Yoga 3 pro win 10 update

I had a couple of issues after a win 10 STD upgrade from USB lash drive. Windows update wouldn't run at all. I needed to completely turn off Use Account Control and then rerun windows update. It would then start, but the update process failed. I ran the troubleshooting app in the control panel for windows update, which fixed the problem. I could then turn UAC back to where it was. I also have 2 problem devices in device manager, which I haven't fixed yet.
Serial IO 12C Host controller
Unknown device on ACPI-compliant embedded controller
After 24 hours, I have had a couple of times that the machine hung or crashed, and needed to be rebooted.

Hi guys,
I am trying to update my Yoga 3 Pro 1370 for a week know, maj be 5-6 times without any success. I was fixing the errors one by one, downloaded may a doze of times the instalation.
The latest error is C1900101-4000D.
I've tried everything which is on the internet withou any success.
Any suggestions?
I've updated the bios, downloaded it few times, reset the buffers, cleaned the temp folder etc... no success.

Similar Messages

Ready to install fresh win 8.1 on new Yoga Pro 2

So, I just got my yoga pro 2 Friday. Can't stand the extra stuff and 7 particians.
I've got a usb stick with a copy of win 8.1 on it. I can boot to it and get the windows installer started ( I stopped at the partiican table)
I got the drivers folder from the D: on the yoga backed up.
Got my win 8.1 pro product key written down.
Don't think I will need any of the lenovo apps.
Nothing else I need, right? I did actually make a system image of the fresh install on another external drive when I got it, so if i did need to go back, I can.
The windows installer will take care of all partiicans, correct? I'm new to EUFI boot. I can see that legacy mode is disabled in the bios now.
Thanks for any help. Looking forward to a clean install. Wish I could have gotten this from a MIcrosoft store instead so I don't have to deal with it.
Solved!
Go to Solution.

seems you're already ready.

New user of Yoga pro 3 : trackpad gestures and win 10

Dear all, I just got my Yoga pro 3 and coming from a Mac, I am a bit lost (I use Win 7 at work). One thing that I miss the most is the track pad, although the Yoga's seems to be quite good. However, I thought there would be 2-3 finger gestures, and apart from 2-fingers scroll, which is fine, I haven't found anything. Do I need to install something? The thing I really need is a 2-finger Right click, as in a Mac (I am so used to it!)...the rest I can live without.
FInally, I was thinking about upgrading to Win 10: do you recommend it? Is it worth it? Also, how to do it? I thought I would get a "Get Windows 10" icon (my wife does in her 4 years old laptop) but I do not.
Thanks for your help!

Thanks ! Indeed it works but I must press really hard! I was more thinking of something like the 1-finger press but I guess I wil make do with it...

Windows 7 PRO GP update error

Windows 7 PRO GP update error
We have a very peculiar problem
We have a Primary DC & Secondary DC installed in all our office ( Windows 2008R2). The Domain name is abc.com for all the Offices and the replication between the DC's happen in between the office happen without a problem.
The clients in each of the offices gets authenticated from the DC in the respective office.
But for a group policy update it gives an error as below
"Computer policy could not be updated successfully. The following errors were encountered: The processing of Group Policy failed. Windows attempted to read the file
\\<FQDN>\sysvol\<FQDN>\Policies\{BD732AAF-016F-11D2-945F-00C04Fb984F9}\gpt.inifrom a domain controller and was not successful. Group Policy settings may not be applied until this event is
resolved. This issue may be transient and could be caused by one or more of the following:
a) Name Resolution/Network Connectivity to the current domain controller.
b) File Replication Service Latency (a file created on another domain controller has not replicated to the current domain controller).
c) The Distributed File System (DFS) client has been disabled.
The error happens only on some clients.
We are able to Ping, connect to the local DC and the client gets the IP from the local DC and also gets authenticated by the local DC for log on.
On the PC which gives an error if we try to ping domain name - abc.com it returns the ip of the DC in a another office and not the local DC.
Request to suggest a solution / tips to identify the problem

Thanks for your reply
Please find the IPConfig Details as requested
Windows IP Configuration of CLIENT with Problem
   Host Name . . . . . . . . . . . . : NP
   Primary Dns Suffix . . . . . . . : ALT.COM
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : ALT.COM
Ethernet adapter Local Area Connection 2:
   Connection-specific DNS Suffix . : ALT.COM
   Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
   Physical Address. . . . . . . . . : 00-19-99-F2-5B-BC
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::bc5c:5976:37b2:d42a%14(Preferred)
   IPv4 Address. . . . . . . . . . . : 10.102.22.72(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Tuesday, July 08, 2014 8:02:23 AM
   Lease Expires . . . . . . . . . . : Wednesday, July 09, 2014 8:02:23 AM
   Default Gateway . . . . . . . . . : 10.102.22.1
   DHCP Server . . . . . . . . . . . : 10.102.10.10
   DHCPv6 IAID . . . . . . . . . . . : 318773657
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-FE-B8-99-00-19-99-F2-5B-BC
   DNS Servers . . . . . . . . . . . : 10.102.10.10 10.102.10.11
   Primary WINS Server . . . . . . . : 10.102.10.10
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter Teredo Tunneling Pseudo-Interface:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.ALT.COM:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . : ALT.COM
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
===========================================
Windows IP Configuration on DC
   Host Name . . . . . . . . . . . . : ALTHODC03
   Primary Dns Suffix . . . . . . . : ALT.COM
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : ALT.COM
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Intel(R) 82575EB Gigabit Network C
on
   Physical Address. . . . . . . . . : 00-19-99-7E-7F-62
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 10.102.10.10(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.224
   Default Gateway . . . . . . . . . : 10.102.10.1
   DNS Servers . . . . . . . . . . . : 10.100.10.10
                                       10.102.10.11
                                       127.0.0.1
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.{4353BDBD-759C-45E1-A523-621CC16121AA}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Teredo Tunneling Pseudo-Interface:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
=======================================================
We do not use Sysprep and also we normally do not use imaging
Domain Time is in Sync with DC & Client

Will my MS Surface Pro Win 8.1. 64-bit run my LaserJet 3310. Where to find drivers? Thanks.

Will my MS Surface Pro Win 8.1. 64-bit run my LaserJet 3310. Where to find drivers? Thanks. Perhaps, are drivers built into 8.1 as they are for Win7?

The Laserjet 3300 Windows 8.1 x64 drivers are supplied through Windows Update as for Windows 7.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Windows sensor button on monitor stopped working - Yoga Pro 2

I have had my Yoga Pro 2 all of 3 days, and today the sensor button located on the monitor that brings you to the windows start screen has stopped working. When I purchased the laptop, the sensor worked fine - it vibrated when touched and brought me to the start screen. Now, nothing happens. I have installed the 2 updates I was prompted to install, could this be the issue? Has anyone else experienced this problem?

Dear Dettraka
Welcome in lenovo community
Have you tried to reset the machine to the factory setting ?
Thanks
Alaa
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Any fix for USB 3 port disconnects with Plugable GigE adapter on Yoga Pro 2

Hi,
Does anyone know if there is a fix intended from lenovo on this?
Very pleased overall with my Yoga Pro 2, however one issue is that I sometimes need to use a GigE adapter and the Plugable USB3-E1000 I bought will disconnect periodically - mainly an issue when using the link heavily.
It is acknowledged by plugable to be an issue:
http://plugable.com/products/usb3-e1000 "There is known conflict with the Lenovo Yoga 2 Pro’s USB 3.0 port and the USB3-E1000. Symptoms include sudden loss of connectivity and failing of transferring files across a network. The current workaround is to use the USB 2.0 port. We are working with ASIX and Lenovo to resolve this known bug."
It transmits at about 1.5MB/sec on USB2 and 15MB/sec on USB3 so a clear preference to use USB3!
Thanks
Stuart
PS RUnning windows 8. fully patched, have updated BIOS from 1.15 to 1.16

If used an external USB Wifi adapter that worked fine (Asus).
This Linksys should also work in the Yoga.
Freedom of Speech has just left the building

Yoga Pro 2 on External Monitor...but low resolution

Although my Yoga Pro 2 connects properly to my Viewsonic monitor (thank you, Monoprice, for the micro-HDMI adapter and the HDMI to DVI cable), the best resolution I can get is 1440x900 (the native resolution of the last computer connected) which makes everything look GIGANTIC on the monitor and doesn't show the detail of the 3200X1800 Yoga Pro screen.
Intel drivers are updated, Viewsonic monitor drivers for win8/x64 all set. Viewsonic says it a Lenovo issue...Lenovo so far can't help me. I have tried changing view/zoom in every software program and app, but that's not the solution I want. Even 1900X ???? would be better.

PATIENCE...
First, it is most likely the microHDMI fitting inside the yogapro. It is very deep. When you put a micro HDMI adapter in to connect it to whatever it needs to connect to to ultimately reach your monitor, it must be firmly seated.And it feeels like it is..but probably not.
Monoprice.com offers 2 microHDMI adapters: part 7703 and part 7603. Either one should work...but you may need to take an emery board or nail file to the plastic housing around the actual part that goes into your machine. That's because you need a long reach to the actual socket inside the YP2. From there I use the monoprice HDMI-DVI cable to attach to my monitor (LG, but not important. Only important thing is that the ratio of width/height is 1.7778, or 1920x1080 etc)
Make sure the monitor is turned on....and start JIGGLING. Be 100% sure that the YP2 is sitting on a very hard surface, granite, corian, etc...and that the machine doesn't get moved around at all. Do not put it on a cooling pad, or a place mat or anything squooshy like that. Keep a bunch on small thin things around as you jiggle...because at some point you are going to succeed and you must not jar anything as you put the need supports to maintain that crucial angle VERY CAREFULLY in place. It is tedious...but the result is worth it. And then deciding on your personalization will keep you busy.
As much as I like the YP2 as a computer...I have never used it as a tablet (iPhone/Kindle user) and probably never will because the task of getting the Micro HDMI adapter seated properly is something that is hateful enough that I don't want to move the machine once it is working with the external monitor. Furthermore, the personalization setting are different for me with/without external monitor and not worth the hassle.

Yoga Pro 3 Touch Pad Not Working With Win10

This has been hinted around in several other YOGA Pro 3 WIN 10 upgrades but we probably need to start splitting out each particular issue. My upgraded to Win10 with no issues on the upgrade itself. I performed the upgrade with a mouse attached and now I no longer an switch back to using the touch pad. Another way to say it is that my Fn + Delete button no longer works. I checked Synaptics for a driver but they don't list one for Win10. Any one know a work around to get the touch pad working again or a suggestion to fix? Thanks

I'm in the same boat - no touchpad after upgrade. I am sure we are the first of thousands to experience this issue.

Thinkpad yoga pro 15 w/3D sense

In case someone was curious as how the Windows 10 upgrade went on a Yoga Pro 15 w/ 3DSense.
Windows 10 installed the latest graphics card drivers for Win10 but installed a slightly older version Intel driver 10.18.14.4049 instead of 10.18.15.4248 for the 5500. I have no issues with the Intel driver so I'm keeping it this way for now since it's running fine. Probably install soon.
Upgrade was pretty smooth. Only Driver hitches that I had to download after install were the 3D Sense camera driver (Camera was inoperable at first start of Win10 but no issues after installing Lenovo's Intel Win10 3D drivers) and lenovo Power Management Driver.
All in all it was pretty trouble free from what I can tell so far!
I first made sure to update as many drivers as I could from Lenovo site before the upgrade. I did have to force start the update in windows as it kept failing on it's own everyday like others have experienced.

I did not update drivers that were solely for Windows 10. I did update all other drivers listed for Win10 and Win8 you know the same driver works for both. I made sure that all drivers for Win8 were updated and no I did not uninstall any software. I did turn off my antivirus but in hinesight I would recommend uninstalling your antivirus before upgrade and download the newest version for Win10. I ended up uninstalling mine after the upgrade to install the latest verion Kaspersky. Doh! Actually should have known better. It didn't screw with the install but Win10 right away said, this Kaspersky has limited use. The one thing that freaked me out when I upgraded was the 3D camera was inoperable but I downlaod the driver firmware for windows 10 it's backup and working. So far everythings running smooth still playing around with stuff when I have the time to see if there is any glitches but so far looks good. Edit: I did update the Bios to the newest version before upgrade and that actually stabilized some issues I had with my yoga before the upgrade, lol.

Trouble with Adobe Reader Touch on Lenovo Yoga Pro 2 in tablet mode. Pdf shows up as blank pages.

I have a Lenovo Yoga Pro 2 and when I change it to tablet mode and use the Adobe Reader Touch app, my pdf shows up as a blank page. I have installed other pdfs in the past and those show up fine. However, as of three days ago, whatever pdf I install shows up as blank on my screen. Is there a solution to fix this?

Could you please share your test file?
You can send the file at [email protected]

What type of ssd does yoga pro 3 have?

Is it MLC or TLC? I heard people say yoga pro 3 uses sumsung SSD, and sumsung like using TLC which i dont prefer.

Samsung or LITE-ON, per the Hardware Maintenance Manual:
http://download.lenovo.com/consumer/mobiles_pub/lenovo_yoga_3_pro_1370_hmm.pdf
I don't work for Lenovo. I'm a crazy volunteer!

Support problem. The adviser tried to diagnose the failure of an application called JOTNOT PRO to update. He said he'd phone back at 8pm. I pick up his call at 8pm. Electronic voice: thank you for calling apple. We are now closed" So now I have 2 problems

Support problem. The adviser tried to diagnose the failure of an application called JOTNOT PRO to update. He said he'd phone back at 8pm. I pick up his call at 8pm. Electronic voice: thank you for calling apple. We are now closed" So now I have 2 problems: the adviser had got me to reset so bye bye wifi passwords and settings. And then when he phones back as we agreed he's not actually on the phone, it's just a voice saying Apple Support is now closed! What on earth is going on at apple support I wonder.
Anyway, the original problem: an application called JotNot Pro fails to update. The error message says something like "you cannot update this cos either you bought it with a different Apple ID or somebody else bought it."
Neither applies. Can anybody help?
PS. This is my first approach to the support community so please bear with me!
William

You might have better luck contacting the app's support or developers.

I have a late 2008 Macbook Pro last updated to Mavericks OS. The screen died and it's not worth replacing. How do I remove the hard drive and use a drive sled to access info I need?

I have a late 2008 Macbook Pro last updated to the Mavericks OS. The screen died and I took it into an Apple store and was told replacing the screen and the hardware to repair everything would cost almost as much as buying a new laptop or a cheaper model. I was told that I can use a drive sled to access data I need on my hard drive. How do I remove my hard drive and use a drive sled to get to the information I need? What makes matters more complicated is I need to update my iPhone and my iTunes/App store purchases. How can I accomplish this?
My wife has a late 2008 Macbook Pro as well, which I am assuming I need to run my hard drive. Is there a way to just access just my hard drive without interfering with hers?
I know this is lengthy. Thanks to whoever looks at this and offers advice/instruction.

the device you need is an External enclosure for a 2.5" (laptop form factor) SATA drive.
A USB-interface enclosure will be slow, but is adequate for this task and for re-purposing as a backup drive later. A firewire-interface drive would be faster, but is harder to find, more expensive, and faster than needed for this purpose.
The drive will mount as an "extra" drive on your wife's Macbook, and you can drag and drop whatever you wish. You could create a separate Account for yourself on her computer, and use Migration Assistant or just copy your stuff over to the new account. Then it would not interfere with her files.

Yoga Pro 3 - Wifi dropped connections; refuses to reconnect

First day of owning my Yoga Pro 3. Has anyone experienced intermittent wifi failures?
I've had trouble on both access points that I have at home. One is an older 802.11b router (set to channel 1), and other a D-Link815 dual-band bgn router (with the 2.4Ghz radio set to channel 11).
I've experienced problems using both routers on either channel and when using the 5Ghz spectrum as well.
Connectivity with either access point lasts from 5 mins to 30+ mins (in limited time I had available to use it so far).
Far more frustrating is that when dropped, the YP3 refuses to reconnect. Manually selecting the access point in the network connections charm and clicking "Connect" results in failed attempts at connecting and system will refuse to connect to any Access Point for a random amount of time. At one point I had attempted to reconnect about 20+ times before it did reconnect.
Obviously, tried rebooting without any change in behavior.
I uninstalled the Broadcom wireless driver (the system the auto-installed a Microsoft driver which, from the version number, appeared to be an older version of the same Broadcom driver as they used a very similar numbering scheme and were very close). No change. I reverted that change.
Are there known issues with these wifi cards/drivers accessing open wifi connections? I live in the middle of no-where, so have had no compelling reason to secure the access points.
What else should I try?
Thanks

My WiFi connects fine @ 2.4 GHz only Access Point (netgear wnr2000 v2) 4 rooms away (~ 35 feet and my Linksys router is on the same room as me so I get 866.5 Mbps all the time), giving me fluctuating connection speed from 243 to 300 Mbps. I generally don't use the 2.4 GHz band but I occasionally try it to check for stability. It's working fine but there's too much 2.4 GHz clients in our area so I use 5 GHz for Netflix, Hulu steaming where low latency stability is needed.
Definitely try reseating the antenna so you can rule that out. If you still can't connect @ 2.4 GHz, try other 2.4 Ghz access points or it's just that you get a defectve Broadcom 4352 card or it might be even Windows 8.1 drivers itself.
Lenovo Y470: i7-2670QM | 8 GB DDR3 1333 MHz RAM | Nvidia GeForce GT 550M | 500 GB 7200 RPM Seagate HDD | ASUS PCE-AC56 802.11ac Network Adapter | Windows 7 Professional 64-bit

MacBook Pro firmware update after erase & install

Hi,
I just tried to update from 10.4.10 to 10.4.11 with software update last night and got the error message a lot of people have been experiencing, then, got stuck at the apple logo with the never-ending spinning wheel... well... tried repairing disk, permissions, everything, but didn't work...
Now I reinstalled OS X with the dvd that came with my pro (10.4.6) and I noticed that when I run softwarte update, a specific MacBook Pro firmware update and some battery update didn't show up, does that mean I already have it? because it is firmware, the installation of OS X didn't erase it?
And to all those out there stuck at the boot screen, I'm trying the manual combo update (downloading from apple.com) and will tell if this works (thank god I backed up everything!)

Good Morning,
To answer your firmware question, yes. Once applied a firmware update is burned into the chip on the device being updated and is not subject to being removed with an operating system, the only way to change that firmware is to update it with something else.
You should be fine that they aren't showing up because, as you said, you already have them. 
David

Yoga 3 pro win 10 update

Similar Messages

Maybe you are looking for