Z77 MPower and second RAID not bootable [Mid long, hope clear]

Hi to all,
installed Windows 7 in first RAID "A" (is RAID 0 with SATA connector 0-1) without problem
a next step installed another W7 in second RAID "B"  (is RAID 0 with SATA connector 2-3),
but a first restart during installation of O/S the board/system slips only in RAID "A" 
(try to select corret RAID in BIOS before pressing F11: nothing to do !)
Detached connector SATA 0-1, installation is performed good in the other RAID "B".
Reattached all connector SATA i have no way to select RAID "B", again only boot in RAID "A".
In the settings boot of BIOS the first boot is Intel RAID"A" but not is listed another RAID
(second USB, third CD, etc...), in  the boot hard disk sequence is RAID "A" and next RAID "B".
Now all O/S is installed good but on press F11 and select a second RAID "B" " for boot in to it,  the system/board load
only RAID "A",  i am not able to go  a second RAID "B" (need detach the connector of other RAID)
Were is my wrog settting ? 
   

Quote from: Caronte on 23-February-13, 04:33:37
Hi xmad
First: ty for your availabilty.
For second, asking you (hope dont tired you or got OT):
i have  raised a second RIAD and installed the second O/S on
simply volume, now the F11 choice is ready to job.
For my knowledge why this is possible when RAID with RAID dont is it ?
Neither one is gauanteed to work. I contacted MSI about this one, and they said that even if it does work there may be irratic behavior. It just wasn't designed to do this.

Similar Messages

  • IPhone 5 getting really hot and battery charge not lasting very long at all??

    iPhone 5 getting really hot and battery charge not lasting very long at all??

    Try some of these to save battery time:
    Settings>Notifications>[Turn off any notifications you don't need]
    Settings>General>Software Update (Make sure you're up to date)
    Settings>Brightness & Wallpaper> Auto-Brightness on (And that your brightness is not to the max)
    Settings>Privacy>Location Services>Turn off/Stop apps from using it
    Settings>Bluetooth>Off
    Settings>Mail, Contacts, Calendars>Fetch New Data>Manually
    Settings>Wi-Fi> Off (When you don't need internet when you're out and about)
    To stop overheating, note these:
    Operating Temperatures: 0° to 35° C (32° to 95° F)
    Non-Operating Temperatures: -20° to 45° C (-4° to 113° F)
    Hope this helps!

  • Problem with Big Bang z77 mpower and USB3

    I built my pc last night and everything was working just fine. I have 3 external harddrives connected to the USB3.0 ports in the back. Last night, I was able to see all 3 (along with my 4 internal harddrives (1ssd, 3 hdd)). I turn it off for the night and then this morning, the only thing I was seeing was my internals. Nothing changed between then and now. I did see a UB91 in the device manager with a yellow triangle.. updated all my USB controller drivers via the downloads from MSi's website which got rid of the yellow device but my USB drives are still not showing. My USB2 ports seem to be working. My mouse/keyboard are connected to the ones in the back. I connected a thumb drive to the front ports of my HAF case (both USB 2.0 and 3.0 ports) and it showed up in each one. Not sure why my back USB3.0 ports are no longer working.
    Other parts in the build are:
    Intel i7 3770k
    2 x 4GB DDR3 1600 MHz
    nVidia GTX 680
    Any ideas what I can do or if its a mobo failure?
    Edit: Forgot to put I am running Windows 7 Ultimate 64 Bit.

    Quote from: pikka68 on 30-March-13, 01:11:43
    The site msi: http://www.msi.com/product/mb/Z77-MPOWER.html#/?div=Detail
    USB 3.0
    • 6 USB 3.0 rear I/O ports (2 ports by Intel® Z77, 4 ports by Renesas®uDP72020
    The site Renesas:  http://www.station-drivers.com/page/renesas.htm
    is located : uPD720200 & uPD720200a , and uPD720201 & uPD720202
    Syntax error or other reason?!    uDP----uPD
    Quote from: xmad on 30-March-13, 01:19:29
    I had a bunch of trouble getting my BBxII to flash with win 8.
    Try opening an elevated cmd promt and manually typing the commands using the files from station drivers.
    Syntax:
    w200fw35 /srom 0 /writeall f401502.mem cfg.ini
    if that one doest work, replace the other firmware: f302808.mem
    I attached the package, just extract them somewhere easy to naviagate.
    tried .. the two options .. always "dece not found"!
    Syntax error or other reason?!    uDP----uPD
    thanks for your help ..
    Greetings ..
    Pikka68

  • Mouse to switch primary and seconds buttons not working on Forms 6i

    Hi All,
    I am facing problem while i am using Form6i Application on web.
    We have a couple users that they are left hand. When they set their mouse to switch primary and seconds buttons under windows setup.
    The menus do not worked on Form6i Application, unless the user uses the keyboard.
    On Form10g it's working fine but on Form6i it's not working.
    Thanks in Advance.
    Uzair

    Hi Craig and thanks for replying,
    The way I created the roll was under my username, not the administrator user. The first time I was not able to create a roll from my user, but I did this to be able to do it: GRANT CREATE ROLL TO <MY USERNAME>
    The way I enabled the the Roles on y menu was as follows:
    1) I open menu using Forms 6i.
    2) Right click on my menu name and choose Property Palette.
    3) Under Menu Security, I choose Use Security and select "Yes".
    4) Under Module Roles, I typed a name for that role.
    5) I go to SQL and create the new Role under my username giving the role the same name I gave it on Forms. This is how I created: Create role <Role Name>
    6) Then I just assign that role to my user, like this: Grant <Rolename> to <username>
    Hope this helps!!
    Thanks again in advance!!

  • Z77 mpower and h80i

    Does anybody know if the z77 mpower suffers from the loose backplate issue? I have already installed mine, I did notice that the backplate was loose, but thought it was normal. I have very high tems (idles at about 40 and load at 72). Thanx a lot!

    the problem only happens with some mobo's apparently.  was just hoping some one has already tested this.

  • Icloud and outlook 2007 not communicating any longer

    I just noticed today that entries I made on my iphone (3gs using IOS6) are no longer showing up on my outlook 2007. (PC using vista 64)  the icloud calendar is not checked on outlook and when I check it to bring up my icloud calendar it says, "The set of folders cannot be opened. The information store could not be opened."  I try to get on the icloud control panel (I upgraded it several days ago to the icloud 2) and it says, "Repair the icloud control panel to use icloud with outlook"  I have repaired it over a dozen times now.  I have done a repair of my outlook.  I have taken icloud off and then reinstalled it to have it tell me the same thing.  I'm at wits end.  This was working three days ago, but now its as if they don't see each other.  If this has already been discussed, I apologize.  I did do a quick search and did not see anything that would help.  Any suggestions would be appreciated.

    Yes it is elsewhere, however I have a Vista 32-bit that doesn't work and a Windows/7 64bit that doesn't work.  I think it's just generally "bad code" and OBVIOUSLY the person that was supposed to test it didn't.  I can't uninstall on my Vista machine because it will break all my Contacts and Calendar sharing too.  Therefore, for now, I guess I will just have to give up on sharing pictures until they get it fixed.
    Which, BTW, has been an AWFULLY LONG TIME already.  I installed v2 over a week ago and Apple hasn't even acknowledged anywhere I've seen that they have an issue.
    'Bout time to start sending emails to the press:  Maybe they can goad Apple into doing something.
    There are several articles expounding about how great it is:  I will be replying to all I can find that it DOES NOT WORK AND APPLE DOES NOT CARE.  They sold several million new phones, all made in China, and now they are fat, dumb and happy.

  • Z77 mpower and windows 8.1 enterprise: 5.1 sound not working

    Hi All!
    Help me please!
    I install windows 8.1 Enterprise. My audio only work in stereo. My home cinema is connected my PC, (previous OS: win7 Enterprise: audio is work in 5.1) My cinema is testing: work in 5.1 .
    PC realtek audio not working, only 2.0
    what can i doing?
    newest drivers in installed.
    Help me please!
     

    I've the same problem with my Z87-G45.
    The button "fill speakers" in the last Realtek 1150 driver simply doesn't work at all.
    It perfectly works Under Windows 8.1 drivers, but I can not correct my room with Windows driver.
    Please could you help us or fix it ?
    Thanks

  • Server 10.5 on PPC with software RAID not bootable?

    I read in this article (http://docs.info.apple.com/article.html?path=ServerAdmin/10.5/en/c5sa15.html) that "No PPC-based Macs support booting from software RAID volumes."
    I believe that this is not true! From my software dealer i was told there should be no problems to do this. I called Apple and the guy i spoke with also told me that it works fine. I actually now have set up a software RAID1 (PPC G5 2.3Ghz, 2x500GB HD) from wich i boot and it does work!
    My question is: Are there any risks to continue running this installation?
    /Andreas

    One risk is you can't partition an Apple software RAID 1 in Boot and Data volumes so you could potentially have either overwrite "the other". An "overfull" share can damage the system and vice versa.
    And write performance can suffer because writes aren't simultaneous (?).
    Another risk is the server woun't tell you when one disk fails so if you don't notice when the other one also fails the data on the first one is old (backups are essential as usual). Or if thinking "there is a "failover" disk available" when it too already have failed a while ago (but ofcourse no worse than having only 1 drive and no mirror).
    Depending on the cause of failiure, software/glitch or mechanical, the disks can be in different "shape" if you have to try restoring the data.
    A good idéa is have an extra drive (firewire?) you backup (one way synch replacing/removing old files/removed files) to every night.

  • Msi z77 mpower sli and areca raid controller

    Hello, i own an Msi z77 mpower and i have recently upgraded to an SLI config (dual GTX680's)
    The problem is since then i can't get my hardware raid card (Areca arc-1212, with latest bios) to work, it bleeps but i don't get the raid info screen or menu.
    I've put both the graphic cards in the top two pcie 16x slots (PCI_E2 and PCI_E5) and my Areca in the bottom one (PCI_E7)
    As far as i understand i should be able to run 3 pcie cards at 8x/4x/4x right?
    The only slot where the Areca works is the PCI_E5 slot, and i can't put a GTX680 in the PCI_E7 slot because of spacing.
    I'm also running a Xonar sound card in one of the pcie 1x slots (PCI_E4)
    Running with a Intel I7 3770k and 4x4gb of ram and Windows 7 x64.
    I'm running the latest beta bios.
    Please help!

    Quote from: jhroom on 28-February-13, 07:39:35
    Thanks for the fast reply!
    But what use does the 3th slot have then?
    Also a 4x gen3 slot has the same bandwith as a 8x gen2 slot right?
    I feel a bit mislead, knowing this i would have chose a different board.
    Other boards will have the same problem. The CPU has 16 lanes to divide and Nvidia demands 8/8 for SLI. That leaves no lanes left for the third slot.
    Using CrossFire should leave you 8/4/4 as AMD doesn't demand 8/8 for CrossFire.
    You'll need the use the slots using the lanes coming from the PCH if you want to use additional PCI-e devices.
    The X79 platform might suite your needs better. That has 32 lanes to divide from the CPU + the ones from the PCH.

  • [SOLVED] Z77 Mpower can't detect second graphic card

    Hi everyone
    I'm experiencing a problem with my Z77 Mpower.
    It's not able to detect the second graphic card.
    The complete configuration includes:
    Z77 Mpower
    i5 2500k
    2*4Go G.skill 1866MHz
    GTX680
    8800GT
    Crucial M4 256Go
    Corsair AX750
    The idea was recycling my old 8800GT as a dedicated physx card
    Due to massive cooling the GTX680 will be installed on the second port
    Both graphic cards works perfectly when installed alone and I also tested with a GTX570 and results are the same
    When I install only one card, it works on 1st port at 16x or 2nd port at 8x,
    but if there is 2 cards installed only the first works and bus-width is 8x according to CPU-Z, the second one is invisible in windows, GPU-Z or driver
    I didn't tested the 3rd port because my sandy bridge has limited pcie lane
    I tested it with bios 17.4 and beta H53, results are the same, I also tried with and without 6 pins power supply on the mainboard and the problem is still the same.
    I tried this graphic cards configuration on a gigabyte z68 ud4 and same cpu, ram, vga and psu and it works perfectly.
    Is there a bios setting to enable multi gpu ? (tried to enable igp multi screen without result)
    Is it possible to have defective pcie port for multi gpu when all pcie ports works alone ?
    I have another question about this motherboard
    is it possible to have a dynamic vcore related to eist while overclocking ?
    on the gigabyte z68 ud4 it's possible by setting vcore on normal and playing with load line calibration and offset
    on the mpower this settings appears in bios but are not graduated the same way and I don't understand how they works.
    Thanks for your help

    Thanks for your help flobelix
    I already tried and benched this physx configuration on my old gigabyte motherboard
    in non physx games the 8x limitation barely don't affect the gtx680
    in physx games the 8800gt isn't fully loaded and framerate is near the gtx680 alone with physx disabled.
    this configuration gives physx graphical bonus without affecting framerate
    the 120W limit of the MK13 may be for fanless use, I have 2 90mm fans attached directly on the heatsink and under furmark the card runs 20°C lower than stock cooling and is very silent
    I also kept the stock molded metal plate that cool the power supply and ram under the MK13
    But due to this cooling this card can't be installed on the first slot
    on the gigabyte until you set the dedicated physx card in the driver both cards and all outputs on cards sends the same signal to screen (bios screen is also sent to all cards)
    on my mpower only the first sends signal to screen, but i should be able to set (only for testing purpose) the 8800gt as main device and the gts680 as physx card
    unfortunately it don't work because it looks like when a card is plugged on 1st port the mainboard disables the 2nd

  • MSI Z77 MPower sound problem

    I have MSI Z77 MPower and i have problem with sound. When i play audio i have feeling that sound automatically volume up and volume down. When i uninstall THX i have feeling that is everything OK but sound is not loud like before.I try on THX turn off smart volume and cristalyzer but problem is still here. Can you help me.

    I had the same issue with an early version of THX, have you downloaded the newest version from the website?
    >>MSI Downloads<<
    Update all of your drivers and re-test. In my case I just un-installed THX until the next version came out and it's fine now.

  • MSI Z77 MPOWER RAM compatablilty.

    Hi,
    I am building my first computer and plan on buying the MSI Z77 MPOWER soon, but im not sure if the RAM I have chosen is compatible with the MB as they are not in the compatibility list.
    System specs:
    case: CoolerMaster Storm Trooper
    CPU: i7 3770k (hopefully overclock'd to 4.6ghz)
    RAM: 16GB
    GPU: 2x Nvidia 480 SLI
    HDD: 120GB SSD (to start with)
    OS: Windows 7
    RAM in question:
    Corsair Vengeance CMZ16GX3M2A1600C9 16GB (2x8GB) DDR3
    or
    Corsair Vengeance Pro CMY16GX3M2A1600C9R 16GB (2x8GB) DDR3
    Thank you in advance
    mike.

    Manufacturers cannot test each and every RAM in the market.
    Corsair Vengeance RAM has proven to be compatible with just about every MSI board. Their RAM is normally JEDEC standard and you should not have any problems. Either one of those kits should serve you well.

  • Solaris 10 cd's not bootable

    We have original sets of Solaris 10 and downloaded from Sun website and they are not bootable. We were thinking at a minimum that cd1 would be, but it isn't. The DVD is bootable and works fine, we're having problems with the CD set. Anyone have this problem or can recommend a fix?
    Thanks
    -Chris

    I'm assuming you have downloaded for the right architecture (sparc or x86).
    Can you try booting up with the CD on another machine? If that works, the problem is on your system. What kind of system are you using?
    If you can't boot up from CD on another machine, that means you CD is defective. In that case, I would suggest downloading them again and run md5 check on them.

  • I have an two ipod first ipod is my updated in itunes and second doesnot update it show that your ipod is updatedso pls pls pls tell me problem

    i have an two ipod my first ipod is updated with4-3-3 version in itunes and second does not update in same itunes what had happen pls pls pls pls tell me

    See:
    iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
    If you have Snow Leopard do not forget the Additional Information paragraph.

  • Spefications for Pdt Name,Serial Number and Pdt Number not working in HPSA

    HP technical support came and replaced a new motherboard on Feb 5, 2015. Also,  I have not being accessing HPSA for quite some time now and I am not aware how long has this take place.
     When I access HPSA, under System Information, only Product Name, Serial Number and Product Number are not mentioned.
    I recently updated to the latest version of HPSA today(Feb 7, 2015), but it still can't read them.
    What can be done so that HPSA can read them. 
    Please guide me accordingly.

    Hi @aswann, 
    I have brought your issue to the attention of an appropriate team within HP. They will likely request information from you in order to look up your case details or product serial number. Please look for a private message after the weekend from an identified HP contact. Additionally, keep in mind not to publically post ( serial numbers and case details)
    If you are unfamiliar with how the Forum's private message capability works, you can learn about that here.
    Regards,
    George
    I work for HP

Maybe you are looking for