XPS 8700, GTX Titan x, Black Screen on Boot have bios A10

I have been trying to get this to work for a few days now. I contacted Nvidia support and they said the problem could be that this pcie slot defaults to 8x speed even though this slot is clearly a 16x. 
I have looked in the bios where the person at Nvidia suggested I could change the bus speed. Here is what they said below. 
"I found the same link to check on your motherboard specs. But I couldn't find if the PCI-e 3.0 running at 8x speed or 16x speed.
If it is running at 8x speed then, the issue could be possibly due to motherboard compatibility. Most of these motherboards are defaulted to 8x speed, even though the video card is connected in a 16x slot, there are options to change the slot speed in the BIOS.
Regards
NVIDIA Customer Care"
I just got a brand new Coolermaster V750 for this gfx card so I am sure I am getting enough power, and I added new 16gb gskill ram to it. I have more than enough to get this stuff up and running. I have even seen this was a common problem with the older bios and the 9 series late last year when they launched and people put them on these xps systems. The bios supposedly fixed it for the other people having problems with this but it would not fix the problem for me. You can see the thread in the link below.
en.community.dell.com/.../19601491

Anthony817
So in your humble opinion would you think that my Titan could be defective? 
I humbly do not know.  I've not heard anyone attempt a Titan in an XPS 8700.
You might ask for help on a hard-core forum like overclock.net
http://www.overclock.net/f/69/nvidia
good luck.
This thread lists what has been working...
http://en.community.dell.com/support-forums/desktop/f/3515/t/19611037

Similar Messages

  • Quad Channel RAM Black screen on boot

    So i can run my computer with Duo channel RAM DIMM slot 1 & 3, but if i add DIMM slot 5 & 7 my computer screen just stays black forever. the computer starts up and stays powered on, but no signal to screen. i have tried all 4 ram pieces alone in DIMM slot 1 and the computer boots just fine and it says 4gb ram in both BIOS and my computer properties. I have also tried just adding just one ram piece in DIMM slot 5 and the same problem occurs, just a black screen on boot.
    my specs are:
    MOBO:MSI X99S SLI PLUS, Socket-2011-3
    ATX, DDR4, 4xPCIe-x16, USB3.0, SLI/CFX, M.2
    CPU: Intel Core i7-5820K, Socket-LGA2011-3
    6-Core,3.3GHz,15MB,140W,22nm,28 PCIe lanes,Haswell
    RAM: HyperX Predator DDR4 2133MHz 16GB
    4x4GB, DDR4 Non-ECC CL13 DIMM (Kit of 4) XMP Preda
    GPU: MSI GeForce GTX 980 Gaming 4GB PhysX
    PSU: Cooler Master GX 750W PSU
    ATX 12V V2.31, 80 Plus Bronze, Standard, 4x 6+2pin
    I have Flashed the BIOS to 1.5, swapped around on the RAM pieces to no avail.

    Quote from: badboy2k on 24-December-14, 13:20:22
    some people are having problems with that board! (no idea what is going on with it)
    just for the sake of problem checking can you take out your CPU and look at the pins in the cpu socket with a bright light and a magnifier (check multiple angles) to see if any of the pins are bent?
    a few of the pins are indeed a little bent out of position, would it be best to return the board or should i be able to bend them back into the correct position?

  • MacBook Pro 17" late 2009 - Black screen on boot, not even a grey screen

    Got a monstrous problem.
    Started up my MacBook Pro (bought in Feb. This year, core 2 duo 2.88GHz/4 Gb RAM - basically the top specced model.)
    Booted up today, no grey start-up screen. No screen at all. Yet I can still log into Snow Leopard, but again no screen. Rebooted into boot camp, heard windows start. Managed to log in again no screen. Volume controls, keyboard illumination work. Just a black screen.
    I have tried resetting PRAM, etc. with no success. Cannot use hardware test as the screen simply does not start.
    Any ideas before I throw the effing thing from a 5th floor window in frustration?
    Is this the Nvidia problem other folk have experienced?
    I am tempted to ask for a new machine spending 2 months on and off with my previous MacBook Pro in and out of repair if this is a hardware problem that has been fixed in recent Macs.
    Regards,
    J

    I had the same problem just now. My 15" MBP (6.2). I followed the following steps and it worked for me. I used another Mac in my house to use screen sharing to accomplish these things:
    1) access the /private/var/vm/ directory on the nonworking computer from the working computer. This is invisble so you will have to press cmdshiftg in the finder and go to /volumes/YOURHARDDISKNAME/private/var/vm to get there or use an application that lets you view invisble folders like PathFinder.
    2) delete the sleepimage file
    3) delete the /system/library/extensions.mkext file
    4) eject the drive (drag to the trash)
    5) press the power button to turn off the non working computer
    6) turn the nonworking computer back on normally(cross your fingers) then if it works,
    7) open up the the terminal.app in /applications/utilities
    8) type sudo pmset -a hibernatemode 0
    9) make sure there is no sleepimage file again
    That worked for me...hope it helps for you!

  • Update kernel to 3.17 - Black screen under booting

    Hi,
    I update kernel from 3.16 to 3.17, and when I start booting, see log an after a certain time I get black screen.
    I have notebook Asus X200M with intel graphic card.
    Booting log:
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.16.1-1-ARCH (nobody@var-lib-archbuild-testing-x86_64-tobias) (gcc version 4.9.1 (GCC) ) #1 SMP PREEMPT Thu Aug 14 07:40:19 CEST 2014
    [ 0.000000] Command line: initrd=\EFI\archiso\archiso.img archisobasedir=arch archisolabel=ARCH_201409
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009dfff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000200fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000020100000-0x00000000b8d36fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000b8d37000-0x00000000b8d66fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000b8d67000-0x00000000b8eb6fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000b8eb7000-0x00000000b93b9fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000b93ba000-0x00000000b9bacfff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000b9bad000-0x00000000b9badfff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000b9bae000-0x00000000b9beffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000b9bf0000-0x00000000b9d65fff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000b9d66000-0x00000000b9ff9fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000b9ffa000-0x00000000b9ffffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fffffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] e820: update [mem 0xa9461018-0xa9471057] usable ==> usable
    [ 0.000000] extended physical RAM map:
    [ 0.000000] reserve setup_data: [mem 0x0000000000000000-0x000000000008efff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x0000000000090000-0x000000000009dfff] usable
    [ 0.000000] reserve setup_data: [mem 0x000000000009e000-0x000000000009ffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000000100000-0x000000001fffffff] usable
    [ 0.000000] reserve setup_data: [mem 0x0000000020000000-0x00000000200fffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000020100000-0x00000000a9461017] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000a9461018-0x00000000a9471057] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000a9471058-0x00000000b8d36fff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000b8d37000-0x00000000b8d66fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000b8d67000-0x00000000b8eb6fff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000b8eb7000-0x00000000b93b9fff] ACPI NVS
    [ 0.000000] reserve setup_data: [mem 0x00000000b93ba000-0x00000000b9bacfff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000b9bad000-0x00000000b9badfff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000b9bae000-0x00000000b9beffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000b9bf0000-0x00000000b9d65fff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000b9d66000-0x00000000b9ff9fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000b9ffa000-0x00000000b9ffffff] usable
    [ 0.000000] reserve setup_data: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
    [ 0.000000] reserve setup_data: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
    [ 0.000000] reserve setup_data: [mem 0x0000000100000000-0x000000013fffffff] usable
    [ 0.000000] efi: EFI v2.31 by American Megatrends
    [ 0.000000] efi: ACPI=0xb93a4000 ACPI 2.0=0xb93a4000 SMBIOS=0xb9a96e18
    [ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x0000000000001000) (0MB)
    [ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000001000-0x0000000000007000) (0MB)
    [ 0.000000] efi: mem02: type=7, attr=0xf, range=[0x0000000000007000-0x000000000008f000) (0MB)
    [ 0.000000] efi: mem03: type=10, attr=0xf, range=[0x000000000008f000-0x0000000000090000) (0MB)
    [ 0.000000] efi: mem04: type=7, attr=0xf, range=[0x0000000000090000-0x000000000009e000) (0MB)
    [ 0.000000] efi: mem05: type=0, attr=0xf, range=[0x000000000009e000-0x00000000000a0000) (0MB)
    [ 0.000000] efi: mem06: type=7, attr=0xf, range=[0x0000000000100000-0x0000000001000000) (15MB)
    [ 0.000000] efi: mem07: type=2, attr=0xf, range=[0x0000000001000000-0x0000000001f47000) (15MB)
    [ 0.000000] efi: mem08: type=7, attr=0xf, range=[0x0000000001f47000-0x0000000020000000) (480MB)
    [ 0.000000] efi: mem09: type=0, attr=0xf, range=[0x0000000020000000-0x0000000020100000) (1MB)
    [ 0.000000] efi: mem10: type=7, attr=0xf, range=[0x0000000020100000-0x000000007ec2e000) (1515MB)
    [ 0.000000] efi: mem11: type=2, attr=0xf, range=[0x000000007ec2e000-0x0000000080000000) (19MB)
    [ 0.000000] efi: mem12: type=7, attr=0xf, range=[0x0000000080000000-0x000000009a000000) (416MB)
    [ 0.000000] efi: mem13: type=4, attr=0xf, range=[0x000000009a000000-0x000000009a020000) (0MB)
    [ 0.000000] efi: mem14: type=7, attr=0xf, range=[0x000000009a020000-0x00000000a9461000) (244MB)
    [ 0.000000] efi: mem15: type=2, attr=0xf, range=[0x00000000a9461000-0x00000000a9472000) (0MB)
    [ 0.000000] efi: mem16: type=1, attr=0xf, range=[0x00000000a9472000-0x00000000aa3b9000) (15MB)
    [ 0.000000] efi: mem17: type=2, attr=0xf, range=[0x00000000aa3b9000-0x00000000aa3bc000) (0MB)
    [ 0.000000] efi: mem18: type=1, attr=0xf, range=[0x00000000aa3bc000-0x00000000aa3d3000) (0MB)
    [ 0.000000] efi: mem19: type=2, attr=0xf, range=[0x00000000aa3d3000-0x00000000aa3d5000) (0MB)
    [ 0.000000] efi: mem20: type=1, attr=0xf, range=[0x00000000aa3d5000-0x00000000aa3f0000) (0MB)
    [ 0.000000] efi: mem21: type=4, attr=0xf, range=[0x00000000aa3f0000-0x00000000b8737000) (227MB)
    [ 0.000000] efi: mem22: type=7, attr=0xf, range=[0x00000000b8737000-0x00000000b8af2000) (3MB)
    [ 0.000000] efi: mem23: type=3, attr=0xf, range=[0x00000000b8af2000-0x00000000b8d37000) (2MB)
    [ 0.000000] efi: mem24: type=0, attr=0xf, range=[0x00000000b8d37000-0x00000000b8d67000) (0MB)
    [ 0.000000] efi: mem25: type=7, attr=0xf, range=[0x00000000b8d67000-0x00000000b8eb7000) (1MB)
    [ 0.000000] efi: mem26: type=10, attr=0xf, range=[0x00000000b8eb7000-0x00000000b93ba000) (5MB)
    [ 0.000000] efi: mem27: type=6, attr=0x800000000000000f, range=[0x00000000b93ba000-0x00000000b9b4c000) (7MB)
    [ 0.000000] efi: mem28: type=5, attr=0x800000000000000f, range=[0x00000000b9b4c000-0x00000000b9bad000) (0MB)
    [ 0.000000] efi: mem29: type=4, attr=0xf, range=[0x00000000b9bad000-0x00000000b9bae000) (0MB)
    [ 0.000000] efi: mem30: type=6, attr=0x800000000000000f, range=[0x00000000b9bae000-0x00000000b9bf0000) (0MB)
    [ 0.000000] efi: mem31: type=4, attr=0xf, range=[0x00000000b9bf0000-0x00000000b9d66000) (1MB)
    [ 0.000000] efi: mem32: type=6, attr=0x800000000000000f, range=[0x00000000b9d66000-0x00000000b9ffa000) (2MB)
    [ 0.000000] efi: mem33: type=4, attr=0xf, range=[0x00000000b9ffa000-0x00000000ba000000) (0MB)
    [ 0.000000] efi: mem34: type=7, attr=0xf, range=[0x0000000100000000-0x0000000140000000) (1024MB)
    [ 0.000000] efi: mem35: type=11, attr=0x8000000000000000, range=[0x00000000e00f8000-0x00000000e00f9000) (0MB)
    [ 0.000000] efi: mem36: type=11, attr=0x8000000000000000, range=[0x00000000fed01000-0x00000000fed02000) (0MB)
    [ 0.000000] efi: mem37: type=11, attr=0x8000000000000000, range=[0x00000000ffc00000-0x0000000100000000) (4MB)
    [ 0.000000] SMBIOS 2.8 present.
    [ 0.000000] DMI: ASUSTeK COMPUTER INC. X200MA/X200MA, BIOS X200MA.404 04/04/2014
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x140000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 000000000 mask F80000000 write-back
    [ 0.000000] 1 base 080000000 mask FC0000000 write-back
    [ 0.000000] 2 base 0BA000000 mask FFE000000 uncachable
    [ 0.000000] 3 base 0BC000000 mask FFC000000 uncachable
    [ 0.000000] 4 base 100000000 mask FC0000000 write-back
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xba000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xba000 max_arch_pfn = 0x400000000
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b23000, 0x01b23fff] PGTABLE
    [ 0.000000] BRK [0x01b24000, 0x01b24fff] PGTABLE
    [ 0.000000] BRK [0x01b25000, 0x01b25fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13fe00000-0x13fffffff]
    [ 0.000000] [mem 0x13fe00000-0x13fffffff] page 2M
    [ 0.000000] BRK [0x01b26000, 0x01b26fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13c000000-0x13fdfffff]
    [ 0.000000] [mem 0x13c000000-0x13fdfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x13bffffff]
    [ 0.000000] [mem 0x100000000-0x13bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0x1fffffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0x1fffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x20100000-0xb8d36fff]
    [ 0.000000] [mem 0x20100000-0x201fffff] page 4k
    [ 0.000000] [mem 0x20200000-0xb8bfffff] page 2M
    [ 0.000000] [mem 0xb8c00000-0xb8d36fff] page 4k
    [ 0.000000] BRK [0x01b27000, 0x01b27fff] PGTABLE
    [ 0.000000] BRK [0x01b28000, 0x01b28fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0xb8d67000-0xb8eb6fff]
    [ 0.000000] [mem 0xb8d67000-0xb8eb6fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xb9bad000-0xb9badfff]
    [ 0.000000] [mem 0xb9bad000-0xb9badfff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xb9bf0000-0xb9d65fff]
    [ 0.000000] [mem 0xb9bf0000-0xb9d65fff] page 4k
    [ 0.000000] init_memory_mapping: [mem 0xb9ffa000-0xb9ffffff]
    [ 0.000000] [mem 0xb9ffa000-0xb9ffffff] page 4k
    [ 0.000000] RAMDISK: [mem 0x7ec2e000-0x7fffffff]
    [ 0.000000] ACPI: Early table checksum verification disabled
    [ 0.000000] ACPI: RSDP 0x00000000B93A4000 000024 (v02 _ASUS_)
    [ 0.000000] ACPI: XSDT 0x00000000B93A4080 00008C (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: FACP 0x00000000B93B5EE0 00010C (v05 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 128/32 (20140424/tbfadt-618)
    [ 0.000000] ACPI: DSDT 0x00000000B93A41A0 011D3A (v02 _ASUS_ Notebook 01072009 INTL 20120913)
    [ 0.000000] ACPI: FACS 0x00000000B93B9F80 000040
    [ 0.000000] ACPI: APIC 0x00000000B93B5FF0 000084 (v03 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: FPDT 0x00000000B93B6078 000044 (v01 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: MCFG 0x00000000B93B60C0 00003C (v01 _ASUS_ Notebook 01072009 MSFT 00000097)
    [ 0.000000] ACPI: LPIT 0x00000000B93B6100 000104 (v01 _ASUS_ Notebook 00000003 VLV2 0100000D)
    [ 0.000000] ACPI: ECDT 0x00000000B93B6208 0000C1 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
    [ 0.000000] ACPI: HPET 0x00000000B93B62D0 000038 (v01 _ASUS_ Notebook 01072009 AMI. 00000005)
    [ 0.000000] ACPI: SSDT 0x00000000B93B6308 000763 (v01 PmRef CpuPm 00003000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 0x00000000B93B6A70 000290 (v01 PmRef Cpu0Tst 00003000 INTL 20061109)
    [ 0.000000] ACPI: SSDT 0x00000000B93B6D00 00017A (v01 PmRef ApTst 00003000 INTL 20061109)
    [ 0.000000] ACPI: UEFI 0x00000000B93B6E80 000042 (v01 _ASUS_ Notebook 00000000 00000000)
    [ 0.000000] ACPI: BGRT 0x00000000B93B6EC8 000038 (v00 _ASUS_ Notebook 01072009 AMI 00010013)
    [ 0.000000] ACPI: MSDM 0x00000000B8D64F98 000055 (v03 _ASUS_ Notebook 00000000 ASUS 00000001)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000013fffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
    [ 0.000000] NODE_DATA [mem 0x13fff5000-0x13fff9fff]
    [ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b600000-ffff88013f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x13fffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0008efff]
    [ 0.000000] node 0: [mem 0x00090000-0x0009dfff]
    [ 0.000000] node 0: [mem 0x00100000-0x1fffffff]
    [ 0.000000] node 0: [mem 0x20100000-0xb8d36fff]
    [ 0.000000] node 0: [mem 0xb8d67000-0xb8eb6fff]
    [ 0.000000] node 0: [mem 0xb9bad000-0xb9badfff]
    [ 0.000000] node 0: [mem 0xb9bf0000-0xb9d65fff]
    [ 0.000000] node 0: [mem 0xb9ffa000-0xb9ffffff]
    [ 0.000000] node 0: [mem 0x100000000-0x13fffffff]
    [ 0.000000] On node 0 totalpages: 1019552
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3996 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 11773 pages used for memmap
    [ 0.000000] DMA32 zone: 753412 pages, LIFO batch:31
    [ 0.000000] Normal zone: 4096 pages used for memmap
    [ 0.000000] Normal zone: 262144 pages, LIFO batch:31
    [ 0.000000] x86/hpet: Will disable the HPET for this platform because it's not reliable
    [ 0.000000] Reserving Intel graphics stolen memory at 0xbb000000-0xbeffffff
    [ 0.000000] ACPI: PM-Timer IO Port: 0x408
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x06] enabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] res edge lint[0x51])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] res res lint[0xaa])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0xa3])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] dfl dfl lint[0x70])
    [ 0.000000] ACPI: NMI not connected to LINT 1!
    [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-86
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 103
    [ 0.000000] PM: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x20000000-0x200fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xa9461000-0xa9461fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xa9471000-0xa9471fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xb8d37000-0xb8d66fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xb8eb7000-0xb93b9fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xb93ba000-0xb9bacfff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xb9bae000-0xb9beffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xb9d66000-0xb9ff9fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xba000000-0xbaffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbb000000-0xbeffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbf000000-0xe00f7fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe00f8000-0xe00f8fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe00f9000-0xfed00fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed01000-0xfed01fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfed02000-0xffbfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
    [ 0.000000] e820: [mem 0xbf000000-0xe00f7fff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88013fc00000 s86784 r8192 d23808 u524288
    [ 0.000000] pcpu-alloc: s86784 r8192 d23808 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1003598
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: initrd=\EFI\archiso\archiso.img archisobasedir=arch archisolabel=ARCH_201409
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] AGP: Checking aperture...
    [ 0.000000] AGP: No AGP bridge found
    [ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
    [ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
    [ 0.000000] Memory: 3677272K/4078208K available (5334K kernel code, 887K rwdata, 1688K rodata, 1128K init, 1164K bss, 400936K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
    [ 0.000000] NR_IRQS:8448 nr_irqs:1024 16
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] Maximum core-clock to bus-clock ratio: 0x1a
    [ 0.000000] Resolved frequency ID: 0, frequency: 83200 KHz
    [ 0.000000] TSC runs at 2163200 KHz
    [ 0.000000] lapic_timer_frequency = 277333
    [ 0.000000] tsc: Detected 2163.200 MHz processor
    [ 0.000039] Calibrating delay loop (skipped), value calculated using timer frequency.. 4328.66 BogoMIPS (lpj=7210666)
    [ 0.000044] pid_max: default: 32768 minimum: 301
    [ 0.000061] ACPI: Core revision 20140424
    [ 0.029799] ACPI: All ACPI Tables successfully acquired
    [ 0.031844] Security Framework initialized
    [ 0.031853] Yama: becoming mindful.
    [ 0.032325] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.034100] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.034885] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.034901] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
    [ 0.035292] Initializing cgroup subsys memory
    [ 0.035333] Initializing cgroup subsys devices
    [ 0.035346] Initializing cgroup subsys freezer
    [ 0.035352] Initializing cgroup subsys net_cls
    [ 0.035360] Initializing cgroup subsys blkio
    [ 0.035395] CPU: Physical Processor ID: 0
    [ 0.035398] CPU: Processor Core ID: 0
    [ 0.035404] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
    ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
    [ 0.040179] mce: CPU supports 6 MCE banks
    [ 0.040190] CPU0: Thermal monitoring enabled (TM1)
    [ 0.040199] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
    Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
    tlb_flushall_shift: 6
    [ 0.040321] Freeing SMP alternatives memory: 20K (ffffffff819f9000 - ffffffff819fe000)
    [ 0.054319] ftrace: allocating 20434 entries in 80 pages
    [ 0.065409] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
    [ 0.098392] smpboot: CPU0: Intel(R) Pentium(R) CPU N3520 @ 2.16GHz (fam: 06, model: 37, stepping: 03)
    [ 0.098419] TSC deadline timer enabled
    [ 0.098452] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, full-width counters, Intel PMU driver.
    [ 0.098468] ... version: 3
    [ 0.098470] ... bit width: 40
    [ 0.098472] ... generic registers: 2
    [ 0.098474] ... value mask: 000000ffffffffff
    [ 0.098476] ... max period: 000000ffffffffff
    [ 0.098478] ... fixed-purpose events: 3
    [ 0.098480] ... event mask: 0000000700000003
    [ 0.121896] x86: Booting SMP configuration:
    [ 0.121902] .... node #0, CPUs: #1
    [ 0.139857] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.143193] #2 #3
    [ 0.182296] x86: Booted up 1 node, 4 CPUs
    [ 0.182302] smpboot: Total of 4 processors activated (17312.66 BogoMIPS)
    [ 0.183192] devtmpfs: initialized
    [ 0.189816] PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
    [ 0.189820] PM: Registering ACPI NVS region [mem 0xb8eb7000-0xb93b9fff] (5255168 bytes)
    [ 0.191745] pinctrl core: initialized pinctrl subsystem
    [ 0.191811] RTC time: 20:42:53, date: 10/31/14
    [ 0.191901] NET: Registered protocol family 16
    [ 0.192122] cpuidle: using governor ladder
    [ 0.192127] cpuidle: using governor menu
    [ 0.192195] ACPI: bus type PCI registered
    [ 0.192199] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.192351] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.192356] PCI: not using MMCONFIG
    [ 0.192358] PCI: Using configuration type 1 for base access
    [ 0.209690] ACPI: Added _OSI(Module Device)
    [ 0.209695] ACPI: Added _OSI(Processor Device)
    [ 0.209697] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.209700] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.213766] ACPI : EC: EC description table is found, configuring boot EC
    [ 0.235995] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
    [ 0.261579] ACPI: Dynamic OEM Table Load:
    [ 0.261590] ACPI: SSDT 0xFFFF880139648800 00045B (v01 PmRef Cpu0Ist 00003000 INTL 20061109)
    [ 0.262859] ACPI: Dynamic OEM Table Load:
    [ 0.262869] ACPI: SSDT 0xFFFF880139649000 000433 (v01 PmRef Cpu0Cst 00003001 INTL 20061109)
    [ 0.286101] ACPI: Dynamic OEM Table Load:
    [ 0.286109] ACPI: SSDT 0xFFFF880139ACB200 00015F (v01 PmRef ApIst 00003000 INTL 20061109)
    [ 0.295812] ACPI: Dynamic OEM Table Load:
    [ 0.295821] ACPI: SSDT 0xFFFF8801396240C0 00008D (v01 PmRef ApCst 00003000 INTL 20061109)
    [ 0.310441] ACPI: Interpreter enabled
    [ 0.310454] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S1_] (20140424/hwxface-580)
    [ 0.310463] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20140424/hwxface-580)
    [ 0.310489] ACPI: (supports S0 S3 S4 S5)
    [ 0.310493] ACPI: Using IOAPIC for interrupt routing
    [ 0.310534] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.311446] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
    [ 0.312163] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.321942] ACPI: Power Resource [USBC] (on)
    [ 0.330436] ACPI: Power Resource [PLPE] (on)
    [ 0.330733] ACPI: Power Resource [PLPE] (on)
    [ 0.335104] ACPI: Power Resource [CLK0] (on)
    [ 0.335182] ACPI: Power Resource [CLK1] (on)
    [ 0.338894] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.338905] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
    [ 0.338985] \_SB_.PCI0:_OSC invalid UUID
    [ 0.338989] _OSC request data:1 1f 0
    [ 0.338996] acpi PNP0A08:00: _OSC failed (AE_ERROR); disabling ASPM
    [ 0.339862] PCI host bridge to bus 0000:00
    [ 0.339868] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.339872] pci_bus 0000:00: root bus resource [io 0x0000-0x006f]
    [ 0.339876] pci_bus 0000:00: root bus resource [io 0x0078-0x0cf7]
    [ 0.339879] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.339883] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.339887] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
    [ 0.339890] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000fffff]
    [ 0.339894] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xd0815ffe]
    [ 0.339906] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
    [ 0.340095] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
    [ 0.340112] pci 0000:00:02.0: reg 0x10: [mem 0xd0000000-0xd03fffff]
    [ 0.340124] pci 0000:00:02.0: reg 0x18: [mem 0xc0000000-0xcfffffff pref]
    [ 0.340136] pci 0000:00:02.0: reg 0x20: [io 0xf080-0xf087]
    [ 0.340329] pci 0000:00:13.0: [8086:0f23] type 00 class 0x010601
    [ 0.340352] pci 0000:00:13.0: reg 0x10: [io 0xf070-0xf077]
    [ 0.340363] pci 0000:00:13.0: reg 0x14: [io 0xf060-0xf063]
    [ 0.340374] pci 0000:00:13.0: reg 0x18: [io 0xf050-0xf057]
    [ 0.340384] pci 0000:00:13.0: reg 0x1c: [io 0xf040-0xf043]
    [ 0.340395] pci 0000:00:13.0: reg 0x20: [io 0xf020-0xf03f]
    [ 0.340405] pci 0000:00:13.0: reg 0x24: [mem 0xd0815000-0xd08157ff]
    [ 0.340454] pci 0000:00:13.0: PME# supported from D3hot
    [ 0.340613] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
    [ 0.340635] pci 0000:00:14.0: reg 0x10: [mem 0xd0800000-0xd080ffff 64bit]
    [ 0.340695] pci 0000:00:14.0: PME# supported from D3hot D3cold
    [ 0.340814] pci 0000:00:14.0: System wakeup disabled by ACPI
    [ 0.340900] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
    [ 0.340929] pci 0000:00:1a.0: reg 0x10: [mem 0xd0500000-0xd05fffff]
    [ 0.340944] pci 0000:00:1a.0: reg 0x14: [mem 0xd0400000-0xd04fffff]
    [ 0.341048] pci 0000:00:1a.0: PME# supported from D0 D3hot
    [ 0.341212] pci 0000:00:1b.0: [8086:0f04] type 00 class 0x040300
    [ 0.341238] pci 0000:00:1b.0: reg 0x10: [mem 0xd0810000-0xd0813fff 64bit]
    [ 0.341311] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
    [ 0.341467] pci 0000:00:1c.0: [8086:0f48] type 01 class 0x060400
    [ 0.341532] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
    [ 0.341633] pci 0000:00:1c.0: System wakeup disabled by ACPI
    [ 0.341704] pci 0000:00:1c.1: [8086:0f4a] type 01 class 0x060400
    [ 0.341768] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
    [ 0.341865] pci 0000:00:1c.1: System wakeup disabled by ACPI
    [ 0.341939] pci 0000:00:1c.3: [8086:0f4e] type 01 class 0x060400
    [ 0.342003] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
    [ 0.342100] pci 0000:00:1c.3: System wakeup disabled by ACPI
    [ 0.342181] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
    [ 0.342411] pci 0000:00:1f.3: [8086:0f12] type 00 class 0x0c0500
    [ 0.342448] pci 0000:00:1f.3: reg 0x10: [mem 0xd0814000-0xd081401f]
    [ 0.342521] pci 0000:00:1f.3: reg 0x20: [io 0xf000-0xf01f]
    [ 0.342839] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.342968] pci 0000:02:00.0: [168c:0036] type 00 class 0x028000
    [ 0.342996] pci 0000:02:00.0: reg 0x10: [mem 0xd0700000-0xd077ffff 64bit]
    [ 0.343047] pci 0000:02:00.0: reg 0x30: [mem 0xd0780000-0xd078ffff pref]
    [ 0.343115] pci 0000:02:00.0: supports D1 D2
    [ 0.343119] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.343175] pci 0000:02:00.0: System wakeup disabled by ACPI
    [ 0.349069] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.349077] pci 0000:00:1c.1: bridge window [mem 0xd0700000-0xd07fffff]
    [ 0.349202] pci 0000:03:00.0: [10ec:5286] type 00 class 0xff0000
    [ 0.349225] pci 0000:03:00.0: reg 0x10: [mem 0xd0600000-0xd060ffff]
    [ 0.349361] pci 0000:03:00.0: supports D1 D2
    [ 0.349365] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
    [ 0.349427] pci 0000:03:00.0: System wakeup disabled by ACPI
    [ 0.349509] pci 0000:03:00.2: [10ec:8136] type 00 class 0x020000
    [ 0.349532] pci 0000:03:00.2: reg 0x10: [io 0xe000-0xe0ff]
    [ 0.349561] pci 0000:03:00.2: reg 0x18: [mem 0xd0614000-0xd0614fff 64bit]
    [ 0.349580] pci 0000:03:00.2: reg 0x20: [mem 0xd0610000-0xd0613fff 64bit pref]
    [ 0.349661] pci 0000:03:00.2: supports D1 D2
    [ 0.349665] pci 0000:03:00.2: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.355738] pci 0000:00:1c.3: PCI bridge to [bus 03]
    [ 0.355744] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
    [ 0.355750] pci 0000:00:1c.3: bridge window [mem 0xd0600000-0xd06fffff]
    [ 0.356698] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12) *0, disabled.
    [ 0.356818] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.356935] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.357050] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.357165] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.357280] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.357396] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.357512] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 12) *0, disabled.
    [ 0.359318] ACPI: Enabled 4 GPEs in block 00 to 3F
    [ 0.359471] ACPI : EC: GPE = 0x18, I/O: command/status = 0x66, data = 0x62
    [ 0.359689] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.359696] vgaarb: loaded
    [ 0.359698] vgaarb: bridge control possible 0000:00:02.0
    [ 0.359824] PCI: Using ACPI for IRQ routing
    [ 0.365679] PCI: pci_cache_line_size set to 64 bytes
    [ 0.365734] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
    [ 0.365738] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
    [ 0.365740] e820: reserve RAM buffer [mem 0xa9461018-0xabffffff]
    [ 0.365743] e820: reserve RAM buffer [mem 0xb8d37000-0xbbffffff]
    [ 0.365746] e820: reserve RAM buffer [mem 0xb8eb7000-0xbbffffff]
    [ 0.365749] e820: reserve RAM buffer [mem 0xb9bae000-0xbbffffff]
    [ 0.365752] e820: reserve RAM buffer [mem 0xb9d66000-0xbbffffff]
    [ 0.365755] e820: reserve RAM buffer [mem 0xba000000-0xbbffffff]
    [ 0.365940] NetLabel: Initializing
    [ 0.365943] NetLabel: domain hash size = 128
    [ 0.365945] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.365968] NetLabel: unlabeled traffic allowed by default
    [ 0.366034] Switched to clocksource refined-jiffies
    [ 0.374184] pnp: PnP ACPI init
    [ 0.374218] ACPI: bus type PNP registered
    [ 0.374302] pnp 00:00: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.374554] system 00:01: [io 0x0680-0x069f] has been reserved
    [ 0.374560] system 00:01: [io 0x0400-0x047f] has been reserved
    [ 0.374564] system 00:01: [io 0x0500-0x05fe] has been reserved
    [ 0.374568] system 00:01: [io 0x0600-0x061f] has been reserved
    [ 0.374573] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.374688] system 00:02: [io 0x03f8-0x0411] could not be reserved
    [ 0.374694] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.374837] pnp 00:03: Plug and Play ACPI device, IDs FLT0102 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
    [ 0.374933] pnp 00:04: Plug and Play ACPI device, IDs ATK3001 PNP030b (active)
    [ 0.375354] system 00:05: [mem 0xe0000000-0xefffffff] could not be reserved
    [ 0.375359] system 00:05: [mem 0xfed01000-0xfed01fff] has been reserved
    [ 0.375364] system 00:05: [mem 0xfed03000-0xfed03fff] has been reserved
    [ 0.375368] system 00:05: [mem 0xfed04000-0xfed04fff] has been reserved
    [ 0.375372] system 00:05: [mem 0xfed0c000-0xfed0ffff] has been reserved
    [ 0.375376] system 00:05: [mem 0xfed08000-0xfed08fff] has been reserved
    [ 0.375380] system 00:05: [mem 0xfed1c000-0xfed1cfff] has been reserved
    [ 0.375384] system 00:05: [mem 0xfee00000-0xfeefffff] has been reserved
    [ 0.375388] system 00:05: [mem 0xfef00000-0xfeffffff] has been reserved
    [ 0.375394] system 00:05: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.376886] pnp: PnP ACPI: found 6 devices
    [ 0.376889] ACPI: bus type PNP unregistered
    [ 0.385464] Switched to clocksource acpi_pm
    [ 0.385504] pci 0000:00:1c.0: PCI bridge to [bus 01]
    [ 0.385518] pci 0000:00:1c.1: PCI bridge to [bus 02]
    [ 0.385524] pci 0000:00:1c.1: bridge window [mem 0xd0700000-0xd07fffff]
    [ 0.385533] pci 0000:00:1c.3: PCI bridge to [bus 03]
    [ 0.385537] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
    [ 0.385543] pci 0000:00:1c.3: bridge window [mem 0xd0600000-0xd06fffff]
    [ 0.385552] pci_bus 0000:00: resource 4 [io 0x0000-0x006f]
    [ 0.385556] pci_bus 0000:00: resource 5 [io 0x0078-0x0cf7]
    [ 0.385559] pci_bus 0000:00: resource 6 [io 0x0d00-0xffff]
    [ 0.385563] pci_bus 0000:00: resource 7 [mem 0x000a0000-0x000bffff]
    [ 0.385566] pci_bus 0000:00: resource 8 [mem 0x000c0000-0x000dffff]
    [ 0.385570] pci_bus 0000:00: resource 9 [mem 0x000e0000-0x000fffff]
    [ 0.385574] pci_bus 0000:00: resource 10 [mem 0xc0000000-0xd0815ffe]
    [ 0.385578] pci_bus 0000:02: resource 1 [mem 0xd0700000-0xd07fffff]
    [ 0.385582] pci_bus 0000:03: resource 0 [io 0xe000-0xefff]
    [ 0.385585] pci_bus 0000:03: resource 1 [mem 0xd0600000-0xd06fffff]
    [ 0.385634] NET: Registered protocol family 2
    [ 0.386034] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
    [ 0.386172] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.386319] TCP: Hash tables configured (established 32768 bind 32768)
    [ 0.386368] TCP: reno registered
    [ 0.386384] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.386423] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.386554] NET: Registered protocol family 1
    [ 0.386582] pci 0000:00:02.0: Boot video device
    [ 0.386878] PCI: CLS 64 bytes, default 64
    [ 0.386971] Unpacking initramfs...
    [ 3.798196] Freeing initrd memory: 20296K (ffff88007ec2e000 - ffff880080000000)
    [ 3.798214] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
    [ 3.798219] software IO TLB [mem 0xa5461000-0xa9461000] (64MB) mapped at [ffff8800a5461000-ffff8800a9460fff]
    [ 3.798657] Scanning for low memory corruption every 60 seconds
    [ 3.799231] futex hash table entries: 1024 (order: 4, 65536 bytes)
    [ 3.799830] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 3.802497] zbud: loaded
    [ 3.802768] VFS: Disk quotas dquot_6.5.2
    [ 3.802834] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 3.803065] msgmni has been set to 7684
    [ 3.803159] Key type big_key registered
    [ 3.803575] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 3.803705] io scheduler noop registered
    [ 3.803711] io scheduler deadline registered
    [ 3.803804] io scheduler cfq registered (default)
    [ 3.804386] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 3.804416] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 3.804493] efifb: probing for efifb
    [ 3.804515] efifb: framebuffer at 0xc0000000, mapped to 0xffffc90010780000, using 1876k, total 1875k
    [ 3.804518] efifb: mode is 800x600x32, linelength=3200, pages=1
    [ 3.804520] efifb: scrolling: redraw
    [ 3.804523] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 3.807600] Console: switching to colour frame buffer device 100x37
    [ 3.810507] fb0: EFI VGA frame buffer device
    [ 3.810524] intel_idle: MWAIT substates: 0x33000020
    [ 3.810527] intel_idle: v0.4 model 0x37
    [ 3.810529] intel_idle: lapic_timer_reliable_states 0xffffffff
    [ 3.810913] GHES: HEST is not enabled!
    [ 3.811063] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 3.831365] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
    [ 3.832332] hpet: number irqs doesn't agree with number of timers
    [ 3.832373] Linux agpgart interface v0.103
    [ 3.832472] rtc_cmos 00:00: RTC can wake from S4
    [ 3.832710] rtc_cmos 00:00: rtc core: registered rtc_cmos as rtc0
    [ 3.832742] rtc_cmos 00:00: alarms up to one month, y3k, 242 bytes nvram
    [ 3.832763] Intel P-state driver initializing.
    [ 3.832782] Intel pstate controlling: cpu 0
    [ 3.832876] Intel pstate controlling: cpu 1
    [ 3.832970] Intel pstate controlling: cpu 2
    [ 3.833076] Intel pstate controlling: cpu 3
    [ 3.833279] ledtrig-cpu: registered to indicate activity on CPUs
    [ 3.833991] TCP: cubic registered
    [ 3.834789] NET: Registered protocol family 10
    [ 3.835678] NET: Registered protocol family 17
    [ 3.837271] registered taskstats version 1
    [ 3.839828] Magic number: 2:163:752
    [ 3.839841] tty ttyS3: hash matches
    [ 3.840028] rtc_cmos 00:00: setting system clock to 2014-10-31 20:42:56 UTC (1414788176)
    [ 3.840203] PM: Hibernation image not present or could not be loaded.
    [ 3.842178] Freeing unused kernel memory: 1128K (ffffffff818df000 - ffffffff819f9000)
    [ 3.842183] Write protecting the kernel read-only data: 8192k
    [ 3.846670] Freeing unused kernel memory: 800K (ffff880001538000 - ffff880001600000)
    [ 3.848729] Freeing unused kernel memory: 360K (ffff8800017a6000 - ffff880001800000)
    [ 3.865722] random: systemd-tmpfile urandom read with 1 bits of entropy available
    [ 3.868883] systemd-udevd[58]: starting version 216
    [ 3.887455] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
    [ 3.887463] ACPI: Power Button [PWRB]
    [ 3.887570] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
    [ 3.888627] ACPI: Lid Switch [LID]
    [ 3.888729] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
    [ 3.888734] ACPI: Sleep Button [SLPB]
    [ 3.888823] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    [ 3.888827] ACPI: Power Button [PWRF]
    [ 3.892296] sdhci: Secure Digital Host Controller Interface driver
    [ 3.892301] sdhci: Copyright(c) Pierre Ossman
    [ 3.902568] i8042: PNP: PS/2 Controller [PNP030b:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
    [ 3.905559] i8042: Detected active multiplexing controller, rev 1.1
    [ 3.906663] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 3.906689] serio: i8042 AUX0 port at 0x60,0x64 irq 12
    [ 3.906694] serio: i8042 AUX1 port at 0x60,0x64 irq 12
    [ 3.906698] serio: i8042 AUX2 port at 0x60,0x64 irq 12
    [ 3.906701] serio: i8042 AUX3 port at 0x60,0x64 irq 12
    [ 3.914328] wmi: Mapper loaded
    [ 3.918784] ACPI: bus type USB registered
    [ 3.918835] usbcore: registered new interface driver usbfs
    [ 3.918867] usbcore: registered new interface driver hub
    [ 3.918875] rtsx_pci 0000:03:00.0: irq 103 for MSI/MSI-X
    [ 3.918901] rtsx_pci 0000:03:00.0: rtsx_pci_acquire_irq: pcr->msi_en = 1, pci->irq = 103
    [ 3.918953] usbcore: registered new device driver usb
    [ 3.919389] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
    [ 3.919409] r8169 0000:03:00.2: can't disable ASPM; OS doesn't have ASPM control
    [ 3.919726] r8169 0000:03:00.2: irq 104 for MSI/MSI-X
    [ 3.920037] r8169 0000:03:00.2 eth0: RTL8402 at 0xffffc9000064c000, 10:c3:7b:66:32:b5, XID 04000800 IRQ 104
    [ 3.920547] SCSI subsystem initialized
    [ 3.921052] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 3.921071] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
    [ 3.921487] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
    [ 3.921518] xhci_hcd 0000:00:14.0: irq 105 for MSI/MSI-X
    [ 3.921976] hub 1-0:1.0: USB hub found
    [ 3.921995] hub 1-0:1.0: 6 ports detected
    [ 3.923415] xhci_hcd 0000:00:14.0: xHCI Host Controller
    [ 3.923425] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
    [ 3.923770] hub 2-0:1.0: USB hub found
    [ 3.923785] hub 2-0:1.0: 1 port detected
    [ 3.925827] libata version 3.00 loaded.
    [ 3.927536] ahci 0000:00:13.0: version 3.0
    [ 3.927753] ahci 0000:00:13.0: irq 106 for MSI/MSI-X
    [ 3.927966] [drm] Initialized drm 1.1.0 20060810
    [ 3.938420] ahci 0000:00:13.0: AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x1 impl SATA mode
    [ 3.938428] ahci 0000:00:13.0: flags: 64bit ncq pm led clo pio slum part deso sadm apst
    [ 3.939052] scsi0 : ahci
    [ 3.939333] scsi1 : ahci
    [ 3.939427] ata1: SATA max UDMA/133 abar m2048@0xd0815000 port 0xd0815100 irq 106
    [ 3.939430] ata2: DUMMY
    [ 3.940211] [drm] Memory usable by graphics device = 2048M
    [ 3.940216] [drm] Replacing VGA console driver
    [ 3.940221] checking generic (c0000000 1d5000) vs hw (c0000000 10000000)
    [ 3.940224] fb: switching to inteldrmfb from EFI VGA
    [ 3.940252] Console: switching to colour dummy device 80x25
    [ 3.945163] i915 0000:00:02.0: irq 107 for MSI/MSI-X
    [ 3.945177] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [ 3.945180] [drm] Driver supports precise vblank timestamp query.
    [ 3.986231] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
    [ 4.178812] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
    [ 4.265360] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 4.282149] ata1.00: ATA-8: KINGSTON SV300S37A120G, 525ABBF0, max UDMA/133
    [ 4.282170] usb 1-3: new high-speed USB device number 2 using xhci_hcd
    [ 4.282186] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 4.301865] ata1.00: configured for UDMA/133
    [ 4.302143] scsi 0:0:0:0: Direct-Access ATA KINGSTON SV300S3 BBF0 PQ: 0 ANSI: 5
    [ 4.305528] [drm] VBT doesn't support DRRS
    [ 4.313905] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
    [ 4.314705] sd 0:0:0:0: [sda] Write Protect is off
    [ 4.314710] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 4.314769] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 4.318558] sda: sda1 sda2 sda3 sda4 sda5
    [ 4.319762] sd 0:0:0:0: [sda] Attached SCSI disk
    [ 4.352944] fbcon: inteldrmfb (fb0) is primary device
    [ 4.656003] usb 1-4: new high-speed USB device number 3 using xhci_hcd
    [ 4.802506] tsc: Refined TSC clocksource calibration: 2166.666 MHz
    [ 4.833949] hub 1-4:1.0: USB hub found
    [ 4.834515] hub 1-4:1.0: 3 ports detected
    [ 4.836858] usb: failed to peer 1-4-port1 and usb2-port1 by location (1-4-port1:none) (usb2-port1:usb1-port1)
    [ 4.836867] usb 1-4-port1: failed to peer to usb2-port1 (-16)
    [ 4.836870] usb: port power management may be unreliable
    [ 4.838038] usb: failed to peer 1-4-port2 and usb2-port1 by location (1-4-port2:none) (usb2-port1:usb1-port1)
    [ 4.838047] usb 1-4-port2: failed to peer to usb2-port1 (-16)
    [ 4.839283] usb: failed to peer 1-4-port3 and usb2-port1 by location (1-4-port3:none) (usb2-port1:usb1-port1)
    [ 4.839292] usb 1-4-port3: failed to peer to usb2-port1 (-16)
    [ 5.106630] usb 1-4.1: new full-speed USB device number 4 using xhci_hcd
    [ 5.260234] usb 1-4.2: new high-speed USB device number 5 using xhci_hcd
    [ 5.352708] usb-storage 1-4.2:1.0: USB Mass Storage device detected
    [ 5.354630] scsi2 : usb-storage 1-4.2:1.0
    [ 5.355157] usbcore: registered new interface driver usb-storage
    [ 5.358066] usbcore: registered new interface driver uas
    [ 5.804227] Switched to clocksource tsc
    [ 5.996975] Console: switching to colour frame buffer device 170x48
    [ 6.023343] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 6.023358] i915 0000:00:02.0: registered panic notifier
    [ 6.092491] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
    [ 6.127628] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input9
    [ 6.127865] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
    [ 6.347180] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
    [ 6.358480] scsi 2:0:0:0: Direct-Access SanDisk Cruzer Blade 8.02 PQ: 0 ANSI: 0 CCS
    [ 6.360601] sd 2:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB)
    [ 6.361027] sd 2:0:0:0: [sdb] Write Protect is off
    [ 6.361050] sd 2:0:0:0: [sdb] Mode Sense: 45 00 00 08
    [ 6.361491] sd 2:0:0:0: [sdb] No Caching mode page found
    [ 6.361741] sd 2:0:0:0: [sdb] Assuming drive cache: write through
    [ 6.370486] sdb: sdb1 sdb2
    [ 6.374072] sd 2:0:0:0: [sdb] Attached SCSI removable disk
    [ 6.585273] ISO 9660 Extensions: RRIP_1991A
    [ 6.604648] loop: module loaded
    [ 6.669200] squashfs: version 4.0 (2009/01/31) Phillip Lougher
    [ 6.699504] device-mapper: uevent: version 1.0.3
    [ 6.699820] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: [email protected]
    [ 6.761101] EXT4-fs (dm-0): mounted filesystem without journal. Opts: (null)
    [ 7.249501] efivars: duplicate variable: AcpiGlobalVariable-c020489e-6db2-4ef2-9aa5-ca06fc11d36a
    [ 7.261555] systemd[1]: systemd 216 running in system mode. (+PAM -AUDIT -SELINUX -IMA -APPARMOR +SMACK -SYSVINIT +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID -ELFUTILS +KMOD -IDN )
    [ 7.262617] systemd[1]: Detected architecture 'x86-64'.
    [ 7.301337] systemd[1]: Set hostname to <archiso>.
    [ 7.301524] systemd[1]: Initializing machine ID from random generator.
    [ 7.625350] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 7.625510] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 7.625540] systemd[1]: Starting Remote File Systems.
    [ 7.625765] systemd[1]: Reached target Remote File Systems.
    [ 7.625796] systemd[1]: Starting Encrypted Volumes.
    [ 7.625970] systemd[1]: Reached target Encrypted Volumes.
    [ 7.626024] systemd[1]: Starting Dispatch Password Requests to Console Directory Watch.
    [ 7.626109] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
    [ 7.626135] systemd[1]: Starting Paths.
    [ 7.626295] systemd[1]: Reached target Paths.
    [ 7.626380] systemd[1]: Starting Arbitrary Executable File Formats File System Automount Point.
    [ 7.626764] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
    [ 7.626798] systemd[1]: Starting Swap.
    [ 7.626957] systemd[1]: Reached target Swap.
    [ 7.626985] systemd[1]: Starting Root Slice.
    [ 7.647934] systemd[1]: Created slice Root Slice.
    [ 7.647965] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 7.648331] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 7.648355] systemd[1]: Starting Delayed Shutdown Socket.
    [ 7.648535] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 7.648558] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 7.648749] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 7.648771] systemd[1]: Starting Journal Socket (/dev/log).
    [ 7.648960] systemd[1]: Listening on Journal Socket (/dev/log).
    [ 7.648983] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 7.649165] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 7.649199] systemd[1]: Starting udev Kernel Socket.
    [ 7.649365] systemd[1]: Listening on udev Kernel Socket.
    [ 7.649397] systemd[1]: Starting udev Control Socket.
    [ 7.649567] systemd[1]: Listening on udev Control Socket.
    [ 7.649590] systemd[1]: Starting User and Session Slice.
    [ 7.650145] systemd[1]: Created slice User and Session Slice.
    [ 7.650179] systemd[1]: Starting Journal Socket.
    [ 7.650370] systemd[1]: Listening on Journal Socket.
    [ 7.650417] systemd[1]: Starting System Slice.
    [ 7.650925] systemd[1]: Created slice System Slice.
    [ 7.662478] systemd[1]: Started Set Up Additional Binary Formats.
    [ 7.662529] systemd[1]: Mounting Huge Pages File System...
    [ 7.663922] systemd[1]: Starting Load Kernel Modules...
    [ 7.665094] systemd[1]: Starting udev Coldplug all Devices...
    [ 7.666141] systemd[1]: Starting Setup Virtual Console...
    [ 7.667202] systemd[1]: Mounting POSIX Message Queue File System...
    [ 7.738374] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 7.740716] systemd[1]: Mounting Debug File System...
    [ 7.742925] systemd[1]: Starting system-getty.slice.
    [ 7.744791] systemd[1]: Created slice system-getty.slice.
    [ 7.744825] systemd[1]: Starting Journal Service...
    [ 7.748641] systemd[1]: Started Journal Service.
    [ 8.073656] random: nonblocking pool is initialized
    [ 8.186980] FS-Cache: Loaded
    [ 8.258509] RPC: Registered named UNIX socket transport module.
    [ 8.258516] RPC: Registered udp transport module.
    [ 8.258546] RPC: Registered tcp transport module.
    [ 8.258551] RPC: Registered tcp NFSv4.1 backchannel transport module.
    [ 8.451188] FS-Cache: Netfs 'nfs' registered for caching
    [ 8.753221] systemd-journald[175]: Received request to flush runtime journal from PID 1
    [ 9.115001] systemd-udevd[213]: starting version 216
    [ 9.796902] ACPI: AC Adapter [AC0] (on-line)
    [ 9.883837] hidraw: raw HID events driver (C) Jiri Kosina
    [ 9.889691] ACPI: Battery Slot [BAT0] (battery present)
    [ 9.891267] thermal LNXTHERM:00: registered as thermal_zone0
    [ 9.891268] ACPI: Thermal Zone [THRM] (0 C)
    [ 9.963438] ACPI Warning: SystemIO range 0x000000000000f000-0x000000000000f01f conflicts with OpRegion 0x000000000000f000-0x000000000000f00f (\_SB_.PCI0.SBUS.SMBI) (20140424/utaddress-258)
    [ 9.963449] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 9.964519] mei_txe 0000:00:1a.0: can't derive routing for PCI INT A
    [ 9.964525] mei_txe 0000:00:1a.0: PCI INT A: no GSI
    [ 9.964590] mei_txe 0000:00:1a.0: irq 108 for MSI/MSI-X
    [ 10.141120] input: PC Speaker as /devices/platform/pcspkr/input/input10
    [ 10.174886] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 10.200306] systemd-udevd[228]: renamed network interface eth0 to enp3s0f2
    [ 10.241618] media: Linux media interface: v0.10
    [ 10.242057] microcode: CPU0 sig=0x30673, pf=0x8, revision=0x320
    [ 10.332225] systemd-journald[175]: Received request to flush runtime journal from PID 1
    [ 10.340831] Linux video capture interface: v2.00
    [ 10.356019] iTCO_vendor_support: vendor-support=0
    [ 10.405092] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
    [ 10.405174] iTCO_wdt: Found a Bay Trail SoC TCO device (Version=3, TCOBASE=0x0460)
    [ 10.405434] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
    [ 10.422683] microcode: CPU1 sig=0x30673, pf=0x8, revision=0x320
    [ 10.422740] microcode: CPU2 sig=0x30673, pf=0x8, revision=0x320
    [ 10.422840] microcode: CPU3 sig=0x30673, pf=0x8, revision=0x320
    [ 10.422970] microcode: Microcode Update Driver: v2.00 <[email protected]>, Peter Oruba
    [ 10.429277] Bluetooth: Core ver 2.19
    [ 10.429308] NET: Registered protocol family 31
    [ 10.429311] Bluetooth: HCI device and connection manager initialized
    [ 10.429322] Bluetooth: HCI socket layer initialized
    [ 10.429326] Bluetooth: L2CAP socket layer initialized
    [ 10.429339] Bluetooth: SCO socket layer initialized
    [ 10.545328] asus_wmi: ASUS WMI generic driver loaded
    [ 10.555713] usbcore: registered new interface driver btusb
    [ 10.568780] asus_wmi: Initialization: 0x1
    [ 10.568880] asus_wmi: BIOS WMI version: 7.9
    [ 10.568996] asus_wmi: SFUN value: 0x4a0877
    [ 10.571556] input: Asus WMI hotkeys as /devices/platform/asus-nb-wmi/input/input15
    [ 10.607024] asus_wmi: Backlight controlled by ACPI video driver
    [ 10.619927] cfg80211: Calling CRDA to update world regulatory domain
    [ 10.620046] uvcvideo: Found UVC 1.00 device USB2.0 HD UVC WebCam (04f2:b424)
    [ 10.621588] input: USB2.0 HD UVC WebCam as /devices/pci0000:00/0000:00:14.0/usb1/1-3/1-3:1.0/input/input16
    [ 10.621725] usbcore: registered new interface driver uvcvideo
    [ 10.621728] USB Video Class driver (1.1.1)
    [ 10.623479] snd_hda_intel 0000:00:1b.0: irq 109 for MSI/MSI-X
    [ 10.829115] sound hdaudioC0D0: autoconfig: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
    [ 10.829123] sound hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
    [ 10.829126] sound hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
    [ 10.829129] sound hdaudioC0D0: mono: mono_out=0x0
    [ 10.829132] sound hdaudioC0D0: inputs:
    [ 10.829136] sound hdaudioC0D0: Mic=0x1b
    [ 10.912319] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input17
    [ 10.912449] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input18
    [ 10.929663] intel_soc_dts_thermal: request_threaded_irq ret -22
    [ 10.938823] ath: phy0: WB335 2-ANT card detected
    [ 10.938829] ath: phy0: Set BT/WLAN RX diversity capability
    [ 10.947885] cfg80211: World regulatory domain updated:
    [ 10.947892] cfg80211: DFS Master region: unset
    [ 10.947894] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    [ 10.947898] cfg80211: (2402000 KHz - 2472000 KHz @ 0 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.947901] cfg80211: (2457000 KHz - 2482000 KHz @ 0 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.947904] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.947907] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.947910] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 10.947913] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 10.947915] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
    [ 10.947918] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
    [ 10.948016] ath: phy0: Enable LNA combining
    [ 10.949134] ath: phy0: ASPM enabled: 0x42
    [ 10.949138] ath: EEPROM regdomain: 0x60
    [ 10.949139] ath: EEPROM indicates we should expect a direct regpair map
    [ 10.949143] ath: Country alpha2 being used: 00
    [ 10.949145] ath: Regpair used: 0x60
    [ 10.949212] intel_rapl: RAPL domain uncore detection failed
    [ 10.949220] intel_rapl: RAPL domain dram detection failed
    [ 11.012452] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
    [ 11.012826] ieee80211 phy0: Atheros AR9565 Rev:1 mem=0xffffc90022480000, irq=17
    [ 11.038314] systemd-udevd[216]: renamed network interface wlan0 to wlp2s0
    [ 12.184211] r8169 0000:03:00.2 enp3s0f2: link down
    [ 12.184241] r8169 0000:03:00.2 enp3s0f2: link down
    [ 12.184263] IPv6: ADDRCONF(NETDEV_UP): enp3s0f2: link is not ready
    [ 13.309766] input: PS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio4/input/input14
    [ 13.313404] mousedev: PS/2 mouse device common for all mice
    [ 13.775732] r8169 0000:03:00.2 enp3s0f2: link up
    [ 13.775767] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0f2: link becomes ready
    [ 173.542337] EXT4-fs (sda5): recovery complete
    [ 173.545042] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null)
    It seems that after this line screen turn off:
    fb: switching to inteldrmfb from EFI VGA
    Last edited by peer (2014-10-31 20:50:24)

    Potomac wrote:
    check these bugreports :
    https://bugs.archlinux.org/task/42505
    https://bugs.archlinux.org/task/42353
    it seems that this bug related to i915 chip ( or intel graphic card ) is fixed in kernel 3.18rc3 mainline ( we can find this kernel package in AUR )
    there is also another and complete different bug when we use a kernel 3.17 and even 3.18 ( it's a random bug ) but with a similar effect : boot can hang ( the boot process suddenly stops ) :
    https://bbs.archlinux.org/viewtopic.php?id=189622
    https://bbs.archlinux.org/viewtopic.php?id=189324
    downgrading to kernel 3.16.x is the workaround
    I assume my computer is affected by one of these bugs. While I can get to the point where my window manager is loaded, everything almost immediately hangs (but doesn't freeze). Terminal windows become non-responsive and Chromium will refuse input. It's very weird. This happens with both of the 3.17 kernel updates but not in any of the 3.16 releases (including 3.16.7).
    This is on an AMD system (cpu/gpu w/ open source driver). Overall 3.17 seems rather buggy.

  • When I mirror my late 2012 mac mini to my apple tv. I only see a black screen.  I have no problems if I use my mid 2012 MBPr

    When I try to mirror my late 2012 macmini to my apple tv. I only see a black screen.  I have no problems if I use my mid 2012 MBPr.
    The mac mini is still on mavericks at present any advice welcome please.  (There is no other monitor attached to the macmini would this be an issue?)
    I use share screen to monitor my macmini from my MBPr
    Thank you
    Ken

    I have solve this problem.
    I plug in a usb 3.0 HDMI blackmagic capture device in to the mac mini and connected the HDMI out of the macmini to the HDMI in of the black magic.
    So it thinks it has a primary screen and it now mirror this the apple tv.

  • I am having trouble running videos through Safari but not Google Chrome.  All I get is a black screen.  I have the latest adobe flash update and have enabled plug ins.  any suggestions?

    I am having trouble running videos through Safari but not Google Chrome.  All I get is a black screen.  I have the latest adobe flash update and have enabled plug ins.  any suggestions?

    Open System Preferences > Flash Player then select the Advanced tab.
    Click Delete All under Browsing Data and Settings
    Not empty the Safari cache.
    From your Safari menu bar click Safari > Preferences then select the Advanced tab.
    Select:  Show Develop menu in menu bar
    Now click Develop from the menu bar. From the drop down menu click Empty Caches.
    Now try a video.

  • 970 GAMING black screen when boot on cold start, have to clear CMOS everytime

    I have 970 GAMING w/ FX8320, it shows black screen when boot on cold start, have to clear CMOS everytime to enter default.
    I have updated it to the up to date M11 bios. Once it boot up, it functions OK no matter whether you reboot or reset it. But after turned off a few hours (cooled down), it shows on black screen again on boot, all LED lights up OK, but I can hear the fan like keep rebooting, any idea?
    PSU seasonic 430W, GPU HD7750.

    In what DIMM slots did you insert your memory?  I just got and at this moment building a new computer with a 970. 
    A horrible experience I had with my last build reminded me of it.  My board was am MSI A88XM-E45.  DIMM1 is blue, DIMM2 is black, DIMM3 is blue, & DIMM4 is black.  When using two sticks of RAM, it says to install one on DIMM1 & the other in DIMM3 (Makes sense... After all, it's color colored that way).
    Well it would not boot.  I reseated every component and for HOURS tried almost everything.  Finally I decided to place my two sticks of RAM in the first two DIMMS and viola!
    I think I will begin this build the same way.

  • Black screen on boot & Diagnostic errors

    Hi, 
    I've a HP g62 notebook pc that has some problems when is booting.
    Sometimes the screen is black when i try to boot or i've a BSOD related with the atikmpag.sys.This PC doesn't have warranty, but i don't know if the problem is only because of the SO or if there is any hardware failure.
    The PC model is the: g62-b10sp. Product id XF293EA#AB9
    System ID 143A
    I tried the HP diagnostics wich I retrieved the some test menssages: Memory Test: PASSED
    SMART CHECK : PASSED
    Short DST : PASSED
    Optimized DST : PASSEDHard disk test: PASSED
    Battery Test : Primary - Replace
    Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 Start-Up Test : FAILED
    Failure ID: MBQ3W8-5667NG-9XL03F-X0F403 Run-In Test: FAILED
    FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403 System Tuneup: FAILED
    FAILURE ID: MBQ3W8-5667NG-9XL03F-C0F403 
    Someone from the HP support team could help me? 
    I wanna know what those failures id are related... They are failures from motherboard/graphics?
    Thank you for you attention
    Best regards

      Hi , Thank you for visiting the HP Forums! A great place where you can find solutions for your issues, with help from the community!
    I came across your post about the Notebook, and wanted to assist you! I have looked into your issue about your HP G62-b10SP Notebook and an Black screen on boot showing. Thank you for the error messages and the explanation. Very helpful in diagnosing the issue. The first error Battery Test : Primary - Replace
    Failure ID: MBQ3W8-5667NG-9XL03F-C0F403 the Real Time Clock battery needs to be replaced. All the others are the same error message as one can not perform as the Real Time Clock battery needs to be replaced. I recommend to replace the Real Time Clock battery and run the tests again. Here is a link to show you the part number and what you need to do to replace Real Time Clock battery. Page 51 for the part number and shows you how to replace it. I hope this helps, please let me know how it goes. Thanks.   

  • Mac Pro intermediate black screen at boot after installing mountain lion

    I have a 2008 Mac Pro tower, but since installing Mountain Lion I now get a random black screen at boot. Unplugging the apple cinema 20' power supply for 15 minutes seems to clear the fault. Have had no such problems with other OS until Mountain Lion, seems OK when booting to Snow Lepoard on my other drive?
    Anyone have the same fault?

    Thanks for trying the help! I tried every version of start up, but with no screen it was no good..
    Finally solved the problem, it was the ATI HD 2600 XT graphics card that was dying a very slow death.
    Replaced it this morning with a GT120 Nvidia.
    Anyone with this card should Google it, as apple did a big recall on these..
    http://www.itproportal.com/2011/02/21/apple-extends-warranty-mac-pro-video-cards /

  • Iphone does n't restart and all i see is a blank screen (black screen). I have tried recharging the battrey but no success

    Iphone does n't restart and all i see is a blank screen (black screen). I have tried recharging the battrey but no success

    I rebooted my computer and now it's working.
    When in doubt, reboot, but in my frustration this afternoon it didn't occur to me.
    Thank you all so much for taking the time to answer my question.
    I hope this simple solution will help someone else.
    enjoyride
    I get frustrated with Apple too, but if you've spent any time on an Android device, you would know how lucky we are to have an Apple product. The interface is awful and there are no apps, even to get stuck.
    Again thanks...
    Cyndi

  • Black screen at boot MSI Z77A-G43 with HD7850

    Hi,
    I've tried everything You suggested in this topic. I've upgrade and downgrade bios (official 2.3, 2.4, 2.8, 2,9 / beta 256, 281,296) few times but still is black screen at boot. Now i'm on the newest beta bios 296 and still same issue on Sapphire HD 7850 with my Z77a-G43 board. I know for sure that sapphire working well because I've checked on other mobo with even worst PSU (400W instead 550W Volcano). Before hd 7850 I had gtx460 and swith those few times and always gtx460 works fine, so I don't understand anything right now.
    Tried different slots, also clear cmos.
    Board: MSI Z77A-G43
    Bios: Version 296
    VGA:   Sapphire HD7850 1GB
    PSU:   Modecom Volcano 550W
    Intel Core i5-3570k
    MEM: Kingston 4GB 1600MHz
    HDD: 2xSSD
    Without OC
    OS: Windows 7 64bit Professional
    Can You help me somehow, maybe I did not check something else?

    Quote from: The CPU Whisperer on 22-April-13, 16:06:05
    Do you see the same problem on bios 2.90?
    The Z77A-G43 seems the have difficulties accepting HD7xxx AMD VGA cards lately.
    It seems that the problem is gone. I thought of it being an ATI driver issue ~ but not even the latest didn't fix it. But since I flashed to BIOS 2.9 I haven't encountered the problem anymore. So I believe something is fixed between 2.3 to 2.9.
    However my problem was a bit different that the OP has.
    Oh, and I said this on other thread so I say it here too: MSI and Asus 7xxx cards haven't faced the kind of issues Sapphires are having. I'm so glad to my choice... as I almost picked Sapphire but then read comments on Newegg which weren't in favor for Sapphire.

  • My ipod has a black screen.  I have tried to hold the sleep/off button and menu button at the same time with no luck.   I connected to my computer and tried restore on itunes -  still with a black screen a voice said "screen locked'  code 542

    My ipod has a black screen.  I have tried to hold the sleep/off button and menu button at the same time with no luck.   I connected to my computer and tried restore on itunes -  still with a black screen a voice said "screen locked'  code 542

    Is the iPad charged?  Plug it in with the charger/wall outlet for half an hour and try again to reboot by holding both the power and home buttons until the apple logo appears.

  • HT201263 Problem is a black screen. I have tried all the recommendation from the support article, however the iPhone 4 screen still remains black

    Hi, My wife has developed a problem overnight after charging her phone. The Problem is a black screen. I have tried all the recommendation from the support article, however the iPhone 4 screen still remains black

    Take the iPhone to an Apple store genius bar for testing, and if it is defective and under warranty they will replace.  Since you say iPhone 4, was this a used or refurbished iPhone? 

  • Win 7/Z580: Black screen on boot up, before login screen?

    Win 7/Z580: Black screen on boot up, before login screen?
    =======================================
    I find some interesting posting in this forum. Thanks for keeping this forum to help windows/Lenovo community. I like to pick up the brain of this forum to resolve the black screen issue. I am not sure, whether it caused by virus. I use Microsoft Security Essentials. I am not able to run this in command prompt.
    I started my laptop this morning & login screen showed up. Once I entered my login credentials, I heard the sound that usually plays once a login is successful, but I ended up with a black screen. After this occurred, I had to hold down the power button to manually shut down the computer. Once I started it up again, I was prompted to do a system repair, which eventually ended up with all successful outcomes, but I now have a black screen with a cursor before the login screen now. I have no idea what caused this to happen. My laptop is a Lenovo Ideapad Model Z580 (500 GB HD, 6GB RAM).
    I am not able to get into safe mode or any other mode, which all leads to a black screen described above. I am able to use the "Repair Your computer" tools after pressing F8 during booting only . All other options leads to Black screen with cursor in the middle
    Last Known Good Configuration leads to same
    Enable Low Resolution Video (640x480) leads to same My Z580 is not responding to CTRL+ALT+DEL Windows Logo keys as well.
    **** I tried SAFE Mode. It loaded couple of drivers and paused at CLASSPNP.SYS load. It went to Black screen with cursor at center.
    I am able to invoke control pannel from Command prompt of working PC by typing control.
    Z580 PC is not responding to control from command prompt (under Repair Your computer)  either.
    Z580 is able to use the "Repair Your computer" tools after pressing F8 during booting .
    Under local user login it provided Start Repair option. As I pick this option, I got the following. Problem signature
    Startup repair offline
    1 - 6.1.7600.16385
    2 -
    6.1.7600.16385
    3 - unknown
    4 - 21200332
    5 - autofailover
    6 -
    4
    7 - NoRootCause
    os v - 6.1.7600.2.1.0.2561
    locale id – 1033
    Under Admin user login, it provided system recovery options. It is not picking up the recovery point created a while ago.
    Windows Memory Diagnostics is not launching and shows a black screen without cursor.
    I am able to get into command prompt. I tried the following there.
    I am not able to run cmd as admin
    I reviewed the past posting of this forum on this subject.
    Windows 7 boots to an unresponsive black screen with mouse cursor...
    System File Checker: Run sfc /scannow & analyze its logs in Windows 7 / 8
    Windows Resource Protection could not start the repair service
    How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program generates in Windows Vista
    Force SFC to Run in Windows 7
    Windows Resource Protection found corrupt files but was unable to fix some of them
    SFC /SCANNOW showed up
    "Windows Resource Protection could not start the repair service
    I did "net start trustedinstaller"
    "Windows Resource Protection detected pending repair restart the computer"
    I ran repair options using sfc /scannow /offbootdir=x:\ /offwindir=D:\windows
    and got "Windows Resource Protection found corrupt files but was unable to fix some of them "
    I did findstr /c:"[SR]" %windir%\logs\cbs\cbs.log >sfcdetails.txt I will be glad to attach the zip file that contain CBS.LOG & [SR] tag extract (xxx.txt).
    I did not any find ERRORS there, SFC ended with message saying "found corrupt files but was unable to fix some of them" . It is misleading. There is no [SR] tag pointing to corrupt files. Does SFC through false positive like this?
    I ran chkdsk. ResultsFile verification completed.
    0 bad file records processed.
    0 EA records processed.
    CHKDSK is verifying indexes (stage 2 of 5)...
    Index verification completed.
    0 unindexed files scanned.
    0 unindexed files recovered.
    Windows has checked the file system and found no problems.
    0 KB in bad sectors.
    Failed to transfer logged messages to the event log with status 50.
    It is puzzling me.
    Thanks for helping.

    I tried these steps 8/7/2015. I ran chkdsk. Results for D:\
    File verification completed.
    0 bad file records processed.
    0 EA records processed.
    CHKDSK is verifying indexes (stage 2 of 5)...
    Index verification completed.
    0 unindexed files scanned.
    0 unindexed files recovered.
    Windows has checked the file system and found no problems.
    0 KB in bad sectors.
    Failed to transfer logged messages to the event log with status 50.
    Updated on 8/7
    ============
    Here are my HDD config:
    Volume ### Ltr Label Fs Type Status Info
    Volume 0 F WDO_Media64 UDF DVD- Healthy
    Volume 1 C NTFS Partition Healthy
    Volume 2 D Windows7_OS NTFS Partition Healthy
    Volume 3 E LENOVO NTFS Partition Healthy
    Volume 4 G FAT Removable Healthy
    Volume 5 LENOVO_PART NTFS Partition Healthy Hidden
    I ran CHKDSK /F /X for C, D, E. All resluted to "Windows has checked the file system and found no problems."
    F8 ===> Repair Computer===> Command Prompt ===> Works OK
    F8 ===> Repair Computer===> Start up Repair ==> Results into "Startup repair could not detect a problem"
    F8 ===> Repair Computer===> System Restore ===> "No restore points has been created on yout computer system drive"
    F8 ===> Repair Computer===> System Image Recovery ===> "Windows cannot find a system impage on this computer"
    F8 ===> Repair Computer===> windows Memory Diagnostiyics ===> "Black screen with Cursor in the middle"
    After getting into Command prompt
    I run net user
    User accounts for \\
    Administrator Guest
    The command completed with one or more errors
    It did not list other users in my laptop. I do not know why? I tried under F8 ===> Repair Computer===> Command Prompt ===> Works OK
    Here is the result:
    - Boot with Last Known Good Configuration (F8 menu) ===> Black screen with cursor in the middle
    - Restore to a prior date (System Restore) - System Restore ====> Already reported in previous reply
    - Try a clean startup Troubleshoot Application Conflicts by Performing a Clean Startup results in
    Clean Start up
    D:\Windows\System32>runas /user:administrator msconfig
    Enter the password for administrator:
    Attempting to start msconfig as user "MININT-84TH5FG\administrator" ...
    RUNAS ERROR: Unable to run - msconfig
    1060: The specified service does not exist as an installed service.
    - Try loading defaults in BIOS - F2 ==> f9 ==> f10 ===> Black screen with cursor in the middle
    Check if explorer.exe is running and start from CTRL+ALT+DEL (task manager - new task) ===> CTRL+ALT+DEL not responding
     Is anybody in this forum point me to fix? Thanks for looking into this issue. 

  • I have been trying to download adobe reader several times I have tried to click run and save the adobe reader installer box pops up with a blank black screen. I have browser IE 11

    I have been trying to download adobe reader several times I have tried to click run and save the adobe reader installer box pops up with a blank black screen. I have browser IE 11

    Try using the offline installer from http://get.adobe.com/reader/enterprise/
    [topic moved to Adobe Reader forum]

Maybe you are looking for

  • RT multi-motor motion control in a closed loop system

    Hello NI Community,    We have 12 stepper motors with load cells attached in line on each motor that are connected to a RT PXI chassis.  We use an optical system to gather 3D data on the host computer which is used to calculate relative angles betwee

  • Deltas are not coming to RSA7 from SM13

    Hi All, In BW i am not getting Delta's for 2LIS_02 Datasources, I have checked in RSA7 it is showing 0 Records, but in SM13 there are many V2 Processed Jobs. Please can anybody help me how to get Delta's to RSA7, this problem is persist since 1 week.

  • Services not started in Visual Administrator

    Hi, I have problem with the some of the services. After I start the SAP J2EE Engine, I can see that most of the sevices are not started in "deploy" link. All the services get started when I manually start the application. I am working with NetWeaver0

  • Error when trying to use DO as "open collector" on PXI-6602

    When I try to configure a DO of my PXI-6602 as "open collector" I receive the error -200452 ("Measurements: Specified property is not supported by the device or is not applicable to the task."). This is completely mysterious to me since the PXI-6602

  • WIP and COS calculation in Project Systems

    I am trying to determine WIP and COS using KKAJ.  WIP always returns 0 while COS returns the totaled planned cost as COS.  I cannot figure out why this is so.  Any ideas what I should change to correctly calculate COS and WIP?  I have already maintai