Xserve RAID will not mount to my Mac Pro

We just moved the Xserve Raid to another Mac Pro with 2x3 GHz Quad-Core and 16 GB of Ram. I installed the Xserve card, plugged the cables into the tower and into the Xserve, powered it on, installed the updated Raid Admin, but it wont mount. I checked disk utility and I dont see it there either. The lights on each drive are an amber color so I know something is not right. I wanted to find out what step am I missing, if I am missing some software, if pulling the drives out before moving it caused a problem, or any other suggestions. Any help would be greatly appreciative. Thanks!

If you're not worried about the contents of the drives that a good start because I don't think that's recoverable. What does RAID Admin say about all the other components? Are the controllers green? Technically the yellow lights on the drive are supposed to signal drive issues but I don't know why all the drives would suddenly be an issue without a deeper issue.
Fire up RAID Admin and see what's going on - you're going to need it to delete and try and recreate RAIDs anyway.
Good luck,
=Tod

Similar Messages

  • Xserve Raid will not mount - fibre channel link down

    I came back from being out of town and my Xserve is running, but will not mount on the G5 tower via fibre channel. It was powered off and up again and still nothing. Apple tech says to reset raid controllers, however, I have sensitive data on the drives and lots of video/FCP projects on there. It has just run out of warranty and now asked to pay $199 per incident to get any help. I will gladly take any help.
    Read the boards, ran Disk Utility and still did not show up.
    Also, told the fibre cables tend to "burn out" but have yet to spend money if this is not the problem.
    Thanks.

    Resetting the controllers is non-destructive. However, if you power-cycled the array, that should take care of it.
    told the fibre cables tend to "burn out"
    I've never experienced (or heard of this) myself, and have never had a problem on any of my arrays, some of which have been running for years with zero problems. Of course, environment (especially heat) could play a part, but it seems a little bit of a stretch to me.
    Does RAID Admin have anything to say about the RAID?

  • Dvd will not mount on my MacBook Pro

    dvd will not mount on my MacBook Pro. The disc will spin up briefly, then spin down and then eject.

    Check Finder / Preferences - General
    Make sure CDs, DVDs, etc is selected.

  • External backup drive will not mount on new mac mini. still works fine on the old one. new one is running mavericks

    I just bought new-to-me mac mini running OSX mavericks.
    Trying to migrate from old mac mini using simpletech external hard drive.
    It still mounts on my old mac mini (system 10.5) but will not mount or show up when I plug it in to the new mac mini running mavericks.
    Any ideas?

    BDAqua wrote:
    What exactly shows in System Profiler>Hardware>USB for those drives?
    Boot from the Install Disc & see if they show up, not grayed out in Disk Utility.
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    We were thinking along the same lines. While at home I dug up a firewire enclosure and put a bootable GUID formatted drive in it (that I had in one of the usb enclosures) and started her computer holding down the option key and then chose to boot from the external firewire. All usb drives are now mounting upon connection. I asume that her drive has bad sectors on it (even though the SMART status says it's OK) and is not loading all the drivers properly for USB to mount. I was suspicious from the beginning that the OS was corrupt when she first had me look at it. It was at that point that I booted it in target mode, connected to my Macbook Pro, and then CCC'd to a usb drive that I had. I then had a couple of difficulties installing the new OS. Should have known......
    I am now going to put a new drive in it for her and she'll be up and running.
    Thanks so much for your help and thoughts that got me thinking as well.
    pax

  • Firefox 3.6.13 will not mount on my Mac 10.3.9

    I tried downloading Firefox 3.6.13 for the first time on my Mac 10.3.9 and get the message that it will not mount.

    Firefox 3.6.13 requires at least OS X 10.4, the last version of Firefox to work on OS X 10.3.9 was Firefox 2.0.0.20
    ftp://ftp.mozilla.org/pub/mozilla.org/firefox/releases/2.0.0.20/mac/en-US/

  • My external hard drive will not mount with my mac?

    Okay so everything was working out great till the new OS came out. Then i ran into some problems. I can no longer back up anything i have on my laptop anymore because my external will not pick up in finder-desktop-etc. I need help as fast as i can because i need to back up, its been 50 days and my computer is filled with pricless photos and videos that i would like to save.
    Please help!!!!

    No it does not, sorry that this responds took so long

  • Windows and xp will not boot (1st gen Mac Pro)

    i have a first generation mac pro and i am having trouble booting into my boot camp volumes.
    when i run an option boot i get four icons
    1. Lion
    2. windows
    3. windows
    4. disk recovery
    i have a note on my screen here that tells me the first windows icon is windows 7 and the second icon is windows xp. however, every time i click on one of these disks the screen either locks up or the icon stays selected and i have to do a /manual/ shutdown and it /usually/ will boot into whatever windows volume i had selected.
    NOW when i try this i am getting windows recovery messages and when i tell it to boot into windows normally it kicks me out to a computer RESTART and then it will boot into Mac OS.
    i realize i can /change/ the regular boot volume to trick it into booting back into whichever windows volume i am trying to use but at this point this all seems like things are going off the rails somehow.
    i have just recently moved all my data to drive 3 and am cloning this data to drive 4. drive 1 is Lion with a partition containing windows 7 and drive 2 is a 500 GB volume containing my xp install.
    SHOULD I pull out all the disks and put them back in to make sure they are seated properly? should i move them around physically in the drive perhaps? should i run some software boot restore/re-index software?
    i really, really have to finish this reconfiguration of my machine but - is it possible this is simply due to the age of the computer in which case i will spend time on this after buying a new mac pro that will upgrade to Mountain Lion...
    TIA, jon
    (also posted in mac pro forums)

    holycow.
    this is helpful to know.
    thanks i will check into this.
    man, this could be a bit of an issue over here which i have to wrap my head around...

  • OS xSnow Leopard will not upload on my mac pro currently at 10.5.8. I get as far as the restart section of the download then the driver tray opens. Can you help?

    Having problems upgrading my Mac Pro 10.5.8 to OS X Snow Leopard upgrade that I bought from Apple Online. I get as far as "Computer will restart and then continue with upload". The problem is that after the restart takes place my driver draw opens and the Updrade doesn't continue. I've tried serveral times without success. Not sure what the problem is. Please Help?

    Confused. 10.6 is DVD based. Only Lion and above are downloads.
    And best install is not to upgrade. Do a clean install  - on another drive.
    Corrupt partition tables or bad sectors or no room to adjust the partitions or the directory is corrupt.
    ERASE the drive if Repair Disk didn't work.

  • Vista Ultimate SP1 (retail dvd) will not install on new Mac Pro

    I wish to dedicate a new 1TB hard drive in Bay3 on a brand new Mac Pro for Vista Ultimate SP1, preferably 64-bit. I have tried several times to install a retail dvd version of Vista Ultimate with SP1 (both 32- and 64-bit) without success on two different hard drives (first the one in bay 3; then, after lack of success, the one in bay 4). The installation process does not proceed beyond the stage where Vista must format the hard drive. Vista always displays the message that Vista cannot be installed on a disk of the "GPT style." After giving up on the installation, the disk appears to Disk Utility as a "GUID" disk.
    I am seeking advice from anyone who might be able to help me proceed. The remainder of this message provides more detail about what I have tried.
    Before starting Boot Camp, I formatted the hard drives initially as MS-DOS FAT, and on later attempts, as Mac OS Extended (Journaled). Neither matters. After several attempts, I verified the functionality of the drives by partitioning them using Disk Utility and then repartitioning to one partition. Both 1TB drives appear healthy and can be partitioned and re-partitioned.
    When Bootcamp Assistant (BC) calls for the Vista disk, the Vista installation proceeds until the stage when Vista calls for me to identify a hard drive partition for installation. After selecting the largest partition on drive 2 (in bay 3; size 931GB) , the BC Installation and Setup Guide instructs me to "format" the partition. When I do so, the following Windows error message appears:
    "Windows cannot be installed to this disk. The selected disk is of the GPT partition style."
    Based on some forum comments, I also tried a different procedure at this stage of the Vista installation. Instead of choosing "format," I first chose to "delete" the selected partition. The disk then appears as "unallocated space." I then chose "new" and "apply" in the hope that it would create a correct NTFS partition for Vista. It then appears as Partition 2 of either Disk 2 (or Disk 3, which I tried subsequently). However, the subsequent "format" still yields the same error.
    I tried both procedures with Vista 64-bit and with Vista 32-bit. No difference.
    Suggestions most welcome.

    When I provided a link to threads about "Install Vista SP1 DVD" I knew and had in mind a couple threads where people have tried. And trying will help understand.
    You don't need to format as NTFS on another PC when just installing MacFuse plus 3G driver extensions will let you do so on your Mac Pro. And that is just one option. There are always multiple ways to get to the same place.
    Due to EFI changes there is a tool and tips on how to convert your DVD, but I didn't have time to go back and find and pull those together.
    Installing SP1 DVD attempt without success:
    http://discussions.apple.com/thread.jspa?threadID=1501656
    http://www.ezbsystems.com/ultraiso/
    MS OSCDIMG.exe
    Yes, it’s a fairly long process and requires you to download stuff (and be running Windows in the first place) But, it does work as long as you follow the instructions correctly.
    Convert DVD to ISO and prepare for EFI booting on Mac
    tried rebooting about 10 times. No luck. Finally I pointed Parallels (free trial available) to my blank bootcamp partition and set parallels to boot from CD before HD. Parallels booted the Vista install CD just fine, and put Vista on my HD. Crashed at the end though and said it couldn't make the boot camp partition bootable so all changes were removed. Rebooted under boot camp and the installer came up fine off the CD.
    So if you have this problem, and nobody else can help, and if you can find it, maybe you can download..... Parallels. Feel free to post this on the other threads. Unlike other workarounds I'm guessing this will work for everyone and it only takes a free trial download of parallels to give it a try. Still wish apple would acknowledge the problem and post a fix. Can't be that hard.
    I think VMWare Fusion also supports vitualization with the bootcamp partition as the target so that may help you get around this install bug in boot camp(or the mac's firmware) too.
    I would have thought that with Intel and Microsoft both saying they would begin to support UEFI with Vista SP1 64-bit, and Apple is part of the EFI Group, that "we're different" was a thing of the past. Instead it is harder.
    http://www.microsoft.com/windows/products/windowsvista/sp1.mspx
    Remember, Google is your friend (usually) - "Apple Vista SP1 64-bit DVD Install":
    MacBook Pro Vista SP1 64-bit Install:
    http://andersonshatch.wordpress.com/tag/vista-64-bit/
    Oh, and while I read Apple KB changes daily, I have never seen anything address Vista SP1 64-bit install, support, etc mentioned once. Am I missing something? or is it MIA?

  • My iPhone 4s will not connect with my mac pro

    hey, so i have an iphone 4s with the latest update iOS7.1 and a macbok pro which is also up to date with itunes 11.1.5. The entire time ive had this computer and this phone all i had to do was connect the two via USB and my computer recognized my phone as well as itunes and proceeded to sync all my things automattically sometimes it would do it even if the devices werent connected but even if they were close in proximity they would connect, no problem. BUT now it will not do that when i connect it via usb neither one recognized that they are connected my phone will charge but thats about it, every once and a blue moon my phone will recognize the computer and ask if the computer is trusted to which i select "trust" and then it tells me its unable to connect but that barely happens most of the time nothing. Ive tried the typical restarting my computer, restarting itunes, searching for updates but its not just itunes that doesnt recognize my phone its my whole computer it seems, what could have happened to make these two devices unable to connect? how do i fix it?

    iOS: Device not recognised in iTunes
    Mac: http://support.apple.com/kb/TS1591

  • Mountain Lion will not load on my mac pro with 10.7.4.

    I purchased and tried to download Mountain Lion to my mac pro and it will not down load. Once I press download it does nothing. I have already been billed for it. My mac pro notebook is less than a year old opperating 10.7.4 Lion. Any ideas?

    restart your computer and try again, when you hit download, do nothing, and hopefully it will begin, do you see the installer in Launchpad? try double click it to unpause it.

  • Driver disk will not auto run on Mac Pro 08

    Hi
    I have a Mac Pro early 08 and i'm finding the Leopard driver disk will not auto run "to install" drivers but it only gives me 2 other options for disk share and something else which I forget now as I un=installed.

    Hi
    Oh god no I popped the disk in when WVU finished installing and arrived on the desktop and it only gives me 2 install options.1.for the MB air and another for disk sharing but why does it not install drivers aotomatically?
    The driver disk does not aoto run under vista and which drivers do I use ..also the ATI just does not want to work "advising errors of hardware or software" not installed.
    I have done this numerous times on the iMac and XPP worked fine with the driver disk but WVU is giving me headaches.
    Message was edited by: macbookair

  • My mac pro will not power up, my mac pro will not power up

    My Mac Pro will not power up.

    If you are still under warranty and/or have AppleCare, call them.  Let them deal w/it.

  • Any reason a G5 Graphic card will NOT work in a Mac Pro as a second card

    Should I try this?  I don't see any reason why not but would like to make sure
    Thanks

    Should I try this?
    No.
    It won't work.
    Any reason a G5 Graphic card will NOT work
    As explained, the G5 uses Open Firmware and the Mac Pro uses EFI.
    The ROM of the graphics card is completely different for each of the two machines.
    The cards are not interchangeable.

  • Final CUt Studio 2 will not run on my Mac Pro & Macbook Pros simultaneously

    I was under the impression that the licensing contract for FCPS2 allowed for the software to be installed and run on a desktop and a portable machine simultaneously. Am I wrong? I purchased Final Cut Studio 2 legally, and have installed it on my Mac Pro and my Macbook Pro, but if I try to open one of the FCS apps while one is running on the other computer, I get a protection error message and have to shut down the app. Does anyone know a workaround to this other than shutting off airport on one of the machines?

    I was under the impression that the licensing contract for FCPS2 allowed for the software to be installed and run on a desktop and a portable machine simultaneously. Am I wrong?
    Yes, you are wrong.
    The license allows for the installation of a copy on each machine but they can not run simultaneously. The intention is to allow users to work with a laptp while away from the main editing machine. If you need the capability running two copies at the same time, buy another copy.
    Good luck,
    x

Maybe you are looking for