Z10 doesn't restart and red light blinking only.

Hi,
My z10 phone was normally working, and sometimes it's don't response and hang. last time i tried to restart and it's took long time and i used blackberry link and did software update. in between software update was completed but it was not run. i got problem. Red light blinking.
even i charge it or restart, Red light blinking.
after i face this problem, i tried to slove by autoloader, new BB link and many more action done. Nothing work.
it might be mother board problem???? but i am not technician.
We cann't buy easily motherboard also.
I think Blackberry is totally **bleep**.... Since i have used blackberry storm , storm 9860 and z10 al are **bleep**.

I think BlackBerry is totally awesome...Since I have used BlackBerry Pearl, Curve, Bold, Z10, Q10, and now Z30. All are awesome.
There are so many things that could cause your Z10 to fail. You could have gotten it wet, dropped it, stepped on it, or any other manner of abuse. It could also have just failed on it's own through no fault of your own. Since I know MANY people with BB10 devices right now, including 3 in my own household and another 3 assigned to some coworkers there is no problem with all BlackBerrys.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

Similar Messages

8900 - Won't Power on. Red Light blinks only! Please help!

I have a Blackberry 8900 and this thing is driving me crazy!
To start, I woke up one morning and had a white scrreen and an error 502. I wasn't able to fix the issue immediately since I had class. I'm usually more attentive to my phone but I'm in law school. Anway, the next day I went to try to fix my phone, it would not power on at all. I just got the red light flash. When plugging it in to my computer, I got the sound it was connected but the AppLoader, JML_Cmder and DTM would not recognize the device. Frustrated, I put the phone aside again to concentrate on school.
So, I've decided to give this another shot but now it's gotten worse. The phone does nothing unless it's plugged up and it's still just that annoying red light blinking. I keep the phone plugged and remove the battery...still that blinking and the pattern is long pause, blink, short pause, blink, blink, blink repeat. Again, there is NO ACTIVITY when the phone is unplugged. Same thing when I plug it into my computer. The battery does not make a difference and doing a battery pull does not work. My computer does not recognize my device at all (no sounds, no connection, etc). I have tried to let it charge from a wall charger and it did nothing but that blink pattern for 12 hours.
Is there anything else I can do? It's an AT&T phone I purchased and use with T-mobile and both companies are being asses. Any last suggestions before I buckle and just throw the **bleep** thing away.
Again, I have tried the AppLoader through c:\program files\common files\research in motion\app loader, I have tried using the Command Prompt, I have tried JML_Cmder, I have tried the battery pull, I have re-installed both the DTM and the Blackberry USB and Modem drivers...
Anything else I could possibly try? Also, does anyone know what that blink pattern means?
And please don't suggest what I've listed already. Thanks!

Just to make sure you haven't missed a step, when you tried the Loader.exe file, did you try the steps to fix a nuked BlackBerry? The trick here is to remove the battery on the device, open the Loader.exe file, go to the second screen, then plug your phone in without the battery. As soon as your computer recognizes the phone, click next. This should be able to catch the JVM and allow access to reload the OS. Then once you get to the next screen, you can reinsert the battery.
If you have already tried that, then see if you can ensure that the battery is charged in another BlackBerry, or see if you can try another battery.
If none of that works, then let me know as there are still some other things we can come up with.
If you want to thank someone for their comment, do so by clicking the Thumbs Up icon.
If your issue is resolved, don't forget to click the Solution button on the resolution!

Z30 - doesn't re-starts - RED LIGHT BLINKS

i cant restart the bb z30, i was connected with charger also for four hours but no use, and pressed power button for 10 sec but it didnt started. how to solve this issue please help me

Recommendation:
Install BlackBerry Link on the Pc/Mac you own. Sign in to BlackBerry ID at the top of the app. Do 1 partial (settings no media) and then 1 full backup.
If you've been able to get that far use Link to see if there are any updates. Ensure you're directly connected to the computer not a hub.
Power off fully or press both volume buttons together for 10 seconds - I think that is the reset combination.

Z10 Red Light blink in 10111011, PC wont detect

Hi. The Z10 get stuck while i was using autoloader from blackberry developer site and never wake up again. The z10 is STL 100 -1.The telephone doesnt turn on, the screen is off, sometimes the red Light blink in 10111011. The PC doesnt recognize it. BB link doesnt too, update from the website too, and bootrom doesnt too. The cellphone doesnt charge, the battery is good (i try it in another z10 and was on 60% charge during the problem). Some solution?? thnx

Hi and Welcome to the Community!promiscuo wrote:
i was using autoloader from blackberry developer siteI have to guess that to be the root of the problem. Those OS packages are (typically) intentionally crippled, with various things left out of them or otherwise intentionally damaged for the development purpose. They are never intended for normal operations, and never for normal users. I recommend you reload an official OS, first try via LINK and if that fails obtain a proper user-level AutoLoader to install a proper OS to your device. Good luck and let us know!

Torch 9800 wont turn on and the red light blinking..

hi..im new at here..ive got problem with my bb torch 9800..last day after charging my phone..it cant turn on and the red light blinking..ive tried connect my phone to computer but it cant recognize my devise..ive tried many way to solve it like using BBSAK but it still cant connect to my devise..id tried using blackberry devise manager software but the problem still exist..really2 need ur help now..
*ive update my phone OS to the latest one..didnt know if that is the problem..need ASAP..

Hi and Welcome to the Community!
I am very confused by your post. You say you can't connect your device...to your computer? If so, how did you manage to upgrade the BB OS? Given that, from what you've described, you can use BBSAK, that would require connecting to your computer, but then you say you can't. So I'm confused.
Please try posting again, and be 100% clear about exactly what the symptom is that you wish to resolve, exactly all of the steps you have attempted (e.g., "like using BBSAK" isn't enough...what, exactly, did you do with BBASK?), and exactly the results of each step of what you have attempted.
Thanks and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I am using apple iPod-suffle model and I am unable to upload music into iPod and 3 lights(green,orange and red) keeps blinking for few seconds when I connect my iPod to my PC and after few seconds its turn to unresponce mode,Plz help to find out solution

I am using apple iPod-suffle model,I am unable to upload music into iPod and 3 lights(green,orange and red) keeps blinking for few seconds when I connect my iPod to my PC and after few seconds its turn to unresponce mode,Plz help to find out solution.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

Red light blinks and phone dosen't get on

firstly my os crashed and faded away and the display turns black.then i reinstalled the o.s 10.3 and now red light blinks and the phone dosen't get on!!

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs. If it fails, please try again but increase the wait time in step 4 to 2 hours, and perhaps as long as 4-5 hours.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
If it still continues to fail, then a forceful OS reload (via AutoLoader) would be my next recommended step.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Pearl 8100-Rogers not turning on-Red light blinking

Hello
I have new Blackberry Perl 8100.I got this from Rogers.It was sitting in box for few month.I tried turning on but it is not turning on.I left the phone in charge for more then 2 hour and it is still not turning on.
I tried taking out battery but and replacing back in but stillit is not turning on.I can only see red light blinking.nothing else.pls help me .thank you.

Leave the device to charge 2-3 hours, and then, still connected to the USB cable, remove the the battery from the device a few seconds and reinsert it. If it boots--leave it to charge to 100% (check Options > Status for the percentage).
If it doesn't boot--try using a wall outlet charger if you are not. If you are connected via USB to the PC, make certain that you have Desktop Manager (or the USB device drivers) installed, which you can download below.
Make certain your USB cable is connected to one of the PC's main rear USB ports. Not a USB hub, nor a monitor USB port, nor a USB port on the front of the PC.
Download Desktop Manager from here:
https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Blackberry Curve 9220 Won't Switch stuck On only red light blinking RED LIGHT! HELP!

my blackberry is stuck on red light blinking oleas help me no problem if all the data is lost i dont care i want my phone back it hase been 3 -4 weeks . light is blinking until the battery goes down and it wont charge also i have to get the battery charged by other phone plzz help mee........

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

I have an apple tv and the light blinks continuously after an electrical outage. does this mean my apple tv has been permanently damaged or only resetting is necessary?

I have an apple tv and the light blinks rapidly and continuously after a power outage. does this mean my apple tv has been permanently damaged?

Hello there, Philip.
For understanding the status light on the Apple TV, the following Knowledge Base article offers up some great information on what they mean:
Apple TV: About the status light - Apple Support
Apple TV (2nd and 3rd generation)
Status light
Apple TV (2nd and 3rd generation) is:
Flashes quickly
Having issues. Try restarting or waking your Apple TV. If your Apple TV does not start up properly, you might need to reset the Apple TV or restore it to factory settings. See Apple TV (2nd and 3rd generation): Restoring your Apple TV. If this does not resolve the issue, refer to the Service FAQ for additional assistance.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Torch Help! Screen not turing on but buttons and red light is flashing

Hi,
My torch has had the problem of screen functioning, it is just a black screen but buttons light up and led flashes red.
Thanks

I have tried this, blackberry works find but nothing id displayed on screen, just blackness. red light blinks and buttons are lighted up a if it is on.

Ix2 red light blinking after RAID 1 to RAID 0

Just bought a brand new Ix2 Lenovo unit. Quick start setup was easy, and I was able to connect to the unit. When trying to change disks to RAID 1 to RAID 0 through webpage configurator, it asked me to erase all data. I selected OK, since there was no data inside.
When building RAID after reboot, it goes to red light blinking. I have tried using manual reset button, but after few minutes with light blinking white, it goes to red again.
What did I do wrong?? Can you please help? It is a shame since I didnt have the unit for 24hrs.
Thanks
Solved!
Go to Solution.

Hello Pemba21
If the unit has not passed the flashing white boot process, then there is something stalling the unit.
Did you run a factory reset from the web interface or from the rear pin-hole reset?
I recommend swapping the internal disks to opposite bays while the unit is powered off then try booting again. It should only take about 5 minutes.
To access the disks, pull up on the faceplate and to unlatch it from the chassis, then pull the faceplate away from the chassis. The disks will have a plastic tray that locks them in place.
If that does not seem to help, I recommend contacting LenovoEMC support to create an incident.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

Been using an Avastor HDX-800 for storage and backup, also a SUPERDISK for smaller stuff; recently the SUPERDISK does not appear on the screen, and the light blinks while you hear it spin, also the Avastor has started to have the same problem, both USB

Been using an Avastor HDX-800 for storage and backup, also a SUPERDISK for smaller stuff; recently the SUPERDISK does not appear on the screen, and the light blinks while you hear it spin, also the Avastor has started to have the same problem, both USB conncected, both worked well before, but both now spinning, blinking, and not showing up on the screen as before,
Interestingly they both appear in the System Profiler, but just not working the same as before
I have tried other USB ports, but the same responce,

yes I did reset the PRAM, but no benefit, still the same problem
my usb devices are: keyboard, mouse, printer, SD-USB-M3, and LaCie d2 DVDRW:
the mouse and printed are plugged into the keyboard: i have tried to move, these around, and have even tried just the mouse, printer and SD-USB-M3, but still the same problem
here is a cut and paste of the current "System Profiler>Hardware>USB"   (usb device tree)
USB Bus:
Host Controller Location:          Built In USB
Host Controller Driver:          AppleUSBOHCI
PCI Device ID:          0x0026
PCI Revision ID:          0x0000
PCI Vendor ID:          0x106b
Bus Number:          0x18
Hub in Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x1002
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
SuperDisk USB 120MB drive:
Version:          0.0e
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Imation
Product ID:          0x0002
Vendor ID:          0x0718
Hub in Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x1002
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
HL-1270N series:
Version:          1.00
Bus Power (mA):          100
Speed:          Up to 12 Mb/sec
Manufacturer:          Brother
Product ID:          0x0008
Serial Number:          L9J286292
Vendor ID:          0x04f9
Basic Optical Mouse:
Version:          0.00
Bus Power (mA):          100
Speed:          Up to 1.5 Mb/sec
Manufacturer:          Microsoft
Product ID:          0x0084
Vendor ID:          0x045e
Apple Pro Keyboard:
Version:          1.22
Bus Power (mA):          250
Speed:          Up to 12 Mb/sec
Manufacturer:          Mitsumi Electric
Product ID:          0x0204
Vendor ID:          0x05ac (Apple Computer, Inc.)
SuperDisk USB 120MB drive:
Version:          0.0e
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          Imation
Product ID:          0x0002
Vendor ID:          0x0718
USB Bus:
Host Controller Location:          Built In USB
Host Controller Driver:          AppleUSBOHCI
PCI Device ID:          0x0026
PCI Revision ID:          0x0000
PCI Vendor ID:          0x106b
Bus Number:          0x19
LaCie d2 DVDRW USB:
Capacity:          451.76 MB
Removable Media:          Yes
Detachable Drive:          Yes
BSD Name:          disk2
Version:          0.00
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          LaCie
OS9 Drivers:          No
Product ID:          0x1011
Serial Number:          FFFFFFFFFFFF
S.M.A.R.T. status:          Not Supported
Vendor ID:          0x059f
LaCie d2 DVDRW USB:
Capacity:          451.76 MB
Removable Media:          Yes
Detachable Drive:          Yes
BSD Name:          disk2
Version:          0.00
Bus Power (mA):          500
Speed:          Up to 12 Mb/sec
Manufacturer:          LaCie
OS9 Drivers:          No
Product ID:          0x1011
Serial Number:          FFFFFFFFFFFF
S.M.A.R.T. status:          Not Supported
Vendor ID:          0x059f

Home screen is completely frozen on my Apple TV. I tried to reset and the light blinks but nothing happens after that. Any suggestions?

I tried to reset and the light blinks but nothing happens after that. It won't allow me to move the cursor on the home screen. Any suggestions?

Unplug the device from power and plug it back in.
If it still fails to respond properly, connect it to a computer via microUSB and restore via iTunes.

Desktop Computer dc5750 shuts down and red light flashes on front of computer and won't start at all

I have a DC5750 HP Compaq Computer it is 6 years old, but I have 4GB Ram, Nvidia GS8400 Graphics Card, two one TB Hard Drives. While I tried to re-installed my operating systems it all of a sudden shut down not once but twice, I opened up the side of the computer and found that it was hotter then normal. I let it sit for a while thinking it maybe over heating after hooking it back up I turned it on again nothing happened except a beeping noise and red lights flashing on the front. Can this be fixed as money is an issue.
Thanks
Rob

Hi, Rob:
Please review Appendix A. starting on page 56 of the Troubleshooting Guide at the link below to interpret the beep codes and see the probable causes and recommended troubleshooting steps.
http://h20566.www2.hp.com/portal/site/hpsc/template.BINARYPORTLET/public/kb/docDisplay/resource.proc...

Z10 doesn't restart and red light blinking only.

Similar Messages

Maybe you are looking for