Xserve running Server 10.5 rebuilt now DNS resolving very very slow

Hi There,
Have had to rebuild an OSX 10.5 Xserve (2008/9 model)
All seems fine apart from DNS is incredibly slow at resolving addresses.
I'm using a failt simple 1 NIC setup
Server IP 192.168.1.1
S/N 255.255.255.0
DG 192.168.1.254
DNS 192.168.1.1/127.0.0.0 (have tried both)
In the DNS setup on the server manager I have set the forwarder to the router IP (which is as it was prior to the rebuild)
NOw a ping from terminal either doesnt resolve or after about 2/3 minutes it does resolve.
If i change the servers DNS server to the router everything resolves very quickly so I'm pretty sure something is configured incorrectly in the DNS on server manager.
Looking for some hints as to what may be worng.
Thanks

post the content of /etc/named.conf
By default, this versions if bind will do lookups on its own,,, its prefered to pass those lookups to your ISP.
Start with above. I'll return the changes.

Similar Messages

  • G5 xserve running Server 10.3.9 fails to upgrade to server 10.5

    We have an Xserve Dual G5 XServe with xserve 10.3.9 that was setup out of the box about 4 years ago. We purchased Server 10.5 for an upgrade. After making a full backup we booted from the 10.5 DVD, We are able to click through and select the volume to upgrade, it starts to do the upgrade states it is copying files for a couple of seconds then stops and states unable to install on this volume, you may need to run disk utilities to run this upgrade. I have run the disk utilities, repaired permissions, repaired the disk (neither stated problems) tried again with the same result. I have 2 drives in a mirror configuration that the partition is on. Any thoughts.

    Hi Sean Clark4-
    Greetings and welcome to the Apple Discussion boards
    How much free space on the destination volume?
    You may need to create the partition using 10.5. I would suggest a full backup to an external drive or two before attempting this upgrade anyway, and you could restore the information once the upgrade is complete.
    Luck-
    -DaddyPaycheck

  • Disk image mounting and disk utility oddities on Xserve running OS X Server

    I continue to run into an odd problem on one of my server setups. It is a 1.33 GHZ Xserve running OS X Server 10.4.11. There are four ATA drive installed (two of which are mirrored using Softraid 3.6.6). There are a total of 6 Firewire drives on the Firewire 800 Bus. Three of those are used for sharing out files and the other three are for various backups.
    What happens is that I sometimes run into an issue where dmg files will not mount. There are no error messages and nothing in the log, they just don't open. Likewise I am unable to launch Disk Utility, it just spins and spins never displaying the drives, again nothing in the logs, no crashreporter. I have also found out that the same thing happens in System Profiler when I try to get a list of drives on either the ATA bus or the Firewire bus. Mind you they all show up on the desktop. Likewise I have had no luck getting them to list or run permissions or the like from the diskutil commandline. Now I am able to mount actual drives. When I swap out the offsite backup drive it mounts the new drive just fine. However... when I eject the drive and it has disappeared from the desktop and then I remove it... I get the removal error.. you didn't put the drive away properly message.
    Now there are no disk related events showing up anywhere in the logs. The only other oddity that I can see is that my rsync backups tend to generate a ton of zombie processes. I get zombies of cron, sh, rsync, and mail.
    It is just a pretty straightforward shell script
    /usr/local/bin/rsync -E --archive -eahfs --delete /Volumes/Files/Shared\ Items/ /Volumes/Backup\ Files/Shared\ Items/
    Running in cron with it set to email the logs.
    Now this does all clear up when I reboot the server... but it also doesn't reboot cleanly. It closes down all of the applications, login window and the like and then hangs on the shut down portion. Eventually I have to power it off manually. I've done the normal Volume checking on the main drives and they come up with 0 errors.
    Hoping someone might have some ideas before I end up having to backup and reinstall the whole thing.

    Also when I try to open the disk image file I get the following error in the log.
    xserve kernel[0]: disk10s10: media is not present.

  • Xserve running Windows Server in a VM

    Hi Guys,
    We're looking to completely replace 4 servers, 2 are windows servers and the 2 are linux servers. We require to keep running those windows services for clients for now. Can Xserve run Windows Server in a VM properly?

    I don't know why any small shop would buy a Windows box to run Windows.
    It can be done better on the Mac with virtualization.
    Read this link:
    http://discussions.apple.com/thread.jspa?threadID=2417389&start=0&tstart=45
    I'm 145 days of uptime with a 2008 Xserve 2x3.0GHz/12GB/3x1TB/10.6.3/Parallels 5.x running four W2K3 VM's and one NT4 VM. The setup is 2x1TB software RAID-1 in Bay 2/3 with a third 1x1TB in Bay 1, and a 1TB 2.5" USB drive hanging off the back. Utilization with 10 clients is <10%. Yawn.
    Scheduled SuperDuper flings the Bay2/3 1TB RAID over to the internal 1TB in Bay 1 and the USB at night giving my a 1 day stale backup of the running VM's.
    I can pull the USB out, plug it into my 15" i7, double click on the VM's and run the whole office.
    The Parallels Transporter app can often be used to pull your entire server over into the virtual environment on the Mac, so your clients don't even know anything happened.
    You will need legit/licensed/bonafide Windows with keys to do this, as Windows will recognize that the hardware has changed and want to be re-activated.
    Get Parallels, dump your Windows boxes and don't look back.
    If this is your first Xserve though, be prepared.
    It's loud and hot.

  • Server Monitor on Xserve running Client OS

    I have an Xserve running the regular client OSX (Filemaker Server, didn't see the point in installing the full Server OS). Is there any way to get Server Monitor running? I would like to be able to keep an eye on the hardware functions.

    Is there any way other than loading Mac OS X Server, you mean? Not directly.
    You could enable and use the [SNMP daemon within the Leopard Mac OS X client|http://www.bynkii.com/archives/2007/12/aprimer_to_snmp_on_mac_os_x1.html], but that won't give you the Server Monitor interface.
    Or you could see if the [Lithium software|http://lithiumcorp.com] is sufficient for your needs.
    Or you could load the 10-client Mac OS X Server distribution, which has the monitoring stuff baked in.

  • XSERVE Cluster Server Keeps Shutting Down

    I have a G5 Xserve Cluster server. Been working like a charm the last couple of months, but now I have a problem. It just shuts down. Nothing dramatic. Will be running for a while and then click... it goes off.
    Any suggestions as to what could be causing this before I go to the apple store. PRAM Battery?
    It is completely random and can occur 10 seconds after starting up or 20 minutes in.

    I'd be checking the error logs for clues.
    Any chance it is overheating? Are the air vents clear of dust and debris?
    Are you using a properly rated UPS?

  • Open dns resolver issues on windows server 2008 R2

    my client is running a windows 2008 r2 server with dns and dhcp roles. it's not a domain controller, just a workgoup server.
    got a notification from my client's isp:
    "These attacks have been facilitated through DNS
    amplification attacks. AT&T has detected these attacks and has confirmed
    that the IP address x.x.x.x allocated to your Internet access account is
    accessible from the Internet as an open DNS resolver. "
    tried disabling recursion, but then there is no access to the internet.
    tried disabling the firewall rule for dns udp, and no access to the internet.
    does anyone have any idea how to correct this? do i need to add a public dns server to my dhcp scope for internet access? if i do, then what good is a dns server and it doesn't resolve internet addresses?
    Gary

    Just to add, I was wondering why you had port 53 opened to your DNS servers. And just to point out, that rule you created is a port translation rule that allows access to your DNS server from the internet, just as if you had created a rule to allow access
    to an internal web server for public use, or for allowing webmail (OWA) access from the internet to your internal mail server.
    What you did, as Keith said, will stop that, but to further point out, the rules are not really needed again, I would just remove the rules completely. For internet access, such as allowing your users to access websites, your DNS to resolve external names
    (whether using Root hints or a Forwarder), just about any firewall will allow that out-of-the-box. In some firewalls, you have to create a rule to the outside untrusted interface to "allow established" meaning when an internal request goes to an outside resource,
    such as a website, to allow the response back in.
    The only time you want to create rules is either you want to allow inbound traffic with a port translation rule (such as what you originally unknowingly did for TCP & UDP 53) to a web server, OWA, SMTP traffic to a mail server, etc.), otherwise,
    leave it out of the box.
    As for what the ISP is concerned about regarding DNS amplification attacks, is that they are a fairly recent method for attackers to create a DOS (denial of service). You can read up at a couple of recent discussions about what all that means in
    the following threads, with ways to stop or mitigate them.
    Best way to reduce or disable DNS amplification for external DNS?,
    Sunday, June 16, 2013 6:08 PM
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/d087a768-2075-49e4-afec-4fd23b50af0a/best-way-to-reduce-or-disable-dns-amplification-for-external-dns
    Protecting Windows DNS Server from being abused for DNS amplification attacks,
    Wednesday, April 10, 2013 8:05 AM
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/fac86dc7-779d-48eb-a113-9c06c2222af9/protecting-windows-dns-server-from-being-abused-for-dns-amplification-attacks
    Ace Fekay
    MVP, MCT, MCITP/EA, MCTS Windows 2008/R2 & Exchange 2007, Exchange 2010 EA, MCSE & MCSA 2003/2000, MCSA Messaging 2003
    Microsoft Certified Trainer
    Microsoft MVP - Directory Services
    Technical Blogs & Videos: http://www.delawarecountycomputerconsulting.com/
    This post is provided AS-IS with no warranties or guarantees and confers no rights.

  • Adding a Datasource to a running Server ?

    What is the best way to add a new data-source to a running Server ?
    Perviously, I was binding a new DataSource Object into the JNDI Tree from the context of an EJB, with an external process writing the new DataSource into the data-sources.xml file.
    But now I've kicked EJB's out of the application, replacing with POJO's accessed from the servlet tier and the binding of the datasource fails (unusual issue and all my other Objects bind perfectly, I'll continue investigating...)
    Now, I know that the admin.jar file can be used to manually add new data-sources to a server, but is this the best way to add data-sources to an already running server ?
    Could I in some way call into the appropriate Class to add a new data-source.
    e.g. A Server API like this: OC4JServer.addDataSource( Map params ); would be handy
    Cheers,
    Ro

    Hello,
    One way of doing that in OracleAS 10.1.3 will be to use JMX and MBeans.
    The getMBeanServer() returns you an MBean Server connection where you can invoke operations as follow:
    String appBeanName = "oc4j:j2eeType=J2EEApplication,name="+ j2eeAppName +",J2EEServer=standalone";
    ObjectName obj = new ObjectName(appBeanName);
    // invoke the create connection pool and create connection
    // values used to create the connection pool
    Object[] paramsPool = {
    connectionPoolName,
    dataSourceFactory,
    username,
    password,
    url};
    // signature used to create the connection pool
    String[] signaturePool = {
    "java.lang.String",
    "java.lang.String",
    "java.lang.String",
    "java.lang.String",
    "java.lang.String"};
    // Call the connection pool creation operation
    getMBeanServer().invoke(
    obj,
    "createJDBCConnectionPool", //operation
    paramsPool,
    signaturePool);
    // Values used to create the connection
    Object[] paramsConn = {
    connectionName,
    username,
    password,
    "jdbc/"+ connectionName,
    new Integer(30), // timeout
    connectionPoolName,
    "global",
    null};
    // Signature used for the Operation call
    String[] signatureConn = {
    "java.lang.String",
    "java.lang.String",
    "java.lang.String",
    "java.lang.String",
    "java.lang.Integer",
    "java.lang.String",
    "java.lang.String",
    "java.lang.String"
    getMBeanServer().invoke(
    obj,
    "createManagedDataSource",
    paramsConn,
    signatureConn
    Regards
    Tugdual Grall

  • Single server as Soft AP, DC, DNS, DHCP for a small office

    The server is running 2012 R2 Foundation with a wired network for internet (Comcast). It has a WiFi adapter so it can host a wireless network (as a Soft AP). The WiFi host has a static IP 1.1.1.1.
    On the server I have setup AD, DNS, and DHCP services (all bind to that static IP).
    All clients need to connect server and internet via WiFi, and join the domain for work.
    But it looks like the DHCP/DNS services don't like the virtual adapter - although all clients can connect, they cannot get their IP.
    Without AD/DNS/DHCP I can share internet connection with ICS perfectly, so I think the hosted WiFi network is setup correctly.
    I tried to remove the DHCP service, and use ICS to assign IP - it works, but clients cannot see the DNS server and thus cannot join AD.
    What am I missing? Thanks for your help!

    It is never a good idea to run a DC with two NICS. It causes all sorts of problems. (The only exception was SBS server which was designed as a one-box solution). Also, a domain will not run behind ICS. If you are running a domain, the domain clients
    must use the local DNS (on the DC) for DNS, not the DNS relay system of ICS. RRAS/NAT will work because you can configure it so that it does not run its own DHCP function. ICS is not configurable.
      Even if you overcome that problem, you still have the multihomed DC problem. It really isn't worth the effort to save a few bucks.
    Bill

  • Small Business w/Mac Mini Running Server OSX, Connect From Home Solution - VPN?

    I am trying to setup my Mac Mini running OS X Server (Mountain Lion) to be accessed from users at home (for file sharing and Contact Services). Is a VPN the best solution? (Small business setup - privacy/security a concern).
    Hi everyone, and Thanks for the help in advance!
    I am currently setting up a network for my company (small business) and have a few questions. We have a Mac Mini (mid-2012) running Server OS X Mountain Lion, and 5 MBP's (our work computers- all running latest version of Mountain Lion).
    To summarize:
    My goal = Setup a secure way of connecting the MBP's to the server when our personnel are at home (for file sharing).
    I am switching all of the users from local to network (we didn't need the network functionality when we first setup the server, and we are now expanding our use of it). This is going to occur this weekend, as downtime for the server is needed to make the changes.
    After I establish the Open Directory and all of that, I will be setting up Contact Services (to share a master list of contacts with the members of our department) and we already have some Calendar sharing setup.
    The purpose of this is to enable our employees the option of working necessary overtime from home so they can be with their families instead of in the office all the time. It is a noble cause and I want to set this up the best that I can for them.
    This being said... I'm no Mac Genius, and this stuff can get very confusing very fast. I have read a little about VPN's, and am wondering if this is the solution to my problem. We need to establish a SECURE way of connecting to the server from remote locations, enabling us to pull needed files from the server.
    If anybody can offer some advice on this I would really appreciate it. I love Apple products and I have faith that this is as easy as I've been told it is.
    Thank you very much for your time and consideration!

    No, it wasn't difficult at all to setup in OS X Server. I use a free internet domain name from DynDNS.com. I don't know if they still offer free ones anymore. You can not use VPN and 'Back to My Mac' at the same time as they use some or all of the same ports.
    I'm at work and not on my Mac at the moment so this is from memory.
    Within OS X Server, I enabled the VPN Service (default L2TP) and used my free domain name in the VPN Host Name and a Secret passphrase. This put an entry in my Airport Extreme router for VPN (port mapping).
    Within the client Mac, I added a VPN network connnection (System Preferences /Network). I pointed to my free domain name in the Server Address, used my Server account name in the account name. I think there's an Authentication button that I clicked. I entered my Server account password, the Secret passphrase in the Secret field, checked a box to show VPN icon in Menu Bar and exited out of that. Then clicked the Advanced button and checked the box to send all traffic over VPN connection.
    I had VPN authentication issues at first when trying to connect to test out the connection. I just kept trying as I knew I had all the settings correct and it would finally connect after about 3-4 tries. After that, I sometimes have to connect more than once to actually connect to my Server via VPN. But it does work nice. I brought my MBP into work once to test it out and was able to connect to my home Server via VPN and use Screen Sharing and had access to all my shared folders.

  • Direct Access Server 2012 R2 Single NIC DNS problem with 8.1 Enterprise

    Dear helpers,
    I am beginning to rip my hair over the following problem and I am asking for some guidance:
    I have setup DA on a server 2012 R2 with the simple wizard using one NIC. I have opened up port 443 to my  DA Server and operations status is showing green on everything. I have used Djoin to join a remote win 8.1 enterprise client to our domain and
    setup DA. I can see that my tunnel is established and the client shows up as an IPHTTPS client on my server:
    Role                       : client
    URL                        : https://vpn.ourdomain.com:443/IPHTTPS
    Last Error Code            : 0x0
    Interface Status           : IPHTTPS interface active
    Connection status on client is stuck in connecting and the eventlog on client gives me following error:
    The system failed to register host (A or AAAA) resource records (RRs) for network adapter
    with settings:
               Adapter Name : {424F50B4-BF1A-4D96-81FA-7D7436A99F07}
               Host Name : TEST
               Primary Domain Suffix : ourdomain.com
               DNS server list :
                     172.16.8.1
               Sent update to server : <?>
               IP Address(es) :
                 172.16.8.110
    The reason the system could not register these RRs was because the update request it sent to the DNS server timed out. The most likely cause of this is that the DNS server authoritative for the name it was attempting to register or update is not running at
    this time.
    I understand why this is failing because it seems like it is contacting the local DNS to register and that's wrong.
    Get-DaConnectionStatus gives me the following:
    Status    : Error
    Substatus : CouldNotContactDirectAccessServer
    I can ping the name on the DA server and also the IPv6 address, I can also do nslookup if i set the server used to my internal DNS-servers IPv6 address(DNS and DA server = same machine). My DA Client GPO is being applied to the client and i get an NRPT table
    looking as follows:
    Settings for DirectAccess-NLS.ourdomain.com
    DirectAccess (Certification Authority)  :
    DirectAccess (IPsec)                    : disabled
    DirectAccess (DNS Servers)              :
    DirectAccess (Proxy Settings)           : Use default browser settings
    Settings for vpn.ourdomain.com
    DirectAccess (Certification Authority)  :
    DirectAccess (IPsec)                    : disabled
    DirectAccess (DNS Servers)              :
    DirectAccess (Proxy Settings)           : Use default browser settings
    Settings for .ourdomain.com
    DirectAccess (Certification Authority)  :
    DirectAccess (IPsec)                    : disabled
    DirectAccess (DNS Servers)              : fd1f:6801:cc14:3333::1
    DirectAccess (Proxy Settings)           : Bypass proxy
    I cannot reach any internal resources by name or IPv4 address except the DA server.
    I will gladly provide more info if needed
    Please help!
    //Cris

    Hi,
    Thanks for your reply.
    Firstly, computer certificates are necessary for DirectAccess.
    In addition, it is no need to assign an IPv6 address on all the servers. In Windows server 2012/R2, the
    Built-in NAT64 and DNS64 support for accessing IPv4-only resources.
    If you select Configure DirectAccess Clients with DNS client suffix search list and add additional suffixes to the list,
    you can search for short, unqualified computer names in more than one specified DNS domain.
    For more detailed information about DNS suffix search list, please refer to the link below:
    Step 2: Configure the DirectAccess Server
    Best regards,
    Susie

  • Hi recently my MacBook pro has stopped connecting to our office Synology server automatically.  I now have to Go Connect to Server etc in order to browse the file server. Clearing key chain and then readding everything hasnt made any difference. HELP

    Hi recently my MacBook pro has stopped connecting to our office Synology server automatically.  I now have to Go > Connect to Server > etc in order to browse the file server. Clearing key chain and then readding everything hasnt made any difference. HELP

    Not sure what other tests they could run for me. I've pretty much run all the tests I can using Drive Genius and Tech Tool Pro 5. Is there anything they use that I don't know about??

  • Unknown Host Unable to locate the server requested --- the server does not have a DNS entry. Perhaps there is a misspelling in the server name, or the server no

    Hello,
    Today i tried accessing transitbux.com with mozilla, but i'm getting this kind of a error as mentioned below:
    Unknown Host
    Description: Unable to locate the server requested --- the server does not have a DNS entry. Perhaps there is a misspelling in the server name, or the server no longer exists. Double-check the name and try again.
    Can anyone help me please, and the same website is accessible with my phone.
    Help me please. :(
    Regards
    -

    Try http://www.transitbux.com/
    Clear the cache and remove cookies only from websites that cause problems.
    "Clear the Cache":
    *Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
    "Remove Cookies" from sites causing problems:
    *Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"

  • Dispatcher Running Server Not Connected

    Hi,
    I have the same problem on Windows 2003 Server EP6 WAS640 SR1 SP9
    I have the WAS640 for ABAP with the Java Add In and the Enterprise Portal installed on top.
    When I try to connect to the Portal through a browser I get the message:
    Dispatcher Running Server Not Connected
    In the JCMON I cannot start Server0 and I get the errors 1,2,3,4 and it tries to start and then goes to status STOPPED
    Does anyone know the solution ?
    My system was working, the last change I made was to authenticate users against an SAP system and then I did a reboot and now the J2EE won't start.
    Any help is much appreciated.
    Thanks,
    Tomas.

    some more info, this problem started after I configured the Portal to authenticate against the SAP system
    In the portal system log for server.0.log there is the following info:
    Caused by: com.sap.engine.services.security.exceptions.BaseSecurityException: Anonymous principal not configured
         at com.sap.engine.services.security.login.SecurityContext.setAnonymousPrincipal(SecurityContext.java:504)
         at com.sap.engine.services.security.SecurityServerFrame.start(SecurityServerFrame.java:150)
         ... 5 more
    Caused by: com.sap.security.core.server.userstore.UserstoreException: Could not get user J2EE_GUEST
         at com.sap.security.core.server.userstore.UserContextUME.engineGetUserInfo(UserContextUME.java:187)
         at com.sap.engine.services.security.userstore.context.UserContext.getUserInfo(UserContext.java:87)
         at com.sap.engine.services.security.login.SecurityContext.setAnonymousPrincipal(SecurityContext.java:498)
         ... 6 more
    Caused by: com.sap.security.api.NoSuchUserAccountException: USER_AUTH_FAILED: User account for logonid "J2EE_GUEST" not found!
         at com.sap.security.core.imp.AbstractUserAccount.<init>(AbstractUserAccount.java:334)
         at com.sap.security.core.imp.DBTextFileUserAccount.<init>(DBTextFileUserAccount.java:56)
         at com.sap.security.core.imp.UserAccountFactory.getUserAccountByLogonId(UserAccountFactory.java:339)
         at com.sap.security.core.imp.UserAccountFactory.getUserAccountByLogonId(UserAccountFactory.java:277)
         at com.sap.security.core.imp.UserAccountFactory.getUserAccountByLogonId(UserAccountFactory.java:371)
         at com.sap.security.core.imp.UserAccountFactory.getUserAccountByLogonId(UserAccountFactory.java:366)
         at com.sap.security.core.server.userstore.UserContextUME.engineGetUserInfo(UserContextUME.java:183)
         ... 8 more
    #1.5#00A0D1BC74B6001E0000000C0000118C0003F7536153ADF0#1116362417365#/System/Server##com.sap.engine.core.service630.container.ServiceRunner#######SAPEngine_System_Thread[impl:5]_51##0#0#Error#1#/System/Server#Plain###Core service security failed. J2EE Engine cannot be started.#
    #1.5#00A0D1BC74B6001E0000000E0000118C0003F7536153BD59#1116362417365#/System/Server##com.sap.engine.core.Framework#######SAPEngine_System_Thread[impl:5]_51##0#0#Fatal#1#com.sap.engine.core.Framework#Plain###Critical shutdown was invoked. Reason is: Core service security failed. J2EE Engine cannot be started.#
    Is it possible to reset the configuration back to what it was, or back to a default configuration\like in EP5 ?
    Thanks,
    Tomas.

  • Can't start weblogic Server -The server will force shutdown now

    Hello Community  ; ) , I hope i post this on the right topic if not pls advise me.
    I'm working as a trainee by a company which wants to establish OIBEE.
    I'm really new to this topic and hope i can get some help with my problems . Cause i stuck in many ways .
    I installed Oracle OBIEE 11g and the latest Patch 11.1.1.7.1.
    After changing the Oracle Logo in Oracle Home I restarted the Services, using Oracle WebLogic Server Administration Console.But it cant restart and stuck!
    So i stopped all manual using commands like "./stopWebLogic.sh ". As I wanted to start it again i get some error messages. Can somebody advise me how to handle this problem ? I would be very grateful.
    <Oct 29, 2013 12:09:31 PM CET> <Warning> <Munger> <BEA-2156203> <A version attribute was not found in element application in the deployment descriptor in /app/oracle/product/OBIEE11.1.1.7/oracle_common/atgpf/modules/oracle.applcore.model_11.1.1/oracle.applcore.model.stub.ear/META-INF/application.xml. A version attribute is required, but this version of the Weblogic Server will assume that the JEE5 is used. Future versions of the Weblogic Server will reject descriptors that do not specify the JEE version.>
    <Oct 29, 2013 12:09:32 PM CET> <Warning> <Security> <BEA-090668> <Ignored deployment of role "Admin" for resource "type=<url>, application=DMS Application#11.1.1.1.0, contextPath=/dms, uri=/">
    <Oct 29, 2013 12:09:35 PM CET> <Warning> <Connector> <BEA-190155> <Compliance checking/validation of the resource adapter /app/oracle/product/OBIEE11.1.1.7/user_projects/domains/bifoundation_domain/servers/AdminServer/tmp/_WL_user/ESSAPP/z68zjr/stub-ess-ra.rar resulted in the following warnings:
    The ra.xml <resourceadapter-class> class 'oracle.as.scheduler.adapter.ra.RAImpl' should implement java.io.Serializable but does not.>
    <Oct 29, 2013 12:24:25 PM CET> <Notice> <WebLogicServer> <BEA-000388> <JVM called WLS shutdown hook. The server will force shutdown now>
    <Oct 29, 2013 12:24:25 PM CET> <Alert> <WebLogicServer> <BEA-000396> <Server shutdown has been requested by <WLS Kernel>>
    <Oct 29, 2013 12:24:25 PM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN>

    Hi VG,
    thank u a lot for ur answer. But there are no files at the Admin Server boot.properties path.
    and at the BI Server boot.properties path there is no security folder. Do u have any idea why i cant found anything at this directions ? Also I tried again the command "./startWeblogic.sh " and get a new error message which I post below. I am rlly worry about this. Is there maybe a way to reset the OBIEE and undo all changes ?
    <Oct 30, 2013 10:00:47 AM CET> <Warning> <EJB> <BEA-010001> <While deploying EJB 'AsyncAdminService_AsyncRequestProcessorMDB', class oracle.j2ee.ws.server.jaxws.AsyncRequestProcessorMDB was loaded from the system classpath. As a result, this class cannot be reloaded while the server is running. To prevent this behavior in the future, make sure the class is not located in the server classpath.>
    <Oct 30, 2013 10:00:47 AM CET> <Warning> <EJB> <BEA-010001> <While deploying EJB 'AsyncAdminService_AsyncResponseProcessorMDB', class oracle.j2ee.ws.server.jaxws.AsyncResponseProcessorMDB was loaded from the system classpath. As a result, this class cannot be reloaded while the server is running. To prevent this behavior in the future, make sure the class is not located in the server classpath.>
    <Oct 30, 2013 10:00:48 AM CET> <Warning> <J2EE> <BEA-160195> <The application version lifecycle event listener oracle.security.jps.wls.listeners.JpsAppVersionLifecycleListener is ignored because the application em is not versioned.>
    ^C<Oct 30, 2013 10:39:50 AM CET> <Notice> <WebLogicServer> <BEA-000388> <JVM called WLS shutdown hook. The server will force shutdown now>
    <Oct 30, 2013 10:39:50 AM CET> <Alert> <WebLogicServer> <BEA-000396> <Server shutdown has been requested by <WLS Kernel>>
    <Oct 30, 2013 10:39:50 AM CET> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to FORCE_SHUTTING_DOWN>

Maybe you are looking for