Xperia Z1 Firmware build 14.3.A.0.757

I have the Xperia Z1 Model number C6902, and still cannot get the latest firmware build 14.3.A.0.757 to fix al the problems of 14.3.A.0.681. Can anyone assist??? I am really getting tired of the sound and speaker issues. Will appreciate any comments.
Thks.,

after testing the new firmware on z1 c6903 the sound bug is gone and ui is little nice but other problems still excist the heating issue using app for 5 mins like facebook and watsapp but speacially the camera taking few pictures heats up the phone near camera area and drains battery
still not fixed stuff
1 heat issue(using apps for 5 min)
2 camera not on par with other devices(produces too grainy pictures on higher res like 15.5 and 20.7 mp mode )
3 battery drain using apps and camera not fix that much still dosent looks like a 3000 mah phone
if this issues are fixed for z1 it becomes the best phone ever so fix this sony plz

Similar Messages

Xperia Z2 Firmware Update via PC Companion = FAIL!

I appologize if this is a duplicate post. I searched the forum before posting but it seemed similar posts weren't exactly the same issue(s) I'm experiencing.
I'm getting the notification that there is a firmware update for my Xperia Z2 tablet but that I am required to use PC Companion to download/install it. However, for some reason PC Companion refuses to detect that my tablet is connected. I've tried multiple usb ports and two different computers. Under device manager it doesn't show any device driver issues and the usb drivers are installed and up-to-date. However I constantly run into error message after error message. The tablet is set to MTP mode and connected via the included Sony usb cable. I've followed every wizard, prompt, guide, etc. but in the end PC Companion still says there's no phone/tablet connected. Would be so much easier if it would just download the update to the tablet like EVERY other android device I own does.

Did you take a look at this?
http://talk.sonymobile.com/t5/FAQ/USB-connection-problems/m-p/348074#U348074
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien

New firmware build 4 out (FW_E3000_1.0.02.004_US_20100727_code)

will give it a try!
Last Release Date: Aug 6, 2010
Firmware version: 1.0.02 (build 04)
- Updated Parental Controls and Guest Access web login page
- Updated time zone
- Added web security warning page when wireless security has been disabled
- Added support of display language detection to web administration user interface
- Added support of WPA2 Enterprise and WPA Enterprise security methods
- Enhanced online surfing performance when Parental Controls has been enabled
- Fixed web user interface display issue in other languages
- Fixed some minor bugs
- Removed Logviewer IP Address feature

https://homesupport.cisco.com/en-us/wireless/linksys/E3000
Posted the link for easy reference.
The Search Function is your friend.... and Google too.
How to Secure your Network
How to Upgrade Routers Firmware
Setting-Up a Router with DSL Internet Service
Setting-Up a Router with Cable Internet Service
How to Hard Reset or 30/30/30 your Router

WRT54GX2 GPL Firmware building unsuccessful

Hi,
I downloaded WRT54GX2_v1.01.19.tar.gz from Linksys GPL repository and tried building an image on a debian system (Woody) but I keep running into build problem. Please see the error message below. Can someone from Linksys give me a recommended building platform to build these images? Also I noticed that you have removed the above file but the WRT54GX2_v1.01.14.tar.gz is even less build friendly because there is no make file or toolchain included. I just want to build a default image first before making any modification but so far no luck.
Any help is appreciated.
Thanks,
wadalada
       if egrep "^#define CONFIG_IMAGE_SQUASH 1" /home/wada/wrt/WRT54GX_ALL_Rea
ltek/linux-2.4.x/include/linux/autoconf.h > /dev/null; then\
       /home/wada/wrt/WRT54GX_ALL_Realtek/tools/mksquashfs /home/wada/wrt/WRT54
GX_ALL_Realtek/romfs /home/wada/wrt/WRT54GX_ALL_Realtek/images/2x2/cramfs.img -b
e -noappend;\
       fi;\
       /opt/toolchain_mips/bin/mips-linux-objcopy -S -O binary /home/wada/wrt/W
RT54GX_ALL_Realtek/linux-2.4.x/vmlinux /home/wada/wrt/WRT54GX_ALL_Realtek/images
/2x2/kernel.bin;\
       gzip -9f /home/wada/wrt/WRT54GX_ALL_Realtek/images/2x2/kernel.bin;\
       if [ "-" -lt 50 ] ;then\
               echo -e "\n\nError Kernel size is bigger than flash size of ker
nel";\
               echo -e "KERNEL size is Too Big Flash size only 0x100000\n\n";\
               exit 1;\
       fi;\
       /home/wada/wrt/WRT54GX_ALL_Realtek/tools/packbin /home/wada/wrt/WRT54GX
_ALL_Realtek/images/2x2/kernel.bin.gz r 0 /home/wada/wrt/WRT54GX_ALL_Realtek/ima
ges/2x2/kernel.bix;\
       /home/wada/wrt/WRT54GX_ALL_Realtek/tools/kfspad /home/wada/wrt/WRT54GX_
ALL_Realtek/images/2x2/kernel.bix 0x100000 /home/wada/wrt/WRT54GX_ALL_Realtek/i
mages/2x2/cramfs.img /home/wada/wrt/WRT54GX_ALL_Realtek/images/2x2/run_tmp.bin;\
       /home/wada/wrt/WRT54GX_ALL_Realtek/tools/packer /home/wada/wrt/WRT54GX_
ALL_Realtek/images/2x2/run.bin 0=/home/wada/wrt/WRT54GX_ALL_Realtek/images/2x2/r
un_tmp.bin,0,3e0000-18 0x3e1000-18=/home/wada/wrt/WRT54GX_ALL_Realtek/images/2x2
/run_tmp.bin,3e0000-18;\
       /home/wada/wrt/WRT54GX_ALL_Realtek/tools/packbin /home/wada/wrt/WRT54GX
_ALL_Realtek/images/2x2/run.bin k 0 /home/wada/wrt/WRT54GX_ALL_Realtek/images/2x
2/run.bix;\
       fi
/bin/sh: -c: line 9: syntax error near unexpected token `fi'
/bin/sh: -c: line 9: `fi;\'
make[2]: *** [image] Error 2
make[2]: Leaving directory `/home/wada/wrt/WRT54GX_ALL_Realtek/vendors/Realtek/RTL865XB'

Well...I've been hacking away at WRT54GX4 1.00.20, just out of curiosity, all evening...with no success: 1) Makefiles do not behave well on FC6, at a minimum 2) I cannot find a way to make images/2x28/kernel.bin.gz happen 3) copying vmlinux over to images (and gzipping it) doesn't seem to help much, although it gets past not having the kernel file of (2). 4) No load_srcroot directory anywhere, and no obvious way to produce what's needed there or in the images directory. ....I got pretty far up the creek (up to a point where Image Packer ran, but skipped packing a bunch of items that don't exist/build. I'm unsure how much of my lack of progress is (1) versus not having all the needed parts in the tar.gz), but I still have no paddle.

Xperia U Firmware or Roms for Locked Bootloader

Ics is very bad, I want to install any other custom firmware or rom on my phone, but is there any for locked Bootloader ?
Nothing is True, Everything is Permitted

I'm moving your thread to Android development. Hopefully you get some response there instead.
What are your thoughts about this forum? Let us know by doing this short survey.

Issues even after updating to build 14.3.A.0.757

List of problems that I am still facing with my Z1 Compact..
1. Walkman widget does not work in lockscreen 8 out of 10 times at least, if not more.
2. Notification sounds still cracks, though the ringer issue appears to be solved.
3. The back key never functions while "IN A CALL". Also, if I try to type something while "IN A CALL" the keyboard never appears no matter how many times I tap on the typing panel.
If this is the standard of your development, then, unfortunately, competing with the likes of IPHONE 5S shall always be a dream.
And as a consumer, spending 35K over a phone shall compel a user to atleast expect the basic functionalities to work properly.
But may be. SONY INDIA does not care about it's customers!! At least both the KITKAT 4.4.2 builds make me feel this.
I have always been a SONY ERICSSON/SONY user since 2004 but this phone is causing me **bleep** lot of troubles.
Guys, my post is sincerely directed towards SONY developers/testers/othersonyexecutives.
I am definitely looking forward to a reply from SONY regarding these above mentioned issues which still persist even after the second update.
P.S. Please do not ask me to repair using PCC or SUS. They didn't work. I cannot do them again and again!!

I have a black Xperia Z1 Compact with a build date of 14W04 (week 4 of 2014) which I have just updated for the first time since purchasing SIM-free from Phones4U, using Sony PC Companion on my Windows 7 PC, to Android 4.4.2 and Sony Software 14.3.A.0.757 and fortunately (and very untypically) I do not seem to have experienced any of the reported problems at all. I have just taken several flash photos in the pitch dark indoors using Superior Auto mode and I cannot identify any flash bleed or uneven flash illumination as reported in other topics and threads. I am really very surprised, because from my past experience with technology in general, if there is a possible potential technical problem around, I always seem to be one of the unlucky people who it affects! However, I do agree that the overall photo quality does not seem to be nearly as good as would be expected from the apparently impressive documented camera specification and is really quite dissapointing! I wondered if a third-party Android camera app would improve photographic performance, or if the obvious shortcomings are too deeply associated with the camera lens and/or the Sony firmware?

Xperia Z1 Compact D5503 14.3.A.0.757 upgrade experience

hi all,
I just want to share my experience with the latest build version 14.3.A.0.757 which has become available in Austria on Friday, 18th of April 2014.
Friday afternoon an OTU I installed the update to Android 4.4.2 which automatically was suggested once my phone learned about its availability.
the upgrade itself worked out fine and everythink seemed to work as it should. later in the evening I recognized, that the phone was unusually warm and that the power from battery quickly drained.
in addition the "Walkman" app didn't find any media - not from internal storage or from the SD card where my music was stored.
I started to investigate if this could be a common, already known issue and found out, that with 4.4.2 SD access has been changed by Google and that other users also have the problems with heating up devices and battery.
I tried to format my SD, because the app which used the battery at most was the "Mediaserver" app. even stopping this app manually didn't change anything. it seems this app kept my phone active all the time, which led to the battery drain.
I also resetted the device from the Settings menu several times, but nothing changed. finally a "Repair" via Sony Campanion software from my PC did the trick. my last resort would have been to downgrade to 4.3 which I could avoid, it seems so far. my phone now is acting as before and battery lifetime is back to normal.
unfortunately Sony takes several weeks to come up with OS upgrades in Austria and even than publishes a buggy version it seems.
I hope my posting could help to solve the issues for others who also faced them.
best regards
Mario

After upgrade to xxxxx757 build volume of the default ringtone named Xperia is decreased and battery drain bring

X4600m2 bios/ilom firmware upgrade problem

In the X4600m2 downloads, under Software 2.3, in the firmware category, I downloaded ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima (md5 checks out). I can't install the new firmware however (using the ILOM cli):
-> load -source tftp://172.22.95.215/ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima
NOTE: A firmware upgrade will cause the server and ILOM to
      be reset. It is recommended that a clean shutdown of
      the server be done prior to the upgrade procedure.
      An upgrade takes about 6 minutes to complete. ILOM
      will enter a special mode to load new firmware. No
      other tasks can be performed in ILOM until the
      firmware upgrade is complete and ILOM is reset.
Are you sure you want to load the specified file (y/n)? y
Do you want to preserve the configuration (y/n)? n
Image is not for this platform.
Firmware image update failed.
->With all previous releases this worked fine.
Update: the upgrade on the ILOM web interface also fails.
I'm running this version currently:
-> version
SP firmware 2.0.2.10
SP firmware build number: 38791
SP firmware date: Tue Nov 4 18:36:42 PST 2008
SP filesystem version: 0.1.14
Any idea why this is failing? I've tried both preserving and not preserving the configuration.
Edited by: kaufmann on Jul 22, 2009 9:27 AM

Quote from: renewest on 14-July-12, 19:43:52
Are you saying that it worked before because of an error? I've worked with boards before tha supported 2 monitors, 1 on the mainboard and 1 on a graphics card.
Quote from: renewest on 14-July-12, 19:43:52
Are you saying that it worked before because of an error?
Yes.. normally onboard become automatically disabled, when dedicated card is installed.

Cisco EPC3925 EuroDocsis Wifi turned off but light stays ON w/ recently updated firmware

hi there
i have a Cisco EPC3925 EuroDocsis 3.0 2-PORT Voice Gateway and i just noticed that today they pushed an OTA firmware upgrade via ISP "Melita" here in Malta.
It looks like now when i disable the wifi, the green led for wifi still stays on, did anybody notice this? I have this firmware now:
Model:
Cisco EPC3925
Vendor:
Cisco
Hardware Revision:
1.0
Serial Number:
MAC Address:
Bootloader Revision:
2.3.0_R1
Current Software Revision:
epc3925-ESIP-16-v302r125573-131025c-l2gre
Firmware Name:
epc3925-ESIP-16-v302r125573-131025c-l2gre.bin
Firmware Build Time:
Oct 25 11:30:50 2013
Cable Modem Status:
Operational
Wireless Network:
Disable
if anyone has a link to a newer or older firmware, i'd like to change this one, we don't normally use wifi and prefer the cable. I checked with inSSIDer 3 and when the wifi is disabled it cannot be found but i am really thinking if that's for real since the light is still on....
any help appreciated..
thanks
Gabrio

hello everyone,
The technical supoort of my ISP got back to me with the following:
The fact that the Wi-Fi light on your Melita cisco modem is still switched on is because we have recently launched the new Melita Wi-Fi, where all Melita’s cisco modems are being used to broadcast this signal so that customers with Melita mobile can connect to Wi-Fi wherever they are. The cisco modem is being used only as a repeater to boost this signal and it will not affect at any time the connection that Melita is providing you.
Having said that this option may be switched off by turning the modem to bridge mode, by doing this you will eliminate completely the Wi-Fi option from your modem. If you wish to turn your modem to bridge mode kindly follow the link below to guide you through the process.
http://help.melita.com/index.php/bridge-modestatic-ip/
so anyone else that wants to do the same, feel free using that guide.
One piece of advice.... if you don't plan in using another wifi router to plug to the CISCO, should you want to have the wifi again, then you need to log to http://192.168.100.1 and then switch back to "router" mode from "bridge" mode. DHCP will not work in bridge mode so if you just turn on wifi, you will have to manually configure it. Or switch back to "router" for the time being.
When you enable bridge mode, you cannot log to http://192.168.0.1 maybe obvious but good to know.
I have to say that this ISP pushed this OTA update without saying anything to its customers for boosting their signal to their mobile customers, very nasty indeed. I don't like to have the wifi on at home when nobody uses it, it's bad for the health, it made both me and my wife having headaches in the past, so if i need it, i turn it on, otherwise it's OFF and i want to have the freedom of doing that at my will.
There's already too many microwaves and wifis out there, at least at home i want to control it!.

New WRT-160 V2 firmware posted

New WRT-160N V2 firmware (build 15) is posted.
http://www.linksysbycisco.com/US/en/support/WRT160N/download
I have had it up (as a beta) for three week, no problems
I used Firefox to install / flash instead of Safari///

when you connect your com to the modem the speed got to be faster
because your are getting direct connection with the modem.
when you use the router the speed gets slow because it handles multiple devices at the same time
however as you mentioned that it is reducing your speed to 1-2meg download and 1 meg upload.
that seems to be really bad .try to hard reset the router for 1 minute then reconfigure your router from the scratch
after that upgrade the firmware on the router and power cycle the entire network.and set the wireless security as WPA2 personal that would give you good speed on the wireless computers. also try to reduced the MTU to 1364....
once you are done with these troubleshooting then you would Definitely get the better speed .

[REPORT/HELP] ideapad K1 build K1_A301_02_02_110822_SG a lot problem...

Hi, last two weeks ago I was brought a K1 from Singapore IT Fair @ Suntec City. It come with original firmware build 725 SG version and it generate a lot of problem to me.
1. Random reboot very unstable 4 ~ 5 times per day!
2. Can't wake up from sleep mode, it show black screen at all and the Home button two LED light up.
3. The LED Screen will bright up from sleep after a moment and it will never turn off the screen again unleast you touch the power button...
4. Use a lot of battery power even in sleep mode... I was managed to turn off wifi and left it in sleep mode overnight, the next day the pad totally left 3% battery power and unable to boot up...
After one week, I was received the firmware update notification, it push the firmware to K1_A301_02_02_110822_SG version. I was think about Lenovo Software Development team have release a bug free firmware to resolve this kind of problem... but after upgraded the latest firmware, it was generated more problem to me.
The new problem was found here...
1. Random system reboot... (Still got this problem but least happen {1 time reboot per day} after firmware updated to build 110822_SG, I was confirmed it's not apps compatibility problem, even use the Youtube to play online stream video, the system screen also black up and reboot...)
2. Can't wake up from sleep mode! OMG, still got this problem... I was tried to change to AWD Launcher EX to reduce this case happen, and the pad running more smooth than stock launcher.
3. After upgrade firmware, It prompt up a lot of apps error! I was do factory reset, and all back to normal. But it also prompt up error message at home screen. I was suspect internal service error because after firmware upgrading, I can't sync my browser bookmark with Google Chrome account... And the google calander sync also not working anymore... (Bookmark and Calander won't sync!)
4. Battery power fast finish and the pad will generate heat even sleep mode! (Suspect wifi problem, even at sleep never automatic turn off)
5. The LED Screen will bright up from sleep after a moment and it will never turn off the screen again unleast you touch the power button... (Problem with stock launcher, replace with AWD launcher EX resloved)
6. After firmware upgrade, Wifi signal become weak... (Suspect driver problem, and I hear that got a lot of bug at wifi driver!)
OMG... What a buggy tablet pad??? I brought it bring to work, now nothing can do... Just leave it at home... everyday I have check with system update, and I never receive new system firmware since last week build K1_A301_02_02_110822_SG. I was disappointed about Lenovo Software Development team can't resolve the problem in short time when problem found... Most the bad thing is consumer can't get the good after-sell product support... Hopefully Lenovo Software Development team able to release the new firmware and resolve the problem. Thank...

hey all,
thank you for the information.
i have passed this to the engineers for them to check.
WW Social Media
Important Note: If you need help, post your question in the forum, and include your system type, model number and OS. Do not post your serial number.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
Follow @LenovoForums on Twitter!
Have you checked out the Community Knowledgebase yet?!
How to send a private message? --> Check out this article.

Can't update E61 (prod code 0538289) to firmware v...

Hi,
I've been trying to update my E61 phone (prod code 0538289) to the latest v3 firmware build for over 3 weeks now.
The phone came factory flashed with firmware v2 and would like to take advantage of the enhanced SIP capabilities present in v3.
At first NSU game me a message that no update is available but I can reflash to the same version. After several attempts all I get is that no updates are available.
Can anyone help?
Thanks,
VladS

Check here: http://europe.nokia.com/A4305060
For your product code there is no update available. Generally, you can only update phones which are not branded by a provider. I guess you bought a branded phone from a phone company. You have to go to your phone company to have the firmware updated. Branding and support for the branded firmware is generally from the company you got the phone from. Nokia Service Centers in your country may also have the branded firmwares for your provider.

Does the RV180 support DHCPv6-PD with firmware 1.0.3.10?

Hello-
I am running a SOHO on Comcast and wish to get IPv6 working. I have read some old posts around the 'net stating that the Cisco RV180 does not support DHCPv6-PD, and that this is needed to successfully use IPv6 with Comcast. Firmware 1.0.3.10 was released in late July 2013. I don't see anything in the release notes stating that DHCPv6-PD support was added, so I suspect it was not. Can anyone confirm that it still does not? Does anyone know if it will be added in the near future (say 6 months?)
Thanks!

I can confirm that it does not. Been working with Tuska (from Comcast) on this for over a year and no word from Cisco on whether they plan to build the functionality into the next firmware build or not. Tuska has formally requested Cisco make this update. Very disappointed in the black hole that Cisco has allowed this to fall into. This is supposed to be a business product (why I purchased it), I expected more.
Just ordered a new router to replace my RV180 since I see no hope of Cisco getting it together. I think Cisco is more interested in supporting their large corporate accounts and have abandoned supporting SOHO (as evident with the sale of Linksys to Belkin).

Bluetooth problems with Xperia C4 - Android Wear - Motorola 360

Hello, I have a serious problem with my new Sony Xperia C4 Dual phone
I'm always losing the connection with my Motorola 360 smartwatch.The first time I start everything, I can pair my phone with my watch.
Everything is working fine (watchfaces, apps, notifications, etc).
But randomly (can be 1 hour or can be 1 day, when the phone is too far from the watch, after a phone restart, or ...) the Bluetooth connection is lost and will never come back.
If I could restart the connection that would not be that serious but... I can't!
Android Wear will then start hanging on "Connecting" state and it will not reconnnect until I completely restart the pairing process. The only way is to reconnect is :
1. Delete the watch in Motorola Connect
2. Delete the watch in Android Wear
3. Hard reset the watch (otherwise it's impossible to start the pairing process)
4. Turn off and turn on bluetooth on Xperia C4
5. Disconnect all other Bluetooth devices (like car audio and BSP10 Speaker)
6. Restart the pairing process
The whole process is taking about 15 minutes and 30% of the watch battery. (because every apps needs to be reinstalled) What I did so far and did not fix the random disconnection problem :
-Hard resetted 2 times the phone
-Hard resetted 4 times the watch (2x on 5.0 and 2x on 5.1 Android Wear)
-Restarted many times the phone
-Restarted many times the watch
-Tried with the "Sony Smart Connect App" disabled on the phone
-Tried without any extra app on the watch (uninstalled trackID or Sony Music, for example)
-Updated all the apps on the phone
-Tried with a "Blank" phone and "Blank" watch (did not install ANY application) What I can say :
-The problem occurs even in Android 5.0.2 or 5.1.1 on the watch (Motorola has just rolled out the 5.1.1 OTA)
-The problem occurs with different Moto 360 Watches (tried with the watch of a friend, same problems)
-The problem occurs only on the Xperia C4 (Dual) phone. (works great on a Zopo ZP999, Wiko Highway and Galaxy S3)
-Even after resetting, it is sometimes difficult to find the watch in the Bluetooth list, while every other phone can see the watch perfectly!
-Bluetooth hardware is working perfectly, because I can connect to my car, with my BSP10 speaker and another Bose SLIII Speaker. Additional information for the watch :Motorola 360 Watch Build LDZ220Android Wear 1.1.1.2006643Google Play Services 7.5.76 (2002306-534)Android Platform 5.1.1 Additional information for the phone :Android 5.0Model E5333 (Xperia C4 Dual)Build 27.1.B.1.81Smart Connect 5.7.18.401 (11 june 2015) What I think :
There is something that is preventing the watch from being connected properly in the Sony extra Apps.
I think the Smart Connect and Throw (and maybe other) extra apps are bringing a lot of trouble to the Bluetooth connection with the watch. Since 2 days, Motorola has just rolled out the 5.1.1 update of the Moto 360 watch, the update is now enabling WiFi.
I connected my watch to the wifi and the "Cloud sync" connection is working perfectly in Android Wear.
When there is no Wifi network, the phone/watch are trying to connect back with Bluetooth... and the problems can begin. Other problem : when the watch is connected to the phone, immediatly after making NFC contact with my Sony BSP10 speaker (to pair them), the connection is lost between the phone and the watch. So if I use my speaker i will have to hard reset my watch. In fact... every morning I take my watch and I need to start that f*c*in pairing process because of the software bug on the phone.Can somebody help here?
Is there any update planned? Thanks in advance, Guich

Hello Quester : Like I said, I tried with two different watches ( 2x moto 360) and the problem is still present.
So you can exclude there is something wrong with the watch.
I tried with 5.0.2 and 5.1.1 on the watch and it has no effect. My bluetooth hardware is working fine one the phone, too. (other devices are working, like speakers, car, laptop).So clearly, there is a SOFTWARE issue that drops the pairing and makes Android Wear losing the connection and never coming back. Yesterday everything was working fine until I used the BSP10 speaker, connection with the watch was lost.
I'm absolutely sure the problem is bound to Sony Smart Connect/Throw/whatever because on other phones it works perfectly!

Macbook EFI Firmware update 1.1

hi,
I don't know if anyone else is having this problem, software update has downloaded and installed the same update about 8 times now, each time it says the installation is sucessful.
Does anyone know if it's a problem my end or with the record of installations or anything else but it's starting to really bug me.
Thanks
Sam

sam-uk wrote:
hi,
I don't know if anyone else is having this problem, software update has downloaded and installed the same update about 8 times now, each time it says the installation is sucessful.
Does anyone know if it's a problem my end or with the record of installations or anything else but it's starting to really bug me.
Thanks
Sam
Supposedly the Software Update version is supposed put it in the /Applications/Utilities directory and run it automatically. There are additional steps needed to complete the firmware update. If you didn't do these things, it may attempt to reinstall the package until it senses the latest firmware build is installed. You might try downloading Firmware Update 1.2:
http://www.apple.com/support/downloads/macbookefifirmwareupdate12.html
It loads a program that you then need to run in order to update your firmware.
http://support.apple.com/kb/HT1557?viewlocale=en_US
4. Double-click the appropriate package for your computer to start the firmware update process. (The installer puts the Firmware Updater in the /Applications/Utilities folder, and launches it automatically.)
5. Read the onscreen instructions and click Shut Down to proceed with the update. The firmware image will be loaded on your machine, and your machine will shut down, but the update will not be installed until the next step.
6. Hold down the power button until the power indicator light flashes, then release it. A long tone will be heard, then a gray screen with an Apple logo appears. There is a progress bar under the logo. As the progress bar moves, your firmware is being updated.
Important: Do not unplug, shutdown, or restart your computer while the update is taking place. Interrupting a firmware update can render your computer unusable. If this happens, take your machine to an Apple store or authorized service provider or perform the recovery yourself using another Macintosh computer to download the Firmware Restoration CD disk image from http://www.apple.com/support/downloads/. This software allows you to create a CD which you can use to restore your machine to working order.
Installation takes a few minutes.
7. After your firmware has been updated, your machine will restart.
8. After you log in, a dialog box will appear indicating the firmware update has been successful. Click OK to dismiss this dialog.
I didn't quite figure out all these steps. You can manually run the Firmware Updater from the /Applications/Utilities directory.

Xperia Z1 Firmware build 14.3.A.0.757

Similar Messages

Maybe you are looking for