Z30 stuck at 100 % boot

Hi guys,
so, strange thing: My Z30 ran out of battery yesterday, I recharged it this morning, it started to reboot but is now stuck at 100 Percent for at least 3 hours. I tried a soft-reset (Power and Volume Up/Down) but it just reboots to a 100 percent and stays there.
Has anyone any idea what to do (preferably without destroying the data, i have some 2 Factor Auth settings on there, that I kind of need...)
Regards
Solved!
Go to Solution.

There is the possibility of using an autoloader file to reload the OS, and doing so will wipe all current data from the z30.
http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Similar Messages

  • Z10 stuck at almost 100% boot up

    Please help. been using this phone for a while, even used it yesterday. now it won't switch on. please help. it's stuck in almost 100% boot up. how do i add a snapshot of phone in present state

    The progress Bar appears when your Boot Volume will not mount. It runs fsck and shows the progress bar to try and fix that. It never gets all they way across because the last few items take so little time. If the drive still will not mount at the end of the check, your Mac cannot proceed, so it shuts down.
    It appears, based on your description, that your Hard Drive has Errors late in the checking process, and hangs instead.
    You may need a new Drive.
    You can try a Re-Install-in-place, which will re-write a lot of blocks and may clear up the problem.
    If you do not have a Trusted Backup, do not do anything else until you have one.

  • PCM stuck at 100% when using any audio program for the first time

    I've had this issue for some months now after an update and couldn't find any solution anywhere so help would be appreciated.
    First time I run an audio program after boot PCM gets stuck at 100% and can't be decreased. Also, i3status's PCM info switches from 77% to 850%. No idea if the previous is useful. The problem disappears once that program is closed and PCM is changeable again. I'm using alsa and the chip is Conexant CX20551 (Waikiki), the issue persists even if I add the user to the audio group.
    Last edited by Minato (2013-07-14 11:34:10)

    I replaced the symlink with a folder named "Pictures" and it actually worked. At least a new menu shows up. BTW Photoshop Elements does not complain.

  • Disk Usage stuck at 100%, Factory installed windows 8 running like a turtle not being able to use my laptop. What should i do?

    I have a HP Pavillion Sleekbook 15-b002ee with Third generation core i5 processor 1.7 GHz, 500 GB Hard disk and 4 GB of RAM installed. Windows 8 came pre installed on it.
    I bought this laptop 11 months ago and it worked fine for 10 months and then from the last month its presenting unusual problems. My disk usage is stuck at 100% and the laptop freezes and never lets me work or do anything. Heres what i have already done
    to solve the issue but have been unsuccessful:
    1) I have reset my PC completely and reinstalled windows 8 using the factory setup. Didnt solve the issue, newly installed windows displays the disk usage 100% and the performance is same i.e the system freezes.
    2) I have tried adjusting my paging file, no change made a difference to the performance of my laptop. The default system managed Paging file size is something around 3.89 Gb. Does my problem have anything to do with my paging file?
    3) I have tried solving this issue by disabling the "Windows Search" and "Superfetch" services and still it didnt solve the problem.
    4) I have also run checkdisk on my hard drive completely. It took me a complete day to do so but still no change.
    5) Before resetting my laptop, an error called "Kernel_data_inpage(http.sys)" used to come on my upgraded windows 8.1. Whats the issue?
    So what should i do? Is there any problem with my hardware? Is my hard drive having bad sectors and is that causing the problem? Or is there any other technical problem which i couldnt yet find out?
    I have explained my problem in a lot detail and i would like a clear answer please, i have been at this issue for many days and this forum seems like the last place where i can find relevant answer because Google isnt helping.
    Thanks in advance.

    Ask here: http://h30434.www3.hp.com/. 
    This web site is for help in writing software and you are not planing in doing that. In the future, look around to see what others are saying before posting to a forum. If you can not understand what others are saying most likely you are in the wrong
    forum, and chances. are your questions will be ignored .
    If you are looking for help on a particular Microsoft product, start your search from support.microsoft.com instead of going to a random Microsoft forum. But since you got a HP laptop, chances are you have software prompted by HP as well, like antivirus/printer
    applications etc, so better ask HP first.
    Visual C++ MVP

  • Macbook pro 17" 3g battery status indicator stuck on 100%

    Battery status indicator stuck on 100% Worked normaly until today
    resetting smc does not help
    Battery Information:
      Model Information:
      Serial Number:          9G95201YS4M0A
      Manufacturer:          DP
      Device name:          bq20z951
      Pack Lot Code:          0000
      PCB Lot Code:          0000
      Firmware Version:          0042
      Hardware Revision:          0001
      Cell Revision:          0119
      Charge Information:
      Charge remaining (mAh):          65262
      Fully charged:          Yes
      Charging:          No
      Full charge capacity (mAh):          65262
      Health Information:
      Cycle count:          221
      Condition:          Replace Now
      Battery Installed:          Yes
      Amperage (mA):          -1629
      Voltage (mV):          8072

    I closed the lid for about 10 minutes to do something and when I came back the status seemed to be working correctly (80%) and the health now seems normal. I made no other changes. I will keep an eye on it and post if it goes haywire again. Thanks for your help
    Battery Information:
      Model Information:
      Serial Number:          9G95201YS4M0A
      Manufacturer:          DP
      Device name:          bq20z951
      Pack Lot Code:          0000
      PCB Lot Code:          0000
      Firmware Version:          0042
      Hardware Revision:          0001
      Cell Revision:          0119
      Charge Information:
      Charge remaining (mAh):          9833
      Fully charged:          No
      Charging:          No
      Full charge capacity (mAh):          12217
      Health Information:
      Cycle count:          221
      Condition:          Normal
      Battery Installed:          Yes
      Amperage (mA):          -1550
      Voltage (mV):          7930

  • IPhone 4s battery stuck at 100 percent. How do I get it back to normal?

    iPhone 4s battery stuck at 100 percent. How do I get it back to normal?
    Ever since the update, I am having issues with the battery. Phone shuts down while it still shows 100 percent battery life. Normally not a big deal because I don't use it all the time but lately an issue when I'm working in Manhattan and it shuts down while in the middle of conversation or emailing.
    I can't go around charging it every hour wondering what my battery life really is.
    Please help!

    My phone now is not working at all. It only works for a few minutes while it is plugged into the wall and then it shuts down and pops right back up showing it has 75% battery. It has been doing this since yesteday afternoon.
    I tried the reset and it is still acting up. Dreading having to take this to the Apple store since it is past the initial 90 days and I will probably get charged for it. :( Dont want to shell out money for a new one since I just got this one in October.
    Thanks for your help.

  • My phone is stuck on the boot

    my phone is stuck on the boot droid restarting itself when i try to turn it off it just restarts and sticks back on spinning red thing getting hot cant shut it off kept doing this until battery died

        Oh goodness! That is not the state of mind that we want your phone to be in. I'm guessing you have already spoken with someone at a store or by phone by now. In case this happens in the future, you should reset the phone  http://vz.to/1mdD3RJ.
    TamaraH_VZW
    Follow us on Twitter @VZWSupport

  • Disk Utility stuck on "updating boot support partitions for the volume as required"

    Tonight when I mounted my Time Machine drive (a WD My Passport drive), it failed to mount properly, and I received a warning from Drive Genius that it needed repair. But when I launched Drive Genius, the disk would not show up.
    Through a series of mounts, unmounts, and sleeping the computer, I managed to get it to show up in Disk Utility, so I seleted "Time Machine Backups" under the main listing for the drive ("319.37GB WD My Passort..."), and clicked Repair.
    The detail window showed "Volume repair complete" almost immediately. But for almost four hours now, it's been stuck on "Updating boot support partitions for the volume as required."
    Meanwhile, Activity Monitor has been showing fsku_hfs taking 30%-85% of the CPU the whole time.
    Anyone have advice?

    Apparently not:
    Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files.
    But when I ran Disk Utility again this morning, not on the Time Machine Backup, but up the hierarcy on the level labeled "319.37GB WD My Passort...," I got...
    The volume Time Machine Backups appears to be OK.
    And now the drive seem to be OK.
    I think I'll still offload everything and reformat it.

  • Tried to upgrade the software...stuck on 100%

    I got the software alert, so followed through the steps to upgrade to OS10 on my Z10....and it said it had to restart.  Clicked Now...it restarted but then got stuck on the blackberry logo, saying 100% and would not leave.  I could not shut it off, so I removed the battery.  Started again and the same thing...stuck on 100%.
    What can I do??

    Okay....I left it sitting and after like half an hour it finally started properly.  Just give it time.

  • MSI 970 FAN PROBLEM (Fan 2 stuck at 100%)

    Hi
    I have a problem with my 970, when i start the pc the fanspeed is normal on both my 970. But when i wait approximately 5 min the fanspeed on Card 1 (fan2) ramps up to 100% even in idle. I have tried everything to ramp it down but it dosnt even show that its stuck at 100% (Msi afterburner etc). I have tried to set a fanspeed/automatic fanspeed with msi afterburner but nothing helps. I just got this problem and i have not had it before.
    Anyone else have this or have a solution?

    You mean like this?
    https://forum-en.msi.com/index.php?topic=183618.0
    https://forum-en.msi.com/index.php?topic=184740.0

  • My iPad mini is stuck at 100% battery life (HELP!)

    My ipad mini has been stuck on 100% battery life all day and when I unplug it, it dies shortly after. I have to keep it plugged it to use it but it gets annoying.
    Its been stuck on 100% and has not gone down yet !
    I have tried turning it off, rebooting it, I checked my settings to see if I have done anything wrong, but nothing is working!
    Any suggestions on what I should do to solve this problem?

    Suggestion 1:  Run the device completely dead - and then recharge it.
    Suggestion 2:  Restore the device to factory settings (backup first).
    Suggestion 3:  Apple Genius Bar or Contact Apple support for a diagnostic test.
    Make a Genius Bar Reservation (or cancel an existing reservation)
    http://www.apple.com/retail/geniusbar/
    Sign in using your Apple ID
    AppleCare US phone number: (800)-694-7466
    Contact Apple for support and service
    http://support.apple.com/kb/HE57

  • Macbook not booting up so I resorted to Disk Utility...it has been stuck on "updating boot support partitions for the volume as required"

    So my Macbook was not booting up so I resorted to using Disk Utility...it has been stuck on "updating boot support partitions for the volume as required" for over two days.
    Has anyone else had to wait this long? 
    I have read that I should leave it until I get another message but I saw this reply on another site....
    "Hi everybody, the message: “Updating boot support partitions for the volume as required.“ means: the Disk Utilities is telling you what it is doing: 'Disk Utilities': "(I'm) Updating boot support partitions for the volume as required (& I'm done with it)." So when you see this message, the DS (Disk Utilities) is done & you can close the application"...
    Any advice/tips would be greatly appreciated!

    Doesn't have to be another MacBook - any Mac with FireWire (400 or 800) will do. FW 400 to 800 adapters or adapter cables should be available from any computer store.
    Instructions for FWTDM -
    Disconnect all other FireWire devices from both computers before you use FireWire target disk mode. Do not connect any FireWire devices until after you have disconnected the two computers from each other or have stopped using target disk mode.
    To use FireWire target disk mode
        1.    Make sure that the target computer is turned off.
        2.    If you are using an Apple portable computer such as a PowerBook or MacBook as the target computer, plug in its AC power adapter.
        3.    Use a FireWire cable to connect the target computer to a host computer. The host computer can be powered on.
        4.    Start up the target computer and immediately press and hold down the T key until the FireWire icon appears. The hard disk of the target computer should become available to the host computer and will likely appear on desktop. (If the target computer is running Mac OS X v10.4 Tiger, you can also open System Preferences, choose Startup Disk, and click Target Disk Mode. Restart the computer and it will start up in Target Disk Mode.)
        5.    When you are finished copying files, locate the target computer's hard disk icon on the desktop of the host computer and drag it to the Trash or choose Eject (or Put Away) from the File menu.
        6.    Press the target computer's power button to turn it off.
        7.    Unplug the FireWire cable.
    (extract from http://support.apple.com/kb/HT1661)

  • S90 stuck at the boot screen

    My S90 is stuck at the boot screen. It shows the booth screen for hours now. If I switch the power button it will not swtich off the phone, but restart it again to the boot screen. What should I do with it? I considered that I could let it run out of battery, but I am not sure how much the phone can run on a simple booth screen with just the lenovo log on the screen. Also not sure if once I recharge it would not have the same problem. Any advice how to solve this?

    I have no idea how it got stuck at the boot screen (the one after powered by android). The phone was out of battery, I connected it to the charger, immediately turned it on, and it got stuck. Draining did not help so I tried to fully charge it. That did not help. It was stuck at the boot screen until 5am (local time) so I had to follow the other instructions. That got me to a menu that let me choose the language between English and Chinese. Then I could reboot the device, power it off, install updates (or something similar), or wipe up device. Reboot or Power still got me back to being stuck at the boot screen. Install updates did not work. So I had to wipe up the data. That gave me two options (a) fuse wipe up data and (b) fuse format data (or something similar). No idea what the difference is, or what that does, but I was worried I will loose all my photos stored on the phone. But since I had no choice I decided to press "fuse wipe up data". That seems to have factory reset the phone. It started normally and it appears as after a factory resent (all my own apps and settings are gone). I had to pick the language and agree with Lenovo license agreement, etc. However, for some reason, all my photos were still in the phone's gallery (why?), so I  am now copying them to the pc. So that's how far I got so far. Thanks for your very valuable help and advice. Let's see if I encounter any more issues with it or any other peculiarities. 

  • Apple tv 2 is stuck on apple boot screen

    My apple tv 2 is stuck on apple boot screen.  What do I need to do?

    Try pulling ALL the cables for a moment and trying again, if the problem remains try restoring it by connecting it to iTunes with a micro USB cable.

  • Volume level gets stuck at 100%, iPhone 3g

    iPhone 3g, running the latest 2.0.1.
    I just got the phone yesterday but twice now the volume has gotten stuck at 100%. The volume display reads full blocks and you can't change it with the volume controls or vibrate switch. Even if you go into the iPod section, and try to drag the volume slider down, it just slowly creeps back up to full. The only way to 'fix' this is a reboot.
    Has anyone else had this? Are there are any fixes?

    Hey [ shua ],
    Do you have a protective case on the iPhone? Try testing without it.
    Also, try restoring the iPhone. http://docs.info.apple.com/article.html?artnum=305744
    If the issue persists after restoring the iPhone may need hardware repair. Make a reservation to have a Mac Genius take a look at it or call AppleCare.
    http://www.apple.com/retail/geniusbar/
    U.S. iPhone technical support: 1-800-MY-IPHONE (1-800-694-7466)
    Jason

Maybe you are looking for