Yet another boot problem

I swear this piece of crap is inches from the dumpster. I have spent the last week fixing problems that I thought I had already fixed.
The latest is that I am back to taking about 5 minutes to boot up. It hangs right after listing the BIOS version but before finding the processor, then it hangs again between the windows logo and the desktop. This appears to occur regardless of whether there are usb devices attached, so it's different from the last bott problem we all had.
This started with a black screen of death, which I fixed using anakin's (i think?) solution. As anakin suggested I reinstalled the drivers i could find directly from MSI's site, not thru Live Update. I then went to nvidia, and got the vga drivers. The first few times I booted, I thought I was home free when it came right up like old times, now here i am again.
Questions:
1. What do I look for to identify the hangs at those times during boot?
2. Can someone give me the correct driver versions so I can be sure I didn't pull the wrong ones?
3. Slightly unrelated- should I uninstall Live Update, as I have no need for it to give me drivers that cause these problems?
as always, thanks in advance

Now it doesn't shut down at all. Hoo-freakin'-ray!
I have been at a wedding drinking for several hours, so at least I'm jovial about it now. However right before I left, I rebooted, everything came up beautifully, but when I went to shut down, i got more hang time than michael jordan. the beauty part is, do you want to know the changes I made? Abso-f'ing-lutely nothing. In other words, having changed no settings/drivers/etc., my problem went from no boot, to no shut down. MSI should go f itself as often as possible.
I can solve all of these issues with enough diligence. What irks me is the fact that I have spent the last week trying to fix a problem that changes with the breeze. Who was the idiot at MSI that said "yup, this is the best we can do. ship 'em!"
Now that I have ranted, does anyone else have a shutdown problem?

Similar Messages

Sorry, but another boot problem

I am sorry to ask this question but I have read all of the recent posts on boot problems and followed all instructions but I am still having a problem. It passes the POST then gives the Boot Failure, insert boot disk into drive A message. The only thing I have not done is install a new bios. I have only got one SATA HDD, one CD Writer and floppy.
I have plugged the HD into SATA1 and the CD into IDE1, during the boot sequence it see the CD as Primary Master1 and the HDD as Third IDE Master.
During the POST it passes memory test and can detect both the HDD and CD and floppy.
I have set the HDD settings as follows:
Native Mode
ATA Config= S-ATA only
S-ATA keep enabled = Yes
P-ATA keep enabled = Yes
P-ATA Channel Selection = Both
Combined Mode = S-ATA 1st channel
S-ATA ports definition = P0-1st/P1-2nd
Also I have set the Boot sequence as follows:
1st boot = CD
2nd boot = HDD
3rd boot = floppy
I have built this PC only in the last few days and there is no operating system yet, it has the following specs:
BIOS A6728IMS 3.5 020504
865PE Neo2
Pentium 4 2.40aGhz
2 x 256 Kingston 400Mhz PC3200
128MB Excalibur RADEON 9200 8xAGP
Seagate 80Gb S-ATA HDD
LiteOn 52x CD Writer
PSU: 3.3v 28A, 5v 32A, 12v 16A (350W)
Any help would be greatly appreciated.
Thanks

Thanks, its good to know that I seem to have set it up ok but when I try to boot from the cd (Windows Server 2003) it still says there is a boot failure please insert disk into drive A???
Adam
BIOS A6728IMS 3.5 020504
865PE Neo2
Pentium 4 2.40aGhz
2 x 256 Kingston 400Mhz PC3200
128MB Excalibur RADEON 9200 8xAGP
Seagate 80Gb S-ATA HDD
LiteOn 52x CD Writer
PSU: 3.3v 28A, 5v 32A, 12v 16A (350W)

YAPP (Yet Another Printing Problem)

I've found another printing problem - this time with colour printing.
To my
surprise, Forte (3.0.E.0) can print in colour (at least on a HP 690C,
using
NT drivers for the 660C, the printer being connected to a Win95
machine).
I can print OK with from my NT develpoment machine in colour, but when
running
the same app from the Win95 client with the printer attached locally the
coloured text disappears. Has anyone else come across this problem?
Is this another of the 'Printing works fine as long as it happens
non-locally?'
features?
Thanks
Jamie Anstice
Programmer/Analyst, University of Canterbury
New Zealand

I can print OK with from my NT develpoment machine in colour, but when
running
the same app from the Win95 client with the printer attached locally the
coloured text disappears. Has anyone else come across this problem?Hi Jamie,
I wonder if this is related to the printing feature I discovered
where things I print from Forte have a strong tendency to come out in
the same colours as my windows desktop, which is
typically yellow-on-black.
- Ed
================================================================================
Eduard E Havelaar, Information Services Section, University of Canterbury
email: [email protected]
phone: +64-3-366 7001 extn 8910
fax: +64-3-364 2999
snailmail: Private Bag 4800, Christchurch, New Zealand

IPod Touch (yet another) syncing problem contacts, address book

I have a new 2nd gen Touch 8g. I am trying to sync to my MacBook Pro. Would like to sync all my contacts and calendar info from my old Palm, but that is not my question today. I am unable to sync my Address Book and iCal information to Contacts and Calendar on the Touch. Specifics:
- OS X is 10.5.6
- iTunes is 8.1, recently updated
- iTouch software is 2.2.1, recently updated
- Address Book is 4.1.1
- iCal is 3.0.6
I can "sync" using iTunes. It backs up the Touch. It syncs the music. It doesn't sync the Address Book or Contacts properly.
History:
- At first, I set it to sync the Address Book and Contacts (not Calendar and iCal). It would go through the sync process until "Updating Contacts with..." It would hang there overnight. This happened when there were 200+ contacts in Address Book on the Mac but none on the Touch. I cancelled after overnight hours and found none on the Touch.
- Deleted all Address Book contacts. Now there were none on either Mac or Touch. Still would spin the "Updating Contacts with..." for hours.
- Set iTunes to sync both Address Book and iCal. Added 1 simple contact in Address Book. Added 1 event in iCal. Synced. The sync completed but nothing was transferred between the Mac and the Touch.
- Added 1 contact in Contacts on Touch and 1 event in Calendar on Touch. Synced. Each still had 1 contact, 1 event, but not the same ones.
- Set iTunes to replace the information on the iPod (one time). The sync completed, and erased the contact and calendar event on the Touch, and put the 1 iCal event onto the Touch (yea!) but not the contact from Address Book (boo!).
- Tried multiple more times. I can add a calendar event on the Touch, but it never appears on iCal on the Mac. I can add a contact on the Touch or in Address Book on the Mac, but the two never sync up to show on the other.
Other details:
- I don't use Google Contacts or Calendar
- I don't use MobileMe (or really know what it is yet)
- I did use iSync to try to sync all my Palm info (not successfully), but stopped trying and reset the sync history, just in case.
- I don't use USB hubs, and I do the sync with just the Touch attached via the cable it came with directly into the MacBook Pro.
- I've read hundreds of posts here and elsewhere. I've restarted programs multiple times. I've updated software. I've tried following the advice of all the posts I could, even if they weren't precisely what I was experiencing.
Does anyone have any brilliant ideas as to what I should try next? I bought this thing to replace my Palm as my PDA, but it won't be any good unless I can sync the darn thing. I've been working on this for almost 3 days straight and am going bug eyed reading all the info on the web. ANY help would be appreciated!
Thanks!

I managed to get the sync to work after much shutting down and restarting, of programs and the computer. I cleared the iSync history just in case. I closed programs, etc. Eventually, it just worked and has continued to do so ever since. It is not slow, but rather quick.
All is well.
Now, the conversion from Palm is another story.....

Yet another printing problem 'EOF' errors

This problem is probably both a Leopard and Adobe problem combined. It's a rather complicated problem, but the bottom line is that (to most printers) the jobs coming out of one of our Mac Pros cause the printers to crash and restart themselves giving an 'EOF Error (End of File)' on at least one of them. The problem also appears to affect PDF documents created in InDesign which will then cause the same errors on any computer it is printed from.
Things you may need to know and that I've already tried:
• The same printers with the same drivers printing the same files will work on other Mac Pros of the same version with the same version of Leopard.
• Using a generic driver will print properly, however this is not a workaround because we need duplexing provided by the driver and I'm not sure how this could fix the PDF problem.
• Fonts have been disabled and checked with Font Doctor.
• Starting up in 'Safe Mode' will allow printing, but without fonts or links on server volumes.
• Switching the hard drive with another identical Mac Pro brought the problem with the HD, worked on other. In other words, the problem is definitely in the software and not a hardware problem.
• Reset the printing system numerous times.
• Re-installed the OS, Adobe CS3, and a couple of documents - same problem with no added extensions. Other computer with tons of extensions and fonts, etc. - no problem.
• Plain text documents print fine.
• Some PostScript documents will print, but rarely.
• Will not print to HP LaserJet 2420, Minolta Di650 Fiery, ABDick Platemaker.
• WIll print to Kodak DigiMaster (three different models and versions)
Everything that I think sounds like it could be the problem is disproved by the fact that several other Mac Pros with the exact same configuration have no problem. I'm thinking about cloning another Mac Pro system that works and seeing if I can go about it that way.
Apple support was no help. Nor was Adobe. They tried to be helpful, but there is no logic to solving this one. This has been going on for over a week now and I've tried so many things. It's driving me crazy. Any help would be greatly appreciated.

It was actually just a commonly used font that had gone bad somehow. Problems like that are always fonts or links. Sometimes they just aren't as obvious. We thought we'd checked everything and it affected so many of her files because she used the font so often.

Wine and yet another font problem

So I upgraded my system (had to load lots of stuff, Xorg, Wine, the kernel..) and now my Wine fonts look like this:
http://koti.kapsi.fi/anpurola/winecfg.png
Some fonts are ok, but most of them are unreadable. I mostly run poker clients. I tried to delete my .wine directory, and install fonts again with winetricks, didn't help.
Does this have something to do with the new Xorg? I had to remove RgbPath and AutoAddDevices from xorg.conf BTW, to get it work.
Last edited by strummer (2008-12-08 12:12:31)

LTSmash wrote:
strummer wrote:
sunday wrote:
I've found this help:
Using wine over remote X11 sessions and No text or damaged text displayed
Please make sure not have added any fonts to wine. Font conflicts can sometimes cause a similar issue. If a fresh wine prefix.(A copy of wine that nothing has been done to yet) Is having this problem. Try setting following in registry
[HKEY_CURRENT_USER\Software\Wine\X11 Driver]
"ClientSideWithRender"="N"
Place above in text file and it can be inserted into registry by "regedit settings.txt".
This was report as been required of OS X on the 1 Dec 2007. This may change. Please apply only as required.
but it doesn't work for me. Anybody has an idea how to do it?
Wow it works! Thank you! Too bad if some of you still have problems.. BTW I'm using nvidia-96xx driver.
edit: Now that I tried different programs, I noticed some of the graphics won't work For example, I don't see any buttons in programs such as Spotify or Full Tilt Poker client..
Whoa thanks. It worked for me too.
how you ran regedit?
Last edited by na12 (2008-12-31 10:46:54)

Yet Another NVIDIA Problem(TM)

Since I updated XFree86 a week or so ago, it just keeps failing to initialise the NVIDIA module. I tried X.Org, which does exactly the same. Looking at the log, everything seems to start up properly with no errors, but suddenly it decides to give up, no reason given.
I have just discovered that if I uninstall, reinstall and modprobe the the NVIDIA drivers, it works! Until I reboot. Then, no matter what I try, it will not work at all! So I have to uninstall, reinstall and modprobe each time I reboot.
Very weird is all I can say.

Well, I had done that, but the point was that once I restarted, whether the nvidia modules was loaded by /etc/rc.sysinit or manually with modprobe, it would not work (but modprobe did not report any errors). The /dev/nvidia* devices do not show up.
Seems the problem is with UDev (maybe I needed to configure something for it?). I have switched back to DevFS for now, and it works again (X.Org). I had forgotten when I posted that I had also switched to UDev at the same time...
I still have another slightly related problem. I recently (yesterday) had this idea that maybe I should try get my (hardly ever used) Lucent winmodem working under Linux for the odd times I use dial-up. Drivers were easy to find (http://linmodems.org/). This worked under UDev, but then stopped working when I restarted (grr), the same as NVIDIA, whether they were in MODULES or whether I modprobe'd 'em. I actually got KPPP to dial on /dev/modem and it would have authorised had I bothered to configure PPP daemon first ;-) Didn't work under DevFS either, even though the install script had added a rule in /etc/modprobe.conf to alias /dev/modem which doesn't materialse. The device does appear at /dev/tts/LTM0 but KPPP can't dial on it.

[nForce] Help with another booting problem with the MSI K7N2

Ok, I've been reading the threads and tried almost all of the solutions to no avail. Here is the issue...
While adjusting speed in bios, Upon reboot the system would not display video. Steps taken to solve:
*Betwwen all changes I unpluged all power from system
1. Cleared CMOS VIA Jumper, Turned system on, no change
2. set J10 Jumper to default then restarted, Still no video.
3. Checked & reseated memory & CPU. Still nothing.
4. Removed battery for about 30 seconds (Am going to try to remove it for 30 mins when i get a chance tomorrow) still nothing
At this point i assum the motherboard was bad. I tested botting up with no memory in an attempt to get the warming/error beeps but nothing the system just idles.
Am i missing something? Any help suggestions or links to solutions would be greatly appretiated.
Badtaste2k
[email protected]

Sorry, I wasn;t trying to be vague, Was messing with the comp for a couple hours and got fed up. You were right, it was the k7n2. It's not mine it's a friends and wasn't around so i was going by memory. It had been running descent but was never properly installed (software) and was poorly cooled (hardware) so it had overheating restart issues. This is where I come in. I told my friend i would take a look at his computer. It was home built by one of his friends. Te system is fairly basic and the only plug in card used is a agp video card. The computer was working great after i reinstalled the CPU with proper thermal conducting when in BIOS his Athlon 2.6 was set for 1.8 I adjusted it up to the proper setting and he asked if i could bump it further. I attempted but it was unsuccessful and didn't boot. I cleared cmos with the jumper and it booted up again no problem. I stupidly went back in a fiddled around some more with something i shouldn't have because i don't remeber what it was. I belive it was the FSB Speed, but i'm not positive what change cause this particular shutdown. I'm no computer technichian, just a hobbiest. I cleared the Jumper again but this time it dodn't come back and boot. I then looked in the book and found out about jumper 10 (i think) for the SAFE MODE 100mhz boot. I set it as well with no response. I then disconnected the power cable from the PSU and unluged the battery for about half a min or so. cleared teh cmos jumper again, kept the safe mode jumper in safe mode and tried to reboot. It still just hangs. No screen, so Bios check or wrning beeps. It just idles. It revs the hard drive up for about 20sec or so but that is it. I'm going to try the suggestion earlier in the eact oprder giving by osnavi for the reseting cmos. I tried those steps in vvaroius orders 5 or 6 times before giving up.
Any help is appretiated. Thanks for your responses.
Badtaste2k

Can you please help with yet "another" Sync problem?

I have recently changed from windows xp. I have a new computer with windows 7 and I loaded Itunes 10. There have been nothing but problems with my 5th gen nano since I have changed to my new computer.
I am unable to sync new songs; In the device section, if I click on
MUSIC; I get an error; "are you sure you want to sync music? all existing content on the Ipod will be removed and replaced with songs and playlists from your Itunes library.
It has been frustrating, because I would like to add my playlists and sync automatically and for some reason, I am not able to. Thank you for any light you may be able to shed on this situation; Tawney.

To Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact
Note: iTunes Gift Cards are only Valid in Country of issue

Yet another network problem (SIOCADDRT: No such process)

After IP address of router in my apartment changed I have troubles with bringing up my network connection. I changed my gateway address and now it fails with:
:: Starting Network [BUSY]
SIOCADDRT: No such process
[FAIL]
however
$route add <gateway ip> eth0
temporarily solves the problem:
[dreamer_@dream02 ~]$ sudo /etc/rc.d/network start
:: Starting Network [DONE]
any ideas how should I repair this to start my network automatically?

dreamer_ wrote:
rc.conf:
lo="lo 127.0.0.1"
eth0="eth0 192.168.3.128 netmask 255.255.255.0 broadcast 192.168.3.255"
INTERFACES=(lo eth0)
gateway="default gw 80.48.72.175"
ROUTES=(gateway)
the only thing that changed is gateway ip (previous was 192.168.13.something). I was playing with different netmasks and broadcast ranges but it didn't help
The problem is in the lines:
gateway="default gw 80.48.72.175"
ROUTES=(gateway)
If you are using DHCP the line ROUTES=(gateway) should read ROUTES=(!gateway) <-- notice the !
Hope this helps.
R.

Yet Another modelsUnderRay Problem!

Hi,
I've seen a few posts about using the modelsUnderRay for
collision detection but none of them have seem to help me. I've got
a complex scene and adding collision detection to my character.
However for some reason director crashes when I render the movie. I
made sure the ray is not detecting the character which it has been
added to. Heres the code I using...
collisionList =
pScene.modelsUnderRay(pCharBoundingBox.worldPosition +
vector(1,1,1) , pCharacter.transform.yAxis,#detailed )
As you can see the starting position of the ray is not the
character position. And the collisionList is empty when its not
detecting any objects, but director still crashes
I have followed this tutorial to help get me here:
http://www.fbe.unsw.edu.au/learning/director/3D/environment/collision2.asp
Has anyone has any similar problems using modelsUnderRay
before? Is there a better way for doing collision detection other
than the method the tutorial shows you for more complex scenes?
Thanks in advance for any suggestions

Don't think you have answered my question.
USB2 Enhanced Controller has 5 driver files listed
usbehci.sys
usbhus.sys
usbport.sys
hccoin.dll
usbui.dll
4xUSB Controllers each have 4 driver files listed
usbhub.sys
usbport.sys
usbuhci.sys
usbui.dll
5xUSB Root Hub each have two driver files listed
usbd.sys
usbhub.sys
That is what I am trying to confirm - is all this correct or have I some driver files there that are perhaps not current and/or not required?

Yet another internet problem after updating to Leopard

After 3 attempts, I've finally got Leopard installed on my Macbook Pro (just over 18 months old, was running Tiger perfectly well) and i STILL can't get internet access.
The Airport says its connected but nothing loads at all - it won't send/receive messages, it won't load webpages, it just sits there doing nothing until eventually (often after half an hour or more) it'll tell me that the connection has timed out.
I've done the following changes as suggested elsewhere on the internet -
1. Changed IPv4 settings to manual and doublechecked these are correct - they weren't the first time round, it was inventing phantom numbers and confusing my router for the actual interwebs. So changed that.
2. Turned IPv6 to Off on both airport and ethernet
3. corrected DNS entries for the Airport - again left to its own devices it thinks the router's IP address is the DNS address. So I added the correct 2 plus the two from Open DNS for good measure. I've tried different combinations of all 4, only the router two, only the open DNS 2 and so on and so forth and it still won't work!
4. tried restarting several times after each change.
5. double checked i don't have any of the .plist files from Tiger that might be interfering.
6. checked for a trojan horse
7. checked my router is working (it is).
And, nothing worked. It's still rubbish and does nothing. I wish I had never spent the money on the stupid upgrade and am never going to do it again!
Can anyone help?!
I've got 10.5.4 and then I patched it with the 10.5.5 Combo update too. I went for an Erase and Install option too. I'm not the most mac savvy person around, so please be gentle!
TIA.

I've checked, double checked, triple checked, tested, quadruple checked... My router is working perfectly, it works with my blackberry, friends laptops, my PC... just not my Mac. All the addresses are correct - left to its own devices the laptop with Leopard on it will NOT use the correct info for the DHCP or any other address. It uses incorrect information, confusing the Router itself with the actual internet (basically all the address fields that are meant to point you at, like, "the internet" will instead just point you to the router and the router of course replies with Hey man, whaddya want? I'm just a router... so nothing happens). Changing that gave me some internet access where previously it wasn't getting any. But all webpages take forever to load - often not loading at all - and after about 10 minutes of occasionally working the whole thing will pack up.
I flat out refuse to fork out £300 for a new router just because Apple decided to make their new OS incompatible with anything but Time Capsule (as I suspect is probably the case given loads of people are having the same problems and there's been a noticeable silence on the subject from Apple). So I guess I'll be wiping the macbook AGAIN and reinstalling Tiger from the recovery disc.
Next computer - back to a windows PC! I'm sure Microsoft are loving Leopard.

Another booting problem

Hey there,
after reading some of the related posts I'm still pretty confused and with some of them out of date I'm not sure where I stand. The phone crashed yesterday and I need to try and rescue video of my godson's first steps which wasnt backed up!
It had half battery at the time. It has rebooted by itself in the past but dunno how often as I dont keep watch on it. I did notice over the course of the day that the widgets/shortcuts on the desktop had seemed to stop working, but didnt take the time to restart it.
Got a new battery (another 35Euro!) and had them both charged just in case. Here's whats happening. Dunno if anybody can decipher it:
- when I switch it on with the battery, I get the NOKIA logo, backlight and steady blue status indicator, goes dead after 30secs
- Battery out, usb in: status indicator one flash orange. Thats it until I put the battery in again and I get a vibrate and NOKIA logo without backlight. After 30 secs it dies and repeats this cycle automatically
- if I switch it on with the battery in and plug it in while the backlight is on, it again vibrates and has dark logo, except now orange light stays steady every second cycle. If I take the battery out, the orange indicator stays on.
I dunno what firmware is on it, but I dont remember updating it in about two months. I wonder if flashing is a suitable thing for me to try or is my phone a gonner?!

It worked!!
Thanks to cpitchford's responses to other queries, this nube had some confidence to proceed
Almost feeling ballsy enough to try the leaked pr1.2 now but I reckon I just should copy my precious videos over for now!
Also gotta figure out how to get my contacts and sygic software back!
sweet

Yet another routing problem :/

I'm trying to setup something like this:
ADSL line
|
192.168.0.1 Netgear router
|
192.168.0.2 eth0 Arch box
192.168.1.1 eth1 /
|
192.168.1.2 Windows box
The rc.conf lines are:
MODULES=(dmfe 8139too uhci_hcd snd-via82xx snd-pcm-oss !usbserial !ide-scsi)
lo="lo 127.0.0.1"
eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth1="eth0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(lo eth0 eth1)
loopback="-host 127.0.0.1 lo"
gateway="default gw 192.168.0.1"
ROUTES=(gateway loopback)
After a network restart the ifconfig returns the following output:
eth0 Link encap:Ethernet HWaddr 00:80:AD:01:13:0D
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::280:adff:fe01:130d/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:24 errors:0 dropped:0 overruns:0 frame:0
TX packets:138 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3124 (3.0 Kb) TX bytes:3240 (3.1 Kb)
Interrupt:11 Base address:0xa400
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
What am I doing wrong here and how should I configure the arch box?
Thank you.

Oh boy... guess it's not a good idea to chill on a Sunday afternoon, having few beers and also tweaking Linux...
I have commited a typo which costed me about 1 hour of confusion.
Wrong setting:
eth1="eth0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255"
Good setting (after another beer):
eth1="eth1 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255"
:oops:
It's all smooth now.

Re: YAPP (Yet Another Printing Problem)

Ed,
I wonder if this is related to the printing feature I discovered
where things I print from Forte have a strong tendency to come out in
the same colours as my windows desktop, which is
typically yellow-on-black.
Sounds like your print windows are inheriting their color from the desktop. You can
change this in the window workshop on the color palette. The "i" in the palette
means the window inherits it color from the desktop.
Robert
MailTo:[email protected]
http://www.crisafulli-consulting.com
Crisafulli Consulting, Inc.
6 Founders Court Phone: (301) 972-9401
Damascus, MD 20872 FAX: (301) 972-9403

I can print OK with from my NT develpoment machine in colour, but when
running
the same app from the Win95 client with the printer attached locally the
coloured text disappears. Has anyone else come across this problem?Hi Jamie,
I wonder if this is related to the printing feature I discovered
where things I print from Forte have a strong tendency to come out in
the same colours as my windows desktop, which is
typically yellow-on-black.
- Ed
================================================================================
Eduard E Havelaar, Information Services Section, University of Canterbury
email: [email protected]
phone: +64-3-366 7001 extn 8910
fax: +64-3-364 2999
snailmail: Private Bag 4800, Christchurch, New Zealand

Yet another boot problem

Similar Messages

Maybe you are looking for