Z77 gd65 gaming slow hdd transfer rate plz help

my specification
1. intel g2020 2.9ghz
2. ram 8gb patriot ddr3 1600 set in bios
3. motherboard z77 gd 65 gaming and non gaming
4. 8 hdisk sata 3 each 3tb wdc green ezrx
5. psu seasonic x760watt gold
6. win 7 64bit
bios setting
sata set to ahci
eksternal sata set to ahci
problem is
before i clean install my pc , one of my hdd died.
my transfer rate beetween internal hdd is very good, iam using teracopy 2.3
speed is 80-100mb/s.
transfer speed from internal hdd to eksternal hdd (wdc mybook usb 3) also good 70-90mb/s
but now after clean install windows 7 64bit
teracopy speed down to 40-50mb/s
nothing changed from hardware but the copy speed is very low now
bios setting still like the same all sata set to ahci
all driver in device manager is installed
i have tried 3 times clean install win7 hope to get back the normal copy speed but nothing changed iam stuck at max 56mb/s
plz someone who ever experience or know the solution help me
thank you very much before

Hi,
Have you installed ALL the drivers before you made any tests?
You might also want to Clear the BIOS (Copied from Troubleshooting Guide V1.0 as I couldn't find the link for just clearing the Bios):
Quote
Clearing the CMOS chip
Disconnect the system power cord and push the case power button to drain all remaining power in the psu for approximately 15 seconds
Then move jumper jbat1 and wait 10 seconds and move it back to the original position. You should ensure that the jumper has metal inside of it when removed, sometimes (rarely) they don't. This process resets or clears the CMOS chip and is shown in most motherboard manuals.Now connect the power cord and restart your system.
Some motherboards require that the battery must be removed for 20 minutes before putting the battery and jbat1 back for the CMOS chip to be cleared.

Similar Messages

KT3 Ultra ARU Slow HD Transfer Rates

Hello,
First, please see my system information at the bottom of this message.
I have a MSI KT3 Ultra ARU motherboard and have installed a Maxtor ATA133 60GB hard drive with 2 MB cache. The hard drive is jumpered as Master and is connected all by itself on the IDE1 ribbon cable. On IDE2 I have a CDRW (Master) and a CD-ROM (Slave). My other hard drive (WD 120GB ATA100 8 MB cache) is on IDE3 and is set up in RAID 1+0 stripe.
I recently ran the Sandra file system benchmark on my hard drives with what I think are very discouraging results. My Maxtor drive on IDE1 scored 32 MB/s and my WD drive on IDE3 came in at 23 MB/s. Those are some stinky results aren’t they?
I checked my Device Manager under IDE ATA/ATAPI Controllers and it indicates that for my Primary IDE Channel the current transfer mode for device 0 is Ultra DMA Mode 6. I don’t know how to check the transfer mode on my IDE3 hard drive.
Question #1: Are my 32 MB/s and 23 MB/s results slow for my hardware?
Question #2: If these results are slow, how can I increase the transfer rates?
Please help!
Thank you!!!!
My System
AMD Athlon XP 3000+
MSI KT3 Ultra ARU MOBO
2 x 256MB DDR PC2700 SDRAM
ATI Radeon 9600XT 256MB
Western Digital WD1200JB 120GB Caviar HD ATA100 8MB Cache 1+0 Stripe/RAID0
Maxtor 6Y060L0 60GB HD ATA133
Pioneer DR-A04S CD-ROM 32X
Lite-On LTR-48125W 48x12x48 CDRW
TTGI TT-350SS (350W) Power Supply
PSU Ratings: +3.3V/28A +5V/35A +12V/16A
Windows XP Home SP2

These tranfer rates seem fine for sequential read rates. The maxtor drive is at mode 6 and the WD should be at mode 5 if its ATA100.

FTP/SFTP/FISH (etc) slow file transfer rate over LAN

Hi everyone,
I have a problem with transferring files over my home network that has been bothering me for quite some time.
I have a 802.11n router which should provide me with the transfer rate up to 150 Mbps (afaik). When I download files from the Internet, 3 MB/s data transfer rate is of no problem.
However, when receiving or sending data over LAN, the transfer rate is much slower (1.8 MB/s).
My rough guess is (after reading some papers on this topic) that TCP protocol is causing this (its flow control feature to be exact), since TCP max window size is too small on Linux by default.
So, setting TCP max window size to a greater number should solve this.
I tried putting this:
# increase TCP max buffer size setable using setsockopt()
# 16 MB with a few parallel streams is recommended for most 10G paths
# 32 MB might be needed for some very long end-to-end 10G or 40G paths
net.core.rmem_max = 16777216
net.core.wmem_max = 16777216
# increase Linux autotuning TCP buffer limits
# min, default, and max number of bytes to use
# (only change the 3rd value, and make it 16 MB or more)
net.ipv4.tcp_rmem = 4096 87380 16777216
net.ipv4.tcp_wmem = 4096 65536 16777216
# recommended to increase this for 10G NICS
net.core.netdev_max_backlog = 30000
# these should be the default, but just to be sure
net.ipv4.tcp_timestamps = 1
net.ipv4.tcp_sack = 1
in /etc/sysctl.conf but to no avail.
So either there is no problem with the max window size setting, or the Linux kernel ignores it (maybe because /proc is no longer supported?).
Thanks for any neat ideas.
Last edited by Vena (2012-06-01 21:48:14)

Bump? No ideas whatsoever?

Incredibly slow firewire transfer rate

Hi fellas
my firewire drive (formatted ext3) has an incredibly slow 2MB/s transfer rate?
Is this normal? Anything I can do about it?
Cippa Lippa

I have a FireWire 400 HD, it has a JMicron chipset (pretty generic but works great). I worked wonderfully on Leopard without a single glitch ever.
Now, after upgrading to SL, I experience the same as you and the drive is not responding well, hanging constantly and experiencing really slow transfer rates, that make it unusable (all applications that try to open something from it eventually hang). It's not a temporary glitch, even after several reboots and connecting/disconnecting the drive. The same drive under USB2 (it also has USB2 interface) works perfect (but I really want my firewire back).
I hope Apple fixes it! Definitely a bug.

MSI Z87 GD65 GAMING Doesn't recognize crossfire. Help Pls.

Hello everyone, I've had several board msi brand, such as B3 P68 GD65, GD65 G3 Z68, Z68 GD80 G3, last week bought a Z87 GD65 gaming, but I can not activate the second video card, installed the amd 13.9 drivers with just one card ,rebooted and installed the second does not recognize the second card. I tested amd drivers 13.10v2 and does not work, I tested with the older amd drivers 13.4 official and does not recognize the second card.
Tested one by one each both graphical works fine.
I have the crossfire bridge connected.
I must change something in the bios? To recognize the second card? what ?
Never happened to me on msi boards such things and i haved always crossfire.
Sistem :
Caixa Fractal Arc mid R2
psu Corsair tx 650 modelar
Rams Corsair vengeance 16Gb 4x4 1600 mhz.
Coller Corsair H100 I
hard drivers Adata Sp 9000 64 GB sata 6Gb para o SO
kingston V300 64 GB sata 6Gb para jogos.
Western Digital blue 1 TB sata III 64 MB
Board MSI Z87 Gd65 Gaming
Cpu Intel 4770k
Cards 2 vtx hd 7870 x-edition oc Gpu clock : 1100 Mhz, memory 4900 Mhz.
Greetings from Portugal!

Hi everybody,
I tested one at a time in the pci-e 2 and works.
And do the same on Pci-e nº1. works fine the 2 card.
"Several possibles. If testing a card by itself in the second slot does not work, then either there is a problem with an errant standoff or other item shorting underneath the mainboard. The other most common reason is CPU socket pin(s) bent or damaged or the CPU cooler mouinted incorrectly or unevenly torqued.
I don´t believe it the pins because if you look at the GPU-Z recognizes the two cards.
And appears on device manager the to cards.
I am using SO w7 ultimate, and the board bios is the last version.
Is something else must be some setting in bios, and i don´t no...
http://imageshack.us/photo/my-images/34/lnow.jpg/
Best regards.

Flashing of MSI Z87-GD65 GAMING failed and dual bios not helping, not sure why?

Hi all
For the first time in 20 years Ive had a firmware flash fail it seems.
I have a MSI Z87-GD65 GAMING and updated the bios with the latest firmware via the "M-FLASH" utility within the systems bios.
All seemed to have gone well, it flashed to 100% rebooted and then just a blank screen and a sequence of keyboard light flashes.
After a minutes panic I thought not to worry, the motherboard has a dual bios. So I powered down and switched the bios switch to bios B hoping it would assist and the problem is identical.
Any tips anyone?

I just tried this along with removing power from the main board and it seems one of the two did it! thanks

Slow itunes transfer rate to ipod

Just upgraded my desktop to IOS 7, as sson as I installed itunes and tried to transfer a tv episode it went stupidly slow (normally in seconds). Connected my ipod to my daughters laptop (also upgraded recently) and same tv episode went on in seconds.
Have reinstalled itunes on my desktop numerous times and tried all the tips on the net.
I'm thinkng it has to be my desktop but I dont know why?
Please help its doing my head in.

If you did not remove and reinstall all Apple software then do:
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

Slow data transfer rates

I have a MacBook Pro - Retina with an Apple thunderbolt to gigabit ethernet adaptor which is connected directly to one port of a synology 412+Nas with Cat6 cable. I am experiencing low data rates when transferring large files (>1GB) usually less than 25Mb/s though sometimes peaking at 100Mb ( fora few seconds) The average rate declines throughout the file transfer. I have noticed that there is a repeated/ self recovering crash which occurs which is co incdent with a dip in the date rates. Having eventually found the crash report its detail is associated with Finder. I am not technically savy enough to interpet the report nor have I been fortunate enough to find the crash reports again!
Has anyone else had this data rate performance issue?

your profile will sort itself out after that period but if you are having disconnection with the hub resetting then there is a more serious noise problem. Check your phone line by dialling 17070 option 2 - should hear nothing - best done with a corded phone
Are you connected to the master or test socket or somewhere else? do you have extensions sockets and if so have you removed the orange bellwire from terminal 3 from the master and all the extensions as this can act like an aerial for noise. http://www.jarviser.co.uk/jarviser/bellwirenutshell.html
there is no point in getting the mods to fix your profile if you have a noise problem as you will be back to square 1 in a few days so better sorting problem first
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Slow Data Transfer rate in 5230

Hi All,
I am using Nokia 5230 with BSNL 3G sim, I am connecting using data cable through PCsuit. With the Full Signal also I am getting a maximum speed of downloading as 40-50 KBPS which is not desired at least it must give 100 KBPS, what the setting I need to do to make it more faster.
Thanks you

Can i contact u----------- i need ur help for conecting my phone 2730c to mobilenet---
my email address is .
pls,pls,pls contact meeeee...
Thanking you - K.Prakash
Moderator Note: E-mail address removed. It is unwise to publish personal contact information on a public web forum.

Mp3 format, still cannot transfer! Plz help!

Hi,
I am trying to transfer a file to my iPod. It says it is an mp3 format sound, the file can be played on iTunes, but when i try to transfer it, there is an error saying that "the song cannot be played on this iPod. What do i do?
Plz someone help.. Thanks

I just had this problem as well and spent quite a bit of time reviewing all of the suggestions/ideas/comments, and since I am not that tech-savy I remembered this "suggestion" from the UK show The "IT Crowd" which was "Have you tried turning it off and on again??" (both devices)
http://bit.ly/18qL7OA (apologies for short ad on the youtube clip)
It worked!!

Macbook is suddenly slow (detailed report included) plz help!

i dont download a whole lot of things on it except for music.. over the past few days its been slow. The colorwheel pops up almos all the time now. I would appriciate any help. Thanks
Hardware Information:
          MacBook Pro (13-inch, Early 2011)
          MacBook Pro - model: MacBookPro8,1
          1 2.3 GHz Intel Core i5 CPU: 2 cores
          4 GB RAM
Video Information:
          Intel HD Graphics 3000 - VRAM: 384 MB
System Software:
          Mac OS X 10.7.5 (11G63b) - Uptime: 0 days 6:7:43
Disk Information:
          Hitachi HTS545032B9A302 disk0 : (320.07 GB)
                    disk0s1 (disk0s1) <not mounted>: 209.7 MB
                    Macintosh HD (disk0s2) / [Startup]: 319.21 GB (227.24 GB free)
                    Recovery HD (disk0s3) <not mounted>: 650 MB
          MATSHITADVD-R   UJ-8A8
USB Information:
          Apple Inc. Apple Internal Keyboard / Trackpad
          Apple Inc. BRCM2070 Hub
                    Apple Inc. Bluetooth USB Host Controller
          Apple Inc. FaceTime HD Camera (Built-in)
          Apple Computer, Inc. IR Receiver
FireWire Information:
Thunderbolt Information:
          Apple, Inc. MacBook Pro
Launch Daemons:
          [System] com.adobe.fpsaud.plist 3rd-Party support link
          [System] com.oracle.java.Helper-Tool.plist 3rd-Party support link
Launch Agents:
          [System] com.oracle.java.Java-Updater.plist 3rd-Party support link
User Launch Agents:
          [not loaded] com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist
User Login Items:
          iTunesHelper
Internet Plug-ins:
          Silverlight: Version: 5.1.10411.0 - SDK 10.6 3rd-Party support link
          FlashPlayer-10.6: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
          Flash Player: Version: 12.0.0.77 - SDK 10.6 3rd-Party support link
          QuickTime Plugin: Version: 7.7.1
          JavaAppletPlugin: Version: Java 7 Update 25 Outdated! Update
Audio Plug-ins:
          iSightAudio: Version: 7.7.1 - SDK 10.7
iTunes Plug-ins:
          Quartz Composer Visualizer: Version: 1.3 - SDK 10.7
User iTunes Plug-ins:
          AudioScrobbler: Version: 6.0.5 - SDK 10.8 3rd-Party support link
3rd Party Preference Panes:
          Flash Player 3rd-Party support link
          Java 3rd-Party support link
Old Applications:
          None
Time Machine:
          Time Machine not configured!
Top Processes by CPU:
               3%          WindowServer
               2%          EtreCheck
               2%          Last.fm Scrobbler
               2%          iTunes
               1%          coreaudiod
Top Processes by Memory:
          860 MB          Safari
          348 MB          WebProcess
          131 MB          iTunes
          61 MB          Last.fm Scrobbler
          57 MB          WindowServer
Virtual Memory Information:
          836 MB          Free RAM
          1.66 GB          Active RAM
          713 MB          Inactive RAM
          851 MB          Wired RAM
          420 MB          Page-ins
          718 MB          Page-outs

That's got to be the cleanest report I've seen, so I have nothing to offer from the report to help with your Beachball issue. Suggest you check a few of these ideas: Macintosh OS X Beachballs!
However I do have a few update recommendations:
Java is seriously out-of-date, so I hope you don't have it enabled in your browsers. To update to Java Update 51 open System Preferences and click on Java to open the Java Control Panel. Choose the Update tab and follow the instructions there or download from Java.com.
Silverlight from Microsoft has some sort of security issue (probably Windows) and should be updated from Microsoft.
You don't need "com.apple.CSConfigDotMacCert-[...]@me.com-SharedServices.Agent.plist" since MobileMe was discontinued. To find it hold the option key down and select "Library" from the Finder's Go menu. Now look in the LaunchAgents directory (folder), find that file and drag it to the trash. This should not be causing you any issues whatsoever, you just don't need it any more.
Your hard drive will fail sooner or later (average life about 3 years) and probably quickly, so you need to have a current backup. If you don't like Time Machine for some reason, then make certain you have an alternative backup system in place.
Lex usually comes on a bit later, so he may have some other ideas for you.

Slow Data Transfer on Server 2012 R2 Essentials - Can't Disable SMB Signing

I've seen several solve their slow file transfer rates by disabling SMB signing (that is, workstations connected to the server can move files from folder to folder, but it takes forever, whereas if one is logged onto the server through a third-party client
(like TightVNC), one can easily move files from folder to folder--no delay).
I thought I'd do the same as one of my clients is suffering this problem.
Unfortunately, the necessary items ("Microsoft network server: Digitally sign communications (always)" and "Domain member: Digitally encrypt or sign secure channel data (always)") are greyed out and I can't disable them. I'm logged in
under the administrator account.
Is there another work around?

Hi MarKomus,
à
Unfortunately, the necessary items ("Microsoft network server: Digitally sign communications (always)" and "Domain member: Digitally encrypt or sign secure
channel data (always)") are greyed out and I can't disable them. I'm logged in under the administrator account.
Based on your description, I understand that you want to configure those two group policy settings in client
computer, and then find that they were greyed out and can't be disable.
Just addition, please logon your Windows Server 2012 R2 Essentials via Administrator account. Then open Group
Policy Management Editor and follow the path: Computer Configuration-> Policies-> Windows Settings-> Security Settings-> Local Policies-> Security Options, then please check if that two policy settings had been defined and configured in the
DC.
If anything I misunderstand or any update, please feel free to let us know.
Hope this helps.
Best regards,
Justin Gu

Overclocking Z77a GD65 Gaming Motherboard

Hello everyone, I am new to the forums, and new to overclocking MSI boards.
I am trying to overclock my new Z77 GD65 Gaming mb but cant get a stable clock. I prefer to do it manually instead of using the OC genie, but can't find any guides on it.
I am coming from EVGA boards, so to do things like disable turbo, and not disable vDroop are pretty new to me as well.
On the EVGA Z77 FTW, I have gotten a stable clock of 5.2GHz, but cant even get a clock of 4.5GHz on this board.
Can someone point me out to a guide or give me pointers on how to get a stable OC and get my RAM at 2133MHz?
Thanks in advance.
My setup:
i7 3770K
16GB G.Skill Sniper 2133MHz 1.65v
Custom Loop
240GB Corsair Neutron GTX
120GB Corsair Neutron GTX
2x 60GB Corsair Force GT (raid 0)
2x EVGA GTX 780 SLI

Quote from: Bernhard on 11-October-13, 18:50:27
Have a look in this thread for a start. https://forum-en.msi.com/index.php?topic=159647
I saw that thread, but was unsure about the templates. They seemed to be default values. I could be mistaken, but I saw default clocks.

Audio glitches after BIOS update on GD65 Gaming

I updated from the beta 1.94 BIOS to 1.A0 and since then have experienced audio glitches. Streaming videos the audio will fast stutter periodically. My DJ controller also glitches which is a different soundcard entirely. Using DPC Latency tool I see large random spikes every so often which coincides with the audio glitches. I tried LatencyMon and it shows HDAudBus.sys as causing high interrupt to process latency. But if I disable that it then gives the same fo ACPI.sys. If I kill some services and background tasks it would sometimes show the same but for hal.dll or wfd0100.sys (part of Logitech Setpoint I think). I can never seem to nail it down. So I booted into diagnostic startup using msconfig and the spikes more or less went away. So I ended up booting with just the essential network and audio drivers running using msconfig and it seemed to fix it but I cannot be doing that each time I want to use my DJ controller or play a Youtube video.
It did not do this before the BIOS firmware upgrade.
Ideas?
Win7 Ultimate 64 btw.
EDIT: I flashed using LiveUpdate and forgot to do a BIOS reset with power cord disconnected (going to try the latter now now but doubtful it will help). Should I re-flash from USB?

Quote from: Sea Dog on 03-July-14, 01:25:23
There are a good number of GD65 Gaming mainboards, so it would be helpful to know exactly which chipset you have. M-Flash has been reliable with Z87 and Z97, but if that method is used, be sure to select the BIOS + ME option. Install the newest ME driver after a flash.
It's the Z87 Haswell version.
BTW there is a dual BIOS on this board right? Can't I switch to the other BIOS, bootup and test? Never tried the dual BIOS thingi before and wondered about if it's possible to switch between them? EDIT: Just read the manual. Not what I thought it did. Oh well.
EDIT2: I flashed the latest beta 1.10 B3 BIOS using the USB boot method, reset the CMOS by crossing the pins and uninstalled/installed the latest ME driver.
No difference.
If U run LatencyMon 'as is' after reboot and after stuff has settled down it reports random spikes of the HDAudBus.sys well over 1000ms
If I disable HDAudBus.sys in system devices it then spikes with ACPI.sys
If I use a tool like JetBoost to kill some apps and services spikes with usbport.sys or ACPI.sys or HAL.dll or sometimes wfd0100.sys
If I use msconfig to boot into diagnostic mode I don't get any spikes.
If I use msconfig to boot into a mode where only the services required for network and audio to work I also get no spikes (but this is tiresome to use. I wish msconfig had user profiles. I also tried a tool called Startup Selector which promised that functionality but it crashes when I apply the changes).
I can only surmise a MS service (tried just disabling non-MS services with no effect) or combination of MS services is causing this issue.
I'm thinking the next step is an in place upgrade of Win7 and if that does not fix it a complete reinstall (that would really suck). :(

HDD data transfer rate is slow in my new i7

Hi
I had MacBook Pro 15" , 2.8 GHz , 500 GB HDD and because of some hardware problems Apple replace this laptop with new MacBook Pro 15" 2.66 i7 CPU, 500 GB HDD. I install same windows7 64bit in both via Boot camp. Disk transfer rate in old MacBook is 5.9 and in my new laptop is 5.6 ?!?!?!?
I installed Bootcamp drivers and also installed all updates of windows7.
Can you tell me reason of this difference and any solution to improve this rate?

Hi n, and welcome to Apple Discussions.
As you're still covered under warranty, call AppleCare or go to an Apple Store or AASP and explain the situation. A replacement computer is supposed to meet or exceed the machine it replaced, and if yours isn't performing to that level . . . .

Z77 gd65 gaming slow hdd transfer rate plz help

Similar Messages

Maybe you are looking for