Z1 problem turning off
After downloading some app."Pulse measure",where you put your finger on the camera and it shows beats per minute of your pulse,then it lagged,my camera crashed,camera not found,camera busy etc.I tried to turn my phone off or leload it,by it doesnt work.So i wait till my battarie became low,sorry for my english,and only after it was full low,my z1 turned on,and camera works BUT now,i cant turn my z1 off or reload it,only pressing hold button+up volum 5 sec help to switch it off.Help
You have to perform a software repair using PC companion.You might need to charge your device for about 1-2 hours before so the device has at least 60% battery.
Make sure the device is not connected to computer or laptop and turned off (sometimes you have to press power button and volume up until the device vibrates 3 times or on some devices you have to press the small button near the SIM tray or on the back of the device).
Open PC companion->support zone->phone/tablet software update->repair my phone/tablet blue highlighted.Follow the steps given,do not connect your phone until prompted to press volume down while plugging USB cable.
All we have to decide is what to do with the time that is given to us - J.R.R. Tolkien
Similar Messages
-
Problem turning off legacy filevault.
Hey everyone,
I began the process of switching over to the new filevault, but have encountered a problem turning off the legacy vault. Everything seemed to be goin well, at first. It took about 30 minutes for copying to complete during decryption. However, it has been hung up at "copying is complete..." for nearly 12 hours now and is showing no signs of moving on. I have received no errors. What can I do to maybe kick start the process again or should I just do a forced shutdown. Any help here would be greatly appreciated because at this point I honestly don't know if I have any other option than a forced shutdown.
ThanksOk, so I'm answering my own question here but it worked. I ended up doing a forced shutdown (holding down the power button until shut down initializes) from the screen indicating that "copying is complete..." When I restarted (manual restart using the power button again) the legacy vault was off and the new file vault was on and working properly. No data or settings were lost and everything was working properly.
Thank you to all of you who took the time to look at my initial question even if you didn't have an answer for it. -
Problem: Turning off/Connecting to Computer
My ipod will not turn off!! The play/pause button will not get my ipod to turn off. In addition, it's forever stuck in charging mode, draining battery until it turns off. I tried to reset it by connecting it to the computer, but it wont connect (nothing happens on the ipod or the computer) nor will it charge with the computer. Fortunately, I tried to put it into a dock charger, and that worked in charging the ipod again, but the problems above still remain.
What is wrong with this thing? Last time I used it was not too long ago, I added some songs to my ipod and everything was fine and dandy! Is it a battery problem that's affecting the ipod? Should I get the battery replacement thing apple offers (my warranty has expired).This doesn't seem to work for me. Thanks though
I made a miscomment.
The ipod turns off when I press the play/pause, but then it turns on automatically after 1 sec and says charging (if it's in the charger) or it says charged if it's not hooked up to anything.
I can't read the battery levels. -
Problem turning off video`s...sound continues to play
Hi, I am experiencing a problem when turning off a video and switching to listening to music - the sound continues to play over the music track or audiobook - is anyone else experiencing this problem? The only way I can get round it is by pressing the next/fast forward button....but then of course when I want to watch the remainder of the video it restarts from the beginning, not from where I left off! Any help would be appreciated.
http://docs.info.apple.com/article.html?artnum=302697
-
Hi,
I am trying to turn off Filevault, but when I try to do it, a dialogue box appears saying I have insufficient diskspace. The problem is, it says an additional 4080 GB are required! Unfortunately I don't have access to a drive of such capacity, and my internal drive is a mere 80 gigs. Does anyone know why this is happening?
Any advice is appreciated!It appears that it's a bug.
http://docs.info.apple.com/article.html?path=Mac/10.4/
en/mh1908.html has some information on the size
requirements, but doesn't address the problem you're
seeing. A search in thise forums for filevault
or file vault should bring up similar
problems. AFAIK, the best thing for you to do is
backup your home folder to another volume, create
another admin user account, log into the new account,
delete the problematic account without saving the
data, recreate the account, using the same
username/password combo, log into it, copy the
Most importantly, use the same UID/GID or you will end up locking yourself out of the old account and, if the account is an administrator one, you will be locked out of your Mac administration, too.
appropriate items from the backup, and don't enable
FileVault.
Ciao,
Ermanno -
Problems turning off required fields in contact forms
Hello
I have created a form using the "simple contact forms' widget, but I am struggling to turn off required fields. I can see the tick box, but it greyed out, any ideas?
ThanksThank you posting.
First name, last name and email address are the mandatory fields and can't be turned off.
Regards,
Aish -
Problem Turning Off File Vault
My computer said it would take just under two hours to turn off File Vault. The process appeared to move along as it was supposed to. After the two hours, a message popped up that "copying is complete." My computer has been stuck on that screen for ten hours. Do I leave it? The "Cancel" button is grayed out. I don't want to lose my information. Your advice would be appreciated greatly. Thanks.
How much free space do you have?
If is possible that you don't have enough free space to turn off FV because it must make an unencrypted version before it can be turned off.
Do you have backups of your data?
Allan -
Problem turning off snap to guide MX11.0.2
I am using FreehandMX 11.0.2 on a Mac G5 OS10.4.10 - I can no
longer use the view menu to show/hide guides, lock or turn off
snap. I can use the layers menu to show/hide or lock but cannot
turn off snap. I also cannot delete the Guide layer from the layers
menu. I have tried changing keyboard shortcut, deleting preference
file from settings folder but nothing works.Willem,
I don't use the F-keys in combination with modifier keys.
Opt-F1 through
Opt-F8 are used by the system. Check in System
Preferences>Keyboard &
Mouse>Keyboard Shortcuts. Mac OS uses F9 through F12 for
the Dock, Exposé
and Dashboard.
If you never use certain system shortcuts, you could disable
them in System
Prefs and thereby free them up for use in FreeHand. I have
disabled the Mac
OS Spotlight shortcuts because they conflict with the
magnifier tools in FH
and Photoshop.
Here's what I use in FreeHand (US English keyboard layout):
Grid>Show___F6
Grid>Snap___F7
Guides>Show___Opt+Cmd+;(semicolon)
Guides>Snap___F8
Make sure when setting shortcuts in FH, you check "Go to
conflict on assign"
to make sure you haven't used the same shortcut twice.
If you use a non-English keyboard layout, you might be seeing
different
results.
If you're using Entourage 2004 11.0, make sure to update to a
current
version, because there's a known conflict with keyboard
shortcuts in Adobe
apps there.
Judy Arndt -
6300 problem - turning off - help!
Hi
This morning I woke up and my mobile was off.
I turned it on at the top and noticed the battery was full - strange.
When I try to go into my messages it says 'Message storage memory not available', after a few seconds the messages appear again.
Once the messages have appeared, on the main screen in the top left hand corner an envelope appears (like I have received a message) this then turns round to be a paperclip. Then a 'G' in a box appears to the left of this other symbol.
These symbols then disappear, then reappear 3 times before the phone turns off again.
Any ideas what could be wrong?
(Sorry to have gone on a bit, just want to make sure I provide all details in case it helps)
Thanks so much!you can try updating your phone to the latest firmware using the NSU that normaly resolves the reset/shutdown issues.
as far as the message storange message is concerned that is because the handset is still loading and can take a few mins for the memory to fully load this happens on most of the newer nokias.
the symbol u are seeing with the paper clip rotating means that an multimedia message is trying to be recieved by your handset and the G in a box means the handset is using the GPRS connection to receive this.
my conclusion to this is the settings for the MMS may not be on the handset correctly causing it to shut down.. so i would contact your provider to recieve the latest settings... also a software update would be advisable to resolve the resetting
NokIA 5310XM V5.81 - 06-02-08 - RM-303 - 8GB microSD -
Problem turning off the PC and restarting
HI, I ve a Laptop Toshiba Satellite Pro M 30 with Windows XP PRO and everytime i'm restarting or turning off the PC a window appear saying '' End program- Sample, This program is not responding'' and everytime i have to click ''End now'' If somebody could help me i ll be very grateful.Thank you very much and sorry for my english.my e-mail is [email protected]
Hi
I have found a posting about the same issue:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=5892&messageID=20224
This happens if some different applications run in the background and cannot be disabled. In my opinion you should check the background processes and shut it down manually. -
Battery Problem - Turning off with 60 % left
Hi
I am having an issue with my 2009 Unibody 13" macbook
I have had absolutely no issues at all since I bought it and the battery life up until now has been amazing.
However the last 2 days I have had something strange happening... when I charge the laptop fully (100% shown in bar - green light on AC adaptor)....
I then use the laptop on battery - it tells me I have the normal amount of time remaining on battery power - it gets down to anywhere near 60-65% left and suddenly turns off...
It is the dead - not even in dead sleep until I plug in my AC adaptor again...
My battery info is below:
Battery Information:
Model Information:
Serial Number: 9G85201ZQ3NYB
Manufacturer: DP
Device name: bq20z951
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 002a
Hardware Revision: 0005
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 2132
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 3093
Health Information:
Cycle count: 210
Condition: Normal
Battery Installed: Yes
Amperage (mA): 757
Voltage (mV): 12171
As you can see this all appears very normal? Is there a fault with my battery?
It is only just over 2 years old - and I have had laptops before and always ensure I cycle the battery when using it - full charge, use of battery, full charge, etc...
I will not be able to calibrate the battery as it says on Apple support because the battery just turns off when it gets to 60-65%...
Any help would be appreciated...
Thanks
JohnThanks Andrew...
I have done an SMC reset and it is now running on battery currently run charge down to 50%
So it is at least better, but I will run it flat, then charge it...
Ironically I think the SMC thing might have something to do with why it took over 6 hours to charge last night!
I will reply back so people can learn from my experiences...
Cheers mate! -
Adobe Gamma problem - turned off video card
A friend (HA!) was color balancing the monitor and accidentally hit the button to turn off the video card - Now the screen is blank. Anyone know how to turn it back on when you can't see the screen? Runnng Windows XP home edition
I've never seen any evidence that Photoshop will remote OpenGL operations across an RDP link.
What functionality does a program like the RealTek OpenGL Extensions Viewer report is available to the remote session? The Microsoft software OpenGL (1.1) maybe?
-Noel -
IMessage problem | turns off after phone power off
Each time I power off my phone or it runs out of battery iMessage switches to off setting and asks me to send the activation text message. This leads to extra cost each time I close my phone. The phone also asks me for my itines password each time it is turned on.
Hi
The powersaver software is not responsible at all for this behaviour.
The BIOS is good that you checked because this would be the first thing I would recommend.
Next step is however not so funny : service.
That's the only thing to do - the machine should absolutely be able to keep working when you unplug it if the battery has enough capacity.
Software-wise there is nothing you could do since it is not involved in theese pretty low level things.
BR
Tom -
I upgraded to 4.0 and now everything wants to open in a new tab. I don't want tabs at all. How do I turn them off? I have to use IE at work and have no problem turning off tabs there, but I haven't found the way to get rid of tabs in Firefox 4.0.
That is not standard behavior. You may have installed an extension that causes it.
Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]] -
Updated with v1.2 now it won't turn off ?
Any one seen or heard of this. I ran the updater earlier to the new ipod updater v1.2 and now can't shut my ipod 60G photo off using the play/pause button or anything else ?
If you no one can help how do I go back to the older version of the updater ?Were you listening to music before trying to turn it off, or looking at photos/using it as a USB drive?
Try "rebooting" it - hold Menu and the select button at the same time for a few seconds.
My Photo has had no problems turning off that are related to the firmware - only the problems turning off related to looking at photos and using disk mode (that I mention in another thread).
Maybe you are looking for
-
Mail application is deleted how can I reinstall it?
The mail aplication is no longer visible on the icon bar and is not in the applications folder in the finder menu. Uner preferences it says that 'mail' was ininstalled or disabled so I was wondering how to reinstall it?
-
Got some avi files from a client yesterday and I am only able to hear the audio. The video portion is all white. I have tried playing the file with RealPlayer, VLC, QT Pro and Flip4Mac but nothing. I tried converting the file with Cleaner 6.5 and Div
-
I've packaged some basic Premiere Pro presets for everyone. It includes the old Film Fades from a ways back (the built-in Adobe version of the Film Fade doesn't really emulate a genuine film fade all that well), as well as some Letterboxing presets
-
After Effects Alert when opening (Error: Mount Point list is empty)
I am so confused right now. I have searched everywhere for a solution to no avail. I have a brand new Mac Pro 2.7 Ghz 12-core intel Xeon e5 with 32 gigs of ram. I installed Reelsmart's Motion blur and when I tried to re-open After Effects I got an Af
-
Hi basically I am having a designer make 2 web page back grounds for me and 10 individual images that I will use as links. What I would like to know is how big shall I tell her to make the images for the back ground pictures? I can resize the individ