Z68 WIN 7 will not boot after setting drive BIOS from IDE to SATA

MSI Z68MA-ED55 (B3) Motherboard
Windows 7 Ultimate 64 bit OS
SATA III Solid State Drive with greater than 500 MB/s throughput
After installing WIN7 and all my Applications programs I noticed in the BIOS that the driver for the SSD did not properly set to fully support the SSD but remained in the IDE mode.
This computer was built for technical graphics work and not for child's play. So I don't want to have to reinstall all the applications software for work with all its required protection features from theft.
QUESTIONS:
1. With this high transfer rate SSD, is it worth the performance improvement to reset the BIOS from the IDE driver to the proper driver?
2. If so, how can I set the BIOS to the correct driver without reinstalling everything?
3. At some level of the installation the system should have sensed the SSD SATA III and changed the driver from IDE. Where should this take place?

Hi,
I had the same problem. You need to put it back to IDE, boot to Windows then follow the below instructions and it works fine. (Courtesy of Guru3D)
Enable AHCI
The last tip we want to give you to gain a little extra performance boost is that you enable AHCI mode. AHCI mode can help out greatly in performance for SSDs. Now, if you swap out an HDD for an SSD with the operating system cloned and THEN enable AHCI in the BIOS, then you'll likely get a boot error / BSOD.
The common question is, is there a solution for this ?
To answer that question (and as we do safely with all modern chipsets) there is a way to safely enable AHCI mode. Here we go:
1. Startup "Regedit"
2. Open HKEY_LOCAL_MACHINE / SYSTEM / CurrentControlset / Services
3. Open msahci
4. In the right field left click on "start" and go to Modify
5. In the value Data field enter "0" and click "ok"
6. exit "Regedit"
7. Reboot Rig and enter BIOS (typically hold "Delete" key while Booting)
In your BIOS select "Integrated Peripherals" and OnChip PATA/SATA Devices. Now change SATA Mode from IDE to AHCI.
You now boot into windows 7 or Vista, and the OS will recognize AHCI and install the devices. Now the system needs one more reboot and voilla ... enjoy the improved SSD performance.

Similar Messages

Windows 8.1 will not boot after setting up dual-boot with Linux Mint 17.1 Cinnamon

In which forum should I ask this question?
After installing Linux Mint onto a partition of my hard drive, Windows 8.1 is listed a choice to boot into after restarting my computer, but will not boot up. It suggests a boot repair and to obtain Windows 8.1 from my distributor. I have seen on other forums
that this has not worked, and I was wondering if anyone here had any suggestions for how to proceed.
Thanks in advance.

You can try them over here.
http://answers.microsoft.com/en-us/windows/forum/windows8_1?tab=Threads
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

HP Pavilion 500 (desktop) will not boot after updating driver's.

Working on my mothers CPU but I cant seem to get past this screen now
This was after I had downloaded and installed drivers from this site. I cant seem to figure out why it is not going in to windows xp. Any ideas? It also was giving me a fan error which was easy to fix but cant seem to figure this out.

wow no one can help I guess everyone is duped as I am. DaRN HP

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Satellite Pro L300 will not boot after Bios update

Help please.
I have just formated a Satellite Pro L300 laptop.
I used all the updated drivers from Toshiba and all went very well.
I then updated the bios with the latest version.
After doing this the laptop will not boot but just keeps scrolling through the start menu and no matter what option I choose it just keeps doing the same thing.
Any ides welcome

Hi
I used the Microsoft installation disk but just keep getting to the same stage until the blue screen appears. I have tried different installation disks and also changed the hard drives as well. I can do everything in bios, change boot device enable or disable devices but that is it. I have tried a few times to instal windows but it just stops at the same point saying windows is stopping instal to protect the system. I fear the bios update has done some permanent damage as I cant get past the dreaded blue screen.Thanks anyway

Brand New 27" iMac i5 will not boot after installing software updates

I just purchased my new iMac 2 nights ago. I have been getting it setup with my apps, mobile me account, etc, and luckily just setup time machine and let it do a full backup.
I just ran Software Update for the first time, and now the machine will not boot. It hangs on the grey screen for about 1 minute before the Apple logo comes up. About 30 seconds after the Apple logo comes up, the grey spinning gear shows up, and about 1 minute after that I get the grey screen of death (You must restart your computer).
Any suggestions? A little frustrated here....

If you mean did I receive error messages, No, I didn't. However, the desktop reverted to the default purple night-sky looking thing, my applications and such all disappeared from the dock, and I couldn't open any files or folders (you don't have permission to ...), etc. I tried signing out and back in, rebooting, using a second admin account on the computer, creating a new admin account, etc. I ran Disk Utility, hardware checker, etc. No errors were found, and nothing changed. I could see all my files and folders, but they had a small red circle in the corner, indicating "locked" or "no permission".
I'll find the lines from the console log if that will help. The error showed up immediately and is in the computer's attempt to access the user/library/application support/sync services and same path to user/library/logs/sync services/log. (or something reasonably close to this. If you can use the exact path, I will get it) The link between my settings and files, and a password is apparently corrupted or something, so that the computer won't even let me change the desktop or any file, so I can't save, edit or discard anything, and can't drag files to another computer on the home network.
At least I'm still under the 90 day warranty, so I can call tomorrow. At this point, the SMART check says the drive is good, so I assume it's software. The only things new are the three auto Apple software updates I installed yesterday, so I immediately suspect them. But who knows?
Does this help you at all?

Snow Leopard will not boot after TM Restore

I had an email issue (lost 5 accounts) that has turned into a nightmare. Apple Support told me to restore my entire hard drive from my Time Machine. I booted to the DVD and selected a restore point and 12 hours later I get the Apple with the spinning wheel. I have tried two restore points - same result. It will not boot in safe mode either. I ran the Verify Drive utility and the drive checks out.
The drive is about 75% full after this TM restore operation so it appears it is pulling all of my data into the machine.
I have a number of backups of my system including a full one on ARQ plus all the TM backups. I am just not versed in the Apple OS enough to know how to recover from this point.
Q's:
1. Is it possible that the data and the Apps have been restored but the OS is simply corrupt on the TM?
2. Is there a Repair feature on the SnoL DVD or am I faced with a fresh install?
3. If I do a fresh install, can I simply copy the Apps folder back in the machine and my apps work correctly? (I realize a few may not that have to have components in browsers or whatever).
Suggestions on recovery approach...
Thanks, Uursa

uursamajor1 wrote:
1. Is it possible that the data and the Apps have been restored but the OS is simply corrupt on the TM?
Welcome to Apple's discussion groups.
That's possible. Once you can get it to boot you can explore that.
2. Is there a Repair feature on the SnoL DVD or am I faced with a fresh install?
Soon after booting from that DVD you should see a Utilities menu with Disk Utility under it. With Disk Utility you can perform a "Repair Disk" operation.
3. If I do a fresh install, can I simply copy the Apps folder back in the machine and my apps work correctly?
You could first try installing OS X 10.6 over what's already there. You might also learn more about what's wrong by doing a "verbose boot':
http://support.apple.com/kb/HT1492

Will not boot after disabling onboard sound

I am trying to install an SB Audigy2 ZS sound card but each time I disable the onboard sound card, I cannot boot my system. It will not boot to CD either. I have tried disabling with SB Audigy2 ZS card installed and without the card installed. I am using the third PCI slot since the video card uses the first slot's space.
I tried it without 2 of my hard drives in case I was running low on power, but still will not boot.
Any ideas?

i have the newer mobo and also have audigy zs it install just right for me but i have it in pci slot 4 (the last one on my mobo) your manual of your mobo will tell you which pci share the same irq ..but when i had your version of mobo i still had it in slot 4 so try pci 4 or 5 to see if that resolves your problem it souds like your video card and sound card are tying to share the same irq which is a big no no

White iMac will not boot after 10.6.8 upgrade

I downloaded the 10.6.8 upgrade last night. This morning, the white plastic iMac will not boot.
I have tried evey known keyboard option.
I have tried booting from the snow leopard dvd.
I have zapped the pram.
Nothing!
Please, any help would be great.

We bought 2 iMac's 27inch with i7 Quad-core. Did the update a couple of hours ago. My Mac asked to reboot after update, but i didn't accept and worked with iTunes for a while. Then rebooted manually. After reboot it took about 15 minutes to reboot (light-blue screen with nothing on it, not even a mouse). My Wife also did the update of 10.6.8 and rebooted when asked. Her iMac also took 15 minutes to reboot, bus update was unsuccesful! So did update again and then denied reboot and rebooted manually! (Apple-logo and then choose "restart").
When we did that, iMac was very fast and updateproblem was solved! So deny reboot and reboot manually and problems are over. Same deal with 2 brandnew iMac. I'm guessing this is an issue. To much of a coincidence for me!

Macbook Pro Will Not Boot After Full Timemachine Restore

Hope someone can help. I upgraded my HD and attempted to restore from time machine. Everything appears to have worked well and the restoration was a success according to what the computer says. However, when I go to reboot I hear the startup sound then the apple pops up on the screen followed by a kernal panic error and the black box telling me that I need to hold down the start button and restart. I've tried resetting the pram, reinstalling from TM again and a couple of other things but it won't start up. I tried doing a clean install and it worked fine then I migrated files from my TM backup and that worked fine as well. However, that's not what I'm looking for, I wanted to get the machine exactly the way it looked before the upgrade and I thought TM was supposed to do that. I've read other forums were people have done it with no problems and am completely stumped at why it is not working. If anyone can shed some light I'd appreciate it.

I booted with the CD and after selecting the language, went to the utilities pane and used the partition feature.
Last night in desperation, I booted back to the CD and once again told it to do a full restore from TM. This was the third time that I had done it so far. The previous two times I had gone into the partition feature and partitioned the drive first. This time I skipped that step and just told it to restore from TM. It said if it did this it would erase everything on the drive. I agreed and let it do its work. This morning it once again, as in both previous times, said it had restored from TM successfully. I told it to restart and lo and behold, it booted and everything is just as I had it on the other drive.
Needless to say, I'm confused but happy. I just wish I knew why it would not boot after restoring the previous two times? Maybe it just wanted me to spend more money:) I tried booting today only after I had gone to frys electronics and bought a SATA to USB cable and cloning software.
Anyway, thanks for your help and if anyone knows why it wouldn't boot, let me know. It would be good to know for the future just in case. For anyone else having this trouble, keep trying. Third time was a charm for me.

Will not boot after adding RAM?

I just added another 512mb chip to my PB G4 upper slot. After adding the RAM, my PB will not boot/ load the OS. When I press the power button, the HD (i think) begins to run, but stops after about 2 seconds. I can't get it to do anything else. Please help.

Have you taken the new RAM stick out yet?
Powerbooks can pretty picky when it comes to RAM.
Joe

Will not boot after updates

I have a macbook air. It is running Lion. After updates it will not boot. It starts installing updates and just stops all together. Any help would be very welcome.

Hey bfa67,
Thanks for the question. To isolate the issue, what happens when you start up in Safe Mode?:
OS X: What is Safe Boot, Safe Mode?
http://support.apple.com/kb/HT1564
Thanks,
Matt M.

Z68 WIN 7 will not boot after setting drive BIOS from IDE to SATA

Similar Messages

Maybe you are looking for