Z61m radio will not power on

I don't use wireless often but when I tried today i could not get the radio to power on.
The little light is on (blinks every 5 sec.) the icon has the red slash through it but when I go to Access Connection I can not turn the radio on. Same thing with Fn/F5. I have checked the driver and its up to date. Any ideas on what i screwed up?

go here:
http://forums.lenovo.com/lnv/board?board.id=Special_Interest_Utilities

Similar Messages

  • RAP Running flex+bridge back haul A radio will not turn on

    Hardware: WLC 5508 running latest Software Version 8.0.100.0
    AP Code : c1550-k9w8-xx.153-3.JA
    Description :Whilst running in flex+bridge mode and configured as a Root AP, the RAP back-haul A radio will not change to operationally UP.
    If the AP is changed to be configured as a MAP, the A radio back haul will go operationally UP.
    Debug of the AP below and screenshot of the WLC has been attached.
    flashfs[0]: 38 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10195456
    flashfs[0]: Bytes available: 21673472
    flashfs[0]: flashfs fsck took 17 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
    IOS Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 38 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10195456
    flashfs[0]: Bytes available: 21673472
    flashfs[0]: flashfs fsck took 5 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Boot CMD: 'boot  flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    Initializing flashfs...
    flashfs[2]: 38 files, 3 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31610880
    flashfs[2]: Bytes used: 10195456
    flashfs[2]: Bytes available: 21415424
    flashfs[2]: flashfs fsck took 6 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 5806080
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 5805056
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete....done Initializing flashfs.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Rate table has 336 entries (20 legacy/64 11n/252 11ac)
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1824P030
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from unknown reload cause - ptr to non-ascii bytes 0x17
    LWAPP image version 8.0.100.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: B0:00:B4:61:A2:20
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC18159782
    Top Assembly Part Number             : 800-38848-03
    Top Assembly Serial Number           : FTX1824P030
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552EU-N-K9  
    % Please define a domain-name first.
    Spanning Tree protocol for Bridge Group 1 has not been configured.
    Press RETURN to get started!
    *Mar  1 00:00:08.551: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:09.311: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
    *Mar  1 00:00:09.311: Registering HW DTLS
    *Mar  1 00:00:09.751: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:11.547: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:12.415: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:15.279: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:15.471: AP Mesh platform identified (backhaul config:0x2, access:0xF)
    *Mar  1 00:00:15.535: Starting Ethernet promiscuous mode
    *Mar  1 00:00:18.103: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    *Mar  1 00:00:18.103: %SNMP-5-COLDSTART: SNMP agent on host APb000.b461.a220 is undergoing a cold start
    *Mar  1 00:00:19.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:20.019: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
    *Mar  1 00:00:20.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:21.503: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:22.151: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:22.191: Starting Ethernet promiscuous mode
    *Mar  1 00:00:22.355: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:22.355: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:36.591: Currently running a Release Image
    *Mar  1 00:00:36.603: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:41.019: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:00:41.023: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:41.031: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    *Mar  1 00:00:41.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:42.115: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    Not in Bound state.
    *Mar  1 00:00:42.123: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:43.031: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:43.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:43.223: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:44.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:46.067: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.067: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:46.103: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.144, mask 255.255.255.192, hostname APb000.b461.a220
    *Mar  1 00:00:46.103: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.103: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:51.143: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:51.211: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
    Translating "CISCO-CAPWAP-CONTROLLER.bla"...domain server (10.207.15.11)
    *Mar  1 00:00:51.211: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 00:00:52.207: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.229 obtained through DHCP
    *Mar  1 00:00:52.207: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.230 obtained through DHCP
    *Mar  1 00:00:52.211: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:52.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:52.223: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:53.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:53.243: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:54.243: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Sep 16 02:13:35.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:13:37.055: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:13:37.055: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
    *Sep 16 02:13:37.839: %LWAPP-4-CLIENTEVENTLOG: 
    Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
    *Sep 16 02:13:38.951: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 16 02:13:39.875: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
    *Sep 16 02:13:40.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Sep 16 02:13:40.243: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
    *Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:13:40.287: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
    *Sep 16 02:13:41.895: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    Writing out the event log to flash:/event.log ...
    *Sep 16 02:20:51.675: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Recvd RESET req from Controller.
    *Sep 16 02:20:51.687: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
    Write of event.log done
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 36 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10009088
    flashfs[0]: Bytes available: 21859840
    flashfs[0]: flashfs fsck took 17 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
    IOS Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 36 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10009088
    flashfs[0]: Bytes available: 21859840
    flashfs[0]: flashfs fsck took 5 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Boot CMD: 'boot  flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    Initializing flashfs...
    flashfs[2]: 36 files, 3 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31610880
    flashfs[2]: Bytes used: 10009088
    flashfs[2]: Bytes available: 21601792
    flashfs[2]: flashfs fsck took 6 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 5806080
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 5805056
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete....done Initializing flashfs.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Rate table has 336 entries (20 legacy/64 11n/252 11ac)
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1824P030
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from unknown reload cause - ptr to non-ascii bytes 0x18
    LWAPP image version 8.0.100.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: B0:00:B4:61:A2:20
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC18159782
    Top Assembly Part Number             : 800-38848-03
    Top Assembly Serial Number           : FTX1824P030
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552EU-N-K9  
    % Please define a domain-name first.
    Spanning Tree protocol for Bridge Group 1 has not been configured.
    Press RETURN to get started!
    *Mar  1 00:00:08.551: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:09.311: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
    *Mar  1 00:00:09.311: Registering HW DTLS
    *Mar  1 00:00:09.747: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:11.547: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:12.411: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:12.423: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:15.279: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:15.455: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:15.467: AP Mesh platform identified (backhaul config:0x2, access:0xF)
    *Mar  1 00:00:15.535: Starting Ethernet promiscuous mode
    *Mar  1 00:00:18.087: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    *Mar  1 00:00:18.087: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
    *Mar  1 00:00:18.463: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:18.531: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:18.735: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:18.739: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:19.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:20.011: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
    *Mar  1 00:00:20.323: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:21.495: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:30.559: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.147, mask 255.255.255.192, hostname APb000.b461.a220
    *Mar  1 00:00:36.591: Currently running a Release Image
    *Mar  1 00:00:36.603: Using SHA-1 signed certificate for image signing validation.%Default route without gateway, if not a point-to-point interface, may impact performance
    *Mar  1 00:00:40.939: AP image integrity check PASSED
    *Mar  1 00:00:40.947: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
    *Mar  1 00:00:41.027: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:00:41.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:42.127: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:42.135: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:43.127: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:43.235: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:44.235: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    %Error opening flash:/capwap-saved-config (No such file or directory)
    *Mar  1 00:00:51.047: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    *Mar  1 00:00:51.055: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:51.059: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:51.059: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:56.099: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:56.115: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
    *Mar  1 00:00:56.115: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 00:00:57.115: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
    *Mar  1 00:00:59.831: Starting Ethernet promiscuous mode
    *Mar  1 00:00:59.839: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.229 obtained through DHCP
    *Mar  1 00:00:59.839: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.198.0.230 obtained through DHCP
    *Mar  1 00:03:15.031: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Mar  1 00:03:15.031: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Mar  1 00:03:15.031: %MESH-6-LINK_UPDOWN: Mesh station b000.b461.a23c link Down
    *Mar  1 00:03:34.151: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:03:39.191: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:06:04.151: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join timer expired
    *Mar  1 00:06:04.151: %MESH-3-TIMER_EXPIRED: Mesh Lwapp join failed expired
    *Mar  1 00:06:04.151: %MESH-6-LINK_UPDOWN: Mesh station b000.b461.a23c link Down
    *Mar  1 00:06:23.271: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:06:28.311: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 35 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10014208
    flashfs[0]: Bytes available: 21854720
    flashfs[0]: flashfs fsck took 17 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
    IOS Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 35 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10014208
    flashfs[0]: Bytes available: 21854720
    flashfs[0]: flashfs fsck took 5 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Boot CMD: 'boot  flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    Initializing flashfs...
    flashfs[2]: 35 files, 3 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31610880
    flashfs[2]: Bytes used: 10014208
    flashfs[2]: Bytes available: 21596672
    flashfs[2]: flashfs fsck took 6 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 5806080
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 5805056
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete....done Initializing flashfs.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Rate table has 336 entries (20 legacy/64 11n/252 11ac)
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1824P030
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from unknown reload cause - ptr to non-ascii bytes 0x17
    LWAPP image version 8.0.100.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: B0:00:B4:61:A2:20
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC18159782
    Top Assembly Part Number             : 800-38848-03
    Top Assembly Serial Number           : FTX1824P030
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552EU-N-K9  
    % Please define a domain-name first.
    Spanning Tree protocol for Bridge Group 1 has not been configured.
    Press RETURN to get started!
    *Mar  1 00:00:08.539: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:09.299: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
    *Mar  1 00:00:09.299: Registering HW DTLS
    *Mar  1 00:00:09.731: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:11.527: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:12.395: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:12.403: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:15.263: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:15.451: AP Mesh platform identified (backhaul config:0x2, access:0xF)
    *Mar  1 00:00:15.519: Starting Ethernet promiscuous mode
    *Mar  1 00:00:18.083: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    *Mar  1 00:00:18.083: %SNMP-5-COLDSTART: SNMP agent on host APb000.b461.a220 is undergoing a cold start
    *Mar  1 00:00:18.503: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:18.543: Starting Ethernet promiscuous mode
    *Mar  1 00:00:18.707: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:18.707: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:19.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:20.011: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
    *Mar  1 00:00:20.311: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:21.495: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:36.571: Currently running a Release Image
    *Mar  1 00:00:36.583: Using SHA-1 signed certificate for image signing validation.
    %Error opening flash:/capwap-saved-config (No such file or directory)
    *Mar  1 00:00:41.003: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    *Mar  1 00:00:41.011: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:00:41.015: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:42.107: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    Not in Bound state.
    *Mar  1 00:00:42.115: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:43.023: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:43.107: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:43.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:44.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:46.043: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.043: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:46.095: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.147, mask 255.255.255.192, hostname APb000.b461.a220
    *Mar  1 00:00:46.095: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.095: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:51.135: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:51.151: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
    *Mar  1 00:00:51.151: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 00:00:52.151: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
    *Mar  1 00:00:55.831: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.207.15.23 obtained through DHCP
    *Sep 16 02:30:49.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:30:49.559: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:30:49.559: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
    *Sep 16 02:30:50.759: %LWAPP-3-CLIENTERRORLOG: Load Reap Cfg failed, trying backup...
    *Sep 16 02:30:50.775: %LWAPP-4-CLIENTEVENTLOG: 
    Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
    *Sep 16 02:30:50.779: %LWAPP-4-CLIENTEVENTLOG: No REAP non-ap specific configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:30:52.215: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Sep 16 02:30:52.223: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Sep 16 02:30:52.651: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
    *Sep 16 02:30:52.691: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:30:52.695: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
    *Sep 16 02:30:53.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Sep 16 02:30:53.243: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Sep 16 02:30:53.867: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
    *Sep 16 02:30:53.867: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 16 02:30:54.127: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    *Sep 16 02:30:54.871: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Sep 16 02:30:55.895: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Sep 16 02:30:56.895: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to upRename from flash:/lwapp_reap.cfg to flash:/lwapp_reap.cfg.bak failed, errorno = 2
    *Sep 16 02:31:14.119: %CLEANAIR-6-STATE: Slot 1 disabled
    *Sep 16 02:38:12.379: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Sep 16 02:38:12.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Sep 16 02:38:13.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Sep 16 02:38:13.407: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Sep 16 02:38:14.387: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 16 02:38:15.339: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 2
    Writing out the event log to flash:/event.log ...
    *Sep 16 02:38:24.375: %SYS-5-RELOAD: Reload requested by CAPWAP CLIENT. Reload Reason: Recvd RESET req from Controller.
    *Sep 16 02:38:24.387: %LWAPP-5-CHANGED: CAPWAP changed state to DOWN
    Write of event.log done
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 39 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10195456
    flashfs[0]: Bytes available: 21673472
    flashfs[0]: flashfs fsck took 17 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA"...############
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-mx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
    IOS Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 39 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 10195456
    flashfs[0]: Bytes available: 21673472
    flashfs[0]: flashfs fsck took 5 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: b0:00:b4:61:a2:20
    Boot CMD: 'boot  flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA;flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA'
    Loading "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA"...################################
    File "flash:/c1550-k9w8-mx.153-3.JA/c1550-k9w8-xx.153-3.JA" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    Initializing flashfs...
    flashfs[2]: 39 files, 3 directories
    flashfs[2]: 0 orphaned files, 0 orphaned directories
    flashfs[2]: Total bytes: 31610880
    flashfs[2]: Bytes used: 10195456
    flashfs[2]: Bytes available: 21415424
    flashfs[2]: flashfs fsck took 6 seconds.
    flashfs[2]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 5806080
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 5805056
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete....done Initializing flashfs.
    Radio0  present 8364B 8000 A8020000 0 A8030000 30
    Rate table has 336 entries (20 legacy/64 11n/252 11ac)
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J2.bin
    Radio1  present 8364B 8000 B8020000 0 B8030000 13
    POWER TABLE FILENAME = flash:/c1550-k9w8-mx.153-3.JA/J5.bin
    Radio2 not present 0 0 0 0 0 11
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP1552EU-N-K9 (PowerPC 8349) processor (revision A0) with 98294K/32768K bytes of memory.
    Processor board ID FTX1824P030
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from unknown reload cause - ptr to non-ascii bytes 0x18
    LWAPP image version 8.0.100.0
    4 Gigabit Ethernet interfaces
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: B0:00:B4:61:A2:20
    Part Number                          : 73-13538-02
    PCA Assembly Number                  : 800-31224-01
    PCA Revision Number                  : 03
    PCB Serial Number                    : FOC18159782
    Top Assembly Part Number             : 800-38848-03
    Top Assembly Serial Number           : FTX1824P030
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-CAP1552EU-N-K9  
    % Please define a domain-name first.
    Spanning Tree protocol for Bridge Group 1 has not been configured.
    Press RETURN to get started!
    *Mar  1 00:00:08.563: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
    *Mar  1 00:00:09.323: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (1-6)
    *Mar  1 00:00:09.323: Registering HW DTLS
    *Mar  1 00:00:09.759: m8349_ether_enable: MACCFG1 sync timeout
    *Mar  1 00:00:11.559: %LINK-6-UPDOWN: Interface Ethernet4, changed state to up
    *Mar  1 00:00:12.423: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
    *Mar  1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet1, changed state to up
    *Mar  1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet2, changed state to up
    *Mar  1 00:00:12.435: %LINK-6-UPDOWN: Interface GigabitEthernet3, changed state to up
    *Mar  1 00:00:15.291: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
    *Mar  1 00:00:15.479: AP Mesh platform identified (backhaul config:0x2, access:0xF)
    *Mar  1 00:00:15.547: Starting Ethernet promiscuous mode
    *Mar  1 00:00:18.119: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1550 Software (C1520-K9W8-M), Version 15.3(3)JA, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2014 by Cisco Systems, Inc.
    Compiled Fri 15-Aug-14 13:50 by prod_rel_team
    *Mar  1 00:00:18.119: %SNMP-5-COLDSTART: SNMP agent on host RAP is undergoing a cold start
    *Mar  1 00:00:19.459: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 00:00:20.035: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
    *Mar  1 00:00:20.335: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet4, changed state to up
    *Mar  1 00:00:21.519: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:22.163: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:22.203: Starting Ethernet promiscuous mode
    *Mar  1 00:00:22.367: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Mar  1 00:00:22.367: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
    *Mar  1 00:00:36.603: Currently running a Release Image
    *Mar  1 00:00:36.615: Using SHA-1 signed certificate for image signing validation.
    *Mar  1 00:00:41.023: %MESH-6-ADJACENCY_STATE_MACHINE_STARTED: Mesh adjacency state machine started
    *Mar  1 00:00:41.027: Logging LWAPP message to 255.255.255.255.
    *Mar  1 00:00:41.035: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
    *Mar  1 00:00:41.043: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 00:00:42.119: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    Not in Bound state.
    *Mar  1 00:00:42.127: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:43.035: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:43.119: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Mar  1 00:00:43.227: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:44.227: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:46.051: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.051: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:46.107: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.199.119.149, mask 255.255.255.192, hostname RAP
    *Mar  1 00:00:46.107: %LWAPP-3-LWAPP_INTERFACE_GOT_IP_ADDRESS: Interface BVI1 obtained IP from DHCP...
    *Mar  1 00:00:46.107: %MESH-6-CAPWAP_RESTART: Mesh Capwap re-started
    *Mar  1 00:00:51.147: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Mar  1 00:00:51.211: %LWAPP-4-CLIENTEVENTLOG: Not sending change state post as the radio admin is down, lrad state = 5
    Translating "CISCO-CAPWAP-CONTROLLER."...domain server (10.207.15.11)
    *Mar  1 00:00:51.215: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Mar  1 00:00:52.211: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.207.15.23 obtained through DHCP
    *Mar  1 00:00:52.215: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 00:00:52.219: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:52.227: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 00:00:53.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 00:00:53.247: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 00:00:54.247: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Sep 16 02:40:24.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:40:24.555: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.207.15.23 peer_port: 5246
    *Sep 16 02:40:24.555: %CAPWAP-5-SENDJOIN: sending Join Request to 10.207.15.23
    *Sep 16 02:40:24.771: %LWAPP-4-CLIENTEVENTLOG: 
    Checksum required saved version = 8.0.100.0, file flash:/lwapp_reap.cfg
    *Sep 16 02:40:26.219: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Sep 16 02:40:26.227: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Sep 16 02:40:26.443: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Sep 16 02:40:26.595: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller XVD-WLC-5508-02
    *Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No LS Flex ACL map configuration file to load. Connect to controller to get configuration file
    *Sep 16 02:40:26.639: %LWAPP-4-CLIENTEVENTLOG: No Central Dhcp map configuration file to load. Connect to controller to get configuration filecapwap_delete_all_l2Acls_in_nacl_list:336. Deleting all L2Acls in AP config
    *Sep 16 02:40:27.219: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    Regards,
    Will

    Australia and the AP seems to be in the correct country. The Operational Status is "REG" on both AP's.

  • Radio will not enable

    I am running a 2106 controller with 1242 AP,
    Had them on a POE injector on the same switch worked fine, mounted them in the ceiling now the radio will not enable."error in enabling admin status". any ideas?

    Hi Paul,
    I think you might be running into this issue because the 1242 AP supports the Intelligent Power Management feature (which I didn't even know existed until recently). Have a look at the following.
    Power Issue with the AP
    When an AP uses a power injector as the power source, in some cases, the AP displays this error message:
    CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC inline
    This message indicates that the AP is in low-power mode with all radios disabled and detects a Cisco switch that is unable to supply sufficient power to the AP. Even though the power injector, which can provide sufficient power, is connected with the AP, the AP still displays a LOW POWER error message and disables the radios. Therefore, the AP remains in low-power mode.
    One possible reason for this issue might be that the AP supports the Intelligent Power Management feature. The Intelligent Power Management feature uses Cisco Discovery Protocol (CDP) to allow powered devices, such as an AP, to negotiate with a Cisco switch for sufficient power. The AP supports the Intelligent Power Management feature. As a result of the power negotiations, the AP either enters full-power mode or remains in low-power mode with the radios disabled.
    In this case, the AP might be connected to a switch which cannot provide the necessary power to the AP. Therefore, even though the power injector is connected to the AP that uses this Intelligent Power management feature, it gives priority to the CDP information to identify whether or not the switch can provide the power. Once the AP knows, via CDP message, that the switch does not provide sufficient power, it disables the radios and remains in low-power mode.
    The workaround to this issue is to tell the AP to ignore the CDP information for power. You can perform this by telnetting into the APs. Issue these commands to enable the APs to use the power injector:
    power inline negotiation prestandard source
    power inline negotiation injector H.H.H
    The power inline negotiation command configures the Cisco Aironet 1130AG or 1240AG Series AP to operate with a later version of switch software that does not support Cisco Intelligent Power Management power negotiations.
    The prestandard source portion of the command specifies that the Cisco switch runs a later version of software that does not support Intelligent Power Management negotiations, but is able to supply sufficient power to the AP.
    The injector H.H.H portion of the command specifies that a power injector supplies power to the AP, and that the AP connects to a new switch port with the indicated MAC address (H.H.H). Enter the MAC address (in xxxx.xxxx.xxxx hexadecimal format) of the new switch port where the power injector is connected.
    Note: This command should only be used when you move an AP and power injector to a different switch port.
    From this good doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps441/products_tech_note09186a00800a86d7.shtml#new3
    Hope this helps!
    Rob

  • My vintage Power Mac will not power on.  The power on button lights up, but dims after releasing the button.  What is the problem?

    My vintage Power Mac will not power on.  The power on button glows bright when pressed, but dims to off after releasing the button.  What is the problem?

    The battery is the PRAM battery:
    Your Mac stores certain settings in a special memory area even if it is turned off (unless there is a battery issue as described below).  On Intel-based Macs, this is stored in memory known as NVRAM; on PowerPC-based Macs, this is stored in memory known as PRAM. Information stored in NVRAM or PRAM may include:
    Speaker volume
    Screen resolution
    Startup disk selection
    You may need to reset the NVRAM or PRAM if you experience issues related to these functions. For example, if your Mac starts up from a startup disk other than the one you've specified in Startup Disk preferences, or if a "question mark" icon appears briefly when your Mac starts up, resetting NVRAM or PRAM may help.
    http://support.apple.com/kb/HT1895#
    Replace the battery and reset the PRAM.
    Resetting your Mac's PRAM and NVRAM - Support - Apple
    Can I purchase a replacement battery at Walmart?
    Likely not.
    Order one at OWC for the best price ($20+ at Radio Shack):
    NewerTech 3.6VPRAM 3.6v Lithium 1/2 AA PRAM... in stock at OWC
    But have not sure what a PSU is or how to test it.
    PSU- Power Supply Unit.
    Then the steps that I deswcribed may be a bit advanced for you?
    The PSU is the gray box at the top rear of the interior, the box to which the power cord is attached and has the fan blowing hot air out.

  • 1130AG Radio will not enable.

    Hey folks,
    Something happend over the weekend at a remote site with my 1130AG WAP.  The ethernet is up but the Radio will not come up.  Here are some logs, etc:
    000010: *Jun 14 10:46:43.010 CDT: %SSH-5-ENABLED: SSH 1.99 has been enabled
    000011: *Jun 14 10:46:43.013 CDT: Writing radio coredump to 'flash:/r0.rcore'
    000012: *Jun 14 10:46:43.811 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    000013: *Jun 14 10:46:44.210 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    000014: *Jun 14 10:46:51.388 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    000015: Jun 14 10:48:25.109 CDT: Writing radio coredump to 'flash:/r0.rcore'
    000016: Jun 14 10:48:26.306 CDT: Interface Dot11Radio0: not starting because stop-on-failure set
    000017: Jun 14 10:48:31.081 CDT: %PKI-6-AUTOSAVE: Running configuration saved to NVRAM
    000018: Jun 14 10:49:15.904 CDT: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source
    000019: Jun 14 10:49:15.904 CDT: Interface Dot11Radio0: not starting because stop-on-failure set
    Just so not to rabbit trail, line item 18 above is because I am using a POE injector (non Cisco) which IS 802.3af compliant. (http://www.engeniustech.com/resources/NPE-4818_PoE.pdf).  It's cheaper than purchasing a POE switch (Cisco or otherwise) for only one POE device in this remote office of two users. ($21)
    Hereis the #show interfaces Dot11Radio0
    Dot11Radio0 is initializing, line protocol is down
      Hardware is 802.11G Radio, address is 0000.0000.0000 (bia 0000.0000.0000)
      MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
         reliability 255/255, txload 1/255, rxload 1/255
      Encapsulation ARPA, loopback not set
      ARP type: ARPA, ARP Timeout 04:00:00
      Last input never, output never, output hang never
      Last clearing of "show interface" counters never
      Input queue: 0/1127/0/0 (size/max/drops/flushes); Total output drops: 0
      Queueing strategy: fifo
      Output queue: 0/30 (size/max)
      5 minute input rate 0 bits/sec, 0 packets/sec
      5 minute output rate 0 bits/sec, 0 packets/sec
         0 packets input, 0 bytes, 0 no buffer
         Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
         0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
         0 input packets with dribble condition detected
         0 packets output, 0 bytes, 0 underruns
         0 output errors, 0 collisions, 0 interface resets
         0 babbles, 0 late collision, 0 deferred
         0 lost carrier, 0 no carrier
         0 output buffer failures, 0 output buffers swapped out
    I see the Stop-On-Failure log line 19, but not having much luck determining how to trouble-shoot this.
    The unit connects back to a 3com switch (after going through the POE Injector).
      TAC tells me the warranty ran out last month (May), and I could either do one-time suppport @ $400/hr, or probably better off purchasing a new one.
    Before I purchase a new one, what might I be missing that could resolve this?
    Thanks,
    James

    Well, thanks for all the assistance.  The answers were correct so far.  I have awarded
    points for them.  The problem still seems to persist.  Here is the latest log files:
    000010: *Feb 28 19:00:23.250 EST: %SNMP-5-COLDSTART: SNMP agent on host ATL-AP-01 is undergoing a cold start
    000011: *Jun 15 08:33:26.008 CDT: %SSH-5-ENABLED: SSH 1.99 has been enabled
    000012: *Jun 15 08:33:26.504 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to down
    000013: *Jun 15 08:33:26.747 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    000014: *Jun 15 08:33:26.837 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    000015: *Jun 15 08:33:28.714 CDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up
    000016: Jun 15 08:36:11.745 CDT: %CDP_PD-4-POWER_OK: Full power - NON_CISCO-NO_CDP_RECEIVED inline power source
    000017: Jun 15 08:36:32.830 CDT: %DOT11-2-RESET_RADIO: Restarting Radio interface Dot11Radio0 due to won't start
    000018: Jun 15 08:36:34.825 CDT: %SYS-3-CPUHOG: Task is running for (1995)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2E6F68 0x2E2158 0x4F7BEC 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000019: Jun 15 08:36:36.820 CDT: %SYS-3-CPUHOG: Task is running for (3990)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2EB6E8 0x2E6F6C 0x2E2158 0x4F7C08 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000020: Jun 15 08:36:38.816 CDT: %SYS-3-CPUHOG: Task is running for (5985)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2E6FA8 0x2E6F7C 0x4F7C08 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000021: Jun 15 08:36:39.815 CDT: %SYS-3-CPUYLD: Task ran for (6984)msecs, more than (2000)msecs (0/0),process = Dot11 driver
    000022: Jun 15 08:43:20.284 CDT: %SYS-5-CONFIG_I: Configured from http by admin on 172.16.1.205
    000023: Jun 15 08:43:20.474 CDT: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    000024: Jun 15 08:43:45.135 CDT: %DOT11-2-RESET_RADIO: Restarting Radio interface Dot11Radio0 due to won't start
    000025: Jun 15 08:43:47.129 CDT: %SYS-3-CPUHOG: Task is running for (1994)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2E6F68 0x2E2158 0x4F7BEC 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000026: Jun 15 08:43:49.124 CDT: %SYS-3-CPUHOG: Task is running for (3989)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2EB6E8 0x2E6F6C 0x2E2158 0x4F7C08 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000027: Jun 15 08:43:51.120 CDT: %SYS-3-CPUHOG: Task is running for (5985)msecs, more than (2000)msecs (0/0),process = Dot11 driver.
    -Traceback= 0x2E6F68 0x2E2158 0x4F7C08 0x7D2070 0x7D4D8C 0x5034E0 0x50CA74 0x1A3B30
    000028: Jun 15 08:43:52.120 CDT: %SYS-3-CPUYLD: Task ran for (6984)msecs, more than (2000)msecs (0/0),process = Dot11 driver
    Any other ideas or, the radio probably dead?
    THanks,
    James

  • My Powerbook will not power up, but I can hear the fan running...

    Please help!! My Powerbook will not power up, but I can hear the fan running when I press the power button to attempt to power it up. I just received a new power adapter because it wasn't working properly and it was doing this before and then it worked for a week and now it will not power up at all. It just starts the fan but nothing else turns on. When I plug the adapter, with the battery still connected, it will look as if it is charging but then the light on the plug turns from green to orange then off and doesn't power up at all. If I take the battery out and plug in the adapter, the light stays on but it does not power up except for the fan noise. Does anyone have any suggestions? I also followed the two articles listed online in regards to resetting the power setting and the command + alt + P + R as well. Nothing works. Thanks in advance.....

    Same here. If I start up with the power adapter attached, it starts up fine. If I try to start up from battery only, the fan comes on, the sleep light comes on but nothing else happens. I tried letting it sit that way for about 15 minutes and nothing changed. I tried attaching the power cord while in this mode and nothing changed. I tried the PMU reset a couple of times but nothing helps.
    This computer is just over 1 year old and I have not had any problems with the power cord (3rd party), the battery, or any problem like this before. It started after a proper shutdown last night and attempt to start without the power cord this afternoon.
    Any answers to this yet? I think I'll call on this and report any success to this discussion.
    15" PowerBook G4   Mac OS X (10.4.8)   1 GB DDR2 SDRAM, 100 GB HD

  • Need Help HP DM3 (DM3-1130us) Laptop will not power on. No power at all except for light on a/c jack

    Hello, I need some help.
    I have a HP DM3-1130us Laptop that will not power on at all.
    the only thing that happens when I plug it in is the power jack lights up.
    When the power button is used absolutely nothing happens.
    No power, no fans, no leds, no on/off cycles, no beebs, absolutely nothing
    just the light by the power jack that says the cord is plugged in.
    The laptop has Windows 7, 320gb hdd, 4gb ram.
    I have tried new power adapter and still nothing.
    I have taken the battery out and tried and nothing.
    I've tried the option where you take the battery out and hold the power and nothing.
    I have tried with different hard drive and no hard drive and nothing.
    I have tried reseating the ram and tried new ram modules still nothing.
    So I am kind of stumped on what to do, the laptop will just not turn on.
    Its not under warranty anymore so cant send it off.
    It has not been exposed to any elements(extreme heat or water).
    and its never been dropped or anthing.
    Im kind of wondering maybe the power button board its self is bad?
    If feels fine, its not loose or anything but could it
    have just stopped working? for those who are not familiar with this model.
    the power button is on the side and is a kind of drag and release button.
    Its also on the same board with the Wifi button and 2 Usb ports.
    But Im wondering before I buy a new one if this is what it could be.
    Or could the motherboard its self be bad?
    But even if the motherboard is bad would it still power up
    just not post?
    Also does anyone know of any other way to try to power this laptop up
    without using the slide button. I mean kind of like off a Dv6000 you can power the laptop on by using the Quicklaunch buttons on top but this laptop does not have those.
    If anyone can provide any information I would appreciate it.
    Thank you.

    Hey Tyler,
    Unfortunately it is difficult to troubleshoot this type of issue. The majority of the time when the computer wont power on with the same symptoms you described, the power supply board is faulty. Most of the time if the motherboard is bad it should at least turn on or so some signs of life. Like I said, this is most of the time. Sometimes it could do exactly what your experiencing. I would suspect the power supply board has failed since you are not receiving any sort of lights, sounds, etc.
    You could check the motherboard for swollen capacitors or loose solder joints but sometimes you wont be able to find anything.
    I hope this helps answers your questions,
    Sean
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

  • I have a Sony radio in my car.   With IOS  4 on my IPhone I could use the docking plug to the usb input on the radio and stream ESPN radio or pandora to the radio.  After upgrading to IOS 5 on the phone the Sony radio will not recognize the phone .  Any t

    I have a Sony radio in my car.   With IOS  4 on my IPhone I could use the docking plug to the usb input on the radio and stream ESPN radio or pandora to the radio.  After upgrading to IOS 5 on the phone the Sony radio will not recognize the phone .  Any thoughts.

    I am reading on this site about the error I am getting and it wants me to change some files that I am not comfortable messing with. Mainly because it is like a foreign language. Will the store do this for me or tell me if it is neccessary?

  • My iPhone 5s will not power on and I need my serial number for support.

    I am attempting to get help through Apple Support- Chat, but I need my serial number.  It is not showing up in iTunes under the device preferences.  Any other ways to retrieve the serial number through iCloud?
    If anyone has any idea of what is going on with my phone, I would love some assistance.  I live 45 minutes from the nearest Apple Store.  Here's the situation:
    About 2 weeks ago, my phone started shutting itself off and restarting randomly.
    About a week and a half ago, I would randomly get a blue screen and then the phone would restart multiple times.
    About a week ago I turned off Touch ID in an effort to resolve the issue, after reading some fixes from this community.  That seemed to help.  I do have the animation turned off, so I had read that there may be an issue between the Touch ID and animation reduction.  If that had not helped, I was going to turn the animation back on.
    Last night my phone seemed fine.  I did hear it restart in the middle of the night once, but this morning it will not power on at all.
    I tried connecting it to my computer through iTunes, but iTunes does not see it and I cannot access the device information from it.
    My phone is less than a month old, and for the first two weeks it worked great.  I am taking it into the AT&T Store today where it was purchased, but I don't really have high hopes for a resolution.
    Any help is much appreciated!

    Sorry AT&T store won't be much help.
    I suggest you make an appointment with the Genius bar and then go to the Apple store.

  • Macbook Pro will not power on without battery installed

    Hi there,
    I have a Macbook Pro A1226 that fails to power on without a battery installed.
    i.e. will not run off AC power on its own. I have tried 2 other power adapters, no change. All 3 adapters are outputting the correct voltage without fluctuations.
    But, if I am in OSX with a battery plugged in, shutdown the laptop, remove the battery while AC is still plugged in, it will power back on without any issues. But as soon as I remove the battery, it will not power back on using just AC.
    Is this an I/O board issue, or a mainboard?
    I have power drained the unit and reset the parameter ram.
    Thanks

    Any update on this? This is the same thing that's going on with my laptop right now. I was at the Genius Bar and they said they can send it in for repair. Takes 7-9 days and costs a minimum of $310. At the time I was there, my computer wouldn't start up at all, because the battery had drained to less than 20%. It didn't even start with just the power cord (no battery in). The "genius" finally got it to work by doing a PRAM and SMC reset. Got home and was able to recharge my battery to 100%. Used my computer for 2 days before I dared to take it off the power supply. Lo and behold, as soon as I take it off the power cord, then re-connect it, it shows "Not Charging". I tried to do SMC again, but no luck. Keeps saying "not charging". Even tried with a brand new battery. Do I have to get the I/O board thingy replaced?

  • Ipod touch generation  5 will not power on

    My ipod touch generation 5 will not power on though it was showing to b e fully charged.  I have been pressing and holding the on button on the top which usually cause a  the screen to light up.  Is there some way to get it to work?

    Try:                                               
    - iOS: Not responding or does not turn on           
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try another cable              
    - Try on another computer                                                       
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar                                     

  • My ipod touch will not power on or even be acknowledged by my computer when i plug it in, any  suggestions to the problem

    My Ipod will not power on, it is fully charged and if I plug in into the computer it doesn't even ackowledge it. Any suggestions?

    Try a hard reset and go from there.
    Basic troubleshooting steps. 
    17" 2.2GHz i7 Quad-Core MacBook Pro  8G RAM  750G + 120G OCZ Vertex 3 SSD Boot HD 

  • My IPOD Touch initially had a white screen.  I tried correcting this by restoring default settings via ITunes.  The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB

    My IPOD Touch initially had a white screen.  I tried correcting this by restoring default settings via ITunes.  The Restore Failed with error 1602 and now the IPOD touch is completely dead. It will not power on or respond when I plug it into my PC via USB.  I get an error on my PC stating that device attached to USB port is not recognizable.  Can anyone help?

    Error 1602: Try the following steps to resolve this error:
    Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
    Follow the steps listed for Error 1604.
    This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
    Above from:
    http://support.apple.com/kb/TS3694

  • HT4061 I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

    Can anyone help us please?
    I cannot switch my IPAD on and it will not power up - i had this problem before and cannot remember how we fixed it?

    Press and hold both the home button and lock button until the apple logo shows up.

  • My HP Pavilion dv9700 will not power up. Lights blink on and off on a cycle, but screen is black

    My HP Pavilion dv9700 will not power up.  Lights blink on and off on a cycle, but screen is black.

    Please post your Full Product Number
    http://h10025.www1.hp.com/ewfrf/wc/findModel?lc=en&dlc=en&cc=us

Maybe you are looking for

  • Osx+tuxera ntfs+itunes+windows == 150GB of data gone

    When i bought this mac (macbook pro 8,2) i had this nifty idea of repartitioning the hdd so that i would have a small osx and linux partition and all the space left for windows and data on one ntfs partition, i regret that now.... This idea was becau

  • Bootcamp Vista on low/mid-end MacBook ?

    Hi, I plan to buy a MacBook this week-end and I would need just little bit of information about it. My mom (yeah) would like to run Vista on my macbook, so she can start working on it (she teaches windows/office) this summer before she buys a new com

  • How do you export 4 discrete mono audio tracks with video from Adobe Premiere Pro 4/Adobe Encoder?

    I've posted this question in different terms a few times and have not had an answer.  I can't find the answer on the Premiere Pro support site either (which makes me think that a simple solution doesn't exist) We use adobe premiere pro 4.  We capture

  • How to install BootCamp5 drivers for Windows 8?

    I have a Mac mini and have installed Windows 8 (64-bit) using Bootcamp. It works fine, but I hear that you should install some drivers. I downloaded them from the apple support website and put them on a usb flashdrive that uses the format "MS-DOS (FA

  • Question re ENCODING cp option of OPEN DATASET statement

    I'm working on a 6.0 system with 4.6 data that I've downloaded from the 4.6 system and uploaded to the 6.0 system. The 4.6 data has "umlauts" in it (like when "o's" have two dots above them in Scandinavian names), and  when my READ DATASET executes o