Z68MA-ED55 setting for IGP

Hi, i have a problem with the IGP of i5 2500k. (sandy bridge video driver is installed)
If i set igp as primary boot and use a discrete video card (dvi cable connect to MB) windows boot but i'm unable to go into bios.
If i uninstall the discrete video card the MB don't boot.
Now i can boot windows but unable to go into bios. the monitor does not wake up until windows is load.
After the CMOS reset, which bios setting i must use to work with IGP and no discrete card installed?
Best regards

Quote from: HU16E on 08-October-11, 02:34:12
Try another power cord removed from the PSU, 'battery removed' CMOS clear. If your date & time still shows up as normal after a regular CMOS clear, then it was not a full clear. I have found on several mainboards, both X58 & 6 series chipset boards, that the battery needs to be removed for a full CMOS clearing. Your not alone on this blank screen behavior from startup directly to Windows. I'm working on it as we speak to try & come up with a fix. I have a feeling it will require a battery removed CMOS clearing.
Added: Yup! Theory confirmed! Battery removed CMOS clear works! No more bypass of UEFI/BIOS!
Yep, it works! tnx

Similar Messages

  • Dual monitor output for Z68MA-ED55 (B3) with IGP ?

    Does Z68MA-ED55 (B3) board support dual or multi monitor output with IGP aka built-in intel HD 2000/3000 ( not with discrete graphic card ) like the  H67 boards ?

    By right it should, however, to confirm the answer, it is best to >>contact MSI<<.

  • Intel driver needed for overclocking the Z68MA-ED55?

    Purchased the Z68MA-ED55 a few days ago and loaded most of the software off the accompanying disk.  Through LiveUpdate I was invited to download the latest version of Control Center.  After downloading and launching Control Center, I received a pop-up stating "Please install Intel ME driver for CPU over-clocking".
    Attempting to download the Intel ME Driver from Intel itself I get a message saying the system is not eligible.  Cannot find the driver directly from MSI.
    *NOTE* I am able to overclock through BIOS, it's just not as efficient as Control Center would be.

    Thanks for the assistance.  Once I went back to it I realized I tried to install it before and received a message that there was a newer version already installed on the computer.  Installed the older version and it now works.  Seems Control Center has not been updated to work with the newest ME version yet.

  • Z68MA-ED55 (B3) SSD Caching - hard-drive noise

    I have MSI Z68MA-ED55 (B3) with three hard-drives
      (1) Intel 320 Series SSD 40 GB
      (2) Intel 320 Series SSD 120 GB
      (3) Seagate Barracuda 1TB .  
    I use the 120 SSD for Windows 7 and programs.  I use the Seagate for storage and games and the 40GB SSD to accelerate the Seagate in Maximized mode (for performance: write to SSD first, and delayed writing to spin disk).  This set up is about a week old.  
    I have noticed that the hard-drive makes a clicking noise, very audible, a couple times per 10 minutes.  I suspect that the Z68 SSD caching might doing this.  When I turn off the SSD caching via the Intel Rapid Storage Technology program, the Seagate went 'crazy'  and was clicking every other second for about 1 to 2 minutes while it is unloading the cache.  I have turned SSD caching back on, so far no clicking.
    I am concerned about the noise if it comes back.  Anyone have experienced this?

    To me, it sounds like a bad disk drive. I would swap out the Seagate before fussing with the SSD.

  • MATX MSI Z68MA-ED55

    Here is another motherboard model from MSI using the latest Intel Chipset Z68. It's a micro-atx motherboard but packed with features like - Instant OC, Click Bios, U3/S6, Winki3, Super Charger and OC Genie II.
    Layout of the board is pretty good. Chipset heatsink hold by screws, two video card slots for multi GPU configuration, v-check points which are very useful for overclockers, power / reset easy buttons, military class II components - SFC, Hi-C Caps and Solid Caps, Sata 6GB/s ports which are directly connected to the intel chipset and same goes for the USB 3.0.
    More shots of the board
    Bundled Accessories
    I/O Input Terminals
    •PS2 with auto sense if KB or Mouse
    •USB 2.0 and 3.0 ports
    •IEEE or Firewire port
    •SPDIF and 6 rear audio ports
    •HDMI, VGA and DVI for display output
    •Gigabit LAN
     That's it. WIll update this post soon

    I have installed my MSI Z68MA-ED55 and i was trying to play around with Virtu but it strange i cant add games to the list it's like i am using an "evaluation" version (according to Virtu PDF u cant add game on evaluation version)
    but it's not the only strange thing it visualize with same strange grey area
    those are where i point the area are strangely grey when in the pdf they dont look like that
    and here i cant click on ADD
    I installed the Lucid Virtu downloaded from MSI site ver 1.1.101.16618
    and i tryed to download the one on Intel site as well (same version) and gave me the same result
    there is something to do that i miss why my Virtu is in evaluation or what else is wrong?

  • Z68MA-ED55 (B3) - Realtek HD Audio over HDMI

    Does anyone know if the motherboard Z68MA-ED55 (B3) is able to get HD Audio out from the HDMI connection?
    When I installed the Realtek HD codec I only see listed two digital outs:   optical and atapi.  (which I don't know what atapi is for)
    I think my motherboard need bios updates as mine is in version A1, and the latest A4 seems to fix some audio tables (which I don't know what it means neither..
    Anyone has HD audio over HDMI for this board or advice about what to try?
    thanks
    Update:
    Seems my board should support HDMI HD Audio out..
    From MSI board document:
    Chip integrated by Realtek® ALC892
    Download the manual at:   http://www.msi.com/product/mb/Z68MA-ED55--B3-.html#?div=Manual
    From Realtek ALC892:
    The ALC892 also features secondary SPDIF-OUT output and converter to transport digital audio output to a High Definition Media Interface (HDMI) transmitter.
    Documentation at:  http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PNid=24&PFid=28&Level=5&Conn=4&ProdID=284

    Any luck getting HD audio to work over HDMI?

  • MSI Z68MA-ED55 B3 + Cooler Master V8 CPU Cooler Compatibility

    Guys, Anyone please advise if Cooler Master V8 CPU Cooler is compatible to Z68MA-ED55 motherboard. What i exactly mean is that will it fit without me having to move the RAM to other slots? Thanks guys!

    Depends on the RAM. If you intend to get flashy RAM modules that have heatspreaders (useless for all practical purposes) as high as mountains, then you have a problem. If you stick to JEDEC standard modules, i.e. black chips on green sticks, or Low profile modules, then these should fit just nicely.
    Suggest you read the technical design document of the cooler and check what the clearance is from the heatsink upwards to where the cooling fins start. Check the technical design specs of your intended mem modules and see what the height is. That should give you a good indication.
    If you want an excellent cooler that has plenty clearance by design, consider the Zalman 9900 series.

  • Z68ma-ed55 be keeps power cycling

     
    Have the z68ma-ed55 with a Intel I7-2600K LGA 1155 CPU and 8 GB ram and when i power it up the MB stays on for 10 seconds and then powers down again.
    If i pull one stick of the memory the unit powers up and starts beeping... what am i missing here?
    ■Intel I7-2600K LGA 1155
    ■DDR# 1600 Hperx T1 2x4 gb module total of 8GB memory

    Suspect an incompatibility with the RAM or even the possibility of a CPU socket pin problem. Do you have a single stick of standard DDR3 1333 chipped 9 9 9 xx 1.50v. + or - 0.75v. RAM you can try? Possibly a relative, friend, or co-worker has one you can try with?
    Added: Not normal procedure, but you might try a single stick in each RAM slot & check for POST. Also, have you tried a power cord removed from the PSU, battery removed for awhile, CMOS clear?
    2nd add: What is the UEFI/BIOS version listed on the green sticker on the mainboards BIOS chip?

  • MSI Z68MA-ED55, or Z68 series, support XEON E3 series processor?

    Hello,
    does anyone know if the MSI Z68MA-ED55, or any other Z68 series, motherboard supports Intel XEON E3 series, like the E3-1275?
    Cheers

    You should look through the product information in MSI website first. If the board supports, then the processor will be listed under their support listings, else it's a no. For more information on any other supporting processors, please contact MSI as per the link given by HU16E.

  • Using a Variable in SSIS - Error - "Command text was not set for the command object.".

    Hi All,
    I am using a OLE DB Source in my dataflow component and want to select SQL Query from the master table  I have created variables v_Archivequery
    String packageLevel (to store the query).
    <Variable Name="V_Archivequery" DataType="String">
         SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
         FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
         ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
         Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)
        </Variable>
    I am assigning this query to the v_Archivequery variable, "SELECT a.*, b.BBxKey as Archive_BBxKey, b.RowChecksum as Archive_RowChecksum
    FROM dbo.ImportBBxFbcci a LEFT OUTER JOIN Archive.dbo.ArchiveBBxFbcci b
     ON (SUBSTRING(a.Col001,1,4) + SUBSTRING(a.Col002,1,10)) = b.BBxKey
    Where (b.LatestVersion = 1 OR b.LatestVersion IS NULL)"
    Now in the OLE Db source, I have selected as Sql Command from Variable, and I am getting the variable, v_Archivequery .
    But when I am generating the package and when running I am getting bewlo errror
     Error at Data Flow Task [OLE DB Source [1]]: An OLE DB error has occurred. Error code: 0x80040E0C.
    An OLE DB record is available.  Source: "Microsoft SQL Native Client"  Hresult: 0x80040E0C  Description: "Command text was not set for the command object.".
    Can Someone guide me whr am going wrong?
    Please let me know where am going wrong?
    Thanks in advance.
    Thankx & regards, Vipin jha MCP

    What happens if you hit Preview button in OLE DB Source Editor? Also you can use the same query by selecting SQL Command option and test.
    Could you try set the Delay Validation = True at Package and re-run ?
    If set the query in variable expression (not in value), then Set Evaluate As Expression = True.
    -Vaibhav Chaudhari

  • On HP-UX 11g rac cluvfy tool failed with "/dev/async"  (incorrect setting for minor number.)

    Hi ,
    We are planing to upgrade our 10g R2 CRS to 11g R2 CRS on HP-UX server ,while running cluvfy tool we are getting the below error.Please help me to fix this issue.
    Checking settings of device file "/dev/async"
      Node Name     Available                 Comment
      erpdev04      yes                       failed (incorrect setting for minor number.)
      erpdev03      yes                       failed (incorrect setting for minor number.)
    Result: Check for settings of device file "/dev/async" failed.
    Pre-check for cluster services setup was unsuccessful on all the nodes.
    oracle.oracle.erpdev03.fwprod_app1> (/app/oracle/oracle_source/patches/bin)

    # /sbin/mknod /dev/async c 101 0x104

  • Where did all the setting for printing go in PSE8-Mac?!

    OK, I'm probably missing some obvious settings somewhere, please tell me after you read my rantings...
    I'm using the 'Full Edit' mode, assuming that is important. But the new Print Dialog looks like it has been dumbed down for some one, not sure who, however has it has me completely confused. There are now only three 'steps' for printing. One and two are self explanatory. However...
    Step three concerns paper size, image size and several other details. Just for testing, I created a new 4 x 6 inch, 300dpi page and drew some lines. Command-P. Proper printer is selected, select "Letter" as the paper size. 4 x 6 inch appears selected as the "Print size" (I thought that was because of the original page size, but it appears to simply be the default). That is a detail that could easily be over looked by a new user. If the original image is larger than 4 x 6, it will, obviously be either cropped or reduced to fit those dimensions! It seems to me that the "Select Print Size" should automatically assume to be the image size. OTOH, I can see that some people may want to do all their printing on one size of paper. In that case, why not have a preference for the default and let the user change it when they change paper sizes (if they want)?
    Now, if the user happens to notice that a new 8 x 10 inch image is going to be printed in a 4 x 6 area, she will now decide to check the other settings available in the pop up menu. OK, there IS an 8 x 10 inch choice. But look, what's this "Custom" choice? Let's investigate...Now this is strange! The defaults there seem to be 1.383 inches for height AND width! Who came up with that weird number?!
    Oh, there is a "Scale to Fit Media" check box. Checking that now makes the height and width somewhat closer to reality, they now indicate the pape dimensions. That IS logical, but not extremely helpful, IMHO. By the way, the second time one selects the "Custom" choice, the correct, original image size appeared in the Print size boxes. Although I cannot seem to get those to reappear. Oh well...
    My point is, how do these confusing configurations help? Beyond me, anyway.
    BTW, the dpi settings all seem to be 'computed' at one less than the number set by the user for an image. For example, a new image page created at 300 dpi shows 299 in the Custom dialog, 150 shows 149, etc. Close, but why not exact? Furthermore, why can't the user select any dpi they choose? Isn't that what the computer if for; calculate what happens to the pixels when they print at a different setting than the image? Sure, the user should be warned that terrible images my result, but if that's what the user wants, let it be done! Who's running this show, anyway? Oh yeah, I remember, now...excuse me for asking, I'm only a paying customer, what do I know?!
    Lastly, if one has more than one image open, every single one can easily be printed, accidentally. Why? Because they will all appear in the Print Dialog. Don't you see them? Over there on the left. Yeah, I see them, but why doesn't the image I have in front, the one I'm working on, be the one I probably want to print? Many of the others may simply be images I'm borrowing parts from. Why do the developers think I always want to print every image that might be open? I don't have any idea, either. Sure, there are a couple of ways to prevent this multiple image printing; select the one you don't want to print and use the "minus" button or simply close all those images before going to the Print dialog. Guess what. Using the 'minus' button only works for this printing, the next time you ask to print they will all be there, again. And, what if you aren't really finished using some of those extra images that you closed? Now you get to re-open them all again. Completely unnecessary steps because of poor user considerations/research, in my humble opinion. Again, this is exactly the thing that preferences are made for. Or, put them in the "Edit Guided" mode! Or, better yet, just give me back the old Print dialog! Nice!
    Now, I am extremely glad to see that PSE can now remember to keep that stupid Panel bin out of the way! Finally! Three more inches of screen to work with!!! Hooray!! Unfortunately, it still can't remember what the last setting for the jpeg quality was...still defaults to ZERO! Sure, that's the setting I always want to use, it's so much fun letting people try to guess what is in the image...one would think after 8 iterations this could be fixed. One down, umpteen to go. Oh well, what do you want for $80?

    Thanks for your listening/reading and I'll take your advice about dropping a note to the developers, but I won't be holding by breath! I doubt that they consider this a real problem. It's really just my ranting!
    Your solution is probably the 'fix' they might suggest, anyway. However, I'd rather have the screen space than a list of thumbnails of images I already have open. command-plus and/or minus is a pretty quick way of making it easy to see anything that might be visible. Of course, I'm sure there are other uses for the Project Bin that many find useful. Even though I have a 24" iMac, I rather like using the screen space the way I want, not an arbitrary way that got developed. I just don't see why developers can't program an app to allow every conceivable method of use by every living and future user! LOL!!!
    I guess today was the first time I've printed anything since installing 8. I was, quite confused when presented with the new Print interface. Actually, I thought that must be part of the 'Guided' set up which I assume leads one by the hand as much as possible. "Thank you Adobe, but I'm trying to avoid unnecessary contact with strangers right now." LOL! At least I know I didn't miss some setting somewhere.
    Thanks! Have a great weekend! And don't get scared too much tonight!

  • I can't save the setting for dowloads to go to the specified folder (such as the desktop). It restores to default when I close Forefox.

    I can't save the setting for downloads to go to the specified folder (such as the desktop). It works once but it restores to default next time I open Firefox.
    == This happened ==
    Every time Firefox opened

    Make sure that you not run Firefox in [[Private Browsing]] mode.
    In Private Browsing mode some menu items are disabled (grayed) and some features like visited links and others are disabled and not working.
    You are in Private Browsing mode if you see "Tools > Stop Private Browsing".
    See [[Private Browsing]] and http://kb.mozillazine.org/Issues_related_to_Private_Browsing
    See also http://kb.mozillazine.org/Preferences_not_saved and [[Preferences are not saved]]

  • How to create a value sets for concurrent program?

    Hi Friends,
    I am creating a concurrent program with a parameter period...
    In the value set for the parameter period, I am using the following query :
    ---where application_id = 101
    and set_of_books_id = :$PROFILES$.gl_set_of_bks_id
    and closing_status IN ( 'O', 'F', 'C')
    order by period_year, period_num' ----
    In my cursor, i have a condition 'where set_of_books_id = ' ---
    How can I pass the above set of books id into the cursor ?? it is not working when I am defining another parameter as Book and passing that value to the cursor....
    I need that period parameter to return all the periods for the set of books where we are running the concurrent request from...I also need to get the set of books id for my cursor...
    Hope I am making sense...All that I am trying is to have period parameter and also a SOB id in cursor condition...
    Rgds,

    Hi Vamsi /Nitin,
    Let me explain the whole thing now.....
    My plsql procedure is ......
    CREATE OR REPLACE procedure GL_INT(
         perrbuff     out varchar2,
         pretcode     out varchar2,
    pbook          in varchar2,
    pperiod          in varchar2
         ) is
    cursor cur1 (p_sdate in date, p_edate in date )is
    select distinct group_id groupid,
    user_je_source_name source
    from gl_interface
         where accounting_date >= p_sdate
    and accounting_date <= p_edate
    and set_of_books_id = pbook;
    cursor cur2 is
    select distinct start_date sdate,
         end_date edate, period_name period
    from gl_period_statuses
    where      period_name = pperiod
         and set_of_books_id = pbook
         and application_id = 101;
    i               cur1%rowtype;
    j               cur2%rowtype;
    begin
    open cur2;
                   fnd_file.put_line(fnd_file.output,'PERIOD'||'----'||'GROUPID'||
                                       '----'|| 'SOURCE');
              loop
                   fetch cur2 into J;
    exit when cur2%notfound;
                   open cur1(J.sdate,J.edate);
                   loop
              fetch cur1 into I;
                        exit when cur1%notfound;
              fnd_file.put_line(fnd_file.output, J.period||'----'||I.groupid||'----'||
                                  I.source);
                   end loop;
              end loop;
         Close cur1;
    close cur2;
    Exception when others then dbms_output.put_line(SQLERRM);     
    end;
    ==================================================================================================
    For SOB value set, I have passed the default value as vamsi suggested ($profiles$.gl_set_of_bks_id)....
    For period value set, I have entered query as ..where application_id = 101
    and set_of_books_id = :$PROFILES$.gl_set_of_bks_id
    and closing_status IN ( 'O', 'F', 'C')
    order by period_year, period_num...................
    It still doesn't work....I don't know how to derive those Periods based on the SOBs and at the same time pass SOB id into the cursors...
    Please help...
    Rgds,
    Murali

  • Best setting for gif animations

    what is the optimal setting for animated gifs

    Depends on your style and your training as an animator, and
    what your project goals are: straight animation? interactivity?
    e-cards? Traditional animators used to drawing frame-by-frame with
    exposure sheets will feel more comfortable with Toon Boom Studio
    (www.toonboom.com). It has far superior drawing tools and color
    pallette management and timeline management than Flash. But if
    you're used to Illustrator, that may make no difference to you. It
    appears that the upcoming Flash CS4 will narrow the gap, as the
    interface appears to include enhancements that will be more
    familiar to traditional animators, not to mention IK, which Toon
    Boom Studio doesn't have (the highly expensive Toon Boom Solo does
    have it).
    That said, I think Flash is a great program for creating
    cartoon animation. You may not think you're interested in
    ActionScript programming at this point. I use Flash mainly for
    cartoon animation and I resisted ActionScript for a few years. But
    once you get used to Flash as an animation tool, and then decide to
    dip your little toe into ActionScript, you'll find out what an
    astounding tool it is, even for traditional animation, enabling you
    to do things impossible in more traditional-oriented programs. Plus
    now Flash and Illustrator are fairly well integrated, so you'll be
    able to import and export between the two.
    On balance, I'd go for Flash.

Maybe you are looking for