Z68A-GD65-G3 boots slowly

I have this board in my computer, and I have found out, that if I have my 3D Connexion Space Navigator connected, then boot time is extremely slow.
Is there a fix for this?
My system:
MSI- Z68A-GD65-G3
Intel i7 2600K
Corsair Vengeance 16GB CL9 Kit
Corsair Force 3 240GB SSD
Nvidia Quadro FX-3700

The device may not be fully compatible, meaning that a BIOS upgrade may be required.
Does this slow response happen with a standard USB mouse ?
Suggest you log a ticket with MSI technical to allow them to test and provide feedback.
Which BIOS version do you currently have?
You can also contact 3DConnexion to see if there is an updated firmware available.

Similar Messages

  • Z68A-GD65(G3) boot problems and random crashes

    Hi all,
    Built a new system last week:
    i5-2500k
    MSI Z68A-GD65(G3)
    MSI 6950 2Gb TFIII
    8Gb Corsair Vengence DDR3 PC3-12800C9 1600MHz Dual Channel
    Corsair HX650W PSU
    Crucial RealSSD M4 128GB SSD
    Posted fine on the first power-up but then hung at 'Starting Windows' just as the logo starts to fly-in.  After a lot head scratching, removal of GFX, an HD with an image of W7 on it already (exact same issue), RAM swops etc I discovered that the top pair of USB ports appear to be suspect. If any device is plugged into either of them then the system will hang at that point.  If I use the lower (non-USB 3.0) it boots just fine.
    I'm also experiencing an issue in games (BF3 and DCS A-10 so far) whereby I have a random freeze. The sound will go nuts and the lights on all USB attached devices go off (which make me suspect the 2 problems are related)
    Anybody able to offer any advice? Do support monitor these forums (newbie  ).

    Quote
    again, worth trying to disable external marvell sata3 ports
    Again, Marvell SATA III controller. SATA3 is a port on the mainboard.

  • MSI Z68A-GD65 (G3) Boot Loop

    Hello all,
    I purchased a MSI Z68A-GD65 (G3) and when I started up it goes into a boot loop. I can't see anything on the screen.
    Setup
    - Motherboard MSI Z68A-GD65 (G3)
    - Intel Core i3 Ivy Bridge 3220 3.30GHz 3MB Cache LGA 1155 55W Dual-Core Processor
    - Kingston ValueRAM RAM Module - (2 x 8 GB) - DDR3 SDRAM - 1600 MHz DDR3-1600/PC3-12800 - Non-ECC - Unbuffered - CL11 - 240-pin DIMM
    - COOLER MASTER Elite Power 400W OEM 20+4 pin & 4+4 pin ATX 12V V2.31 12cm fan Eco-friendly Reliability Quiet Noise Filter 70% efficiency
    BIOS stated in the green labels below the "MSI" Heatsink is: E7681 IMSN10.
    I tried another PSU and had the same issue.
    Anybody can help me? Thank you very much for your time!

    Your mainboard does not support an Ivy Bridge processor with the current bios that's why it doesn't come up. It needs a P series bios (7681vP1 and above).
    There is no other way than to use any Sandy Bridge cpu to flash bios to the latest to make your cpu work: http://www.msi.com/product/mb/Z68A-GD65--G3-.html#/?div=BIOS
    For flashing >>Use the MSI HQ Forum USB flasher<<
    If you can't get a hand at a Sandy you need to let any PC shop or MSI do it for you (that's not for free of course). >>How to contact MSI.<<

  • Z68A-GD65 (G3) very slowly with win8

    HI Everybody!
    Please help me!
    I have a Z68A-GD65 (G3) MoBo with 16GB DDR3 RAM. While i use win7/64 Ultim., my copy files results partitions to partitions 130-160MB/sec. I install win 8/64 Ultim. my copy results: 50-70 Mb/sec.
    I Install the latest win8 drivers from mis official site
    What can I do?
    thx anything answers.

    Try these drivers:
    http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22270&lang=eng&OSVersion=Windows%208%2C%2064-bit*&DownloadType=Drivers
    Other win 8 drivers:
    http://www.msi.com/product/mb/Z68A-GD65--G3-.html#/?div=Driver&os=Win8%2064

  • MSI Z68A-GD65 (G3) Boot Problem

    I found a beta BIOS on the MSI forum, and flashed from it. Now "UEFI:Windows Boot Manager" isn't showing under "Boot Option Priories", and as the drive was initially configured in AHCI mode and formatted with the GPT format, I need this option. It now lists my HD as a regular HD. This happened earlier, also, where I was flashing the BIOS with different versions in order to try to clear up BIOS bugs. Now I can't even boot into Windows as I just get a blinking cursor right after the BIOS screen. For some reason, the BIOS is filtering the "Windows Boot Manager" option and clearing the CMOS didn't help. I saw another post of a similar nature on here, and am wondering if there an EFI shell command to get this option back? I hope I don't have to return this board back to the vendor.
    Steps to reproduce the problem:
    1. HD set to AHCI mode
    2. Windows 7 x64 install went flawlessly
    3. Windows Boot Manager selected as option under Boot Option Priories
    4. Flash to any other version BIOS and Windows Boot Manager option completely disappears from Boot Option Priories
    5. Formatting the HD and reinstalling Windows brings back the Windows Boot Manager option

    Quote
    He said he laughed at MSI's response because it's wrong.
    Well, there is nothing wrong at all with MSI's response:
    Quote
    the issue you are experiencing has to do with the fact that the UEFI data is stored in the NVRAM which gets cleared whenever you update the bios. This so far as I was informed is not something we can change.
    This is the same thing you just said:
    Quote
    Pretty much, Windows writes to the firmware when you install it using GPT. If you update the BIOS, the NVRAM is cleared
    So, what is there to laugh about?
    Quote
    This so far as I was informed is not something we can change.
    Of course MSI cannot change that by any UEFI fix, as this seems to be an UEFI design obstacle.
    Quote
    but you can run a Windows emergency boot disk and issue a couple commands and get the data written back to the firmware.
    ... or use the tools mentioned in the articles I linked you to in my previous reply to backup & restore NVRAM data.

  • Z68A-GD65 G3 Booting takes long ...

    Hey Forum,
    when i start up my pc the first thing that appears is a prompt in the top left corner and at the bottom right it says "98" which changes later to "B4" and then it boots normal. Overall i would say this takes 1-2 minutes and then it boots normally.
    So I dont think this is a normal process does anyone have a clue ?
    Thank You
    i7 - 2600k
    Corsair Vengeance Ram 16 GB
    Corsair 750 PSU
    GTX 560 TWIN FROZR 2

    Your board does not use a standard/legacy BIOS but an UEFI implementation.  So, when I said "UEFI/BIOS Version" I meant the same thing:
    Quote
    Bios is V23.0 / 20110706
    Quote
    Logitech G510
    Steelseries XAI
    Especially the XAI mices make problems on other boards has well, problems that have been fixed in newer UEFI/BIOS releases.
    Can you please test without the mouse and a standard PS/2 keyboard attached?
    Does the system still hang @98/B4 if you do not use the XAI/Logitech combination?

  • Z68A-GD65 (G3) fails to boot with new Gigabyte Radeon HD 7950 OC

    Hi,
    I have a problem with my new Gigabyte AMD Radeon HD 7950 (GV-R795WF3-3GD):
    My system fails to boot with this GPU, with the old Radeon HD 4850 everything works fine.
    Here are my system specs:
    MSI Z68A-GD65 (G3)
    CPU: Intel Core i5-2500K
    RAM: 8Gb DDR3-RAM (Corsair)
    power supply: be quiet! Pure Power L7 530W
    What I have already tried to fix the problem:
    -CMOS Reset
    -other PCI-e slot
    -other power supply (old 750W)
    Nothing worked.
    Do I need a Bios update? My current version is V23.7, but I'm not sure whether I can use the latest versions because my CPU is a SandyBridge...

    We can't help you woth your vga as it is no MSI product. You can try latest bios for your board (http://www.msi.com/product/mb/Z68A-GD65--G3-.html#/?div=BIOS) because the latest bios versions for G3 boards are  working well with Sandy and Ivy. If latest bios should not help and you like to downgrade the bios we can give you the needed files if you ask here.

  • Z68a-gd65 boot loop after bios update using USB

    Hi there,
    My  z68a-gd65 (G3) went into a boot loop after I did a bios update from a USB key that I installed using the latest BIOS version on the MSI site 7681vP8.zip
    After the system restarted, it keeps booting up for 5 seconds and then shutting down, I removed all external devices and the Geforce GTX 550 Ti card and used the onboard card, but still no change...
    Is there a way to set the board to factory defaults again???
    Marcel

    Hi there,
    Maybe for others to solve the same problem, I found out what was the cause of this problem, I had a USB/Firewire card installed in the PC, after removing it the BIOS update could proceed from the USB stick as planned.
    After the update though, my USB/firewire card can still not be installed back into the slot, because doing so will make the boot loop appear again, very odd!
    Does anyone know why this new BIOS will not work with the card that has been inside my PC for 2 years???
    Marcel

  • MSI Z68A-GD65 (B3) Continuous Boot Cycle

    My Mainboard was running flawlessly, but yesterday when power on the system...I found that Continues boot cycle.
    The computer turns on for a few seconds then powers off. This cycle repeats every 5-10 seconds.
    Z68A-GD65 (B3)
    http://www.msi.com/product/mb/Z68A-GD65--B3-.html
    What are possible fixes/problems or I have to RMA it...please help
    I have tried clearing CMOS, swapped the psu, cpu, rams...and also tried with one ram stick at first slot near cpu and at at all other memory slots...but no success and same repeated automatic boot cycle every 5-10 seconds or so...
    my specs are..
    2600k
    Kingston 2x2 gb ram 1333mhz 1.5V...value ram
    Nvidia GTX280 GPU
    Delta branded 750watts psu

    Quote
    when i reset the cmos..on first second and third boot the BIOS led flashes..but on fourth it remain stable in that brief time it is powered.
    Could you clarify this a little? You mean the BIOS LED stays full off, or it is on steady?

  • Z68A-GD65 (G3) - Motherboard's not booting with a PCI Soundblaster Audigy 2.

    Hi everybody, as thread title says I've got some trouble with my motherboard, Z68A-GD65 (G3) and a Soundblaster Audigy 2 ZS that a friend of mine gave to me. I gave a try in both PCI slots avaiable on the motherboard but as i place the SB in PCI slot 1 or PCI slot 2 the system do not boot up. As soon as i take it off, the system works great as usual.
    Of course i disabled the onboard audio to avoid resource sharing between the two. This is the only hint i had reading around on MSI trobleshootin.
    The only other parameter i can change regarding PCI is latency in the BIOS. I found to be 32 cycle by default and i did not modified it.
    The Audigy works flawlessly on another Intel P45 Board from a different brand and with the same video card in the PCI-E Slot. Of course Cpu end Ram ar different. When i did the try i disconnected everything unnecessary for the boot process.
    Any hint would be very appreciated.
    Thanks, Daniele.

    As i read on manual, the PCI setting into the bios is not something can cause instability:
    PCI Subsystem Settings
    Press <Enter> to enter the sub-menu.
    PCI Latency Timer
    This item controls how long each PCI device can hold the bus before another
    takes over. When set to higher values, every PCI device can conduct transactions
    for a longer time and thus improve the effective PCI bandwidth. For better PCI
    performance, you should set the item to higher values.

  • Z68A-GD65 (G3) issues.

    I'll start with my build,
    Z68A-GD65 Gen 3
    i5 2500k under Noctura NH-D14
    16GB G.Skill DDR3 1333 CL9 1.5V
    MSI R6950 Twin Frozr II 2GB
    Crucial M4 128GB SSD (in 1st intel sata 3 port)
    Antec HCP 850w
    Bios 23.3 (or whatever, I'm on phone at work)
    A few issues;
    I can't OC. If I try an oc, it boots, I get splash screen for msi, then hangs with blinking underscore. Even if I match oc genie setting for setting in standard mode. Using auto etc, set v core way high (like 1.4 for a mild 4.2 oc) it just seems to hang. I'm guessing something to do with the sata 3 controller, since I'm booting off ssd
    Last night I started PC, went to bathroom, came back and it was loop booting. I hard powered it off, and restarted. OC failed, and that was oc genie at 4.2.
    PC won't wake up from sleep. Have to hard power off (hold power button down) then restart and it resumes windows. Mouse and two diff keyboards won't wake it (performance mx mouse, g510 keyboard, and ps2 dell keyboard.)
    G510 won't enter bios, have to use dell ps2 keyboard.
    If in OC genie, or trying oc in standard mode, system double posts. Starts, runs 4-5sec (no display), powers down, starts back up and runs fine for hours (except the one oc fail on genie)
    Any ideas on any of it?

    No, thats the last official release. There has been a host of beta BIOS releases since. I just flashed to the latest .N48 today and I must say, I am very happy with the stability I now have.
    If you intend to flash, use the forum flasher. >>Use the MSI HQ Forum USB flasher<<
    Do a full CMOS clear after flashing >>Clear CMOS Guide<<
    Also you will need to ensure that you set your BIOS back to AHCI, if you did that before installing the OS.
    I further suggest you remove all RAM except one stick in the slot closest to the CPU before the BIOS flash. Only put the other RAM back after you have been through one boot cycle.

  • Raid mode very slow/ crashing after installing driver (Z68A-GD65 (G3))

    I recently purchased a Z68A-GD65 (G3) motherboard, i5-2500K, 8 gb ram, and a Crucial 64GB 4m SSD drive. The intention was to use the SSD drive for Intel Smart Response Tech.
    Instructions tell me to place the SATA ports in RAID mode, which I did. During installation of Windows 7 (64-bit), I provided the "F6" raid drivers which installed. After that point, my hard drive (a WD 250GB SATAII drive) begins to perform incredibly slow. Once Windows 7 installs, which takes way longer than it should, Windows has problems booting and won't work properly.
    I tried installing Windows 7 without the "F6" raid drive on install and that worked fine. Everything seemed to be working great. I then installed the Intel Rapid Storage Tech software and rebooted. Now my system is acting up again. It takes far longer to boot, it shuts down as soon as it boots, and it has even blue screened on boot. It is very unstable.
    My SSD is unplugged during all of this. I'm just trying to get Windows 7 to run properly on my one mechanical drive in raid mode.
    Do I have a bad motherboard? Anyone have any ideas?
    Edit: I'm not using the Marvell ports. The hard drive works fine in IDE/ACHI modes... I've been using it for years.
    Thanks

    So it turned out that the issue was the hard drive itself. It had been running flawlessly for years as my system drive. However, the Intel iastor driver exposed a hidden issue with the drive.
    I decided to check the Windows system event log for any clues. In there I saw errors with event id 9 on iastor. They were lined up with the times of the hangs and blue screens. Solutions I found online for this issue did not help. Luckily I have two hard drives in my system, although they are both the same model. I moved my data around and clean installed Windows on the other drive instead. The hangs and blue screens are no longer occurring.

  • Z68A-GD65 (G3) Memory problems after BIOS update

    Good day, i'm russian, so sorry for my english.
    Friend of mine had MSi Z68A-GD65 (G3), i5-2500K, memory pair 2*2GB with bios 22.8 (latest version with no red letters about ME8 and IvyBridge).
    He decided to upgrade the processor to IvyBrydge and updated bios with new ME8. Then the computer went into a state of continue restarting every 3 seconds. After replacing the CPU to the new Ivy - computer works good, the impression is that the computer does not understand Sandy now and switched toIvy. But it has seen only one of memory pair. My friend just bought a new motherboard. Now he has no problems. I took his MB and SandyBridge CPU.
    Flashing the bios to the old version by M-Flash - it does not see the BIOS file, although it is there (in the root, FAT, 2G). Flashed it under dos with AFUDE238 with a key -x, it said about mismatched ROM ID. After the old BIOS flashing (with an Ivy) computer went three-second reset mode. CPU changed to Sandy i5-2500K - now works good. By the way, now M-Flash see the firmware on a flash drive - I flashed it again from the M-Flash, just in case, reset the settings.
    What is the problem: if I set the memory into the slot 3 or 4, the computer goes into a three-second reboot, it does not matter is the memory in the first two slots or no. If this memory is inserted in the first two slots - all ok. So I work now - in the first two slots with no dual-channel mode.
    The feeling is that the problem appeared after first flashing to Ivy and remained after flashing back to Sandy.
    Question 1: What to do to get working the memory slots?
    Question 2: Is BIOS 22.8 - the latest which I will have with Sandy? (There is a problem now when the computer starts - 1 times out of 10 will not boot - reset is helping, and the BIOS at starting not very fast).
    There are posts about people with the same MB and the CPU and the new BIOS (25.2) that supports Ivy. I'm confused. It means I can use the new firmware from SandyBridge. But there are many posts about problems with new firmware. Where is the true?
    Just checked BIOS version -  P.1 (25.1) 2012-04-16 - by the way with Ivy support. But I flashed with 22.8, I'm sure. ME version in BIOS isn't shown, but while booting - ME 7.0
    What does it mean? Can it be repaired? What should I do?

    Thanks to all. My system is working fine now.
    What it was. I flashed BIOS with tool from this forum. Bios flashed good, but problem still was here. Then I flashed to the first bios version from support site. And again flashed ok but memory still not working in slots 3 and 4. Then I decided to flash back to last flash with Sandy support 22.8 (or 23.8). Then I flashed to the last bios at all - 25.4. Flashed it from dos - this was pretty long. It rebooted 3 times (ME updated too). I still don't know  - what it was with first flashing to Ivy. Now it's ok.
    So I decided the problem is bent pin. With magniglass and needle I've found some uncertain pins (these were not BENT, but slightly bent) and touched these with my needle. And that was the answer. Now all works fine. Thank you all.
    On the russian msi forum no one answered and helped me at all.

  • Z68A-GD65 G3 No video on GPU, IGD works fine

    Hello everyone. I'm making a post on a recent board, mainly the MSI Z68A-GD65 G3, that I've received from a previous RMA due to bad pins. This one boots up normally just fine when plugged into VGA, DVI, and HDMI directly and able to use Windows with no problem. So I use my EVGA GTX 750 that I saved up for the new MB  However, once I try to install my gpu and power it up it doesn't show any sign of post nor boot screen avail. I've updated the bios to the beta from .80 to .93, cleared cmos, and tried installing Intel ME8 afterwards from reading other posts with the same issues. Yet, after some of the suggestions that I've tried out it still shows a blank screen with no post code nor progress whatsoever. I switched the GPU around to the second PCIe slot and tried out my older GTS 250 ones as well, no dice. Is there anything that I'm doing wrong or any alternative that I can try to make it show?
    Board: MSI Z68A-GD65 G3
    Bios: Version: 25.93B
    VGA: EVGA GTX 750
    PSU: Corsair TX850W
    CPU: Intel i5 2500 3.30 GHz
    Mem: 8GB 2x4 Kingston PC3-8500 DIMM 1066 MHz DDR3
    HDD: Western Digital 1TB
    CPU Fan: Intel i5-2500 Processor Fan
    OS: Windows 7 x64 Ultimate
    Any help is greatly appreciated. 

    Quote
    GTS 250 also shows a blank screen with no post code?
    Did you attach the PCI-E power cable, and update the vbios?
    PCI-E cables are connected to it since the GTS 250 requires them, but the 750 doesn't. So they do run fine when I tested them out once more on my old EVGA motherboard. Not sure how to update the vbios, but that sounds like a good idea to give it a shot.
    Quote
    Id this the first time you try VGA card in it since it was RMAd?
    If it is I suggest you take it back with them.
    Well the GTX 750 was recently bought brand new and I tested it out on my previous motherboard along with a friends system as well. It showed up properly with no problem. The z68a motherboard was the one I had to RMA because of broken pins on the CPU slot that gave me an infinite boot loop. Even when plugged into the system and using the onboard graphics, it seems that the board doesn't even detect it in the device manager. I do see 'Unknown Device' in it, but it doesn't exactly tell if its for the VGA card or something else.

  • Z68A-GD65 (G3) not always finding ocz vertex 3

    Me and a friend just bought identical setups, among them was the Z68A-GD65 (G3) motherboard and OCZ Vertex 3 120GB SSD. Both of us get some random crashes and sometimes when trying to boot the computer the SSD does not show up in BIOS (therefore can't boot from SSD). This also happens after a random crash. This usually gets temporarily fixed if you do a hard reboot. However it is very annoying when the computer freezes randomly (can be days between freezes). When BIOS cant' find the SSD it takes a longer time to show the mobo splash screen thingy.
    It is noteworthy that when doing a "hard reboot" it sometimes takes the computer about 5 seconds to startup after pressing the power button.
    Anyone got an idea how to fix this?
    I don't really know how i would go about solving this as it works most of the time so i don't want to fiddle with things i don't completely understand.
    System spec:
    CPU: i7 2600K, 3.4GHz
    Motherboard: MSI Z68A-GD65 (G3), v 23.1
    RAM: 4xCorsair Vengeance Low Profile 4GB DDR3 PC-12800 1600MHz (16GB total)
    GPU: Sapphire HD6950 1GB
    SSD: OCZ Vertex 3 120GB
    OS: Windows 7 Ultimate
    PSU: 650W Corsair

    Quote from: Henry on 17-October-11, 06:59:47
    Check with OCZ for the latest firmware update and see it that fixes your problem.
    Had to install Linux for that and had alot of trouble, but after some hours i finally updated the firmware.
    We will see if it ever happens again.

Maybe you are looking for