Z77 Mpower Problem

Hello to all from Greece.
Recently i bought the new pc and today i tried to enable the Vitru MVP i had go to bios and i had make some changes on the section with vitru mvp us i remember i had change the PEG to IGD when i do this change and i press F10 to save the computer restart and then i see only an blank screen with error message on the motherboard 62 (Late CPU Initialization) i had change the bios on bios B and us i see is working good !! then i tried to make cmos clear (also i had remove the batter for 10 minutes) but nothing happens i see only a blank screen, also i had remove all memories from the pc and nothing from beep. now i am working from bios b i had make also to this bios clear cmos but the problem on bios a i steel there. what i must do now??? please help me. also i had updated with the latest bios but nothing i had update the bios from live update 5 in windows.
My system is
Case : strike_x_st_black
PSU : AX1200i Digital ATX Power Supply
MotherBoard : MSI - Z77 MPOWER
CPU : Intel Core i7 3770k
Memory : G.SKILL [ TridentX ] F3-2600C10D-8GTXD
VGA : MSI N680GTX Lightning
Hard Disk 1 : TRANSCEND SSD 320 128GB SATA3 6,4cm MLC Solid State Disk (TS128GSSD320)
Hard Disk 2 : WD Caviar Black WD2002FAEX 2TB SATA-600 - 7200 U-min Puffer: 64MB (WD2002FAEX)
Blu-Ray Recorder : ASUS BW-12B1LT
Camera : Logitech HD PRO WEBCAM C920 Full HD Webcam
WaterCooling : Thermaltake Tt Water 2.0 Extreme (CLW0217)
Compoud : Arctic Silver Silver 5

Quote from: xmad on 03-October-12, 09:44:11
Yes, what you are doing is loading the working bios, then flipping the switch so that you flash the broken one. It is not something you normally want to do, but it is how to recover the Bios A. You just must make sure that you do not touch the switch until the bios is finished loading and the flash tool selection screen is up.
https://forum-en.msi.com/index.php?topic=160450.0
now i see 3 options
1. Run memtest86+
2. Proceed with Update
3. flash back the prevision BIOS
now i change to A BIOS????

Similar Messages

Z77 mpower problems.

Hello all
Just bought this board and I must say it is a good looking board.
I have a few issues.
1) The wireless adaptor does not work. I have installed latest drivers but it shows up in device manager as not active
2) I can not get my memory to run at 1600 mhz....every time i change it in bios it changes back to 1333 mhz after reboot......any one know what I am doing wrong?
3) I successfully connected to my mobile via bluetooth but when i look in the folders for my pictures there are none there, any idea what this is caused by
thanks in advance.

well i just about given up here.....half the time you cant change the settings you want to change in bios because nothing happens when you click on something. after hours of messing around yesterday I decided to unistall all bios/control progs from windows in case it was those that were interfering with the settings i was putting into bios. Then could not find any where to disable oc genie as you said so I manually set cpu to 4.2 and memory to 1600 mhz. It booted up ok...ran a benchmark and memory was running at correct speed. Rebooted and now the memory is down to 670 mhz again.....anyone know what it is...does this board not like crucial memory....or maybe not like running 4 sticks of memory?
HELP!

Problem with starting msi z77 Mpower

Hello
i 've just bought a Cooler Master Silent Pro Gold 800W
and a mobo msi z77 mpower(today)
i have this problem
i have tested the psu with 2 different mobo (the msi stated before and a asus p8z77 v pro) and in both cases the psu fan runs for few seconds and the it stops.i have tried it with and without cpu , with and without case fans , i have the same problem it turns the fans for few seconds and then it stops as if dose not have enough power.
tested the psu with the paper clip test and it works , but when i put the 24 pin connectors and the 8 pin connectors on the motherboard it dosen't. Maybe i do something wrong ?
I've speak with tech support from cooler master and it seems it's not the psu
honestly i don't know what eles to try /do
can you help me?
thank you in advance

To go a step farther, when the board is outside of the case, you should have a monitor connected to the onboard graphics or a discrete card, 1 stick of RAM in the primary DIMM slot, and CPU with it's cooler for initial startup. Be sure to test on a non conductive surface of unprinted plain cardboard or an untreated wood surface.

MSI Z77 MPower sound problem

I have MSI Z77 MPower and i have problem with sound. When i play audio i have feeling that sound automatically volume up and volume down. When i uninstall THX i have feeling that is everything OK but sound is not loud like before.I try on THX turn off smart volume and cristalyzer but problem is still here. Can you help me.

I had the same issue with an early version of THX, have you downloaded the newest version from the website?
>>MSI Downloads<<
Update all of your drivers and re-test. In my case I just un-installed THX until the next version came out and it's fine now.

MOVED: BCLK STUCK!!! BIOS 17.6 Problem with Prefetcher???MSI Z77 Mpower

This topic has been moved to Overclocking, Undervolting.
https://forum-en.msi.com/index.php?topic=165456.0

Quote from: xmad on 17-January-13, 08:44:47
Also for best oc result flash to the lastest release or beta bios listed here.
>>Beta BIOSes<<
Follow the directons to make sure the manaement engine extension of bios is flashed as well.
Follow this link to some screen shots of other z77's using various overcocks:
https://forum-en.msi.com/index.php?topic=162043.0
Have the latest BIOS and latest management extension flashed as well.
I have had this work before with no problems. I was one of the first people to get a MSI Z77 Mpower board. Never had this type of problem with any other BIOS. Problem started with 17.6 BIOS. I have had all the BIOS flashed on my RIG since I have had it.
Not sure what the problem is. Thanks for you help. Those over clocking charts are helpful but not specific to MSI Z77 Mpower mother board and the BIOS is different. Not sure if they are updated to include the new CPU features of "Hardware Prefetcher" item and "Adjacent Cache Line Prefetch" that BIOS 17.6 started to use.

BCLK STUCK!!! BIOS 17.6 Problem with Prefetcher???MSI Z77 Mpower

BIOS 17.6 added the new CPU features.
I think the new BIOS CPU features of "Hardware Prefetcher" item and "Adjacent Cache Line Prefetch" options are part of the problem. When I disable hardware prefetcher my memory performance shoots way down. BUGGY!!!!
I am unable to over clock my BCLK. What is going on!!! HELP!!!

Quote from: xmad on 17-January-13, 08:44:47
Also for best oc result flash to the lastest release or beta bios listed here.
>>Beta BIOSes<<
Follow the directons to make sure the manaement engine extension of bios is flashed as well.
Follow this link to some screen shots of other z77's using various overcocks:
https://forum-en.msi.com/index.php?topic=162043.0
Have the latest BIOS and latest management extension flashed as well.
I have had this work before with no problems. I was one of the first people to get a MSI Z77 Mpower board. Never had this type of problem with any other BIOS. Problem started with 17.6 BIOS. I have had all the BIOS flashed on my RIG since I have had it.
Not sure what the problem is. Thanks for you help. Those over clocking charts are helpful but not specific to MSI Z77 Mpower mother board and the BIOS is different. Not sure if they are updated to include the new CPU features of "Hardware Prefetcher" item and "Adjacent Cache Line Prefetch" that BIOS 17.6 started to use.

Z77 MPower RAM problems (BSOD)

Hi!
So i'm writing on this forum because im having huge problems with BSOD (0x0000001a - Memory managment) on my z77 mpower mobo.
My PC:
Windows 7
Intel i5 - 3570K
MSI Z77 MPOWER
ATI HD5850
G.Skill 4GBx2 (F3-12800cl9d-8GBXL)
Corsair TX650
Latest Beta Bios (Same in 17.3, 17.4)
Problems emerges when i put RAM in slot #2 and #4 like described in manuals (initial slots). I even get errors on Memtest86 but when I put RAM in slots #1 and #3 there is no Memtest errors. If i test only 1 bank of memory i get wierd timming in Memtest .
RAM: 804 MHz (DDR3-1608) / CAS : 6-6-6-20 (11-11-11-28 when in dual channel) - Original timming are 9-9-9-24. And when im using single stick of ram slot 1 or 2 have timmings 6-6-6-20 and slot 3 and 4 have 11-11-11-28.
About that error in memtest86. I get error (1 error every loop) in test 8. If I lauch memtest86 right after BSOD (always the same) i get 300 errors in 10 seconds (SLOT 2 AND 4) .
XMP does not solve BSODs.
I dont really know what else could i write to help you understand my problem .

Quote from: xmad on 21-November-12, 02:19:57
I suggest you borrow some memory to test(Any other DDR3), if the problem re-presents itself, I suggest you remove the cpu and inspect the cpu pins for damage. Do this with a bright light and magnifying glass.
already inspected pins and all is fine. Now i need other RAM to test.
Quote from: Froggy Gremlin on 21-November-12, 03:31:36
If you are getting errors in Memtest, the RAM is most likely at fault and should be replaced. As for the CPU-Z readings, they can't be completely trusted. I see once in awhile on the SPD Tab the wrong chip programming being reported, so glitches exist with the SW. Does CPU-Z still read wrong when just one RAM stick is placed in DIMM 2, the primary DIMM slot which is the second slot from the CPU?
The RAM sticks should be initially tested each individually using Memtest in the primary DIMM slot, not both together in slots 2 and 4, or 1 and 3. IMO, you have a factory screwup mismatch labeled kit of RAM or something.
Having some bent or damaged CPU socket pins is also a possible, although this usually is indicated by failure to POST or boot, and DIMM slots 1 and 2, or 3 and 4 will not function at all.
About that second slot.
Inserted RAM CPUZ detection
slot1 slot 3
slot2 slot 4
slot3 slot 1
slot4 slot 2
i was testing with only 1 stick. I intend to test RAM in slot 2 like you said but what are those off timmings :S. RAM (9-9-9-24) but in memtest (4.20 or 5.0 Beta) are set to 6-6-6-20 and i cannot change it even with XMP profile or manual settings :S but in cpu-z show the correct timmings.

Z77 Mpower+ GTX 295 problems.

Hi all
I have an Z77 mpower motherboard with Avexir MPower Series 8GB (2x4GB) DDR3 PC3-19200C10 2400MHz Dual Channel Kit and a i5 3570k.
When the mobo is at deafults in the bios then all is ok..not one problem.
but if I do a small OC [email protected] using turbo and use the XMP on the ram
Then most times it gets to windows the I get a black screen and my monitor says "No video input"
Now on my 295 dual pcb I have a blue light(for power)and a green light that comes on when I am connected to a screen.
What I have noticed is that for some reason the mobo will switch off the screen side of my 295(the green light is now out)
and some times when it gets to the windows logon screen it turns off the power light!
At the MSI mpower page it says that a GTX 295 with the firmware of 62.00.6C.00.01/02 has been tested
my firmware is 62.00.45.00.02(P0657-7000) not the same so?
I have tried my 295 in another i5 mobo(gigabyte) and all is ok, my power supply is a Silverstone 650W SLI.
Any help would be good
Thank you for your time.

Quote from: xmad on 22-March-13, 00:14:59
There is another user with this exact error. Best to contact MSI, I'll send them an email and see if there is a known issue.
Please let me know which ME version is installed. Check in UEFI bios for this.
Thanks
>>How to contact MSI.<<
Edit: Try this version as well:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&DwnldID=22092&keyword=management+engine&lang=eng
I also recommended to the other user to remove control center then do a registry search for it and delete any left over keys and files. Then re-install see if it helps.
Thanks xmad
I will uninstall control centre in a bit and do as you say.
I have told MSI support but all they say is they can't replicate the problem and they never heard about it.
The ME driver is installed this "please replace the ME version" will it cause any other problems other than control panel?
because I can live with out it. I will look at my ME version when my 480s come tomoz.
As I am hooked to my monitor using the built in graphics and it don't like my monitor lol.
Thanks again...Hello MSI support..please pay these guys or give them some great freebies..thank you

[SOLVED] Z77 Mpower PCI LANE problem [MSI 7751]

hi peoples i'm a new here as new user of MSI motherboard, this is my first MSI motherboard, and i allready have a problem with it.
as the manual suggest, for a single gpu configuration i should use pci_e2 (page 1-19)
i've tried GTX 260 216sp no go , black screen no system post ,and pressed reset button like 10 time, didn't work, it worked once and never again, and gpu-z shows [PCI-E 16X2.0 @ X4.0]
i've tried AMD 3850x2 no go , black screen no system post
i've tried 9600GT no go , black screen no system post
i've tried 9500GT no go, black screen no system post
i've tried 9800GTX no go black screen no system post
then each of this vga shifted on pci_e5 and worked at the first system startup
is the mainboard faulty?!
PC SPECH :
i7 3770K @ stock speed
Mainboard : z77 mpower latest bios installed
Storage : SSD Crucial 64 Gb
PSU : enermax revo 85+ 1050w
Ram: corsair platinum 2400c9 2x4gb
Windows Xp 32bit
Windows 7 x64 [7601]
i may think this board is faulty isn't it?
the previous mainboard was an Asus Gene Z77 wich didn't give me any kind of problem, cpu ram and psu were the same and worked perfectly.
is there a way to fix this or i should send it back!?
thanks for the help.

Quote from: xmad on 21-October-12, 10:19:28
Remove the board and make sure there are no extra stand off or screws shorting the case.
[cut]
just tried , no go at all ...
Quote from: Froggy Gremlin on 21-October-12, 12:41:50
If you have tried all the applicable suggestions previously mentioned in this thread, try the newest Beta UEFI/BIOS found here;
>> Beta <<
wich one please? i see so many ...
edit: found. i'm trying now.
Quote from: Froggy Gremlin on 21-October-12, 12:13:35
Presume in GPU-Z it was reading 2.0 @ 8X? I think the suggestions are correct. This is a classic behavior of bent or damaged CPU socket pin(s). Could be a faulty PCI-E slot, errant standoff underneath the mainboard, or even a more rare faulty CPU. Uneven mounting or torque pressure of the CPU cooler could also cause this behavior.
what does it mean? should i still have to wait like one month or much more to get a new board since it arrived faulty?

Problem with Big Bang z77 mpower and USB3

I built my pc last night and everything was working just fine. I have 3 external harddrives connected to the USB3.0 ports in the back. Last night, I was able to see all 3 (along with my 4 internal harddrives (1ssd, 3 hdd)). I turn it off for the night and then this morning, the only thing I was seeing was my internals. Nothing changed between then and now. I did see a UB91 in the device manager with a yellow triangle.. updated all my USB controller drivers via the downloads from MSi's website which got rid of the yellow device but my USB drives are still not showing. My USB2 ports seem to be working. My mouse/keyboard are connected to the ones in the back. I connected a thumb drive to the front ports of my HAF case (both USB 2.0 and 3.0 ports) and it showed up in each one. Not sure why my back USB3.0 ports are no longer working.
Other parts in the build are:
Intel i7 3770k
2 x 4GB DDR3 1600 MHz
nVidia GTX 680
Any ideas what I can do or if its a mobo failure?
Edit: Forgot to put I am running Windows 7 Ultimate 64 Bit.

Quote from: pikka68 on 30-March-13, 01:11:43
The site msi: http://www.msi.com/product/mb/Z77-MPOWER.html#/?div=Detail
USB 3.0
• 6 USB 3.0 rear I/O ports (2 ports by Intel® Z77, 4 ports by Renesas®uDP72020
The site Renesas: http://www.station-drivers.com/page/renesas.htm
is located : uPD720200 & uPD720200a , and uPD720201 & uPD720202
Syntax error or other reason?! uDP----uPD
Quote from: xmad on 30-March-13, 01:19:29
I had a bunch of trouble getting my BBxII to flash with win 8.
Try opening an elevated cmd promt and manually typing the commands using the files from station drivers.
Syntax:
w200fw35 /srom 0 /writeall f401502.mem cfg.ini
if that one doest work, replace the other firmware: f302808.mem
I attached the package, just extract them somewhere easy to naviagate.
tried .. the two options .. always "dece not found"!
Syntax error or other reason?! uDP----uPD
thanks for your help ..
Greetings ..
Pikka68

Z77 Mpower boot issue - won't POST

Hi there
Got a question regarding a PC build that isn't working as well as hoped. Doing this on behalf of my friend but I've been helping him while he builds it so have a good idea of what's been going on.
Set up is as follows:
Processor: Core i5 3570k (stock, not overclocked or anything)
Motherboard: MSI Z77 Mpower
RAM: 8GB Corsair Vengeance memory (in 2x4gb)
PSU: Corsair 800W Gaming PSU
Storage: OCZ 240GB SSD
Cooling: Zalman water cooling (can't remember the exact model off hand I'm afraid, will try and get that later)
Graphics: HD 4000 integrated (for now, haven't got the graphics card yet)
We built the machine and got it going no problem. When it was first built it booted no problem, so we set up boot priorities and then installed the Windows 8 Enterprise 90 day trial. All good so far. Installed no problem at all at lightning speed and we got into Windows fine. Installed lots of drivers and so forth with no such trouble either. CPU was reporting a steady 25C average temperature on idle and everything seemed to be going smoothly.
Then we hit a stumbling block. We powered off the machine to make a minor adjustment in the case (all while static protected with a wristband), and after doing this we then powered the machine back on. We're now getting a dim red LED (almost seemed half powered) in the DrMOS overheat warning and then two bright blue LEDs next to it indicating the CPU power phase. The fans will spin and case LEDs come on, but nothing else happens other than that and the LEDs. No POST screen or anything like that. It might also be worth noting that now when you plug the computer in, the green LED on the internal power button no longer lights while the machine is off - when the machine was working it would.
I've spent hours trawling through the forums and can't seem to find the same problem happening. We're getting a bit worried that there could be a fault on the board but wondered if we could get some advice from here first. I tried resetting the CMOS with no avail and trying the other BIOS.
As a last resort, we've now removed the cooler and CPU to check the CPU hasn't melted or anything drastic like that and it's absolutely fine - no visible damage. We've left it like that for now until I can get back over there with some more thermal paste to reseat the processor and cooler so until then we're stuck anyway.
If anyone has any ideas or knows of the problem, it would be really appreciated as we're a bit worried! What should we try?
Thank you!

Many thanks, will give that a try. Is it an RMA to MSI if that fails then? Forgive me for not totally understanding consumer rights - but it was only bought around a week ago - could we get the supplier to exchange it or would it have to go to MSI for repair?
Quote from: xmad on 27-December-12, 05:16:31
Next, remove the main board and place it on a non-conductive surface and test it with a single stick of ram in dimm 2, cpu & cooler. You can try switching the ram ram sticks and dimms, but the last few times I saw anything about the drmos alarm it was a defective mainboard.
While it is out and the cpu is removed though, take a good look at the cpu socket pins and count all the stand off to make sure there are not extras.

MSI Z77 MPower Ram issues

Hi guys
I recently installed the MSI Z77 MPower after replacing it with the Asrock extreme 4 mobo which i had before, am currently having problems with the RAM it wont boot if i place them in the correct slots for dual channel configurations but if i place them in the last two slots the PC boots up fine.
My Ram is the G Skill Ripjaw X series 1600mhz model number: F3-12800CL8-4GBXM.
Its driving me nuts two motherboards and nothing working, i just hope its not relating to my CPU or something like that.
Please...please guys really need your help with this, because without it running in dual channel configuration my first build feels incomplete due to this problem.
Thanks in advance

Hi guys thanks for the replies and sorry for the late reply has i said before my MSI MPOWER Z77 motherboard is totally brand new and i know for a fact that no bent pins in the cpu socket, from what i am aware of, if my RAM is related due to the type of RAM modules that i am using and you guys are suggesting corsair modules which ones do you guys recommend me getting. You know when i said only slot 3 and 4 only worked could that be in a result of the RAM am using or not....??
Thanks in advance guys

Z77 mpower and h80i

Does anybody know if the z77 mpower suffers from the loose backplate issue? I have already installed mine, I did notice that the backplate was loose, but thought it was normal. I have very high tems (idles at about 40 and load at 72). Thanx a lot!

the problem only happens with some mobo's apparently. was just hoping some one has already tested this.

Z77 Mpower SATA connectors

Hi guys,
I noticed that who assembled the pc connected the dvd rom to the SATA 6Gb connector and the SSD to the 3Gb connector.
Can I invert them safely ? Or I could encounter problems at the boot ?
Thanks

I think you shoul invert.
I've just installed Z77 Mpower on my config and for now just plugged a SSD on SATA1 (6Gb) and DVD pionner DVR 216 on sata 3.
On this motherboard, only sata 1 and 2 are 6Gb compliants, so you don't use most powerful of your SSD as you should if it plugged in sata 3~6.
Maybe you 'll only have a message on next boot, due to plugs modifications, validate and ok
Test speed of your SSD with crystaldiskmark before and after change, you 'll see if you win read/write Mb/s

Debug led Panel FF Z77 mpower

Hi ! I have problem with computer I can't go to bios i have error on led (FF) on modo z77 mpower .How i can fix this and start bios and set default?

Arctic Silver Arctic srebrny 5 (3.5g)
Be Quiet! STRAIGHT POWER E9 600W (BN193) 80+ GOLD (BN193)
LED Dell U2312HM
Corsair Carbide Series 500R Mid-Tower Gaming Chassis (CC-9011013-WW)
Kingston HyperX 2x4GB 1600MHz DDR3 Non-ECC CL9 Intel XMP X2 Grey Series (KHX1600C9D3X2K2/8GX)
Asus DRW-24B5ST SATA CZARNY (DRW-24B5ST/BLK/G/AS)
Intel Core i7-3770K, 3.5GHz, 8MB, LGA1155, 22mm, 77W, BOX (BX80637I73770K)
Gigabyte GeForce GTX670 2048MB DDR5/256bit DVI/HDMI/DP PCI-E (1058/6008) (wer. OC - OverClock) (GV-N670OC-2GD)
Western Digital Caviar Blue, 3.5'', 1TB, SATA/600, 7200RPM, 64MB cache (WD10EZEX)
SSD Samsung 256GB SSD830 SATAIII, MLC, 2.5'' (read/write 520/400MB/s) 7mm (MZ-7PC256B/WW)
MOBO MSI Z77 MPOWER
CPU Thermalright HR-02 - Macho - Black White
I switch dual bios and nothing , reset bios too . So i need check cpu and check pins

Z77 Mpower Problem

Similar Messages

Maybe you are looking for