XServe Upgrade failed -- system no longer accessable
I was upgading our XServe G5 running 10.4.11 to Leopard using a remote install (no video card). I accessed the system using ARD and ran the install, which of course reformats the drive. When it finished I got a pop-up window saying the installation failed. I clicked ok (my only option) and that is the last I have seen of the machine. It has disappeared from the network. Our router doesn't have the mac address in its arp table.
It looks like the only potential method of recovery is connect via the serial port and see what commands are available to try and resurrect this thing from the dead.
Has anyone seen this before?
Thanks
Just to Follow-up how the system was fixed.
1. Attached a keyboard to the system
2. Brought a old G4 laptop out of retirement and connected it the XServe G5 firewire 400 port (So that the correct processor dependent packages were picked up in the installation)
3. Power cycled the Xserve and held down the "t" key during the boot.
4. Went through the installation process using the firewire as the target disk.
5. After the reboot, connected to the ethernet with a cross-over (turned out that the wrong ethernet got configured -- of course the XServe had the interfaces configured for the G4 laptop)
6. Ran ARD in bonjour mode to find the self-assigned IP address and configured the laptop ethernet for that network.
7. Configured the static IP address on the XServe - connected it back on the network
8. Ran the leopard updates.
In all a very ugly experience, but I put this out so that others don't go through the same.
Similar Messages
-
I was just about to order a photo book, using photos stored on an external hard drive. I organised the book and pressed 'buy'. IPhotos instructed me that I needed to upgrade and so I went on the ASpp store, bought the upgrade and installed as directed. I then used the iPhoto Library upgrader as directed.
After the iPhoto upgrade I can no longer access the photos stored on my external hard drive. I am able to access the photos stored on my internal hard drive - the remainder (including the photo album) seem to have vanished into thin air.
Any suggestions please?What format is the external drive?
-
On a recent upgrade I can no longer access some Pages documents\
After an OS X update combined and then a Pages update I am no longer able to access through Pages many of my documents; any ideas out there?
You have us just guessing without any details, but chances are you updated to Pages 5.5.2 and can no longer open Pages '08 or earlier files.
You need to either export the files from Pages '08 to Word .docx or .txt files and open those in Pages 5.5.2.
Apple has failed to maintain much backwards compatibility.
Usually the older versions will still be in your Applications/iWork folder.
Peter -
Since upgrading software I no longer access Netflix
I upgraded to the latest software. Netflix is no longer available.
I had to do a restore. I tried to do this on the Apple TV, itself but this just hung up the device. Luckily I had the right USB cable so I did another restore thru iTunes. This solved the problem.
-
I recently had a firefox update (withing past 3 days). Now when I go to close down my browser it only asks me if I am sure I want to close all tabs.
Previously it had asked me if I wanted to quit and save my open tabs or just quit.You can use "Firefox > History > Restore Previous Session" to get the previous session.<br />
There is also a "Restore Previous Session" button on the default about:home Home page.<br />
Another possibility is to use:<br />
*Tools > Options > General > Startup: "When Firefox Starts": "Show my windows and tabs from last time"
You can set the warn prefs on the about:config page to true via the right-click context menu or toggle with a double left-click.
* browser.showQuitWarning, see http://blog.zpao.com/post/3174360617/about-that-quit-dialog
* browser.tabs.warnOnClose, see http://kb.mozillazine.org/About%3Aconfig_entries
* browser.warnOnQuit , see http://kb.mozillazine.org/browser.warnOnQuit
* browser.warnOnRestart , see http://kb.mozillazine.org/browser.warnOnRestart
To open the <i>about:config</i> page, type <b>about:config</b> in the location (address) bar and press the "<i>Enter</i>" key, just like you type the url of a website to open a website.<br />
If you see a warning then you can confirm that you want to access that page.<br /> -
Since having the latest upgrade I can no longer access my tiscali.e mails
Dowloaded latest version of Firefox this a.m. Now cannot access my e mails as message reads You have undefined new mails in your inbox. This has not happened before. I can however access thru Internet explorer and Outlook. Is this a problem with latest version of Firefox?????
For the third time, please post your Troubleshooting Information.<br>
This shouldn't take 3 hours.
Help (Alt-H) - Troubleshooting Information -
Once firefox completed its upgrade I can no longer access my text window/box in my yahoo mail account. Which means I cannot text from my mail account now. I cant figure out why this is happening.
Once firefox completed its upgrade I can no longer access my text window/box in my yahoo mail account. Which means I cannot text from my mail account now. I cant figure out why this is happening.
-
After upgrading to 10.7.2, can no longer access Keychain or SSL sites
During the iOS 5 / iPhone 4S launch, while waiting for my 3GS to be able to upgrade, I simultaneously upgraded my MacBook Pro from 10.7.1 to 10.7.2. As soon as I did so, I could no longer access SSL-specified URLs in any browser. Specifically, and most annoyingly, the login page for my work's guest wireless system. HTTP sites work, HTTPS sites do not, in other words. I should mention that 10.7.1 did not give me this behavior.
I tried a number of things: clearing out Safari preferences, network preferences, etc. and finally tracked it down to what seems to be a certificate issue. I am guessing this, because I cannot launch Keychain Access. It kicks off, and builds the menus, but then goes into a rainbow wheel and becomes unresponsive.
After a flurry of things I tried, including dumping my personal keychains (~/Library/Keychains) and system keychains (/Library/Keychains), resetting PRAM (don't know why that would work, but it's always suggested), removing WiFi from the connection methods under a new location in the Network preferences pane, re-establishing permissions on keychains (chmod 755) and changing ownership (chown -R), etc. I got it to work. And it worked for the entire day while I was at my job.
After returning home, working there for awhile on my WiFi there, and then coming back to work the next day - same problem. But the sequence of things I tried didn't work this time. So, I tried a bunch of other things, including the things I did the first time and got it to work a second time. There didn't seem to be a magic bullet - it always seemed like "Ah ha! That's the thing I need to do" and then after another cycle of going home and then coming back to work, that one thing had no effect and it was back to randomly shotgunning diagnostics and troubleshooting methods, including:
* Running Disk Utility from Recovery mode
* Installing a fresh copy of Lion from Recovery mode
I've watched the console, and to be honest, I may be missing something, but I can't seem to pin it down.
The main symptoms, in summary are:
* Wake computer from sleep, and my MBP connects to my guest wireless at work
* Safari cannot launch - it goes unresponsive after the icon bounces for a minute
* Chrome launches, but when trying to access SSL sites (primarily the wireless login page) it gives an ERR 7: timeout.
* If I change the https: for the login page to http: - suddenly I'm allowed to logon and get internet access. But still no SSL pages.
* Attempting to launch Keychain Access bounces the icon, the menus build, and then the program becomes unresponsive.
Has anyone seen this behavior before? I've done a lot of searching on this, and it would seem that another group of folks have a similar issue here:
http://forums.techarena.in/operating-systems/1435689.htm
Searching for "Keychain Access Not responding" and similar terms brings up some helpful stuff, but nothing that solves the problem.
Thanks in advance for any help!Hi,
I experienced similar behavior (neither Keychain Access nor Safari would start, Chrome cannot access https sites, etc.). It got fixed by following instructions in this article:
http://www.macworld.com/article/163227/2011/10/fix_a_lion_file_opening_hang_in_m ac_os_x_10_7_2.html which I found in this thread: http://att.macrumors.com/showthread.php?p=13625027#post13625027
Basically remove the ~/Library/Application Support/Ubiquity and restart. OSX will create a new one with the right permisions.
/cheers -
Failed to open the console and System Center Data Access Service wont start - SCOM 2012
Log Name: Operations Manager
Source: Data AccessLayer
Event ID: 33333
Data Access Layer rejected retry on SqlError:
Request: ManagementGroupInfo
Class: 16
Number: 208
Message: Invalid object name 'dbo.__MOMManagementGroupInfo__'.
=============================================================
Log Name: Operations Manager
Source: OpsMgr SDK Service
Event ID: 26380
The System Center Data Access service failed due to an unhandled exception.
The service will attempt to restart.
Exception:
Microsoft.EnterpriseManagement.Common.SdkServiceNotInitializedException: The Data Access service has not yet initialized. Please try again.
at Microsoft.EnterpriseManagement.ServiceDataLayer.DispatcherService.get_Container()
at Microsoft.EnterpriseManagement.Mom.Sdk.Service.SdkSubService.SdkChannel.Start()
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state)
at System.Threading._ThreadPoolWaitCallback.PerformWaitCallbackInternal(_ThreadPoolWaitCallback tpWaitCallBack)
at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback(Object state)
=============================================================
Failed to connect to server ' xxxxx'
Date: 16/09/2013 20:36:16
Application: Operations Manager
Application Version: 7.0.8560.0
Severity: Error
Message: Failed to connect to server 'xxxxxx'
Microsoft.EnterpriseManagement.Common.ServiceNotRunningException: The Data Access service is either not running or not yet initialized. Check the event log for more information. ---> System.ServiceModel.EndpointNotFoundException: Could not connect to net.tcp://xxxxx:5724/DispatcherService.
The connection attempt lasted for a time span of 00:00:02.0020300. TCP error code 10061: No connection could be made because the target machine actively refused it xxx.xxx.xxx.xxx:5724. ---> System.Net.Sockets.SocketException: No connection could
be made because the target machine actively refused it xxx.xxx.xxx.xxx:5724
at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
--- End of inner exception stack trace ---
Server stack trace:
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.BufferedConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.ConnectionPoolHelper.EstablishConnection(TimeSpan timeout)
at System.ServiceModel.Channels.ClientFramingDuplexSessionChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.CallOnceManager.CallOnce(TimeSpan timeout, CallOnceManager cascade)
at System.ServiceModel.Channels.ServiceChannel.EnsureOpened(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.Call(String action, Boolean oneway, ProxyOperationRuntime operation, Object[] ins, Object[] outs, TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannelProxy.InvokeService(IMethodCallMessage methodCall, ProxyOperationRuntime operation)
at System.ServiceModel.Channels.ServiceChannelProxy.Invoke(IMessage message)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at Microsoft.EnterpriseManagement.Common.Internal.IDispatcherService.Connect(SdkClientConnectionOptions connectionOptions)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.Initialize(EnterpriseManagementConnectionSettings connectionSettings, SdkChannelObject`1 channelObjectDispatcherService)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.CreateEndpoint[T](EnterpriseManagementConnectionSettings connectionSettings, SdkChannelObject`1 channelObjectDispatcherService)
--- End of inner exception stack trace ---
at Microsoft.EnterpriseManagement.Common.Internal.ExceptionHandlers.HandleChannelExceptions(Exception ex)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.CreateEndpoint[T](EnterpriseManagementConnectionSettings connectionSettings, SdkChannelObject`1 channelObjectDispatcherService)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.ConstructEnterpriseManagementGroupInternal[T,P](EnterpriseManagementConnectionSettings connectionSettings, ClientDataAccessCore clientCallback)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.RetrieveEnterpriseManagementGroupInternal[T,P](EnterpriseManagementConnectionSettings connectionSettings, ClientDataAccessCore callbackDispatcherService)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.Connect[T,P](EnterpriseManagementConnectionSettings connectionSettings, ClientDataAccessCore callbackDispatcherService)
at Microsoft.EnterpriseManagement.ManagementGroup.InternalInitialize(EnterpriseManagementConnectionSettings connectionSettings, ManagementGroupInternal internals)
at Microsoft.EnterpriseManagement.Mom.Internal.UI.Common.ManagementGroupSessionManager.Connect(String server)
at Microsoft.EnterpriseManagement.Monitoring.Console.Internal.ConsoleWindowBase.TryConnectToManagementGroupJob(Object sender, ConsoleJobEventArgs args)
System.ServiceModel.EndpointNotFoundException: Could not connect to net.tcp://xxxxx:5724/DispatcherService. The connection attempt lasted for a time span of 00:00:02.0020300. TCP error code 10061: No connection could be made because the target machine actively
refused it xxx.xxx.xxx.xxx:5724. ---> System.Net.Sockets.SocketException: No connection could be made because the target machine actively refused it xxx.xxx.xxx.xxx:5724
at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
--- End of inner exception stack trace ---
Server stack trace:
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.BufferedConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
at System.ServiceModel.Channels.ConnectionPoolHelper.EstablishConnection(TimeSpan timeout)
at System.ServiceModel.Channels.ClientFramingDuplexSessionChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.CallOnceManager.CallOnce(TimeSpan timeout, CallOnceManager cascade)
at System.ServiceModel.Channels.ServiceChannel.EnsureOpened(TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannel.Call(String action, Boolean oneway, ProxyOperationRuntime operation, Object[] ins, Object[] outs, TimeSpan timeout)
at System.ServiceModel.Channels.ServiceChannelProxy.InvokeService(IMethodCallMessage methodCall, ProxyOperationRuntime operation)
at System.ServiceModel.Channels.ServiceChannelProxy.Invoke(IMessage message)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at Microsoft.EnterpriseManagement.Common.Internal.IDispatcherService.Connect(SdkClientConnectionOptions connectionOptions)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.Initialize(EnterpriseManagementConnectionSettings connectionSettings, SdkChannelObject`1 channelObjectDispatcherService)
at Microsoft.EnterpriseManagement.Common.Internal.SdkDataLayerProxyCore.CreateEndpoint[T](EnterpriseManagementConnectionSettings connectionSettings, SdkChannelObject`1 channelObjectDispatcherService)
System.Net.Sockets.SocketException (0x80004005): No connection could be made because the target machine actively refused it xxx.xxx.xxx.xxx:5724
at System.Net.Sockets.Socket.DoConnect(EndPoint endPointSnapshot, SocketAddress socketAddress)
at System.Net.Sockets.Socket.Connect(EndPoint remoteEP)
at System.ServiceModel.Channels.SocketConnectionInitiator.Connect(Uri uri, TimeSpan timeout)
=============================================================
Log Name: Operations Manager
Source: OpsMgr Root Connector
Event ID: 28001
The Root connector received an exception from the Config Service on StateSyncRequest:
System.Runtime.Remoting.RemotingException: Failed to connect to an IPC Port: The system cannot find the file specified.
Server stack trace:
at System.Runtime.Remoting.Channels.Ipc.IpcPort.Connect(String portName, Boolean secure, TokenImpersonationLevel impersonationLevel, Int32 timeout)
at System.Runtime.Remoting.Channels.Ipc.ConnectionCache.GetConnection(String portName, Boolean secure, TokenImpersonationLevel level, Int32 timeout)
at System.Runtime.Remoting.Channels.Ipc.IpcClientTransportSink.ProcessMessage(IMessage msg, ITransportHeaders requestHeaders, Stream requestStream, ITransportHeaders& responseHeaders, Stream& responseStream)
at System.Runtime.Remoting.Channels.BinaryClientFormatterSink.SyncProcessMessage(IMessage msg)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at Microsoft.EnterpriseManagement.Mom.Internal.IConfigService.OnStateSyncRequest(Guid source, UInt64 messageIdentifier, String cookie)
at Microsoft.Mom.Connectors.Root.RootConnector.OnStateSyncRequest(Guid source, UInt64 messageIdentifier, String cookie)
================================================================
Log Name: Operations Manager
Source: OpsMgr Management Configuration
Event ID: 29105
The management group is not yet fully upgraded. OpsMgr Management Configuration Service will idle until upgrade is completed.
Operations Manager database version: 1.0.0.0
Minimum required version: 7.0.0.0Yes, i change the credentials, but doesnt work.
Yes, i put the events in the
main question!
Events Logs:
=======================================================
Log Name: Operations Manager
Source: Data AccessLayer
Event ID: 33333
Data Access Layer rejected retry on SqlError:
Request: ManagementGroupInfo
Class: 16
Number: 208
Message: Invalid object name 'dbo.__MOMManagementGroupInfo__'.
=======================================================
Log Name: Operations Manager
Source: OpsMgr SDK Service
Event ID: 26380
The System Center Data Access service failed due to an unhandled exception.
The service will attempt to restart.
Exception:
Microsoft.EnterpriseManagement.Common.SdkServiceNotInitializedException: The Data Access service has not yet initialized. Please try again.
at Microsoft.EnterpriseManagement.ServiceDataLayer.DispatcherService.get_Container()
at Microsoft.EnterpriseManagement.Mom.Sdk.Service.SdkSubService.SdkChannel.Start()
at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state)
at System.Threading._ThreadPoolWaitCallback.PerformWaitCallbackInternal(_ThreadPoolWaitCallback tpWaitCallBack)
at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback(Object state)
=======================================================
Log Name: Operations Manager
Source: OpsMgr Root Connector
Event ID: 28001
The Root connector received an exception from the Config Service on StateSyncRequest:
System.Runtime.Remoting.RemotingException: Failed to connect to an IPC Port: The system cannot find the file specified.
Server stack trace:
at System.Runtime.Remoting.Channels.Ipc.IpcPort.Connect(String portName, Boolean secure, TokenImpersonationLevel impersonationLevel, Int32 timeout)
at System.Runtime.Remoting.Channels.Ipc.ConnectionCache.GetConnection(String portName, Boolean secure, TokenImpersonationLevel level, Int32 timeout)
at System.Runtime.Remoting.Channels.Ipc.IpcClientTransportSink.ProcessMessage(IMessage msg, ITransportHeaders requestHeaders, Stream requestStream, ITransportHeaders& responseHeaders, Stream& responseStream)
at System.Runtime.Remoting.Channels.BinaryClientFormatterSink.SyncProcessMessage(IMessage msg)
Exception rethrown at [0]:
at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
at Microsoft.EnterpriseManagement.Mom.Internal.IConfigService.OnStateSyncRequest(Guid source, UInt64 messageIdentifier, String cookie)
at Microsoft.Mom.Connectors.Root.RootConnector.OnStateSyncRequest(Guid source, UInt64 messageIdentifier, String cookie)
=======================================================
Log Name: Operations Manager
Source: OpsMgr Management Configuration
Event ID: 29105
The management group is not yet fully upgraded. OpsMgr Management Configuration Service will idle until upgrade is completed.
Operations Manager database version: 1.0.0.0
Minimum required version: 7.0.0.0 -
Following upgrade to 34.05, can no longer access web pages of the SAN management interface, the airco system, the vSphere Web Client, etc. All still work in Chrome.
The airco system gives an error:
Firefox cannot guarantee the safety of your data on 10.32.16.50 because it uses SSLv3, a broken security protocol.
Advanced info: ssl_error_no_cypher_overlap
The SAN management interface and vSphere Web Clients display an empty page. Not sure whether these also have problems due to SSLv3.
I understand you wanting to be cautious, but I seriously doubt I need to face an attack from our SAN. Please, at least give us an option to connect regardless.hello, ssl 3.0 is disabled in firefox versions 34 & upwards by default - if you want to re-enable it you can do that like this which will make you vulnerable to the recently published poodle attack though:
enter '''about:config''' into the firefox address bar (confirm the info message in case it shows up) & search for the preference named '''security.tls.version.min'''. double-click it, change its value to '''0''' and restart the browser.
https://blog.mozilla.org/security/2014/10/14/the-poodle-attack-and-the-end-of-ssl-3-0/ -
On Windows 7 PC, got the "upgrade iTunes" notice this morning, said sure, but the upgrade failed, now I can't access iTunes "invalid permissions"
I wasn't paying attention so I don't know the precise error I got on the upgrade failure.
All other iTunes upgrades have been fine...no brainers. Done several on this W7 PC.
If I re-download and install a fresh iTunes I assume I will lose my library...true? Can I find and save off my library so I don't have to "discover" all my music which is scattered all over the PC and a 1T attached USB drive.
Or is there some way to get the iTunes upgrade to successfully restart and install correctly?
Help!Hello there, Konami84.
The following Knowledge Base article provides some recomendations for troubleshooting:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Check for .dll files
Go to C:\Program Files (x86)\iTunes and C:\Program Files\iTunes and look for .dll files.
If you find QTMovie.DLL, or any other .dll files, move them to the desktop.
Reboot your computer.
Note: Depending on your operating system, you may only have one of the listed paths.
Uninstall and reinstall iTunes
Uninstall iTunes and all of its related components.
Reboot your computer. If you can't uninstall a piece of Apple software, try using the Microsoft Program Install and Uninstall Utility.
Re-download and reinstall iTunes 11.1.4.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
I can no longer access my iCloud calendar on my MS based computer. I am running Windows 2007 and use MS Outlook 2003. This issue just happened after I updated my iPhone operating system. What do I need to do?
http://support.apple.com/kb/dl1455
Microsoft Outlook 2007 or later or an up-to-date browser is required for accessing email, contacts, and calendars. -
I can no longer access listing variations in Ebay after the upgrade
After upgrading my Firefox on 3.01.2012 I can no longer access listing variations or change prices on these Ebay listings. Other edits within the site seem unaffected.
Well, just imported all of my settings into Google Chrome. Been nice knowing you Firefox.
-
Exchange 2010 SP2 to SP3 upgrade fails on Client Access Role
Hello,
I have searched everywhere and cannot find any answer to my problem. We have 1 Exchange server with all 3 roles installed and during the upgrade from SP2 to SP3 the server fails during the Client Access Role with the following error:
Error:
The following error was generated when "$error.Clear();
Get-ClientAccessServer $RoleFqdnOrName | Add-AdPermission -User "S-1-5-20" -ExtendedRights "Exchange Web Services Token Serialization";
" was run: "Invalid URI: The format of the URI could not be determined.".
Invalid URI: The format of the URI could not be determined.
Click here for help... http://technet.microsoft.com/en-US/library/ms.exch.err.default(EXCHG.141).aspx?v=14.2.247.1&e=ms.exch.err.Ex88D115&l=0&cl=cp
here is more info from the ExchangeSetupLogs
[10/09/2014 09:26:07.0463] [1] Executing:
Get-ClientAccessServer $RoleFqdnOrName | Add-AdPermission -User "S-1-5-20" -ExtendedRights "Exchange Web Services Token Serialization";
[10/09/2014 09:26:07.0463] [2] Active Directory session settings for 'Get-ClientAccessServer' are: View Entire Forest: 'True', Configuration Domain Controller: 'ADROOT.DOMAIN.local', Preferred Global Catalog: 'ADROOT.DOMAIN.local', Preferred Domain Controllers:
'{ ADROOT.DOMAIN.local }'
[10/09/2014 09:26:07.0463] [2] Beginning processing Get-ClientAccessServer -Identity:'EXCH2010.DOMAIN.local'
[10/09/2014 09:26:07.0463] [2] Active Directory session settings for 'Add-ADPermission' are: View Entire Forest: 'True', Configuration Domain Controller: 'ADROOT.DOMAIN.local', Preferred Global Catalog: 'ADROOT.tioh.local', Preferred Domain Controllers: '{
ADROOT.DOMAIN.local }'
[10/09/2014 09:26:07.0463] [2] Beginning processing Add-AdPermission -User:'S-1-5-20' -ExtendedRights:'Exchange Web Services Token Serialization'
[10/09/2014 09:26:07.0479] [2] Searching objects "EXCH2010.DOMAIN.local" of type "Server" under the root "$null".
[10/09/2014 09:26:07.0479] [2] Previous operation run on domain controller 'ADROOT.DOMAIN.local'.
[10/09/2014 09:26:07.0479] [2] Previous operation run on domain controller 'ADROOT.DOMAIN.local'.
[10/09/2014 09:26:07.0479] [2] Preparing to output objects. The maximum size of the result set is "unlimited".
[10/09/2014 09:26:07.0510] [2] [WARNING] An unexpected error has occurred and a Watson dump is being generated: Invalid URI: The format of the URI could not be determined.
[10/09/2014 09:26:07.0526] [2] [ERROR] Invalid URI: The format of the URI could not be determined.
The article it references doesn't exist and I cannot find anything related to this error searching the web.
Please help!
NJVHi NJv7300
Thank you for your question.
By your state, I know you get error when you use Get_ClientAccessServer. I think it caused by AutoDiscover, you can check it.
You can refer to the following link:http://www.shudnow.net/?s=autodiscoverserviceinternaluri
You can refer to the following steps:1.
1. Using LDP, locate the following container:
CN=<SERVERNAME>,CN=Autodiscover,CN=Protocols,CN=<SERVERNAME>,CN=Servers,CN=Exchange Administrative Group (FYDIBOHF23SPDLT),CN=Administrative Groups,CN=<ORGNAME>,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=<DOMAIN>,DC=<TLD>
2. Double-click the <SERVERNAME> under Autodiscover and look for the "serviceBindingInformation" value:serviceBindingInformation (2): AutoDiscover.Corp.HMSA.com;
https://honmail.corp.hmsa.com/autodiscover/autodiscover.xml;
serviceClassName: ms-Exchange-AutoDiscover-Service;The proper format for the Autodiscover URI is
https://serverfqdn/Autodiscover/Autodiscover.xml
3. Ran Set-ClientAccessServer -Identity HON10343 -AutodiscoverServiceInternalUri
https://honmail.corp.hmsa.com/autodiscover/autodiscover.xml
4. Ran Get-ClientAccessServer, but received an error after HON10343 was enumerated.
5. Next, did another Set-ClientAccessServer on HON10344.
6. Finally, ran Get-ClientAccessServer and enumerated all CAS servers in the org without error.
7. Tested opening EMC on both Exchange 2007 and 2010 and were able to successfully expand the Server Configuration for every role and enumerate all servers.
If any questions, please let me know.
Best Regard,
Jim Xu -
I upgraded to PhotoShop CC 2014 and can no longer access my NIK Collection. It worked fine in PhotoShop CC? What can I do?
Contact Nik/Google for updated plugins that work in the new version of Photoshop.
Maybe you are looking for
-
Starting computer only. Blue screen appears, how do I resolve this?
I recently had to upgrade my hard drive on my MacBook pro 13 inch 2010. I reinstalled my back up from time machine and performed an update. Aft that it has not worked and only displays a blue screen and nothing else. Does anyone have any suggestion
-
Hi, I am using Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 . I am working in a procedure where I want to manipulate the data produced by a WITH AS clause. But it is giving "PL/SQL: ORA-00942: table or view does not exist" error. A smal
-
Does anyone know when there will be Camera Raw Support in Lightroom 3 for the Olympus E-PL2?
Just bought the Olympus E-PL2, shot some test shots and came home to open my RAW files to view them and discovered that they won't open in lightroom because the .ORF files for the E-PL@ are not supported. I figured since the E-PL1 was supported this
-
Why do server.app crash sometimes? Can I use it this way as a router?
Hi everyone! I have a problem, sometimes the server.app crash, I don't know why. The Mac OS system do not crash, It's just the server.app. You can se the crash logg in the buttom of this post, I have three logg files. I also have an other quastion, I
-
I have MS Visual Studio Express 2013 It has worked fine for many months and then suddenly (I have made no configuration changes or added new programs) when I try to publish I am getting the message: Unable to create the Web site 'ftp://ftp.xx.xx/xxx.