Yosemite shutting down after startup

I have a 2011 macbook pro and i have a schedule set for it to come on during the morning. My mac starts up like it is suppose to do but if I don't touch it after a certain amount of time it will shut down automatically with out me doing anything. This happens no matter if i have the computer lid open or closed, yes it is on power, no i did not login. Is anyone else having this issue?

Hello, GinoS.
Welcome to the forum!
Sorry to hear that. Did something happen to the phone before the issue started? How did you reset the phone? Is it by pressing and holding both the volume down and the power button for 15 seconds, or by going to Settings, About and then reset your phone? By the way, is the phone's software updated? Updating to the latest version of your phone may resolve the issue. 
You can check: http://www.nokia.com/global/support/software-update/lumia-software-update/ on how you can update the phone's software.
Failing that, you can send the device to our Nokia Care Points for further assessment.
See: http://www.nokia.com/global/support/locations/ to know the Nokia Care Points near you.

Similar Messages

  • Quicksilver shuts down after startup chime

    Hello,
    I got an old Quicksilver 2002 (933) which won't boot : it shuts down 3 or 4 seconds after the startup chime. What's wrong ?
    Thanks

    Thank you for your answer, but it didn't work.
    I forgot something important in my first post : the story of this Quicksilver
    So yes, I just acquire this Mac, didn't work at all. It was missing a screw on the CPU card. After adding the screw, the PM booted into my Tiger DVD. I shut down the PM to close it correctly. It didn't boot anymore for this time.
    I tried PRAM reset, motherboard reset. I've taken apart all I could (modem, graphic card, hard drive, ...), I've replaced the PSU, but nothing. I noticed that when I try to boot without RAM, the powermac makes one beep (no RAM installed) but don't shut down after that ! So I tried with 2 different RAM modules on every RAM slot, but it didn't work. (each RAM module is PC133 and works fine on my iMac G3 DV SE).
    I think the motherboard or the CPU is screw up, but which one ? Maybe I forgot one thing to make it work ?
    Cheers, Aurélien
    (sorry if my English is a bit bad, but I hope it will be understandable

  • Mac air screen flickers and shuts down after startup

    I recently loaded Lion on my 2011 mac air. After a week the computer started to have slow startup's, now when i turn on the computer the screen flickers and immediatly shuts down. How can i fix this problem.

    correction the Mac Air is a 2010

  • Adobe Creative Suite Design CS6 - PhotoShop, InDesign and Illustrator immediately shuts down after startup

    I'm troubleshooting for a customer who have Adobe Creative Suite Design CS6.
    His programs suddenly wont start, they launches and starts to read plug-ins and open up a workspace, but then without warning/error it shuts down. no log, error message or anything...
    It's the same for PhotoShop, InDesign and Illustrator both in 32 bit and 64.
    He is running the suit on a Hp EliteBook 8560p with Windows 7 Pro x64 sp1.
    He also have had a Wacom Bamboo CTE 650 penpad installed before.
    This is what I've done so far:
    * Uninstall the whole suit and reinstalled it again (Done this 3-4 times, manually deleted regestry-files, used CClean and other cleaning tools)
    * Deleted the wacom-drivers with controlpanel tool, Windows driver Clean tool, CClean and manually deleted registry-keys and files.
    * Uninstall Anti-Virus software and replaced it with another, inactivated AV and Windows Firewall.
    * Deleted register-files for the suits and "reregister" them again.
    * Full patch both for windows and adobe softwares.
    * Reboot between each step
    Any suggestions?
    I have to add that adobe support for this $2000 software really sucks...
    Thanks!
    // Rikard

    Problem solved!
    I went through all the folders associated with adobe cs6 and renamed them (one by one) so they would be recreated.
    I did this before but seems like I missed this specific one.
    Anyway, when I renamed the folder "SLCache" in C:\Program Files (x86)\Common Files\Adobe\ and then ran the applications one by one as administrator I was prompted to enter a serial-key again and log in to my Adobe-ID.

  • 2007 Mac Book pro Shuts down at startup attempt. Tried reloading OSX and will not start up after that.

    My Mac Book Pro started having issues. I tried to relaod the operating system and it worked for a moment. When I tried to do a time machine back up it failed.
    Now itr Shuts down at startup attempt. Tried reloading OSX and will not start up after that.

    Dr.Conga,
    did you try to do a Time Machine backup from your MacBook Pro, or a Time Machine restoration to it?
    Are you trying to reload your current version of OS X (10.7.4, to judge from your signature), or are you trying to reload the version of Mac OS X that came on the grey installation DVDs that originally came with your MacBook Pro?

  • 2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior.  No system changes.

    2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior.  No system changes.

    2008 Mac Pro 10.5.8 shuts down after hours of no use, Set to never shut down. Can be resumed pressing any key but all programs not in startup list need to be restarted and unsaved data lost .   New behavior.  No system changes.

  • My computer shuts down after about two minutes of use or at startup. What is the problem?

    My computer shuts down after about two minutes of use or at startup. What is the problem?
    Yesterday I used it for about ten minutes.
    Yesterday was the first time using it after about 5 days.

    Could you tell me how to check my system log, and how to tell if it is the disk cache? I am pretty sure it is not the GPU as I was having the problem using a Quadro 4000 as well.
    Thanks!

  • My Mac book pro shuts down after starting

    My Mac book pro shuts down after a few second. I have to press the start button multiple time before uploading

    MacBook Pro (17 -inch, Mid 2009) OS X Yosemite Version 10.10.2
    Processor 2.8 GHz Intel Core 2 Duo
    Memory 8 GB 1067 MHz DDR3
    Startup Disk Macintosh HD
    Graphics NVIDIA GeForce 9400M 256 MB
    Serial Number W8******8YB
    Disk Utility Message:
    Repairing permission for "Macintosh HD"
    Warning: SUID file "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOSARDAge nt" has been modifiedand wil not be repaired
    Group differs on "Library/Printers/InstallerPrinters.plist";should be 80; group is 0.
    Permission differs on "Library/Printers/InstalledPrinters.plist" should be -rw-rw-rw ; tey are -rw-r---r--
    Repaired "Library/Printers/InstalledPrinters.plist"
    Group differs on " Library/Preferences/com.apple.alf.plist" should be 80; group is 0.
    Repaired "Library/Prefernces/com.apple.alf.plist"
    User differs on "private/var/db/displaypolicyd"; should be 0; user is 244
    Group differs on "private/var/db/dispaypolicyd:; should be 0 group is 244
    Repaired "private/var/db/displaypolicyd"
    Permission repair complete
    I was not able to fix the problem,
    TinTin 15
    <Personal Information Edited by Host>

  • Mac shuts down after boot. Is it the logic board?

    mac shuts down after boot. Doesn't go beyond gray screen with apple.  Is it the logic board?
    I do not have the start up disks to safe boot or check the hardware.
    Any ideas what the problem is or is it junk?  It is 8 years old.

      Shutdown your machine.  Hold down the shift key.  Poweron.  Wait awhile Wait awhile while you harddrive
    is being checked.
        http://support.apple.com/kb/ht1455
    I'd let the machine sit for awhile in open firmware & see if it stays alive.  Do a few prints.
    Sometimes if volumes don't appear in Startup Manager (what you get when you hold down the Option key at startup), you need to reset the Mac's PRAM, NVRAM, and Open Firmware. Shut down the Mac, then power it up, and before the screen lights up, quickly hold down the Command, Option, P, and R keys, until the Mac has chimed twice more after the powerup chime. Then, before the screen lights up, hold down Command-Option-O-F until the Open Firmware screen appears. Then enter these lines, pressing Return after each one:
    reset-nvram
    set-defaults
    reset-all
    "The reset-all command should restart your Mac. If so, you have successfully reset the Open Firmware settings."
    http://support.apple.com/kb/TS1812?viewlocale=en_US
    How to eject a cd from the internal cd drive:
    eject cd
    List of devices:
    devalias
    Restore Tiger 10.4 & Leopard 10.5  DVDs are available from Apple by calling 800-767-2775 as of January 20, 2013.
    https://discussions.apple.com/thread/4720126?tstart=0

  • IMac keeps shutting down during startup loading bar under apple sign

    My electricity went out and came back on a minute later. When my computer started up again the font was back to original factory setting. I then restarted my computer and every time it would load up it would shutdown. The computer chimes and then reaches a grey screen with an apple sign. Below it is a loading bar. This bar loads about 10% then goes back down and loads from 0%. A couple minutes later it shuts down after staying at 0%. It keeps doing this routine every time I start the computer. I then did a command s and rebooted the computer to factory reset it. The computer still shuts down and has the old habit of reaching 10% and 0% with the loading bar but now after the loading bar is at 0% it then disappears to the Apple sign and a loading circle. It then shuts down again. This iMac was originally 10.6.8. but i believe i updated it to 10.9.4 and was purchased new around 2008. I also tried to put in a CD with Firmware Restoration CD 1.7. but that didnt work. Can anyone help? or has anyone had similar issues?

    Hello canwary
    Good job on troubleshooting your issue so far. For most issues that deal with your Mac not starting up, consult the article below to see what the issue could be. 
    Mac OS X: Gray screen appears during startup
    http://support.apple.com/en-us/TS2570
    Let me know if this helps,
    -Norm G. 

  • Computer shuts down after connecting i-pod

    my computer shuts down after i connect my i-pod nano new gen.
    also tried to connect before computer is on but then my comp shuts down at login page.
    after a few tries the computer stays on . but if i disconnect and connect again computer again shuts down.
    i reinstalled drivers but nothing seems to work.
    also when i manualy start i-tunes and then connect the i-pod the comp also shuts down.\
    anyone a idea?
    thnx in advance

    Are you getting any sort of blue screen before the PC reboots? If so, what numerical and text codes are you getting with it? (ie 0x\[zeros/letters/numbers] CAPSANDUNDERSCORES)
    If the blue screen mentions a specific file (for example, “ati3duag.dll”), let us know what that is called too. (Exact spelling, please.)
    Here's a reference on the sorts of things i'm asking about:
    Troubleshooting Windows Stop Messages
    If you're not seeing a blue screen (or if you’re just seeing a flash of a blue screen before the PC reboots), we can use the following technique to make hidden blue screens appear for us:
    1) Open your system control panel (Start->Control Panels->System).
    2) Select the "Advanced" tab.
    3) Click the "Startup and Recover" section's "Settings" button
    4) Verify that under "System Failure" the "Automatically restart" checkbox is not checked.
    With those settings in place, does a blue screen appear before the PC reboots?

  • MacBook Shuts down during startup

    My MacBook started acting slow the other day and then today when I started it up, it was in a constant lock up with a spinning pin wheel. No force quit commands or anything would work. So, I restarted it and now after the Grey screen with the Apple logo, the MacBook shuts down. The only thing I can get running is by holding C with the Leopard disc in there.
    I tried to run Disk Utility from there but everything failed. I'm assuming I need a new hard drive? Is there anyway to save data from within the Leopard disc bootup? Maybe over a network?
    Thanks

    Hello,
    I am having this very same issue. It shuts down during startup. I can boot into Windows, and using the Leopard startup disc, Disk Utility could not work any magic. I do not have a second Mac or access to one for any backup purposes. I have no idea what else to try, does anyone know something besides backing up through firewire, on how I can either save my computer's data or resurrect the drive? Thank you for your help.

  • Elitebook 9470m shuts down after Ram Upgrade

    Hey guys
    I bought 2 Kingston 8GB Ram for my HP Elitebook Folio 9470m (Windows 8 Pro) to upgrade it from 8GB to 16GB. According to Kingstons' "Memory Search" the RAM I bought should work with my laptop:
    8GB Module - DDR3 1600MHz
    Artikelnummer: KTH-X3C/8G
    Herst.-Artikelnummer: 689374-001; B4U40AA; H2P65AA
    Techn. Daten: DDR3, 1600MHz, Non-ECC, CL11, 1.5V, Unbuffered, SODIMM, 204-pin
    I installed the two Kingston Rams and removed the one from HP because I read that the ram should be from the same brand.
    After the proper installation of the two Rams the Laptop shuts down during startup or the repair modus comes up with no result. 
    If I install the HP Ram and one Kingston Ram, everything works fine, but i can't install both Kingston rams without the mentioned problem. Why?? :-)
    Thanks in advance for your help guys!
    This question was solved.
    View Solution.

    Yes it should work. I checked the Kingston site and this memory is specifically recommended for your model. I would try each Kingston module separately with the HP module and run a memtest extended test on it.
    http://memtest86.com/download.htm
    Make a bootable cd or usb stick with memtest and run it on each module. I suspect you got a bad stick of RAM. At the least if it does not work Kingston is very reputable and they will refund your money.  Here is the memory suggested by Crucial:
    http://www.crucial.com/search/searchresults.aspx?keywords=Elitebook%209470m
    If this is the Answer you need, please click Accept as Solution so that others can find it down the road.

  • Hi my desktop starts and then shuts down after the apple logo and an oblong box appear.thanks

    hi my mac
    desktop starts then shuts down after displaying the apple logo and an oblong box.
    thanks

    Sounds like something is badly wrong with your system.  First step would be to start up from your Mac OS X install disk, by inserting the disk and holding down 'c' at startup.  Select your language, then choose Disk Utility from the Utilities menu.  In Disk Utility, choose your hard drive and click the Repair Disk button.
    If problems are repaired, try restarting and see if the problems are gone.
    If problems couldn't be repaired, you can try DiskWarrior, which can sometimes repair problems that Disk Utility cannot.  However, if nothing works, you probably are going to have to erase the hard drive and reinstall the system from scratch.  Hopefully you have backups!
    If there were no errors, or they were repaired successfully but that didn't fix the problem, then you should try booting into safe mode by holding down the shift key at startup.  If that works, you may have some bad third-party software.  What that might be is hard to say, though.
    If nothing works, try rebooting from the Mac OS X install disk again and install Snow Leopard right on top of your current system.  That shouldn't disturb your apps or data, but of course, if you don't have backups, you're in trouble if something goes wrong.

  • Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

    Hi my iMAc 27 inch starts up to the grey screen with apple logo and loading bar underneath it loads halfway then freezes up and shut down after a while please help

    Try the tips listed here Mac OS X: Gray screen appears during startup - Apple Support

Maybe you are looking for

  • SSRS Heat Map help

    Hi  I have SQL 2012 and while having a play around with a report I wanted to use a heat map ( or treemap ) as I believe it was called. Any way I found that it one of the posts here points you to http://www.sqljason.com/2012/03/heat-maps-for-ssrs-usin

  • Internal Order creation in ECC after creation of Service Contract in CRM

    Hi, I hv created Service Contract in CRM, but there is no internal order created referring this in ECC. Even no errors in CRM. What shall i chk for this. rgds, balu

  • Units in Different language from English , BI.7 version

    Hi I want to display Units in different Language Russian , Actually when i login into  Russian and execute the query  everything is converting into Russian but the Units are not converting it is showing XXXX  instead of EACH and PACK , Please someone

  • Setting up email won't work.

    Since I mistakenly wiped my phone a week ago  I cannot set up my email accounts again. I seem to remember having to use a blackberry address and then got to key up my live mail account but now i cant seem to do it. THe email account icon doesnt lead

  • Error in commitment update in SO

    Hi Experts, While creating a sales order I am getting an error as " Error in commitment update. Status being set. The order can not be delivered/billed." Please help me out.