Yet another CD burning issue--won't finish "finishing"

The subject pretty much says it all. When I try burning a CD, the computer seems to go through the process just fine until the status becomes "Burning disc.....finishing," at which time, it stops. iTunes still works and is responsive, but the CD won't finish.
I've also tried burning discs with Windows Media Player, but it doesn't seem to work either.
Immediate responses would be greatly appreciated--I need to burn a disc as a gift ASAP!
Thanks in advance.
(Please note that at the time I ran the diagnostics, it still said it was "Burning disc.....finishing." Not sure if that's relevant or not, but figured it was worth noting anyway.)
Microsoft Windows XP Professional Service Pack 1 (Build 2600)
Emachines xxxxxxxxxxxxxx
iTunes 7.0.2.16
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.1
LowerFilters: PxHelp20 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.0.6.1),
Video Driver: Intel(r) 82810E Graphics Controller\Intel(R) 82810 Graphics Controller
IDE\DiskWDCWD800BB-00JHC0_____________________05.01C05, Bus Type ATA, Bus Address [0,0]
IDE\CdRomSAMSUNGCD-R/RW_SW-224B_________________R201___
Could not open CD handler, 5. Problem with installation of drive in Windows or drive contains copy protected CD.
Current user is an administrator.
D: SAMSUNG CD-R/RW SW-224B, Rev R201
Drive is empty.
The last failed audio CD burn had error code 4220(0x0000107c). It happened on drive D: SAMSUNG CD-R/RW SW-224B on CDR media at speed 12X.

hmmmmm.
i think i found your drivers and downloads page at Emachines:
Emachines T-series T1150
but there's not a lot of items of interest available there.
on the other hand, according to Samsung's support site, there's a newer version of the firmware available for your SAMSUNG CD-R/RW SW-224B. you've got R201, and they have R205 available for download:
Samsung SW-224B
so it might be prudent to contact your Emachines technical support, tell them you're troubleshooting a burning issue, and asking them if the newer R205 firmware is compatible with the particular Emachines system that you have.

Similar Messages

Yet Another P7N Diamond Issue

Apart from the ongoing problem I am still having in this thread I now have yet another dilemma. I bought a BFG 9800 GT OC2 as a upgrade and installed it the usual way ensuring I connected the 6 pin connector too and the pc does not boot up even after several attempts
Instead I am getting a strange beeping pattern one long beep then some shorts
Please if someone could shed some light I would greatly appreciate it even if its regarding my previous issue.

http://www.coolermaster.com/products/product.php?language=en&act=detail&tbcate=22&id=2543
I use the above Cooler Master PSU, zero issues. Has 4 pci-e connectors, so it's ready for quad sli if I ever want to go that route with my P6n Diamond. Has lots of different connection options, highly rated PSU. Not all Cooler Master PSUs underperform, just have to know what you're buying. The above supply also has 2 8 pin connectors so for instance when my GTX 295 arrives I'll have no trouble (card uses 6/8 pin). Reviews also can be helpful.

Yet another CC billing issue

I had to update the credit card on file with my Creative Cloud account. Since then, the card has not been billed. The last payment was made on October 6. The information on file is correct, and has been for quite some time (even with multiple attempts to re-update it). Now access to my Adobe products has been suspended. I tried calling Adobe multiple times ... once hanging up after 45 minutes of being on hold, another time choosing the call-back option and never receiving a call back, and finally getting the recording that the wait time was between 90 and 120 minutes. One time I got through on chat, but after the unsuccessful session I was told to call Customer Support. Yet a connection to sales was near instantaneous.
These wait times are completely unacceptable. I understand that the attack on your servers has caused big headaches, but hire some temporary support staff to get through this.
Please, Adobe, help me out. I need to use your products for work.
-Jon-

Hi Jon,
I am so sorry for the inconvenience faced by you, please provide me your contact number, if possible with an alternate contact number. I will follow up the issue.
I have send an email to you also, please respond.
Regards,
Rajshree

Yet Another Toshiba A75 Issue.. Can anyone solve it ???

I have a A75 Satellite. The issue I'm having is that everytime I try and install Windows XP, when it's copying files, it totally shuts down. It can stay running at the bios screen all day long, but when it comes to installing an OS, it shuts off.. Any fix for this ? Thanks !

Try cleaning the air vents. When it's at the BIOS screeen the CPU, memory, and hard drive aren't doing anything so very little heat is generated, but when the OS is being loaded, the CPU, memory, hard drive, and DVD drive are running and generating a lot of heat. If the vents are clogged with dust the fan won't be able to cool the unit down enough and the unit shuts down.

Yet another Quick TIme issue.

I made new audio in Digital Performer and imported an MOV file as the source video. The new file was saved as an MOV and plays perfectly on a mac. However, when I try to play this on my pc's QT, I have to load the new file first THEN the original file before both the video/audio play. Help!

OK, that makes total sense. Thank you very much Jon; that explains the issue very clearly. This of course begs another question though; how to I merge the new audio file and the original video file?
That may depend on how you plan to play the file. My preferred strategy is to create a new target file and prevent the original source files from being accidentally modified in case I need to repeat the merge sequence.
1) Open the source files.
2) Create a new empty player.
3) Copy the individual files to the empty player in the order you wish them played.
4 Save the resulting new file as a stand alone file.
This merged file would play in most versions of QT based apps but maight be a problem in some versions of mobile device players which require content be "flattened" to individual audio and video tracks. (I.e., the QT 7 player can play up to 99 mixed data tracks but some versions of the mobile players do not.)

Yet another MB sleep issue

Hi,
I read a lot of discussions and articles about MB sleep problems, but still not found solution or explanation of mine.
My book wakes from sleep immediately after lid is closed. The LED dims but lights up immediately (up to two seconds). This is part of kernel.log
Jan 13 22:05:46 kovomatix kernel[0]: hibernatewriteimage done(e00002eb)
Jan 13 22:05:46 kovomatix kernel[0]: sleep
Jan 13 22:05:48 kovomatix kernel[0]: Wake reason = EHC1
Jan 13 22:05:48 kovomatix kernel[0]: System Wake
Jan 13 22:05:48 kovomatix kernel[0]: Previous Sleep Cause: 5
Jan 13 22:05:48 kovomatix kernel[0]: The USB device HubDevice (Port 1 of Hub at 0xfd000000) may have caused a wake by issuing a remote wakeup (2)
What may be HubDevice here? I can't find 0xfd000000 in System Profiler (there is 0xfd100000 only).
Nothing is connected except power adapter. I'm using USB keyboard and Bluetooth mouse. Keyboard is unplugged, bluetooth is switched off. I tried to close all applications (only Finder was running in the Dock), switch od AirPort, Bluetooth, close all applications from top bar, but book still wakes up.
My Energy Saver settings should allow sleep (Computer Sleep: 3hrs, Display sleep 15min., do not wake for network access. Put hardisks to sleep and Automatically reduce brightness are unchecked.

Same issue :
5/3/11 10:48:15 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:15 ***s-mbp com.embraceware.awaken[9276] <Info>: Starting up
5/3/11 10:48:15 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:15 ***s-mbp com.embraceware.awaken[9276] <Debug>: Request started
5/3/11 10:48:15 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:15 ***s-mbp com.embraceware.awaken[9276] <Debug>: Command callback succeeded
5/3/11 10:48:15 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:15 ***s-mbp com.embraceware.awaken[9276] <Debug>: Request finished
5/3/11 10:48:15 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:15 ***s-mbp com.embraceware.awaken[9276] <Debug>: Request started
5/3/11 10:48:16 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:16 ***s-mbp com.embraceware.awaken[9276] <Debug>: Command callback succeeded
5/3/11 10:48:16 PM          com.embraceware.awaken[9276]          Tue May 3 22:48:16 ***ls-mbp com.embraceware.awaken[9276] <Debug>: Request finished
5/3/11 10:48:16 PM          AwakenHelper[509]          {
    SchedulePowerEventResult = "NO ERROR";
    "com.embraceware.awaken.error" = 0;
5/3/11 10:48:45 PM          kernel          PM notification timeout (pid 516, Safari)
5/3/11 10:48:45 PM          kernel          PM notification timeout (pid 516, Safari)
5/3/11 10:48:46 PM          kernel          AirPort: Link Down on en1. Reason 8 (Disassociated because station leaving).
5/3/11 10:48:46 PM          kernel          vmnet: bridge-en1: interface en is going DOWN
5/3/11 10:48:47 PM          kernel          vmmon: powerStateDidChange flags=0x4 (state 2)
5/3/11 10:48:47 PM          kernel          System Sleep
5/3/11 10:48:49 PM          kernel          Wake reason = EHC1
5/3/11 10:48:49 PM          kernel          System Wake
5/3/11 10:48:49 PM          kernel          vmmon: powerStateDidChange flags=0x82 (state 4)
5/3/11 10:48:49 PM          kernel          Previous Sleep Cause: 5
5/3/11 10:48:49 PM          kernel          The USB device HubDevice (Port 1 of Hub at 0xfd000000) may have caused a wake by issuing a remote wakeup (2)
5/3/11 10:48:51 PM          configd[14]          network configuration changed.
5/3/11 10:48:51 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Operation not supported on socket
5/3/11 10:48:51 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Invalid argument
5/3/11 10:48:51 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Device not configured
5/3/11 10:48:51 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Device not configured
5/3/11 10:48:52 PM          kernel          vmnet: VMNetDisconnect called for port 0x1309c400
5/3/11 10:48:52 PM          kernel          vmnet: bridge-en1: filter detached
5/3/11 10:48:52 PM          kernel          vmnet: bridge-en1: down
5/3/11 10:48:52 PM          kernel          vmnet: bridge-en1: detached
5/3/11 10:48:52 PM          kernel          vmnet: Freeing hub at 0x10ac8000.
5/3/11 10:48:53 PM          kernel          Auth result for: 00:1f:1f:66:06:08 MAC AUTH succeeded
5/3/11 10:48:53 PM          kernel          AirPort: Link Up on en1
5/3/11 10:48:53 PM          configd[14]          network configuration changed.
5/3/11 10:48:53 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Operation not supported on socket
5/3/11 10:48:53 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Invalid argument
5/3/11 10:48:53 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Device not configured
5/3/11 10:48:53 PM          de.novamedia.nmnetmgrd[30]          NMIfNet: Device not configured
5/3/11 10:48:54 PM          loginwindow[452]          in pam_sm_authenticate(): Failed to determine Kerberos principal name.
5/3/11 10:48:54 PM          kernel          vmnet: VNetUserIf_Create: created userIf at 0x13301f00.
5/3/11 10:48:54 PM          kernel          vmnet: VMNetConnect: returning port 0x13301f00
5/3/11 10:48:54 PM          kernel          vmnet: Hub 0 does not exist, allocating memory.
5/3/11 10:48:54 PM          kernel          vmnet: Allocated hub 0x1858d000 for hubNum 0.
5/3/11 10:48:54 PM          kernel          vmnet: VMNET_SO_BINDTOHUB: port: paddr 00:50:56:f9:0f:06
5/3/11 10:48:54 PM          kernel          vmnet: Hub 0
5/3/11 10:48:54 PM          kernel          vmnet:         Port 0
5/3/11 10:48:54 PM          kernel          vmnet: bridge-en1: got dev 0xdd90004
5/3/11 10:48:54 PM          kernel          vmnet: bridge-en1: wireless interface detected.
5/3/11 10:48:54 PM          kernel          vmnet: bridge-en1: up
5/3/11 10:48:54 PM          kernel          vmnet: bridge-en1: attached
5/3/11 10:48:54 PM          kernel          vmnet: VNetUserIfFree: freeing userIf at 0x13301f00.
5/3/11 10:48:55 PM          kernel          en1: DAD detected duplicate IPv6 address fe80:0005::cabc:c8ff:fee6:e320: NS in/out=1/1, NA in=0
5/3/11 10:48:55 PM          kernel          en1: DAD complete for fe80:0005::cabc:c8ff:fee6:e320 - duplicate found
5/3/11 10:48:55 PM          kernel          en1: manual intervention required
5/3/11 10:48:58 PM          Firewall[80]          krb5kdc is listening from :::88 proto=6
5/3/11 10:48:58 PM          Firewall[80]          krb5kdc is listening from 0.0.0.0:88 proto=6
5/3/11 10:50:00 PM          Apple80211 framework[470]          Scan() error 16 (Resource busy)
5/3/11 10:50:00 PM          Apple80211 framework[470]          __performScan() EBUSY, sleep 1 sec, try again
5/3/11 10:50:01 PM          Apple80211 framework[470]          Scan() error 16 (Resource busy)
5/3/11 10:50:01 PM          Apple80211 framework[470]          __performScan() EBUSY, sleep 1 sec, try again
5/3/11 10:50:16 PM          com.embraceware.awaken[9276]          Tue May 3 22:50:16 ***s-mbp com.embraceware.awaken[9276] <Info>: Shutting down

Yet another slow connection issue

My broadband speed is totally unreliable - and from a quick scan of the forums it seems I'm not the only one!
Much the same as numerous other posters, I'm paying for up to 8meg broadband but typically getting far less than that. Being in a rural location i appreciate that the local phone exchange probably isn't the most high tech facility in the world, but we're only 2 miles away from it and the speed tester has recorded up to 7meg on occasion. Today, and this seems to be an increasingly frequent occurence, the speed tester says "your IP profile is 250k".
We had an engineer out 3 weeks ago for the same problem but he could find no faults at the house, said there were no reported faults on the local exchange and the morning before he arrived the IP profile had already been reset to a more usable level. Rang the call centre again today and after wasting about an hour trying to explain the problem then waiting for him to check things and call me back, then explaining the same thing over again, absolutely nothing has been resolved and they want to send out another engineer.
I have a couple of very simple questions which the customer services team seem incapable of answering:
1. what is the reason for my IP profile being set so low?
2. what needs to be done to fix it now?
3. what needs to be done to stop it happening again?
I don't think the guy I spoke to actually knows what an IP profile is, let alone how to resolve a problem with it. What is the point of a technical support helpline when the staff quite obviously have no technical knowledge?!

Have spent another hour of my life on the phone to BT helpline this afternoon.
Apparently the reason we hadn't received the call back yesterday was due to a "technical issue" at their end and the request had not been passed on to the engineer team.
Having gone through exactly the same conversation and process as on Tuesday, the helpline chap has run his tests and when pressed told me that he could determine no faults on the line. An engineer might be able to determine other faults though so he would like to book an appointment for an engineer to call.
Unfortunately, even though I've waited 2 days for this already because they didn't pass on the engineer request the other day, they can't do anything to prioritise the call so I've now got to wait up to another 48hrs for somebody to ring me to book the appointment. As its Thursday now, that probably means that it could Monday before that happens and therefore probably the middle of next week before the engineer actually gets to the house. So another week of broadband that is barely faster than dial up.

Yet another External Harddrive issue

I use a Western Digital "My Passport" external hard-drive with my computer. It's been formatted to my Macbook, and that's the only computer it has been hooked up to. My problem is every single time I plug the hard-drive in my trash suddenly gains two files I deleted from it and they won't empty from said trash. Is there a virus issue or is there any way to fix this??

So what happens when you try to empty the trash with the hard drive connected?
What type(s) of files are these?
~Lyssa

Yet Another YouTube Connection Issue

Hi,
Long time Mac user, 1st time poster
Yes, I have the (apparently) infamous "I can't get the YouTube URL to work" problem. I have gone thru a number of the related/similar questions already on the ASC but still no joy.
For the past few months I cannot get my MacBook Pro to even see/load Youtube.com while at home using our iMac as a WiFi hub. It is not a video/Flash issue as I can load/view streaming video from many other sites. If I go on the road, Youtube loads & works fine. Our boy's Window's PC loads & runs Youtube fine from the same iMac at home. Wife has the same issue as me with her MacBook. It is only Youtube that will not load as an URL (as well as any imbedded YouTube videos).
The fact that two MacBooks have the identical problem running off the same WiFi connection (plus that the site works when using other hot spots) leads me to suspect its something on the iMac that is not allowing our MacBooks to load this site, but yet an old PC laptop using the same WiFi as us loads YouTube fine.
On the MacBook end I tried the HTML5, the direct IP, clearing all caches (including Library ones), reseting Safari, trying other browsers (Firefox has the identical problem), etc....and still can't see Youtube.com.
Could there be something on the iMac that is blocking this one site? The iMac is o-l-d & is simply used for WiFi.
Any help/suggestions would be appreciated!

Even the cheapest wireless router will work much better than what you have as a WiFi access point, and over the life of the device you'll probably save enough on electricity to recover the cost.

Yet another saved password issue ...

I use mozilla and the save passwords feature. On the tripadvisor.com site, I have a saved password. Yet, mozilla won't auto-fill the password.
Go to www.tripadvisor.com and try to sign in. If you don't have an account, don't worry, just click on sign-in and remember to turn on autocomplete on the form. Enter a username and password, when mozilla asks whether to save it or not, say yes.
OK. close your browser, clear cookies, all of that and go back to tripadvisor.com and click on sign-in.
The password won't be populated. Yet if you were to View Page Info -> Security, you'll see that passwords are stored. I can get the username and password from there and fill them in and that gets me logged in.
What I'd like to know is this. How can I get mozilla to populate the passwords automatically; they are stored, mozilla has them, just won't fill them in.

This looks like a JavaScript generated form.<br />
Firefox may save the name and password in such a case, but won't (autofill) the form in such a case.
There is currently work being done in the latest development version about this.
*Bug 355063 - Password manager does not work on script-generated forms
<i>Please DO NOT comment in bug reports: https://bugzilla.mozilla.org/page.cgi?id=etiquette.html</i>

Yet another tagged songs issue

Ok all, I have another question about tagged songs. I figured out how to buy a tagged song. On a windows machine, you have to hit the applications key and then there is a buy option. I bought two songs this way, but when I connected my IPod the other day to purchase a song I had tagged since I bought the last song, the buy option is no longer available. How do I buy the songs now?

http://www.coolermaster.com/products/product.php?language=en&act=detail&tbcate=22&id=2543
I use the above Cooler Master PSU, zero issues. Has 4 pci-e connectors, so it's ready for quad sli if I ever want to go that route with my P6n Diamond. Has lots of different connection options, highly rated PSU. Not all Cooler Master PSUs underperform, just have to know what you're buying. The above supply also has 2 8 pin connectors so for instance when my GTX 295 arrives I'll have no trouble (card uses 6/8 pin). Reviews also can be helpful.

Yet another CD burn error (4280)

It seems that the 4280 problem is fairly common. In my case, ever since Itunes was updated, I've had problems with trying to burn CDs. It would always stop and then say "unknown error-4280". I tried solutions that others have used, but it doesn't seem to work. I can rip CDs just fine, I just can't seem to burn any anymore and before Itunes was upgraded, I was able to burn CDs just fine.
Here are my diagnostics:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Dell Computer Corporation Dimension 2400
iTunes 7.1.1.5
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.2
LowerFilters: PxHelp20 (2.0.0.0), Cdr4_xp (8.0.0.212),
UpperFilters: GEARAspiWDM (2.0.6.1), Cdralw2k (8.0.0.212), pwd_2k (6.1.0.91),
Current user is an administrator.
Video Display Information:
Intel(R) 82845G/GL/GE/PE/GV Graphics Controller
Connected Device Information:
DiskDrive, WDC WD400EB-75CPF0, Bus Type ATA, Bus Address [0,0]
CDROM, OPTORITE CD-RW CW5205, Bus Type ATA, Bus Address [1,0]
CDROM, SAMSUNG CD-ROM SC-148A, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
D: SAMSUNG CD-ROM SC-148A, Rev B402
Drive is empty.
E: OPTORITE CD-RW CW5205, Rev 180E
Drive is empty.
The last failed audio CD burn had error code 4280(0x000010b8). It happened on drive E: OPTORITE CD-RW CW5205 on CDRW media at speed 4X.
Dell Windows XP

I am using the latest Itunes and don't have an Ipod.

[SOLVED, sort of] Yet another UEFI boot issue

Hello everyone,
Let me start by saying sorry for the long (first) post.
I've ended up with a UEFI boot problem I can't solve. I've searched the forum and internet and I realize I'm not the only one who ran into problems with UEFI. Unfortunately, the problems other have had seem not similar to mine. I've spent almost 2 days now trying to figure this out, and I'm getting nowhere (though I've learnt some more about UEFI, which I guess is good). I was hoping someone here can give me some hints on how to proceed.
So lets start with the background. I recently bought a new computer (Lenovo Thinkpad Edge E530 with Windows 8) and of course I want to run ArchLinux on it (been using ArchLinux for almost 7 years now and no plans on switching). Installation went ok with only a few problems during installation that I managed to solve (or so I thought). I must admit I didn't follow the guide fully. I didn't want to remove the Restore and Windows partitions, so I figured it would be safe to reuse the existing UEFI System Partition, as long as there was enough room, which there was. Anyway, I now have a computer I can boot into ArchLinux and also Windows 8, just the way I want it, almost. There is this one final issue I haven't been able to figure out how to solve.
The problem
Whenever I reset/power on the computer, I must press Enter during the initial screen (showing a Lenovo logo, and a message about pressing Enter to interrupt normal startup). If I don't press Enter before the timeout (a second or so), the screen will go white and that's it. No beep, no message, no nothing but a white screen. A power cycle is the only way to leave this state. Occasionally the screen will be a white bar at the top and random colours below, but I'm guessing this only represents what is in graphics memory at the time (0x00, 0xFF or any other random value).
If i do press Enter however, then I'm presented with a menu where I can select what to boot; rEFInd (which is preselected) along with Windows 8 and some restore and diagnostic entries. Pressing enter will take me to the preselected rEFInd, pressing enter again (or wait for timeout) will boot linux, and I'm in. Nothing weird there. And if I select Windows in rEFInd, then windows boot, just as expected.
There is no difference whether I'm switching from Windows to Linux or Linux to Windows or just reboot the same OS I was using again. The result is the same whatever I choose to boot.
So the question is: Why do I have to select rEFInd manually and go through all these menus? Should I not be able to just power it on and let it boot the preselected rEFInd entry and continue from there, without me helping it?
Trying to solve it
Searching here and on the internet gave me some ideas on what to try, so here is a list of my attempts:
efibootmgr show me there is a rEFInd entry, and that it is the first one in boot order
I copied refindx64.efi to /boot/efi/EFI/Boot/bootx64.efi (replacing an existing entry)
I've updated the EFI firmware (from Lenovo) to the latest and greatest
One other guy had almost the same issue, but with a single boot of Windows. He solved it with Microsoft Boot Manager (there is an Automatic Repair, or something). I even dared trying this, though I must admit I was a bit hesitant about letting some Microsoft program trying to repair my computer. Anyway, it said it couldn't repair my problem, nor did it say I had one, so I am none the wiser.
None of the above gave anything.
So, that's it. I guess I can live with having to press Enter on every power up/reset, but it is very annoying having to do so, and even more so when I forget it because then I'm forced to power cycle it. I hope someone reading this can figure out what's going on, because I am clueless.
Best regards,
Johan
Last edited by 6feet5 (2013-01-08 19:03:50)

WonderWoofy wrote:@srs5694, have you thought about filing a bug report/feature request about the naming scheme here? I would imagine that something coming directly from the upstream developer would be something that they should take into consideration. Also, I imagine that renaming it to refindx64.efi kind of goes against the whole "vanilla packages" thing we tout around here... so it really makes me wonder why it is done in the first place.
I've just done that:
https://bugs.archlinux.org/task/33326
It's not been very important until recently; but I've been putting a lot of effort into the ancillary support scripts (install.sh and mvrefind.sh). They necessarily rely on the files having certain names, so installing them under other names robs users of functionality.
6feet5 wrote:I've decided to try and restore the whole unit, thinking it would take maybe an hour or two. It's been running now for almost 3 hours and only completed 20%.
Good luck with that!
FWIW, it seems that the number of EFI-related bug reports on Linux forums has gone way up recently. No doubt this is because EFI is now pretty much universal on new computers, so problems that used to affect one or two people now affect dozens or hundreds, and some of those post about them.

[SOLVED] YASBI (yet another screen brightness issue)

i feel silly posting this, as there seems to be a lot of documentation about this, but i'm kind of baffled. if i run
echo "5" > /sys/class/backlight/acpi_video0/brightness
as root, everything works nicely, my screen turns it's brightness down to half-way (max brightness is 10).
if i run the same command as sudo, i get a permissions error. my final goal is to bind this to a key in openbox, but first i need to figure out what i'm doing wrong. do i need to be part of a certain group? do i need to edit my sudoers file?
thanks in advance.
Last edited by williamkray (2012-02-02 22:49:56)

i have solved this, and am posting how here for anyone else who might come across this in a search. this is what i came up with:
added the following to my /etc/rc.local:
chgrp users /sys/class/backlight/acpi_video0/brightness && chmod g=+rw /sys/class/backlight/acpi_video0/brightness
then i came across this script on another forum post, and saved it to /usr/sbin/brightness, made it executable and chgrp users:
#!/bin/bash
file="/sys/class/backlight/acpi_video0/brightness"
level=$(cat $file)
if [[ "$#" -eq 0 ]]; then
cat $file
elif [[ "$1" = "-" ]]; then
echo $(( level - 1 )) > $file
elif [[ "$1" = "+" ]]; then
echo $(( level + 1 )) > $file
fi
then in my ~/.config/openbox/rc.xml i added the following code to bind the commands to my Super+Up and Super+Down :
<keybind key="W-Up">
<action name="Execute">
<command>brightness +</command>
</action>
</keybind>
<keybind key="W-Down">
<action name="Execute">
<command>brightness -</command>
</action>
</keybind>
Last edited by williamkray (2012-02-02 22:51:28)

[Solved]Yet Another HAL / Mounting issue....

My issue can be avoided by manually mounting a device, just to get that out there.
Whenever I transfer a larger file ( > 200mb) onto a removable USB device formated in either FAT or any non-journaled filesystem, Thunar will *pretend* like its unmounting the device but after about 20 seconds it states:
Failed to unmount "<device name>".
Did not receive a reply. Possible causes include: the remote application did not send a reply,
the message bus security policy blocked the reply, the reply timeout expired,
or the network connection was broken.
On top of the message, my data written is mostly corrupt.
What I know:
** Thunar uses exo-unmount to unmount devices given a HAL uuid. Maybe this is failing? Any clue how to debug this?
** 20-storage-methods.fdi states that all vfat mounted devices have 'flush' and 'async' mount options... could this be an issue?
** I'm part of the 'storage' and 'power' groups.
** i start XFCE using ck-launch-session startxfce4
I've made sure that the device has no other handles and is not open in any window. My system(s) all have new and updated HAL and DBUS, as well as every other package. Running 'sync' after writing the files sometimes fixes the issue. Does anyone have a fix for why removable drives aren't "sending a reply" ? Thanks!
--Anthony
Last edited by anthonyclark (2010-09-22 17:48:13)

Alright ... well. I managed to solve this kind of. As per my last post regarding the same exact issue, I must've missed a reply from Inxsible telling me to use the FIRST suggest UDEV rule from the arch udev wiki.
The result of this is basically...
*Device inserted
*Mounted in /media/<device name> automatically
*(No access via Thunar sidepane since it gets mounted with `mount`)
*No need to manually unmount
*just unplug or power off the device and it gets "lazy" unmounted via `unmount`
Downside:
*Mounting a drive via TrueCrypt creates a directory in /media that doesn't get automatically deleted.
*Not a solution to Thunar having response issues with unmounting.
/etc/udev/rules.d/11-media-by-label-auto-mount.rules
KERNEL!="sd[a-z][0-9]", GOTO="media_by_label_auto_mount_end"
# Import FS infos
IMPORT{program}="/sbin/blkid -o udev -p %N"
# Get a label if present, otherwise specify one
ENV{ID_FS_LABEL}!="", ENV{dir_name}="%E{ID_FS_LABEL}"
ENV{ID_FS_LABEL}=="", ENV{dir_name}="usbhd-%k"
# Global mount options
ACTION=="add", ENV{mount_options}="relatime"
# Filesystem-specific mount options
ACTION=="add", ENV{ID_FS_TYPE}=="vfat|ntfs", ENV{mount_options}="$env{mount_options},utf8,gid=100,umask=002"
# Mount the device
ACTION=="add", RUN+="/bin/mkdir -p /media/%E{dir_name}", RUN+="/bin/mount -o $env{mount_options} /dev/%k /media/%E{dir_name}"
# Clean up after removal
ACTION=="remove", ENV{dir_name}!="", RUN+="/bin/umount -l /media/%E{dir_name}", RUN+="/bin/rmdir /media/%E{dir_name}"
# Exit
LABEL="media_by_label_auto_mount_end"
Last edited by anthonyclark (2010-09-22 03:50:00)

Yet another CD burning issue--won't finish "finishing"

Similar Messages

Maybe you are looking for