Yoga 2 Pro Hard Drive not recognized

I got my Yoga 2 Pro as a Christmas present and have had issues with the computer recognizing the hard drive every time it boots up or enters sleep mode (and this is after the 1 initial boot up where I didn't have to enter the BIOS). Not sure if this is a bios or hardware issue, but I can get it booted after entering the BIOS, changing various (seemingly random) settings (UFEI/Legacy support usually) to get the computer to even recognize that it has a hard drive installed at all. Once it does boot, as long as it doesnt sleep or shut down, it'll continue to work, leading me to think this is some sort of BIOS issue. Has anyone been able to resolve this issue without the hassle of returning it to Lenovo an getting a whole new one? The computer is great, when it boots up, but this is extremely disappointing/frustrating to have to enter the BIOS every single time I want to turn the computer on to use it!

@Lenovo Support - Please respond to this issue.
SO MANY PEOPLE HAVE FACED THIS ISSUE & ARE STILL FACING - BUT NO RESPONSE FROM LENOVO SUPPORT...... !!!!

Similar Messages

Hard drive not recognized during windows server 2008 setup

hard drive not recognized during windows server 2008 setup

Hi,
Whether the hard disk is recognized in BIOS?
Connect it to another computer to see if it could be recognzied incase the cause is the disk itself. Also please check if it is really a RAID instead of a single hard disk - a single disk should be recognized directly while RAID cannot be recognized until
a suitable driver is installed.
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Advanced Format Hard Drive not recognized by HP DV6000 Controller

Hello,
I have an HP DV 6000 laptop (6276 I think, I'm at work can't check) that came preinstalled with a Western Digital 160gb 1.5gb/s 5400 RPM drive (Vista) that failed a couple of weeks ago. So i bought a Western Digital 750 GB WD Black SATA III 7200 RPM 16 MB drive to replace it. I read about people having some problems with Advanced Drive Format hard drives not being recognized by their controller, but also read that depending on the controller and specific Dv6000 model laptop they had-one wouldn't run into problems.
Well sure enough, when attempting to install Windows 7 I received the error that the hard drive was not detected. After researching online I came across an article on WD's site that noted
"Our SATA II hard drives use autospeed negotiation. This enables our SATA II drives to automatically detect the motherboard data transfer rate, making it backward compatible with SATA I data transfer rates. However, some older SATA I controllers are unable to support autospeed negotiation and cannot recognize the drive. This “drive not detected” condition occurs when a chipset is incapable of correctly negotiating the data transfer speed with a SATA II hard drive."
my drive is a SATA ||| but I'm pretty sure it's the same problem. The site goes on to say a fix would be to "purchase and install a third party PCI or PCI-Express Second Generation Serial ATA controller card for your Serial ATA hard drive(s)."
My question(s) are.
1)Is the problem that I am trying to install a Sata ||| hard drive on a laptop with a controller that will only recognize SATA | hard drive?
2) Or is the problem that the hard drive is an Advanced Drive Formatted hard drive and I need to buy a hard drive with out that specification?
3) Or Should I buy a SATA controller card as WD suggests on their website and if so will this definitely allow my laptop's controller to recognize the new hard drive and proceed with the installation?
4)Or Should I just return the hard drive and buy a SATA | non Advanced Drive Format hard drive? (question 2 basically)
Thanks for your help!

Hi @jasmine00
Welcome to the HP Support Forums.
I certainly understand your issue with the drive upgrade. Unfortunately it is a bit of the nature of notebooks, the sacrifice of a large amount of upgradeability, in exchange for compactness and portability. Whenever a new technology comes out, older notebooks are never really going to be easy to upgrade, it at all. Normally the unit as a whole is tested with a set list of hardware, and only those items are supported.
That being said there is this document that could be helpful with your problem.
Preparing Advanced Format hard drives for Microsoft Windows installations on HP Business Notebook PC...
And for your reference:
HP Pavilion dv6000 Notebook PC Maintenance and Service Guide
Malygris1
I work on behalf of HP
Please click Accept as Solution if you feel my post solved your issue, it will help others find the solution.
Click Kudos Thumbs Up on the right to say “Thanks” for helping!

What are the symptons of macbook pro hard drive not running fast enough

what are the symptons of the hard drive not running fast enough

Physically the drive will be as fast as any other of its class, and if not then it's experiencing a mechanical issue that should prompt a warning or two in the system, especially if you use a drive management tool like Disk Utility that checks the drive's built-in "S.M.A.R.T." diagnostics.
As for "logical speed," if there are bad blocks on the drive where sectors cannot be read or written to because of a breakdown of the storage medium, then this can result in a program or the entire system crashing or hanging (generally the latter is the case), where it usually pauses for a number of seconds at a time. This is usually accompanied by messages that state "I/O Error" or other similar warning in the OS X Console (in the Applications > Utilities folder).
Beyond this, drive formatting errors such as might happen after a crash or power outage can result in similar hang-like behavior, though this is usually not as distinct of a hanging behavior as is seen with bad blocks.
Finally, if the drive is simply full of files or highly fragmented (not as much of a problem in OS X, but it can happen), then this can reduce access time for reading and writing files, and prevent the system from optimizing the use of RAM, which can result in overall slowdowns. Heavy drive use can also cause similar bottlenecks, but this is ususally only an intermittent issue during a time when you are performing a heavy file transfer or copying process, or other task that occupies access to the drive's index and formatting (e.g., if you check it for errors with Disk Utility, then you may see the system pause or slow down during the check).

Yoga Pro 2 - Display not recognized in windows (Driver or Hardware issue?)

Out of warranty by a month!
Yoga Pro 2 - 256gb, installed new wireless card a month ago. Windows 8.1
The touchscreen still works while the screen is black.
System restarted after sleep mode I think.
The Lenovo logo is displayed, seems to load windows, but when windows loads (I don't see it load so this is an assumption) the screen blanks and the black light is on.
I can connect an external monintor which will connect after a return from sleep mode(odd). Which then turns the backlight off.
When on the external monitor the internal display is not even recognized by windows.
When I boot in safe mode, the internal screen works fine with of course limited capability.
I have reloaded display drivers from the support site.
Right now my internal monitor is not recognized by windows and is dark, and I can use an external monitor.
Anyone have any clues as to what my be going on? Hardware, driver etc???
What information can I provide?
Solved!
Go to Solution.

This is a pretty weird issue with conflicting observations.
1) Screen works in Safe Mode but not in regular boot. (So, not hardware issue)
2) Display works on external monitor in regular mode. (So, not drivers issue)
Did you install the wireless card yourself? Did you unplug the display cable while installing the card?
Could you re-open and check that all connections are good?
Is the Wi-Fi card working well?
I would also recommend a complete reset of the laptop to eliminate the possibility that this is a corrupt driver. You can use the NOVO button to reset your laptop. Make sure to make a backup on external drive for your personal files.
Current System - Lenovo Y510P, GT755M SLI, 8GB RAM, 1TB HDD + 24GB SSD
When your plans fail, your Real Story begins!!

New WD Scorpio Black 750GB hard drive not recognized

Hey guys,
I've purchased a WD Scorpio Black 750GB hard drive for my newly acquired MacBook Pro 5.5, 2.26 GHz Intel Core 2 Duo. The hard drive is installed (internal) but not being recognized by disk utility. Browsing on Google, I've found this to be a common occurring problem but as there were no direct solutions, I'm posting this in case anyone has any solutions to this issue.
I've reset the PRAM/ NVRAM with no avail. Any assistance would be greatly appreciated.
Cheers

Your response is not 100% clear to me.
Have you actually installed the WD and Seagate HDDs in the MBP or just connected them while in an external enclosure?
When you put the original HHD back in the MBP, it is recognized in Disk Utility but cannot be repaired? Is that the case.
Have you tried to put in the original Installation disk and has the original HHD been recognized and/or one of the other HDDs in an enclosure been recognized?
Ciao.

Lacie 250GB External Hard Drive NOT RECOGNIZED

HELP! My Lacie External HD that I've had for several years and holds a lot of my files is no longer being recognized on my MacBOok Pro. It used to recognize it instantly when I plugged the USB cable to the USB Port - now, nothing. The Lacie light is on, but my laptop isn't reading it at all. What's going on??? I did a disk utility - it's not showing up there at all either. Is it due to a software update? Don't get me started on losing out on using my entire Dreamweaver/Flash Studio MX 2004...
ALSO, I notice my iPhone is not being recognized in iPhoto anymore either. It is recognized in iTunes. And yes i've heard many folks say email photos should be removed, which i have done so and still nothing!
HELP PLEASE!!!

Are other USB devices working normally, Eric?
If so, the most likely cause is that either the bridge or the drive itself in your external enclosure has failed (assuming you have tried a different cable)
No, it is most unlikely to be due to a software update. With an old external drive like yours the most likely explanation is that it has simply failed. If it is the bridge, rather than the hard drive itself, that has died you may be able to remove the HD from the LaCie enclosure, put it in a different enclosure, and recover your stuff. In some cases, too, a drive light will illuminate when the drive is connected to the computer, even if the power supply to the drive itself is faulty. You might want to contact LaCie to see if they have any advice to offer about such situations.
Have you tried the drive on another Mac or another drive on this Mac? THis would immediately narrow down the location of the problem, of course.
Cheers
Rod
Message was edited by: Rod Hagen

Macbook Leopard Update- Hard drive not recognized?!?!

Question- What do you think caused this problem, and how can I best fix it?
(See below for information)
Well, I finally decided to update to Leopard. I put the disk in my Macbook, and everything went smoothly as it verified the installation DVD- until the end of the verification, that is. A message screen would pop up telling me the disk was dirty. "Okay," I thought,"No problem." I was a bit puzzled, though, because the installation with the same Family Pack disk went fine on my father's Mac. I cleaned the disk, and tried again. And again. Each time, I was greeted with the same message at the end of the verification. Frustrated, I took the disk and my laptop to Best Buy, hoping someone could help me there. We ran the installation again... to no surprise, the same problem occurs. This time, though, when we quit the installer and try to reboot, after the gray screen with the apple at the beginning, we are greeted with a black screen with one command line. NOT GOOD! We rebooted the computer again, this time starting up with a disk to check the permissions and hard drive. The diagnosis: The permissions on my Mac are screwed up, so it's not recognizing the hard drive. The Best Buy guy claims the permissions have been messed up since I bought the Mac, and everything will be just fine and dandy after I transfer the data to another computer, install the Tiger disk that my Macbook came with, update to Leopard, then transfer the data back to my Mac. I'm taking my Mac to the closest Apple store (about 2 hours away) for advice from the pros on Saturday. Until then, I'm hesitant to even turn the thing on, out of fear it will spontaneously erase the data or something to that extent.
Question: (in case you forgot)What do you think caused this problem, and how can I best fix it?

Unplugging worked!!!
I have no idea what PRAM is but someone said that unplugging your computer resets it so, I thought I'd give unplugging a shot. So, I shut down my computer and unplugged it. I also unplugged the power on the HD. (because I wasn't sure which one they were talking about.)
Anyway, I went away for about five minutes.
I came back plugged in the HD power first. Then, I plugged in the power cord for the computer and turned it on.
As soon as I logged in I was asked if I wanted to use my external HD for Time Machine backups.
I saw the icon for the HD on the Desktop where is belongs. I can open the drive and access the files with no problem.
Try this if you haven't yet.

Hard drive not recognized when connected to Apple keyboard

Hi there,
I'm using a dock (Henge) for my MacBook Pro with a wired Apple keyboard to which I connect a Passport hard drive using the USB port (my Time Machine backup). The hard drive is self powered but still it won't be recognized by the Macbook Pro. I have used the USB port to connect my iPhone without any issue.
Any ideas? Should I use a USB power booster?
Thanks
CB

The USB ports in the Apple keyboard are NOT powered, so your passport HD will not work on it because it pulls too much power from the USB port.
More info here: http://support.apple.com/kb/HT4049

Hard drive not recognized in disk utility

I'm trying to replace the hard drive in my MacBook Pro , the old hard drive was not recognized in disk utilities after the computer crashed .After installing a new hard drive and booting from the original Mac OS install DVD,( leopard?) the new hard drive is not recognized either ? Help

It may be the internal connecting cable that is the problem. If you can install the new HDD in an enclosure, connect it to the MBP, then see if you recognize it using the OSX installation disk. If so, the internal connector should be replaced.
Ciao.

External Hard Drive not recognized.

Hello everyone,
I have a probem where my external hard drive is not being recognized by my late 2009 iMac.
The hard drive is an OWC Mercury Elite-AL Pro connected to the firewire port.
It was working fine till this happenend:
I keep all of my iTuned music on the external hard drive.
I was using a meta tag fixer type program.
I dragged the files from itunes into this program (Tune Up) to fix the meta tags.
However, I missed the program and dragged thusands of .mp3 files onto my desktop.
My computer, of course, became unresponsive.
So I used the power button on the back of the iMac to shut it off.
I used my MacBookPro to connect to my iMac as a target drive, and deleted all the .mp3's from the desktop there.
Once I restarted my iMac everything was fine, except that the external hard drive has not been able to be recognised ever since.
The same drive shows up just fine on my MacBookPro.
Help!
Thanks!

I had the exact same problem! I had to force shut down my iMac (24in, Mid 2007) due to a system freeze. After restarting, everything was working fine, except for my external 1GB G-Drive, which was connected through FW800 port.
The drive connected fine to my MacBook Pro, but it would not be recognized by my iMac. I tried restarting, but neither Disk Utility, nor System profiler would see the drive.
What worked though, was Resetting the System Management Controller (SMC):
1.          Shut down the computer.
2.          Unplug the computer's power cord.
3.          Wait fifteen seconds.
4.          Attach the computer's power cord.
5.          Wait five seconds, then press the power button to turn on the computer.
The drive mounts fine now. I am surprised this is not mentioned by Apple in their support documents! It has happened twice to me and it was the only thing worked both times. The link for the resetting the SMC is here:
http://support.apple.com/kb/HT3964?viewlocale=en_US&locale=en_US
Hope this helps solve your problem too.

Thunderbolt Hard Drive Not Recognized

I've got a brand new Seagate Backup Plus 1tb hard drive and when I plug it in to the Thunderbolt input on my Mid 2010 Macbook Pro running Lion, it's not recognized in Finder. I looked in Disk Utility and it's not there. I looked in About this Mac and the Thunderbolt option under the Hardware section says that nothing is connected to the port. Could someone please help me out here? Does having a Thunderbolt port actually mean that it workds? I'm being a bit naive here. Thanks for your kind help.

2010 Macbook Pros don't have Thunderbolt. They have a visibly-identical mini-Displayport connector, but that's just for displays. If you look at the small icon next to the port, a Displayport icon is square, a Thunderbolt icon is a lightning flash.
Matt

External hard drive not recognized in Finder or Disk Utility

Two weeks ago, my 2007 black Macbook stopped recognizing the hard drive. I was told by some IT friends that the controller had likely failed and I needed to purchase a new laptop. I removed the hard drive and placed it into an enclosure (turning it into an external hard drive) and hooked it up to a new Macbook Pro which I purchased a couple days ago. The external hard drive did not show up in Finder or Disk Utility but the light on the enclosure was on and it was making a very soft whirring noise and got warm after a few minutes. I usually backed up the hard drive but, of course, hadn't done it in a couple of weeks before it died so everything I worked on in that time is lost to me at the moment. I'm trying to avoid paying tons of money for a data recovery service so any advice would be greatly appreciated! Thanks!

That whirring noise might be due to physical damage on the disk. I know data recovery services are costly but that remains only the solution for damaged HDD. You can get latest quotes on services from different dealers. Proceed only when your data is very important to be recovered.

External hard drive not recognized on new macbook

we have an external harddrive that we used as the time machine for our previous imac. we just bought a macbook pro, and the harddrive is not recognized and does not show up on the sidebar. it is however shows up on disk utility but i dont know what to do with it/how to get files from my old time machine. please help! thanks

The hard drive will not show up on the sidebar or desktop unless Finder preferences are set to do that:
In Finder's General preference section, make sure "External disks" is checked in the list of things to show on the desktop if you want to see them there.
Likewise, in Finder's Sidebar preference section, make sure "External disks" is checked in the "DEVICES" section to see them automatically appear on the sidebar.
But you don't need to do either for the MBP to recognize the drive, or to get files from its Time Machine backup set. To do that, you should use the Time Machine "Star Wars" interface. Pondini's FAQ's (already mentioned) tell you how to do that. Tip 17 is particularly relevant.

WD external hard drive not recognized after improper eject

I have a WD Passport external hard drive that I've been using for a while with my MacBook Pro. The cord got yanked, causing the drive to improperly eject. Now my computer isn't recognizing the HD. Help! Of course EVERYTHING important is on this drive!
I tried plugging it into a Mac desktop, which also did not recognize the drive.
I plugged a different Passport into my MacBook Pro, and it was recognized, so I know it's not the USB Port that's causing the problem.
I used the cord from the HD that mounted with the problem HD. Didn't mount with the new cord. So I know it's the passport that's causing the problem, not the MacBook, not the USB port, not the cord.
I ran the disk utility, and the HD does not appear...It is powering up though- the light on the HD is lighting up. Oh please help!
Did I kill my disk? Of course I just moved my entire iPhoto library to this location, and I haven't backed it up yet....

No. It may just require a 00 Phillips driver depending upon the enclosure. Do the swap on a towel so that the little screws don't bounce away from you. You will have to pull the HDD out from the connecting plug. Do it in a straight line,don't bend it, and you may have to slowly increase pressure to get it out of the connecting plug.
It's not rocket science.
Ciao.

Yoga 2 Pro Hard Drive not recognized

Similar Messages

Maybe you are looking for