Z10 - blank screen + led flashing red

On connecting my new Z10 with BBlink, was given a an option for available upgrades. On upgrading the screen went blank and LED flashes red - 3 short 2 long - blank and starts the sequence again. Am unable to restore, restart or anything. Help wanted please email.
Solved!
Go to Solution.

Glad, that you were able to resolve the problem, Hopefully future releases of the BB link would work better with Mac's..

Similar Messages

My z10 led flashing red when charging and even at battery full it blinks red. no green at any note..

My z10 led flashing red when charging and even at battery full it blinks red. no green at any notification. But at below 10% charging level it blinks with a combination of red and green. Please send me any settings to be changed if.. at full charged no green light is blinking.. how many colours does z10 led have..and when it works and how to make those settings..or was my led not working fine? I am worried so much..plz help me

Your LED is fine, on the Z10 there is not "network signal available" green LED, as you're accustomed to from the legacy devices. At reaching 10%, the LED will blink orange.
Red for message or applicaiton notifications.
if you want to edit and create specific LED color combination, see the third party apps such as BeBuzz or Hub++
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Playbook won't turn on, boot, or charge. LED flashing red.

Playbook won't turn on, boot, or charge. LED flashing red.

Try this, while connected to your charger. Press and hold the Power key, up and down volume (-/+) all three buttons simultaneously, for about 10-12 seconds. You should the red LED blink and that should allow a reset of the PlayBook and to power up.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blackberry Pearl 8100 randomly shuts off and the status LED flashes red

My pearl was reciently unlocked and changed from AT&T service to t-mobile. after this switch the pearl started having fits of rage where it will turn off randomly, weather any keys have been hit or even if it is idle. the device LED then flashes red, sometimes once, other times it will flash once every 4 seconds for hours. then it will randomly turn back on either to the exact screen it had been on before it powered off or it will reboot completley and start the normal start-up procedure and varify security checks just as if the battery were removed. i tried removing the batery and leaving the phone disassymbled for a few nights but in the morning the plague is back and unrelenting. sometimes all i have to do it pick the device up and it will shut off. other times i will be plugging away with it for 20 or so minutes on the internet and then it will die suddenly. it also cuts out in the middle of phone calls. if anyone can help,please let me know.
blackberry 8100 v4.2.1.96

Is it a new phone? If it's less then a month old see if you can return it, otherwise you can try reloading the OS.
So if you're willing to try that, do the following.
First download and install the Desktop Manager from here (4.6 without Media Manager is recommended): https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
Next you can use the Backup and Restore feature present in the software to make a backup of all the data on your phone.
Next download and install the handheld software from here: http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Afterwards try reloading the OS by connecting the device to your computer, open the Desktop Manager, then go into the Application Loader. This will open a wizard that steps you through reloading the OS onto your device. More detailed steps can be found here:
http://www.blackberry.com/btsc/KB03485
If someone has been helpful please consider giving them kudos by clicking the star to the left of their post.
Remember to resolve your thread by clicking Accepted Solution.

Led flashing red 5 times and phone unresponsive

Hi can anyone help me??
After putting my phone on charge this evening it has turned itself off and now the LED is just flashing red 5 times in a row like 1 .... 2 3 4 5. Can't get any response from it have pulled the battery and have tried connecting it to the pc but no joy. Its a Z10 only 4 months old any ideas how to fix it?

Contributor 'tezytan' is correct. Plug your phone in to your PC and open BlackBerry Link. Once your phone is recognized, you should be prompted to reload your OS. Due to your phone having a corrupt OS, it might not be recognized by Link. If that happens, leave it plugged in and remove it's battery for a few seconds; once you replace it, Link should connect with it.
Let us know if that helps you.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

K8N Neo4-F - D-LED Flashes Red through EVERY step.

I turned on my computer today and it would not boot. The D-LED shows it flashing Red for each step, then it rests on Floppy Initialization finally after one long beep. It refuses to boot up. Here are my specs:
MSI K8N Neo4-F Mobo
eVGA GeForce 6600GT
2x 512MB Kingston HyperX RAM
Western Digital SATA HDD, 300GB
Thermaltake PSU, 400W, possibly 450W, not 100% sure right now.
AMD 3800+ X2
I've replaced my HDD, Video card, USB Devices, and RAM with no luck. When removing my processor, I no longer get the long beep when the processor is out, which is to be expected. Now, I need some help here before I go blowing my money on the wrong thing. Does this sound more like my processor is fried, or my motherboard?

I am in the same boat. Computer worked fine until yesterday when it started giving a single beep and just spalshing the core cell screen up.
My computer specs are nearly identical to yours and I've been replacing things like mad. Even went so far as to try the items on another computer and had no problems, beginning to think it is the motherboard itself and not anything else.
Good luck on yours!

Blank Screen and flashing cursor on new build-P67A GD65 (B3). Help needed.

As per the title, a computer was built for me with the following specs:
CPU: Intel Core i5 2500k
Cpu Cooler: Arctic Freezer xtreme Rev 2.0,
Motherboard: MSI P67A – GD65 (B3)
PSU: Super-Flower Amazon 550W
RAM: 4GB G.Skill RipJaws-X, DDR3, 1600
HDD: 1TB Samsung Spinpoint F3 7200rpm
Graphics Card: Sapphire Radeon HD 5850 Xtreme - 1 GB GDDR5
Disc Drive: Samsung SH-223C DVD+RW
Case: Cooler Master 690 II LITE Midi-Tower
OS: Windows 7 Ultimate
Everything went ok with the build and installation of the OS. Computer was booting ok. When I took the computer home that evening, powered it on and a blank screen with a flashing cursor on top left hand corner appeared. Tried several times but failed to boot up properly. Just to note that I can enter into the BIOS and it recognizes HDD, processor, Disk Drive and RAM. What I have done so far (of course with advice from computer experts as compared to me) are the following:
1. I removed all the parts except cpu and cooler then put them back. When I restarted a message appeared that win7 need to do a repair. It went thro the process and then it stated it can’t do repair. Did this twice. When I restarted the third time, a blank screen with the blinking cursor appeared again.
2. Cleared the BIOS using the button on the outside of the motherboard and also once using the jumpers inside the motherboard. After doing this, I pressed on the “”ON” button several times (with no power on to the computer) to dissipate any current that was left there.
3. Interchanged the RAM on different slots. Also tried using only 1 stick of Ram at a time.
4. Checked the HDD on another machine and it was ok. Formatted the HDD on the other machine, plugged onto new machine and tried to install OS again but no joy.
At this point, I’m now stuck after almost a month when the machine was built. Would it be the motherboard? RAM? etc. Just wondering if I should RMA the motherboard since it is just over a month when it was delivered.
A point to note, there is a message that comes up when it is booting stating no HDD is detected. I googled this but found out it was to do with a marvel adapter that needs to be disabled or something like that. However, it was mentioned that this wasn’t going to affect the performance of the pc as the BIOS can detect all the components.
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Any help on this will be highly appreciated?

Quote
I also noticed that when I switch on the pc, there is a small pause before it kicks on then there is a long beep followed by 2 small beeps. I presume this is normal.
Disable EuP 2013 & that should take care of the pause. The beeps are normal at startup. Only time I have observed a blank screen & blinking cursor is if the system wasn't getting enough juice to initialize, or their was insufficient power in an OC attempt. What kind of +12V amps does that PSU you have provide?

Pxi 8360 power led flashes red

I have a PXI 8360 MXI Express board mounted in a PXI 1050 chassis. I am seeing the power LED occasionally flash red and I lose communication with the computer. The power LED will return to solid green status after a few minutes but I am not able to do much with NI DAQ to test the system since it has failed self test. The suspicion here is the power supply may be bad but how do we check that.
The system with the computer has worked well over the past several years and we are concerned about possible damage from a power fluctuation that happened here around Christmas time.

Hi Xavier,
The red flashing light is on the PXI 8360. I have not seen any flashing lights on the chassis.
The modules present in the system are
PXI 8360 MXI Express
PXI 4071 7 1/2 digit flex DMM
PXI 4110 Programmable DC power supply
PXI 4110
PXI 4110
PXI 8252 1394 Host Adapter
TB 2627 multiplexer terminal block
PXI 6289 M series multifunction DAQ
SCXI 1306
SCXI 1303
SCXI 1303
SCXI 1300
So far all testing has been done with all modules installed. Another person has tried reseating all modules to see if that would fix the problem but it does not.
The system will work fine for a few hours and then the blinking LED will begin and somewhere near that time the communications fail with the computer. The light will blink for a few minutes and then will return to solid green. Once the error has occurred it seems that the only way to re establish proper operation is to shut down the whole system, PXI chassis and computer, and restart. I saw one time where the power LED on the 8360 went from flashing red to solid green when the computer was turned off.
The computer is a Dell Precision 690 with PCIe 8361.
I will be opening up the chassis hopefully in the next day or two to check fuses and voltages where I can.
Bill

PXI Chassis Power LED Flashing Red: What to do?

My NI PXI-1042 keeps blinking red the Power LED. I know it means the voltage is out of the specs. What to do?

FilipeTaveiros wrote:
But it is not continuously red.. It is blinking red.. Thanks for your help. Anyone?
This is copied right out of the manual:
The chassis power switch has an integrated LED. This LED indicates one
of three different conditions:
• If the power switch LED is steady green (not flashing), the chassis is
powered on and operating normally.
• If the power switch LED is flashing green, the air-intake temperature
has exceeded the chassis operating range.
• If the power switch LED is flashing red, the power supply outputs are
not within voltage regulation requirements.
You either have a power supply problem, or you are loading it down with too many modules. Try running it empty and see what the light does.
Using LabVIEW: 7.1.1, 8.5.1 & 2013

Blank screen in Flash 8 Video Encoder with DivX

When using the Flash 8 video encoder to encode a DivX file, I
get a blank screen. No problem with the wmv files I've tried. this
is on two freshly purchased HP Windows Media Center XP PCs. Have
not had the same issue with our older Dell PCs, also XP(Pro not
Media Center). I have re-installed Flash 8 and the Divx codecs but
still have the issue.
Any ideas?
-JRParker

Ferrohead wrote:
> Thanks for the reply.
> I haven't tried this option yet, I've opened the Picture
Motion Browser but I don't see how to convert it to mpeg2.
>
> Can you tell me how to do this?
>
> Thanks again.
I have this option from right click menu - Convert to Mpeg 2
and save.
By the way, does your CD comes with Sony Vega program?
This one is able to open Sony's raw file format and export to
very nice
quality mpeg that works superb in flash. I did lots of video
using Vega,
to adjust the sharpness, color contrasts and all, before
start exporting and
down sizing...
Best Regards
Urami
"Never play Leap-Frog with a Unicorn."
<urami>
If you want to mail me - DO NOT LAUGH AT MY ADDRESS
</urami>

Blank screen with flash forms

I am attempting to get flash forms to work, but keep getting
a blank screen. Nothing is ever rendered to the screen. There is
also a message that pops up that states "Press SPACEBAR or ENTER to
activate and use this control". My code is below...
<cfform name="frmTest" format="flash" height="100%"
skin="haloblue">
<cfformgroup type="tabnavigator">
<cfformgroup type="page" label="Help 1">
<cfformitem type="text" style="font-weight:bold;
font-size:large;">
Help!
</cfformitem>
</cfformgroup>
<cfformgroup type="page" label="Help 2">
<cfformitem type="html" style="font-weight:bold;
font-size:large;">
Help!
</cfformitem>
</cfformgroup>
</cfformgroup>
</cfform>
We are using MX 7 and I have Flash 8 player installed.
Any Ideas?

Hi,
Please read the following to know more about the message that
appears in
Microsoft IE. It also shows you how to fix it, but I believe
it does not
work for the Flash movies created using ColdFusion tags.
http://www.adobe.com/devnet/activecontent/articles/devletter.html
Post here, if you figure out how to implement it for CFFORM
tags in
ColdFusion that produce flash SWFs.
Hope this helps.
- Milind Joshi
smaccurdy wrote:
> I am attempting to get flash forms to work, but keep
getting a blank screen.
> Nothing is ever rendered to the screen. There is also a
message that pops up
> that states "Press SPACEBAR or ENTER to activate and use
this control". My
> code is below...
>
>
> <cfform name="frmTest" format="flash" height="100%"
skin="haloblue">
> <cfformgroup type="tabnavigator">
> <cfformgroup type="page" label="Help 1">
> <cfformitem type="text" style="font-weight:bold;
font-size:large;">
> Help!
> </cfformitem>
> </cfformgroup>
> <cfformgroup type="page" label="Help 2">
> <cfformitem type="html" style="font-weight:bold;
font-size:large;">
> Help!
> </cfformitem>
> </cfformgroup>
> </cfformgroup>
> </cfform>
>
> We are using MX 7 and I have Flash 8 player installed.
>
> Any Ideas?
>

Blank screen with flashing folder with question mark on startup of 13" macbook

Hello world, my daughter's 13" macbook upon startup opens to a blank screen with a flashing folder with a question mark in it... If anyone could help us resolve this issue we would greatly appreciate it... Thanks!..

That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the Operating System data on the hard drive is somehow corrupted.
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Just press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
If it is then select the First Aid Tab and run Repair Disk. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.
If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

LED flashing red.

Hey, i have the blackberry pearl and i just recieved it from a friend. I was doing something with my desktop manager and all of a sudden my phone shut off and then i took the battery out unplugged my phone and tried repowering it but it wouldn't do anything. Now it's sitting on my charger with no battery but is still flashing red. What can i do to fix this?

Welcme to the Frums
http://supportforums.blackberry.com/rim/board/message?board.id=Bold&thread.id=8100
Nurse-Berry
Follow NurseBerry08 on Twitter

After installing updates my atv2 screen goes blank and led flashes rapidly

I just bought my atv2 and it told me to update, which I did, and then my screen went black and the led light started blinking rapidly. This is the second one in 2 days. I have tried disconnecting the hdmi, power, and holding down the arrow keys to reboot and still nothing.

numbfant wrote:
I recently got this ipod from the Apple store because my previous one broke. They gave me the ipod and right when I plugged it in, the screen turned an offwhite color, made a quiet buzzing sound and flashed. After a week of this it mysteriously started working so I didn't put much thought into it, I was just happy my iPod worked. Then after a month or two, it randomly started doing the same thing. No matter if I plug it in or not, the screen flashes a blank off white page.
It is also possible that your iPod has entered one of its "Sleep" modes. When it hasn't been used in a while, it goes through a couple of stages of this to preserve the battery's charge.
Try pressing the iPod's center button to wake it from sleep.
If this fails, start with a reset of the iPod (hold Menu & center buttons) and work your way through the rest of the 5 R's.
Steve

915G combo blank screen & LED indicator show 3 red & 1 green..

Hello every1..
HelP me!!!!!!!
my 915G combo show nothing on my monitor when i turn on. All the CPU & fun are running but show nothing on monitor. LED indicator show red for 3 pin and only a top right corner of pin show green signal. What could i do ?
what does the meaning of 4 LED indicator ? Please help me.
here is my system configuration..
MSI 915G combo Motherboard
LGA 775 , 3.2GHz Intel CPU 540
256*2 MB of DDR400 RAM
200GB Seagate 7200.9 SATA
LG GSA4160B DVD writer
Philips 17" LCD screen

Quote from: devilangel on 20-November-06, 17:22:17
thank you, BOSSKILLER, tonite , i will try
and 1 more question , why my computer always got this problem ,
it happened twice a years,
WHY ah, izzit this board not good enough.
Anyways , thousand thank you again for you help BossKiller.
you are welcome mate.
well suggest you to read Moan Guide and to explain better what problem you got in a new thread. keep us updated.

Z10 - blank screen + led flashing red

Similar Messages

Maybe you are looking for