have all of the software that I run on the SATA drive. Thinking the SATA drive may be the issue? Please Help!!!
Seemed fine?
There isn't really be any difference between an IDE drive and a sata.
Except that the sata drive needs some drivers as your installing the os.
Check your ram timings in bios but likely it's your psu.
Which components are on which rail?
The ones that use the +12v are your cpu,cdrom,dvdrom and graphics card.
Try disconnecting both roms and see if it improves things?

X2 3800+ (E6) support for the K8N Neo4 Platinum/SLI

Hi everyone:
I have decided to purchase the K8N Neo4 Platinum/SLI (MS-7100-020) and I ready placed the order. However, I wonder if it supports the AMD X2 3800+ (E6 Version) CPU? The reason I asked the question because I found the following table from the Taiwan MSI web site which shows that X2 3800+ E6 is undertesting.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=641&kind=1
Thank you for any replies.

Mine worked, ran for 2 weeks already at stock, tried & ran to 2.2GHz on stock HSF with no problem.
Using X2 3800+ E6, MSI K8N PLI Platinum mobo, 3.7 bios & Inno3D 7800GTX single latest nvidia 78 drivers, 2x512MB DDR400 CL2.5 Kingston Ram, Hitachi T7K250 Sata 250GB HDD, NEC ND-3530A Benq 1640, , Silverstone Zeus 650W PSU
At first I have this concern too, but tried it anyway.
See my screenshots for your info.

BSOD's on my x64 K8N Neo4 Platinum based PC, Any ideas what's wrong? Help!

Over the past few month I've been getting BSOD's. There is no real pattern to their occurence and it's not something which is constantly happening (It happened around 5 times in the past 2 months), but I've really grown to hate them. You see, after getting one what has happened in the past is that when I go to restart my pc after getting a BSOD, I find I need to re-install my whole OS! What happens is that after booting (which oddly enough doesn't work well after a BSOD, It freezes on the boot screen and I need to restart several times), a black screen appears telling me that certain files in the C:Windows\ direcotory are corrupt or missing.
So the real problem is that the BSOD's cause me to re-install my whole OS. One will happen, then it will be ok, I turn the system on, log into windows, then it might happen again, after which I'll need to re-install. The files that go missing are always different too, and when I run scan-disk (after plugging in my main drive into another computer) it finds corrupt files and deletes them.
At first I thought it was Azureus (p2p client) which was causing the problems because it seemed to happen when I was runing that. I stopped using it, and the BSOD's still occured...sometimes randomly when browsing...etc. I figured that since files got deleted and corrpupted, it must be a problem withthe Hard Drive....So I bought a new one, and I've still had the BSOD error (although files haven't been deleted yet).
So yeah, I really need to solve this problem as it is taking away from my productivity and causing me to re-install far too often. I will post the BSOD info as well as my system info below (and a screen shot):
Quote
MACHINE_CHECK_EXCEPTION
*** STOP: 0x0000009c (0x0000000000000004,0xFFFFF80000113BC0, 0x00000000B2000000, 0x0000000000070F0F)
I looked that up on the net, and it seems the first part seems to indicate, or at least COULD indicate overheating. I checked CPU and System temps and they seem acceptable.
I am running Windows XP x64 Edition with the following hardware (please note that all of the hardware drivers I'm using are written for x64, MSI is so good:)). I have had this PC before it started having these problems, it could be related to using x64 I guess, but the error doesn't show that does it?
Quote
AMD Athlon 64 3200+ 2.0 GHz Socket 939 (Venice Core) w/ stock heatsink/fan
MSI K8N Neo4 Platinum S-939 nForce4 Ultra
OCZ PC-3200 DDR400 Premier Series 1GB (2x512MB) Dual Channel Kit CAS 2.5
Ati Radeon x800xl 256MB gddr3, PCI-E
LG 17" L1720B LCD monitor 16ms, 1280x1024
Western Digital Caviar 120GB SATA
Western Digital Caviar SATA II (WD1600JS) 160GB 7200RPM 8MB Buffer
Western Digital Caviar SATA II (WD2500KS) 250GB 7200RPM 16MB Buffer
Pioneer DVR-109 DVD-RW
Pioneer DVR-110D DVD-RW
Antec Sonata II Mid tower ATX black power supply 450 Watt ( ATX12V 2.01 )
Creative I-Trigue 2.1 L3450 speakers
Sony 1.44MB Floppy Disk Drive
Microsoft multimedia keyboard and Microsoft optical mouse (PS/2)
My OS and drivers are fully updated. As for my BIOS I've been running the version I'm using now forquite some time and I believe it is version 1.5. Also in another bad turn of events, my northbridge fan seems to be on its way out of this world (this just happned so I don't think its related to the BSOD). I haven't been able to find a replacement, and since its not spinning very fast, and sometimes stops...It's causing the heatsink to get quite hot. I need to get a new one, and I can't find them anywhere...I wonder if thats covered under warranty... I looked into getting a different heatsink, but my Graphics card is so colse to this heatsink, that theres no room for a bigger one at all.
Do you think this problem is motherboard related, I cannot understand what the technical info the BSOD gives me means, can anybody understand it? I don't think its my HD's, or Ram, or CPU...could it be a motherboard problem? And if so, its under 1 year old, can I get an RMA?
Thanks for the help in advance.

At one time I had a weak 450w psu that had only 18a on the 12v rail. When I overclocked my cpu and gpu, I was getting bsod's every once in a while and couldnt figure it out until I read a similar post like yours on this forum. I decided to upgrade my psu and havent had that problem since.
Power supplies can be deceiving. I now have a 480w psu but its has 30a on the 12v rail. So what we need to know is the ratings of your psu (see my sig) just to see if your psu is the culprit. Just my 2 cents.

Constant HDD access (K8N Neo4 Platinum)

Hello all, this is my first time posting on these forums.
A couple of days ago I put together a new system for myself, with the following components:
* Athlon64 3200+ processor
* MSI K8N Neo4 Platinum motherboard
* 1Gb RAM
* Gigabyte 128Mb GeForce 6600GT graphics card
* 2x Seagate 250Gb 7200rpm SATA drives
* LG IDE dual-layer DVD-RW drive
* Apacer 7-in-1 internal USB 2.0 card reader
* Thermaltake "soprano" ATX midi-tower w/ 400W PSU
The two hard drives I have connected to ports SATA5 and SATA6 on the motherboard and set up in a RAID1 configuration (using the on-board Silicon Image SiI 3114 RAID controller). I then installed Windows XP Professional, which went on fine. The only problem I have now is that the hard drives are being constantly accessed by the system, even when I'm doing nothing on the system. This isn't just an occasional access once every second or so, the little HDD LED just flickers away merrily the whole time. I have run both filemon and diskmon on the system, and found that while no particular files appear to be being accessed, there is almost constant write activity being performed to the hard drives.
I have narrowed it down to somehow involving the Windows XP RAID drivers. If I boot from the Windows XP install disk and load the third party drivers for the SiI 3114, I get the constant disk access when sitting at the first screen of the install process ("Welcome to Windows XP" text-only screen). If I do the same without loading the drivers (thus Windows does not recognise the RAID drive), no disk access. I have tried updating the RAID controller drivers under the Device Manager (now up to version 1.2.0.0), but it does not fix the problem. I have done a full virus and spyware scan (bearing in mind that this is a clean install), with no results. I have checked all running processes and services (including making sure Indexing Service is not running), but have been unable to find anything that could be causing this constant activity. I have yet to try actually breaking the mirror and running the drives off the normal SATA controller. I will be trying that tonight when I get home if no other solution presents itself, but obviously I would rather get it behaving properly in RAID1 if at all possible.
It's driving me crazy. There doesn't appear to be any actual issues with the performance of the machine, but the constant hard disk activity can't be good for the drives long-term. I have searched these forums for a possible solution, and while some people have had similar problems, none of the suggested solutions have worked for me so far. If anyone can help me with my dilemma, I would be Eternally Grateful(tm).

Yes! At least I'm not alone... constant disk ticking is driving me nuts too.
I have same issue with a newly built system - different board but Sil3114.
My C: is on the NF4 SATA interface, but I have 4 250GB Seagaets on the Sil3114, intended for a RAID5 array. Having installed XP, I've become distracted by the constant disk access and have been trying everything to eliminate it before proceeding with the rest of the build - nogo. Your post gave me the clue - boot with Sil3114 disabled = no disk activity; boot with enabled = constant disk flogging.
I've got the Sil driver up to 1.2.3.1 but no better. Suspect it may be the Sil3114 BIOS that needs upgrading but seems no way to flash it - have you got anywhere with your debugging?
Appreciate a solution before I go crazy with the tick, tick tick....

Firewire/1394 devices are not auto-detected with k8n neo4 platinum

I am unable to detect firewire/1394 devices to my PC through my K8N Neo4 Platinum. That is, I plug in the device through the firewire port and windows doesn't detect that a device has been plugged in.
I have tried:
-2 firewire devices, both are Canon digital camcorders (ZR10 and ZR25MC)
-2 different firewire cables
-reinstalling windows, got all windows updates except
(Microsoft Base Smart Card Cryptographic Service Provider Package: x86 (KB909520))
-patch from microsoft, discussed here
(https://forum-en.msi.com/index.php?topic=81749.0)
-both firewire devices using both cables connect just fine to a test computer
-both my computer and the test computer have Windows XP Pro SP2
Windows doesn't make the noise "bah-dum" that it has detected a device, nor does it display the dialog that gives me options of what programs to use. Once in a while, if I leave it connected for a while and come back, windows will eventually find it...or windows might bog down and get really slow. It speeds up again instantly once I unplug the firewire device. Strange, I know. Also there are NO conflicts in device manager.
Could it be?:
-bios misconfiguration
-need to use an older chipset driver (i am using most recent from nvidia.com)
-onboard audio or front audio needs to be disabled
-the k8n neo4 platinum simply has connection problems with some firewire devices
(i hope not)
Bob

Built2Last: (good questions!)
I tried your suggestion by removing PCI cards and made FURTHER progress. I found out that my firewire card, the Syba NEC1394-P3, has some compatibility issues with my other PCI cards. I found this out because:
1. it worked fine after I placed it in a non-comm (orange) slot and removed my soundcard (X-Fi) and Belkin wireless modem, and
2. a tech support representative from Syba told me that that particular firewire card has compatibility issues
Quote
Also, SD-NEC-4F is our older model firewire card.
Our new firewire card (SD-PCI-4F) is using VIA VT6306 chipset and no customer complain about any installation issue so far.
If the SD-NEC-4F still giving you trouble, I'll suggest you to return it and exchange for the SD-PCI-4F firewire card.
At least he is honest and wants to help, so I remain impartial towards Syba.
So I figured out the firewire card, but not the onboard firewire. Ok, but check this out! When the Syba card was working, I could plug in BOTH the external hard drive AND either of the Canon camcorders to the Syba firewire card. Windows all three devices just fine. Again, the onboard firewire would ONLY detect JUST the external hard drive, but would not detect either of the Canon camcorders. It seems as though the ball again is knocked back into MSI's court on this issue. Any ideas?
syar2003:
As for drivers, I checked for drivers for: onboard firewire, add-in firewire card, and Canon camcorders.
-I cannot find where there is an MSI firewire driver for my onboard firewire port. I originally guess that it was part of my chipset driver installer, but the README doesn't say anything about it. It is also not an additional download on MSI's website. But since it detects an external hard drive I figure I must already have it.
-The add-in firewire card does not have drivers. I repeat, they do not exist. The manual and Syba's website both state that drivers for the card are included all versions of Windows back to Windows 98.
-Canon's website has a driver/software download page but it also appears that drivers do not exist for the Canon camcorders.
Yes the camcorder is set to VCR mode.
Yes the IEEE1394 is correctly installed, since external hard drive connects okay.
I tried two DV cables and both are connected fine.
The camcorders do not support USB as far as I can see, and if they do, I'm not using it.

XP64bit installation halts, K8N Neo4 Platinum - No SATA drives found?

Similar Messages

Maybe you are looking for