Z68A-GD65 G3 Reboot Loop

I'm putting together a new build and I've run into a reboot loop.  When I attempt to start it up, it runs for about 5 seconds, then turns off.  This goes on in an endless loop.  It never gets to POST.  The 6 LEDs light up and the BIOS ones don't (so this appear normal).  I have never gotten a successful bootup.
My setup:
Motherboard: Z68A-GD65 G3
CPU: Intel Core i5, i5-2500K
Memory: Kingston HyperX (4x4GB DDR3 - 1600 CL9 240)
Power Supply: OCZ ZX Series 850W
CPU Cooling: Xigmatek Gaia SD1283
I am not listing anything else, because I am not getting far enough for it to matter.
I am running with only the above pieces connected to rule out all but the essentials.
I've inspected the CPU and slot.  Both appear fine.
I've cleared the CMOS using the button on the I/O panel and removing the battery.
I've subbed out the Power Supply.
Only the 8 pin CPU and 24 pin motherboard connections are made.
I've tried various things with the RAM.  All 4, just 2, and just 1 (in the DIMM1 slot).  Most testing was done with just 1.  I have tried all 4 in the DIMM1 slot.
I've removed it from the case and booted it up in the cardboard box (nonconducting) it came in, to rule out a short.
I've inspected the motherboard carefully, no obvious issues.
I've checked that the CPU cooler is making good contact with the CPU.
I've verified that the OC button is not active, although I've tried that too.
I've read through the forums, but have not been able to find a solution that works.
Please help.  Thanks.

I had this very same problem with a Biostar T-POWER I55 2 years ago, to cut a story short the retailer and the distributor who handled Biostar RMA's rejected the RMA.
I spoke to Trading Standards/Consumer Direct as I read in the Sales Act that in the first 6 months of a purchase if the damage cannot be proven to be done by the end user then a warranty claim still exists.
Finally after stating this & quoting the Trading Standards Reference number to the retailer, I got a call from them saying they would offer a refurbished motherboard worth £113, my original motherboard cost £138 so I refused this & asked if they would agree if I could purchase a brand new alternative for (£75ish) around 50% of its purchase value to which after another day they rang back & agreed.
You are not the first and won't be the last this has happend too, One manufacturer will cover for warranty in these circumstances because I asked them.
I suppose you could get a 2 year warranty via Amazon, small expense for peace of mind which covers you for Accidental damage as well as mechanical failure, quite good if the  motherboard pins snap off the motherboard.
Click >> SquareTrade 2-Year Warranty Plus Accident Protection (£150-175 Items) £29.99
The above only complys to people in the UK, other countrys have different sales of goods act laws.

Similar Messages

  • MSI Z68A-GD65 (G3) Boot Loop

    Hello all,
    I purchased a MSI Z68A-GD65 (G3) and when I started up it goes into a boot loop. I can't see anything on the screen.
    Setup
    - Motherboard MSI Z68A-GD65 (G3)
    - Intel Core i3 Ivy Bridge 3220 3.30GHz 3MB Cache LGA 1155 55W Dual-Core Processor
    - Kingston ValueRAM RAM Module - (2 x 8 GB) - DDR3 SDRAM - 1600 MHz DDR3-1600/PC3-12800 - Non-ECC - Unbuffered - CL11 - 240-pin DIMM
    - COOLER MASTER Elite Power 400W OEM 20+4 pin & 4+4 pin ATX 12V V2.31 12cm fan Eco-friendly Reliability Quiet Noise Filter 70% efficiency
    BIOS stated in the green labels below the "MSI" Heatsink is: E7681 IMSN10.
    I tried another PSU and had the same issue.
    Anybody can help me? Thank you very much for your time!

    Your mainboard does not support an Ivy Bridge processor with the current bios that's why it doesn't come up. It needs a P series bios (7681vP1 and above).
    There is no other way than to use any Sandy Bridge cpu to flash bios to the latest to make your cpu work: http://www.msi.com/product/mb/Z68A-GD65--G3-.html#/?div=BIOS
    For flashing >>Use the MSI HQ Forum USB flasher<<
    If you can't get a hand at a Sandy you need to let any PC shop or MSI do it for you (that's not for free of course). >>How to contact MSI.<<

  • Z68a-gd65 boot loop after bios update using USB

    Hi there,
    My  z68a-gd65 (G3) went into a boot loop after I did a bios update from a USB key that I installed using the latest BIOS version on the MSI site 7681vP8.zip
    After the system restarted, it keeps booting up for 5 seconds and then shutting down, I removed all external devices and the Geforce GTX 550 Ti card and used the onboard card, but still no change...
    Is there a way to set the board to factory defaults again???
    Marcel

    Hi there,
    Maybe for others to solve the same problem, I found out what was the cause of this problem, I had a USB/Firewire card installed in the PC, after removing it the BIOS update could proceed from the USB stick as planned.
    After the update though, my USB/firewire card can still not be installed back into the slot, because doing so will make the boot loop appear again, very odd!
    Does anyone know why this new BIOS will not work with the card that has been inside my PC for 2 years???
    Marcel

  • BIOS 4.3 half flashed on MSI P67A-GD65 reboot loop ME not installed

    Hi, yesterday I tried to flash my bios from 1.19 (1.jo) to 4.3 and I followed the SOP guidelines. Made a flash fat32 got bios on it, started it, stopped all my applications under windows and it went with no error. PC Restarted and now it's in infinite reboot loop. The moment the MSI BIOS logo appears, the PC auto reboots.
    If I remove the usb drive or replace the bios file with another version it tells me it's not the file it needs. When I insert the one with the .43 file it goes back to reboot cycle. I tried resetting the CMOS with the button on the mainboard and I have this screen telling me BIOS is 4.3 and it has recognized all my 12gb ram, 2 hard drives and processor. Then it has press F1 to enter setup and press F2 to continue, both options result in reboot.
    I tried the 1.JO on flash, but it tells me again that it's the wrong file. Tried renaming it to amiboot as I found somewhere, but to no avail. Tried renaming the .43 to EIVB.bin as it was suggested in one forum, again no luck.
    System specs:
    OS: Windows 7 64bit
    Mainboard: MSI P67A-GD65 (not B3)
    CPU: Intel Sandy bridge i5-2500k @3.3ghz
    RAM: 2x2gb Kinston 2x4gb Gskill DDR3@1333hz 10600 CL7
    GPU: Nvidia Gigabyte G1 Gaming GTX 970 (reason I wanted to flash bios)
    PSU: Seasonic 80+ platinum 650W
    HDD: WD Caviar Green 2GB
    SSD: Corsair 60gb
    DVD: Liteon burner

    Quote from: Svet on 22-February-15, 19:25:45
    older non B3 versions ME can't be flashed,
    therefor you will brick it if you attempt to do it via MSI's all in one updater..
    you can try anyway to try with barabone setup with 1 memory stick only and disconnect everything that's not required to boot
    and to try the USB key in any of the other USB ports
    and/or with different USB key too
    to see if ME update will able to continue
    I wasn't sure about the ME update, read that someone managed. The Live Update 6 did my 1.19 (1.JO) update. I tried all usb slots and 3 different sticks, formated them and so on. Nothing worked. I tried disconnecting all hard drives and DVD drive too.
    Is there a way to stop this cycle or to restore to the 1.19 version?

  • [P67a-GD65] [Ivy] Infinite reboot loop after flash

    MSIHQ: Information detected by MSIHQ Tool ver: 1.25g
    MSIHQ: Report generated in Tue 01/01/2013 at 13:31:41.33
    Mainboard:  P67A-GD65 (MS-7681) - CPU i5-3570K
    PCB Version:  2.0
    BIOS Version: V4.2
    BIOS Date:  7/16/2012
    Attempted to upgrade to https://forum-en.msi.com/index.php?topic=164135.0
    Due to the inability to hold any overclocks with any voltage besides auto, and because the Windows MSI control center wouldn't keep settings on startup.
    Installed the forum flash tool on a USB drive and it wasn't bootable.
    Tried with another flash drive and it wasn't bootable.
    Used the on-BIOS tool to flash the BIOS
    Flashed, rebooted, and began reboot looping.
    Cleared CMOS - nope
    Removed battery and cleared CMOS - nope
    Removed all but one stick of RAM - nope
    Is it bricked? If so, how do I get a replacement/repair?
    Edit, was perusing the forums and found this:
    Forum flasher defaults to looking for zip files, if you pick rar from the drop down it should accept the file just fine, if you don't use method 1 you won't get the ME flashed.
    It's lovely that that's documented and pointed out in the flashing tool's post, and it's rather odd that all of the BIOSes are saved in .rar archives if the flasher looks for .zip. I used method 2.

    Quote from: Svet on 02-January-13, 04:35:53
    You should use "Fix My USB key" Tool's option 1st before prepare the stick if you having troubles booting from the USB key.
    I realized that after the fact.
    have you done >>Clear CMOS Guide<< with power cord removed and leave 1 memory stick only in 1st DIMM close to CPU socket?
    I just did that, and it unfortunately continues to loop.
    I guess I'll get it packaged up and into the mail. Thanks for the help guys.
    When I do get it fixed, what BIOS will it come with?

  • MSI Z87-GD65, Freezing while gaming, then reboot loop/bsod/total failure.

    Hey fellow MSI'ers
    Im hoping to find a solution for my problem i have been getting. I build a custom gaming rig a few months ago (specs below)
    Sinds a couple of days iv been getting wierd problems, System runs fine, i can do everything watch movies do work stuff. But when i start gaming it will work great for about 15-30 minutes, then i hear a click/beep thru the sound system, and a total pc freeze, screen freezes nothing works.
    So i hit the reboot, then the system decides to turn itself off and get into a reboot loop, turning on for few seconds then turning off again for a few back on for a few, etc etc.
    Only way i can get it running is pull the power, make sure the Motherboard has no charge left, then wait a bit and replug the power. Most times it will boot up fine and story starts at part 1 again.
    First off i thought it would be temperature, tho im running a almoost ull watercooled system, (Ramm + cpu + video) and i put up temp controlls on my seconds screen, and they never got above 35, on any of the components.
    Now seeing my build it is extreemley hard to quickly test a diffirent component, been running memtest with no problems, But when i do graphx/cpu stresstest/benchmark i get the same issue.
    As i stated before it has been running perfectly for few months.
    I read that PSU might be a problem, compatability wise with Haswell, tho then it wouldnt have worked for so long and just now giving these strange problems.
    What i tryéd so far:
    -Reinstall windows
    -Flash bios
    -clear bios
    -unplug as much as possible
    -diffirent ramm
    -Running with or without crossfire enabled.
    All same problems, i hope somebody has a idea without having to pull apart my custom build.
    Specs:
    -Cooler Master HAF XB
    -Intel Haswell 4770k
    -MSI Z87-GD65
    -2x Asus 7970 in Crossfire.
    -Corsair Dominator GT 2x4gb
    -Corsair ForceGT 128GB SSD
    -Antec TruePower 1200
    -2x 512gb Seagate MomentusXT

    Hi again,
    Quote from: robinvanesch on 03-October-13, 04:33:35
    UPDATE: Been running bencharmks/stresstest from onboard graphix, both cards disconnected. (lots of towels to be sure) and runs without problems, tho reallo low fps but thats expected.
    Going to see if i can run 1 card at a time, see if i can cause the problem to happen again.
    So did you agtually try it?
    Yep, bleeding is nice job and dooing it right on all steps is needed so yeah great, but if your CPU can handel the stress and you have tested the PSU then i cant see other way.
    Tip: take the hard loop,pipe, bridge(betwean the blocks away and add two 90angle fittings with long tobe, so you can rest each card away the pc 1 at time that way you dont need to bleed the system bitwean.
    (allso rest of the toops needs to be so long that it can be far away...)
    And yes you need reg edit your SATA drivers like xmad sayd, if you like to change IDE to RAID.
    P.s. nice build! Hope you get it working 
    Edit: You dont need to insert that PSU in the case, just connect wires whrere they need to be, at the momen for testing.
    Edit2: My current needs little service and update( add backplate, water change, delid cpu and moving GPU to bottom slot).
    Edit3: Wait that one 120mm low Rad keeps your sytem 32c??? Damn you have great chips, cold house or software issue. need for delid main is the heat i dont like and i have hmm 10 times that space to get heat off :D

  • Z68A-GD65(G3) Won't Post, Continuos Reboot

    I've tried everything I can think of other than trying a totally new product of motherboard.  Anyone have any ideas or suggestions?

    I can do that.
    MB: Z68A - GD65(G3)
    Processor: Intel i7-2600K 3.5 GHz, LGA1155 95W 8mb Cache
    Ram: 2 x Corsair 8 gb 1333 MHz in slots 1 and 3
    PCI-E: MSI N560GTX-Ti Twin Frozr II 2GD5/OC GeForce GTX 560 Ti
    PCI-E: Palit NE5X56T01142-1041F GeForce GTX 560 Ti
    OS HD: Intel SSD 320 Series 120 GB
    Other HDs: 2 x Western Digital Caviar Black WD1002FAEX 1TB 7200 RPM SATA 6.0Gb
    PSU: Raidmax RX-1000 AE
    Optical: Pioneer 18X DVD±R DVD
    Anything I'm missing?

  • P67A-GD65 reboot loop issues

    Seems like whenever I try to overclock my RAM or mess with the bios my tower would shut off and go into a reboot loop.
    What does this mean?
    Is my motherboard defective or is this what it does when a bios setting is messed up? The only way to fix the loop is to switch off the power supply and restart it that way. I've noticed it also does this if I use the MSI control panel to overclock my CPU sometimes.
    I'm starting to use MSI control panel and having much better luck overclocking compared to the MSI Bios. Is my chipset defective or is MSI's bios really this crappy...So annoying when it starts doing the reboot loop after adjusting acouple settings in the bios.
    I'll admit I'm not really an experienced OC'er so I might just not know what I'm doing. I tried upping the ram voltage to 1.65ish and OCing to 1600 with auto ram timing, but it just does the reboot loop after saving and exiting the bios. I haven't tried OCing my ram via the control panel, but upping my bclk on the control panel works well up to 105.5 bclk so far, while upping the bclk in the bios to even 100.1bclk does the reboot loop crap...I know upping the bclk is not reccomended, but I've had it at 105 on my other motherboard for over a month with no problems. I just got this board today and I'm having lots of issues with the bios...
    Anyways, I'm trying to get a ram oc of 1600. Could anyone help me in this regard thats savy with this motherboard?

    Quote from: LivingChampion on 10-March-11, 04:56:51
    I also have my ram sticks on the first and third slot if that makes any difference.
    Not really, but the blue slots are the recommended slots to use. From what I am seeing, there is no XMP profiles for your RAM. What that means is, reaching a stable 1600 RAM speed may be a bit of a challenge, or possible. Recommend with setting 1600, to try CR 1 (or 2), 9 9 9 25, tRFC 88 (or maybe 103), @ 1.60-1.65v's & give it another try.
    Added: Actually, running the RAM at the settings shown in the Memory Tab, is not a bad thing. Having done a few tests, the performance difference between RAM at 1333 & 1600 is pretty low. Sometimes only a few FPS.

  • Z68A-GD65 (G3) issues.

    I'll start with my build,
    Z68A-GD65 Gen 3
    i5 2500k under Noctura NH-D14
    16GB G.Skill DDR3 1333 CL9 1.5V
    MSI R6950 Twin Frozr II 2GB
    Crucial M4 128GB SSD (in 1st intel sata 3 port)
    Antec HCP 850w
    Bios 23.3 (or whatever, I'm on phone at work)
    A few issues;
    I can't OC. If I try an oc, it boots, I get splash screen for msi, then hangs with blinking underscore. Even if I match oc genie setting for setting in standard mode. Using auto etc, set v core way high (like 1.4 for a mild 4.2 oc) it just seems to hang. I'm guessing something to do with the sata 3 controller, since I'm booting off ssd
    Last night I started PC, went to bathroom, came back and it was loop booting. I hard powered it off, and restarted. OC failed, and that was oc genie at 4.2.
    PC won't wake up from sleep. Have to hard power off (hold power button down) then restart and it resumes windows. Mouse and two diff keyboards won't wake it (performance mx mouse, g510 keyboard, and ps2 dell keyboard.)
    G510 won't enter bios, have to use dell ps2 keyboard.
    If in OC genie, or trying oc in standard mode, system double posts. Starts, runs 4-5sec (no display), powers down, starts back up and runs fine for hours (except the one oc fail on genie)
    Any ideas on any of it?

    No, thats the last official release. There has been a host of beta BIOS releases since. I just flashed to the latest .N48 today and I must say, I am very happy with the stability I now have.
    If you intend to flash, use the forum flasher. >>Use the MSI HQ Forum USB flasher<<
    Do a full CMOS clear after flashing >>Clear CMOS Guide<<
    Also you will need to ensure that you set your BIOS back to AHCI, if you did that before installing the OS.
    I further suggest you remove all RAM except one stick in the slot closest to the CPU before the BIOS flash. Only put the other RAM back after you have been through one boot cycle.

  • Raid mode very slow/ crashing after installing driver (Z68A-GD65 (G3))

    I recently purchased a Z68A-GD65 (G3) motherboard, i5-2500K, 8 gb ram, and a Crucial 64GB 4m SSD drive. The intention was to use the SSD drive for Intel Smart Response Tech.
    Instructions tell me to place the SATA ports in RAID mode, which I did. During installation of Windows 7 (64-bit), I provided the "F6" raid drivers which installed. After that point, my hard drive (a WD 250GB SATAII drive) begins to perform incredibly slow. Once Windows 7 installs, which takes way longer than it should, Windows has problems booting and won't work properly.
    I tried installing Windows 7 without the "F6" raid drive on install and that worked fine. Everything seemed to be working great. I then installed the Intel Rapid Storage Tech software and rebooted. Now my system is acting up again. It takes far longer to boot, it shuts down as soon as it boots, and it has even blue screened on boot. It is very unstable.
    My SSD is unplugged during all of this. I'm just trying to get Windows 7 to run properly on my one mechanical drive in raid mode.
    Do I have a bad motherboard? Anyone have any ideas?
    Edit: I'm not using the Marvell ports. The hard drive works fine in IDE/ACHI modes... I've been using it for years.
    Thanks

    So it turned out that the issue was the hard drive itself. It had been running flawlessly for years as my system drive. However, the Intel iastor driver exposed a hidden issue with the drive.
    I decided to check the Windows system event log for any clues. In there I saw errors with event id 9 on iastor. They were lined up with the times of the hangs and blue screens. Solutions I found online for this issue did not help. Luckily I have two hard drives in my system, although they are both the same model. I moved my data around and clean installed Windows on the other drive instead. The hangs and blue screens are no longer occurring.

  • Z68A-GD65 (G3) Memory problems after BIOS update

    Good day, i'm russian, so sorry for my english.
    Friend of mine had MSi Z68A-GD65 (G3), i5-2500K, memory pair 2*2GB with bios 22.8 (latest version with no red letters about ME8 and IvyBridge).
    He decided to upgrade the processor to IvyBrydge and updated bios with new ME8. Then the computer went into a state of continue restarting every 3 seconds. After replacing the CPU to the new Ivy - computer works good, the impression is that the computer does not understand Sandy now and switched toIvy. But it has seen only one of memory pair. My friend just bought a new motherboard. Now he has no problems. I took his MB and SandyBridge CPU.
    Flashing the bios to the old version by M-Flash - it does not see the BIOS file, although it is there (in the root, FAT, 2G). Flashed it under dos with AFUDE238 with a key -x, it said about mismatched ROM ID. After the old BIOS flashing (with an Ivy) computer went three-second reset mode. CPU changed to Sandy i5-2500K - now works good. By the way, now M-Flash see the firmware on a flash drive - I flashed it again from the M-Flash, just in case, reset the settings.
    What is the problem: if I set the memory into the slot 3 or 4, the computer goes into a three-second reboot, it does not matter is the memory in the first two slots or no. If this memory is inserted in the first two slots - all ok. So I work now - in the first two slots with no dual-channel mode.
    The feeling is that the problem appeared after first flashing to Ivy and remained after flashing back to Sandy.
    Question 1: What to do to get working the memory slots?
    Question 2: Is BIOS 22.8 - the latest which I will have with Sandy? (There is a problem now when the computer starts - 1 times out of 10 will not boot - reset is helping, and the BIOS at starting not very fast).
    There are posts about people with the same MB and the CPU and the new BIOS (25.2) that supports Ivy. I'm confused. It means I can use the new firmware from SandyBridge. But there are many posts about problems with new firmware. Where is the true?
    Just checked BIOS version -  P.1 (25.1) 2012-04-16 - by the way with Ivy support. But I flashed with 22.8, I'm sure. ME version in BIOS isn't shown, but while booting - ME 7.0
    What does it mean? Can it be repaired? What should I do?

    Thanks to all. My system is working fine now.
    What it was. I flashed BIOS with tool from this forum. Bios flashed good, but problem still was here. Then I flashed to the first bios version from support site. And again flashed ok but memory still not working in slots 3 and 4. Then I decided to flash back to last flash with Sandy support 22.8 (or 23.8). Then I flashed to the last bios at all - 25.4. Flashed it from dos - this was pretty long. It rebooted 3 times (ME updated too). I still don't know  - what it was with first flashing to Ivy. Now it's ok.
    So I decided the problem is bent pin. With magniglass and needle I've found some uncertain pins (these were not BENT, but slightly bent) and touched these with my needle. And that was the answer. Now all works fine. Thank you all.
    On the russian msi forum no one answered and helped me at all.

  • Z68A-GD65 (G3) Component Advice

    I am in the process of putting together my first PC and look like getting a Z68A-GD65 (G3) board.
    The CPU will be a i5 2500K, but I would like some advice regarding ram and the CPU cooler. I intend just using the O/C button on the board method of over clocking as I am new to over clocking. I will be adding 8 gig system ram. What ram have people been using that causes no problems.
    With regard to the CPU cooler I have read a few reviews where the bottom support bracket on the back of the board fouls with one on the board heat sink mounting screws. From the pictures one screw is close the the mounting hols.
    The cooler I am thinking of is the Noctua NH-C12P, but it has quiet a big back plate. The other one I am looking at is the Cooler Master Hyper 212 EVO. I tend to like coolers that have back plates and screws to mount them rather than push pins as they are easier to reuse and mount firmly.
    Are these coolers good enough for my overclocking needs. I hope the auto overclock will give me just over 4 gig which will be fine for me.
    For the case I will use a HAF X or a Corsair model, should have enough airflow.
    So what ram have people used with this board that overclocks well and does not cause reboots during the overclocking process, and of course the CPU cooler.
    This is my first full build, and first go at overclocking so I am looking at compatibility and reliability over performance, and I do not need a big overclock for my needs. This is  a build mainly for FSX flight simulator.
    Also from reading some posts here I will need to flash the BIOS as well. The process described here to flash the BIOS seems complicated to what I have done in the past which has been on gigabyte boards only. I used to just download a small exe and run it from within windows. Is that possible with this board as I do not understand the process from what I have read here in the forums?
    I presume my choice of mother board from the MSI range is right from my needs, if not please recommend what I should be using.
    Any advice will be appreciated.
    Regards MarkL

    Quote from: HU16E on 10-March-12, 20:18:08
    Zalman 9900 series. Copper version up to the Max-B. Superior cooling ability. No blocked dimm slots & no mount hole problems. As for RAM, Corsair GT's, Vengeance, or Dominators are my brand of choice. DDR3 1333 is the platforms CPU IMC native supported RAM speed, & testing has proved RAM speed above 1600 is mostly a waste of time & money for a gaming rig, with only a slight performance gain when rendering. The most trouble free RAM will be kits that properly default to the 1333 speed. X.M.P. can be used, or manual settings above 1333 can be tried.
    That choice of mainboard should serve your requirement quite nicely.
    I have a question about the memory. I have been looking at the Corsair Vengeance range that I can buy online in Australia and they all seem to be 1600 not 1333.
    PC Case Gear seems to have the best range, but they are inconsistent in the way they give the specs, at least to my understanding which is next to nothing.
    http://www.pccasegear.com/index.php?main_page=index&cPath=186_218_1125
    The closest I can see is the "Corsair Vengeance CML16GX3M4A1600C9 16GB (4x4GB) DDR3" kit.
    This kit has a SPD speed of 1333, speed rating of PC3 12800 (1600 MHz) and a tested speed of 1600. Voltage is 1.5v
    Is the SPD rating the most important? If the SPD is 1333 is this the memories real speed?
    Most of the memory they do not give the XPD speed but mention it has a XMP profile for overclocking.
    Very confusing. I must admit that in the past I have just purchased the value range when upgrading and have had no idea what I have really purchased.
    The Dominators are out of my price range but all seem to be much higher specked than the vengeance series.
    Is the "Corsair Vengeance CML16GX3M4A1600C9 16GB (4x4GB) DDR3" kit OK for my needs?
    One thing building your own PC, you start to learn a little more and realise the value of forums like these and how little you really know.
    Regards MarkL

  • Z68A-GD65 G3 No video on GPU, IGD works fine

    Hello everyone. I'm making a post on a recent board, mainly the MSI Z68A-GD65 G3, that I've received from a previous RMA due to bad pins. This one boots up normally just fine when plugged into VGA, DVI, and HDMI directly and able to use Windows with no problem. So I use my EVGA GTX 750 that I saved up for the new MB  However, once I try to install my gpu and power it up it doesn't show any sign of post nor boot screen avail. I've updated the bios to the beta from .80 to .93, cleared cmos, and tried installing Intel ME8 afterwards from reading other posts with the same issues. Yet, after some of the suggestions that I've tried out it still shows a blank screen with no post code nor progress whatsoever. I switched the GPU around to the second PCIe slot and tried out my older GTS 250 ones as well, no dice. Is there anything that I'm doing wrong or any alternative that I can try to make it show?
    Board: MSI Z68A-GD65 G3
    Bios: Version: 25.93B
    VGA: EVGA GTX 750
    PSU: Corsair TX850W
    CPU: Intel i5 2500 3.30 GHz
    Mem: 8GB 2x4 Kingston PC3-8500 DIMM 1066 MHz DDR3
    HDD: Western Digital 1TB
    CPU Fan: Intel i5-2500 Processor Fan
    OS: Windows 7 x64 Ultimate
    Any help is greatly appreciated. 

    Quote
    GTS 250 also shows a blank screen with no post code?
    Did you attach the PCI-E power cable, and update the vbios?
    PCI-E cables are connected to it since the GTS 250 requires them, but the 750 doesn't. So they do run fine when I tested them out once more on my old EVGA motherboard. Not sure how to update the vbios, but that sounds like a good idea to give it a shot.
    Quote
    Id this the first time you try VGA card in it since it was RMAd?
    If it is I suggest you take it back with them.
    Well the GTX 750 was recently bought brand new and I tested it out on my previous motherboard along with a friends system as well. It showed up properly with no problem. The z68a motherboard was the one I had to RMA because of broken pins on the CPU slot that gave me an infinite boot loop. Even when plugged into the system and using the onboard graphics, it seems that the board doesn't even detect it in the device manager. I do see 'Unknown Device' in it, but it doesn't exactly tell if its for the VGA card or something else.

  • Z68A-GD65 (G3) not always finding ocz vertex 3

    Me and a friend just bought identical setups, among them was the Z68A-GD65 (G3) motherboard and OCZ Vertex 3 120GB SSD. Both of us get some random crashes and sometimes when trying to boot the computer the SSD does not show up in BIOS (therefore can't boot from SSD). This also happens after a random crash. This usually gets temporarily fixed if you do a hard reboot. However it is very annoying when the computer freezes randomly (can be days between freezes). When BIOS cant' find the SSD it takes a longer time to show the mobo splash screen thingy.
    It is noteworthy that when doing a "hard reboot" it sometimes takes the computer about 5 seconds to startup after pressing the power button.
    Anyone got an idea how to fix this?
    I don't really know how i would go about solving this as it works most of the time so i don't want to fiddle with things i don't completely understand.
    System spec:
    CPU: i7 2600K, 3.4GHz
    Motherboard: MSI Z68A-GD65 (G3), v 23.1
    RAM: 4xCorsair Vengeance Low Profile 4GB DDR3 PC-12800 1600MHz (16GB total)
    GPU: Sapphire HD6950 1GB
    SSD: OCZ Vertex 3 120GB
    OS: Windows 7 Ultimate
    PSU: 650W Corsair

    Quote from: Henry on 17-October-11, 06:59:47
    Check with OCZ for the latest firmware update and see it that fixes your problem.
    Had to install Linux for that and had alot of trouble, but after some hours i finally updated the firmware.
    We will see if it ever happens again.

  • MSI Z68A-GD65 (G3) 99.8MHz bug, temporary fix to make it 100MHz

    With the current available official and beta bios, when disabling spread spectrum, the bus speed does not increase from 99.8MHz to 100MHz, I have messaged MSI support again to look into this with the current 23.4B4 Beta Bios.
    Anyway I have found a fix for this, download the latest Control Center v2.2.0036 off the MSI website.
    If your CPU Base Frequency is at default in bios 10000 you will see 98.8MHz on CPU-Z so in Control Center change the Base Clock (MHz) to 100.2 MHz and click save.
    If your CPU Base Frequency is at 10010 you will see 100.2MHz on CPU-Z so in Control Center change the Base Clock (MHz) to 100MHz and click save.
    Either way when you reboot it will always show 100MHz.  

    Quote from: Nelly. on 06-November-11, 07:41:53
    With the current available official and beta bios, when disabling spread spectrum, the bus speed does not increase from 99.8MHz to 100MHz, I have messaged MSI support again to look into this with the current 23.4B4 Beta Bios.
    Anyway I have found a fix for this, download the latest Control Center v2.2.0036 off the MSI website.
    If your CPU Base Frequency is at default in bios 10000 you will see 98.8MHz on CPU-Z so in Control Center change the Base Clock (MHz) to 100.2 MHz and click save.
    If your CPU Base Frequency is at 10010 you will see 100.2MHz on CPU-Z so in Control Center change the Base Clock (MHz) to 100MHz and click save.
    Either way when you reboot it will always show 100MHz.  
    Thanks for posting this, and creating the thread, Nelly
     I just use the 10010 bclk bios setting, but that band-aid solution doesn't net an even 100.0MHz.
    My earlier attempts at contacting support about the 98.8 issue just get the generic "disable spread spectrum" reply. Some of the earlier bios for my previous MSI P67-G43 board gave me the correct 100MHz bus speed for that board, but it also changed to 98.8 with the later bios releases.
     But even the "first" "00" bios for the Z68A-GD65 G3 has the 98.8 flaw, as does every single bios that MSI has issued for this board, beta or otherwise, since.
    Quote from: HU16E on 12-November-11, 16:02:06
    Granted you might get away with it. But the next person that reads this & uses that for everyday may not be so lucky. If games, applications, programs, & whatever else can't be done on what 1.400v's can provide for a decent performance level, the rest is just for show. That 'is not' a low low voltage for a 4.8. One of the test rigs here & a 2600k will do 4.8 on only 1.392v's with 4 cores & 8 threads & never miss a beat. If really serious about everyday maximum performance on 'real' low low voltage, get a 2700k!
    Rather impressive voltage for 4.9 with that 2700K
    It takes 1.390v. in the bios for my 2500K to do a 12hr. P95 run with no errors, at a much lower 4.6GHz.

Maybe you are looking for