Yet another internet problem after updating to Leopard

After 3 attempts, I've finally got Leopard installed on my Macbook Pro (just over 18 months old, was running Tiger perfectly well) and i STILL can't get internet access.
The Airport says its connected but nothing loads at all - it won't send/receive messages, it won't load webpages, it just sits there doing nothing until eventually (often after half an hour or more) it'll tell me that the connection has timed out.
I've done the following changes as suggested elsewhere on the internet -
1. Changed IPv4 settings to manual and doublechecked these are correct - they weren't the first time round, it was inventing phantom numbers and confusing my router for the actual interwebs. So changed that.
2. Turned IPv6 to Off on both airport and ethernet
3. corrected DNS entries for the Airport - again left to its own devices it thinks the router's IP address is the DNS address. So I added the correct 2 plus the two from Open DNS for good measure. I've tried different combinations of all 4, only the router two, only the open DNS 2 and so on and so forth and it still won't work!
4. tried restarting several times after each change.
5. double checked i don't have any of the .plist files from Tiger that might be interfering.
6. checked for a trojan horse
7. checked my router is working (it is).
And, nothing worked. It's still rubbish and does nothing. I wish I had never spent the money on the stupid upgrade and am never going to do it again!
Can anyone help?!
I've got 10.5.4 and then I patched it with the 10.5.5 Combo update too. I went for an Erase and Install option too. I'm not the most mac savvy person around, so please be gentle!
TIA.

I've checked, double checked, triple checked, tested, quadruple checked... My router is working perfectly, it works with my blackberry, friends laptops, my PC... just not my Mac. All the addresses are correct - left to its own devices the laptop with Leopard on it will NOT use the correct info for the DHCP or any other address. It uses incorrect information, confusing the Router itself with the actual internet (basically all the address fields that are meant to point you at, like, "the internet" will instead just point you to the router and the router of course replies with Hey man, whaddya want? I'm just a router... so nothing happens). Changing that gave me some internet access where previously it wasn't getting any. But all webpages take forever to load - often not loading at all - and after about 10 minutes of occasionally working the whole thing will pack up.
I flat out refuse to fork out £300 for a new router just because Apple decided to make their new OS incompatible with anything but Time Capsule (as I suspect is probably the case given loads of people are having the same problems and there's been a noticeable silence on the subject from Apple). So I guess I'll be wiping the macbook AGAIN and reinstalling Tiger from the recovery disc.
Next computer - back to a windows PC! I'm sure Microsoft are loving Leopard.

Similar Messages

Software Installer and wireless internet problems after upgrade from Leopard to Lion.

Last weekend I upgraded the OS on my MacBook Pro from Leopard to Snow Leopard, and then from Snow Leopard to Lion. I'm having a couple of problems.
First, I cannot get the wireless internet to work. My internet connection is fine, I can plug the ethernet cord in and all is well. But I cannot get wireless signals to work. Have tried both my Airport Express and an old linksys router, and neither seem to work. They both worked just fine before the update. I had very fast wireless internet, and now nothing. With the Airport Express, when I plug it in iti'll just continuously blink orange, and the Airport Utility refuses to recognize it. The linksys router seems to work, because it puts off a signal and my iPhone connects to it. My computer recognizes the signal, but it won't open any internet pages, says I'm not connected.
Today I tried to install Apple's Migration Assistant software to help with my first problem. But a funny thing happened. The software installer says I don't have enough space. But I have plenty- I have almost 200 GB, and I only need 5 MB for the program. I've never seen this happen before, it's so odd. Any suggestions?
I really appreciate any assistance/suggestions!
Thanks,
Ellen

EDLIU wrote:
How do I purchase "Snow Leopard" from Mac App Store?
Please give me the link to "purchase and download the Snow Leopard" in Apple Online Store.]
You can't purchase Snow Leopard from the Mac App Store. Or "download" it. That will be possible for Lion.
For the Apple Online store, why can't you just look for yourself?
http://store.apple.com

I have a internet problem- after updating to v.40 ...

hello guys,
yesterday i update my phone to version 40, and i have a critical problem..
when i open an application or "opera mini" for example, it doesnt ask for internet connections (WIFI, WAP, 3G INTERNET). in version 30,31 it was automatic ask me. i dont know what to do, cause all the applications with internet doesnt work for me,
*when i have a WIFI connection in the erea, its automatic connecting to this one.
whats weird? with the original explorer on the phone- it works! all is fine, no problems.
i didnt change any settings at all, i tried to reinstall things same in C device and i have this problem too, so i dont thing its a problem of the memory card.
i need help, its importent for me..
sorry for the poor english.
good day !

Goto-- Settings-- Connectivity-- Destinations--- remove default & set default as Always Ask option..
-Sam
Hit Kudos to show your appreciation.

Yet another bootcamp problem after yosesmite

Hello all,
i'm one of the lucky people who have broken the win partition (win 8.1) with the update to last osx update. (the partition is/was of 50gb)
here are my output (i read some threads but i don't get what i can do after those two commands).
stefano@~$ diskutil list
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *251.0 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:          Apple_CoreStorage                         200.0 GB   disk0s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
   4:       Microsoft Basic Data                         20.0 GB    disk0s4
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                  Apple_HFS Macintosh HD           *199.6 GB   disk1
                                 Logical Volume on disk0s2
                                 E1AB8035-EA99-4BE4-AFF7-B634DDA4F904
                                 Unencrypted
stefano@~$ diskutil cs list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group C9468AA2-59FF-4469-A02B-2D0EE8764B38
    =========================================================
    Name:         Macintosh HD
    Status:       Online
    Size:         200000000000 B (200.0 GB)
    Free Space:   18993152 B (19.0 MB)
    |
    +-< Physical Volume E33CC934-6863-442C-99DA-5E3FEC5C1A3C
    |   ----------------------------------------------------
    |   Index:    0
    |   Disk:     disk0s2
    |   Status:   Online
    |   Size:     200000000000 B (200.0 GB)
    |
    +-> Logical Volume Family 4968BB0C-61CE-4F2C-94EA-D3164F4E87DB
        Encryption Status:       Unlocked
        Encryption Type:         None
        Conversion Status:       NoConversion
        Conversion Direction:    -none-
        Has Encrypted Extents:   No
        Fully Secure:            No
        Passphrase Required:     No
        |
        +-> Logical Volume E1AB8035-EA99-4BE4-AFF7-B634DDA4F904
            Disk:                  disk1
            Status:                Online
            Size (Total):          199628685312 B (199.6 GB)
            Conversion Progress:   -none-
            Revertible:            Yes (no decryption required)
            LV Name:               Macintosh HD
            Volume Name:           Macintosh HD
            Content Hint:          Apple_HFS
tefano@~$ sudo gpt -vv -r show /dev/disk0
Password:
gpt show: /dev/disk0: mediasize=251000193024; sectorsize=512; blocks=490234752
gpt show: /dev/disk0: Suspicious MBR at sector 0
gpt show: /dev/disk0: Pri GPT at sector 1
gpt show: /dev/disk0: Sec GPT at sector 490234751
      start       size index contents
          0          1         MBR
          1          1         Pri GPT header
          2         32         Pri GPT table
         34          6
         40     409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
     409640 390625000      2 GPT part - 53746F72-6167-11AA-AA11-00306543ECAC
391034640    1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
392304176   58868176
451172352   39061504      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
490233856        863
490234719         32         Sec GPT table
490234751          1         Sec GPT header
stefano@~$ sudo dd if=/dev/rdisk0s4 count=1 2>/dev/null |hexdump -C
00000000 aa 05 2e 06 26 05 1b 06 84 06 27 07 c4 06 93 06 |....&.....'.....|
00000010 3c 06 d4 05 f1 05 a7 05 6c 05 82 05 d7 05 92 05 |<.......l.......|
00000020 18 06 dd 05 d8 04 87 04 75 05 07 06 fb 05 42 06 |........u.....B.|
00000030 48 06 6d 06 6d 06 6f 06 26 06 cc 05 70 05 fa 07 |H.m.m.o.&...p...|
00000040 a9 08 ce 08 f3 08 ad 08 be 08 77 09 2a 09 7e 08 |..........w.*.~.|
00000050 f5 08 2c 09 ed 08 e7 09 27 09 f3 08 93 09 90 09 |..,.....'.......|
00000060 fe 08 23 09 bc 09 22 09 e6 08 0a 0a e9 09 a2 09 |..#...".........|
00000070 4b 09 50 09 0c 0a 96 09 31 09 b1 09 79 09 21 0a |K.P.....1...y.!.|
00000080 e0 09 41 0a e5 0a 83 09 ad 09 87 09 dd 0a f7 09 |..A.............|
00000090 6f 09 03 0b aa 09 37 0a 3d 0a b6 0a f5 09 bc 0a |o.....7.=.......|
000000a0 33 0a 7d 0b 2c 0c 45 0b b5 0a 57 0a 05 0b 56 0c |3.}.,.E...W...V.|
000000b0 d9 0a 20 0c 17 0b 9f 0b 4f 0b 5e 0b dd 0a d1 0a |.. .....O.^.....|
000000c0 2e 0a 68 0b cf 0a 6e 0c 62 0d 8b 0b 86 0b 4d 0c |..h...n.b.....M.|
000000d0 69 0c 3e 0d 3b 0c a0 0c ae 0b 69 0c 3f 0c 00 00 |i.>.;.....i.?...|
000000e0 00 00 7c 1a 85 1b be 17 ba 18 83 16 1f 18 74 14 |..|...........t.|
000000f0 f3 16 02 14 40 12 15 0b 00 0e c5 10 78 14 c8 13 |[email protected]...|
00000100 3b 13 7a 12 f5 12 45 14 da 14 4e 11 20 13 63 11 |;.z...E...N. .c.|
00000110 2d 12 d8 11 49 11 b2 11 f0 10 79 11 c0 0f 49 11 |-...I.....y...I.|
00000120 55 0f 35 10 16 0f 46 10 d9 0e d9 0e cc 0e 27 0f |U.5...F.......'.|
00000130 d9 0e 08 0e c6 0e d2 0c a8 0d 77 0d 89 0d 2c 0d |..........w...,.|
00000140 2a 0c 08 0d 15 0c 54 0c cc 0c ec 0b f4 0b db 0c |*.....T.........|
00000150 1a 0c 50 0b 58 0c 4f 0b f5 0b 39 0c 3f 0b 63 0b |..P.X.O...9.?.c.|
00000160 71 0b 66 0b 78 0b da 0a 38 0a 74 0a bc 0a 35 0a |q.f.x...8.t...5.|
00000170 61 0a a7 0a 81 0a d0 09 9b 0a 0d 0a 68 0a ad 09 |a...........h...|
00000180 f4 09 b2 09 13 0a 76 09 7c 09 1c 09 61 09 4d 09 |......v.|...a.M.|
00000190 4d 09 11 09 ed 08 59 09 08 09 82 08 4c 08 72 08 |M.....Y.....L.r.|
000001a0 5b 08 88 06 65 05 7e 05 4d 06 81 05 d7 05 9f 05 |[...e.~.M.......|
000001b0 cc 05 20 05 f2 04 c8 04 3a 05 16 05 65 05 26 05 |.. .....:...e.&.|
000001c0 09 05 0e 05 53 05 71 05 62 05 7d 07 b6 07 8c 07 |....S.q.b.}.....|
000001d0 39 07 69 07 07 07 6c 07 56 07 86 07 90 07 79 06 |9.i...l.V.....y.|
000001e0 1d 06 f5 04 db 04 84 04 25 04 81 04 22 04 1c 04 |........%..."...|
000001f0 21 04 2d 04 ee 03 ee 03 1f 04 e0 03 b8 03 b8 03 |!.-.............|
00000200
what can i do? i can't format windows, i mean, i've some data there that are just there and i don't have a backup.
adding details

now:
stefano@~$ sudo dd if=/dev/rdisk0s4 count=1 2>/dev/null |hexdump -C
00000000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000200
but
tefano@~$ sudo gpt -vv -r show /dev/disk0
gpt show: /dev/disk0: mediasize=251000193024; sectorsize=512; blocks=490234752
gpt show: /dev/disk0: Suspicious MBR at sector 0
gpt show: /dev/disk0: Pri GPT at sector 1
gpt show: /dev/disk0: Sec GPT at sector 490234751
      start       size index contents
          0          1         MBR
          1          1         Pri GPT header
          2         32         Pri GPT table
         34          6
         40     409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
     409640 390625000      2 GPT part - 53746F72-6167-11AA-AA11-00306543ECAC
391034640    1269536      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
392304176   97930543      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
490234719         32         Sec GPT table
490234751          1         Sec GPT header
stefano@~$ sudo gdisk /dev/disk0
GPT fdisk (gdisk) version 0.8.10
Warning: Devices opened with shared lock will not have their
partition table automatically reloaded!
Partition table scan:
MBR: hybrid
BSD: not present
APM: not present
GPT: present
Found valid GPT with hybrid MBR; using GPT.
Command (? sudo fdisk /dev/disk0
Disk: /dev/disk0 geometry: 30515/255/63 [490234752 sectors]
Signature: 0xAA55
         Starting       Ending
#: id cyl hd sec - cyl hd sec [     start -       size]
1: EE    0   0   2 -   25 127 14 [         1 -     409639] <Unknown ID>
2: AC 1023 254 63 - 1023 254 63 [    409640 - 390625000] <Unknown ID>
3: AB 1023 254 63 - 1023 254 63 [ 391034640 -    1269536] Darwin Boot
4: 00    0   0   0 -    0   0   0 [         0 -          0] unused
stefano@~$ diskutil list
/dev/disk0
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:      GUID_partition_scheme                        *251.0 GB   disk0
   1:                        EFI EFI                     209.7 MB   disk0s1
   2:          Apple_CoreStorage                         200.0 GB   disk0s2
   3:                 Apple_Boot Recovery HD             650.0 MB   disk0s3
   4:       Microsoft Basic Data                         50.1 GB    disk0s4
/dev/disk1
   #:                       TYPE NAME                    SIZE       IDENTIFIER
   0:                  Apple_HFS Macintosh HD           *199.6 GB   disk1
                                 Logical Volume on disk0s2
                                 E1AB8035-EA99-4BE4-AFF7-B634DDA4F904
                                 Unencrypted

Apple cinema Display problem after update

I had a similar problem to lain Maclreud
Immediately after updating to 10.4.11 and rebooting the toparea on my cinema display went dim and I saw the 2 short, one lon blinks on my power display LED
I didn't try it on another computer yet or try to change my power source but I may need a new backlight card as well. Please post if you have had similar problems after updating and suggest possible solutions.

Have you tried the Command-Option-P-R keys to reset the PRAM? (Maybe the upgrade has messed up the display settings?)
http://docs.info.apple.com/article.html?artnum=2238

White screen problem after updating to 1.1 firmware

My 2G iPod Nano worked fine with 1.0.1 and 1.0.2 firmware but after updating to 1.1 I get white screen everytime I turn it on after longer period of time. Turning the iPod off and then right back on makes it work again. I have done restore 3 times without effect. I even removed the firmware files so that iTunes downloads them again when doing the restore but that didn't work either.
Should I return it or wait for new firmware? Has anyone else had this problem after updating to 1.1?

Disconnect iPod and close iTunes.
Firmware files are in "Documents and Settings\username\Application Data\Apple Computer\iTunes\iPod Software Updates" folder.
You should still have the 1.0.2 files named "iPod_19.1.0.2.ipsw" and "iPod_19.1.0.2.ipsw.signature" in there if have you upgraded from 1.0.1 version.
Remove 1.1 files from the folder so that only those to files are in there.
Disconnect from network (I switched off my wlan) so that iTunes can't download the new version. Connect your iPod and do Restore, iTunes will now use the old firmware files because it can't connect to the internet.
Fujitsu Siemens Amilo M3438G Windows XP

Photoshop CS2 problems after updating to 10.4.5.?

Anybody notice Photoshop CS problems after updating to 10.4.5.?

Hello I had the same problem
I found the following information that helped me.....
Program errors occur when software conflicts arise due to an updated operating system. You can resolve these errors when you also update the driver software that causes the conflict or when you update the operating system. Program errors can also occur because of a damaged Photoshop preference file, or if there is a problem with a phone or internet connection. The Apple Disk Utility fixes file system errors that can also cause program errors.
Error "Could not complete your request..." or "Could not create a new document..." (Photoshop CS2 on Mac OS X v10.4)
Issue
Adobe Photoshop CS2 returns one of the following error messages:
"Could not complete your request because of a program error" when you try to open a file.
"Could not create a new document because of a program error" when you try to create a new file.
Solution 1:
Install the most recent update to Mac OS.
Solution 2:
Re-create your preferences files.
1. Hold CommandOptionShift when you start Photoshop.
2. Click Yes to the message, "Delete the Adobe Photoshop Settings file?"
Solution 3:
Disconnect your Internet connection.
To disconnect your Internet connection, do one of the following:
If you are connected to the Internet via a telephone modem, then disconnect from the modem.
If you are connected to the Internet via cable modem or DSL, then disconnect the ethernet cable from your computer.
Solution 4:
Use a disk repair utility.
Restart your Mac in Single User mode and run fsck -fy . For more information about the fsck command, please visit the Apple website at http:/docs.info.apple.comarticle.html?artnum=106214 .
Solution 5:
Ensure that all your drivers are compatible with Mac OS X v10.4.
Determine if your printer and video card (and any other peripherals you might have) are compatible with Mac OS X v10.4, and visit the manufacturers' websites to update the drivers.
Solution 6:
Re-create your printers in Mac OS X.
To re-create your printers, first delete them and then add them again.
To delete your printers:
1. Open System Preferences from the Apple menu.
2. Select Print & Fax, and click Printing.
3. Select each printer in the list and click the delete key (the minus key).
For instructions on how to add your printers again, see "Setting up to print to a printer" in Mac Help or search Help using the phrase "add a printer."
The one that fixed it for me was solution 6 -- re-creating my printers
I don't know why but it could be worth a try
Good luck
ADAM
17" Powerbook G3 iMac Mac OS X (10.4.3)
17" Powerbook G3 iMac Mac OS X (10.4.3)
17" Powerbook + G3 iMac Mac OS X (10.4.5)

Problems after updating from Mavericks to Yosemite.

Hello everyone.I have noticed some battery problems after updating from Mavericks to Yosemite like no charging at all (but the orange led was on )and not able to fully charged.I solve them with SMC reset and PRAM reset.Furthermore, battery discharges faster than before and its really annoying.Now I have notice that the upper right corner of my mac is getting hot.I'll appreciate any help
MacBook Pro (Retina, 13-inch, Late 2013

Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
    b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
4. Reinstall Yosemite: Reboot from the Recovery HD. Select Reinstall OS X from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.
5. Reinstall Yosemite from Scratch:
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
Note: You will need an active Internet connection. I suggest using Ethernet if possible
            because it is three times faster than wireless.

Unlock problem after update to iOS 7.1.1

I'm wondering is anyone of you encounter above mentioned problem after update to iOS 7.1.1.
Usually will switch off the phone during sleeping time, today woke up urn it on and wanted to check mail, the screen is freeze when enter the passcode.
Even try calling in with another phone also unable to get through. Passcode unable to key and stop at the 'enter passcode' screen.
After awhile it show the "apple" icon and turn off.
Any solutons to solve it?

iPhone is unresponsive and displays the Apple Logo
Review this article: iOS: Unable to update or restore.

Problem in update snow leopard 10.6. 2 to version 10.6.4 on Imac 27 "I7

Problem in update snow leopard 10.6. 2 to version 10.6.4 on Imac
27 "I7
When do the automatic update of version 10.6.2. to version
10.6.4 when it comes to "Apple" and the hourglass to "think" that moment appears on the screen too fast some risks.
Does anyone know how to solve this? I happen to other customers?

Hi slbruilima
The best way to bring the system up to date from 10.6.2 is to download and install the 10.6.4 Combo Update from the following link. > http://support.apple.com/kb/DL1048
Dennis

My itunes opens after 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to 12.x ....my operating system win7;processor i5 intel haswell and 4gb ram...i hav no issue

My itunes opens 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to the latest 12.0.1....my operating system windows7;processor i5 intel haswell and 4gb ram...i have no issue with opening other big programs....i tried uninstalling completely the itunes and reinstalling it as i thought at first it is not opening (because it takes really long time) and i followed the following support pages
1)iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
2)iTunes for Windows doesn't open after upgrading in Windows Vista, Windows 7, or Windows 8
but my problem doesnot get solved even after trying all the methods in the above pages...
now i realized,it opens after 2-3 hrs and at will...after opening it keeps hanging.finally it doesnot again open immediately after closing...kindly help me out as soon as possible

My itunes opens 2-3 hrs after doubleclicking it to open;it happened once or twice with itunes 11.x , but its a constant problem after updating itunes to the latest 12.0.1....my operating system windows7;processor i5 intel haswell and 4gb ram...i have no issue with opening other big programs....i tried uninstalling completely the itunes and reinstalling it as i thought at first it is not opening (because it takes really long time) and i followed the following support pages
1)iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
2)iTunes for Windows doesn't open after upgrading in Windows Vista, Windows 7, or Windows 8
but my problem doesnot get solved even after trying all the methods in the above pages...
now i realized,it opens after 2-3 hrs and at will...after opening it keeps hanging.finally it doesnot again open immediately after closing...kindly help me out as soon as possible

Iphone 5 back camera problem after update to IOS 8. Focus doesn't work on back camera!

My device is Iphone 5 64gb IOS 8.
I have problem after update to IOS 8. When i run camera.. I hear some scratch inside my phone. And focus of back camera doesn't work.
1. How can i fix it?
2. Or how to rollback to IOS 7+ ?
3. Should i come to app store with this problem?

I'm having this same problem too. Worked fine prior to iOS update. I contacted Verizon this morning who advised that this is a known issue. They suggested I backup my device, and perform a factory data reset. When prompted to update to iOS 8 again, re-installation has been known to resolve the issue. With all the problems with iOS 8, camera, and overall device slowing, I might just wait for a follow on SW turn.

What cause searching network problem after updating iphone 6 from iOS 8.1.2 TO iOS 8.1.3?

what cause searching network problem after updating iphone 6 from iOS 8.1.2 TO iOS 8.1.3?

SSince Apple does not support downgrading the iOS I suggest you start a new question that gives a good title to a specific problem. Then in the body of the thread describe the problem in detail, tell us what steps you have tried so far to correct the problem, what happened, and what error messages you received.

HT4623 I AM FACING PROBLEM AFTER UPDATING (7.0.4) MY PHONE MODEL 5C,AFTER THIS UPDATE SOME TIMES I CANT MAKE CALLS & SOME TIMES WHEN ANY BODY ELSE WANTS TO CALL ME BACK THE MESSAGE COME THAT THE USER IS NOT REACHABLE.PLS HELP

I AM FACING PROBLEM AFTER UPDATING (7.0.4) MY PHONE MODEL 5C,AFTER THIS UPDATE SOME TIMES I CANT MAKE CALLS & SOME TIMES WHEN ANY BODY ELSE WANTS TO CALL ME BACK THE MESSAGE COME THAT THE USER IS NOT REACHABLE.PLS HELP

I am facing the same issue! I bought 5c few days back
and everything was fine till I updated the software 7.0.4!
Whenever am connected to wifi am unable to make a call and if someone tries
Calling me they get the message that my number is not
Reachable! When I go back to 3G the calls work perfectly!!
Please help me out since I use wifi more than my network.
Appreciate any advise on this

Flash player problem after updating to belle on my...

flash player problem after updating to belle on my nokia c7.when I try to play .flv videos screen goes blank as show in image,previously these videos runs fine on symbian anna plz help plz help or tell me the way to downgrade to anna
Attachments:
scr000002.jpg ‏10 KB

1) product code 059B7W0
2) software version 111.030.0609
3) it is actually stored .flv files on my phone workes fine on symbian anna
Attachments:
Scr000003.jpg ‏17 KB
Scr000004.jpg ‏15 KB

Yet another internet problem after updating to Leopard

Similar Messages

Maybe you are looking for